racal instruments 1260-145 multiplexer plug-in
TRANSCRIPT
RACAL INSTRUMENTS™ 1260-145
MULTIPLEXER PLUG-IN
Publication No. 980824-145 Rev. A
Astronics Test Systems Inc. 4 Goodyear, Irvine, CA 92618
Tel: (800) 722-2528, (949) 859-8999; Fax: (949) 859-7139
[email protected] [email protected] [email protected] http://www.astronicstestsystems.com
Copyright 1998 by Astronics Test Systems Inc. Printed in the United States of America. All rights reserved. This book or parts thereof may not be reproduced in any form without written permission of the publisher.
THANK YOU FOR PURCHASING THIS ASTRONICS TEST SYSTEMS PRODUCT
For this product, or any other Astronics Test Systems product that incorporates software drivers, you may access our web site to verify and/or download the latest driver versions. The web address for driver downloads is:
http://www.astronicstestsystems.com/support/downloads
If you have any questions about software driver downloads or our privacy policy, please contact us at:
WARRANTY STATEMENT
All Astronics Test Systems products are designed to exacting standards and manufactured in full compliance to our AS9100 Quality Management System processes.
This warranty does not apply to defects resulting from any modification(s) of any product or part without Astronics Test Systems express written consent, or misuse of any product or part. The warranty also does not apply to fuses, software, non-rechargeable batteries, damage from battery leakage, or problems arising from normal wear, such as mechanical relay life, or failure to follow instructions.
This warranty is in lieu of all other warranties, expressed or implied, including any implied warranty of merchantability or fitness for a particular use. The remedies provided herein are buyer’s sole and exclusive remedies.
For the specific terms of your standard warranty, contact Customer Support. Please have the following information available to facilitate service.
1. Product serial number 2. Product model number 3. Your company and contact information
You may contact Customer Support by:
E-Mail: [email protected] Telephone: +1 800 722 3262 (USA) Fax: +1 949 859 7139 (USA)
RETURN OF PRODUCT
Authorization is required from Astronics Test Systems before you send us your product or sub-assembly for service or calibration. Call or contact Customer Support at 1-800-722-3262 or 1-949-859-8999 or via fax at 1-949-859-7139. We can also be reached at: [email protected].
If the original packing material is unavailable, ship the product or sub-assembly in an ESD shielding bag and use appropriate packing materials to surround and protect the product.
PROPRIETARY NOTICE
This document and the technical data herein disclosed, are proprietary to Astronics Test Systems, and shall not, without express written permission of Astronics Test Systems, be used in whole or in part to solicit quotations from a competitive source or used for manufacture by anyone other than Astronics Test Systems. The information herein has been developed at private expense, and may only be used for operation and maintenance reference purposes or for purposes of engineering evaluation and incorporation into technical specifications and other documents which specify procurement of products from Astronics Test Systems.
TRADEMARKS AND SERVICE MARKS
All trademarks and service marks used in this document are the property of their respective owners.
• Racal Instruments, Talon Instruments, Trig-Tek, ActivATE, Adapt-A-Switch, N-GEN, and PAWS are trademarks of Astronics Test Systems in the United States.
DISCLAIMER
Buyer acknowledges and agrees that it is responsible for the operation of the goods purchased and should ensure that they are used properly and in accordance with this document and any other instructions provided by Seller. Astronics Test Systems products are not specifically designed, manufactured or intended to be used as parts, assemblies or components in planning, construction, maintenance or operation of a nuclear facility, or in life support or safety critical applications in which the failure of the Astronics Test Systems product could create a situation where personal injury or death could occur. Should Buyer purchase Astronics Test Systems product for such unintended application, Buyer shall indemnify and hold Astronics Test Systems, its officers, employees, subsidiaries, affiliates and distributors harmless against all claims arising out of a claim for personal injury or death associated with such unintended use.
FOR YOUR SAFETY
Before undertaking any troubleshooting, maintenance or exploratory procedure, read carefully the WARNINGS and CAUTION notices.
This equipment contains voltage hazardous to human life and safety, and is capable of inflicting personal injury.
If this instrument is to be powered from the AC line (mains) through an autotransformer, ensure the common connector is connected to the neutral (earth pole) of the power supply.
Before operating the unit, ensure the conductor (green wire) is connected to the ground (earth) conductor of the power outlet. Do not use a two-conductor extension cord or a three-prong/two-prong adapter. This will defeat the protective feature of the third conductor in the power cord.
Maintenance and calibration procedures sometimes call for operation of the unit with power applied and protective covers removed. Read the procedures and heed warnings to avoid “live” circuit points.
Before operating this instrument:
1. Ensure the proper fuse is in place for the power source to operate.
2. Ensure all other devices connected to or in proximity to this instrument are properly grounded or connected to the protective third-wire earth ground.
If the instrument:
- fails to operate satisfactorily - shows visible damage - has been stored under unfavorable conditions - has sustained stress
Do not operate until performance is checked by qualified personnel.
This page was left intentionally blank.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems i
Table of Contents
Chapter 1 .......................................................................................................................... 1-1
MODULE SPECIFICATIONS ........................................................................................................ 1-1
Introduction – 1260-145A (9 – 4x4’s) ............................................................................................ 1-1
Electrical Specifications – 1260-145A ........................................................................................... 1-2
Mechanical Specifications – 1260-145A ........................................................................................ 1-3
Power Dissipation – 1260-145A .................................................................................................... 1-3
Introduction – 1260-145B (3 – 4x12’s) .......................................................................................... 1-4
Electrical Specifications – 1260-145B ........................................................................................... 1-5
Mechanical Specifications – 1260-145B ........................................................................................ 1-6
Power Dissipation – 1260-145B .................................................................................................... 1-6
Introduction – 1260-145C (2 – 4x16’s) .......................................................................................... 1-7
Electrical Specifications – 1260-145C ........................................................................................... 1-8
Mechanical Specifications – 1260-145C ....................................................................................... 1-9
Power Dissipation – 1260-145C .................................................................................................... 1-9
Introduction – 1260-145D (1 – 4x36) ........................................................................................... 1-10
Electrical Specifications – 1260-145D ......................................................................................... 1-11
Mechanical Specifications – 1260-145D ..................................................................................... 1-12
Power Dissipation – 1260-145D .................................................................................................. 1-12
Introduction – 1260-145E (2 – 8x8’s) .......................................................................................... 1-13
Electrical Specifications – 1260-145E ......................................................................................... 1-14
Mechanical Specifications – 1260-145E ...................................................................................... 1-15
Power Dissipation – 1260-145E .................................................................................................. 1-15
Introduction – 1260-145F (1 – 8x16) ........................................................................................... 1-16
1260-145 User Manual Publication No. 980824-145 Rev. A
ii Astronics Test Systems
Electrical Specifications – 1260-145F ......................................................................................... 1-17
Mechanical Specifications – 1260-145F ...................................................................................... 1-18
Power Dissipation – 1260-145F .................................................................................................. 1-18
Introduction – 1260-145G (1 – 12x12) ........................................................................................ 1-19
Electrical Specifications – 1260-145G ........................................................................................ 1-20
Mechanical Specifications – 1260-145G ..................................................................................... 1-21
Power Dissipation – 1260-145G ................................................................................................. 1-21
About MTBF ............................................................................................................................... 1-22
Ordering Information ................................................................................................................... 1-23
Chapter 2 ........................................................................................................................... 2-1
INSTALLATION INSTRUCTIONS ................................................................................................ 2-1
Unpacking and Inspection ............................................................................................................ 2-1
Installation .................................................................................................................................... 2-2
Module Configuration .................................................................................................................... 2-2
Front Panel Connectors ................................................................................................................ 2-2
Mating Connectors ........................................................................................................................ 2-3
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems iii
Chapter 3 ........................................................................................................................... 3-1
MODULE OPERATION ................................................................................................................. 3-1
Setting the Module Address .......................................................................................................... 3-1
Operating Modes .......................................................................................................................... 3-2
Operating In Message-Based Mode .............................................................................................. 3-4
Channel Descriptors For The 1260-145 ........................................................................................ 3-4
Reply To The MOD:LIST? Command ........................................................................................... 3-5
Operating The 1260-145 in Register-Based Mode ........................................................................ 3-6
1260-145 Example Code ............................................................................................................ 3-17
Chapter 4 ........................................................................................................................... 4-1
OPTIONAL ASSEMBLIES ............................................................................................................ 4-1
1260-145 User Manual Publication No. 980824-145 Rev. A
iv Astronics Test Systems
This page was left intentionally blank.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems v
List of Figures Figure 1-1, The 1260-145 Series .................................................................................................. 1-1
Figure 2-1, Front-Panel Connector Pin Numbering ....................................................................... 2-2
Figure 2-2, 1260-145 Block Diagram ............................................................................................ 2-3
Figure 3-1, Message-Based Mode of Operation ........................................................................... 3-3
Figure 3-2, Register-Based Mode of Operation ............................................................................. 3-3
Figure 3-3, Numbering Nomenclature for all 1260-145 Variants ................................................... 3-8
Figure 3-4, Message-Based Channel Descriptor to Physical Switch Orientation ........................... 3-9
Figure 3-5, 1260-145A Connector/Channel Organization ............................................................ 3-10
Figure 3-6, 1260-145B Connector/Channel Organization ............................................................ 3-11
Figure 3-7, 1260-145C Connector/Channel Organization ........................................................... 3-12
Figure 3-8, 1260-145D Connector/Channel Organization ........................................................... 3-13
Figure 3-9, 1260-145E Connector/Channel Organization ............................................................ 3-14
Figure 3-10, 1260-145F Connector/Channel Organization .......................................................... 3-15
Figure 3-11, 1260-145G Connector/Channel Organization ......................................................... 3-16
1260-145 User Manual Publication No. 980824-145 Rev. A
vi Astronics Test Systems
DOCUMENT CHANGE HISTORY
Revision Date Description of Change
A 8/12/08
Revised per EO 29827 Revised format to current standards. Company name revised throughout manual. Manual now revision letter controlled. Added Document Change History Page v.
No change 03/24/09
Back of cover sheet. Revised Warranty Statement, Return of Product, Proprietary Notice and Disclaimer to current standards. Removed Reshipment Instructions in (Chap. 2-1) and removed (Chap 5). Information. Now appears in first 2 sheets behind cover sheet. Updated table of contents to reflect changes made. . Added company name to footer at lower corner opposite of Page no’s i thru vi.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-1
Chapter 1 MODULE SPECIFICATIONS
Introduction – 1260-145A (9 – 4x4’s)
The 1260-145A is a plug-in matrix switch module developed for the 1260-100 Adapt-a-Switch Carrier. This switch provides nine independent 4x4 matrices with a maximum switching voltage of 125VAC @ 0.3A or 30 VDC @ 1A.
The 1260-145A includes the following features:
• Standard Adapt-a-Switch plug-in design, providing for ease of replacement
• Data-Driven embedded descriptor, allowing immediate use with any Option-01T switch controller, regardless of firmware revision level.
Figure 1-1, The 1260-145 Series
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-2 Astronics Test Systems
Electrical Specifications – 1260-145A
Chan. Input Voltage 60 VDC / 125 VAC maximum
Chan. Output Current 1 A maximum
Chan. Output Power 30 W / 37.5 VA maximum
Path Resistance < 1.8 Ohms (HI + LOW path)
Contact Bounce Time 3 ms maximum
Contact Thermal EMF 4 µV maximum
Switch Contact Lifetime 50 Million Cycles (low-level) 100,000 Cycles (maximum rating)
Available I/O Channels 144 (dual wire)
Capacitance A (HI) to B (LOW) 120 pF maximum Chan. to Chassis 415 pF maximum
Bandwidth 42 MHz (-3 dB) minimum (Worst Path Performance; Typical Unit)
Insertion Loss 1.0 dB @ 10 MHz maximum (Worst Path Performance; 0.2 dB @ 1 MHz maximum Typical Unit) 0.1 dB @ 300 kHz maximum
Isolation 15 dB @ 42 MHz minimum (Worst Path Performance; 43 dB @ 10 MHz minimum Typical Unit) 62 dB @ 1 MHz minimum 76 dB @ 300 kHz minimum
Crosstalk -9 dB @ 42 MHz maximum (Worst Path Performance; -49 dB @ 10 MHz maximum Typical Unit) -69 dB @ 1 MHz maximum -81 dB @ 300 kHz maximum
Power Requirements +5 VDC quiescent 0.1 A maximum each relay closure 0.02 A maximum
Mean Time Between 33,784 Hours (MIL-HDBK-217FN2) Failures (MTBF) 50,714 Hours (Telcordia / Bellcore 6)
Mean Time to Repair < 5 minutes (MTTR)
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-3
Mechanical Specifications – 1260-145A
Shock 30g, 11 ms, ½ sine wave
Vibration 0.013 in. P-P, 5-55 Hz
Bench Handling 4 in., 45°
Cooling See 1260-100 cooling data
Temperature Operating 0°C to +55°C Non-operating -40°C to +75°C
Relative Humidity 85% + 5% non-condensing at < 30°C
Altitude Operating 10,000 feet Non-operating 15,000 feet
Weight 9 oz. (0.32 kg.)
Power Dissipation – 1260-145A
The cooling of the Adapt-a-Switch carrier is dependent upon the chassis into which it is installed. The carrier can nominally dissipate approximately 100W. Even with all channels driven to maximum outputs, up to six 1260-145A plug-ins may be used together in a 1260-100 without exceeding the maximum allowable power dissipation of the carrier.
If the 1260-145A will be used in conjunction with other cards, the dissipation should be computed and summed with the total worst-case dissipation of the remaining modules.
For example, a 1260-145A module would dissipate the following energy:
Quiescent power dissipation = 0.5W maximum
Channel dissipation = [(# channels energized) * (relay coil dissipation)]
Total Power Dissipation = Quiescent + Channel
Assuming all relays on the card are enabled (worse-case situation) the channel path resistances will be in parallel and therefore insignificant as a source of heat. The largest contributor of thermal energy will therefore derive from the relay coils.
Total power dissipation = [(144) * (0.100)] + [0.5] = 15W
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-4 Astronics Test Systems
This is acceptable power dissipation for an individual plug-in module. If five additional modules are likewise loaded, then the overall carrier dissipation is approximately 90W, which is within the cooling available in most commercial VXIbus chassis. Apart from the thermal issues, however, it is important to remember that a fully enabled 1260-145A card would draw over 3A of current from the +5V supply. If this is multiplied by six for the remaining slots, a load of 18A would burden the +5V supply, exceeding the specifications for the 1260-100 carrier. In reality, the worse-case situation is not likely, since the 1260-145A is a matrix switch where typically only one relay is engaged at a time and the power dissipation falls considerably below that calculated in the example above. For practical purposes, as the calculations can illustrate for normal operation, the 1260-145A contributes a negligible amount of thermal load on a chassis.
Introduction – 1260-145B (3 – 4x12’s)
The 1260-145B is a plug-in matrix switch module developed for the 1260-100 Adapt-a-Switch Carrier. This switch provides three independent 4x12 matrices with a maximum switching voltage of 125VAC @ 0.3A or 30 VDC @ 1A.
The 1260-145B includes the following features:
• Standard Adapt-a-Switch plug-in design, providing for ease of replacement
• Data-Driven embedded descriptor, allowing immediate use with any Option-01T switch controller, regardless of firmware revision level.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-5
Electrical Specifications – 1260-145B
Chan. Input Voltage 60 VDC / 125 VAC maximum
Chan. Output Current 1 A maximum
Chan. Output Power 30 W / 37.5 VA maximum
Path Resistance < 1.4 Ohms (HI + LOW path)
Contact Bounce Time 3 ms maximum
Contact Thermal EMF 4 µV maximum
Switch Contact Lifetime 50 Million Cycles (low-level) 100,000 Cycles (maximum rating)
Available I/O Channels 144 (dual wire)
Capacitance A (HI) to B (LOW) 135 pF maximum Chan. to Chassis 500 pF maximum
Bandwidth 31 MHz (-3 dB) minimum (Worst Path Performance; Typical Unit)
Insertion Loss 0.5 dB @ 10 MHz maximum (Worst Path Performance; 0.1 dB @ 1 MHz maximum Typical Unit) 0.1 dB @ 300 kHz maximum
Isolation 22 dB @ 31 MHz minimum (Worst Path Performance; 52 dB @ 10 MHz minimum Typical Unit) 68 dB @ 1 MHz minimum 75 dB @ 300 kHz minimum
Crosstalk -16 dB @ 31 MHz maximum (Worst Path Performance; -49 dB @ 10 MHz maximum Typical Unit) -70 dB @ 1 MHz maximum -72 dB @ 300 kHz maximum
Power Requirements +5 VDC quiescent 0.1 A maximum each relay closure 0.02 A maximum
Mean Time Between 33,773 Hours (MIL-HDBK-217FN2) Failures (MTBF) 50,687 Hours (Telcordia / Bellcore 6)
Mean Time to Repair < 5 minutes (MTTR)
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-6 Astronics Test Systems
Mechanical Specifications – 1260-145B
Shock 30g, 11 ms, ½ sine wave
Vibration 0.013 in. P-P, 5-55 Hz
Bench Handling 4 in., 45°
Cooling See 1260-100 cooling data
Temperature Operating 0°C to +55°C Non-operating -40°C to +75°C
Relative Humidity 85% + 5% non-condensing at < 30°C
Altitude Operating 10,000 feet Non-operating 15,000 feet
Weight 9 oz. (0.32 kg.)
Power Dissipation – 1260-145B
The cooling of the Adapt-a-Switch carrier is dependent upon the chassis into which it is installed. The carrier can nominally dissipate approximately 100W. Even with all channels driven to maximum outputs, up to six 1260-145B plug-ins may be used together in a 1260-100 without exceeding the maximum allowable power dissipation of the carrier.
If the 1260-145B will be used in conjunction with other cards, the dissipation should be computed and summed with the total worst-case dissipation of the remaining modules.
For example, a 1260-145B module would dissipate the following energy:
Quiescent power dissipation = 0.5W maximum
Channel dissipation = [(# channels energized) * (relay coil dissipation)]
Total Power Dissipation = Quiescent + Channel
Assuming all relays on the card are enabled (worse-case situation) the channel path resistances will be in parallel and therefore insignificant as a source of heat. The largest contributor of thermal energy will therefore derive from the relay coils.
Total power dissipation = [(144) * (0.100)] + [0.5] = 15W
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-7
This is acceptable power dissipation for an individual plug-in module. If five additional modules are likewise loaded, then the overall carrier dissipation is approximately 90W, which is within the cooling available in most commercial VXIbus chassis. Apart from the thermal issues, however, it is important to remember that a fully enabled 1260-145B card would draw over 3A of current from the +5V supply. If this is multiplied by six for the remaining slots, a load of 18A would burden the +5V supply, exceeding the specifications for the 1260-100 carrier. In reality, the worse-case situation is not likely, since the 1260-145B is a matrix switch where typically only one relay is engaged at a time and the power dissipation falls considerably below that calculated in the example above. For practical purposes, as the calculations can illustrate for normal operation, the 1260-145B contributes a negligible amount of thermal load on a chassis.
Introduction – 1260-145C (2 – 4x16’s)
The 1260-145C is a plug-in matrix switch module developed for the 1260-100 Adapt-a-Switch Carrier. This switch provides two independent 4x16 matrices with a maximum switching voltage of 125VAC @ 0.3A or 30 VDC @ 1A.
The 1260-145C includes the following features:
• Standard Adapt-a-Switch plug-in design, providing for ease of replacement
• Data-Driven embedded descriptor, allowing immediate use with any Option-01T switch controller, regardless of firmware revision level.
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-8 Astronics Test Systems
Electrical Specifications – 1260-145C
Chan. Input Voltage 60 VDC / 125 VAC maximum
Chan. Output Current 1 A maximum
Chan. Output Power 30 W / 37.5 VA maximum
Path Resistance < 1.6 Ohms (HI + LOW path)
Contact Bounce Time 3 ms maximum
Contact Thermal EMF 4 µV maximum
Switch Contact Lifetime 50 Million Cycles (low-level) 100,000 Cycles (maximum rating)
Available I/O Channels 128 (dual wire)
Capacitance A (HI) to B (LOW) 175 pF maximum Chan. to Chassis 640 pF maximum
Bandwidth 24 MHz (-3 dB) minimum (Worst Path Performance; Typical Unit)
Insertion Loss 0.8 dB @ 10 MHz maximum (Worst Path Performance; 0.1 dB @ 1 MHz maximum Typical Unit) 0.1 dB @ 300 kHz maximum
Isolation 37 dB @ 24 MHz minimum (Worst Path Performance; 48 dB @ 10 MHz minimum Typical Unit) 67 dB @ 1 MHz minimum 77 dB @ 300 kHz minimum
Crosstalk -19 dB @ 24 MHz maximum (Worst Path Performance; -46 dB @ 10 MHz maximum Typical Unit) -59 dB @ 1 MHz maximum -63 dB @ 300 kHz maximum
Power Requirements +5 VDC quiescent 0.1 A maximum each relay closure 0.02 A maximum
Mean Time Between 37,908 Hours (MIL-HDBK-217FN2) Failures (MTBF) 56,705 Hours (Telcordia / Bellcore 6)
Mean Time to Repair < 5 minutes (MTTR)
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-9
Mechanical Specifications – 1260-145C
Shock 30g, 11 ms, ½ sine wave
Vibration 0.013 in. P-P, 5-55 Hz
Bench Handling 4 in., 45°
Cooling See 1260-100 cooling data
Temperature Operating 0°C to +55°C Non-operating -40°C to +75°C
Relative Humidity 85% + 5% non-condensing at < 30°C
Altitude Operating 10,000 feet Non-operating 15,000 feet
Weight 9 oz. (0.32 kg.)
Power Dissipation – 1260-145C
The cooling of the Adapt-a-Switch carrier is dependent upon the chassis into which it is installed. The carrier can nominally dissipate approximately 100W. Even with all channels driven to maximum outputs, up to six 1260-145C plug-ins may be used together in a 1260-100 without exceeding the maximum allowable power dissipation of the carrier.
If the 1260-145C will be used in conjunction with other cards, the dissipation should be computed and summed with the total worst-case dissipation of the remaining modules.
For example, a 1260-145C module would dissipate the following energy:
Quiescent power dissipation = 0.5W maximum
Channel dissipation = [(# channels energized) * (relay coil dissipation)]
Total Power Dissipation = Quiescent + Channel
Assuming all relays on the card are enabled (worse-case situation) the channel path resistances will be in parallel and therefore insignificant as a source of heat. The largest contributor of thermal energy will therefore derive from the relay coils.
Total power dissipation = [(128) * (0.100)] + [0.5] = 13.3W
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-10 Astronics Test Systems
This is acceptable power dissipation for an individual plug-in module. If five additional modules are likewise loaded, then the overall carrier dissipation is approximately 80W, which is within the cooling available in most commercial VXIbus chassis. Apart from the thermal issues, however, it is important to remember that a fully enabled 1260-145C card would draw over 2.7A of current from the +5V supply. If this is multiplied by six for the remaining slots, a load of 16A would burden the +5V supply, exceeding the specifications for the 1260-100 carrier. In reality, the worse-case situation is not likely, since the 1260-145C is a matrix switch where typically only one relay is engaged at a time and the power dissipation falls considerably below that calculated in the example above. For practical purposes, as the calculations can illustrate for normal operation, the 1260-145C contributes a negligible amount of thermal load on a chassis.
Introduction – 1260-145D (1 – 4x36)
The 1260-145D is a plug-in matrix switch module developed for the 1260-100 Adapt-a-Switch Carrier. This switch provides a 4x36 matrix with a maximum switching voltage of 125VAC @ 0.3A or 30 VDC @ 1A.
The 1260-145D includes the following features:
• Standard Adapt-a-Switch plug-in design, providing for ease of replacement
• Data-Driven embedded descriptor, allowing immediate use with any Option-01T switch controller, regardless of firmware revision level.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-11
Electrical Specifications – 1260-145D
Chan. Input Voltage 60 VDC / 125 VAC maximum
Chan. Output Current 1 A maximum
Chan. Output Power 30 W / 37.5 VA maximum
Path Resistance < 1.6 Ohms (HI + LOW path)
Contact Bounce Time 3 ms maximum
Contact Thermal EMF 4 µV maximum
Switch Contact Lifetime 50 Million Cycles (low-level) 100,000 Cycles (maximum rating)
Available I/O Channels 144 (dual wire)
Capacitance A (HI) to B (LOW) 310 pF maximum Chan. to Chassis 1485 pF maximum
Bandwidth 13 MHz (-3 dB) minimum (Worst Path Performance; Typical Unit)
Insertion Loss 2.0 dB @ 10 MHz maximum (Worst Path Performance; 0.1 dB @ 1 MHz maximum Typical Unit) 0.1 dB @ 300 kHz maximum Isolation 37 dB @ 13 MHz minimum (Worst Path Performance; 44 dB @ 10 MHz minimum Typical Unit) 67 dB @ 1 MHz minimum 75 dB @ 300 kHz minimum
Crosstalk -38 dB @ 13 MHz maximum (Worst Path Performance; -42 dB @ 10 MHz maximum Typical Unit) -68 dB @ 1 MHz maximum -75 dB @ 300 kHz maximum
Power Requirements +5 VDC quiescent 0.1 A maximum each relay closure 0.02 A maximum
Mean Time Between 33,768 Hours (MIL-HDBK-217FN2) Failures (MTBF) 50,673 Hours (Telcordia / Bellcore 6)
Mean Time to Repair < 5 minutes (MTTR)
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-12 Astronics Test Systems
Mechanical Specifications – 1260-145D
Shock 30g, 11 ms, ½ sine wave
Vibration 0.013 in. P-P, 5-55 Hz
Bench Handling 4 in., 45°
Cooling See 1260-100 cooling data
Temperature Operating 0°C to +55°C Non-operating -40°C to +75°C
Relative Humidity 85% + 5% non-condensing at < 30°C
Altitude Operating 10,000 feet Non-operating 15,000 feet
Weight 9 oz. (0.32 kg.)
Power Dissipation – 1260-145D
The cooling of the Adapt-a-Switch carrier is dependent upon the chassis into which it is installed. The carrier can nominally dissipate approximately 100W. Even with all channels driven to maximum outputs, up to six 1260-145D plug-ins may be used together in a 1260-100 without exceeding the maximum allowable power dissipation of the carrier.
If the 1260-145D will be used in conjunction with other cards, the dissipation should be computed and summed with the total worst-case dissipation of the remaining modules.
For example, a 1260-145D module would dissipate the following energy:
Quiescent power dissipation = 0.5W maximum
Channel dissipation = [(# channels energized) * (relay coil dissipation)]
Total Power Dissipation = Quiescent + Channel
Assuming all relays on the card are enabled (worse-case situation) the channel path resistances will be in parallel and therefore insignificant as a source of heat. The largest contributor of thermal energy will therefore derive from the relay coils.
Total power dissipation = [(144) * (0.100)] + [0.5] = 15W
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-13
This is acceptable power dissipation for an individual plug-in module. If five additional modules are likewise loaded, then the overall carrier dissipation is approximately 90W, which is within the cooling available in most commercial VXIbus chassis. Apart from the thermal issues, however, it is important to remember that a fully enabled 1260-145D card would draw over 3A of current from the +5V supply. If this is multiplied by six for the remaining slots, a load of 18A would burden the +5V supply, exceeding the specifications for the 1260-100 carrier. In reality, the worse-case situation is not likely, since the 1260-145D is a matrix switch where typically only one relay is engaged at a time and the power dissipation falls considerably below that calculated in the example above. For practical purposes, as the calculations can illustrate for normal operation, the 1260-145D contributes a negligible amount of thermal load on a chassis.
Introduction – 1260-145E (2 – 8x8’s)
The 1260-145E is a plug-in matrix switch module developed for the 1260-100 Adapt-a-Switch Carrier. This switch provides two independent 8x8 matrices with a maximum switching voltage of 125VAC @ 0.3A or 30 VDC @ 1A.
The 1260-145E includes the following features:
• Standard Adapt-a-Switch plug-in design, providing for ease of replacement
• Data-Driven embedded descriptor, allowing immediate use with any Option-01T switch controller, regardless of firmware revision level.
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-14 Astronics Test Systems
Electrical Specifications – 1260-145E
Chan. Input Voltage 60 VDC / 125 VAC maximum
Chan. Output Current 1 A maximum
Chan. Output Power 30 W / 37.5 VA maximum
Path Resistance < 2 Ohms (HI + LOW path)
Contact Bounce Time 3 ms maximum
Contact Thermal EMF 4 µV maximum
Switch Contact Lifetime 50 Million Cycles (low-level) 100,000 Cycles (maximum rating)
Available I/O Channels 128 (dual wire)
Capacitance A (HI) to B (LOW) 175 pF maximum Chan. to Chassis 640 pF maximum
Bandwidth 27 MHz (-3 dB) minimum (Worst Path Performance; Typical Unit)
Insertion Loss 0.7 dB @ 10 MHz maximum (Worst Path Performance; 0.2 dB @ 1 MHz maximum Typical Unit) 0.1 dB @ 300 kHz maximum
Isolation 29 dB @ 27 MHz minimum (Worst Path Performance; 43 dB @ 10 MHz minimum Typical Unit) 61 dB @ 1 MHz minimum 74 dB @ 300 kHz minimum
Crosstalk -15 dB @ 27 MHz maximum (Worst Path Performance; -46 dB @ 10 MHz maximum Typical Unit) -64 dB @ 1 MHz maximum -72 dB @ 300 kHz maximum
Power Requirements +5 VDC quiescent 0.1 A maximum each relay closure 0.02 A maximum
Mean Time Between 37,904 Hours (MIL-HDBK-217FN2) Failures (MTBF) 56,694 Hours (Telcordia / Bellcore 6)
Mean Time to Repair < 5 minutes (MTTR)
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-15
Mechanical Specifications – 1260-145E
Shock 30g, 11 ms, ½ sine wave
Vibration 0.013 in. P-P, 5-55 Hz
Bench Handling 4 in., 45°
Cooling See 1260-100 cooling data
Temperature Operating 0°C to +55°C Non-operating -40°C to +75°C
Relative Humidity 85% + 5% non-condensing at < 30°C
Altitude Operating 10,000 feet Non-operating 15,000 feet
Weight 9 oz. (0.32 kg.)
Power Dissipation – 1260-145E
The cooling of the Adapt-a-Switch carrier is dependent upon the chassis into which it is installed. The carrier can nominally dissipate approximately 100W. Even with all channels driven to maximum outputs, up to six 1260-145E plug-ins may be used together in a 1260-100 without exceeding the maximum allowable power dissipation of the carrier.
If the 1260-145E will be used in conjunction with other cards, the dissipation should be computed and summed with the total worst-case dissipation of the remaining modules.
For example, a 1260-145E module would dissipate the following energy:
Quiescent power dissipation = 0.5W maximum
Channel dissipation = [(# channels energized) * (relay coil dissipation)]
Total Power Dissipation = Quiescent + Channel
Assuming all relays on the card are enabled (worse-case situation) the channel path resistances will be in parallel and therefore insignificant as a source of heat. The largest contributor of thermal energy will therefore derive from the relay coils.
Total power dissipation = [(128) * (0.100)] + [0.5] = 13.3W
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-16 Astronics Test Systems
This is acceptable power dissipation for an individual plug-in module. If five additional modules are likewise loaded, then the overall carrier dissipation is approximately 80W, which is within the cooling available in most commercial VXIbus chassis. Apart from the thermal issues, however, it is important to remember that a fully enabled 1260-145E card would draw over 2.7A of current from the +5V supply. If this is multiplied by six for the remaining slots, a load of 16A would burden the +5V supply, exceeding the specifications for the 1260-100 carrier. In reality, the worse-case situation is not likely, since the 1260-145E is a matrix switch where typically only one relay is engaged at a time and the power dissipation falls considerably below that calculated in the example above. For practical purposes, as the calculations can illustrate for normal operation, the 1260-145E contributes a negligible amount of thermal load on a chassis.
Introduction – 1260-145F (1 – 8x16)
The 1260-145F is a plug-in matrix switch module developed for the 1260-100 Adapt-a-Switch Carrier. This switch provides a 8x16 matrix with a maximum switching voltage of 125VAC @ 0.3A or 30 VDC @ 1A.
The 1260-145F includes the following features:
• Standard Adapt-a-Switch plug-in design, providing for ease of replacement
• Data-Driven embedded descriptor, allowing immediate use with any Option-01T switch controller, regardless of firmware revision level.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-17
Electrical Specifications – 1260-145F
Chan. Input Voltage 60 VDC / 125 VAC maximum
Chan. Output Current 1 A maximum
Chan. Output Power 30 W / 37.5 VA maximum
Path Resistance < 1.8 Ohms (HI + LOW path)
Contact Bounce Time 3 ms maximum
Contact Thermal EMF 4 µV maximum
Switch Contact Lifetime 50 Million Cycles (low-level) 100,000 Cycles (maximum rating)
Available I/O Channels 128 (dual wire)
Capacitance A (HI) to B (LOW) 225 pF maximum Chan. to Chassis 840 pF maximum
Bandwidth 20 MHz (-3 dB) minimum (Worst Path Performance; Typical Unit)
Insertion Loss 1.2 dB @ 10 MHz maximum (Worst Path Performance; 0.2 dB @ 1 MHz maximum Typical Unit) 0.1 dB @ 300 kHz maximum
Isolation 30 dB @ 20 MHz minimum (Worst Path Performance; 53 dB @ 10 MHz minimum Typical Unit) 66 dB @ 1 MHz minimum 79 dB @ 300 kHz minimum
Crosstalk -30 dB @ 20 MHz maximum (Worst Path Performance; -44 dB @ 10 MHz maximum Typical Unit) -62 dB @ 1 MHz maximum -77 dB @ 300 kHz maximum
Power Requirements +5 VDC quiescent 0.1 A maximum each relay closure 0.02 A maximum
Mean Time Between 37,899 Hours (MIL-HDBK-217FN2) Failures (MTBF) 56,682 Hours (Telcordia / Bellcore 6)
Mean Time to Repair < 5 minutes (MTTR)
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-18 Astronics Test Systems
Mechanical Specifications – 1260-145F
Shock 30g, 11 ms, ½ sine wave
Vibration 0.013 in. P-P, 5-55 Hz
Bench Handling 4 in., 45°
Cooling See 1260-100 cooling data
Temperature Operating 0°C to +55°C Non-operating -40°C to +75°C
Relative Humidity 85% + 5% non-condensing at < 30°C
Altitude Operating 10,000 feet Non-operating 15,000 feet
Weight 9 oz. (0.32 kg.)
Power Dissipation – 1260-145F
The cooling of the Adapt-a-Switch carrier is dependent upon the chassis into which it is installed. The carrier can nominally dissipate approximately 100W. Even with all channels driven to maximum outputs, up to six 1260-145F plug-ins may be used together in a 1260-100 without exceeding the maximum allowable power dissipation of the carrier.
If the 1260-145F will be used in conjunction with other cards, the dissipation should be computed and summed with the total worst-case dissipation of the remaining modules.
For example, a 1260-145F module would dissipate the following energy:
Quiescent power dissipation = 0.5W maximum
Channel dissipation = [(# channels energized) * (relay coil dissipation)]
Total Power Dissipation = Quiescent + Channel
Assuming all relays on the card are enabled (worse-case situation) the channel path resistances will be in parallel and therefore insignificant as a source of heat. The largest contributor of thermal energy will therefore derive from the relay coils.
Total power dissipation = [(128) * (0.100)] + [0.5] = 13.3W
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-19
This is acceptable power dissipation for an individual plug-in module. If five additional modules are likewise loaded, then the overall carrier dissipation is approximately 80W, which is within the cooling available in most commercial VXIbus chassis. Apart from the thermal issues, however, it is important to remember that a fully enabled 1260-145F card would draw over 2.7A of current from the +5V supply. If this is multiplied by six for the remaining slots, a load of 16A would burden the +5V supply, exceeding the specifications for the 1260-100 carrier. In reality, the worse-case situation is not likely, since the 1260-145F is a matrix switch where typically only one relay is engaged at a time and the power dissipation falls considerably below that calculated in the example above. For practical purposes, as the calculations can illustrate for normal operation, the 1260-145F contributes a negligible amount of thermal load on a chassis.
Introduction – 1260-145G (1 – 12x12)
The 1260-145G is a plug-in matrix switch module developed for the 1260-100 Adapt-a-Switch Carrier. This switch provides a 12x12 matrix with a maximum switching voltage of 125VAC @ 0.3A or 30 VDC @ 1A.
The 1260-145G includes the following features:
• Standard Adapt-a-Switch plug-in design, providing for ease of replacement
• Data-Driven embedded descriptor, allowing immediate use with any Option-01T switch controller, regardless of firmware revision level.
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-20 Astronics Test Systems
Electrical Specifications – 1260-145G
Chan. Input Voltage 60 VDC / 125 VAC maximum
Chan. Output Current 1 A maximum
Chan. Output Power 30 W / 37.5 VA maximum
Path Resistance < 1.5 Ohms (HI + LOW path)
Contact Bounce Time 3 ms maximum
Contact Thermal EMF 4 µV maximum
Switch Contact Lifetime 50 Million Cycles (low-level) 100,000 Cycles (maximum rating)
Available I/O Channels 144 (dual wire)
Capacitance A (HI) to B (LOW) 175 pF maximum Chan. to Chassis 625 pF maximum
Bandwidth 27 MHz (-3 dB) minimum (Worst Path Performance; Typical Unit)
Insertion Loss 0.7 dB @ 10 MHz maximum (Worst Path Performance; 0.1 dB @ 1 MHz maximum Typical Unit) 0.1 dB @ 300 kHz maximum
Isolation 24 dB @ 27 MHz minimum (Worst Path Performance; 52 dB @ 10 MHz minimum Typical Unit) 67 dB @ 1 MHz minimum 74 dB @ 300 kHz minimum
Crosstalk -28 dB @ 27 MHz maximum (Worst Path Performance; -44 dB @ 10 MHz maximum Typical Unit) -65 dB @ 1 MHz maximum -70 dB @ 300 kHz maximum
Power Requirements +5 VDC quiescent 0.1 A maximum each relay closure 0.02 A maximum
Mean Time Between 33,763 Hours (MIL-HDBK-217FN2) Failures (MTBF) 50,660 Hours (Telcordia / Bellcore 6)
Mean Time to Repair < 5 minutes (MTTR)
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-21
Mechanical Specifications – 1260-145G
Shock 30g, 11 ms, ½ sine wave
Vibration 0.013 in. P-P, 5-55 Hz
Bench Handling 4 in., 45°
Cooling See 1260-100 cooling data
Temperature Operating 0°C to +55°C Non-operating -40°C to +75°C
Relative Humidity 85% + 5% non-condensing at < 30°C
Altitude Operating 10,000 feet Non-operating 15,000 feet
Weight 9 oz. (0.32 kg.)
Power Dissipation – 1260-145G
The cooling of the Adapt-a-Switch carrier is dependent upon the chassis into which it is installed. The carrier can nominally dissipate approximately 100W. Even with all channels driven to maximum outputs, up to six 1260-145G plug-ins may be used together in a 1260-100 without exceeding the maximum allowable power dissipation of the carrier.
If the 1260-145G will be used in conjunction with other cards, the dissipation should be computed and summed with the total worst-case dissipation of the remaining modules.
For example, a 1260-145G module would dissipate the following energy:
Quiescent power dissipation = 0.5W maximum
Channel dissipation = [(# channels energized) * (relay coil dissipation)]
Total Power Dissipation = Quiescent + Channel
Assuming all relays on the card are enabled (worse-case situation) the channel path resistances will be in parallel and therefore insignificant as a source of heat. The largest contributor of thermal energy will therefore derive from the relay coils.
Total power dissipation = [(144) * (0.100)] + [0.5] = 15W
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-22 Astronics Test Systems
This is acceptable power dissipation for an individual plug-in module. If five additional modules are likewise loaded, then the overall carrier dissipation is approximately 90W, which is within the cooling available in most commercial VXIbus chassis. Apart from the thermal issues, however, it is important to remember that a fully enabled 1260-145G card would draw over 3A of current from the +5V supply. If this is multiplied by six for the remaining slots, a load of 18A would burden the +5V supply, exceeding the specifications for the 1260-100 carrier. In reality, the worse-case situation is not likely, since the 1260-145G is a matrix switch where typically only one relay is engaged at a time and the power dissipation falls considerably below that calculated in the example above. For practical purposes, as the calculations can illustrate for normal operation, the 1260-145G contributes a negligible amount of thermal load on a chassis.
About MTBF The 1260-145 MTBF is calculated in accordance with MIL-HDBK-217FN2 and Telcordia (Bellcore) 6 procedures. Refer to the specifications for each card for calculated MTBF values.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Specifications 1-23
Ordering Information
Listed below are part numbers for both the 1260-145 switch module and available mating connector accessories. Each 1260-145 uses a single mating connector.
ITEM DESCRIPTION PART # 1260-145A Switch Module 1260-145A, 9 4x4 Matrix Switch
Consists of: P/N 405139-001 PCB Assy P/N 980824-145 Manual
407643-001
1260-145B Switch Module 1260-145B, 3 4x12 Matrix Switch Consists of: P/N 405139-002 PCB Assy P/N 980824-145 Manual
407643-002
1260-145C Switch Module 1260-145C, 2 4x16 Matrix Switch Consists of: P/N 405139-003 PCB Assy P/N 980824-145 Manual
407643-003
1260-145D Switch Module 1260-145D, 1 4x36 Matrix Switch Consists of: P/N 405139-004 PCB Assy P/N 980824-145 Manual
407643-004
1260-145E Switch Module 1260-145E, 2 8x8 Matrix Switch Consists of: P/N 405139-005 PCB Assy P/N 980824-145 Manual
407643-005
1260-145F Switch Module 1260-145F, 1 8x16 Matrix Switch Consists of: P/N 405139-006 PCB Assy P/N 980824-145 Manual
407643-006
1260-145G Switch Module 1260-145G, 3 4x12 Matrix Switch Consists of: P/N 405139-007 PCB Assy P/N 980824-145 Manual
407643-007
160-pin Mating Connector 160 Pin Conn. Kit with pins 407664 Cable Assy. 6ft, Sleeved 160 Pin Cable Assy, 6 Ft, 24 AWG 407408-001 Connector Bracket Bracket, Strain Relief 456673 Additional Manual 980824-145
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Specifications 1-24 Astronics Test Systems
This page was left intentionally blank.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Installation Instructions 2-1
Chapter 2 INSTALLATION INSTRUCTIONS
Unpacking and Inspection
1. Remove the 1260-145 module and inspect it for damage. If any damage is apparent, inform the carrier immediately. Retain shipping carton and packing material for the carrier’s inspection.
2. Verify that the pieces in the package you received contain the correct 1260-145 module option and the 1260-145 Users Manual. Notify Customer Support if the module appears damaged in any way. Do not attempt to install a damaged module into a VXI chassis.
3. The 1260-145 module is shipped in an anti-static bag to prevent electrostatic damage to the module. Do not remove the module from the anti-static bag unless it is in a static-controlled area.
1260-145 User Manual Publication No. 980824-145 Rev. A
Installation Instructions 2-2 Astronics Test Systems
Installation Installation of the 1260-145 Switching Module into a 1260-100 Carrier assembly is described in the Installation section of the 1260-100 Adapt-a-Switch Carrier Manual.
Module Configuration
The 1260-145 module is available in seven different configurations providing a wide variety of matrix sizes. Refer to Chapter 1 for more information about specific configurations.
Front Panel Connectors
The 1260-145 has one 160-pin front-panel connector, labeled J200. It is a 160-pin, DIN “E” style, with 0.040” rectangular posts as pins. See Figure 2-1 for pin numbering. Refer to Chapter 3 for channel to pin mapping. For a block diagram of the 1260-145 see Figure 2-2.
Figure 2-1, Front-Panel Connector Pin Numbering
3231302928272625242322212019181716151413121110987654321
ABCDE
DIN41612Front Panel
Connector Pinout
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Installation Instructions 2-3
Figure 2-2, 1260-145 Block Diagram
Mating Connectors
Mating connector accessories are available:
160-Pin Connector Kit with backshell and pins, P/N 407664
160-Pin Cable Assembly, 6 Ft., 24 AWG, P/N 407408-001
The 160-Pin Connector Kit consists of a connector housing, and 170 crimp pins. After wire attachment, the pin is inserted into the housing and will snap into place, providing positive retention.
The suggested crimp tool for the crimp pins is P/N 990897. The corresponding pin insertion tool is P/N 990898 and the removal tool is P/N 990899.
The 160-Pin Cable Assembly uses 24 AWG cable with crimp pins to mate with the 1260-145. The other cable end is un-terminated. Refer to Chapter 3 for channel-to-pin mapping information.
Logic CoreControlInformation
Serialto
ParallelConverter
InputLatches
8x18
Parallelto
SerialConverter
DPDT RelayModule Driver
OutputLatches
8x18
Control
Readback
ROWA
COLB
Gnd
160 PIN USERINTERFACE
CONNECTOR
48 PIN CARDINTERFACE
CONNECTOR
1260-145BLOCK DIAGRAM
Vcc COLA
Gnd
Readback
Control
4x4, 4x12,4x16, 4x36,8x8, 8x16,
12x12Chans
ROWB
COLB
ROWA
COLA
COLB
1260-145 User Manual Publication No. 980824-145 Rev. A
Installation Instructions 2-4 Astronics Test Systems
This page was left intentionally blank.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-1
Chapter 3 MODULE OPERATION
Setting the Module Address
The Option-01T switch controller identifies each Adapt-a-Switch plug-in or conventional 1260-Series module by a module address that is unique to that module. The module address is a number from 1 through 12, inclusive.
The module address assigned to the 1260-145 depends on the carrier slot into which the 1260-145 is inserted, and on the position of the logical address DIP switch on the carrier side panel. The switch has two settings:
! 1-6 (closed): When the switch is set to this position, the module addresses of the plug-ins in the 1260-100 Carrier are from 1 through 6. The module with address 1 is in the left slot of the top row. The plug-ins are addressed in the following pattern:
Front View – Module Addresses for 1 through 6
1
2
3
4
5
6
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-2 Astronics Test Systems
• 7 - 12 (open): When the switch is set to this position, the module addresses of the plug-ins in the 1260-100 Carrier are from 7 through 12, in the following pattern:
Front View – Module Addresses for 7 through 12
When setting module addresses for Adapt-a-Switch Carriers and conventional 1260-Series modules, be sure that no address is used by more than one plug-in or 1260-Series module.
For instructions on setting module addresses for a conventional 1260-Series module, see the label on the side panel of the module.
Operating Modes The 1260-145 may be operated either in message-based mode or in register-based mode.
In the message-based mode, the 1260-01T switch controller interprets commands sent by the slot 0 controller, and determines the appropriate data to send to the control registers of the 1260-145 module.
If the A24 VXI base address for the 1260-100 Adapt-A-Switch carrier is assumed to be at 0x804000A for example purposes and the 1260-145 occupies the module 0 slot, Figure 3-1 below provides a conceptual view of the message-based mode of operation for a read operation on port 1.
7
8
9
10
11
12
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-3
Figure 3-1, Message-Based Mode of Operation
In the register-based mode, the user writes directly to the port registers on the 1260-145 module. The 1260-01T command module does not monitor these operations, and does not keep track of the port states on the 1260-145 module in this mode.
A conceptual view of the register-based mode is shown in Figure 3-2 below.
Figure 3-2, Register-Based Mode of Operation
Since the 1260-01T switch controller does not keep track of port and control register states during the register-based mode, it is advisable to use either the message-based or the register-based mode consistently, and use the chosen mode exclusively throughout the application program.
In general, the message-based mode of operation is easier to use with utility software such as the National Instruments VXI Interactive Control (VIC) program. The message-based mode allows the user to send ASCII text commands to the 1260-01T and to read replies from the 1260-01T. In addition, some features, such as scan lists, are available only in the message-based mode.
The register-based mode provides faster and more direct control of the 1260-145. In this mode, direct port and control register operations are processed in less than 9 microseconds, not counting software overhead inherent in I/O libraries such as VISA.
For further information about message-based vs. register-based
PC (MXI) 1260-01T 1260-145 VXIbus
"CLOSE (@1(0))" Write to A24 Address {base address + 0x401}
PC (MXI) 1260-145
Write to A24 Address {base address + 0x401}
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-4 Astronics Test Systems
comparisons, consult the 1260-01T User’s Manual for further details.
Operating In Message-Based Mode
Channel Descriptors For The 1260-145
The standard 1260-01T commands are used to operate the 1260-145 module. These commands are described in the 1260-01T User’s Manual.
Each 1260-01T port command uses a channel descriptor to select the channel(s) of interest. The syntax for a channel descriptor is the same for all 1260 series modules. In general, the following syntax is used to select a single channel:
@ <module address> ( <channel> ) )
Where:
• <module address> is the address of the 1260-145 module. This is a number is in the range from 1 through 12, inclusive.
• <channel> is the 1260-145 relay to operate. This number can be obtained for a given card and a given relay by referring to Figure 3-3 and one of the applicable card types illustrated in Figures 3-5 through 3-11. These figures provide a message-based channel descriptor (MBC) for each unique relay on any 1260-145 card.
Multiple individual channels may be specified using the following channel descriptor syntax:
@ <module address> ( <channel1> , <channel2> , . . ., <channelN> ))[,data]
A range of channels may be specified using the following channel descriptor syntax:
@ <module address> ( <first channel> : <last channel> ))
The following examples illustrate the use of the channel descriptors for the 1260-145:
CLOSE (@8(0)) Closes relay 0 at module address 8
OPEN (@3(1000)) Opens relay 1000 at module address 3
The message-based descriptors (MBC) provided in Figures 3-5 through 3-11 serve a secondary purpose. In addition to
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-5
specifying an exact relay (i.e. relay 1000), the syntax of the message-based descriptor indicates which matrix the relay belongs to, and the column and row numbers which intersect the relay position. Figure 3-4 identifies for each 1260-145 variant how to interpret the message-based descriptor to determine these parameters.
Reply To The MOD:LIST? Command
The 1260-01T returns a reply to the MOD:LIST? Command. This reply is unique for each different 1260 series switch module. The syntax for the reply is:
<module address> : <module-specific identification string>
The <module-specific identification string> for the 1260-145 depends on the version. For the standard versions 1260-145A through 1260-145G these are:
1260-145A 9-4X4 MATRIX MODULE
1260-145B 3-4X12 MATRIX MODULE
1260-145C 2-4X16 MATRIX MODULE
1260-145D 4X36 MATRIX MODULE
1260-145E 2-8X8 MATRIX MODULE
1260-145F 8X16 MATRIX MODULE
1260-145G 12X12 MATRIX MODULE
So, for a 1260-145C whose <module address> is set to 8, the reply to this query would be:
8 : 1260-145C 2-4X16 MATRIX MODULE
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-6 Astronics Test Systems
Operating The 1260-145 in Register-Based Mode
In register-based mode, the 1260-145 is operated by directly writing and reading to/from ports controlling eight relays each. To access the various registers the following details must be assembled to generate an absolute address that can be wrote or read from:
The control registers are located in the VXIbus A24 Address Space. The A24 address for a control register depends on:
1. The A24 Address Offset assigned to the 1260-01T module by the Resource Manager program. The Resource Manager program is provided by the VXIbus slot-0 controller vendor. The A24 Address Offset is placed into the “Offset Register” of the 1260-01T by the Resource Manager.
2. The <module address> of the 1260-145 module. This is a value in the range from 1 and 12 inclusive.
3. The 1260-145 control register to be written to or read from. Each register on the 1260-145 has a unique offset from the base address.
The base A24 address for the 1260-145 module may be calculated by:
(A24 Offset of the 1260-01T) + (1024 x Module Address of 1260-145).
The A24 address offset is usually expressed in hexadecimal. A typical value of 20400016 is used in the examples that follow.
A 1260-145 with a module address of 7 would have the base A24 address computed as follows:
Base A24 Address of 1260-145 = 20400016 + (40016 x 710) = 205C0016
The control registers for Adapt-a-Switch plug-ins and conventional 1260-Series modules are always on odd-numbered A24 addresses. This number can be obtained for a given card and a given relay by referring to Figure 3-3 and one of the applicable card types illustrated in Figures 3-5 through 3-11. These figures provide a register-based address offset and bit position (Off-bit) for each unique relay on any 1260-145 card. Once this offset is known, the absolute address where data is to be written or read from is simply assembled by adding the base address to the offset:
(Base A24 1260-145 Address) + offset = absolute address
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-7
If slot 7 is assumed to be occupied by a 1260-145A card for illustration purposes, from our example base A24 address computed earlier, the following absolute addresses would apply for the operations indicated:
205C01 Read or write to register controlling relays 0-3 and 100-103
205C0D Read or write to register controlling relays 3000-3003 and 3100-3103
Writing to a control register location is a straightforward process. Setting a bit high in a control register causes the appropriate relay to close and setting the same bit low causes the relay to open. Because of the hardware architecture used in the 1260-145, a control register written to with a value will be inverted (one’s complement) when read back.
It is especially important to realize that a single write operation to a control register will affect eight relays simultaneously. Therefore if only a single bit change is desired, the following process must be observed.
1. Read the register first, inverting the bit pattern if necessary
2. Mask the appropriate bit with an ‘AND’ operation and a byte mask with all undesired bits set to a ‘1’ and the desired bit set to a ‘0’ or ‘1’ depending on whether the bit is to be set or cleared in the desired register
3. Write the masked data back into the register
As simple as this may seem, a number of products reported as faulty and sent back for repair are nothing more than the result of inappropriate register accesses.
The message-based descriptors (MBC) provided in Figures 3-5 through 3-11 are not directly relative to register-based operation. They do, however, serve a secondary purpose in register-based operation. In addition to specifying an exact relay (i.e. relay 1000), the syntax of the message-based descriptor indicates which matrix the relay belongs to, and the column and row numbers which intersect the relay position. Figure 3-4 identifies for each 1260-145 variant how to interpret the message-based descriptor to determine these parameters.
The VISA I/O library may be used to control the module. The VISA function viOut8() is used to write a single 8-bit byte to a control register, while viIn8() is used to read a single 8-bit byte from the control register. The following code example shows the use of viOut8() to update the 1260-145 module.
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-8 Astronics Test Systems
Figure 3-3, Numbering Nomenclature for all 1260-145 Variants
Physical MatrixNumber = 6
Position = (2,0)
Physical MatrixNumber = 7
Position = (2,1)
Physical MatrixNumber = 8
Position = (2,2)
Physical MatrixNumber = 3
Position = (1,0)
Physical MatrixNumber = 4
Position = (1,1)
Physical MatrixNumber = 5
Position = (1,2)
Physical MatrixNumber = 0
Position = (0,0)
Physical MatrixNumber = 1
Position = (0,1)
Physical MatrixNumber = 2
Position = (0,2)
3231302928272625242322212019181716151413121110987654321
ABCDE
DIN41612Front Panel
Connector Pinout
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
MBC,Off-bit
(B)xx(A)xx
(B)xx(A)xx
(B)xx(A)xx
(B)xx(A)xx
(A)xx(B)xx
(A)xx(B)xx
(A)xx(B)xx
(A)xx(B)xx
n
Physical Matrix Nomenclature
Shie
ld G
roun
d Pi
ns: B
13, B
18, B
19, C
9-C
19, D
17, E
17
= Physical matrix number (n = 0-8)(A)xx = High Connector pin position (xx = A1-E32)(B)xx = Low Connector pin position (xx = A1-E32)MBC = Message-based channel descriptor for relay
(also used as a general relay number)Off-bit = Register-based address offset (0x01-0x23)
and bit location (0-7) for relay
n
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-9
Figure 3-4, Message-Based Channel Descriptor to Physical Switch Orientation
1260-145AMessage Based
DescriptorMRCC {M = Matrix Number (0-8)
R = Row Number (0-3)
CC = Column Number (00-03)
1260-145BMessage Based
DescriptorMRRCC {M = Matrix Number (0-2)
RR = Row Number (00-03)
CC = Column Number (00-11)
1260-145CMessage Based
DescriptorMRRCC {M = Matrix Number (0-1)
RR = Row Number (00-15)
CC = Column Number (00-03)
RRCC1260-145D
Message BasedDescriptor {1260-145E
Message BasedDescriptor
MRRCC {M = Matrix Number (0-1)
RR = Row Number (00-07)
CC = Column Number (00-07)
1260-145FMessage Based
DescriptorRRCC {
1260-145GMessage Based
DescriptorRRCC {RR = Row Number (00-11)
CC = Column Number (00-11)
RR = Row Number (00-15)
CC = Column Number (00-07)
RR = Row Number (00-35)
CC = Column Number (00-03)
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-10 Astronics Test Systems
Figure 3-5, 1260-145A Connector/Channel Organization
6
B28B27
B26B25
B32B31
B30B29
6300,0x1b-4
6200,0x1b-0
6100,0x19-4
6000,0x19-0
6301,0x1b-5
6302,0x1b-6
6303,0x1b-7
6201,0x1b-1
6202,0x1b-2
6203,0x1b-3
6101,0x19-5
6102,0x19-6
6103,0x19-7
6001,0x19-1
6002,0x19-2
6003,0x19-3
E27D27
E28D28
E29D29
E30D30
7300,0x1f-4
7200,0x1f-0
7100,0x1d-4
7000,0x1d-0
7301,0x1f-5
7302,0x1f-6
7303,0x1f-7
7201,0x1f-1
7202,0x1f-2
7203,0x1f-3
7101,0x1d-5
7102,0x1d-6
7103,0x1d-7
7001,0x1d-1
7002,0x1d-2
7003,0x1d-3
A28A27
A26A25
A32A31
A30A29
E31D31
E32D32
E25D25
E26D26
7
8300,0x23-4
8200,0x23-0
8100,0x21-4
8000,0x21-0
8301,0x23-5
8302,0x23-6
8303,0x23-7
8201,0x23-1
8202,0x23-2
8203,0x23-3
8101,0x21-5
8102,0x21-6
8103,0x21-7
8001,0x21-1
8002,0x21-2
8003,0x21-3
B24B23
B22B21
A24A23
A22A21
C25C26
C27C28
C29C30
C31C32
8
5
5300,0x17-4
5200,0x17-0
5100,0x15-4
5000,0x15-0
5301,0x17-5
5302,0x17-6
5303,0x17-7
5201,0x17-1
5202,0x17-2
5203,0x17-3
5101,0x15-5
5102,0x15-6
5103,0x15-7
5001,0x15-1
5002,0x15-2
5003,0x15-3
A9A10
A11A12
C21C22
C23C24
D23E23
D24E24
B12B11
B10B9
4300,0x13-4
4200,0x13-0
4100,0x11-4
4000,0x11-0
4301,0x13-5
4302,0x13-6
4303,0x13-7
4201,0x13-1
4202,0x13-2
4203,0x13-3
4101,0x11-5
4102,0x11-6
4103,0x11-7
4001,0x11-1
4002,0x11-2
4003,0x11-3
D9E9
D10E10
E20D20
C20B20
A17A18
A19A20
D21E21
D22E22
4
3300,0x0f-4
3200,0x0f-0
3100,0x0d-4
3000,0x0d-0
3301,0x0f-5
3302,0x0f-6
3303,0x0f-7
3201,0x0f-1
3202,0x0f-2
3203,0x0f-3
3101,0x0d-5
3102,0x0d-6
3103,0x0d-7
3001,0x0d-1
3002,0x0d-2
3003,0x0d-3
D11E11
D12E12
E18D18
E19D19
B14B15
B16B17
A16A15
A14A13
3
0300,0x03-4
0200,0x03-0
0100,0x01-4
0000,0x01-0
0301,0x03-5
0302,0x03-6
0303,0x03-7
0201,0x03-1
0202,0x03-2
0203,0x03-3
0101,0x01-5
0102,0x01-6
0103,0x01-7
0001,0x01-1
0002,0x01-2
0003,0x01-3
B4B3
B2B1
B8B7
B6B5
E6D6
E5D5
E4D4
E3D3
0
1300,0x07-4
1200,0x07-0
1100,0x05-4
1000,0x05-0
1301,0x07-5
1302,0x07-6
1303,0x07-7
1201,0x07-1
1202,0x07-2
1203,0x07-3
1101,0x05-5
1102,0x05-6
1103,0x05-7
1001,0x05-1
1002,0x05-2
1003,0x05-3
A4A3
A2A1
A8A7
A6A5
E2D2
E1D1
E13D13
E14D14
1 2
2300,0x0b-4
2200,0x0b-0
2100,0x09-4
2000,0x09-0
2301,0x0b-5
2302,0x0b-6
2303,0x0b-7
2201,0x0b-1
2202,0x0b-2
2203,0x0b-3
2101,0x09-5
2102,0x09-6
2103,0x09-7
2001,0x09-1
2002,0x09-2
2003,0x09-3
D7E7
D8E8
E15D15
E16D16
C8C7
C6C5
C4C3
C2C1
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-11
Figure 3-6, 1260-145B Connector/Channel Organization
00300,0x03-4
00200,0x03-0
00100,0x01-4
00000,0x01-0
00301,0x03-5
00302,0x03-6
00303,0x03-7
00201,0x03-1
00202,0x03-2
00203,0x03-3
00101,0x01-5
00102,0x01-6
00103,0x01-7
00001,0x01-1
00002,0x01-2
00003,0x01-3
B4B3
B2B1
B8B7
B6B5
E6D6
E5D5
E4D4
E3D3
0
00304,0x07-4
00204,0x07-0
00104,0x05-4
00004,0x05-0
00305,0x07-5
00306,0x07-6
00307,0x07-7
00205,0x07-1
00206,0x07-2
00207,0x07-3
00105,0x05-5
00106,0x05-6
00107,0x05-7
00005,0x05-1
00006,0x05-2
00007,0x05-3
E2D2
E1D1
E13D13
E14D14
1 2
00308,0x0b-4
00208,0x0b-0
00108,0x09-4
00008,0x09-0
00309,0x0b-5
00310,0x0b-6
00311,0x0b-7
00209,0x0b-1
00210,0x0b-2
00211,0x0b-3
00109,0x09-5
00110,0x09-6
00111,0x09-7
00009,0x09-1
00010,0x09-2
00011,0x09-3
C8C7
C6C5
C4C3
C2C1
5
10308,0x17-4
10208,0x17-0
10108,0x15-4
10008,0x15-0
10309,0x17-5
10310,0x17-6
10311,0x17-7
10209,0x17-1
10210,0x17-2
10211,0x17-3
10109,0x15-5
10110,0x15-6
10111,0x15-7
10009,0x15-1
10010,0x15-2
10011,0x15-3
D23E23
D24E24
B12B11
B10B9
10304,0x13-4
10204,0x13-0
10104,0x11-4
10004,0x11-0
10305,0x13-5
10306,0x13-6
10307,0x13-7
10205,0x13-1
10206,0x13-2
10207,0x13-3
10105,0x11-5
10106,0x11-6
10107,0x11-7
10005,0x11-1
10006,0x11-2
10007,0x11-3
A17A18
A19A20
D21E21
D22E22
4
10300,0x0f-4
10200,0x0f-0
10100,0x0d-4
10000,0x0d-0
10301,0x0f-5
10302,0x0f-6
10303,0x0f-7
10201,0x0f-1
10202,0x0f-2
10203,0x0f-3
10101,0x0d-5
10102,0x0d-6
10103,0x0d-7
10001,0x0d-1
10002,0x0d-2
10003,0x0d-3
D11E11
D12E12
E18D18
E19D19
B14B15
B16B17
A16A15
A14A13
3
6
B28B27
B26B25
B32B31
B30B29
20300,0x1b-4
20200,0x1b-0
20100,0x19-4
20000,0x19-0
20301,0x1b-5
20302,0x1b-6
20303,0x1b-7
20201,0x1b-1
20202,0x1b-2
20203,0x1b-3
20101,0x19-5
20102,0x19-6
20103,0x19-7
20001,0x19-1
20002,0x19-2
20003,0x19-3
E27D27
E28D28
E29D29
E30D30
20304,0x1f-4
20204,0x1f-0
20104,0x1d-4
20004,0x1d-0
20305,0x1f-5
20306,0x1f-6
20307,0x1f-7
20205,0x1f-1
20206,0x1f-2
20207,0x1f-3
20105,0x1d-5
20106,0x1d-6
20107,0x1d-7
20005,0x1d-1
20006,0x1d-2
20007,0x1d-3
E31D31
E32D32
E25D25
E26D26
7
20308,0x23-4
20208,0x23-0
20108,0x21-4
20008,0x21-0
20309,0x23-5
20310,0x23-6
20311,0x23-7
20209,0x23-1
20210,0x23-2
20211,0x23-3
20109,0x21-5
20110,0x21-6
20111,0x21-7
20009,0x21-1
20010,0x21-2
20011,0x21-3
C25C26
C27C28
C29C30
C31C32
8
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-12 Astronics Test Systems
Figure 3-7, 1260-145C Connector/Channel Organization
00300,0x03-4
00200,0x03-0
00100,0x01-4
00000,0x01-0
00301,0x03-5
00302,0x03-6
00303,0x03-7
00201,0x03-1
00202,0x03-2
00203,0x03-3
00101,0x01-5
00102,0x01-6
00103,0x01-7
00001,0x01-1
00002,0x01-2
00003,0x01-3
E6D6
E5D5
E4D4
E3D3
0
00700,0x0f-4
00600,0x0f-0
00500,0x0d-4
00400,0x0d-0
00701,0x0f-5
00702,0x0f-6
00703,0x0f-7
00601,0x0f-1
00602,0x0f-2
00603,0x0f-3
00501,0x0d-5
00502,0x0d-6
00503,0x0d-7
00401,0x0d-1
00402,0x0d-2
00403,0x0d-3 3
6
01100,0x1b-4
01000,0x1b-0
00900,0x19-4
00800,0x19-0
01101,0x1b-5
01102,0x1b-6
01103,0x1b-7
01001,0x1b-1
01002,0x1b-2
01003,0x1b-3
00901,0x19-5
00902,0x19-6
00903,0x19-7
00801,0x19-1
00802,0x19-2
00803,0x19-3
1
01500,0x07-4
01400,0x07-0
01300,0x05-4
01200,0x05-0
01501,0x07-5
01502,0x07-6
01503,0x07-7
01401,0x07-1
01402,0x07-2
01403,0x07-3
01301,0x05-5
01302,0x05-6
01303,0x05-7
01201,0x05-1
01202,0x05-2
01203,0x05-3
B4B3
B2B1
B8B7
B6B5
D11E11
D12E12
E18D18
E19D19
B28B27
B26B25
B32B31
B30B29
A4A3
A2A1
A8A7
A6A5
10700,0x17-4
10600,0x17-0
10500,0x15-4
10400,0x15-0
10701,0x17-5
10702,0x17-6
10703,0x17-7
10601,0x17-1
10602,0x17-2
10603,0x17-3
10501,0x15-5
10502,0x15-6
10503,0x15-7
10401,0x15-1
10402,0x15-2
10403,0x15-3 5
10300,0x0b-4
10200,0x0b-0
10100,0x09-4
10000,0x09-0
10301,0x0b-5
10302,0x0b-6
10303,0x0b-7
10201,0x0b-1
10202,0x0b-2
10203,0x0b-3
10101,0x09-5
10102,0x09-6
10103,0x09-7
10001,0x09-1
10002,0x09-2
10003,0x09-3
C8C7
C6C5
C4C3
C2C1
2
11100,0x23-4
11000,0x23-0
10900,0x21-4
10800,0x21-0
11101,0x23-5
11102,0x23-6
11103,0x23-7
11001,0x23-1
11002,0x23-2
11003,0x23-3
10901,0x21-5
10902,0x21-6
10903,0x21-7
10801,0x21-1
10802,0x21-2
10803,0x21-3 8
11500,0x1f-4
11400,0x1f-0
11300,0x1d-4
11200,0x1d-0
11501,0x1f-5
11502,0x1f-6
11503,0x1f-7
11401,0x1f-1
11402,0x1f-2
11403,0x1f-3
11301,0x1d-5
11302,0x1d-6
11303,0x1d-7
11201,0x1d-1
11202,0x1d-2
11203,0x1d-3 7
D7E7
D8E8
E15D15
E16D16
A9A10
A11A12
C21C22
C23C24
B24B23
B22B21
A24A23
A22A21
A28A27
A26A25
A32A31
A30A29
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-13
Figure 3-8, 1260-145D Connector/Channel Organization
2
D7E7
D8E8
E15D15
E16D16
1100,0x0b-4
1000,0x0b-0
0900,0x09-4
0800,0x09-0
1101,0x0b-5
1102,0x0b-6
1103,0x0b-7
1001,0x0b-1
1002,0x0b-2
1003,0x0b-3
0901,0x09-5
0902,0x09-6
0903,0x09-7
0801,0x09-1
0802,0x09-2
0803,0x09-3
2300,0x17-4
2200,0x17-0
2100,0x15-4
2000,0x15-0
2301,0x17-5
2302,0x17-6
2303,0x17-7
2201,0x17-1
2202,0x17-2
2203,0x17-3
2101,0x15-5
2102,0x15-6
2103,0x15-7
2001,0x15-1
2002,0x15-2
2003,0x15-3
A9A10
A11A12
C21C22
C23C24
5
3500,0x23-4
3400,0x23-0
3300,0x21-4
3200,0x21-0
3501,0x23-5
3502,0x23-6
3503,0x23-7
3401,0x23-1
3402,0x23-2
3403,0x23-3
3301,0x21-5
3302,0x21-6
3303,0x21-7
3201,0x21-1
3202,0x21-2
3203,0x21-3
B24B23
B22B21
A24A23
A22A21
8
7
3100,0x1f-4
3000,0x1f-0
2900,0x1d-4
2800,0x1d-0
3101,0x1f-5
3102,0x1f-6
3103,0x1f-7
3001,0x1f-1
3002,0x1f-2
3003,0x1f-3
2901,0x1d-5
2902,0x1d-6
2903,0x1d-7
2801,0x1d-1
2802,0x1d-2
2803,0x1d-3
A28A27
A26A25
A32A31
A30A29
1900,0x13-4
1800,0x13-0
1700,0x11-4
1600,0x11-0
1901,0x13-5
1902,0x13-6
1903,0x13-7
1801,0x13-1
1802,0x13-2
1803,0x13-3
1701,0x11-5
1702,0x11-6
1703,0x11-7
1601,0x11-1
1602,0x11-2
1603,0x11-3
D9E9
D10E10
E20D20
C20B20
4
0700,0x07-4
0600,0x07-0
0500,0x05-4
0400,0x05-0
0701,0x07-5
0702,0x07-6
0703,0x07-7
0601,0x07-1
0602,0x07-2
0603,0x07-3
0501,0x05-5
0502,0x05-6
0503,0x05-7
0401,0x05-1
0402,0x05-2
0403,0x05-3
A4A3
A2A1
A8A7
A6A5
1
0300,0x03-4
0200,0x03-0
0100,0x01-4
0000,0x01-0
0301,0x03-5
0302,0x03-6
0303,0x03-7
0201,0x03-1
0202,0x03-2
0203,0x03-3
0101,0x01-5
0102,0x01-6
0103,0x01-7
0001,0x01-1
0002,0x01-2
0003,0x01-3
B4B3
B2B1
B8B7
B6B5
E6D6
E5D5
E4D4
E3D3
0
1500,0x0f-4
1400,0x0f-0
1300,0x0d-4
1200,0x0d-0
1501,0x0f-5
1502,0x0f-6
1503,0x0f-7
1401,0x0f-1
1402,0x0f-2
1403,0x0f-3
1301,0x0d-5
1302,0x0d-6
1303,0x0d-7
1201,0x0d-1
1202,0x0d-2
1203,0x0d-3
D11E11
D12E12
E18D18
E19D19
3 6
2700,0x1b-4
2600,0x1b-0
2500,0x19-4
2400,0x19-0
2701,0x1b-5
2702,0x1b-6
2703,0x1b-7
2601,0x1b-1
2602,0x1b-2
2603,0x1b-3
2501,0x19-5
2502,0x19-6
2503,0x19-7
2401,0x19-1
2402,0x19-2
2403,0x19-3
B28B27
B26B25
B32B31
B30B29
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-14 Astronics Test Systems
Figure 3-9, 1260-145E Connector/Channel Organization
00704,0x13-4
00604,0x13-0
00504,0x11-4
00404,0x11-0
00705,0x13-5
00706,0x13-6
00707,0x13-7
00605,0x13-1
00606,0x13-2
00607,0x13-3
00505,0x11-5
00506,0x11-6
00507,0x11-7
00405,0x11-1
00406,0x11-2
00407,0x11-3 4
00700,0x0f-4
00600,0x0f-0
00500,0x0d-4
00400,0x0d-0
00701,0x0f-5
00702,0x0f-6
00703,0x0f-7
00601,0x0f-1
00602,0x0f-2
00603,0x0f-3
00501,0x0d-5
00502,0x0d-6
00503,0x0d-7
00401,0x0d-1
00402,0x0d-2
00403,0x0d-3
D11E11
D12E12
E18D18
E19D19
3
00300,0x03-4
00200,0x03-0
00100,0x01-4
00000,0x01-0
00301,0x03-5
00302,0x03-6
00303,0x03-7
00201,0x03-1
00202,0x03-2
00203,0x03-3
00101,0x01-5
00102,0x01-6
00103,0x01-7
00001,0x01-1
00002,0x01-2
00003,0x01-3
B4B3
B2B1
B8B7
B6B5
E6D6
E5D5
E4D4
E3D3
0
00304,0x07-4
00204,0x07-0
00104,0x05-4
00004,0x05-0
00305,0x07-5
00306,0x07-6
00307,0x07-7
00205,0x07-1
00206,0x07-2
00207,0x07-3
00105,0x05-5
00106,0x05-6
00107,0x05-7
00005,0x05-1
00006,0x05-2
00007,0x05-3
E2D2
E1D1
E13D13
E14D14
1
10704,0x1f-4
10604,0x1f-0
10504,0x1d-4
10404,0x1d-0
10705,0x1f-5
10706,0x1f-6
10707,0x1f-7
10605,0x1f-1
10606,0x1f-2
10607,0x1f-3
10505,0x1d-5
10506,0x1d-6
10507,0x1d-7
10405,0x1d-1
10406,0x1d-2
10407,0x1d-3 7
10700,0x17-4
10600,0x17-0
10500,0x15-4
10400,0x15-0
10701,0x17-5
10702,0x17-6
10703,0x17-7
10601,0x17-1
10602,0x17-2
10603,0x17-3
10501,0x15-5
10502,0x15-6
10503,0x15-7
10401,0x15-1
10402,0x15-2
10403,0x15-3
A9A10
A11A12
C21C22
C23C24
5
10300,0x0b-4
10200,0x0b-0
10100,0x09-4
10000,0x09-0
10301,0x0b-5
10302,0x0b-6
10303,0x0b-7
10201,0x0b-1
10202,0x0b-2
10203,0x0b-3
10101,0x09-5
10102,0x09-6
10103,0x09-7
10001,0x09-1
10002,0x09-2
10003,0x09-3
D7E7
D8E8
E15D15
E16D16
C8C7
C6C5
C4C3
C2C1
2
10304,0x23-4
10204,0x23-0
10104,0x21-4
10004,0x21-0
10305,0x23-5
10306,0x23-6
10307,0x23-7
10205,0x23-1
10206,0x23-2
10207,0x23-3
10105,0x21-5
10106,0x21-6
10107,0x21-7
10005,0x21-1
10006,0x21-2
10007,0x21-3
C25C26
C27C28
C29C30
C31C32
8
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-15
Figure 3-10, 1260-145F Connector/Channel Organization
0704,0x13-4
0604,0x13-0
0504,0x11-4
0404,0x11-0
0705,0x13-5
0706,0x13-6
0707,0x13-7
0605,0x13-1
0606,0x13-2
0607,0x13-3
0505,0x11-5
0506,0x11-6
0507,0x11-7
0405,0x11-1
0406,0x11-2
0407,0x11-3 4
0304,0x07-4
0204,0x07-0
0104,0x05-4
0004,0x05-0
0305,0x07-5
0306,0x07-6
0307,0x07-7
0205,0x07-1
0206,0x07-2
0207,0x07-3
0105,0x05-5
0106,0x05-6
0107,0x05-7
0005,0x05-1
0006,0x05-2
0007,0x05-3
E2D2
E1D1
E13D13
E14D14
1
0300,0x03-4
0200,0x03-0
0100,0x01-4
0000,0x01-0
0301,0x03-5
0302,0x03-6
0303,0x03-7
0201,0x03-1
0202,0x03-2
0203,0x03-3
0101,0x01-5
0102,0x01-6
0103,0x01-7
0001,0x01-1
0002,0x01-2
0003,0x01-3
B4B3
B2B1
B8B7
B6B5
E6D6
E5D5
E4D4
E3D3
0
0700,0x0f-4
0600,0x0f-0
0500,0x0d-4
0400,0x0d-0
0701,0x0f-5
0702,0x0f-6
0703,0x0f-7
0601,0x0f-1
0602,0x0f-2
0603,0x0f-3
0501,0x0d-5
0502,0x0d-6
0503,0x0d-7
0401,0x0d-1
0402,0x0d-2
0403,0x0d-3
D11E11
D12E12
E18D18
E19D19
3
1104,0x1f-4
1004,0x1f-0
0904,0x1d-4
0804,0x1d-0
1105,0x1f-5
1106,0x1f-6
1107,0x1f-7
1005,0x1f-1
1006,0x1f-2
1007,0x1f-3
0905,0x1d-5
0906,0x1d-6
0907,0x1d-7
0805,0x1d-1
0806,0x1d-2
0807,0x1d-3 76
B28B27
B26B25
B32B31
B30B29
1100,0x1b-4
1000,0x1b-0
0900,0x19-4
0800,0x19-0
1101,0x1b-5
1102,0x1b-6
1103,0x1b-7
1001,0x1b-1
1002,0x1b-2
1003,0x1b-3
0901,0x19-5
0902,0x19-6
0903,0x19-7
0801,0x19-1
0802,0x19-2
0803,0x19-3
1504,0x23-4
1404,0x23-0
1304,0x21-4
1204,0x21-0
1505,0x23-5
1506,0x23-6
1507,0x23-7
1405,0x23-1
1406,0x23-2
1407,0x23-3
1305,0x21-5
1306,0x21-6
1307,0x21-7
1205,0x21-1
1206,0x21-2
1207,0x21-3 82
D7E7
D8E8
E15D15
E16D16
1500,0x0b-4
1400,0x0b-0
1300,0x09-4
1200,0x09-0
1501,0x0b-5
1502,0x0b-6
1503,0x0b-7
1401,0x0b-1
1402,0x0b-2
1403,0x0b-3
1301,0x09-5
1302,0x09-6
1303,0x09-7
1201,0x09-1
1202,0x09-2
1203,0x09-3
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-16 Astronics Test Systems
Figure 3-11, 1260-145G Connector/Channel Organization
6
B28B27
B26B25
B32B31
B30B29
1100,0x1b-4
1000,0x1b-0
0900,0x19-4
0800,0x19-0
1101,0x1b-5
1102,0x1b-6
1103,0x1b-7
1001,0x1b-1
1002,0x1b-2
1003,0x1b-3
0901,0x19-5
0902,0x19-6
0903,0x19-7
0801,0x19-1
0802,0x19-2
0803,0x19-3
1104,0x1f-4
1004,0x1f-0
0904,0x1d-4
0804,0x1d-0
1105,0x1f-5
1106,0x1f-6
1107,0x1f-7
1005,0x1f-1
1006,0x1f-2
1007,0x1f-3
0905,0x1d-5
0906,0x1d-6
0907,0x1d-7
0805,0x1d-1
0806,0x1d-2
0807,0x1d-3 7
1108,0x23-4
1008,0x23-0
0908,0x21-4
0808,0x21-0
1109,0x23-5
1110,0x23-6
1111,0x23-7
1009,0x23-1
1010,0x23-2
1011,0x23-3
0909,0x21-5
0910,0x21-6
0911,0x21-7
0809,0x21-1
0810,0x21-2
0811,0x21-3 8
5
0708,0x17-4
0608,0x17-0
0508,0x15-4
0408,0x15-0
0709,0x17-5
0710,0x17-6
0711,0x17-7
0609,0x17-1
0610,0x17-2
0611,0x17-3
0509,0x15-5
0510,0x15-6
0511,0x15-7
0409,0x15-1
0410,0x15-2
0411,0x15-3
0704,0x13-4
0604,0x13-0
05040x11-4
0404,0x11-0
0705,0x13-5
0706,0x13-6
0707,0x13-7
0605,0x13-1
0606,0x13-2
0607,0x13-3
0505,0x11-5
0506,0x11-6
0507,0x11-7
0405,0x11-1
0406,0x11-2
0407,0x11-3 4
0700,0x0f-4
0600,0x0f-0
0500,0x0d-4
0400,0x0d-0
0701,0x0f-5
0702,0x0f-6
0703,0x0f-7
0601,0x0f-1
0602,0x0f-2
0603,0x0f-3
0501,0x0d-5
0502,0x0d-6
0503,0x0d-7
0401,0x0d-1
0402,0x0d-2
0403,0x0d-3
D11E11
D12E12
E18D18
E19D19
3
0300,0x03-4
0200,0x03-0
0100,0x01-4
0000,0x01-0
0301,0x03-5
0302,0x03-6
0303,0x03-7
0201,0x03-1
0202,0x03-2
0203,0x03-3
0101,0x01-5
0102,0x01-6
0103,0x01-7
0001,0x01-1
0002,0x01-2
0003,0x01-3
B4B3
B2B1
B8B7
B6B5
E6D6
E5D5
E4D4
E3D3
0
0304,0x07-4
0204,0x07-0
0104,0x05-4
0004,0x05-0
0305,0x07-5
0306,0x07-6
0307,0x07-7
0205,0x07-1
0206,0x07-2
0207,0x07-3
0105,0x05-5
0106,0x05-6
0107,0x05-7
0005,0x05-1
0006,0x05-2
0007,0x05-3
E2D2
E1D1
E13D13
E14D14
1 2
0308,0x0b-4
0208,0x0b-0
0108,0x09-4
0008,0x09-0
0309,0x0b-5
0310,0x0b-6
0311,0x0b-7
0209,0x0b-1
0210,0x0b-2
0211,0x0b-3
0109,0x09-5
0110,0x09-6
0111,0x09-7
0009,0x09-1
0010,0x09-2
0011,0x09-3
C8C7
C6C5
C4C3
C2C1
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Module Operation 3-17
1260-145 Example Code
#include <visa.h> /* This example shows a 1260-01T at logical address 16 and a VXI/MXI */ /* interface */ #define RI1260_01_DESC "VXI::16" /* For a GPIB-VXI interface, and a logical address of 77 */ /* the descriptor would be: "GPIB-VXI::77" */ /* this example shows a 1260-145 with module address 7, control register 1, and write data of 0xAA */ #define MOD_ADDR_145 7 #define CONTROL_REGISTER 1 #define DATA_ITEM 0xAA void example_operate_1260_145(void) { ViUInt8 creg_val; ViBusAddress chan1_addr, offset; ViSession hdl1260; /* VISA handle to the 1260-01T */ ViSession hdlRM; /* VISA handle to the resource manager */ ViStatus error; /* VISA error code */ /* open the resource manager */ /* this must be done once in application program */ error = viOpenDefaultRM (&hdlRM); if (error < 0) { /* error handling code goes here */ } /* get a handle for the 1260-01T */ error = viOpen (hdlRM, RI1260_01_DESC, VI_NULL,VI_NULL, &hdl1260); if (error < 0) { /* error handling code goes here */ } /* form the offset for control register 0 */ /* note that the base A24 Address for the 1260-01T */ /* is already accounted for by VISA calls viIn8() and */
1260-145 User Manual Publication No. 980824-145 Rev. A
Module Operation 3-18 Astronics Test Systems
/* viOut8() */
/* module address shifted 10 places = module address x 1024 */ chan1_addr = (MOD_ADDR_145 << 10) + 1;
offset = chan1_addr + (PORT_NUMBER << 1);
error = viOut8 (vi, VI_A24_SPACE, offset, DATA_ITEM);
if (error < 0)
return( error );
/* close the VISA session */ error = viClose( hdl1260 ); if (error < 0) { /* error handling code goes here */ } }
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Optional Assemblies 4-1
Chapter 4 OPTIONAL ASSEMBLIES
407664 Connector Kit, 160 Pin Crimp ............................................................... 4-3
407408-001 Cable Assy, 160 Pin, 6 ft, 24AWG........................................................ 4-4
1260-145 User Manual Publication No. 980824-145 Rev. A
Optional Assemblies 4-2 Astronics Test Systems
This page was left intentionally blank.
Publication No. 980824-145 Rev. A 1260-145 User Manual
Astronics Test Systems Optional Assemblies 4-3
Assembly 407664 Connector kit, 160 Pin, Crimp Rev Date 7/30/98 Revision A
# Component Description U/M Qty Reqd. REF 1 602258-116 CON-CAB-RCP160C,100S -E EA 1.000 2 602258-900 TRMCRP-SNP-U-F26-20G -E EA 170.000
1260-145 User Manual Publication No. 980824-145 Rev. A
Optional Assemblies 4-4 Astronics Test Systems
NO
TES:
CD
DWG. NO. REV.SH.1407408-001 A
(CAB
LE N
OT
SHO
WN
)
SEE
WIR
E LI
ST F
OR
CO
NTA
CT
ASSI
GN
MEN
TS A
ND
CO
NN
ECTI
ON
S.
TER
MIN
ATE
CAB
LE IN
SULA
TIO
N A
S SH
OW
N, U
SIN
GSH
RIN
K TU
BIN
G (I
TEM
10)
.2 3 4
IDEN
TIFY
CAB
LES
AS S
HO
WN
USI
NG
IND
ELIB
LE B
LAC
KIN
K O
N Y
ELLO
W S
HR
INK
TUBI
NG
(ITE
M 1
1). C
OVE
R W
ITH
CLE
ARSH
RIN
K TU
BIN
G (I
TEM
1) F
OR
IDEN
TIFI
CAT
ION
PR
OTE
CTI
ON
.
2
CAB
LES
ARE
TO B
E BU
ILT
IN P
AIR
S FO
R E
ASE
OF
TEST
ING
. TES
T C
ABLE
ASS
Y U
SIN
G T
EST
PRO
CED
UR
E95
1016
. AFT
ER A
SSY
PASS
ES T
EST,
CU
T TH
E C
ABLE
IN H
ALF,
MAK
ING
TW
O S
EPAR
ATE
CAB
LE A
SSEM
BLIE
S.
1.
(CAB
LE N
OT
SHO
WN
)
PIN
A1
PIN
E32
4 5
210
160
PLC
SR
EV.
CAB
LE 2
1.0"
±.2
5"
.75"
±.2
5"
PIN
A1
PIN
E32
4
1
6 4074
08-0
01
REV
.
REV
.40
7408
-001
REV
.40
7408
-001
CAB
LE 1
CAB
LE 2
3
72.0
±2.0
3
7 8 9
2 PL
CS
A/R
4 PL
CS
POSI
TIO
N L
OC
KIN
G H
EAD
AS C
LOSE
TO
STR
AIN
REL
IEF
BRAC
KET
AS P
OSS
IBLE
2 PL
CS
2 PL
CS
4074
08-0
01
CAB
LE 1
BAG
CAB
LE A
SSEM
BLY
AND
IDEN
TIFY
WIT
H R
ACAL
PAR
TN
UM
BER
"407
408-
001"
AN
D C
UR
REN
T R
EVIS
ION
LET
TER
.5.
2 PL
CS
A/R
11
VIEW
A-A
VIEW
B-B
AA
BB
72.0
±2.0