range hoods - amazon s3 jenn-air whirlpool technical education prepared by: whirlpool consumer care...

KitchenAidJenn-Air

Whirlpool

Technical Education

Prepared by: WHIRLPOOL CONSUMER CARE

KR39

Job Aid W10403806

Range HoodsRemoving Control Switches• Removing Blower Motor• Wiring Diagrams•

WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on our products by anyone other than authorized In-Home Service Professionals.

®Registered trademark of Whirlpool, U.S.A., KitchenAid, U.S.A., Jenn-Air, U.S.A., or Maytag Corporation or its related companies. ®MAGIC CHEF is a registered trademark of CNA International, used under license.

© 2011 All rights reserved.

FORWARDThis Range Hood Controls and Motor Access Guide (W10403806), provides the In-Home Service Profes-sional with information on how to access the control switch(es) and exhaust motor on range hoods. For specific information on the model being serviced, refer to the information supplied with the range hood. Always use the Tech Sheet supplied with the product when servicing the range hood.

GOALS AND OBJECTIVESThe goal of this Job Aid is to provide information that will enable the In-Home Service Professional to properly gain access to the control switch(es) and exhaust motor of range hoods.

The objectives of this Job Aid are to:

• Understand and follow proper safety precautions.• Successfully access control or motor components that require repair or replacement.• Successfully return the range hood to its proper operational status.

i

i

GOALS AND OBJECTIVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iSAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

RANGE HOODS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1GXW7330DX, GXW7336DX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

GXW7330DX, GXW7336DX WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 JXI5030WS, JXI5036WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 JXI5030WS, JXI5036WS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 JXW9030WS, JXW9048WS, JXW9036WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

JXW9030WS, JXW9048WS, JXW9036WS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7KXI2536YSS, KXW2530YSS, KXW2548YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8KXI2536YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10KXU4236YSS, KXU4230YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11KXU4236YSS, KXU4230YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13KXU8030YSS, KXU8036YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14KXU8030YSS, KXU8036YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16KXW2336YSS, KXW2330YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17KXW2336YSS, KXW2330YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS . . . . . . . . . . . . 20KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS WIRING DIAGRAM . 22KXW8730YSS, KXW8736YSS, KXW8748YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23KXW8730YSS, KXW8736YSS, KXW8748YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24KXI9736YSS, KXI9748YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25KXI9736YSS, KXI9748YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

IN-LINE, INTERNAL AND EXTERNAL BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

INTERNAL BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 UXB0600D, UXB1200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29IN-LINE BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

UXI0600D, UXI1200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

CONTENTSPage

ADDITIONAL RANGE HOOD WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 JXI8042W, JXI8036W, JXI8242W, JXI8236W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 JXW5030WS, JXW5036WS Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 JXW6030W, JXW6036W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 JXW8030W, JXW8036W, JXW8042W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 JXW8230W, JXW8236W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 JXW8836W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 JXW9030WS, JXW9036WS, JXW9048WS Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 KXI9736Y, KXI9748Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 KXU2830Y KitchenAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 KXI2536Y, KXI2536Y KitchenAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 UXL6048YSS,UXL6036YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 UXG7360VD, UVG73660VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

EXTERNAL BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 KPEU722M, KPEC922M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 KPEU722M, KPEC922M WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

ii

ii

SAFETY FIRST

NOTICE TO THE TECHNICIANIt is the responsibility of the Service Technician to comply with all EPA Regulations and Standards and posses all necessary State and Federal licenses when servicing refrigerators . Federal regulations and Standards can be found on the United States Government EPA Web Site. State Regulations and Standards and

licensing requirements, in most cases, can be found on the State Government Web Site .

iii

1

Electrical Shock HazardDisconnect power before servicing.Replace all parts and panels before operating.Failure to do so can result in death or electrical shock.

Hood is shown from underside removed from Installation

1. Disconnect power to the range hood. 2. Remove the filters. 3. Remove (2) T10 Torx screws screws screws from the under side of the frame at the right corner of the hood, see figure 1. 4. Pull the metal control housing out through the filter opening, see figure 2.

5. Remove (2) T10 Torx screws, one (shown in figure 3) and one on the other side of the box.

To remove the control:

Figure 1

Figure 3

Figure 4 Figure 5

Figure 6

Figure 2


Figure 1

Remove These Screws

Filters

Control

Remove (2) T10 Torx screws, one (shown in figure 3) and one on the other side of the box.

Remove (2) screws

6. Pull the top of the box open slowly. The top of the box is attached by “sheet metal hinges” that will break easily, see figure 4.

7. Remove (3) T10 Torx screws from the bottom of the box to release the plastic switch box, see figure 5.

Remove (3) screwsBend top at this fold (hinges)

bottom of the box to release the plastic

Remove (3) screwsRemove (3) screwsRemove (3) screwsRemove (3) screwsRemove (3) screwsRemove (3) screws

Bend top at this fold (hinges)

bottom of the box to release the plastic switch box, see figure 5.

Bend top at this fold (hinges)Bend top at this fold (hinges)

8. Remove cover to access wire connections, see figure 6.

WhirlpoolGXW7330DXS, GXW7336DX

2 Filters

2

GXW7330DXS, GXW7336DX (continued)Wiring Diagram

12

WIRING DIAGRAM

Motor Resistance (Ohms)

Blue - Red

Blue - Black

112.1

51.6

Motor Characteristics

Power Supply

Frequency

Power Absorption

Current

120 VAC

60 HZ

144 W

1.2A

Junction boxL NGND

EMIFilter

BK

Y-G

W

W

BK

W

BKW

Y-G

BK

WY-G

BK

BR Y

BR Y GY R BK

W

GY

R

BK

W

BK

BUR BU BK

Y-G

Y-G

25uF

16uF

15uF

Ballast

SE11PA

R

R

BU

BU

Installation Instructions W10320580

3

Jenn-Air


Remove These Screws

Remove These Screws

These ScrewsThese Screws

To remove the LCD display:

1. Disconnect power to the range hood. 2. Remove the range hood from the installation. 3. Remove the glass. See figure 1. 4. Remove the foam insulation from around the top of the range hood flue. See figure 4.

1. Disconnect power to the range hood.2. Remove the range hood from the installation.

3. Remove four (4) T10 Torx screws that secure the two (2) glass retainer brackets.4. Remove two (2) T10 Torx screws from control bracket. See figure 2.

5. Disconnect harness.6. Remove strain relief from the control panel. See figure 3.7. Remove two (2) T10 Torx screws that mount the display to the bracket.

Harness Strain Relief

LCD Display with Bracket

Harness Connector

LCD Display with Bracketwith Bracketwith Bracket


Harness Connector


Figure 2

Figure 1

To remove the motor:

Screws

Remove four (4) T10 Torx screws that secure thetwo (2) glass retainer brackets.Remove two (2) T10 Torx screws from control

Figure 1Remove four (4) T10 Torx screws that secure thetwo (2) glass retainer brackets.

Screws

Remove four (4) T10 Torx screws that secure the

Remove These ScrewsThese ScrewsThese Screws

Glass

Glass Retainer Bracket

of the range hood flue. See figure 4.

Foam Insulation

Intake Cover

Thumb Screws

Filter

Vent Hood Top

FlueFlueFlueFlue

Vent Hood Top

Figure 4

Figure 5

Figure 3

Intake Cover

Thumb Screws Figure 5Thumb ScrewsThumb Screws

Filter

JXI5042WS, JXI5036WS

Motor HousingMotor Housing

LCD DisplayLCD Display

5. Remove two (2) thumb screws to release intake cover at the bottom of the unit. See figure 5.

6. Remove filter. See figure 5.

4

JXI5042WS, JXI5036WS (continued)Jenn-Air

7. Remove (4) T10 Torx screws one in each corner of the filter guard, see figure 6.

8. Remove (4) T10 Torx screws from the motor mounting plate, see figure 7.

NOTE: It is recommended that an extention be used with the screw driver because these screws are difficult to reach. Screws also may be obstructed by insulation. If this is the case, move the insulation out of the way and replace it when reassembling.

9. Loosen or remove (2) T20 Torx screws (one on each side) that mounts the motor into “key

hole” slots at the top of the range hood, see figure 8 and 9.

NOTE: The “key hole” screws are covered by a piece of foam insulation. Be sure to replace the insulation when reassembling.

10.Position the motor so that the screw heads clear the “key hole”slots and remove the motor.

Figure 6

Figure 7

Figure 8

Figure 9

Figure 10

Remove These Screws

Top of Hood

Back of Motor removed from Hood

Key Hole Slot

Foam Insulation

Figure 8Figure 8

T20 Torx

5

Wiring DiagramJenn-Air

JXI5042WS, JXI5036WS (continued)

12

WIRING DIAGRAM

NL

LA S1S3 S2LN NL NMP8 P7 P6P5P1 P2 P3P4A P4

CON3 CON4

CON1

CON2

Electronic Power Board

Electronic User Interface

12345 123456

WRGYBR

Y

BR

Y-G

BRBR

R

R

BK

BR

R

BR

TRANSFORMERPRI

Y Y

SEC

Y

YTR

ANSF

ORM

ERI

RP

Y YC

ES

GYW R

BK BUBURW G

Y BK1

Y-G

G-Y

BU

WBK

R

G-Y

G-Y

WIRING BOX

Y

Y

Y

Y

ATTENTION!:

ADDITIONAL LAMPS ONLYPRESENT ON THE VERSIONSWITH 4 LAMPS

Y

Y


6

1. Disconnect power to the range hood. 2. Remove the air filters 3. Remove (2) T10 Torx screws from the

underside of the front panel. This is the panel that accommodates the incandescent lights see figure 1.

JXW9030WS, JXW9036WS, JXW9048WSJenn-Air

To remove switches:

4. Remove the knobs 5. Remove the center shaft nuts securing the switches in place. 6. The switches can be removed and disconnected.

Figure 1

NOTE: Be sure to note the position of the locator pins on each switch and orient the switches properly when reassembling, see figure 2 and 3.

Figure 2

Figure 3

The switches can be removed and

Locator Pin Locator Hole


FANINCANDESCENT LIGHTS

HALOGEN LIGHTS

Switch functions

Front Panel(Hologen Lights)

Knobs

7


Wiring Diagram

12

WIRING DIAGRAM

NL


CON3 CON4

CON1

CON2



12345 123456

WRGYBR

Y

BR

Y-G

BRBR

R

R

BK

BR

R

BR

TRANSFORMERPRI

Y Y

SEC

Y

YTR

ANSF

ORM

ERI

RP

Y YC

ES

GYW R

BK BUBURW G

Y BK

1

Y-G

G-Y

BU

WBK

R

G-Y

G-Y

WIRING BOX

Y

Y

Y

Y

ATTENTION!:


Y

Y


Uses a supplemental blower system30-36” W1029400648” W10294026

8

KXI2530YSS, KXW2536YSS, KXW2548YSSKitchen Aid

Glass and Frame

ControlFilter

Motor Housing

glass hold down bracket

Glass


Glass and Frame

Filter Control

Glass

bracket

Motor Housing

MotorMotor

1. Disconnect power to the range hood. 2. Remove the hood from installation. 3. Remove the filters. 4. Remove (4) T20 Torx screws that secure glass hold down brackets (2) screws on either side of the motor housing base, see figure 1.

5. Remove the glass and frame and place it in a secure location.

NOTE: Visually center glass around box (duct) when reassembling.

6. Remove (2) T20 Torx screws from the control, see figure 2.

7. Disconnect harness and remove control, see figure 3.

To remove control:

Figure 1

Figure 2

Figure 3

ScrewsScrews

Remove (2) T20 Torx screws from the control, see figure 2.

ScrewsScrews

ControlConnectors ControlConnectorsConnectorsConnectors

9

To remove motor:

Figure 1

1. Disconnect power to the range hood. 2. Remove the filters. 3. Disconnect the harness. 4. Remove (4) 1/4” screws from the motor mounting bracket, see figure 1.

Screws

Motor

Motor Connector

NOTE: It is recommended that a screwdriver extension be used because these screws

are difficult to reach.

KXI2530YSS, KXW2536YSS, KXW2548YSS (continued)Kitchen Aid

10

Kitchen AidWiring Diagram

12

WIRING DIAGRAM L NGND

BK Y/G W

EMI Filter

WBKBRBUY

WRBK

BK (Line)

BU (Neutral)

Y (Lamp)W (Speed 1)R (Speed 2)

GY (Speed 3)

AGC 02125

Mechanical Push Buttons With Back Light

Switch OperationPosition Connection

Off

Lamps

Low Speed

Medium Speed

High Speed

No Connection

Black - Yellow (1 - 3)

Black - White (1 - 4)

Black - Red (1 - 5)

Black - Gray (1 - 6)

12.5uF

1 2 3 4 5 6 7 8 9

Y/G

BRYWRBKBUBU G

Y

BK R W Y BR Y/G


Blue - Red 37.7

Blue - Gray 30.3

Blue - Black 28.8 (max)

Blue - White 45.1 (min)

Room Temp. 73˚F (23˚C)

Power Supply

Frequency

Power Absorption

120 V AC

60 Hz

240W


Tran

sfor

mer

Tran

sfor

mer

120V

120V

12V

12V

Y BU Y Y Y Y

BU Y Y Y Y Y

BU BU Y

W R

BK Y/G

Y

BU

BK BR W BU Y W R BK Y/G


KXI2530YSS, KXW2536YSS, KXW2548YSS (continued)

11

KXU4236YSS, KXU4230YSSKitchen Aid


1. Disconnect power to the range hood.2. Remove the filters.3. Remove (4) T10 Torx screws from under the

frame, (2) screws at the corner of each side panel, see figure 1.


Figure 1

4. Remove (2) T20 Torx screws, one from each side of the light panel, see figure 2.

5. Disconnect the ribbon cable behind the light panel and remove the panel, see figure 3.

6. Remove (2) T10 Torx screws that secure the switch housing to the frame, see figure 4.7. Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.

Figure 2

Figure 3

Figure 4

Figure 5

T20 Torx

Ribbon Cable

Remove (2) T10 Torx screws that secure the switch housing to the frame, see figure 4.

Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.switch housing, see figure 5. Disconnect ribbon cable.


Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.


Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.



Remove (4) screws that secure the board to the housing to the frame, see figure 4.

Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.switch housing, see figure 5. Disconnect ribbon cable.Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.


Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.Remove (4) screws that secure the board to the switch housing, see figure 5. Disconnect ribbon cable.

Figure 2

T20 Torx

Ribbon Cable

T10 Torx

Ribbon Cable

Control3 Filters Control3 Filters

KXI2530YSS, KXW2536YSS, KXW2548YSS (continued)

12

KXU4236YSS, KXU4230YSS (continued)Kitchen Aid

1. Disconnect power from the range hood. 2. Remove the filters. 3. Remove (4) 1/4” hex head phillips screws from the motor mounting bracket, see figure 1.


Screws

4. Slightly rotate and reposition the motor to disengage the stamped metal “ears” that mate with opening in the motor mounting bracket,see figure 2 and 3.

Figure 1

Figure 2

Figure 3

Figure 2

Locking Tabs Openings(“Ears”)

5. Disconnect electrical plug from the printed circuit board.

Locking Tabs(“Ears”)

13


L GND N Electronic User InterfaceLCD


BE1CAA

W Y/G BK

N N N 4SALL S3 S2 S1

5 4 3 2 1 6 5 4 3 2 1

BKBK

BUBU

GYGY

RR

WW

YY

BRBR

Y/G

Y/G

12.5 uF

BU Y Y Y

120 V

12 V

Trans

form

er

Y

MS50



BU/R 18

BU/GY 14.3

BU/BK 9.8 (max)

BU/W 21.6 (min)

Room temp.

Power supply 120 VAC

Frequency 60 Hz

Power absorption 420 W

Current 3.7 A

1 2 3 4 5 6 7 8 9

N

Y

73.4˚F (23˚C)

KXU4236YSS, KXU4230YSS (continued)


14

KXU8030YSS, KXU8036YSSKitchen Aid


Control2 Filters Control2 Filters

1. Disconnect power from the range hood. 2. Remove the filters. 3. Remove (4) T10 Torx screws from backside of the light panel, see figure 1.

4. Remove (2) T10 Torx screws that secure the switch box to the light panel, see figure 2.


Figure 2

Figure 1

Figure 3

Figure 4

5. Remove the switch housing from the light panel.

6. Remove (4) T10 Torx screws that attach the cover to the switch box assembly, see figure 4.

7. Test and or replace the affected switch.

Remove (4) T10 Torx screws that attach the cover to the switch box assembly, see figure 4.

Figure 4

Test and or replace the affected switch.

Figure 4Figure 4

Screw Locations

Switches

15

KXU8030YSS, KXU8036YSS (continued)Kitchen Aid

a. Disconnect power to the range hood. b. Remove the filters. c. Disconnect quick disconnect plug.

1. To remove the motor:

d. Remove (4) hex head phillips screws from the 2 motor mount brackets, see figures 1 and 2.

Figure 1

Figure 2

Disconnect quick disconnect plug.

Remove (4) hex head phillips screws from the 2 motor mount brackets, see figures 1

Figure 1

2 motor mount brackets, see figures 1

Remove These Screws

Remove These Screws

Quick Disconnect

16


12

WIRING DIAGRAM

TemperatureSensor


Blue - Red

Blue - Gray

Blue - Black

Blue - White

Room Temp.

18

14.3

9.8 (max)

21.6 (min)

41˚F (23˚C)


Power Supply

Frequency

Power Absorption

Current

120 VAC

60 HZ

420 W

3.7A

Junction BoxGND L N

Y/G BK W

W W

Y

Y

W

BU BR

BK

Fan Speed Fan Light

On OffOffG

Y R W BK BR Y BK Y

R R

Y

BR BR

BK

Speed 3

Speed 2

Speed 1

BR

W

BK GYBU W

Y BR

Y/G

25uF

Y/G

BRYWRBKGY

BU

KXU8030YSS, KXU8036YSS (continued)


17


KXW2330YSS, KXW2336YSSKitchen Aid

ControlFilters ControlFilters

1. Disconnect power from the range hood. 2. Remove the filters. 3. Disconnect control and harness connector, see figure 3.

1. Disconnect power to the range hood. 2. Remove the filters. 3. Remove (2) T10 Torx screws from the right underside of the light panel, see figure 1.

4. The control can now be easily accessed , see figure 2.

5. Disconnect the control harness, see figure 2.



Screws

Control

Figure 1

Figure 2

Control Harness Connector

Disconnect power from the range hood.Remove the filters.Disconnect control and harness connector, see figure 3.

Harness Connector

Figure 3

Figure 4

Left side of motor Right side of motor

4. Remove (4) T10 Torx screws from the motor mounting plate (2) on each side, see figure 4.

5. Disengage locating “ears” from the slots at the back of each bracket, see figure 4.Disengage locating “ears” from the slots at the back of each bracket, see figure 4.the back of each bracket, see figure 4.

Right side of motorLeft side of motor

Remove These Screws

Ears

Ears

18

KXW2336YSS, KXW2330YSS (continued)Kitchen Aid

Figure 3

Figure 4

7. Remove (6) T10 Torx screws that mount the electrical housing around the motor, see figure 4 and 4a.

9. Disconnect motor wiring harness from connector block and remove motor, see figure 6.

6. Pull motor out, see figure 3.

Figure 5

Figure 4a

Figure 6Screws

Screws

Disconnect motor wiring harness from connector block and remove motor, see figure 6.connector block and remove motor, see figure 6.

Connector Block Motor Wiring Harness

Tabs

Screws

8. Remove (2) T10 Torx screws and disengage (2) tabs that secure the wiring harness cover, see figure 5.

19

KXW2336YSS, KXW2330YSS (continued)Kitchen Aid

Wiring Diagram

12

WIRING DIAGRAMJunction box

L NGND

BKBK

BKBK

BKBK

BK

BK

BK (Line)

BU (Neutral)

Y (Lamp)

W (Speed 1)

R (Speed 2)

GY (Speed 3)

AGC 02125

Mechanical pushbuttonswith back light

Y/G W

Y/G W

WW

BRBR Y

Y

RR G

YG

YEMIFilter

RR

YBU

Transformer120 V

12 V

Y/G

Y/G

Y/G

BR

BR

WW

W

RRBU

BU

GY

GY

W

Y

N

12.5 uF

1 2 3 4 5 6 7

1

1

2

2

3

3

4

4

5

5

6

6

Motor resistance (Ohms)

Switch operation

Motorcharacteristics

Position Connection

Off No connection

LampsBK/Y(1-3)

Low speed BK/W(1-4)

Medium speed BK/R(1-5)

High speed BK/GY(1-6)

BU/R 37.7

BU/GY 30.3

BU/BK

BU/W

Room temp.

28.8 (max)

45.1 (min)

73.4˚F (23˚C)

Power supply

Frequency

Power absorption

120 VAC

60 Hz

240 W


20

KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSSKitchen Aid


1. Disconnect power from range hood. 2. Remove the filters. 3. Remove (2) T10 Torx screws each from the right and left of side panels total of (4), see figure 1.

4. Remove (4) T10 Torx screws, (2) from each side ofthe light panel, total of (4), see figure 2.

5. Remove (2) T10 Torx screws, that secure the on/off switch bracket to the frame, see figure 3.

6. Depress the switch retainers and pull the switch out the front of the panel. See figure 4.

To remove the light switch and control:

2 Filters

Motor

KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS

Motor

2 Filters Control

Figure 1

Figure 2

Figure 3

Remove these screws

Side Panels

Remove (2) T10 Torx screws, that secure the on/off switch bracket to the frame, see figure 3.

Figure 2

on/off switch bracket to the frame, see figure 3.Remove (2) T10 Torx screws, that secure the on/off switch bracket to the frame, see figure 3.

On/Off Switch

Light Panel

Light Switch

Figure 4

Screws

Switch Bracket

Figure 4

Switch Bracket

Light Switch

Strain Relief

Light Panel

21

Figure 6

Figure 5Figure 5

Remove Screws at these Locations

Control Bracket

7. Remove (2) T10 Torx screws to release the control bracket, see figure 5.

9. Remove (4) T10 Torx screws from the Electronic User Interface board and disconnect ribbon connector, see figure 6.

8. Remove (2) T10 Torx screws from the control box cover, see figure 6.

Remove (2) T10 Torx screws from the control Remove (2) T10 Torx screws from the control cover, see figure 6.

Remove (2) T10 Torx screws from the control Remove (2) T10 Torx screws from the control cover, see figure 6.

Remove Screws at these Locations

Ribbon Connector

Kitchen AidKXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS (continued)

22

12

WIRING DIAGRAM



Power Supply

Frequency

Power Absorption

Current

120 VAC

60 Hz

420 W

3.7 A

Blue - Red

Blue - Gray

Blue - Black

Blue - White

Room Temp.

18

14.3

9.8 (max)

21.6 (min)

73˚F (23˚C)



KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS (continued)

23


2 Filters2 Filters Control

1. Disconnect power from range hood.2. Remove the filters.3. Remove (4) T20 screws along the underside

edge of the front filter retainer, see figure 1.

4. Remove (2) screws, one at each end of the front filter retainer panel, see figure 2.

To remove the control switch:

Figure 1

Figure 2

Figure 3

5. Remove (2) screws, one on each side of the filter retainer panel, remove the panel, see figure 3.

6. Remove (2) screws, one at on each side of the control switch, see figure 4.

Disconnect power from range hood.Remove the filters.Remove (4) T20 screws along the underside edge of the front filter retainer, see figure 1.

Remove (2) screws, one at on each side of the control switch, see figure 4. Remove (2) screws, one at on each side of the control switch, see figure 4.

Figure 3

Remove (2) screws, one at on each side of the control switch, see figure 4.

Remove These Screws

Figure 4

Figure 5

Figure 6

KXW8730YSS, KXW8736YSS, KXW8748YSSKitchenAid

Remove These Screws

Front Filter Retainer Panel

Figure 6Figure 6Figure 6Figure 6

Screw Locations

Switches

7. Remove the control switch from the light panel.

24

KXW8730YSS, KXW8736YSS, KXW8748YSS (continued)Wiring Diagram

16

WIRING DIAGRAM

SE112A

Junction box

N L Gnd

Y-G

WBK

GY R W GY R W R BK BR R BK BR BU BK Y

BU BK

RR

Temperaturesensor

Closuretemperature:167˚F±5.4˚F

(75+/-3˚C)Opening

temperature:≥140˚F (60˚C)

W W

W

R R

R

W

R

BK

RBR

BU

Fan speed Fan speed Fan speedOn Off On Off Off

1

24

3

6

7 5

8

1231

24

3

6

7 5

8

1231

24

3

6

5Fan

1

24

3

6

5 1

24

3

6

7 5

8

12

Light

Speed 1

Speed 2

Speed 3

BU BK GY

W

BU BK GY R W Y-G

25uF 25uF

BRBRBR BR

Y Y BU GYBK R W

Y/G

1 2 43 65

1 2 43 6 75 8 9 10

12

43

65

W Y

W WWY

BUY

BU

LampsOptional kit with 1 motor


Switch operation with button “1-2-3”Position

Connection

Action

Switch operation with button “ON-OFF”

Position

Connection

Action

Position

Connection

Action

Switch operation with button “Light”


Blue-Red: 18

Blue-Gray: 14.3

Blue-White: 21.6 (min.)

Room Temp: 73.4˚F (23˚C)

Blue-Black: 9.8 (max)

1 2

4

3

6 52 4 7

Speed 1 Speed 2 Speed 3

46 24

Motor ON Motor OFF

ON OFF 1 2OFF

4 62 47

6 85

Power supply: 120 VAC

Frequency: 60 Hz

Power absorption: 420 W

Current: 3.7A

Lights Off LowIntensity

HighIntensity

Y


25

KXI9736YSS, KXI9748YSSKitchen Aid


Control

3 Filters

Control

3 Filters

Motor

KXI9736YSS, KXI9748YSSKitchen Aid

Motor

1. Disconnect power from the range hood. 2. Remove the filters. 3. Remove (2) T10 Torx screws that mount the control, see figure 1.

NOTE: Some models may require that a separate blower motor is purchased to meet the installation specifications.

6. Remove and/or replace the switch(es) as needed.

5. Remove (6) T10 Torx screws from the control switch cover, see figure 2.


Figure 1

Figure 2

Figure 3

4. Pull the control out from the back of the panel, see figure 2.

26

KXI9736YSS, KXI9748YS (continued)Kitchen Aid


17

WIRING DIAGRAM

SE110A

Junction box

N L Gnd

Y-G

WBK

RBR


(75+/-3˚C)Opening


Temperaturesensor

W WW

Y

BUY

BU

Y

W Y

Lamps


Blue-Red: 18

Blue-Gray: 14.3





Connection

Action

1 2

4

3

6 52 4 7



Position

Connection

Action

46 24

Motor ON Motor OFF

ON OFF Position

Connection

Action

Switch operation with button “Light”1 2OFF

4 62 47

6 85


HighIntensity



Frequency: 60 Hz


Current: 3.7A

Optional kit with 1 motor

25uF

BRBRBR BR

25uF

1 2 43 6 75 8 9 10

Y Y BU GY

BK R W Y/G

BU BK GY R W Y-G

1 2 43 65

BU BK GY

W

Speed 1

Speed 2

Speed 3

R R

RRG

Y R W

R R

GY R W R BK BR R BK BR

1

24

3

6

7 5

8

123

Fan speed1

24

3

6

7 5

8Fan speed

123

FanOn Off

1

24

3

6

5Fan

On Off1

24

3

6

5

BU BK

BU BK Y

Off 1

24

3

6

7 5

8

12

Light

W

BK

W WW

BU

1 2 43

1 2 3

Wiring Diagram

27

NOTES

28

In-Line, Internal and External Blower Systems

These are dedicated blowers designed to work with the range hood models listed below. Blower models and mounting locations are determined at the time of installation. Blowers are matched to range hood models based on individual installation requirements.

Internal Blower Models (inside frame of hood)

In-Line Blower Models (outside the frame of the hood, but in

the exhaust vent system)

External Blower Models(outside the house)

KXI9736Y KXI9748YKXW8730Y KXW8736Y KXW8748YKXW9736Y KXW9748YUXL6036YUXL6048Y

Range Hood Models(requires one of the listed blower models

UXB0600D (600 CFM)UXB1200D(1200 CFM)

UXI0600D (600CFM)UXI1200D (1200 CFM)

KPEU722M (600CFM) KPEC922M (1200 CFM)

Range hood models and detecated blower assemblies

29

Internal Blower Systems

To remove internal blower motor:

Single Internal Blower Motor Assembly

1. Disconnect power to the range hood.

2. Remove the internal blower motor assembly inside the hood liner canopy.

9

Install Hood Liner Internal Blower Motor

1. Install the hood liner blower motor assembly inside the hood liner canopy with the wiring connection to the left for the single motor system and to the front or top for the dual motor system.

Single Blower Motor Assembly

Dual Blower Motor Assembly

2. Slide the left mounting plate flange under the motor mounting bracket.

3. Run the power supply wires and connector from the range hood through the hole in the right end of the motor mounting plate.

4. Push the right end of the motor mounting plate up and snap it into the spring tab.NOTE: The spring tab should be outside the slot in the mounting plate.

5. Align mounting holes in motor mounting plate with motor mounting clip nuts and install 6 x 16 mm screws and 6.4 mm lock washers (quantity 2 for single motor; quantity 5 for dual motor).

A. Wiring connection


A. Motor mounting bracketB. Mounting plate left flange

A

A

BA

A. Motor mounting plate holeB. Power supply wires and connector

A. Motor mounting plateB. Spring clip

A. Screw with lock washerB. Mounting hole in motor mounting plateC. Clip nut (6 mm)

A

B

A

B

A

B

C

9












A

A

BA




A

B

A

B

A

B

C

9












A

A

BA




A

B

A

B

A

B

C

4. Slide the left mounting plate flange from under the motor mounting bracket.

3. Disconnect the motor wiring harness from the locations shown for a single or Dual blower motor system. See marked locations “A”.


Internal Dual Motor Assembly

UXB0600D, UXB1200D, UXI600D, UXI1200D

UXB0600D (600 CFM)

UXB1200D (1200 CFM)

Internal Blower Models (inside frame of hood)

In-Line Blower Models (outside the frame of the hood, but in

the exhaust vent system)

External Blower Models(outside the house)

KXI9736Y KXI9748YKXW8730Y KXW8736Y KXW8748YKXW9736Y KXW9748YUXL6036YUXL6048Y

Range Hood Models(requires one of the listed blower models

UXB0600D (600 CFM)UXB1200D(1200 CFM)

UXI0600D (600CFM)UXI1200D (1200 CFM)

KPEU722M (600CFM) KPEC922M (1200 CFM)

Range hood models and detecated blower assemblies

30

9












A

A

BA




A

B

A

B

A

B

C9












A

A

BA




A

B

A

B

A

B

C

9












A

A

BA




A

B

A

B

A

B

C

5. Remove 6 x 16 mm screws and 6.4 mm lock washers (quantity 2 for single motor; quantity 5 for dual motor).

6. Remove the power supply wires and connector from the range hood through the hole in the

right end of the motor mounting plate.

8. Pull the right end of the motor mounting plate down and unsnap it from the spring tab.NOTE: The spring tab should be outside the slot in the mounting plate.

A. Screw with lock washerB. Mounting hole in motor mounting plate

C. Clip nut (6 mm)

10

6. Attach power cord connector from the range hood to connector on wiring box.

7. Go to the “Make Electrical Power Supply Connection to Hood Liner” section.

Install Hood Liner In-Line (External Type) Blower Motor

NOTE: Your hood liner requires you to purchase either an internal type or an in-line (external type) blower motor system. See “Blower Motor System” in the “Accessories” section.

Prepare for Mounting the In-Line Blower System

The in-line blower system must be fastened to a secure structure of the roof, ceiling, wall, floor, or new or existing frame construction. The 4 holes on either the inlet (bottom) side or the outlet (top) side of the blower must be used to mount the in-line blower system to the structure.NOTE: The mounting hole locations must span the studs. Additional stud framing may be required. Plywood may be used to span open areas between ceiling joists or roof rafters to aid installation. This structure must be strong enough to support the weight of the in-line blower system (50 lb [22.6 kg] min).

Prepare the In-line Blower System

1. Using two or more people, move the in-line blower motor system to the mounting location.

2. Remove the 10 screws from the front cover of the in-line blower motor housing and set them aside.

3. Remove the front cover of the in-line blower motor housing and set it aside.

NOTE: To make the blower motor housing easier to mount, the blower motor assembly can be removed. If you do not want to remove the blower motor assembly, proceed to “Install In-line Blower System” in this section.4. Disconnect the motor electrical plug from the blower motor

assembly.

5. Remove the screws that secure the blower motor assembly to the in-line blower housing and set them aside.

6. Pull the spring clip to release the blower motor assembly. Remove the blower motor assembly from the housing and place it on a covered surface.

Install In-line Blower System

NOTE: The blower motor housing can be mounted using 4 holes from either the inlet side or the outlet side of the blower.

1. Position the in-line blower motor housing in its mounting location and mark the 4 mounting hole locations.

2. Drill 4 mounting pilot holes using a ³⁄₁₆" (5 mm) drill bit.3. Attach the in-line blower motor housing to the mounting

location with four 6 x 80 mm mounting screws and washers. 4. If it is removed, reinstall the blower motor assembly and

secure it with the screws previously removed. 5. If it is removed, reattach the motor electrical plug to the

connector on the blower motor assembly.

A. Wiring box connectorB. Power supply connector

from range hood

B

A

WARNINGExcessive Weight Hazard

Use two or more people to move and install in-line blower motor system.

Failure to do so can result in back or other injury.

A. Front coverB. Blower mounting screwsC. Spring clipD. Bottom housing mounting holesE. Motor electrical plug

A. Mounting holes

A

B C

D

A

A A

A

A

A

Outlet Side

Inlet Side

7. Disconnect power cord connector from the range hood to connector on wiring box.

Internal Blower Systems (continued)UXB0600D, UXB1200D

31

In-Line Blower Systems


1. Disconnect power to the range hood. Use two or more people, to remove the in-line blower motor system from the mounting location.

2. Remove the 10 screws from the front cover of the in-line blower motor housing.


NOTE: To make the blower motor housing easier to remove, the blower motor assembly can be removed first. 4. Disconnect the motor electrical plug from the

blower motor assembly.

10












assembly.











from range hood

B

A





A. Mounting holes

A

B C

D

A

A A

A

A

A

Outlet Side

Inlet Side

To Remove In-Line blower system:

UXI0600D, UXI1200D5. Remove the screws that secure the blower motor

assembly to the in-line blower housing and set them aside.

6. Pull the spring clip to release the blower motor assembly.Remove the blower motor assembly from the housing and place it on a covered surface.

UXI0600D (600CFM), UXI1200D (1200 CFM)


Excessive Weight HazardUse two or more people to move and install in-line blower motor system.Failure to do so can result in back or other injury.

Removing an In-Line Blower System:

32

In-Line Blower Systems (continued)

11

Complete Preparation

1. Determine and make all necessary cuts for the vent system.IMPORTANT: When cutting or drilling into the ceiling or wall, do not damage electrical wiring or other hidden utilities.

2. Determine the location where the ¹⁄₂" (1.3 cm) wiring conduit will be routed through the ceiling or wall between the in-line blower and the hood liner.

3. Drill a 1¹⁄₄" (3.2 cm) hole at this location.4. Locate the electrical terminal boxes in the in-line blower

housing and hood liner. Remove the terminal box covers and set the covers and screws aside.

5. Remove the electrical knockout from the in-line blower housing and hood liner to prepare for the installation of the UL listed or CSA approved ¹⁄₂" (1.3 cm) wiring conduit and conduit connector.

6. With the hood liner mounted (see the “Install Hood Liner” section), run the ¹⁄₂" (1.3 cm) wiring conduit between the in-line blower motor housing and the hood liner. Pull enough ¹⁄₂" (1.3 cm) wiring conduit to allow for easy connection to the terminal boxes in the in-line blower housing and hood liner.

7. Run the six 18 AWG wires through the ¹⁄₂" (1.3 cm) wiring conduit and conduit connectors and into the terminal boxes on the in-line blower housing and hood liner. Leave enough wire length in each terminal box to make the wiring connections.

8. Install the conduit connectors and conduit to the in-line blower housing and hood liner electrical terminal boxes.

9. Connect the vent system to the hood liner and in-line blower system and seal all joints with clamps.

Make Electrical Connections for In-Line Blower Motor System

Electrical Connection Inside In-line Blower System1. Disconnect power.2. Connect the wires from the wiring conduit to the wires from

the motor electrical plug cable inside the in-line blower housing terminal box.

.

3. Use UL listed wire connectors and connect the black wires (C) together.

4. Use UL listed wire connectors and connect the white wires (D) together.

5. Use UL listed wire connectors and connect the red wires (E) together.

6. Use UL listed wire connectors and connect the blue wires (F) together.

7. Use UL listed wire connectors and connect the gray wires (G) together.

A. Electrical terminal boxB. Electrical knockout

AB

A. UL listed or CSA approved ¹⁄₂" (1.3 cm) wiring conduit

B. UL listed wire connectorsC. Black wiresD. White wiresE. Red wires

F. Blue wiresG. Gray wiresH. Green (or yellow/green)

and green/yellow wiresI. Motor electrical plug cable

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

A

BC

D

E

F

GH

I

Disconnect Electrical Connections for In-LineBlower Motor System

1. Disconnect power.2. Disconnect the wires from the wiring conduit leading to the wires from the motor electrical plug cable inside the in-line blower housing terminal box.

10












assembly.











from range hood

B

A





A. Mounting holes

A

B C

D

A

A A

A

A

A

Outlet Side

Inlet Side


1. Detach the in-line blower motor housing from the mounting location by removing four 6 x 80 mm mounting screws and washers.

UXI0600D, UXI1200D

33

External Blower SystemsKPEU722M, KPEC922M


KPEU722M (600CFM) KPEC922M (1200CFM)

To access the external blower motor:1. Disconnect the power to the In-Line blower.2. Remove the blower housing cover.

3. Disconnect the vent work from the exterior blower’s black plastic vent collar and remove duct tape as needed.

4. Remove the wiring box cover and disconnect the 120-volt power supply cable at the strain relief.

5. Remove wire connectors and disconnect the Wiring. (See FIGURE 3 and wiring diagram.)• Using twist-on connectors:• Disconnect white wires.• Disconnect black wires.• Disconnect the green power supply wire.

Disconnect the vent work from the exterior blower’s black plastic vent collar and remove duct Disconnect the vent work from the exterior

Blower Housing Cover

Motor and Fan Assembly

Black Plastic Collar

Figure 3

Parts List


Excessive Weight HazardUse two or more people to move and install in-line blower motor system.Failure to do so can result in back or other injury.

34

External Blower Systems (continued)KPEU722M, KPEC922M

Wiring Diagram

Installation Instructions 8285496

35

Additional Range Hood Wiring Diagrams

ADDITIONAL RANGE HOOD WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35JXI8042W, JXI8036W, JXI8242W, JXI8236W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36JXW5030WS, JXW5036WS Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37JXW6030W, JXW6036W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38JXW8030W, JXW8036W, JXW8042W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39JXW8230W, JXW8236W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40JXW8836W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41JXW9030WS, JXW9036WS, JXW9048WS Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42KXI9736Y, KXI9748Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43KXU2830Y KitchenAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44KXI2536Y, KXI2536Y KitchenAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45UXL6048YSS,UXL6036YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

UXG7360VD, UVG73660VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

36

Models: JXI8042W, JXI8036W, JXI8242W, JXI8236W Additional Range Hood Wiring Diagrams (continued)

Installation Instructions W10274319E

13

WIRING DIAGRAM

Y

BR

321 4 5 6

LA S1S3 S2

7 8 9

Y/GBU Y/

G

BRYL

LN NL NMP8 P7 P6

W

BK

WRGY BK

WRBK

BU

P5P1 P2 P3P4A P4

CON3 CON4

CON1

CON2



CON 6

CON 5

12345 123456

CON7

CON8

S4P9

GY

NLGND

Y/G

N L CON 11

CON 12

BU

N L CON 9

CON 10

BUBU

BU

BU

YY

Y

Y

BU Y

BU Y

BUBU YY

BU BUY Y

WBK

37

JXW5030WS, JXW5036WSJenn-Air


14

WIRING DIAGRAM

NL


CON3 CON4

CON1

CON2



12345 123456

WRGYBR

Y

BR

Y-G

BRBR

R

R

BK

BR

R

BR

TRANSFORMERPRI

Y Y

SEC

Y

YTR

ANSF

ORM

ERI

RP

Y YC

ES

GYW R

BK BUBURW G

Y BK1

Y-G

G-Y

BU

WBK

RG-

Y

G-Y

WIRING BOX

Y

Y

Y

Y

ATTENTION!:


Y

Y

Additional Range Hood Wiring Diagrams (continued)

38

Additional Range Hood Wiring Diagrams (continued)JXW6030W, JXW6036W

Jenn-Air


12

WIRING DIAGRAM

2 4 6 8 10

1 3 5 7 9

SE1Q7A

TRANSFOR-MER

12V

120V

SPEED 1 2 3

8-103-5 5-7

Fan Speed Cont. Brd (FSCB)

0 1

2-4 4-6

1-3 3-5

Light Cont. Brd (LCB)

YEL

Y

Y-G

W

WBK

Y-G

BK

BK

RR

COLOR TABLE

BR

GY

BKBU

G

Y-G

R

Y

W

RED

COLOR TABLE

3 2 1

MOTORSPEED

1

CONNECTIONSTO TERMINALS

2

3

FSCB1

2

3

4

5

6LCB

BU

GY

BR

Y-G

BL

BU

BL

BK

BR

BR

BR

BR

BU

BK

BU BU

BU

BU

BK

BR

BR

W

BK

Y

R

R

Y-G

CONTACT

39


JXW8030W, JXW8036W, JXW8042WJenn-Air


12

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To avoid damage or decreasing the life of the new bulb, do not touch bulb with bare fingers. Replace bulb, using tissue or wearing cotton gloves to handle bulb.If new lamps do not operate, make sure the lamps are inserted correctly before calling service.1. Disconnect power.2. Push up on the lens and turn it counterclockwise.

3. Remove the bulb and replace it with a 120-volt, 50-watt maximum halogen bulb with a GU10 base. Turn it clockwise to lock it into place.

4. Repeat steps 2-3 for the other bulb if needed.5. Reconnect power.

WIRING DIAGRAM

M

Y

BR

321 4 5 6

LA S1S3 S2

7 8 9

Y/G

BU

Y/GB

R

Y

LN NL NMP8 P7 P6

W

BK

WRGY BK

WRBK

BU

P5P1 P2 P3P4A P4

CON3 CON4

CON1

CON2



CON 6

CON 5

12345 123456

CON7

CON8

Y

BU

Y

BU

S4P9

GY

NLGND

Y/G

N LN L

N L CON 13

CON 14

CON 15 CON 16

BU

BE1CAA

BE1EWA

40

JXW8230W, JXW8236WJenn-Air


12

6. Install cleaned or replacement filter. Push charcoal filter handles in and push filter into motor housing frame. Release handles.

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To avoid damage or decreasing the life of the new bulb, do not touch bulb with bare fingers. Replace bulb, using tissue or wearing cotton gloves to handle bulb.If new lights do not operate, make sure the lamps are inserted correctly before calling service.

1. Disconnect power.2. Use a flat-blade screwdriver and gently pry the light cover

loose.

3. Remove the lamp and replace with a 12-volt, 20-watt maximum, halogen lamp made for a G-4 base.

4. Replace the light cover.5. Reconnect power.

WIRING DIAGRAM

M

Y

BR

321 4 5 6

LA S1S3 S2

7 8 9

Y/G

BU

Y/GB

RY

LN NL NMP8 P7 P6

W

BK

WRGY

BK

WRBK

BU

P5P1 P2 P3P4A P4

CON3 CON4

CON1

CON2



CON 6

CON 5

12345 123456

CON7

CON8

TRANSTOR-

MATEUR

12V

120V

Y

YY

BU

Y

S4P9

GY

NLGND

Y/G


41

JXW8836WJenn-Air


13

WIRING DIAGRAM

BK

BU

BR

G

GY

Y/G

Y

W

R

COLOR TABLE COLOR TABLE



Y/G

BK

WRGY

BK

BK

WBK

BK

W W W

BR B

U W

Y/G

BUBR

BK

GY

RWBU

W

BK

W

BK

Y/G

W

R

GY

BKNL


42



17

WIRING DIAGRAM

Junction boxN L Gnd

Y-G

IR switch

Switch

WBK

RBR

Temperaturesensor


(75+/-3˚C)Opening


W WWY

BUY

BU

Y

12

43

65

W Y

Lamps

Motor Resistance (Ohms)Blue-Red: 18

Blue-Gray: 14.3




Switch operation with button “1-2-3”PositionConnection

Action

1 2

4

3

6 52 4 7



Position

Connection

Action

46 24

Motor ON Motor OFF

ON OFF Position

Connection

Action


64 2 47

6 85


HighIntensity



Frequency: 60 Hz


Current: 3.7A


BR BR Y Y BU GY

BK R W

Y/G

1 2 43 6 75 8 9 10

25uF

BRBR

25uF

BU BK GY R W Y-G

1 2 43 65

Speed 1

Speed 2

Speed 3

BU BK GY W

W WW

BU

R W

R

R R

R

GY

1

24

3

6

7 5

8Fan speed

1

24

3

6

7 5

8Fan speed

GY R W

R

R BK BR

On Off1

24

3

6

5Fan

R BK BR

On OffFan

1

24

3

6

5

BU BK Y

BU BK

1

24

3

6

7 5

8

Off12

PositionConnectionAction

1 2

W

BKIR lamps

Switchoperation

ON OFF

Light ON Light OFF

Noconnection

R

Light

Optionallamp used

in 48" (121.9 cm)size hood


43

KXI9736Y, KXI9748YKitchenAid



SE110A

Junction box

N L GndY-G

WBK

RBR


(75+/-3˚C)Opening


Temperaturesensor

W WW

Y

BUY

BU

Y

W Y

Lamps


Blue-Red: 18

Blue-Gray: 14.3





Connection

Action

1 2

4

3

6 52 4 7



Position

Connection

Action

46 24

Motor ON Motor OFF

ON OFF Position

Connection

Action


4 62 47

6 85

Lights O� LowIntensity

HighIntensity



Frequency: 60 Hz


Current: 3.7A


25uF

BRBRBR BR

25uF

1 2 43 6 75 8 9 10

Y Y BU GYBK R W Y/G

BU BK GY R W Y-G1 2 43 65

BU BK GY W

Speed 1

Speed 2

Speed 3

R R

RRGY R W

R R

GY R W R BK BR R BK BR

1

24

3

6

7 5

8

123

Fan speed1

24

3

6

7 5

8Fan speed

123

FanOn O�

1

24

3

6

5Fan

On O�1

24

3

6

5

BU BK

BU BK Y

O� 1

24

3

6

7 5

8

12

Light

W

BK

W WW

BU

1 2 43

1 2 3

44

KXU2830YKitchenAid


14

WIRING DIAGRAM

M

N

LTra

nsfor

mer

Prim

ary

Seco

ndar

y

SEL0015013

1

Motor CharacteristicsPower Supply

Frequency

Power Absorption

120 V

60 Hz

230 W

User Interface

Main Board

EMC

Filt

er

Motor Resistance (Ohms)Speed

1

2

3

4

BU/W

BU/R

BU/GY

BU/BK

Room Temp.

45.1 Min.

37.7

30.3

20.8 Max.

73.4˚ F (23˚ C)

Y

Y

Y Y

Y Y

Y Y

YY

YY

BK

BK

BKBK

BKBK

GY

GYGY

R

RR

R R

W

W

W W

BU

BUBU

WW

Y/G

Y/GY/G

Y/G

BR BR

BRBR

Speed 4

Speed 3Speed 2

Speed 1

Lamp

NeutralNeutral

NeutralL1


45

KitchenAid


Additional Range Hood Wiring Diagrams (continued)KXW2536Y, KXW2530Y

46Installation Instruction W10331011

UXL6048YSS, UXL6036YSSKitchenAid


Wiring Diagram

47

UXG7360VD, UVG73660VDKitchenAid


Installation Instruction W10153187

Wiring Diagram

range hoods - amazon s3 jenn-air whirlpool technical education prepared by: whirlpool consumer care...

Documents