Raisecom RC951E-4FEE1

Ethernet over PDH Remote Gateway

Content

Introduction

Applications

Technical Data

Configure EoP

RC951E-4FEE1

INTRODUCTION

Introduction RC951E-4FEE1

• Raisecom RC951E-4FEE1 is Raisecom's intelligent Ethernet Demarcation Device (EDD) with E1 uplink.

• RC951E-4FEE1 offers 4 FE downlink ports and 1 E1 uplink.

• The device can be either deployed in a point to point topology, or in a point to multi-point topology as CPEs.

• Raisecom EDD is not only capable of doing what a layer-2 switch is capable of on Ethernet switching, but is inherently good at network diagnostices as a device working on the border.

• Apart from local CLI management, RC951E-4FEE1 is also available with inband web-based management.

RC951E-4FEE1

Applications

Point to point

Point to multipoint

Point-to-point application with E1 uplink

Point-to-multipoint application with E1 uplink

RC951E-4FEE1

Technical Data

RC951E-4FEE1 Technical Data (1/2)

• Single VCG, HDLC/GFP encapsulation software configurable

• Support LCAS, VCG members automatically adjust when E1 link status changes

• VCG-level fault pass through• E1 loopback detection and Ethernet loop

detection• Ethernet cable diagnostics• Ingress rate limit and egress traffic shaping

RC951E-4FEE1 Technical Data (2/3)

• Storm control of broadcast, multicast, unicast and dlf frames

• 8K MAC address table, full MAC address table management

• IEEE802.1Q and IEEE802.1ad, VLAN tagging and stacking

• 4 queue QoS, CoS/DSCP/port-based, queue scheduling rule including sp, wrr, sp+wrr

• IEEE802.3ad link aggregation• Layer 2/layer 3 SLA

RC951E-4FEE1 Technical Data (3/2)

• IEEE802.3ah OAM• IEEE802.1ag CFM, and ITU-T recommendation

Y.1731• CLI management access by local CONSOLE,

Telnet or SSH• In-band web-based management• GUI-based concentratively management on

Raisecom NView NNM system

RC951E-4FEE1

Configure EoP

Configure EoP

E1

Carrier Ethernet Backbone

VLAN 110

IP: 192.168.1.10

RC953-4FEE1

E1RAISECOMRC953-FE8E1

E1

IP：192.168.1.11 VLAN：100

E1RAISECOMRC953-FE8E1

SDH

VLAN 110

IP：192.168.1.12 VLAN：100

RC953-4FEE1

•GFP encapsulation mode•Client 1-4 correspond to FE port 1,2,3,4•Line 1 corresponds to inner switch port aggregate traffics from FE port 1, 2, 3, 4. It work under ‘trunk mode’ .•Data traffics using VLAN 110.•Make sure the E1 are contained in the VCG•Remotely manage RC953-4FE8E1 by telnet from central management sever PC Configure IP address 192.168.1.12/24 and 192.168.1.11/24 and VLAN ID 100.•Line 1 trunk allows VLAN 100 to pass as well as other VLANs of traffics.

Configure EoP

Login to RC953-4FEE1Via Serial

Configure EoP (serial)

Login to RC953-4FEE1

Login : raisecomPassword : Raisecom Priviliege Mode

Password : raisecom

Configure EoP (serial)

Create Vlan

GFP Mode

Configure EoP (serial)

Line 1 (E1) for Trunk

Port 1 for vlan 100, port 2 for vlan 101

Configure EoP (serial)

Interface EoP

Enable VCAT

Enable LCAS

Save Configuration

Configure IP Management

Set IP address

IP Address Subnet MaskVlan Management

Configure EoP

Login to RC953-4FEE1Via Web Browser

IP : 192.168.4..30/24

Configure EoP (Web Browser)

Login to RC953-4FEE1

IP :192.168.4.28/24

User Name : raisecomPassword : raisecom

Configure EoP (Web Browser)

Create Vlan1

2

3

4

Configure EoP (Web Browser)

GFP Mode

1

2

3

4

Configure EoP (Web Browser)

Line 1 (E1) for Trunk 1

2

3

4

5

Configure EoP (Web Browser)

Port 1 for vlan 100, port 2 for vlan 101

1

2

3

4

5

6

Configure EoP (Web Browser)

VCG Member1

2

3

4

Configure EoP (Web Browser)

Enable VCAT1

2

3

4

Configure EoP (Web Browser)

Enable LCAS1

3

2

54