rear axle/suspension - seekpartfile.seekpart.com/keywordpdf/2011/3/22/201132284812410.pdfaxle...

© XKs Unlimited 2005268XKs Unlimited • 850 Fiero Lane, San Luis Obispo, CA • (805) 544-7864 • (800) 444-5247 (JAGS) • Fax (805) 544-1664

Rear

Sus

pens

ion/

Diffe

rent

ial

1. Pinion Seal (ENV) ___________________________ 02-WLG-162. Pinion Seal (Salisbury) _________________________ JA-38403. Gasket on Pinion Seal, Salisbury _____________ JA-607183-J4. Inner Axle Seal (ENV) ________________________ 02-WL-1815. Inner Axle Seal (Salisbury) ______________________ JA-38486. Hub Bearing Adjusting Shim (.003") _______________ JA-38677. Hub Bearing Adjusting Shim (.005") _______________ JA-38688. Hub Bearing Adjusting Shim (.010") _______________ JA-38699. Hub Bearing Adjusting Shim (.030") _______________ JA-387010. Hub Seal Only (ENV) _________________________ C24611-211. Hub Seal Only (Salisbury) _________________________ C148112. Hub Seal & Retainer Assy, Salisbury _____________ C1481/8013. Pinion Bearing, Front (ENV) _____________________ 12-001014. Pinion Bearing, Front (Salisbury) _________________ 13-384315. Pinion Bearing, Rear (ENV) _____________________ 12-002016. Pinion Bearing, Rear (Salisbury) __________________ 13-384417. Carrier Bearing (ENV) __________________________ 12-003018. Carrier Bearing (Salisbury) ______________________ 13-3845

19. Axle Bearing (ENV) ____________________________ 12-003020. Axle Bearing (Salisbury) ________________________ 12-004021. Differential Gasket (Salisbury), Early XK-120 & MK VII JA-384722. Differential Gasket, Later Type ___________________ JA-393123. Pinion Gear Nut ______________________________ JA-1109924. Axle Shafts, (Salisbury only) _____________________ JA-392425. Axle Shaft Nut-1"x14 TPI (Salisbury only) ____________ JA-13126. Axle Shaft Washer _______________________________ C147927. Ring & Pinion Gear Sets ___________________ See Page 28028. Splined Hubs _____________________________ See page 25429. Gasket, behind oil seals, Salisbury __________________ C148330. Wheel Lug Nut, all with disc wheels _________________ C304131. Clamp, Brake Line to Axle (not for brake cable) ________ C361732. Stud, Nut & Washer, holds brake drum to hub,

XK-120 & XK-140 with wire wheels __________________ C627733. Key __________________________________________ C7356Hardware Not Shown:34. Bolt, rotor to hub, XK-150 with wire wheels ___________ C1354635. Wheel Stud, XK-150 with disc wheels _______________ C13365

Note: Salisbury axles (asshown) have a stamped steelinspection plate at the rear;ENV axles do not have aremovable cover.

1. Leaf Spring, XK-120 or XK-140 (replace in pairs) _____ 12-00502. Leaf Spring, XK-150 (replace in pairs) _____________ 12-00513. Leaf Spring, MK VII, VIII, IX (replace in pairs) ________ 12-0054Note: Springs are supplied with “eye” bushings.4. Spring “Eye” and Shackle Bushing, 6 required _________ C12195. Lock Tab, Leaf Spring Shackle Bolt, one per side ______ C36516. Upper Shackle Bolt ______________________ JA-NB.143/23F7. Lower Shackle bolt ______________________ JA-NB.143/28F

Rear Axle: XK-120, XK-140, XK-150; MK VII, VIII, IX

Rear Axle/Suspension

Rear Suspension: XK-120, XK-140, XK-150; MK VII, VIII, IX8. Rebound Buffer, Upper, all ________________________ C32089. Taper Wedge, between axle & spring ______________ 12-005310. Rebound Buffer, Lower, XK-120 & MK VII only ________ JA-63211. "U" Bolt, XK-120, XK-140, XK-150, each _____________ C775212. Leather Spring Gaitor Set. High quality, made in England.

Will cover two springs. __________________________ C3877/813. Spacer/Washer, spring "eyes", Std. ________________ JA-86914. Spacer/Washer, spring "eyes", .020" oversize _____ JA-869/OS

22

1, 2

4, 5

4, 5

12

13, 14

15, 16

17, 18

17, 18

21 19, 20

23

24

25

27

29

3

30

28

31

32

6-9

26

10, 11

33

9

1-346

7

8 4 4

51012

11

13, 14

13, 14

13, 14

13, 14

269XKs Unlimited • 850 Fiero Lane, San Luis Obispo, CA • e-mail: [email protected] • Web Site: www.xks.com

© XKs Unlimited 2005

Rear Suspension/Differential

Rear Axle

1. Gasket, Differential Cover ______________________ JA-39312. Axle Shaft, MK II Only _________________________ 12-79953. Axle Nut ____________________________________ JA-41414. Pinion Seal _________________________________ JA-38405. Pinion Seal Gasket _______________________ JA-607183-J6. Axle Seal ___________________________________ JA-41447. Hub Seal and Metal Plate Assembly ______________ JA-79538. Hub Seal Only _____________________________ 02-WLP-329. Pinion Bearing, Front __________________________ 13-384310. Pinion Bearing, Rear __________________________ 13-384411. Carrier Bearing, 2 required _____________________ 13-384512. Axle Bearing, 2 required _______________________ 12-004513. Splined Hub, Wire Wheels, Right _________________C1309414. Splined Hub, Wire Wheels, Left___________________C1309515. Wheel Stud, disc wheels only ___________________ C1336516. Clutch Pack, limited slip diffs only ________________ 13-010017. Shim Kit for ring & pinion _______________________ 13-0101

Rear Axle: MK I & MK II18. Brake Line Clamp _____________________________ C361719. Ring & Pinion Gear Sets __________________ See 8020. Hub Bearing Adjusting Shim, .003" _______________ JA-414521. Hub Bearing Adjusting Shim, .005" _______________ JA-414622. Hub Bearing Adjusting Shim, .010" _______________ JA-414723. Hub Bearing Adjusting Shim, .030" _______________ JA-414824. Differential Adjusting Shim, .003" ________________ 13-393525. Differential Adjusting Shim, .005" ________________ 13-393626. Differential Adjusting Shim, .010" ________________ 13-393727. Differential Adjusting Shim, .030" ________________ 13-393828. Bolt, brake rotors to hubs, wire wheel cars only ______C1354629. Lug nut, disc wheels only _______________________ C304130. Bolt, caliper to adaptor plate, 3.4 to VIN 175123,

3.8 to VIN 210686 _____________________________C1438331. Bolt, caliper to adaptor plate, 3.4 VIN 175124 to

177359, 3.8 210687 to 217695 ___________________C16262Please call if you require a component that is shown butnot listed.

13, 14

1

2

3

4

5

67, 8

9

10

11

11

12

15

16

16

17

18

18

19

20-23

24-27

28 29

3031


Rear

Sus

pens

ion/

Diffe

rent

ial

Rear Suspension

1. Front Spring Pad _____________________________ C108432. Leaf Spring (includes eye bushing & center pads) __ C10791-23. Center Mounting Pad, OE style, 4 required _________ C108444. Center Mounting Pad Kit, polyurethane, car set _____ 17-60015. Spring Eye Bushing, 2 required ___________________ C89396. Spring Eye Bushing, 2 required, polyurethane, car set 17-60027. Torque Arm Bushing only, 4 required _______________C89498. Torque Arm Bushing Kit, polyurethane, 2 required ___ 17-60249. Torque Arm (does not include bushings)___________ C1109110. Bushing Tube, for ends of panhard rod tube _________C1104811. Adjusting End Only ____________________________C1199612. Panhard Rubber Bushings, 4 required ____________ C10995

Rear Suspension: MK I & MK II13. Panhard Rubber Bushings, 1 set required, polyurethane _ 17-600314. Panhard Rod only _____________________________C1414015. Complete Panhard Rod Assembly _______________ 14-300016. Outer Washer on Panhard Rod, 4 required _________ C1104217. Inner Washer open Panhard Rod, 4 required ________C1104318. Panhard Bracket for RH Spring Hanger, MK I & II ___ 16-302519. Clamp Assembly for LH Spring Hanger, MK I & II ____ 16-302620. Spring Clamp Plate, 2 required _________________ 16-3026A21. Shocks (Please see page 144)22. Standard Rear Suspension Bushing Kit, includes items

1, 3, 5, 7, & 12 ______________________________ 12-100023. Polyurethane Rear Suspension Bushing Kit, includes items

4, 6, 8, & 13, (Not pad, #1) _____________________ 17-602624. Nut, Panhard Rod Adjusting ________________JA-NT609041

16

1616

1

1

2

3, 4

3, 4

3, 4

5, 6

7, 8

7, 8

7, 8

7, 8

1110

10

12, 13 24

12, 13

15

1717

9

9

5, 6

2

7, 8

19

18

14

20

20

21

21




Earlier Final DriveA Style: 3.8 E-Type & Early 4.2 Series I, Early Mark 10, 3.4S and 3.8SB Style: Late Series I E-Type, Series II except 3rd type, 420, 420G

Differential

1. Pinion Seal _________________________________ JA-3840

2. Pinion Seal Gasket _______________________ JA-607183-J

3. Roller Bearing Outer Pinion _____________________ 13-3843

4. Outer Shim, .003" (as required) __________________ 13-3856




8. Distance Washer _____________________________ 13-8029

9. Crush Sleeve, Ser. II, 2nd & 3rd Type ____________ 13-12456

10. Inner Shim, .003" (as required) __________________ 13-3960



13. Inner Pinion Roller Bearing _____________________ 13-3844

14. Carrier Roller Bearing, 2 required ________________ 13-3845

15. Gasket, Differential Cover ______________________ JA-3931

16. Bolt, Flange to Half Shaft_______________________ JA-8510

17. Stub Axle Lock Nut ____________________________C15349

18. Bearing Housing Oil Seal, 2 required _____________ JA-8436

19. Drive Shaft Roller Bearing, Early , 4 required _______ 13-8495

20. Drive Shaft Roller Bearing, Late, 4 required _______ 13-11101

21. Spacing Collar, Early, 2 required _________________ 13-8493

22. Spacing Collar, Late, 2 required ________________ 13-11102

23. Shim, .003" (as required) _______________________ 13-8490

24. Shim, .005" (as required) _______________________ 13-8491

25. Shim, .010" (as required) _______________________ 13-8492

26. Shim, .003" (as required) ______________________ 13-11103

27. Shim, .005" (as required) ______________________ 13-11104

28. Shim, .010" (as required) ______________________ 13-11105

29. O-Ring, 2 required ____________________________ JA-8950

30. Tab Washer, 2 required _______________________ 13-11108

31. Shim, .003" (as required) _______________________ 13-9754

32. Shim, .005" (as required) _______________________ 13-9755

33. Shim, .010" (as required) _______________________ 13-9756

34. Shim, .030" (as required) _______________________ 13-9757

35. Clutch Pack, For Limited Slip Diffs _______________ 13-0100

36. Bolt, differential to I.R.S. “cage”, 4 required ___ JA-JZS100090

37. Ring & Pinion Gear Sets __________________ See Page 280

38. Ring & Pinion Shim Kit ________________________ 13-0101

39. Bolt, Flange to Half Shaft_______________________ JA-8510

40. Oil Additive for limited-slip diff’s (brand may vary)____ 13-0102

41. Tab Washer, "A" Style only _____________________ JA-8498

42. Pinion Nut _________________________________ JA-11099

Early-Type I.R.S. Differential

36

26-28

18 20 22 29 20 30

9

31-34

3

21

31-34

29

19 2123-25

19

184-7

8

10-12

13

35

14

14

15

B Style

A Style

37, 38

40

3917 16

41


Rear

Sus

pens

ion/

Diffe

rent

ial

12-15

16

17

20

19

22, 2331 B Style

DifferentialLater Final DriveA Style: E-Type S. II 3rd Type, E-Type S. III, XJ-6 Ser. I3rd Type, XJ-6 S. II W/O SuffixB Style: XJ-6 Series II W/Suffix X or S, XJ-6 Series III, all XJ-S

1. Pinion Nut _________________________________ JA-110992. Pinion Seal, 1-9/16" I.D. for final drives that have I.D. numbers with no

suffix, (flange seal face has an outside diameter of 1.57") __ JA-38403. Pinion Seal, 1-7/8" I.D., Leather. For final drives that have I.D.

numbers with a suffix of “S” or “X”, (flange seal face has anoutside diameter of 1.88") ___________________ JA-JLM527

4. Pinion Seal, 1-7/8" I.D., Neoprene. For final drives that haveI.D. numbers with a suffix of “S” or “X”, (flange seal face has anoutside diameter of 1.88") __________________ JA-CBC6923

5. Pinion Seal Gasket _______________________ JA-607183-J6. Slinger, Oil _______________________________ JA-JLM6147. Roller Bearing ______________________________ 13-124658. Crush Sleeve _______________________________ 13-124569. Inner Shim, .003" (use as required) _______________ 13-386010. Inner Shim, .005" (use as required) _______________ 13-386111. Roller Bearing, Inner Pinion____________________ 13-1225212. Shim, .003" (use as required) ___________________ 13-393513. Shim, .005" (use as required) ___________________ 13-393614. Shim, .010" (use as required) ___________________ 13-393715. Shim, .030" (use as required) ___________________ 13-393816. Roller Bearing, Carrier, 2 required________________ 13-384517. Tab Washer, 2 required _____________________ JA-JLM55618. Roller Bearing, “X” suffix or no suffix on diff I.D. ____ JA-12261

19. Roller Bearing , with Suffix “S”, 4 required ______ JA-RTC134720. Crush Sleeve, Suffix “S”, 2 required __________ JA-RTC134821. O-Ring, “X” suffix or no suffix __________________ JA-1247322. O-Ring; Suffix “S”, 2 required ________________ JA-RTC134023. O-Ring, Dana differentials only, 2 required ______ JA-JLM29224. Shim, .003" (use as required) __________________ 13-1247425. Shim, .005" (use as required) __________________ 13-1247526. Shim, .010" (use as required) __________________ 13-1247627. Shim, .030" (use as required) __________________ 13-1247728. Gasket, inspection cover _______________________ JA-393129. Oil Seal, “X” suffix or no suffix _______________ JA-RTC121630. Locknut, Halfshaft Stub Axle, 4 required per axle _____C1534931. Oil Seal , I.D. numbers with a Suffix “S” ________ JA-JLM126432. Lockplate, carrier, 5 required ____________________ JA-631633. Lockplate, spider gears, B-Style, 2 required ________ JA-385434. Lockplate, spider gears, B-Style, 2 required ________ JA-385535. Breather _____________________________________C2571636. Breather Elbow ______________________________ JA-850937. Bolt, differential to I.R.S. “cage”, 4 required ___ JA-JZS10009038. Ring & Pinion Gear Sets __________________ See Page 28039. Clutch Pack, For Limited Slip Diffs _______________ 13-010040. Ring & Pinion Shim Kit ________________________ 13-010141. Oil Additive for Limited-Slip Diff's (brand may vary) __ 13-0102

Later-Type I.R.S. Differential

1

2-4

5

6

7

8

9, 10

11

12-151617

18

21

24-27

29

32

33

3334

34

37

A Style

38

28

35

36

39, 40

41

See page xxx for rebuiltstub-axle assemblies.

30

30




Rear Suspension

1. Outer Thrust Washer, 8 required __________________C17165

2. Retainer, 8 required ____________________________C17936

3. Rubber Sealing Ring, 8 required __________________C17213

4. Inner Thrust Washer, 8 required __________________C17166

5. Needle Bearing, 8 required _____________________ C17167

6. Bearing Tube, early 3.8 E-Type (1.75"), 4 required ____C17168

7. Bearing Tube, all except above (1.125"), 4 required _ C17168-1

8. Distance Tube, 2 required _____________________ C17663-1

9. Fulrum Shaft, 2 required ________________________C1700810. Inner Shim, .003" (as required) ___________________C1662611. Inner Shim, .007" (as required) _________________ C16626-3

12. Sleeve, 4 required ___________________________ C16623-1

13. Bearing, 4 required ____________________________C16029

14. Seating Ring, 4 required ________________________C16628

15. Spacer, 4 required _____________________________C20180

16. Rubber Seal, 3.8 E-Type to 877182 (OTS) & 885984 (FHC) C16627

17. Felt Seal, all later applications, 4 required__________ C20178

18. Container, 4 required ___________________________C20179

19. Retaining Washer, 4 required ___________________ C2018220. Outer Shim, .003" (as required) _________________ C16626-121. Outer Shim, .007" (as required) _________________ C16626-2

22. Shaft, cars without tie-down brackets ______________C16624

23. Shaft, cars with tie-down brackets (most XJs)___ JA-CBC9118

24. Nut ________________________________________ C8667-7

25. Rear Trailing Arm Bushing, OE, 2 required __ JA-MHC3160AA

26. Rear Trailing Arm Bushing, Aftermarket, 2 req’d. JA-MHC3160AA*

27. Front Trailing Arm Bushing, OE, 2 required _ JA-MHC3170AA

28. Front Trailing Arm Bushing, Aftermarket, 2 req’d. JA-MHC3170AA*

29. Safety Strap, Series I & II E-Type FHC & OTS _______C1903130. Safety Strap, Series I and II E-Type 2+2, all Series III C2515631. Safety Strap, Series II and III XJ-6, XJ-S ____ JA-LHD5642AA32. Bolt, For Trailing Arm Safety Strap, 2 required __ JA-CBC9362

33. Bolt, Ser. I & II E, 420G/MK X, 420, 3.8S, 2 required C17149-1

34. Bolt, V-12 E-Type, XJ-6, XJ-12, XJ-S, 2 required _____C25365

35. Lock tab, for C25635 bolt, later applications _________C25401

36. Nut, on trailing arm bolt, early applications only _____ C8737-5

37. Bolt, front of bracket to differential, 2 required__ JA-JZS100088

38. Bolt, rear of bracket to differential, 2 required __ JA-JZS100089

39. Shim, .005" (as required) ________________________C28427

40. Shim, .007" (as required) ________________________C28428

41. Shaft, lower shock mount, 2 required ______________C17013

42. Sleeve on Shaft, 2 required _____________________ C29374

43. Washers on Shaft, 4 required ____________________ C3052

44. Sleeve in Upper Eye of Shock, 4 required__________ C17012

45. Nut, Inner Pivot Shaft _______________________ 16-13050Z

46. Nut, Shock Shaft ___________________________ 16-13041Z

47. Trailing Arm, with Bushings, E-Type Six Cylinder _____C2382448. Trailing Arm, with Bushings, E-Type V-12 __________ C3794549. Trailing Arm, with Bushings, XJ-6; XJ-S w/o anti-roll bar C2931050. Trailing Arm, with Bushings, XJ-S with anti-roll bar ____C41831

Wishbone Radius Arm—Independent Rear Suspension

25, 26

27, 28

29-3132

35

33, 34

38

37

39, 40

41

43

6, 7

54

3

21

13

1415

16, 171819

20, 21

22, 23

98

12

47-50

10, 11

24

42

36

45

4644


Rear

Sus

pens

ion/

Diffe

rent

ial Independent Rear Suspension Hub Assembly

Rear Suspension

1. Seating Ring, 2 required ___________________ JA-CCC6807

2. Inner Oil Seal, 2 required________________________C15231

3. Spacer (.110"), use as required ___________ JA-CCC6806-10





















24. Inner Bearing, 2 required ________________________C15230

25. Outer Bearing, 2 required ______________________ C19066

26. Wheel Bearing Kit. Large type only. Includes one each: inner &outer oil seals, inner & outer bearings. Two req'd. (For smalltype, assemble kit from parts.) ______________14-QWB137C

27. Outer Oil Seal. Early Small Type; all 3.8 E-Type OTS; 4.2 E-TypeOTS to VIN 1E10978 and FHC to VIN 1E31002; 3.4S to 1B.25707,3.8S to 1B.78500; MK 10 3.8; 3-1/4" approx. O.D. _______C19068

28. Outer Oil Seal. Late large type; 4.2 E-Type roadster from VIN1E10979, 4.2 E-Type FHC from VIN 1E.31003, all 2+2 Series I,all E-Type Series II & III, LHD 3.4S from 1B.25708, LHD 3.8Sfrom 1B.78501; MK X 4.2, 420G, 420 and XJs.3-3/8" approx. O.D. ____________________________C24789

29. Seating Ring . Early small type; all 3.8 E-Type OTS; 4.2 E-Type OTSto VIN 1E10978 and FHC to VIN 1E31002; 3.4S to 1B.25707, LHD3.8S to 1B.78500; MK 10 3.8; 2-1/2" approx. O.D. _______C19067

30. Seating Ring. Late large type; 4.2 E-Type OTS from VIN1E10979, 4.2 E-Type FHC from VIN 1E.31003, all 2+2 Series I,all E-Type Series II & III, 3.4S from 1B.25708, 3.8S from1B.78501; MK X 4.2, 420G, 420 and XJs.2-7/8" approx. O.D. ____________________________C24791

31. Wheel Studs, as required ______________________ C13365

32. Washer, 2 required ____________________________C24923

33. Nut, 2 required _________________________ JA-ND612041J

34. Hub, Bolt-On Wheels, 2 required_____________ JA-CBC1784

35. Cap, 2 required ______________________________ C18124

36. Hub Carrier, Large Type Bearing Only, Bare Casting _ C26699

1

2 3-23 24

25

27, 28

29, 30

31

33

32

34

35

36

Note: This type of hub carrier was used onall pre-XJ IRS cars and XJ-6 and XJ-12Series I, II and III. It was used by the XJ-S toVIN 188104 (mid-1993 model year), when ahybrid rear suspension was introduced withXJ-40-type hub carriers and outboardbrakes. See next page for post-188105 XJ-S.




Please call if you require acomponent that is shown butnot listed.

1-2627, 28

29, 3930, 39

33

34, 3935, 39

36

37

31

32

38

XJ-40 Differential

Rear Hub Carrier & Hub AssemblyAdjustable Bearing Spacer, as required:

40 41, 42

43

45-47

44

48

49-61

62

63

64-6768

69

70

XJ-40 (1988-1994 XJ-6) Hub Carrier and DifferentialDifferential

40. Viton Seal ______________________________ JA-CBC692341. Pinion Spacer, to 633429 ___________________ JA-JLM61442. Pinion Spacer, 633430-on _________________ JA-JLM1078243. Bearing Assembly ________________________ JA-ATA716644. Collapsible Spacer___________________________ 13-1245645. Inner Pinion Bearing Shim, .003" ________________ JA-386046. Inner Pinion Bearing Shim, .005" ________________ JA-386147. Inner Pinion Bearing Shim, .010" ________________ JA-386248. Bearing Assembly ___________________________ 13-12252

1. 2.22 mm_ JA-CBC9505-12. 2.27 mm_ JA-CBC9505-23. 2.32 mm_ JA-CBC9505-34. 2.27 mm_ JA-CBC9505-45. 2.42 mm_ JA-CBC9505-56. 2.47 mm_ JA-CBC9505-67. 2.52 mm_ JA-CBC9505-78. 2.57 mm_ JA-CBC9505-89. 2.62 mm_ JA-CBC9505-910. 2.67 mm JA-CBC9505-1011. 2.72 mm JA-CBC9505-1112. 2.77 mm JA-CBC9505-1213. 2.82 mm JA-CBC9505-13

27. Bearing Spacer (1988 & 1989), 2 required _____ JA-CAC582528. Bearing Spacer (1990-on), 2 required _________ JA-CBC820729. Outer Bearing, 2 required __________________ JA-CAC633330. Outer Seal, 2 required _____________________ JA-CCC446631. Cone, 2 required _________________________ JA-CBC665232. Nut, 2 required __________________________JA-JZN10003533. Seal Track Spacer (1988 & ’89), 2 required ____ JA-CAC721634. Rear Inner Seal, 2 required _________________ JA-CBC170635. Rear Inner Bearing, 2 required ______________ JA-CAC633236. Blanking Plug (1988 & 1989), 2 required_______ JA-CAC745237. Taper Roller Bearing, 2 required _____________ JA-CAC461038. Sleeve, pivot pin, 2 required ________________ JA-CAC584639. Rear Hub Bearing Kit, contains inner and outer

bearings and seals plus grease _______________ 14-QWB708

14. 2.87 mm JA-CBC9505-1415. 2.92 mm JA-CBC9505-1516. 2.97 mm JA-CBC9505-1617. 3.02 mm JA-CBC9505-1718. 3.07 mm JA-CBC9505-1819. 3.12 mm JA-CBC9505-1920. 3.17 mm JA-CBC9505-2021. 3.22 mm JA-CBC9505-2122. 3.27 mm JA-CBC9505-2223. 3.32 mm JA-CBC9505-2324. 3.37 mm JA-CBC9505-2425. 3.42 mm JA-CBC9505-2526. 3.47 mm JA-CBC9505-26

49. .028" ____ JA-JLM563-A50. .030" ____ JA-JLM563-B51. .031" ____ JA-JLM563-C52. .032" ____ JA-JLM563-D53. .033" _____ JA-JLM563-E54. .034" _____ JA-JLM563-F55. .035" ____ JA-JLM563-G

56. .036" ____ JA-JLM563-H57. .037" _____ JA-JLM563-I58. .038" _____ JA-JLM563-J59. .039" ____ JA-JLM563-K60. .040" _____ JA-JLM563-L61. .045" ____ JA-JLM563-M

62. Bearing Assembly, 2 required ___________________ 13-384563. Bearing Retaining Collar, 2 required ___________ JA-JLM61564. Shim, 1.0mm, as required __________________ JA-JLM111765. Shim, 1.05mm, as required _________________ JA-JLM111866. Shim, 1.10mm, as required _________________ JA-JLM111967. Shim, 1.15mm, as required _________________ JA-JLM112068. Ball Bearing, 2 required ___________________ JA-JLM1152769. O-Ring, 2 required _________________________ JA-JLM62170. Oil Seal, Triple Lip, 2 required ________________ JA-JLM61871. Wheel Stud _____________________________ JA-CAC3878

Differential Bearing Shims, As required:

See next page for rebuiltstub-axle assemblies

71


Rear

Sus

pens

ion/

Diffe

rent

ial

Year/Model Ratio Description Part NumberXJ-6 S. I & II 3.54 Open ______________________________________________ JA-CAC2391/RBXJ-6 S. I & II 3.31 Open ______________________________________________ C41049/RBXJ-6 S. III 3.07 Open ______________________________________________ C43123/RBXJ-6 S. III 2.88 Open ______________________________________________ JA-CBC2104/28/RB88-89.5 XJ-40 2.88 Round Flange, Powr-Lok _______________________________ JA-JLM1292/28/RB88-89.5 XJ-40 2.88 Round Flange, Open __________________________________ JA-JLM1371/28/RB1988 XJ-40 2.88 Jurid Flange, Open ___________________________________ JA-JLM1775/28/RB1988 XJ-40 2.88 Jurid Flange, Powr-Lok ________________________________ JA-JLM1776/28/RB1988 XJ-40 4.09 Round Flange, Powr-Lok (European Only) _________________ JA-JLM1292/49/RB1988 XJ-40 3.54 Round Flange, Open (European Only) ____________________ JA-JLM1371/35/RB1988 XJ-40 3.54 Round Flange, Powr-Lok (European Only) _________________ JA-JLM1292/35/RB1988 XJ-40 3.58 Round Flange, Powr-Lok _______________________________ JA-JLM1292/38/RB89 - 97 XJ-6 3.77 Jurid Flange, Open (European Only) ______________________ JA-JLM10780/37/RB89 - 97 XJ-6 3.58 Jurid Flange, Open ___________________________________ JA-JLM10780/38/RB89 - 97 XJ-6 3.58 Jurid Flange, Powr-Lok ________________________________ JA-JLM10781/38/RB89 - 97 XJ-6 4.09 Jurid Flange, Open (European Only) ______________________ JA-JLM10780/49/RB89 - 97 XJ-6 4.09 Jurid Flange, Powr-Lok (European Only) __________________ JA-JLM10781/49/RB81 - 87 XJ-S 2.88 Powr-Lok ___________________________________________ JA-CBC1957/28/RB84 - 85 XJ-S 2.88 Dana Diff., Powr-Lok __________________________________ JA-CAC9281/RB88 - 93 XJ-S 2.88 With ABS, Powr-Lok __________________________________ JA-EBC9429/28/RB94-on XJ-S 2.88 With ABS, Powr-Lok __________________________________ JA-NHC5700AB/1/RB

Rebuilt DifferentialsWe now have available a complete range of rebuiltdifferential for XJ Jaguars. These premium rebuilds carrya 12-month/12,000-mile warranty from the date of installa-tion. We stock the more popular units, but any non-stocked differential can be drop-shipped from ourrebuilder. In Jaguar parlance, “Powr Lok” indicates alimited-slip unit. Core charges apply. Note: All unitslisted as “Jurid Flange” have a rubber donut wherethe drive shaft meets the differential. The shaft isattached with three bolts. All “Round Flange” unitsuse a conventional steel flange and are attached withfour bolts. Do not trust what “should” be in the car;please inspect before ordering.

Rebuilt Stub Axle AssembliesThese complete assemblies are all about labor savings,because the time-consuming press work has already beendone. All wear items, such as bearings and seals arereplaced. Ready to bolt on.XJ-S and XJ-6 Series III, Right __________ JA-JLM558/RBXJ-S and XJ-6 Series III, Left ___________ JA-JLM559/RBXJ-S with Dana Differential, Right or Left _____ JA-JLM313XJ-40 (1988-1994), Right or Left_________ JA-JLM630/RBX-300 (1995-1997), Right or Left ______ JA-JLM12137/RB

Rebuilt Steering Pump AssembliesWith most cars, changing a power steering pump is arelatively simple procedure. Not so with the 1988 to 1997XJ-6. The engine-driven pump’s drive gear is pressedonto the pump inside a fragile alloy housing, which is notpart of the rebuilt pump sold by Jaguar dealers. We’vereceived more than one customer core with broken partsof the housing still attached. With our rebuilt assemblies,however, all the tough work is done for you because thedrive and housing come already pressed on, making for atruly bolt-on operation. Save time, save money.XJ-40 (1988-1994 XJ-6) _______ JA-MMD8110AA/R-ASMX300 (1995-1997 XJ-6) ________ JA-MNA8110AM/R-ASM




Mr. Moly Gear Aide is a heavy dutymulti-grade oil with extreme pressureadditives to assist in rapid plating ofmolybdenum disulfide to gears, bearings , splines, etc. Greatlyimproves shifting effort 10 fl. oz. _________________ LE-53422

Mr. Moly Engine Aide contains small particles (.5 microns) ofmolybdenum disulfide in a heavy duty multi-grade oil. Theparticles are so small they will not be filtered out. One treatment ofat least 5 percent of engine oil capacity will last 10,000 miles LE-53412

Mr. Moly PLD penetrates, lubricates, and disperses moisture. Anall-purpose product with innumerable uses in industry, automotive,and home. Cannot be shipped by air. _____________ LE-53432

Mr. Moly Break In prevents metal scuffing, but permits the wearof high spots while allowing for full lubrication flow duringrunning-in period. (Not shown) _________________ LE-55942

Limited Slip DifferentialFriction Modifier

Most people don’t know that the Jaguar limited slipdifferential requires a special oil additive to functionproperly and quietly. Whenever rebuilding thedifferential or changing the oil, you should addone bottle. Brands may vary. ___________ 13-0102

Copaslip Anti-Seize CompoundFor wire wheel splines. Ever tried to remove a wire wheelthat's rusted to a splined hub? That's why you're supposed touse this. __________________________________ 17-0212

"Stat-O-Seal"WashersNo one ever accused Jaguar enginesand other fluid-filled components of being oil-andwater-tight. These alloy washers, widely used in racecars, incorporate an internal rubber o-ring as a secondline of defense against leaks. A great product.1/4" ___________________________________________ 17-19945/16" __________________________________________ 17-19953/8" ___________________________________________ 17-20001/2" as C2296-3 _________________________________ 17-19995/8" as C2296-1 _________________________________ 17-19983/4" ___________________________________________ 17-19977/8" ___________________________________________ 17-1996

Rear Wire Wheel Hub PullerFor any Jaguar with spline-drive wire wheels, this is the proper toolto safely and properly remove the rear hubs without damage. Savetime and eliminate frustration with the right tools. A faithful replica ofthe original factory part. _____________________________ 17-J7

Mr. Moly™ Additives

Red Line LubricantsRecognized by many as the finest synthetic lubricants available.We’ve raced and won using Red Line products and can highlyrecommend their use. Red line oils provide a significant reductionin wear over other commercially available lubricants. Reducedoperating temperatures prolong mechanical life. Safe for use in allapplications. Non-detergent motor oil not recommended for dailystreet use.

40W Racing Motor Oil ________________________ LE-9002

50W Racing Motor Oil ________________________ LE-9003

10W40 Racing Motor Oil ______________________ LE-9030

75W90 Gear Oil ____________________________ LE-97590

Tools, Lubricants, Etc.


Rear

Sus

pens

ion/

Diffe

rent

ial

29

1. Mounting Bush, 2 required _________________ JA-CCC68752. Differential Strut, to 644282 (mid '91), 2 required JA-CBC87013. Differential Strut, 644283-on, 2 required _______ JA-CCC37894. Wishbone Tie Assembly ________________ JA-MMB2850AA5. Pendulum Bush, Top, 2 required ___________ JA-CAC7760-16. Pendulum Bush, Bottom, 2 required __________ JA-CAC47137. Buffer, wishbone tie assy (not shown), 2 req'd JA-MNA2885AA8. Buffer, wishbone rear compliance, 2 required JA-MMB2881AA9. Bump Stop, (not shown), 2 required _______ JA-MNA3750BA10. Upper Mount Isolator, 2 required __________ JA-CBC2257-6011. Upper Strut Isolator, 2 required ___________ JA-CAC9493-5012. Lower Strut Isolator, 2 required ___________ JA-CAC9494-6513. Gaiter for strut, self leveling, 2 required________ JA-CAC968014. Gaiter for strut, non-leveling, 2 required _______ JA-CBC188615. Strut, non-leveling, to VIN 696458, 2 required __ JA-CCC692316. Strut, non-leveling, VIN 696459-on, 2 req'd _ JA-MNA3540AA

XJ-40 Conversion Kit:Self-Leveling to Conventional ShocksJaguar had so many problems with the self leveling rearsuspension that it developed a kit to fit conventional shocks.The factory kit includes new shocks, springs and all neces-sary hardware. We also have a less expensive kit made byshock manufacturer KYB. It includes new shocks andhardware but not springs. We recommend professionalinstallation. A spring compressor is required. (Converts allXJ-40 with self-leveling rear suspension.)Factory Kit ________________________ JA-JLM11698KYB Kit ___________________________ 14-1400KYB

30

15-21

13

12

11

10

23

14

15-21

24-27

12, 3

4

5

6

8

17. Strut, self-leveling, to VIN 696458, 2 required ___ JA-CBC889218. Strut, self-leveling, VIN 696459-on, 2 req'd __ JA-MMD3440AA19. Strut, X300, non supercharged, OE _______ JA-MNA3540AD20. Strut, X300, non supercharged, Aftermarket JA-MNA3540AD/X21. Strut, X300, supercharged_______________ JA-MNA3540CD(Also see page 258 for aftermarket shocks.)22. Mineral oil for self-leveling struts, liter, as required JA-JLM988623. Spring Insulator, 2 required ______________ JA-MMD3565AA24. Rear Spring Pair, non-leveling, to VIN 696458 ___ JA-JLM65725. Rear Spring Pair, non-leveling, VIN 696459-on JA-JLM1142226. Rear Spring Pair, self-leveling, to VIN 696458 ___ JA-JLM74727. Rear Spring Pair, self-leveling, VIN 696459-on _ JA-JLM1142328. Guide Bush, upgaded polyurethane, non-leveling JA-CBC293329. Ride level sensor, self leveling only___________ JA-DBC676830. Universal Joint, half shaft, 4 req'd, XJ-40, X300 _ JA-JLM1388Note: Unless specified, items on this page are XJ-40 only.

28

XJ-40 Rear Suspension




Rear Suspension

I. R. S. Half Shaft Components1. Joint Cover, inner with hole, 2 required ____________ C288432. Joint Cover, Inner, no hole, 2 required ____________ C236153. Joint Cover, outer with hole, 2 required ____________ C288444. Joint Cover, outer, no hole, 2 required ____________ C23616Note: Series I E-Type use four of these covers for the outboardU-joints only. Early 3.8-liter E-Types did not use joint covers.5. Camber Adjusting Shim, as required _______________C16621Halfshaft Universal Joints, four required:6. All pre-XJ-40; XJ-S to�188105 (inboard brakes)____ 12-119487. All XJ-40, XJ-S from 188106 (outboard rear brakes),

1995-1997 "X300" XJ-6/12, XJ-8, XK-8________ JA-JLM13888. Stub Axle Washer, 2 required ___________________ C249239. Stub Axle Nut, 2 required ________________ JA-ND612041J10. Joint Cover Plug, 2 required _________________ JA-338023J

E-Type Series I & II, Early XJ-S Rear Anti-Sway Bar1. Link Bush, E-Type only, 4 required ________________C10940

Sway Bar Mount Bush:

2. E-Type Ser. I and II ___________________________ 14-2014

3. XJ-S (early cars only) ________________________ C44931/2

4. Sway Bar Mount Bracket, all _____________ JA-MNA3501AA

5. Link Assembly, early XJ-S only ___________________C42907

6. Link Assembly, E-Types ________________________C20765

I. R. S. Unit Mounts, Bump Stop1. I.R.S. Mount, MK 10, 420G _____________________ C18104

2. I.R.S. Mount, XJ-6 thru 1987, XJ-S Coupe, XJ-12 JA-CAC3067

3. I.R.S. Mount, XJ-S Convertible ______________ JA-CBC5737

4. I.R.S. Mount, 420, 3.8S, all E-Types, OE Metalastik __ C17198

5. I.R.S. Mount, 420, 3.8S, all E-Types, Aftermarket____ C17198*

6. Packing Piece, E-Types only (8 required) __________ C17228

7. Bump Stop, all pre-XJ-40 with I.R.S. _______________C40158

1-5

67 I.R.S. Springs & Components

Springs (four required)1. Series I & II E-Type ___________________________ 13-02022. E-Type Series III _____________________________ 13-02123. 3.8S and 420 ________________________________ C231674. MK X/420G __________________________________C212805. XJ-6 & XJ-12 ________________________________ C299786. XJ-S Coupe to VIN 184574 _____________________ C39692Colletts, Bottom of Springs:7. E-Type Series I and Series II, 3.8S, 420, MK X,

420G (8 required) ____________________________ JA-86878. E-Type Series III, XJ-6, XJ-12, XJ-S (8 req.)_________C37273Retainer/Seat:9. E-Type, All ___________________________________C3727110. XJ-S, XJ-6 Series I and II, XJ-12 Series I, XJ-S H.E., XJ-6

Series III, 3.8S, 420, 420G, MK X, XJ-12 Series III ____C1982111. Packing Ring, Top of Coil, E-Type Series I _________ C1902712. Dust Shield (This part may have been discarded if aftermarket

shocks have been installed.) ____________________ JA-8688

1-6

9, 10

7, 8

11

1

1

6

4

2, 3

2

13

4

5

6

6, 7

10

9

8

5

12


Rear

Sus

pens

ion/

Diffe

rent

ial

Driveshaft Components1. Driveshaft bolt, Early “D” Head (Cars with JA-46 U-joint) C3308

2. Driveshaft bolt, Later “Hex” Head _________________C19827

3. Driveshaft Mount, Earlier XJ, MK X, 420G _________ C36791

4. Bushing for Driveshaft Mount, Earlier XJ, MK X,420G, 4 required _________________________ JA-CBC1448

5. Driveshaft Boot, E-Type, Sedan, XJ __________ JA-JLM1543

Driveshaft Universal Joints:

6. 2-3/4"*: XK-120, 140 & 150, MK VII, VIII & IX, MK I,early MK II, very early 3.8 E-Type __________________ JA-46

7. 3"*: later 3.8 E-Type & MK II, 4.2 E-Type, V-12 E-Type3.8S, 420, 420G, MK X, XJ-6, XJ-S 5.3 ________ JA-JLM823

8. XJ-S 6.0 V-12 __________________________ JA-JLM11718

9. XJ-S 4.0-Liter 6-cylinder ____________________ JA-JLM269

10. Center Support Bearing, later Series II XJ-6 and XJ-12 and allSeries III XJ-6 ___________________________ JA-EBC9040

11. Bearing only, Early Center Support Assembly _______ JA-250Note: JA-250 fits Series I XJ-6, Series II XJ-6 4-door to 2T.56342;Series II XJ-6 2-door to 2J.50524; Series I XJ-12; Series II XJ-12 4-door to 2R.57492; Series II XJ-12 2-door to 2G.51201.

Note:* Measured across U-joint without caps.

Driveshaft Center Bearing, Early SedansMK II, MK VII, VIII, IX with automatic transmission.

1. Bushings, 2 per car ____________________________C25389

2. Bearing, 1 per car _____________________________ JA-250

Ring & Pinion SetsFor Salisbury axles or I.R.S. differentials. We also sell completerebuilt differentials. Other ratios available.Ratio __________________________________________ Part No.3.07:1 _________________________________________ 13-30013.31:1 _________________________________________ 13-30023.54:1 _________________________________________ 13-30034.10:1 _________________________________________ 13-3004

4.55:1 _________________________________________ 13-3005

2

1

1

12

XJ-40, X-300, XJ-8, XK-8 Driveshaft Components(XJ-40 = XJ-6 1988 to 1994; X-300 = XJ-6/XJ-12/XJR 1995 to 1997)

Early non-Jurid Type, XJ-40 to VIN 538477:Note: This type has no rubber “donut” between front & rearshafts.

1. Universal Joint, 3 required ___________________ JA-JLM823

2. Gaiter (rubber boot) _______________________ JA-JLM1543

3. Rings for Gaiter, 2 required _________________ JA-JLM1544

4. Rubber Clip for Gaiter, 1 required ____________ JA-JLM1545

5. Center Bearing __________________________ JA-EBC9040

Later Jurid Type, XJ-40 VIN 538478-on and all X-300:

1. Universal Joints:538478 to 594575 (to end of 1989), 2 required ___ JA-JLM823XJ-40 1990-1994, 2 required ________________ JA-JLM2302X-300 (1995-1997 XJ-6) __________________ JA-JLM11718

2. Gaiter (rubber boot), all ____________________ JA-JLM1543

3. Rings for Gaiter, 2 required _________________ JA-JLM1544

4. Rubber Clip for Gaiter, 1 required ____________ JA-JLM1545Rings and Clip not required after 1989 (594575)

5. Center Bearing, XJ-40 538477 to 594575, all X-300JA-EBC9040

Center Bearing replacement for 594576 to 646827 requiresreplacement of complete driveshaft assembly JA-NBB5800AA

Center Bearing, 646828-on _________________ JA-EBC9040

6. Rubber “Donut” Flex Coupling:

538477 to 594575 (end of 1989) _____________ JA-CAC7576

7. 1990-on XJ-40, all X-300, XJ-8, XK-8 _________ JA-CBC8996

123 4

5

1

6, 7

6-9

6-9

6-9

3

45

1011

Driveline

rear axle/suspension - seekpartfile.seekpart.com/keywordpdf/2011/3/22/201132284812410.pdfaxle...

Documents