workshop solutions special offers - sykes …sykes-pickavant.com/downloads/sykes-pickavant - q2 2014...

SPECIAL OFFERS

NEW PRODUCTS

APRIL - JUNE 2014

INCLUDES AIR TOOLS, BRAKING, COOLING, PULLERS, SUSPENSION, TIMING, WORKSHOP TOOLS & MUCH MORE!

www.sykes-pickavant.com

Workshop Solutions

DR

IVET

RA

IN

1

ww

w.s

ykes

-pic

kava

nt.c

om0855030008550500

38360000

01370300

016795V2

GM Gearbox Bearing / Race Remover• For the removal of taper bearing cups from clutch housings in M32, MT 20-6 and MT 32-6 manual gearboxes• Specifically designed to spread the load equally without danger of cracking the gearbox casing • Applications: Widely used in GM, Saab and Fiat Group

5th Gear Puller - Ford• Fast and simple method of removing the fifth gear on Ford front wheel drive transmissions before carrying out internal repairs• The split collar and retaining sleeve ensures a safe and positive locationApplications:• B5 Gearboxes: Manual 5 speed fifth gear puller (pre -1995) • IB5 from 1995 – present: Fiesta to date / Ka 1 ‘96 – ‘08 • MTX-75: Focus 1, 2 & 3 Zetec engines (inc C Max 1) / Mondeo / Jaguar X Type• VXT-75: Galaxy 1 1995 – 2006 / Transit FWD & Transit Connect to date

Universal Engine & Gearbox Support• Designed to support the engine or gearbox when the engine mountings have been removed - e.g. When replacing timing / drive belts, water pumps etc• Removes the need for using cranes, transmission jacks etc• The unit is suspended from the chassis via the support hooks, the engine / gearbox is supported by the support pad and is counter-balanced against the underside of the vehicle by the support arms• Fully adjustable in all dimensions: - Extension: Min 630mm / Max 960mm - Support Plate Adjustment: 190mm

Scan the QR code to watch a video of the GM

Gearbox Bearing / Race Remover

Scan the QR code to watch a

video of theUniversal Engine & Gearbox Support

Universal Clutch Alignment Tool Kit• For modern front wheel drive vehicles with or without pilot / spigot bearings with flywheel fitting diameters from 12 – 20mm• The tools main advantage is that it includes parallel expanding supports in place of more traditional tapered fittings that are hard to keep located• Easy to swap over adaptors suitable for clutch centre sizes from 14.4 to 29mm• Includes small cone: 14.4 - 21mm, large cone: 20.9 - 29mm and sleeves: 12, 14, 15, 16, 17, 18, 19, 20mm

Alternator Free Wheel Pulley Set - 29 Piece• Special set of Spline & Torx Socket Bits for the removal of free-wheel alternator pulleys• Locks the alternator, allowing the central locking bolt of the pulley to be released• Selection of 33 tooth reaction nuts and additional adaptors• Updated 29 piece set covers a wide range of popular applications including: BMW, Citroën, Fiat, Ford, Mercedes, Opel, Peugeot, Porsche, Renault, Toyota, VW Group, Vauxhall, Volvo• Applications list included - Visit www.sykes-pickavant.com for full details

OFFER €51.50SAVE €13.00

LIST PRICE €64.50

OFFER €102.95SAVE €26.00

LIST PRICE €128.95

OFFER €89.95SAVE €38.00


€115.95

€320.95

DIE

SEL

INJE

CTI

ON

REM

OVA

L

2

Tel:

0154

3 67

9900

185800V2

08585000

185800V2PP

01513500

Hydraulic Injector Puller Kit• 10 tonnes Hydraulic Hollow Cylinder provides the force – use with standard hydraulic pump (not supplied)

Electronic Diesel Injector Removal Socket Set• Hexagonal socket set for removal of the electrical solenoid from modern diesel injectors• 1/2” sq dr. x 78mm length• In most cases, it is necessary to remove the solenoid before attempting to remove the injector body• Includes 4 x sockets:- 25mm Hex – Siemens Injectors - 2.0 Hdi (DW Series) As found on PSA, Ford, Toyota etc- 27mm Hex – Siemens Piezo Injectors – 2.0 Hdi Piezo (DW Series) As found on PSA etc- 29mm Hex – Bosch type injectors – Bosch Cdi / Hdi engines- 30mm Hex – Bosch type injectors – Bosch Renault / Nissan 1.9dCi

€1541.50

€1283.50

€1741.50

Hydraulic Injector Puller Systems• A NEW concept for the removal of stubborn injectors• Provides controlled force to aid the removal of seized injectors where there is insufficient access for traditional slide hammers• Uses a multi-position frame, with adjustable legs of different lengths and a selection of mounting adaptors to allow alignment of the tool with the injectors on a wide variety of modern diesel engines• The combination of variable leg lengths and selection of the appropriate adaptor for the cylinder head, allows the tool to be correctly positioned on most cylinder heads• Supplied with injector adaptors for most modern injector types: M14 | M16 | M17 | M20 | M25 | M27

UPDATED KIT

UPDATED KIT

185810V2Mechanical Hydraulic Injector Puller Kit• As per 185800V2 kit above but includes a mechanical hydraulic ram • Allows use of the kit without the need for a separate hydraulic pump

UPDATED KIT

OFFER €74.95SAVE €15.55

LIST PRICE €90.50

OFFER €315.95SAVE €64.55


Each kit now includes a set of solenoid sockets (01513500) and

2 x tamperproof sockets

Heavy Duty Slide Hammer Injector Remover Kit• Heavy Duty Slide Hammer puller for removal of Bosch, Delphi, Denso and Siemens injectors• Features a flexible u-joint adaptor for access in restricted areas• Contains: - 6 x Injector adaptors: M14 x 1.5, M16 x 1.0, M17 x 1.0, M20 x 1.0, M25 x 1.0, M27 x 1.0 - 4 x Injector Solenoid removers: M25, M27, M29, M30 - 2 x Nozzle Extractors: 6mm Tamperproof: 10mm hex - 7mm Tamperproof: 10mm hex• Heavy Duty Slide Hammer - Hammer Weight: 5.0kg (Total Weight: 8.0kg)• Supplied in blow-moulded case

Hydraulic Injector Puller Kit with Hydraulic Pump • As per 185800V2 kit above but includes aluminium bodied hand pump - 2 Speed, 10,000psi fitted with gauge, hydraulic hose and ¾” hydraulic coupler

HU

B P

ULL

ERS

3

ww

w.s

ykes

-pic

kava

nt.c

om

08530600

085300SP

08531600

08530000

12731100 08251900

Slide Hammer Hub PullerIncludes:• Hub Puller Plate (08530870)• Adaptor for Slide Hammer (08531270)• Slide Hammer 5/8” UNF x 1.6Kg (08530700)

Hydraulic Hub Puller KitConsists of manual and hydraulic components Includes: • Specially designed extra-wide hub puller plate• Hydraulic ram c/w nose piece• Mechanical Screw - 5/8” UNF x 140mm x 24mm hex• Slide Hammer - 5/8” UNF x 1.6kg

Hydraulic Hub PullerIncludes:• Hub Puller Plate (08530870)• Hydraulic Ram c/w nose piece (15000070)

Mechanical Hub PullerIncludes:• 08530870 - Hub Puller Plate• 08531270 - Adaptor for Mechanical Screw• 08531100 - Mechanical Screw - 5/8”UNF x 4” x 24mm Hex

Impact Force Screw• Can be used in any SP Hub Puller in place of Hydraulic Ram or Slide Hammer (11/2”BSW thread)• Use in conjunction with 08251900 Shock Handle (right)

Shock Handle• Use in conjunction with 12731100 Impact Force Screw (left) - allows for greater force to be applied

OFFER €146.50SAVE €29.45


OFFER €138.95SAVE €27.00


OFFER €245.00SAVE €51.95


OFFER €38.95SAVE €9.55

LIST PRICE €48.50

OFFER €51.50SAVE €22.45

LIST PRICE €73.95

OFFER €84.50SAVE €18.00


STAR BUY

12730600

Hydraulic & Mechanical Hub Puller Kit• Can be used on a variety of wheel stud pattern applications - 4, 5, 6 stud hubs, with pitch circle up to 203mm• SP1500 Series Hydraulic Power Ram allows for smooth, progressive application of up to 8 tonnes of force• Fine pitch thread for easy adjustment• Floating plunger with free moving legs, enables quick and easy attachment to vehicle hubs• Can be used in 3, 4 or 5 leg combinations• Heavy duty force screw with impact handle included, where shock action is required to ‘break’ stubborn hubs• Supplied in steel storage case

• Specification:- Leg Reach: 158mm - Spread Capacity: 203mm - Stud Hole Diameter: 15.8mm - Puller Plate Thread: 1.1/2” BSW - Hydraulic Ram Thread: 1.1/2” BSW - Impact Screw Thread: 1.1/2” BSW

OFFER €270.95SAVE €58.00


PULL

ERS

4

Tel:

0154

3 67

9900

08600000

15520000

09810000

08542100

15000000

08540300

Two Leg Mechanical Thin Jaw Gear Puller• Thin jaws enable access where clearance behind components is limited• Two legs for removing gears, races, bearings and sprockets• Drop forged steel legs, beam and jaws• Heat treated for strength and durability• Min - Max Spread: 0 - 75mm• Max Reach: 75mm• Can be upgraded for triple leg pulling• Supplied in carton

Hydraulic Puller & Separator Kit• Makes 4 different twin/triple leg pullers, plus bearing separator kit• Puller Min - Max Spread: 50 - 150mm• Puller Max Reach: 150mm• External Min - Max Spread: 20 - 105mm• External Max Reach: 876mm• Supplied in lockable metal case

Multipull® Blind Housing Bearing Remover• Remove blind housing bearings without the need to dismantle machinery or remove the running shaft• Positive seating allows even tension on inner and outer bearing rings, reducing resistance• Stabilisers reduce sideways movement and self-centre the puller• Min Spread: 20mm • Max Spread: 117mm• Adaptor Dia: 5.5 - 12.5mm • Puller Reach: 415mm

Slide Hammer Assembly - 1kg• For use with Sykes-Pickavant split collet type internal extractors • Hammer displacement 220mm• Hammer weight 1kg

Hydraulic Ram - 8 tonnes force• SP1500 Series 8 tonnes Hydraulic Ram• Standard power unit for SP Hub Pullers and can also be used with many alternative SP puller applications e.g. 3 leg pullers, ball joint pullers, suspension bush removers etc

Slide Hammer Puller Kit - Combi Pull & Split Collets Extractor• 3 straight legs, 3 cranked reversible legs for internal

and external pulling• 4 split collet internal extractors• Adjustable cone ensures positive location, minimising

risk of slippage• Straight Leg - External Spread: 66 - 105mm - Internal Spread: 23 - 83mm - Maximum External Reach: 75mm• Cranked Leg - External Spread: 66 - 105mm - Internal Spread: 23 - 70mm - Maximum External Reach: 65mm• Split Collets - Internal Spread: 10.5 - 30mm

• Supplied in carton

OFFER €289.95SAVE €67.55


OFFER €489.95SAVE €102.00


OFFER €66.50SAVE €13.45

LIST PRICE €79.95

OFFER €89.95SAVE €12.00


OFFER €87.95SAVE €19.00


OFFER €399.95SAVE €84.00


Specifications

Part No.Internal Spread

Min - Max mm

List Price

Save Price

OfferPrice

09580900 6.5 - 8mm €40.95 €6.45 €34.50

09581000 8.5 - 10mm €40.95 €6.45 €34.50

09581100 10 - 12mm €41.50 €6.55 €34.95

09581200 12 - 17mm €47.95 €9.00 €38.95

09581300 19 - 22mm €55.50 €9.55 €45.95

09581400 22 - 30mm €77.50 €13.00 €64.50

09581500 30 - 38mm €93.95 €16.45 €77.50

09581600 38 - 50mm €145.95 €25.00 €120.95

09581700 50 - 60mm €173.95 €29.45 €144.50

1/2” female to M8 male converter:

09582000 n/a €18.00 €4.00 €14.00

Split Collet Internal ExtractorsThe split collet is pushed into the centre of the bearing and then expanded via the hex nut on the end of the collet until a secure grip is achieved. The slide hammer is then attached providing the necessary extracting force.

SUSP

ENSI

ON

5

ww

w.s

ykes

-pic

kava

nt.c

om08770000

08780000

08795000

08080000

08085000

084876V2

Universal Press Support BlockNow includes numbered support block allowing the user to easily log specific vehicle placements for future reference• Universal Support for use with a workshop press• Easily press bearings on a wide variety of suspension arms• Three point contact guarantees a perfect, safe support • Features: - Adjustable height anvil bolts - Swivel element for added versatility - Safety Alignment brackets for security on press

Universal Press & Pull Sleeve Kit - Car / LCV Kit• Universal applications - Car - LCV • Contains 20x Press Sleeves in 2mm diameter steps• Inside Diameter Range: 34 - 72mm• Outside Diameter Range: 44 - 82mm• 4x Step Plates / 4x Pulling Spindles with thrust bearings• Supplied in moulded storage case

Upgrade Kit - From 08790000 to 08797500• For owners of the Universal Press & Pull Sleeve Kit - 08790000 (SUV / LCV) who wish to upgrade to the full contents of the combined LCV / HGV Kit - 08797500

Universal Suspension Arm Lever• For lowering of the suspension arm and the separation of suspension components• Reduces the effort required, due to the unique design which uses leverage and the technicians’ own bodyweight to create the force required• Adjustable, multi-position swing point allows for variable applications – both LH & RH

Suspension Wear Indicator• An innovative tool for detecting suspension and axle joint wear• For detecting faults in: - Suspension Joints & Suspension Struts - Wheel bearings - Stabilizers, Bushes & Ball-Joints - Steering Gear & Links• The tool creates a rocking motion in any direction in order to detect movement in steering and suspension components• Uses weight of vehicle to highlight component wear under load conditions

Universal Protective Clamp for Strut Insert PistonsNow includes 70mm pins for increased applications• Fixes the piston rod in position when replacing coil springs• Prevents the piston rod from being drawn back into the strut

OFFER €308.50SAVE €77.45


OFFER €161.00SAVE €95.95


OFFER €488.95SAVE €214.00


OFFER €626.95SAVE €128.00


OFFER €84.50SAVE €18.00


OFFER €54.95SAVE €39.00

LIST PRICE €93.95

Scan the QR code to watch a video of

the Universal Press Support Block

Scan the QR code to watch a video of the UniversalSuspension Arm

Lever


video of the Suspension Wear

Indicator

UPDATED KIT

Scan the QR code to watch an overview video of

Suspension Removal & Installation Tools

CV Joint Puller• Specialist tool for the removal of CV joints on front wheel drive cars• No need to use a hammer – reduces risk of damage to the drive axle• Avoids the need to remove the entire front axle• Approved as a special tool by VW Group - Audi, Seat, Skoda. VW – Ref: T20181

Concentric Speedy Steering Rack Wrench• For removal and installation of steering rack knuckles - 35 to 45mm diameter• Works on all steering racks with track rods up to 30mm diameter• Self locking rollers adjust automatically to the required knuckle diameter, to provide a safe and secure grip• Manufactured to OEM specifications, as required by Mercedes, PSA, Renault, Toyota and VW Group• High Quality Grade Steels: - Forged Steel body - Heat treated steel rollers - Steel tube with 30mm diameter hex• Roller cage is replaceable should the rollers become worn or damaged

SUSP

ENSI

ON

6

Tel:

0154

3 67

9900

Suspension Wear Indicator• An innovative tool for detecting suspension and axle joint wear• For detecting faults in: - Suspension Joints & Suspension Struts - Wheel bearings - Stabilizers, Bushes & Ball-Joints - Steering Gear & Links• The tool creates a rocking motion in any direction in order to detect movement in steering and suspension components• Uses weight of vehicle to highlight component wear under load conditions

08680000

080500V2

08090000

08390000

08060000

08450000

OFFER €127.95SAVE €33.00


OFFER €77.50SAVE €17.00

LIST PRICE €94.50

OFFER €54.95SAVE €35.55

LIST PRICE €90.50

OFFER €638.50SAVE €129.00


4 Way Ball Joint Separator - Car / LCV applications• Unique 4-way lever design allows for a wide variety of applications• 4 options are available, by removing the pin and selecting any of the 4 positions• Tapered, slim jaw fork design with tough, black epoxy coating• Specification: - Jaw Opening: 24 / 30 / 40 / 45mm options - Jaw Throat Width: 19mm - Jaw Throat Depth: 30mm

Heavy Duty Coil Spring CompressorUnique Sykes-Pickavant design of vice-mounted Coil Spring Compressor• Features double-ended hex drive (2 x 24mm hex) for ease of use - Can be operated from either end using ratchet or 24mm wrench - Can be safely unwound in the event of shear pin failure• Hex drives at both ends, incorporate shear-pins for safety - Features external thrust bearing for ease of service - Heat treated, Self-lubricating operating screw• Safe Working Load = 15000N• Supplied with two sets of universal jaws: - Medium Jaws: 110-150mm dia - Large Jaws: 140-195mm dia• 084000 Series jaws can also be used with 08390000 Coil Spring Compressor (Requires 08393200 Screws)

N.B. Not recommended for use with Air / Electric Impact Power Tools

Long Reach Ball Joint Splitter• Ideal for ease of access, without being restricted by wheel arches• Specification: - Length: 400mm - Jaw Throat Width: 18mm - Jaw Throat Depth: 70mm

Internal Coil Spring Compressor• Specially designed for vehicles with front or rear wishbone suspension• Designed to fit applications where the access hole in the lower wishbone is as small as 30mm diameter • Unique Torque Safety Key extends functionality and adds safety - 100Nm max torque - Allows for use with an impact wrench• Supplied with two pairs of specialist jaws from 90mm to 140mm diameter• Full applications list included in kit• Safe working load of 2500kg (25000N)• Fits a wide variety of vehicles with Wishbone Suspension, including: BMW / Citroën / Chrysler / Honda / Hyundai / Kia / Mazda / Mitsubishi / Peugeot / Renault / Seat / Skoda / Suzuki / Toyota / Volvo / VW

Scan the QR code to watch a video of the ConcentricSpeedy Steering

Rack Wrench

OFFER €475.95SAVE €129.00


OFFER €25.95SAVE €13.00

LIST PRICE €38.95

STAR BUY

CO

OLI

NG

7

ww

w.s

ykes

-pic

kava

nt.c

om

331595V2

3319500033194200

33194400

33156100

33150100

33157800

Universal Hose Clamp• Clamping Range: 8 - 70mm• 1/4” drive and thumb screw for adjustment

OFFER €38.50SAVE €13.00

LIST PRICE €51.50

OFFER €89.95SAVE €13.00



LIST PRICE €38.95

‘315’ Series Cooling System Test Kit• The ‘315’ series Cooling System Pressure Test programme from Sykes-Pickavant provides extensive coverage for both popular and less popular models and is constantly updated as new models are released. More than 20 specialist cooling system cap adaptors are available• All components of the ‘315’ range are fully compatible with older SP Cooling System Kits and can be used to upgrade previous generations of Cooling System Pressure Test Kits which are fitted with quick-release connectors• For older systems with a threaded connection, an adaptor is available (03186870)• Contents: - Hand Pump with Pressure Gauge and Quick-Release fitting - Hose Assembly c/w quick-release fitting - 16 x Threaded Cooling System Cap Adaptors - 3 x Bayonet Fitting Cooling System Cap Adaptors - 1 x Cap Adaptor wrench

Combustion Leakage Tester• Accurate and fast diagnosis of cylinder head gasket leaks• Quick connector for use with 315 / 316 / 317 Series Cap Adaptors• Suitable for use with both Petrol & Diesel engines• Supplied with both Standard & Sensitive Reaction Test Fluid (250ml)

Reaction Fluid - Standard• Replacement Bottle of reaction fluid for 33195000 Combustion Leakage Tester• Standard - 250ml bottle (White Cap)

Reaction Fluid - Sensitive• Replacement Bottle of reaction fluid for 33195000 Combustion Leakage Tester• Sensitive - 250ml bottle (Black Cap)

OFFER €299.95SAVE €68.00


NEW

€25.95

€89.95 €10.50

€10.50

Cap Adaptor - Mini Cooper S• Suitable for Mini Cooper S 2002 onwards

Hand Pressure Pump c/w Gauge• 0 - 2.5bar / 35psi pressure pump• Gauge Diameter: 60mm • Suitable for ‘317’ Series caps• ‘318’ Series caps can be used with convertor 03176870

Cap Adaptor - Dennis Dart / Optare Solo• Suitable for Dennis Dart PSV’s and Optare Solo PSV’s

03265000

Comprehensive applications listing provided with each kit

CO

MPR

ESSI

ON

& P

RES

SUR

E TE

STIN

G

8

Tel:

0154

3 67

9900

31470000

31440000

314875V2

314925V231462000

Oil Pressure Test Kit• Helps to diagnose worn oil pumps and engines, faulty oil pressure switches and pressure warning indicators• Shock protected dual scale gauge, for quick and accurate oil pressure checks• Permanently oil primed, long flexible hose, enables access to difficult to reach oil switch ports• Small profile, quick coupling adaptors with built-in shut-off valve for fast secure connection• Includes oil pressure test gauge c/w 1m oil primed hose and 10 x oil switch port adaptors

Catalyst Back Pressure / Vacuum Tester• Measures the back pressure (or vacuum) via the Lambda Sensor socket, to indicate blocked or damaged catalytic converters• Calibrated gauge scale indicates progressive pass / fail for tests at idle speed and for tests under load - coloured indication • 2m heat resistant pipe for dynamic testing• Suitable for M12 x 1.25 and M18 x 1.5 Lambda (Oxygen) Sensor sockets• Fits most European, Asian, Japanese vehicles• Includes pressure gauge, hose assembly, 2 x Lambda Sensor Socket Connectors, 2 x thread cleaners and a special adaptor for Toyota Vehicles• Supplied in plastic case with foam insert

Fuel Injection Pressure Test Kit for Petrol Engine VehiclesUpdated kit now covers Alfa Romo, Fiat, Lancia and new Ford Ka vehicles• Universal Injection Pressure Test Kit for modern Electronic, Multi-point injection systems• Shock protected, fuel resistant dual scale gauge – to 10bar / 145psi• Relief valve for safe depressurisation• Quick coupling adaptors and connectors• Wide applications range: - S type, 8mm plastic push-in fittings, as used on Alfa, Audi, Citroën, Fiat, Ford, GM, Peugeot, VW etc - Schrader type valve test port adaptors (7/16 & 8mm) as used on Alfa, BMW, Chrysler, Ferrari, Fiat, Ford, GM, Mercedes, Mini, Volvo etc - Specialist Renault fittings for use on Renault 1.2 / 1.4 / 1.6 Petrol Engines - Clio, Twingo, Kangoo, Extra, Megane, Scenic etc• Supplied in plastic case with foam insert Optional fittings available to suit older vehicles

VW Group Fuel Pump Pressure Test Kit for PD (Diesel) & FSi EnginesNow includes 90 degree elbow to overcome access issues on certain models• A specially designed Fuel Pressure Tester for the PD & FSi ranges of engines as used by VW Group• 20bar Pressure Gauge – as both PD and FSi fuel pumps operate at higher pressures than normal fuel pumps• Extra long hose assembly for ease of access – 600mm• Includes special PD fuel pump quick connector (Diesel) and 2 x special FSi fuel pump connectors for 1.6, 1.8, 2.0 FSi engines with Bosch fuel pumps

Common Rail Diesel (CRD) Fuel Return Flow Kit• Designed for use on the injector return side of a CRD system• Helps to diagnose: - Poor or no engine starting - Poor engine running - Poor acceleration - General lack of engine power• Compact acrylic block design provides easy to read cylinder comparison (much easier to compare than with plastic bottles, due to compact design and graduation scale)• Fuel resistant, highly flexible rubber hoses• Suitable for solenoid injectors only• Contents: (Supplied in plastic case) - Graduated acrylic measuring block for up to 6 cylinders - Injector adaptor sets for: Bosch / Delphi / Denso / Siemens - Set of reduction pipes for small diameter flow back ports - Under bonnet hanging hook

OFFER €219.00SAVE €13.00


OFFER €212.95SAVE €13.00


OFFER €367.95SAVE €32.00


OFFER €212.95SAVE €44.00


OFFER €166.50SAVE €26.00


UPDATED KIT

UPDATED KIT

TIM

ING

TO

OLS

9

ww

w.s

ykes

-pic

kava

nt.c

om07763500

07755500

07757100

07756005

07740000

07744400

Opel / Vauxhall 1.0 / 1.2 / 1.4 Petrol Engine Timing Kit• Applications: Opel / Vauxhall Adam (‘12-) Opel / Vauxhall Ampera (‘11-) Opel / Vauxhall Astra J (‘09-) Opel / Vauxhall Corsa D (‘09-) Opel / Vauxhall Insignia (‘11-) Opel / Vauxhall Meriva-B (‘10-) Opel / Vauxhall Mokka (‘10-) Opel / Vauxhall Zafira C (‘11-)

• Engine Codes: 1.0 - A10XEP 1.2 16V - A12XEL (LWD), A12XER 1.4 16v - A14NEL (LUJ), A14NET (LUJ), A14XEL (LDD), A14XER (LDD)

Nissan 2.0DCI, Opel / Vauxhall 2.0 / 2.3D CDTI & Renault 2.0DCI / 2.3DCI Diesel Engine Timing Kit• Applications: Nissan Primastar (‘08-), Qashqai (‘07-), X-Trail (T31) (‘07-), Opel / Vauxhall Movano B (‘10-), Vivaro (‘06-), Renault Espace 1V (‘06-), Koleos (‘08-), Laguna 2 (‘05-’07), Laguna 3 (‘07-), Megane II (‘06-), Megane III (‘09-), Master III (‘10-), Scenic II (‘06-), Scenic III (‘09-), Traffic II (‘06-), Vel Satis (‘05-)

VW Group 1.2 - 2.0 Common Rail Diesel Engine Timing Kit • Designed to fit the newest common rail diesel engines which are significantly different from the older PD engines. These CR engines combine belt and gear drives by using a toothed belt to transfer the drive from the crankshaft to one of the cam shafts then using gears to transfer the drive from one cam to the other• Applications: Audi A1 (‘10-), A3 / A6 / Q5 / TT (‘08-), A4 (‘07-), A5 (‘09-), Q3 (‘11-), Seat Alhambra (‘10-), Altea (‘09-) Exeo (‘09-), Ibiza (‘10-), Leon (‘09-), Toledo (‘09-), Skoda Fabia 2 (‘10-), Octavia (‘09-), Rapid (‘12-), Roomster (‘10-), Superb (‘08-), Yeti (‘09-), Volkswagen Amarok (‘10-), Caddy Maxi (‘10-), Crafter (‘11-), Eos (‘08-), Golf VI (‘09-), Golf Plus (‘09-), Jetta (‘09-), Passat (‘08-), Passat CC (‘08-), Polo V (‘09-), Scirocco (‘08-), Sharan (‘10-), Tiguan (‘07-), Touran (‘10-), Transporter T5 (‘09-)

VW Group Multi-Position Tensioner Wrench• Five adjustable positions for ease of access• Retains the tensioner to allow for tightening of the tensioner nut• Suitable for both petrol and diesel applications• Requires a 4mm Hex Key to adjust the positioning • OEM Reference: T10020 / V159

Flexible Auxiliary Drive Belt Fitting Tool • Designed to assist in the fitting of new style alternator / air-con / power steering drivebelts, which have no load adjustment mechanism and are designed to be “stretched” into place• Guides the belt into the correct position, whilst turning the crankshaft pulley by hand• Steel guide pins help lock the tool in-situ, whilst the alloy body guides the belt over the edge of the pulley, and supports the load on the belt during the fitting process

Stretch Belt Fitting Tool - Dual Size Pulleys• Specially designed two-piece tool for installing and dismounting stretch belts on double pulleys where the two pulleys are of different diameters• Allows the belt to be installed in one operation• Ideal tool for Ford Focus applications with double pulley

OFFER €290.50SAVE €58.00


OFFER €123.50SAVE €25.00


OFFER €270.95SAVE €57.00



LIST PRICE €45.00


LIST PRICE €48.95

OFFER €128.95SAVE €26.00


NEW

NEW

NEW

07763400VW Group 1.2TSI / 1.4T, FSI, GTI and 1.6FSI Petrol Engine Timing Kit • Set of locking tools required for chain maintenance• Applications: Audi A1 (‘10-), A3 (‘04-), Seat Alambra (‘10-), Altea (‘10-), Cordoba (‘06-), Ibiza (‘06-), Leon (‘07-), Toledo (‘12-), Skoda Fabia 2 (‘07-), Octavia 2 (‘08-), Rapid (‘12-), Roomster (‘06-), Superb II (‘08-), Yeti (‘09-), Volkswagen New Beetle (‘11-), Caddy Maxi (‘10-), Eos (‘06-), Golf IV (‘06-), Golf V (‘03-), Golf VI/Plus (‘09-), Jetta (‘06-), Passat (‘05-), Polo IV (‘02-), Polo V (‘09-), Scirocco (‘08-), Sharan (‘10-), Tiguan (‘07-), Touran (‘06-)

NEW

TIM

ING

TO

OLS

10

Tel:

0154

3 67

9900

Nissan 2.0DCI, Opel / Vauxhall 2.0 / 2.3D CDTI & Renault 2.0DCI / 2.3DCI Diesel Engine Timing Kit• Applications: Nissan Primastar (‘08-), Qashqai (‘07-), X-Trail (T31) (‘07-), Opel / Vauxhall Movano B (‘10-), Vivaro (‘06-), Renault Espace 1V (‘06-), Koleos (‘08-), Laguna 2 (‘05-’07), Laguna 3 (‘07-), Megane II (‘06-), Megane III (‘09-), Master III (‘10-), Scenic II (‘06-), Scenic III (‘09-), Traffic II (‘06-), Vel Satis (‘05-)

Flexible Auxiliary Drive Belt Fitting Tool • Designed to assist in the fitting of new style alternator / air-con / power steering drivebelts, which have no load adjustment mechanism and are designed to be “stretched” into place• Guides the belt into the correct position, whilst turning the crankshaft pulley by hand• Steel guide pins help lock the tool in-situ, whilst the alloy body guides the belt over the edge of the pulley, and supports the load on the belt during the fitting process

Alfa Romeo 1.4 T-JET & Fiat 1.2 / 1.4 16V Petrol Engine Timing Kit• Set of locking tools required for cam belt service and engine maintenance• Applications: Alfa Romeo Giulietta (‘10-), Mito (‘08-), Fiat 500 / C / Grand Punto / Linea (‘07-), Brava / Bravo (‘98-), Doblo (‘10-), Idea (‘04-), Marea (‘98-’00)

07763300

07763200

07764400

07751900

Alfa Romeo 1.4 Multiair (105 - 135 - 170 hp) Engine & Fiat 1.4 Petrol Engine Timing Kit• Set of locking tools required for cam belt service & replacement• Applications: Alfa Romeo Giulietta (‘10-), Mito (‘08-), Fiat Bravo (‘07), Punto (‘12-), Punto Evo (‘09-)

Ford Mondeo 1.8 & Mazda 2.0DISI / 2.3MPS Petrol Engine Timing Kit• Set of locking tools required for correct valve timing on chain driven engines• Applications: Ford Mondeo 1.8 (‘03-’07), Mazda 3 (‘06-), 5 (‘05-), 6 (‘10-), CX-7 (‘07-)

Fiat 1.2 / 1.4 8V & Ford 1.2 Petrol Engine Timing Kit• Set of locking tools required for cam belt service• Applications: Fiat 500 / C / Linea (‘07-), Doblo (‘05-’10), Florino (‘09-), Idea / Grand Punto (‘05), Punto Evo / Panda / Qubo (‘09-), Ford Ka (‘09-)

OFFER €106.95SAVE €22.00


OFFER €42.50SAVE €22.00

LIST PRICE €64.50

NEW

NEW

NEW

NEW

OFFER €176.95SAVE €36.00


OFFER €213.95SAVE €44.00


OFFER €186.95SAVE €39.00


07767100Crankshaft Pulley Holding Tool• Commonly used on 1.4 & 1.6 16v Audi, Skoda and VW engines• OEM Reference: 3415

OFFER €107.00SAVE €21.95


CO

MM

ERC

IAL

VEH

ICLE

S

11

ww

w.s

ykes

-pic

kava

nt.c

om

18070000

08070000

08254500

80050000

0825350008254000

80055000

21205000

Hydraulic Ball Joint Separator – HGV applications• Hydraulic version of the 08070000 HGV Ball Joint Separator (above)• Uses hydraulic power from the SP 1500 series Hydraulic Ram• Provides up to 8 tonnes of hydraulic pressure• Jaw Opening: 70mm Jaw Throat Width: 36mm Jaw Throat Depth: 50mm

Ball Joint Separator – HGV applications• Strong, heavy duty body, with strengthened fork and lever, allows for greater force to be applied• Can be upgraded to hydraulic power • Jaw Opening: 70mm Jaw Throat Width: 36mm Jaw Throat Depth: 50mm

Ford Transit Hub & Front Wheel Bearing Remover Kit• For Ford Transit Mk6 & Mk7 Hub and complete front wheel bearing removal• Features a heavy duty slide hammer which operates in two directions to achieve multiple operations in one tool• Provides three different solutions in one kit: - Can be used as a traditional hub puller - Remove the stubborn inner bearing race - Use the slide hammer in the reverse direction to remove the outer bearing race

‘Motorq 500’ - 3/4” Push-Thru Heavy Duty Torque Wrench • 3/4” push-thru sq dr • 300 - 1000 Nm / 200 - 750lbs.ft • Length: 1475mm • Weight: 7.30kg

Ford Transit Brake Disc Remover• Removes the front brake discs (without damaging the bearings) on FWD and RWD Ford Transits from 2001 onwards• Manufactured from Chrome Molybdenum for strength• Removes front brake discs without damaging the bearings• Can be used on FWD & RWDN.B. Equivalent to Ford OEM Tool ref 204-345B

Ford Transit Rear Hub Puller• Designed for removal of the Rear Hub on FWD Ford Transits• The bearings on these Transits often seize in place, requiring this special tool for removal of the hub• Application: Ford Transit 2000 onwards (FWD models only)• Includes safety chain to prevent hub assembly from accidentally falling on operators foot / legN.B. Equivalent to Ford OEM tool ref 204-595-09

‘Motorq 550’ - Stepped 3/4” to 1” Heavy Duty Torque Wrench • 1” Sq. Dr (uses ¾” to 1” stepped convertor) • 700 - 1500 Nm / 500 - 1000lbs.ft • Length: 1475mm • Weight: 10.40kg

20 Tonne Loadstar “Plus” Press Frame - Complete Kit (Special version for “Optare” Buses)• 20T Hydraulic Cylinder and Pump• Stand alone portable press frame kit for pin pushing applications• Useful for removal of HGV suspension King Pins• Includes 5 extractor (pushing) pins for those hard to reach applications• Includes 1 extractor (pushing) pin for Optare applications• Auto-Grip collar and adaptor for quick change of pins

OFFER €277.50SAVE €56.50


OFFER €464.50SAVE €54.00


OFFER €735.50SAVE €42.45


OFFER €2573.50SAVE €387.00


OFFER €106.95SAVE €22.00


OFFER €308.50SAVE €62.00


OFFER €149.00SAVE €31.50


Videos available on our website for all operations - visit www.sykes-pickavant.com€425.95

Scan the QR code to watch an overview video of the Ford Transit Hub & Front

Wheel Bearing Remover Kit

3 IN 1 TOOL

WO

RKS

HO

P EQ

UIP

MEN

T

12

Tel:

0154

3 67

9900

50175000

36600500

MV5600

53390000

7 x Sliding Drawer Cabinet• Lockable top compartment and drawers (Top compartment can be locked independently to drawers)• Lid opens using twin gas filled struts • Large transport handle• 7 x fully opening drawers • Anti-slip rubber covering on lid• Lockable swivel casters • Rigid corner protection• 160mm deep top compartment with 85 litre storage• High quality steel casters with protective rubber coating (2 x fixed & 2 x swivel)• Drawers run on low friction telescopic ball bearing slides• Tool storage compartments on both sides ideal for hanging screwdrivers etc• Dimensions: Width: 1030m - Depth: 500mm - Height: 800mm

€51.50

€767.50

€346.95

€540.50

NEW

A NEW range of Hydraulic Workshop Presses equipped with a two-speed manual pump, overload safety valve, automatic arm back-run system and V blocks

Part No. RatingHeight(mm)

Width(mm)

Depth(mm)

Bed Depth(mm)

Range(mm)

Weight (kg)

Price

53436100* 10T 1840 850 500 145 80 - 1000 135 €677.50

53436000* 15T 1930 920 650 170 85 - 950 150 €702.95

53436200* 20T 2030 940 650 180 65 - 1030 165 €857.95

53436300* 25T 2030 950 650 180 70 - 1030 170 €1115.95

53436400* 30T 2060 1120 650 200 115 - 1020 230 €1270.95

53436500 50T 2290 1220 650 210 70 - 1065 370 €1992.95

• Welded, heavy duty steel frame • Two speed pump• Overload safety valve • Automatic arm return• Pressure gauge • V blocks• Winch for table (For models 53436400 & 53436500) • Manufactured in the EU• Piston over-travel limit stop

*Recommended for use with Universal Press Support Block - 08770000 - See page 5 for further details

Pneumatic Oil Extractor• Remove and extract waste fluids or oil from an engine with flexible PV tube and robust probe• Powered from compressed air• 70L tank capacity• Adjustable 10L oil capture pan• Visible fill level indicator• 1 - 2 L/Min Suction capacity depending on nozzle used• Working pressure 8-10 Bar• Emptying with compressed air 1-2 bar• CE Approved• Includes selection of PV tubes to cater for different lengths and diameters of dipstick tubesWARNING: Do not use with corrosive or inflammable products

Fuel Extractor / Retriever• Retrieve fuel following a filling error, removal of tank sender unit, changing or checking the fuel gauge, rinsing the fuel tank during body work etc• Operates from workshop compressed air (no risk of sparks)• Mobile 45-litre tank (on wheels)• Cleanly draws up or pushes out fuel due to a venturi system• Includes 2 anti-static ground cables, overflow line and 3 fuel probes• Emptying via the tank filler neck or fuel lines• Stainless steel

Fuel Retriever Fuel Line Adaptor Set• Allows the Fuel Retriever (36600500 - above) to be connected in- line for extracting fuel from fuel lines and pumps• Connects just before the injection pump (on most fuel lines or filters) for completely safe removal of fuel

€321.00

SUSP

ENSI

ON

13

ww

w.s

ykes

-pic

kava

nt.c

om187000V2

1874030018747100

18747200

90206000

18780300

Universal Press Frame c/w 12 tonne Hydraulic Ram• Updated unit now provides greater power• Allows easier operation - 50% more capable using the SP 12 tonne Hydraulic Ram• Includes adaptor ring for use with 08780000 Universal Press & Pull Sleeve Kit • Can be used in the following formats: - On its own as a stand alone tool - With Universal Press & Pull sleeve kits• Open frame design - 200mm of clearance through the press frame• Ideal for use with individual model specific press piece sets

Press Piece Set - Mercedes Sprinter• Mercedes Sprinter (‘96 onwards)• VW LT / Crafter

Mercedes Suspension Arm Adaptor Set• For use on Inner Torsion Bar Ball Joints - Mercedes W211 (E Class ‘02 - ‘09) - Mercedes W220 (S Class ‘98 - ‘06)This set can be used in conjunction with either 18780200 - Universal C Clamp or with 18780300 Ball Joint C-Clamp when working off-the-vehicle – However, for on the vehicle usage, the Ball Joint C-Clamp 18780300 has been designed for this purpose.

Mercedes Ball Joint Adaptor Set• For use on Outer Ball Joints - Mercedes W211 (E Class ‘02 - ‘09) - Mercedes W220 (S Class ‘98 - ‘06) - Mercedes W230 (SL Class ‘02 - ‘09)This set can be used in conjunction with either 18780200 - Universal C Clamp or with 18780300 Ball Joint C-Clamp when working off-the-vehicle – However, for on the vehicle usage, the Ball Joint C-Clamp 18780300 has been designed for this purpose.

‘Vibro-Impact’ Air Hammer• A unique concept to aid the removal of seized suspension parts• The ‘Vibro-Impact’ system allows for the controlled application of force via an air powered Impact Hammer• Allows the operator to control and gradually increase the force being applied, in order to loosen seized components• Features a built-in shock-absorber in order to minimise risk of damage if too much pressure is accidentally applied• Low vibration for user comfort• Supplied with a handy wall mounted storage bracket and a set of four impact hammers for variable applications

Universal C Clamp• For the dismantling and installation of suspension parts on the vehicle• Specially designed for use with the ‘0878’ / ‘0879’ Series Press & Pull Sleeve Kits• Designed to allow greater access in restricted situations and where the universal press frame is not suitable• Special ‘trapezoidal’ threaded screw, allows for the application of greater force and can be used with Impact Air Wrenches, as well as standard ratchets / wrenches etc• Also capable of accepting the SP1500 or SP1800 Hydraulic Rams• Internal Frame dimensions: 170mm x 60mm• Use with specific Ball Joint piece sets for individual applications• Ideal for Mercedes applications - Ref: 18747100 / 18747200 - see above

OFFER €315.95SAVE €70.00


OFFER €263.00SAVE €53.00


OFFER €386.95SAVE €93.00


OFFER €123.00SAVE €25.50


OFFER €359.95SAVE €72.00


OFFER €175.50SAVE €37.45



video of the ‘Vibro-Impact’

Air Hammer

187502V2Press Piece Set - Opel Movano / Renault Master / VW T4• Opel Movano / Renault Master and VW T4 Ball Joint Removal & Installation

SUSP

ENSI

ON

BU

SH T

OO

LS

14

Tel:

0154

3 67

9900

08730400

08760100

0876020008730200

08760300

Ford Mondeo Rear Bush Tool• Individual press piece set for dismantling and installing the rear wishbone / trailing arm bush• Suitable for: - Ford: Mondeo 2007-, Mondeo Estate 2000 - 2007, S-Max & Galaxy 2006- - Volvo: XC70 & V70 2007-, XC60 2008-, S60 & V60 2010-

VW / Audi Rear Axle Bush Insertion Tool• For installation of bonded rubber / plastic type rear axle mounting bushes, on Audi A3, VW Golf 4, VW Bora - all models 2001 - 2004N.B. Most models were originally fitted with hydraulic type rubber bushes when new - These can be knocked out manually. This tool is required for fitting the new bonded rubber / plastic type replacement bushes. Always replace in pairs.

VW Polo Front Control Arm Bush Tool• For removal and installation of the rear bush on the front control arm, as fitted on: - VW Polo IV - 2001- - Seat Cordoba III - 2002- - Skoda Fabia - 1999-

Ford Focus Rear Wishbone Bush Tool• For removal and installation of rear wishbone / trailing arm bush on all Ford Focus models 1998-

VW Group Control / Trailing Arm Bush Tool• Heavy Duty mechanical kit for replacing and removing control / trailing arm bushes • Suitable for: - VW Golf V, VI 2003- - VW Golf Plus 2005- - VW Eos 2006- - VW Touran 2003- - VW Jetta III, IV 2005- - VW Scirocco 2008-- VW Passat 2005- - VW Tiguan 2007- - VW Sharan 2010- - Audi A3 2003- - Audi TT 2006- - Seat Altea / Leon 2004- - Seat Toledo 2004 - 2009 - Seat Alhambra 2010- - Skoda Octavia 2004- - Skoda Superb 2008- - Skoda Yeti 2009-

08720600

08041000

08750100

Mini Control Arm Bush Tool• For removal and installation of front control arm rear bushes• Front control arm bush tool for BMW Mini -07• For Mini Cooper R50 / R53 (W10 / W17 / W11)• Left & Right arm bush replacement on the vehicle

VW Alloy 4 Link Suspension Bolt Remover Set• Simple tool to use with ‘vibro-impact’ air hammer (90206000 - see page 13) when bolt ends protrude from housing• Sleeve guides the impact end to free off and push bolt through the housing• Extension adaptor for removing bolts when pushed deep in the housing

Renault Laguna Rear Suspension Bush Tool• For removal and installation of rear axle bushes on Renault Laguna 2 2001-

OFFER €192.95SAVE €43.00


OFFER €256.95SAVE €53.00


OFFER €483.95SAVE €25.55


OFFER €136.95SAVE €28.00


OFFER €163.95SAVE €33.55


OFFER €219.50SAVE €45.00


NEW LOWER PRICE

ON CARSOLUTION

€308.50

€49.95

BEA

RIN

G R

EMO

VAL

/ IN

STA

LLAT

ION

15

ww

w.s

ykes

-pic

kava

nt.c

om

Ford 82mm BearingVW Group Bearing

• The GEN 2 type of wheel bearing is predominantly fitted to models from Ford, Land Rover, Mazda, VW Group and Volvo

• Includes a variety of different diameter tool kits covering a range of sizes to suit the different GEN2 bearings used by vehicle manufacturers

• Designed to distribute pressing force evenly through the outer bearing race and also allows for the suspension leg to remain in-situ on the vehicle when fitting new bearings

GEN2 Bearing Removal Combination Tool Kit for VAG Group 62 / 66 / 72 / 85mm• Combination Kit for Audi / Seat / Skoda / VW applications• Consists of all necessary parts from the 62, 66, 72 & 85mm kits - 62mm Kit - Audi A2, VW Lupo (Front) - 66mm Kit - Skoda Fabia, VW Fox (Front), Polo - 72mm Kit - Audi A1, Audi A2, Seat Cordoba, Ibiza, Skoda Fabia, Roomster, VW Polo (Front), VW Fox with PAS (Front) - 85mm Kit - VW Multivan, Touareg, Transporter (Front / Rear)

GEN2 Bearing Removal Combination Tool Kit - 62 / 66 / 72 / 78 / 82 / 85mm• Combination Kit for Audi / Seat / Skoda / VW applications• Consists of all necessary parts from the 62, 66, 72 & 85mm kits - 62mm Kit - Audi A2, VW Lupo (Front) - 66mm Kit - Skoda Fabia, VW Fox (Front), Polo - 72mm Kit - Audi A1, Audi A2, Seat Cordoba, Ibiza, Skoda Fabia, Roomster, VW Polo (Front), VW Fox with PAS (Front) - 78mm Kit - Ford Focus II, C-Max, Volvo C30, C70, S40, V50 (Front), Mazda 3 - 82mm Kit - Ford Mondeo, Galaxy, S-Max, Land Rover Freelander 2, Volvo S80, V70, XC60, XC70 - 85mm Kit - VW Multivan, Touareg, Transporter (Front / Rear)

Universal Wheel Bearing Kit• Universal set for the removal and installation of flanges and wheel bearings, without the need for removal of suspension struts or wheel hubs from the vehicle (where access permits) • Remove and install wheel bearing without hub removal - Virtually eliminates damage to vehicle components - Removes the need to remove stubborn hub pinch bolt found on modern VW Group vehicles such as Audi A4, VW Passats etc• Tool configures square to bearing – No more having to square hub assembly on hydraulic press • Bearings fitted on nut assemblies – Greatly reduced drag in pushing bearing in / out• Flange extraction bolts supplied - Reduces time taken to complete overall job• Supplied in storage case – all components available individually as spare parts

GEN2 Bearing Removal Combination Tool Kit 78 & 82mm• Combination Kit for Ford / Volvo / Land Rover / Mazda applications• Consists of all necessary parts from the 78 & 82mm kits - 78mm Kit - Ford Focus II, C-Max, Volvo C30, C70, S40, V50 (Front), Mazda 3 - 82mm Kit - Ford Mondeo, Galaxy, S-Max, Land Rover Freelander 2, Volvo S80, V70, XC60, XC70

08128000

08129000

081220V2

08120000

OFFER €935.50SAVE €90.00


OFFER €317.50SAVE €68.00


€548.50

€1567.50

AIR

TO

OLS

16

Tel:

0154

3 67

9900

90210000

53399000 53399500

90201100

OFFER €269.95SAVE €80.00


High quality air tools that set the standard for Torque!

• Impact wrench with a smart design and ergonomically designed handle• Single-switch can be changed for easy forward or reverse operation• Easily adjustable torque regulator• Can be configured for right and left handed use• Composite body

90201500

Impact Wrench Specifications:

Part No. DriveMax Torque

Nm(Reverse)

Torque Nm

(Fwd)

Noise(dBA)

AirConsumption

(l / min)

Weight(kg) Price

90201000 1/2” 1600 1084 94.2 135 1.8 €229.95

90201500 (Mini)

1/2” 680 500 93.5 130 1.08 €217.95

90202000 3/4” 2600 2000 97 210 3.2 €643.95

90202500 3/8” 680 500 93.5 130 1.08 €217.95

90203500 1/4” 90 90 98.2 105 0.9 €179.50

90204500 1” 3100 2200 110 305 6.8 €1095.50

90204500

Signal Hose - 10mm (3/8”)• Length: 10 metres• High-visibilty hose to reduce trip hazard• Abrasion resistant outer cover• Working temp range -40°c to +65°c• Working pressure 300psi• Break pressure 1000psi• N.B. Hose supplied without fittings

Retractable Hose Reel - 20m x 10mm• Spring driven retractable hose reel c/w wall mounting brackets• Heavy duty UV stabilised polypropylene• Suitable for compressed air or cold water up to 20 bar working pressure • Includes 20 metre x 10mm heavy duty black rubber air / water hose to ISO EN 2398 standard • 3/8” bsp female inlet and the hose terminates in a 3/8” bspt male

Hoses also available in 20m x 8mm (3/8” fittings) and 18m x 12mm (1/2” fittings). Contact Customer Services for more information

Retractable Hose Reel - 10m x 10mm• Spring driven retractable hose reel c/w wall mounting brackets• UV stabilised polypropylene • Suitable for compressed air or cold water up to 20 bar working pressure• Includes 10 metre x 10mm heavy duty black rubber air / water hose to ISO EN 2398 standard• 3/8” bspt male inlet and the hose terminates in a 3/8” bspt male

Hoses also available in 12m x 6mm (1/4” fittings) and 12m x 8mm (3/8” fittings). Contact Customer Services for more information

Rubber Boot - For 90201000• For use with 90201000 1/2” Impact Wrench (above)• Protects gun from accidental damage*Impact wrench not included

NEW NEW

€38.95

€21.95

OFFER €169.95SAVE €16.00


WO

RKS

HO

P TO

OLS

17

ww

w.s

ykes

-pic

kava

nt.c

om90803000

90803500

960200SP

96015000 96026000

90803100

1/2” 18.0v Cordless Impact Wrench c/w 1 x batteryUltra high torque 1/2” 18.0v Cordless Impact wrench c/w 1 x battery• Smart design and ergonomically designed handle• Easily controlled forward / reverse switch • Variable speed trigger• Breakaway Torque: 982Nm

• Specification: - Weight: 3.08kg - Length: 240mm - Height: 265mm - Breakaway Torque: 982Nm - Battery: 18v 3.0Ah - Charging time: 45 minutes

- EU Version: 90803200

NEW

Max Torque982Nm

€643.95

€193.50

€128.95

€36.95 €74.95

1/2” Cordless Impact Wrench c/w 2 x 18.0v batteries• As per 90803000 (left) but includes 2 x 18.0v batteries

- EU Version: 90803300

Replacement Battery for 1/2” Cordless Impact Wrench • 18.0v Lithium Ion Battery €837.50

INCLUDES SP INDUCTION HEATER + & COIL KIT FOR

€831.95 (960200SP - UK 960201SP - EU)

Contains 8 x popular sizes of interchangeable coils

96015000

SP Induction Heater + with Coil Kit (96015000)The SP Induction Heater + is a redesign and upgrade of the popular Mini-Ductor II® and uses new engineering technology for increased energy efficiency and ease of use. Now you can use the power of technology with a flameless heat to quickly release corroded or seized components and other metallic parts. All without the damage normally associated with gas torches. Heats in seconds!Key features of the SP Induction Heater +• Specifically designed for the UK/EU: 230v/6 amp/1000 watt – with full CE certification• Operates cooler for better efficiency, handling and product longevity • Long operating cycle time • Carry Case; with storage for all attachments, fits in tool chests for security • LED work light illuminates work area• Integrated CE filter improves handling of product • 1 year warranty - Parts/Labour• A true 1,000 watts max output power available • Kit includes rope, u-form and pre-formed coil

SP Coil Kit• Contains 8 x popular sizes of interchangeable coils

SP Rope Coil• Highly adaptable coil allows user to shape to suit• Use three / four windings of coil for maximum performance

OFFER €831.95SAVE €64.55


96025000SP Heat Pad• Removal of decals, graphics, stripes, emblems and body mouldings etc• Softens the adhesive to make removal simple & effective

WO

RKS

HO

P EQ

UIP

MEN

T

18

Tel:

0154

3 67

9900

385800SP

386800SP

Pneumatic Coil Spring Compressor Workstation - Extra Heavy Duty Model c/w FREE Mercedes Bracket SetUniversal piece of equipment for assembling and disassembling struts and coil springs• Suitable for cars, 4WD’s and light commercials that use McPherson strut type suspension systems• Front and side spring clamps designed for fast changeover using unique Brackets System• Fitted with Extra Heavy Duty Pneumatic Cylinder - Compression force (at 10 bar) = 2452 kg • Ideal for Extra Heavy Duty applications i.e. SUV’s, 4WD’s etc where full spring compression is required• Double-depth front plate for use on extra-long strut assemblies• Safety locking valves system – locks safety cage and prevents usage with cage open

Mechanical Coil Spring Compressor Workstation c/w FREE Mercedes C Class BracketUniversal piece of equipment for assembling & disassembling struts and coil springs• Standard workstation construction but with Heavy Duty Mechanical compression components in place of pneumatic parts• Allows for use where air supply is limited, restricted or unavailable i.e. Mobile use• High power mechanical spindle allows for the application of up to 1600kg of compression force onto contained spring• Long main spindle achieves large 420mm of stroke – even greater than our pneumatic workstations• Powered by easy access 19mm hex drive on top of tool direct onto main spindle and can be used with either hand tools or even impact air tools• Includes adjustable vice clamp as standard• Compatible with all other Sykes-Pickavant workstation standard jaws, brackets & accessories• Dimensions: 1400 x 520 x 300mm

SCAN THE QR CODE TO WATCH A VIDEO OF THE

SUSPENSION WORKSTATION RANGE

€1025.50

€2057.50

38480100

38480500 38480600 38480700

38480200 38480400Mercedes BracketSet - A, B, C & E Class

Special BracketPorsche Cayenne / VW Touareg

Special BracketMercedes C Class(2010-)

Special BracketNissan Qashqai

Double DepthStrut Vice

Upper Jaw Setfor High Compression Springs

€303.50 €127.95€51.50

€229.50 €122.50 €148.50

Optional Accessories for use with Suspension Workstations

UP TO 1600KG OF FORCE

MERCEDES BRACKET SET (38480100) UPPER BRACKET FOR MERCEDES A, B, C, E CLASS

& LOWER BRACKET FOR MERCEDES E CLASS WORTH €303.50

FREE

WHEN YOU PURCHASE 385800SP

MERCEDES BRACKET (38480500) SPECIAL BRACKET FOR MERCEDES C CLASS 2010-

WORTH €229.50

FREE

WHEN YOU PURCHASE 386800SP

UP TO 2452KG OF FORCE (AT 10 BAR)

TEST

ING

19

ww

w.s

ykes

-pic

kava

nt.c

om Portable 4 Gas Analyser with PrinterDeveloped from the 32420000 gas analyser• For fault diagnosis, tuning and pre-MOT testing• Truly portable hand-held gas analyser• Ultra light weight - only 1.1kg• Measures CO, HC, CO2, O2 (NOx model option available on request) to Class 1 accuracy• Suitable for both petrol and LPG vehicles• Ideal for both static and dynamic testing• Provides Lambda / AFR measurement and corrected CO• Internal memory stores up to 250 test results - manual & automatic recording options• Pump speed control - Improves battery life • Up to 4 hours internal battery life• Bluetooth connectivity to PC (additional software required) • Large graphic display • Free analytical software available to download • Includes printer• Includes AC & 12v chargers

33540000

30050000

PP319FTCBrake Fluid Tester• A quick and clear condition tester for brake fluid• Shows water content in a series of LED indicators• Quick change selection for DOT3, 4 or 5.1 fluid testing

Automotive Digital Multimeter• Full control manual range selection • AC/DC Voltage measurement up to 600 Volt • DC Current measurement up to 10 A• Resistance measurement up to 2 MOhm • Diode & Continuity Tests • Overload protection & Auto Power-off • Low battery indicator • Soft holster for instrument protection• Dwell measurement from 0 to 120° • Temperature measurement from -40°C to 1000°C• Tachometer function measures from 500 to 10000 rpm • Supplied with test leads, croc clips, instructions & 9 volt battery

Power Probe 3Probe – Connect – Detect!• Connect to a vehicle battery and you have a multitude of testers at your fingertips!• Power-up components• Continuity tester• Voltmeter• Positive / Negative indicator• Bad ground indicator• Measures from 0 – 70 DC volts – in 1/10v increments

325200SP

MDX390SP

NEW

€1928.50

Sykes-Pickavant Battery & Electrical Systems Tester • Higher Performance model for batteries rated from 100 – 1200 CCA• Suitable for luxury and 4x4 vehicles with higher level electronic systems • Determines the state of a Battery and Electrical System • Simple & Accurate Tests - without heat or sparks being created • Integrated printer for immediate review with customer Features:- User defined printout header - Suitable for all battery types inc AGM and GEL Available Tests: - 12v batteries & electrical systems - Starting & Charging system voltage - Bad Cell detection - Test discharged batteries down to 1 volt

€579.50

FREE 12V 2A ACCU-SMART BATTERY CHARGER WHEN YOU PURCHASE MDX390SPWORTH €60.95

845122SP

Kit Contents:• Power Probe 3• Cigarette Lighter adaptor• Battery clips with heavy duty 4mm connectors• 20’ extension lead• Instruction manual

€167.50

€128.95

€95.95

BR

AKI

NG

20

Tel:

0154

3 67

9900

Portable 4 Gas Analyser with PrinterDeveloped from the 32420000 gas analyser• For fault diagnosis, tuning and pre-MOT testing• Truly portable hand-held gas analyser• Ultra light weight - only 1.1kg• Measures CO, HC, CO2, O2 (NOx model option available on request) to Class 1 accuracy• Suitable for both petrol and LPG vehicles• Ideal for both static and dynamic testing• Provides Lambda / AFR measurement and corrected CO• Internal memory stores up to 250 test results - manual & automatic recording options• Pump speed control - Improves battery life • Up to 4 hours internal battery life• Bluetooth connectivity to PC (additional software required) • Large graphic display • Free analytical software available to download • Includes printer• Includes AC & 12v chargers

03614000

Air Assisted Caliper Piston Wind Back Tool Kit• Air operated ram applies pressure to the caliper piston, while the handle is rotated by hand• Easy to use – works on standard workshop air supply• Reversible – works on both RH and LH applications• Can be used on Wind Back and Push Back pistons• Supplied with nine adaptors which cover a wide range of popular vehicles (applications list included)• Also supplied with 3/8” converter to use with adaptors from manual kit (03619200)

Brake Pipe Flaring Kits - 270 Series• Brake flaring tool that produces both Convex and Double Lap flares to SAE & DIN standards• Metric & imperial pipe sizes• From 3/16” to 1/2” / From 4.75mm to 12mm• Unique ‘Dial-a-Size’ Turret design• Lever cam operation for quick flaring• Automatic punch extraction from flare• Screw clamp for accurate die alignment• Variety of kits available to suit requirements• All components available individually

NEW

34201000

Manual Pressure Brake Bleeder • Compact solution – for easy one man operation• Portable unit – no power or air supply required• Combination of Mityvac pressure bleeder & SP aluminium pressure bleed cap• OE recommended pressure brake bleeding solution• Controllable output via hand pump and pressure gauge

NEW

€256.95

34300100Automatic Brake Bleeder - 12v• Compatible with ABS systems• 12v powering with reverse polarity warning• Includes pump with automatic shut off valve• Regulator from 0 to 3Bar• 5l reservoir with visible level and min level indication• Auto power OFF when min level reached• 12V power cable with jack (L: 4m)• Fluid cable for brake fluid with quick coupling system (Length: 4m)• Includes fluid collection bottle & European screw-on reservoir cap• Stainless steel body• Professional pump and regulator fitted

Model specific caps also available34303000

Brake Bleeder Cap - Starter Set• Starter cap bleeder set suitable for ‘343’ range of Electric Brake Bleeders• Precision engineered aluminium caps for the following applications: - New Ford Fiesta (34301000) - Nissan / Asian (Bayonet Type Cap) (34301100) - Euro Cap - Angled (Screw Type Cap) (34301400)• Full range of caps available - Contact Customer Services for details

€167.95

A professional quality tool for ensuring brake pipes are deburred effectively before fitting

FREE DEBURRING TOOL WHEN YOU PURCHASE ANY BRAKE PIPE FLARING KIT WORTH €47.40

Size Range: Internal: 3 - 12mm External: 4 - 14mm02740000

Available Kits:

Part No. Suitable for brake pipe sizes List Price

Save Price

OfferPrice

027000SPSAE Single & Double Flares: 3/16, 1/4, 5/16, 3/8, 4.75mm DIN Single Flares: 4.75mm

€308.50 €51.55 €256.95

027001SP SAE Single & Double Flares: 3/16” & 4.75mm €238.95 €40.00 €198.95

027002SPSAE Single & Double Flares: 3/16”, 4.75, 6, 8, 10mm DIN Single Flares: 4.75mm

€308.50 €51.55 €256.95

027008SPSAE Single & Double Flares: 3/16, 1/4, 5/16, 3/8, 1/2”, 4.75, 6, 8, 10, 12mm DIN Single Flares: 4.75mm

€399.95 €71.00 €328.95

027009SPSAE Single & Double Flares: 3/16, 1/4” 4.75, 6mm DIN Single Flares: 4.75mm

€277.50 €46.55 €230.95

OFFER €103.00SAVE €25.95


€746.95

WO

RKS

HO

P TO

OLS

21

ww

w.s

ykes

-pic

kava

nt.c

om14025

08245000

66088700

03890000

30044000

03950000

03860000

60080

60080-1

Elwis “Compress Flex” COB LED Hand Lamp• Adjustable light through 180°• Hanging Hook• 3W COB LED • 200 Lumen• Magnetic base• IP54 Dust Protection• Includes 230v AC adaptor & 12v car charger

Elwis Pen Light - Pack of 12• Distributor Pack of 12 pen lights• LED flash light with belt clip• Handy Magnet• Battery included

Elwis Pen Light• LED flash light with belt clip• Handy Magnet• Battery included

€139.95

€54.95

€12.95

Windscreen Wiper Arm Remover• Ideal tool for removing stubborn windscreen wiper arms• Unique design allows for four different jaw widths to be selected• Reversible and interchangeable legs• Removable centrepiece for wider applications coverage• Capacity from 19 - 36mm

Hook, Pick & Scraper Set - 9 Pc.• Hardened chrome vanadium steel• Ergonomic soft grip handles• Ideal for the fitting and removal of O rings, seals, bushes, springs, cotter pins, fuses etc• Contents: 4 x standard hooks & picks / 4 x mini hooks & picks / 1 x straight edge scraper

Heavy Duty Chain Type OilFilter Remover• Heavy duty leaf type chain• Range: 25 to 150mm diameter• Ideal for HGV, plant and industrial applications, as well as Cars / LCV’s etc• 1” hex or 1/2” sq. dr

Dual Laser Infra-Red Thermometer• High precision non-contact thermometer• Dual Laser beams are targeted on a single spot – ensures optimum distance from object for accurate temperature measurement• Temperature range: -50° to 550°C• Accuracy: +/- 1.5% at 550°C• Features: - Backlit LCD display - MAX temp display - High & Low temp alarm setting• Ideal for Aircon, Cylinder temp, Brake temp, Cooling System, Exhaust Cat etc

Valve Spring Compressor - Multivalve Engines• For the removal of valves on multivalve petrol & diesel engines• Reinforced frame made from rust-proofed steel• Supplied with 23mm & 28mm valve spring adaptors

Strap Type Oil Filter RemoverFor all filters up to 300mm diameter• Multi-purpose strap wrench, ideal for all oil filters up to 300mm circumference• Range: 20 to 300mm diameter• Strap Length: 1 metre long & 40mm wide• Strong steel shank and polyester strap• Self tightening band designed for fast and secure filter removal• Double ended 13/16” hex c/w 3/8” & 1/2” sq. dr

OFFER €59.95SAVE €17.55

LIST PRICE €77.50

OFFER €43.50SAVE €10.50

LIST PRICE €54.00


LIST PRICE €44.50

OFFER €69.50SAVE €14.45

LIST PRICE €83.95

OFFER €89.95SAVE €13.55



LIST PRICE €38.95

WO

RK

WEA

R

22

Tel:

0154

3 67

9900

Lee Cooper Quilted Jacket - Black• 100% nylon jacket with boxed quilt effect design• 100% polyester light weight padding• Zip fastening to both front & hand pockets• Fully functional chest pocket with contrast zip

LCJKT436

LCPNT205

LCTS003

LCPNT208

SPWF66 / SPWF55

LC022

LCSCK603

LCKP

Available sizes:M, L, XL, XXL

€79.95

€29.95

€19.95

€9.95 €45.00

€49.95

€14.95

€67.50

Lee Cooper Hi-Top Safety Boot• Available in UK sizes: 7 - 12• Lightweight & Flexible with modern styling• Low profile anti-slip rubber sole• Steel Toe Cap to ISO20345 standard• PU Fabric Upper with textured rubber toe cap cover

Lee Cooper Heavy Duty Work Socks• Pack of 5 pairs - one size fits all

Lee Cooper Cargo Work Trousers - Black• 2 combat thigh pockets• Pocket flaps with velcro• Zip fly• Belt loops• 65% polyester / 35% cotton twill

Available in waist sizes:32”, 34”, 36”, 38”, 40”, 42”

Available in leg lengths:Short (30”) Regular (32”) Long (34”)

Lee Cooper Knee Pads for Lee Cooper Cargo / Holster Trousers • Suitable for use with LCPNT206, LCPNT208 and LCPNT216 trousers• Material: EVA flexible

SPWF55

SPWF66

SP Safety Trainer / Boot - Moulded Sole• Available in UK sizes: 7 - 12• Dual Density PU, Oil & Acid Resistant• Steel Toe Cap to ISO20345 standard• Black Suede / Grey Mesh Upper• Steel Toe Cap & Mid-Sole

Available in waist sizes:32”, 34”, 36”, 38”, 40”, 42”

Available in leg lengths:Short (30”), Regular (32”) Long (34”)

Lee Cooper Cargo Trousers - Black / Grey• Two colour trouser combining comfort & functionality• Extending velcro fastening tool belt loop• Adjustable elasticated gripper waistband • Triple stitched seams• Top loader knee pad pockets• High abrasion resistant contrast panelling to leg hem panels• 2 x front pockets, 2 x bellow back pockets, 2 x pleated leg pockets, Pen pocket, Phone pocket• 65% polyester / 35% cotton double warp double weft canvas fabric

Lee Cooper Technical Polo Shirt - Black• Sportswear design, fit & styling• Contrasting red placket and grey side panels with pockets• 100% polyester pique fabric

Available in sizes:M, L, XL, XXL, XXXL

Sykes-Pickavant Ltd, Unit 4 Cannel Road, Burntwood Business Park, Burntwood, Staffordshire, WS7 3FU. United KingdomTel: +44 (0) 1543 679900 Fax: +44 (0) 1543 679901 e-mail: [email protected] www.sykes-pickavant.com

BATTERY CARE

ALL PRICES QUOTED EXCLUDE VAT & ARE SUBJECT TO AVAILABILITY - E&OE - PRICES VALID UNTIL 30TH JUNE 2014 - REF: SPQ214EUROCOPYRIGHT 2014 - SYKES-PICKAVANT LTD. ALL RIGHTS RESERVED.

Extend your batteries’ lifetime with Accu-Smart®A totally automatic charger that works for you Accu-Smart®, electronic “switched-mode” battery charger, offers greater power compared to old chargers using “linear-mode technology” with transformers.• Suitable for Wet (Lead Acid), AGM, Gel & Fleece type batteries • No need for handling or mode selection, the charger works automatically, without external intervention, therefore it is not necessary to disconnect the battery from the vehicle before charging it• Accu-Smart® disposes of a regulator which allows the totally secure charging of the battery• Manages and regulates the charge of the battery, so can be left connected on the battery permanently• The Accu-Smart® charger restarts in case of a power cut and provides total protection against short-circuits, peaks of voltage (AC or DC), inversion of polarity and over-heating spikes

NEW MODELSNOW AVAILABLE

High quality Battery Booster Packs, covering a wide variety of applications including: Automotive, Agriculture, Plant, HGV, Marine & Aviation

All Pro-Start booster packs are perfectly safe for the on-board electronics on modern vehicles and are compatible with Petrol, Diesel & Hybrid vehicles• AGM internal batteries deliver high amperage instantaneously (2 year warranty)• Double insulated starting cables – 1.30 / 1.35 mtrs length• Illuminated voltmeter indicates booster charge level, booster & alternator function• Internal fuse protects against short circuits• Curved jaw clamps, fully insulated – blue clamp with LED lamp for safe use in the dark• Single-piece, moulded case – shock resistant (lifetime warranty on case)Other models available - Ask for details

Part No. Rating Applications Accessories Included Price

845121SP 12 volts / 1 Amp Eyelets, Crocodile Clamps €45.00

845122SP 12 volts / 2 Amps Eyelets, Crocodile Clamps, Cigarette Lighter Plug €60.95



845243SP 24 volts / 3.5 Amps Eyelets, Crocodile Clamps €116.00

NEW

NEW

NEW

861001SP 861002SP

521001AC 521001DC 521002AC 521002DC

Pro-Start 700 12v Battery Booster Pack• Cranking Amps: 700• Peak Amps: 1860

Pro-Start 800 12v Battery Booster Pack• Cranking Amps: 800• Peak Amps: 2370

Propulstation 12v AC Battery Booster Pack• Cranking Amps: 700• Peak Amps: 1860

Propulstation 12v DC Battery Booster Pack• Cranking Amps: 700• Peak Amps: 1860

Propulstation 12v AC Battery Booster Pack• Cranking Amps: 800• Peak Amps: 2370

Propulstation 12v DC Battery Booster Pack• Cranking Amps: 800• Peak Amps: 2370

€354.95

€588.50 €535.50 €670.95

€619.50

€457.95

PROPULSTATION Booster Pack complete with Docking StationEliminates the risk and frustration of an uncharged booster pack!

Distributor Stamp:

PROPULSTATION eliminates the risk and frustration of an uncharged booster pack due to the unique docking station. This means that it is always in the right place, always charged 100% and has 3 times longer lifetime.• AGM internal batteries deliver high amperage instantaneously (2 year warranty)• Robust shell case design with 5mm shatterproof polyethylene • Long and flexible cables with a double insulation offer a perfect resistance to extreme conditions• Robust, wide-opening clamps which are fully insulated and have a copper trace carrying the current to both of the bronze jawsChoose from: • AC model: Supplied with mains AC charger for workshop / showroom use• DC model: Supplied with 5m cable and one-way diode for vehicle use Other models available - Ask for details

workshop solutions special offers - sykes …sykes-pickavant.com/downloads/sykes-pickavant - q2 2014...

Documents