Quick Reference

Tabmeof Contents:Pages

[] Product dimensions

[] Cutout dimensions

[] Before you start

[] EbctdcaU requirements

[] [] installation steps

If you need assistance:

Check your Use and Care Guide for a toll-free numberto call or call the dealer from whom you purchasedthis appliance. The dealer is listed in the Yellow Pagesof your phone directory under "Appliances-Household -- Major -- Service and Repair."

Call when you:

[_ Have questions about builtqn oven installation oroperation,

[_ Need to obtain the name and number of anauthorized service company.

When you call, you will need:

[_ The builtqn oven model number.[_ The built-in oven serial number.

Both numbers are listed on the model/serial ratingplate, located on the oven door or on the oven frame.

SingUeoven DoubUeoven

28o3/8"(72,1 ore} reax_

recessed

49-I/2"{12&7 ore)recessed

height

23"(58,4 ore)reax.recessed

depth

727-3/4"{7&5 ore)rein,cutout

height

2_

"_------30"(7&2 cre) rein,_

cab net wdth

28=1/2"{72,4 ore)

cutout width

Singmeovenundercounter{without cooktopinstalled above)

1-1/2"(3.8 crel rein,top of cutoutto undersideof countertop

49-3/4"(126,4 ore)

rein,cutout

height

5ol/4" {13.3 ere)bottom of cutoutto floor

1=1/2" (&8 ore}rein_ bottom of

cutout to top ofcabinet door

3e" (7&2 crelmin, cabinet

28=1/2"_{72,4 cre)_

cutoutwidth

cabinet_-_-

23=1/4"(59,1 crel rein,cutout depth

23" (58.4 ore)_---recessed oven_

depth

J

recessed

oven_ ovenfront

Cabinet side view

Cabinet filler kits are available from your dealer.Use a matching color kit if oven is smaller thanyour cabinet opening.

Single oven filler height is 3o5/16" (8.4 cm)Black -- 4378941White -- 4378942Almond- 4378943

Double oven filler height is 6o5/16" (16 cm)Black -- 4378947White -- 4378948Almond- 4378949

27=3/4"{7&5 ore}

rein,cutout

height

1=1/2"(3,8 ere)

rein,bottom ofcutout to

top ofcabinet

door

Doubmeoven

30" (76.2 ore} rein,cabinet width

28=1/2"_----{72,4 cre}------:b,

cutoutwidth

Singmeoven

.j-

5I"

{12e.5 ore)reS)L

overall

height

i

1" (2,5 ore} topof cutout to

bottom of uppercabinet door

14=3/4"{37.5 ore)bottom

of cutoutto floor

1" (2,5 ore} topof cutout to

bottom of uppercabinet door

32"{813 ore)

bottom ofcutout to

floor

Year safety aRd the safety of ethers arevery important.

We have provided many important safetymessagesin this manual and on your appliance.Always readand obey alI safety messages.

This is the safety alert symbol.

This symbol alertsyou to potentialhazardsthat can kill or hurt you andothers.

AIi safety messageswiii foiiow the safety alertsymbol andeither the word "DANGER"or"WARNING"=Thesewords mean:

Youcan be killed or seriously injuredif youdon't fellow instructions.

AtIsafety' messageswilI tetI you what thepotentiai hazard is, teii you how to reducethechanceof injury, andteli you what can happenifthe instructions are not followed.

important: Observe all governing codesand ordinances.

Proper installation is your responsibility.Have a qualified technician install this even.

Oven location should be away from strongdraft areas, such as windows, doors andstrong heating vents.

Cabinet opening dimensions that are shownmust be used. Given dimensions provideminimum clearance.

Recessed installation area must providecomplete enclosure around the recessedportion of the oven.

ElectricaJ ground is required. See "Electricalrequirements."

Electrical suppJy junction box should belocated 3 inches (7.6 cm} maximum below thesupport surface when oven is installed in awall cabinet. Drill a 1-inch minimum (2.5 cm}diameter hole in the right rear or left rearcorner of the support surface to pass theappliance cable through to the junction box.For undercounter installation, it isrecommended that the junction box belocated in the adjacent right or left cabinet. Ifinstalling the junction box on rear wall behindoven, junction box must be recessed andlocated in the upper or lower right or leftcorner of cabinet.

It is the customer's responsibility:

To contact a qualified electrical installer.To assure that the electrical installation isadequate and in conformance with NationalElectrical Code, ANa{/NFPA 70 E latestlatest edition*, or Canadian L=lectdcalCode,C22.1-1982 and C22.2 No. 01982 (or latestedition)** and all local codes andordinances.

Copies of the standards listed may be obtained from:* National Fire Protection Association

Batteryreamh ParkQuincy, Massachusetts 02289

_ CSA International

8501 East Pleasant Valley RoadCleveland, Ohio 44131-5575

Tool

_/ PhimHps

screwdriver

Partssupplied:

4 screws (double oven)

Page 1

_fcodespermitandaseparategroundingwireisused,it isrecommendedthataqualifiedelectrician determine that thegrounding path and wire gauge are inaccordance with _oca_codes.

Do Not ground to a gas pipe.

Check with a qualified electrician if you arenot sure oven is proper_y grounded.

Do Not have a fuse in the neutral or

grounding circuit.

This oven must be connected to a groundedmetal permanent wiring system.

Oven must be connected to the propereUectdcaUvoffage and frequency as specifiedon the model/serial rating plate. (Themodel/serial rating plate is located on theoven door or on the oven frame.}

[_ Models rated from 7.3 to 9.6 kW at 240volts (5,5 to 7,2 kW at 208 volts} require aseparate @-ampere circuit. Models ratedat 7.2 kW and below at 240 volts (5.4 kWand below at 208 volts} require a separate30°ampere circuit.

[_ A timeodelay fuse or circuit breaker isrecommended.

[_ Connect directly to the fused disconnect(or circuit breaker box) through flexible,armored or non-metallic sheathed, coppercable (with grounding wire).

[_ Flexible armored cable from applianceshould be connected directly to junctionbox.

[_ Fuse both sides of the line.

[_ A U.L.-listed conduit connector must beprovided at the junction box.

[_ Do Not cut the conduit.Wire sizes and connections must conformwith the rating of the appliance and to therequirements of the National Electrical Code,ANSVNFPA 70 -- latest edition _, or CanadianElectrical Code, C22.1-1982 and C22.2 No.01982 (or latest edition) *_ and all local codesand ordinances.

if the house has aluminum wiring, follow theprocedure below.a.) Connect the aluminum wiring to the

copper wire using special connectorsdesigned and Underwriters Laboratories°listed for joining copper to aluminum.Follow the electrical connectormanufacturer's recommended procedure.

b.) Aluminum/copper connection mustconform with local codes and industry-accepted wiring practice.

Copies of the standards listed may be obtained from:National Fire Protection Association

Ratterymamh Park

Quincy, Massachusetts 02269

** CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131=5575

_ Grasp ovenframe to liftoven,

I IB

_ powersuppBy cable

]Remove

_ shippingfeet.

Use screws to attachoven to cabinet.

Reattach sidetrim.

Remove

trim screws.

Remove sidetrim.

_J_ Grasp ovenframe to liftoven.

Use screws toattach oven tocabinet.

[eattach sidetrim.

Remove sidetrim.

Preparation

Excessive Weight Hazard

Use two or more people to move andinstall oven.Failure to follow this instruction canresult in back or other injury.

Important: Use both hands to remove ovendoors.

Do Not use handle or any portion of the frontframe or trim for lifting.Before moving oven across floor, check thatoven is on shipping base or slide oven ontocardboard or hardboard.

Do Not remove shipping feet at the front lowercorners of oven,

Do Not removeshipping feet.

l m Turn power supply off. Move oven

close to final position., Remove and discard shipping materials,

tape and protective film from the oven.Do Not remove shipping base orshipping feet at the front _ower cornersof oven. The shipping feet will protectthe _ower oven trim until oven isinserted into cabinet.

, Remove and set aside racks and otherparts from inside oven.

Remove

oven door.

power X

supply cable X

Removeshippingfeet.

Remove trim$srews.

Remove

oven doors,

Replaceoven doe!

match on the hinge

in locked position =

door free to openand close

latch on the hingein unlocked

position = door

ready for removal

Remove trim screw.Puff trim out,

Pull top of trimdown,

m Completely open oven door. in bothback corners of the door you will see doorlatches in the locked position. Rotate bothlatches forward to the unlocked position.

Grasp outside edges of door with both hands.Begin closing door, at the moment the doorstops closing, lift and puii door toward you.Set door aside on a protective surface.

3u Remove trim screws attaching right

and left side trim to oven. Grasp the bottomend of trim and pull away from oven. Slidetop end of trim downward to remove trimfrom oven. Take care not to scratch othersurfaces with ends of trim. Set trim andscrews aside on protected surface.

Page 2

Electrical connectionIf your house has aluminum wiring, see"Electrical requirements", Page 2.

Electrical 8hock Hazard

Turn power supply off before connecting wires.

Use 8 gauge solid copper wire.

Electrically ground range.Failure to follow these instructions can resultin death, fire, or electrical shock.

This oven is manufactured with white {neutral)power supply wire and a cabinet=connected baregrounding wire twisted together.

Feed oven cable through opening inthe cabinet. Make electrical connection

following the steps needed for your installation.

1. Disconnect the power supply.2. Remove the junction box cover.3. Connect oven cable to junction box through the

U.L.-listed conduit connector.4. Connect the two black wires together with

twist-on connectors.5. Connect the two red wires together with

twist-on connectors.6. Complete electrical connection according to

local codes and ordinances.

black"e8

white

grounding oven U.L.4istedcable wires -- _ conduitfactory crimped cable from connector

Figure 1 oven

ff local codes PERMIT

connecting cabinet-grounding conductor to

neutrat white wire injunction box:

7. Connect the factory-crimpedbare and white oven cable wiresto the neutral (white) wire injunction box. See Figure 1.

8. Replace junction box cover.

cable from power supplyjunctionbox _J--J L

, .= uitFigure 2 cable from connector

oven

If local codes DO NOT

cabinet-groundingconductor to neutram

white wire in

junction box:

7. Separate the factory-crimped bare and whiteoven cable wires.

8. Connect white ovencable wire to neutral(white) wire in junctionbox. See Figure 2.

9. Connect the baregrounding oven cablewire to a grounded wirein the junction box. SeeFigure 2.

10. Replace junction boxcover.

ff connecting to afour-wire electricam

syste m:

7. Separate bare and whiteoven cable wires.

8. Connect white oven cablewire to neutral (white) wirein junction box. SeeFigure 2.

9. Connect the baregrounding oven cable wireto the green groundingwire in junction box.Do Not connect baregrounding wire to neutral{white}wire in junctionbox. See Figure 2.

10. Replace junction boxcover.

AttachmentCarefully push against seal area of ovenfront frame when pushing oven intocabinet.

Do Not push against outside edges.

5m Lift oven into

cob oetcutoutos ngtheoven ope.nmg as an I_',__ I_7/-_

area to gnp

4 screws

Slide topof trim up, !

Push triminto place.Repmacetrim screw.

Slide top end of each trim upward ontooven side rails. Push each trim into place atbottom of trim. Use screws to attach each trim tooven. Take care not to scratch other surfaces withends of trim.

8u Replace oven racks.

/

shippingfoot

Push against seal area of front frame topush oven into cabinet until shipping feetalmost contact cabinet. Use a Phillipsscrewdriver to remove screws attachingshipping feet. Remove and discard shippingfeet.

Push oven completely into cabinet andcenter oven in cabinet cutout.

m important: Securely fasten oven tocabinet using the screws provided (twoscrews for a single oven or four screws for adouble oven). Insert the screws through hobsin mounting rails. Do Not overtighten screws.

g m Reinstall the oven door by inserting

ends of hinges into hinge slots in the ovenframe. Push hinges in as far as theywill go.Open the door (you will feel the door dropinto place) and rotate both hinge latchesback to the locked position.

Close and open the door to check that thedoor closes and opens completely, if doordoes not dose or open completely, repeatthe door removal step and reinstall door asdescribed above.

Repeat for lower oven door.

Check operation

Turn on power supply. Thedisplay panel wiii light up briefly. "PF"should appear in the temperature display.

/ , / , ,f "_i iii

: BAKE BBO& iCLEAN

\ , , / , /m

Check the operation of your single oven.Press the "BROIL" pad. "BROIL" will appearin the display. Press the "START" pad.

Make sure the oven door is closed and the"ON" light is shown in the display area. After2 minutes, partially open oven door. Youshould feel heat from the oven. Press the"CANCEL" pad.

Check the operation of your double oven.Press the "Upper Oven" pad. Pressthe"BROIL" pad. "BROIL" will appear in thedisplay. Pressthe "START" pad. Make surethe oven door is closed and the "ON" light isshown in the display area. After 2 minutes,partially open oven door. You should feel heatfrom the oven. Press the "CANCEL" pad.

Press the "Lower Oven" pad and repeat thesteps you completed for checking the upperoven.

if your oven does not heat or an "F', followed bya number, appears in the disptay, contact yourdealer or check the

"if you need service..." section of this Installationinstructions.

To get the most efficient usefrom your new oven, read your

Use and Care Guide.Keepinstallation instructionsand Guide close to oven

for easy reference.

Page3

ifoven does not

[_ Check that circuit breaker is not tdpped orhouse fuse Nown,

[_ See Use and Care Guide fortrouMeshoofing [[st.

if you need assistance:ff you have questions about operating, cleaningor maintaining your oven:

[_ Refer to Use and Care Guide.

[_ Ca[[the Consumer Assistance Center:Check your Use and Care Guide for a to[[-free number to ca[[ or ca[[ the dealer fromwhom you purchased tMs appliance. Thedealer is listed in the Yellow Pages of yourphone directory under "Appliances --HousehoM -- Major -- Service and Repair."

if you need service:Maintain the qud[ty built into your built-inoven by calling an authorized servicecompany.To obtain the name and number of anauthorized service company:

[_ Contact the dealer from whom youpurchased your bu[[tqn oven; or

[_ Look in the Yellow Pages of your telephonedirectory under "Appliances -- Household-- Major -- Service and Repair" for anauthorized service company; or

[_ Call the Consumer Assistance Center. Thetoll free phone number is listed in your Useand Care Guide.

When you ca[[, you wi[[ need:

[_ The built-in oven mode[ number.

_j The built in oven serial number.Both numbers are listed on the model/serialrating plate, located on the oven door or onthe oven frame.

Part No. 8300651O 2001 Printed in U.S.A.