rada 222-t3 thermostatic mixing valve
TRANSCRIPT
Specify as: Rada 222-t3 dk (1.0.407.07.3)¾” thermostatic mixing valve incorporating Radatherm service-free cartridge, check valves and strainers. Supplied with ¾” flat faced union connectors terminating in 22 mm compression connections.
Dimensions (mm) Flow Diagram
Features the unique “Radatherm” service-free cartridge
Unbeatable temperature control
Complete with check valves and strainers
bathing
Kohler Mira LimitedCromwell RoadCheltenhamgloucestershiregL52 5EP
Specification Enquiriestel: 01242 282527Fax: 01242 282404Email: [email protected]
Rada 222-t3 thERmostatiC mixing vaLvE
108
29 37
65
179
65
86
0.50
10
1.0Pressure Loss – bar
1.5 2.00
20
30
40
50
Flow
Rat
e - I
/min
Installation and MaintenancePlease refer to the appropriate Product manual.
ConnectionsInlet and Outlets: ¾” flat-faced male union. Note! 2 elbows and 1 straight union connectors are supplied, terminating in 22 mm compression connections.
standard connections are hot (left), cold (right).
Approvalsbuildcert tmv3 thermostatic mixing valve scheme approved:LP-T44 - Low Pressure Bathfill up to 44°CLP-T46 - Low Pressure Bathfill up to 46°C (assisted)HP-T44 - High Pressure Bathfill up to 44°CHP-T46 - High Pressure Bathfill up to 46°C (assisted)Certificate No: ETC/15/0597.Complies with the technical requirements of BS7942 for the same designations.designed to comply with European standards En1111 and En1287.WRas approved (Water Regulations advisory scheme).designed, manufactured and supported in accordance with accredited BS EN ISO 9001:2000 Quality Management Systems and bs En iso 14001:2004 Environmental management systems
OperationThe Rada 222-t3 dk is designed to be concealed in a duct/cupboard and must be used with a separate outlet flow control such as a tap.
Materialsbody: dZR brass nickel plated.Locking shroud: White engineering plastic.
Temperature RangeFactory pre-set maximum outlet temperature: 43°C.Minimum temperature differential, blend to either supply: 12°C.Optimum thermostatic control range: 30 °C - 50 °C.Minimum cold water temperature: 1°C.Maximum hot water temperature: 85 °C.Note! the mixing valve can accept temporary temperature excursions above 85°C without damage, however, operation of the mixing valve at such elevated temperatures is not recommended. For reasons of general safety, hot water storage supply temperatures should ideally be maintained at between 60°C - 65°C where serving ablutionary applications.
Pressures/Flow Ratesminimum dynamic supply pressure: 0.15 bar.Minimum flow rate:3 l/min at mid blend.Maximum flow rate: 40 l/min at mid blend (which equates to a maximum pressure loss of 1.2 bar).maximum pressure loss ratio*: 10:1 (in favour of either supply).maximum dynamic supply pressure: 5 bar.maximum static pressure: 10 bar.Note! both hot and cold pressure should be nominally equal.* Pressure loss ratio is determined by subtracting the resistance to flow of the outlet pipework and outlet fittings (generally known as ‘back pressure’, and measured at the outlet of the mixing valve) from the dynamic pressures of the hot and cold water at the inlets of the mixing valve. This is at its extreme when the mixing valve is being used at its lowest flow rate and when the maximum inequality occurs in the pressure of the hot and cold water supplies.
tEChniCaL sPECiFiCation
bathing
Weight
Product gross Weight (Kgs) total PackagedWeight (Kgs)
Rada 222-t3 dk 1.900 2.044
P3142/4
Kohler Mira LimitedCromwell Road, Cheltenhamgloucestershire, gL52 5EP
Specification Enquiriestel: 01242 282527, Fax: 01242 282404Email: [email protected]
Rada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler mira Limited. all rights reserved.no part of this document, or any accompanying document, may be reproduced or transmitted in any form or by any means, including photocopying or electronically, without the permission of Kohler mira Limited.
Specify as: Meynell Bonus (PEBS0026.1P)Bath/thermostatic shower mixer with conventional washer bath tap headworks.
Specify as: Meynell Bonus-ev (PEBS0010.1P)Bath/thermostatic shower mixer with conventional washer bath tap headworks. Supplied complete with shower fittings including multi-mode handset, slide rail, hose and hose retaining ring.
Dimensions (mm) Flow Diagram
Combined manual bath mixer and thermostatic shower
Suitable for all baths with standard 180 mm tap hole centres
Simple and quick to install
Attractive, easy clean design
Standard washer bath tap headworks
Bathing & Showering
Kohler Mira LimitedCromwell roadCheltenhamgloucestershiregL52 5eP
Specification Enquiriestel: 01242 282527Fax: 01242 282404email: [email protected]
meyneLL BonuS Bath and thermoStatiC Shower mixer
180
50 min.
32
122
Hot Cold
nim/l – etaR
wolF
Inlet Pressure – bar
Bath Fill Shower
120
100
80
60
40
20
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.90
Installation and MaintenancePlease refer to the appropriate Product manual.
Connectionsinlets: ¾” BSP male.Shower outlet: ½” BSP male.
ApprovalsDesigned, manufactured and supported in accordance with accredited BS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.
OperationThe outside knobs control the flow of water to the central bathfill outlet. Anticlockwise movement turns the water flow on.
when the central knob is turned on, anticlockwise, water is delivered to the shower outlet.
MaterialsBody: Chrome plated brass.
Temperature RangeFactory preset outlet temperature: 42°C (adjustable).minimum temperature differential between each inlet and preset shower outlet temperature: 10°C.Optimum temperature range: 35°C - 45°C.maximum hot water temperature: 85°C (for safety reasons it is recommended that the hot water storage temperature is maintained at between 60°C to 65°C in ablutionary applications.maximum cold supply temperature: 25°C.maximum hot supply temperature: 85°C.
Pressures/Flow RateMinimum maintained pressure (gravity system): 0.1 bar (to highest shower position).Minimum maintained pressure (gas water heater): 1.0 bar.maximum static pressure: 10 bar.maximum pressure loss ratio: 5:1 (in favour of either supply).Note! Both hot and cold pressure should be nominally equal.
teChniCaL SPeCiFiCation
Bathing & Showering
P3418/5
Kohler Mira LimitedCromwell road, Cheltenhamgloucestershire, gL52 5eP
Specification Enquiriestel: 01242 282527, Fax: 01242 282404email: [email protected]
Rada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may be reproduced or transmitted in any form or by any means, including photocopying or electronically, without the permission of Kohler Mira Limited.
Weight
Product Gross Weight (Kgs) Total PackagedWeight (Kgs)
meynell Bonus 4.860 5.243
Meynell Bonus - ev 6.000 6.868
Bathing & showering
Bathing - applications
Rada Autotherm-3 BSM - TMV2 & TMV3 Approved
autotherm-3 thermostatic bath shower mixer.
Meynell CD
Bath and Thermostatic Shower Mixer
Non-thermostatic bathfill featuring ceramic disc quarter-turn hot and cold taps. Independent, integral thermostatcally controlled, lever operated shower with combined sequential temperature selection and ‘on/off’ control.
rada autotherm-3 BsM
rada autotherm-3 eV Shower Fittings
Kohler Mira LimitedCromwell RoadCheltenhamGloucestershiregl52 5ep
Specification EnquiriesTel: 01242 282527Fax: 01242 282404Email: [email protected]
Bathing & showering
Bathing - applications
Under Bath Thermostatic Mixing Valve - TMV3 Approved
Pre-set thermostatically controlled blended water via adjacent or under bath mixing valve.
P3888/2
Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EP
Specification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: [email protected]
Rada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may be reproduced or transmitted in any form or by any means, including photocopying or electronically, without the permission of Kohler Mira Limited.
Pillar Tap
Rada 222-t3 dk
Specify as follows:Rada SP TD180 1.1503.732 Deck Mounted Bath Spout - Low.A deck mounted bath spout with 180mm throw supplied complete with a flow straightener.
Rada SP THD200 1.1503.733 Deck Mounted Bath Spout.A deck mounted bath spout with 200mm throw supplied complete with a flow straightener.
Rada SP T150 1.1503.734 Wall Mounted Bath Spout - Short.A wall mounted bath spout with 150mm throw supplied complete with a flow straightener.
Rada SP T225 1.1503.735 Wall Mounted Bath Spout - Long.A wall mounted bath spout with 225mm throw supplied complete with a flow straightener.
Rada SP Bidet 1.1503.736 Bidet Spout.A deck mounted bidet spout for ‘over the rim’ delivery supplied with 5 l/min flow regulator.
Range of 3/4” wall and deck mounted bath spouts and 1/2” deck mounted bidet spout for the washroom
Durable polished chrome finish
Easy to install
Bidet spout fitted with 5 litres/minute flow regulator
ß
ß
ß
ß
BAthing
Kohler Mira LimitedCromwell RoadCheltenhamgloucestershiregL52 5EP
Specification Enquiries
tel: 01242 282527Fax: 01242 282404Email: [email protected]
RADA BAth & BiDEt SPOUtS
Deck Mounted Bath Spout
Wall Mounted Bath Spout - Long
Wall Mounted Bath Spout - Short
Bidet Spout
Deck Mounted Bath Spout - Low
Installation and Maintenance
Please refer to the appropriate Product Manual.
AccessoriesAdaptors are available for:¾” BSP to nPt adaptor, Part no: 2.1503.738 wall mounted spouts only.
MaterialsChrome plated brass.
tEChniCAL SPECiFiCAtiOn
BAthing
P4645/1
Kohler Mira LimitedCromwell Road, Cheltenhamgloucestershire, gL52 5EP
Specification Enquiriestel: 01242 282527, Fax: 01242 282404Email: [email protected]
Rada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.no part of this document, or any accompanying document, may be reproduced or transmitted in any form or by any means, including photocopying or electronically, without the permission of Kohler Mira Limited.
Dimensions (mm)
3/4" BSP
225
45
Ø60
SP T225, Part No. 1503.735
180
Ø65.8
3/4" BSP
80
SP TD180, Part No. 1503.732Rada SP tD180, Part no. 1.1503.732 SP THD200, Part No. 1503.733
3/4" BSP
182
122
Ø60
Rada SP thD200, Part no. 1.1503.733 SP T150, Part No. 1503.734
3/4" BSP
150
45
Ø60
Rada SP t150, Part no. 1.1503.734
Rada SP t225, Part no. 1.1503.735 SP Bidet, Part No. 1503.736
107
Ø47
1/2" BSP
Rada SP Bidet, Part no. 1.1503.736
Specify as: Rada Autotherm-3 BSM (1.1533.110)Fully thermostatic bath and shower mixer, TMV 3 approved for both low and high pressure installation and featuring a patented automatic safe temperature adjustment on the shower.Supplied complete with service-free temperature and flow cartridges, check valves, strainers, isolating ball valves and flexible tails.
Specify as: Rada Autotherm-3 EV Shower Fittings (1.1533.117)Shower fittings including 3 mode adjustable chrome handset, slide bar, 1.5 m hose and soap dish.
Specify as: Rada Autotherm-3 EV - CAT 5 Shower Fittings (1.1533.118)Shower fittings including 3 mode adjustable chrome handset, slide bar, 1.5 m hose, soap dish and patented security ring approved for category 5 installations.
Specify as: Rada BSM Shower Fittings (1.1533.247)Shower fittings including 3 mode adjustable chrome handset, slide bar, 1.5 m hose and soap dish.
Dimensions (mm)
The only thermostatic bath and shower mixer approved to the toughest TMV3 healthcare standard
Approved for both high and low pressure use
Also approved to the TMV2 standard for residential use
The only bath shower mixer with the facility to deliver one maximum temperature for bathfill and another for showering
It will automatically reset a safe maximum showering temperature, where a higher bathfill temperature had already been set
Easy “above-the-bath maintenance”, body removable from manifold for easy access to check valves and filters
Supplied complete with service-free temperature and flow cartridges, check valves and flexible tails
Optional shower fittings available, including a category 5 compliant option
bAThIng & ShowErIng
Kohler Mira LimitedCromwell roadCheltenhamgloucestershiregL52 5EP
Specification EnquiriesTel: 01242 282527Fax: 01242 282404Email: [email protected]
rAdA AuToThErM-3 bSM
180
243
145
165
30
64
113152
G½”Shower
G¾” Inlets
40
Installation and MaintenancePlease refer to the appropriate Product Manual.
ConnectionsInlets to bSM body: ¾” bSP male at 180 mm centres.hot left, cold right.Inlets supplied with 0.5 m long flexible hoses: 22 mm compression fitting with isolating valves.Shower outlet: ½” bSP male.
Approvalsbuildcert TMV3 Thermostatic Mixing Valve Scheme approved:LP-S - Low Pressure ShowerLP-T44 - Low Pressure BathfillLP-d44 - diverts to bath and shower with appropriate temperature selectionhP-S - high Pressure ShowerHP-T44 - High Pressure BathfillhP-d44 - diverts to bath and shower with appropriate temperature selectionCertificate No: BC 103 0804.Complies with the technical requirements of bS7942 for the same designations.buildcert TMV2 Thermostatic Mixing Valve Scheme approved:hP-b - high Pressure bidethP-S - high Pressure ShowerhP-w - high Pressure washbasinHP-T - High Pressure BathfillLP-S - Low Pressure ShowerCertificate No: BC 121 0205.designed to comply with European Standards En1111 and En1287.wrAS approved (water regulations Advisory Scheme).designed, manufactured and supported in accordance with accredited bS En ISo 9001:2000 Quality Management Systems and bS En ISo 14001:2004 Environmental Management Systems.
OperationA lever is used to divert between showering and bathfill modes. A separate temperature knob allows alternative temperature selection.
Materialsbody: dZr brass chrome plated.Lever and temperature knob: chrome plated zinc alloy.
Temperature RangeFactory preset to 41°C for shower and 44°C for bathfill.optimum thermostatic control range: 35°C - 45°C.recommended hot: 55°C - 65°C.recommended cold: 5°C - 20°C.
Pressures/Flow RateMaximum static pressure: 10 bar.Maintained inlet pressure range: 0.2 - 5.0 bar.Maximum pressure loss ratio: 10:1 in favour of either supply during flow.Note! both hot and cold pressure should be nominally equal.
TEChnICAL SPECIFICATIon
bAThIng & ShowErIng
Flow Diagram (Low Pressure)
Pressure (Bar)
Low Pressure Bath
.nim/L
wolF
0
10
40
30
20
0.30.2 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Low Pressure Shower
Low Pressure Shower with Handset
High Pressure Bath
High Pressure Shower
High Pressure Shower with Handset
Pressure (Bar)
.nim/L
wolF
0
10
60
30
40
50
20
1.51.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Weight
Product gross weight (Kgs) Total Packagedweight (Kgs)
rada Autotherm-3 bSM
4.530 5.600
EV Shower Fittings 1.170 1.850
EV-CAT5 Shower Fittings
1.170 1.850
P4693/1
Kohler Mira LimitedCromwell road, Cheltenhamgloucestershire, gL52 5EP
Specification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: [email protected]
Rada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.no part of this document, or any accompanying document, may be reproduced or transmitted in any form or by any means, including photocopying or electronically, without the permission of Kohler Mira Limited.
Flow Diagram (High Pressure)
Pressure (Bar)
Low Pressure Bath
.nim/L
wolF
0
10
40
30
20
0.30.2 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Low Pressure Shower
Low Pressure Shower with Handset
High Pressure Bath
High Pressure Shower
High Pressure Shower with Handset
Pressure (Bar)
.nim/L
wolF
0
10
60
30
40
50
20
1.51.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Note! A flow regulator is fitted to the shower outlet. The regulator should be removed if the inlet pressure is below 1 bar.
Specify as: Meynell CD (PEBS0025.1P)Bath/thermostatic shower mixer with quarter turn, ceramic disc bath tap headworks.
Specify as: Meynell CD-ev (PEBS0001.1P)Bath/thermostatic shower mixer with quarter turn, ceramic disc bath tap headworks. Supplied complete with shower fittings including multi-mode handset, slide rail, hose and hose retaining ring.
Dimensions (mm) Flow Diagram
Combined manual bath mixer and thermostatic shower
Suitable for all baths with standard 180 mm tap hole centres
Simple and quick to install
Attractive, easy clean design
Ceramic disc bath tap headworks
Bathing & Showering
Kohler Mira LimitedCromwell roadCheltenhamgloucestershiregL52 5eP
Specification Enquiriestel: 01242 282527Fax: 01242 282404email: [email protected]
meyneLL CD Bath anD thermoStatiC Shower mixer
180
50 min.
32
122
Hot Cold
nim/l – etaR
wolF
Inlet Pressure – bar
Bath Fill Shower
120
100
80
60
40
20
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.90
Installation and MaintenancePlease refer to the appropriate Product manual.
Connectionsinlets: ¾” BSP male.Shower outlet: ½” BSP male.
ApprovalsDesigned, manufactured and supported in accordance with accredited BS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.
OperationThe outside knobs control the flow of water to the central bathfill outlet. Anticlockwise movement turns the water flow on.
when the central knob is turned on, anticlockwise, water is delivered to the shower outlet.
MaterialsBody: Chrome plated brass.
Temperature RangeFactory preset outlet temperature: 42°C (adjustable).minimum temperature differential between each inlet and preset shower outlet temperature: 10°C.Optimum temperature range: 35°C - 45°C.maximum hot water temperature: 85°C (for safety reasons it is recommended that the hot water storage temperature is maintained at between 60°C to 65°C in ablutionary applications.maximum cold supply temperature: 25°C.maximum hot supply temperature: 85°C.
Pressures/Flow RateMinimum maintained pressure (gravity system): 0.1 bar (to highest shower position).Minimum maintained pressure (gas water heater): 1.0 bar.maximum static pressure: 10 bar.maximum pressure loss ratio: 5:1 (in favour of either supply).Note! Both hot and cold pressure should be nominally equal.
teChniCaL SPeCiFiCation
Bathing & Showering
P5480
Kohler Mira LimitedCromwell road, Cheltenhamgloucestershire, gL52 5eP
Specification Enquiriestel: 01242 282527, Fax: 01242 282404email: [email protected]
Rada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may be reproduced or transmitted in any form or by any means, including photocopying or electronically, without the permission of Kohler Mira Limited.
Weight
Product Gross Weight (Kgs) Total PackagedWeight (Kgs)
meynell CD 4.800 5.183
Meynell CD - ev 6.000 6.868