rebecca fold over clutch pattern instructions
TRANSCRIPT
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 1
INTRODUCING
REBECCA A Fold Over Clutch with a Zippered Top and Magnet Snap Closure
andreagaildesigns
Featuring a full exterior back zippered pocket, fold over zippered top with a magnet closure
and an adjustable crossbody strap.
Finished measurements 13.5” W at the top, 11.5” W at bottom, 8” H folded over, 3.5” D
Skill Level Advanced Beginner
Instructions are written for fabric, cork or vinyl construction but may be used
with 2—2.5 oz leather if it can be turned through a 7 inch opening.
The Rebecca fold-over clutch is the perfect size for everyday use or a night on the town. You’ll love the
stylish fold-over zippered closure, plus the accessible back zippered pocket. Inside is super roomy due to
top opening, and you’ll find an ample zippered pocket plus divided slip pocket. The pleats finish the bag
and make it even roomier! The use of minimal hardware is a bonus! She’s a relatively quick sew and if you
purchase the add-on non-slip template, even quicker!
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 2
.
PLEASE READ THROUGH INSTRUCTIONS BEFORE BEGINNING
There is one MAIN PATTERN PIECE for the front and lining pieces. The back is made from 2 pieces
joined with the outside zipper pocket then cut to the shape with the MAIN PATTERN PIECE. You will al-
so need to cut pieces for the pockets and handle strap. There are pattern pieces for these, (no pattern
piece is given for strap) measurements to cut are given as well.
The measurements include a generous cut to be sure to accommodate the MAIN PATTERN PIECE.
If you prefer, you may cut the pieces a bit smaller.
Please feel free to make and sell as many bags as you wish from this pattern. If you plan to teach this
pattern, each student needs to own their own copy. The pattern is designed by andrea gail designs and
may not be claimed as your own.
What You’ll Need 3
Piece Map 4
Cutting & Prep Instructions 5
Cutting Chart 6
Crossbody Strap & Connector 7
Exterior Back Zipper Assembly 8
Front Magnet Assembly 9
Top Zipper Closure Front/Back Assembly 9
Interior Slip Pocket 10
Interior Zipper Pocket 11
Putting it all Together 12
Inspiration photos 15
Pattern Pieces 19
WHATS’ INSIDE?
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 3
To make this pattern you will need:
Fabric for exterior Front ½ yard
Contrast fabric for exterior back ½ yard
Lining fabric ¾ yard
2 yd. approx. SF101 or Wovenfuse fusible interfacing
2-#5 zippers; one is 12” for the back, one is 16” for the top. These will be a bit longer than needed, ex-
cess will be trimmed.
1-#3 Zipper for interior pocket 9”. This is a bit longer than needed, excess will be trimmed.
1 magnet snap closure
2-D rings ½”, 3/4” or 1” your preference
2-swivel hooks ½”, 3/4” or 1” your preference
1 ½”, 3/4” or 1” adjustable wide mouth slider
Notions/Tools
Thread
Clips or pins
Marker
Rotary cutter and ruler
1/4” double sided tape (DST)
1/2'’ DST (1/4” can be used, it will take twice as much)
Sewing machine
Scissors
Seam allowance is 3/8”—Lining seam allowance 5/8” (unless otherwise directed).
Common use abbreviations
• RST Right sides together
• RSU Right side up
• BLT Bacon, lettuce, tomato
• WST Wrong sides together
• SA Seam allowance
• DST Double sided tape
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 4
Don’t forget to post pics on the Facebook and Instagram pages. We all love inspiration and we love to see
your creative makes. You are always welcome to post photos and questions or ask for assistance on the
facebook page.
https://www.facebook.com/andreagaildesigns https://www.instagram.com/andreagaildesigns/ https://www.pinterest.com/andreajoiner/
EXTERIOR LOWER BACK
EXTERIOR UPPER BACK
EXTERIOR UPPER BACK
EXTERIOR FRONT
Piece Map
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 5
CUTTING & PREP INSTRUCTIONS Use cut list on the next page
For EXTERIOR BACK cut 1 panel measuring 15.5”W x 6.5”H;, this will be the upper exterior; Cut 1 panel
15.5”W x 10.5”H, this will be the lower exterior. These will need to be fused with interfacing. This piece
will be trimmed to the proper shape with the MAIN PATTERN PIECE after the zipper has been attached.
From LINING cut 1 panel from the MAIN PATTERN PIECE this is for the back of the Exterior Zipper pocket.
First cut 1 piece of fabric 15.5”x16.5”. This piece will need the fusible interfacing applied, then cut out the
final piece with the MAIN PATTERN PIECE.
For STRAP Cut 2—2” strip by 54” if you are making a strap with two different fabrics, one on each side. If
making straps with one fabric cut 1—4”x54”. This is for 1” strap. If you are making a cork strap or with non-
fraying fabric, cut 1—1” strip 54”. This is for ½” strap. If you are making 3/4” straps cut 3” by 54” with non
fraying fabric. Cut 1—2” strap by 54” for second half of strap with contrast fabric. This is for 1” strap.
Cut 2—4”x2” strips for zipper tabs on the back-exterior zipper pocket. These will be trimmed to size.
Cut 1—2”x2” piece for top zipper end tab for the zip across the top.
From LINING FABRIC Cut 2 pieces of fabric 15.5”x16.5”; fuse these with interfacing, then cut out the shape
with the MAIN PATTERN PIECE
From LINING FABRIC cut 2—8”x7” for zipper pocket, add fusible interfacing. Cut 2—6”x11” for divided patch
pocket, add fusible interfacing.
***IMPORTANT NOTE: If you are not using the no-slip grip template, rather
you are using the MAIN PATTERN PIECE included in this pattern, you will use
this pattern to cut out the EXTERIOR BACK after the zipper is added. ***
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 6
CUTTING CHART
Pattern Piece All measurements LxW
Exterior Lining Interfacing Notes
A Exterior Front Cut one from contrast fabric This will be cut using MAIN PATTERN PIECE
1—15.5”x16.5” 1—15.5”x16.5” IF using cork, or vinyl —no interfacing
A Lining Main these will be cut using the MAIN PATTERN PIECE
3—15.5”x16” 3—15.5”x16”
B Exterior Upper Back Cut 1 from exterior fabric and 1 interfacing
1—15.6 “x 6.5” 1—15.6 “x 6.5”
C Exterior Lower Back Cut one from exterior and one from lining.
1—15.5”x10.5” 1—15.5”x10.5” 2—15.5”x10.5”
D Interior Zipper Pocket 2—8”x7” 2—8”x7”
E Interior Slip Pocket 2—6”x11” 2—6”x11”
Zipper Tabs Exterior 2—4”x2”
Zipper Tab Top OR Cork or non-fray fabric
1—2”x2” 1—1”x2”
Interior Zipper window facing 2”X8”
Strap 1 from each con-trasting piece 1” option
2—2”x54” 2—2”x54”
Strap with non-fraying cork or fabric ½” option
1—1”x54”
Strap connectors for 1” strap 2—4”x3”
Strap connector for ½” strap 2- - 1”x3”
If you choose to use the add-on no-slip grip template here is a video that shows how to use it.
https://www.youtube.com/watch?v=lx9DQ0maHzg
The intent of the template is to have easier more precise cutting on the curves of this pattern
because the no-slip grip won’t shift on the fabric and individual preferred cutting angles are
accommodated.
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 7
I like to make straps first to get them done, if you prefer, you can sew them last.
There are 2 options for STRAP First is 1” strap with contrasting front and back and second is ½” strap made with
cork or non-fraying edge fabric. You could also make 3/4” straps with non-fraying fabric; use same directions as
1/2”. Cut 3” wide X 54” long.
Option #1: 1” strap
Step 1. Interface both 2”x 54” strap pieces; draw a line down
the center of each piece. Place double sided tape (DST) next
to both sides of the line. Divide the tape so that each end
has a separate piece 3” long from both ends. Stick edges to
the center (leave backing on the 3” piece at the ends) to
make a 1” wide strip. Repeat this step for another contrasting
strap piece. Cut one piece 2” shorter, I like to chose which
side with be the “top or pretty side”, the other side will be the
shorter piece.
Step 2 Open the ends of the straps with the 3” DST backing
still adhered, place strap ends RST sew across the ends mak-
ing sure that the strips are not twisted. This will give the ends a finished
edge. Remove backing from 3”ends stick raw edges to the middle. Place
the two strap sections RST making sure that the ends have equal amount
of “pretty side” extending.
Step 3 Top stitch 1/8” from both edges.
Step 4 On one finished end, slip through the center of the slide buckle,
fold over 1.5”and stitch or rivet in place.
Step 5 On the other end slip one of the swivel hooks onto the
strap piece.
Step 6 Take that same end, slide it through both sides of the slide
buckle as shown.
Step 7 Then add the second swivel hook to that end, fold over
1.5” and stitch or rivet in place.
Option #2. ½” strap using cork or non-fraying edge.
Fold 1”x 54” in half longways. Top stitch each edge 1/8”. Repeat steps 4-7 same as option #1.
FOR CONNECTORS: If you are using 1”D-rings you’ll need to cut 2- 4”x3” pieces. Draw a line marking the center on
the 4" pieces and then fold each long edge to the center line to create 1" x 3" connector piece.
Top stitch 1/8” both edges. Add D-ring fold in half so that the piece is 1”x1.5”.
If using ½” D-rings cut 2 pieces of cork or non-fraying fabric 1”x3”. Fold in half, top stitch 1/8” both edges, add
D-ring fold in half so that the piece measures ½”x1.5”
Your strap and connectors are complete. Set aside.
4
2 2
3
5-7
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 8
EXTERIOR BACK ASSEMBLY WITH EXTERIOR ZIPPER POCKET
Use zipper tabs 2—4” long X 2” wide. These will be trimmed
to proper size. You will also use lower exterior pocket lining.
You will also need pieces C—EXTERIOR LOWER BACK and lin-
ing; D—EXTERIOR UPPER BACK
Step 1 Add zipper pull to the 12” zipper if you are using zipper
tape by the yard. Trim zipper to measure 10”. Place zipper tabs
on both ends of zipper. Use the 2—4”x2” pieces, placing the 2”
edge along the zipper ends. Sew ends.
Step 2 Take the 2—15.5”x10.5” pieces and sandwich the 15.5”
side with the bottom zipper edge, and lining piece center the
zipper, having the zipper tabs extending past the edges of the
15.5” bottom back section. Stitch the top edge of lower back
section with the zipper sandwiched in between. This is the
bottom section of the back.
IMPORTANT: If you are using a directional design fabric, make sure the zipper
edge is at the top of the design.
Open the pieces up, WST, press and top stitch 1/8” if desired. You will top stich
only the lower zipper pocket here. Top section will be top stitched after it is
sewn to the back pocket lining.
Step 3 Take the 15.5”x6.5” pieces and add it to the top of the zipper.
If you are using a directional design fabric, the zipper edge should be at
the top of the design. This is to make sure that when the top is folded over,
the design will be “right side-up”.
Step 4 Take the lining piece, 15.5”x16.5” place it RSU on your surface, place
MAIN PATTERN PIECE on top of this, it is cut to
shape. Find the zipper line on the MAIN PATTERN
PIECE, mark on lining; place the EXTERIOR BACK
with zipper pocket on top matching the zipper
placement line. Fold down the top section of the
completed EXTERIOR BACK with zipper and sew
across the zipper seam as shown. Fold back, top-
stitch.
SEE VIDEO FOR INSTRUCTIONS:
https://www.youtube.com/watch?v=-T1KBysZ2JE
1
2
4 4
3
3
Piece B
Piece C
Piece C lining
Exterior back lining
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 9
For this step you will need the main piece A FRONT cut out with the template
Step 1 Make sure that the 2—15.5” x 16” pieces with medium interfacing fused
are cut to the correct shape using the template.
Step 2 Mark the placement for the magnets.
Step 3 Add the male piece to the top edge
Step 4 Add the female piece to the place near the zipper placement line on the
mark previously made. Press prongs outward.
Step 5 I like to add a scrap of fabric and a piece of duct tape to the back of the prongs to help make sure
they can’t be felt through the lining on the inside of the bag.
TOP ZIPPER CLOSURE FRONT/BACK ASSEMBLY
This step will need the exterior front with magnet added and the
exterior lower back with pocket assembled.
Step 1 Place pulls on the zipper and add the zipper tab to the right end
of the zipper in step 2.
Step 2 Take the 2”x2” piece, fold it in half, then fold edges inward.
Sandwich the end of the zipper tape in the zipper tab and sew across
the end. If you are using cork or a non fraying fabric, you won’t need
to fold edges to center. This may be too bulky. You will need 2’x1’
piece of fabric folded over to encase the end of the zipper. Trim edg-
es of zipper tab even with zipper tape. Topstitch.
Step 3 Starting on RIGHT top edge of FRONT EXTERIOR (front exterior
has no exterior zipper pocket) piece, right side facing you, place the
top zipper tab edge ¾” from the side edge of the fabric. Make sure
the right side of zipper tape is facing right side of the FRONT EXTERIOR
6
2
3
6
Step 6 Turn the piece over so that the back of the exterior
back pocket piece is showing and trim excess fabric so that it is
the correct pattern shape. Baste all layers together with scant
1/8” SA. If using heavier fabric, excess fabric at the top can be
trimmed off.
Back Exterior piece with the zipper pocket should now be the
correct shape.
FRONT MAGNET ASSEMBLY
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 10
piece. Working toward the LEFT edge of the FRONT EXTERIOR
piece, (the side with the magnet installed) clip zipper to the edge of
the fabric RST.
Step 4 When you are about 2” from the LEFT edge, draw a line
across the end of the zipper ¾ inch from side edge of the FRONT
EXTERIOR piece. Fold the zipper on the line wrong side of zipper
against wrong side of zipper, then make another fold on the zipper
so that the end folds out away from the seam allowance as shown.
Place a pin in that folded section. Sew it in place.
Step 5 Sew the other edge of the zipper, using the same technique.
INTERIOR SLIP POCKET
For this step you will need lining slip pocket E that has been inter-
faced. And you will need a strip of fabric or non-fraying fabric to
enclose the raw edge at the top of the pocket.
Step 1 Take the 2—6”x11” pieces fused with lightweight interfac-
ing, sew around 2—6” sides and one 11” edge with 3/8”SA. Trim
corners, turn, press.
Step 2
If you are using cork cut a piece ¾”x 11”, fold in half, sew to the
top of the unfinished edge of the pocket encasing the raw
edge with a topstitch. You will need to trim the cork piece
so that the ends are even with the pocket edge.
If you are using a piece of fabric that will match one of the exte-
rior fabric, cut a piece 2”x11”. Fold this in half longways,
fold short ends in to encase the raw end edge inside the
facing strip, sew long raw edges to the pocket piece raw
edge. Turn the facing strip so that the fold is on the front,
top stich in place.
Step 3 Press. Make sure to press in half to have a line to follow
when stitching the divided patch pocket to the lining piece.
Step 4 Take one of the lining pieces that has been fused with medi-
um weight interfacing and place the pocket, centered, on the zip-
per placement line found on the MAIN PATTERN PIECE.
Stitch around the edges and up the middle to divide the pocket as
shown.
4
5
4
4
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 11
INTERIOR ZIPPER POCKET
For this step you will need 2- Zipper pocket pieces D interfaced and
the 2”x8” strip of fusible interfacing for zipper window
Step 1 Using piece of medium weight fusible interfacing 2”x 8”. Draw
2—7” lines 3/8” apart down the center of the long edge on the wrong
(glue) side of the interfacing.
Step 2 Center the right side of the interfacing against right side of 2nd
lining piece having the top edge of the interfacing
strip along the zipper placement line on the MAIN
PATTERN PIECE.
Step 3 Sew along both parallel lines you’ve drawn.
Step 4 Slice with your cutter or cut with scissors, be-
tween the two sewn lines to ½” from end of the in-
terfacing piece. Snip all 4 corners from the center
slice to each corner.
Step 5 Turn the interfacing piece to the wrong side and fuse as shown.
Step 6 Add DST to both long edges of the zipper win-
dow on the wrong side. If you prefer, add DST to the
edges of the right side of the zipper tape to make it
easier to center in zipper window.
Step 7 Place zipper with the pull on the left edge,
face down on the exposed zipper tape.
Step 8 Then add DST to both long edges of the
wrong side of the zipper, place 8” edge of zipper
pocket piece on the exposed lower edge of the zipper. with the WSU and
the pocket piece covering the zipper and extending towards the top
You will remove the DST one side at a time.
Step 9 On the outside, top-stitch the lower edge of the zipper. Fold this
piece down to the inside and crease before adding the top piece.
Step 10 On the wrong side of the lining piece, place the second 8”edge of
the zipper pocket piece to the top zipper edge along the exposed edge of the DST.
Step 11 On outside, top-stich top edge of zip-
per in place and the two edges.
SEE NOTE ON NEXT PAGE
Step 12 Finally, on the back side, stitch all 3
edges of the pocket closed as shown, trim so
the bottom edge is even.
5
1&2
5
10
6
12
8
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 12
PUTTING IT ALL TOGETHER
For this step you will need both exterior pieces and both lining pieces
that have been assembled with pockets.
Step 1 Take lining pieces and exterior pieces to be joined. Sandwich
lining piece with the zipper pocket to the EXTERIOR BACK across the
top zipper. Pin or clip in place and sew the zipper edge with precise
3/8” SA. Trim seam to reduce bulk.
Step 2 Pin or clip the second lining piece to the EXTERIOR FRONT piece,
right sides together sew the zipper edge with precise 3/8” SA. Trim
seam to reduce bulk.
Step 3 Press the lining and the exterior along the zipper edge (take care
if you are using cork—you’ll need a pressing cloth and less heat).
Top stitch 1/8” along each zipper side. If you prefer, topstitch the
exterior zipper sides only, not lining.
Step 4 Place connectors where the strap markers show on the tem-
plate, with the D-rings raw edges outward and D-ring toward the inside
of the bag. Baste edges.
Step 5 Open top zipper at least half way. Place exterior front and back
together RST and lining front and back RST.
Sew around the lining section and the exterior section. Start sewing 2”
from dart in lining (back stitch), sew around the exterior portion (don’t
worry about darts, they will be sewn in next step) Stopping 2” from
dart in lining so that there is an unsewn 7” space that will be used for
turning the bag right side out.
When sewing the lining side use 5/8” SA; when sewing the exterior
side use 3/8” SA. Taper the SA when sewing the lining side, going from
5/8” SA on lining portion to 3/8” SA on exterior portion. Back stitch
over the area where the connectors are in the seam.
Zipper
D-Ring Placement
1 & 2
4
5
Stop Seam Start Seam
NOTE: AS AN ALTERNATE TURN RIGHT SIDE OUT METHOD:
IF YOU PREFER: To turn through the pocket and not having a visible closure seam on the lining, leave the
bottom edge of the interior zipper pocket unsewn. When it is time to turn the bag right side out, you can
do this through the lining first, then through the pocket, then sew up the bottom edge of the pocket.
Still leave a 7 inch opening in the lining, turn right side out through the lining, then pull the lining through the
lower edge of zipper pocket, sew the lining closed, then sew the bottom edge of the zipper pocket. I like to
turn it right side out, then check to be sure all seams are correct and it looks good, then sew up the bottom
zipper pocket edge. Be sure to open the zipper on the pocket FIRST in order to turn through this opening.
Leave 7” unsewn
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 13
Trim SA all around to reduce bulk.
Step 6 Sew Darts. For each of the 4 darts, reach inside from
the unsewn space in the lining left for turning, to make sure
that the dart seams line up. Sew 5/8” SA on lining side, sew
3/8” SA on exterior side.
Step 7 Turn the bag right side out through the seam left un-
sewn on the lining. Check all seams and zippers, make sure
everything opens as it should and it all looks good, then sew
the lining seam shut.
Attach the strap to the D-rings.
CONGRATULATIONS You’re done!
Enjoy your new bag.
Darts
6
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 14
Don’t forget to post pics on the Facebook and Instagram pages. We all love inspiration and we love to see
your creative makes.
https://www.facebook.com/andreagaildesigns
https://www.instagram.com/andreagaildesigns/
https://www.pinterest.com/andreajoiner/
www.andreagaildesigns.com
You are always welcome to post photos and questions or ask for assistance on the Face-
book group.
PATTERN SUPPORT Facebook Group
https://www.facebook.com/groups/322415978792706
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 15
Inspiration by some of the best bag makers!
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 16
Inspiration by some of the best bag makers!
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 17
Inspiration by some of the best bagmakers!
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 18
Inspiration by some of the best bagmakers!
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 19
Inspiration by some of the best bagmakers!
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 20
1 Inch Test
Square
REBECCA
MAIN PATTERN PIECE
Exterior Front and Back FOLD
***IMPORTANT NOTE: If you are not using the no-
slip grip template rather you are using the MAIN
PATTERN PIECE included here, you will use the
MAIN PATTERN PIECE to cut out the EXTERIOR
BACK after the zipper is added.
www.andreagaildesigns.com
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 21
1 inch test
square
FOLD
Snap
Snap Zipper Placement Exterior Back
Strap
www.andreagaildesigns.com
REBECCA
MAIN PATTERN PIECE
Exterior Front & Back
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 22
1 Inch Test
Square
A-1 FO
LD
REBECCA
Exterior FRONT
Exterior BACK & LINING
Cut 1 on FOLD Exterior Fabric
ONE is a piece to be cut with the MAIN PATTERN PIECE
which will be the FRONT the magnet sanp is attached to the FRONT
Cut THREE on FOLD interfacing, then cut to shape using the
MAIN PATTERN PIECE
Cut THREE for lining , then these 3 will be cut to shape using the
MAIN PATTERN PIECE
15.5 X 16.5
www.andreagaildesigns.com
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 23
1 Inch Test
Square
A-2
FOLD
REBECCA
www.andreagaildesigns.com
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 24
1 Inch Test
Square
FOLD
B
RE
BE
CC
A
Exterio
r Up
pe
r BA
CK
Cu
t 1 o
n FO
LD Exterio
r Fabric
Cu
t 1 o
n FO
LD in
terfacing
15
.5 X
6.5
ww
w.an
dre
agailde
signs.co
m
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 25
1 Inch Test
Square
C-1
FOLD
RE
BE
CC
A
Exterio
r Low
er B
AC
K
Cu
t on
e fro
m exterio
r 15
.5”x1
0.5
” and
and
on
e-15
.5”x1
0.5
” linin
g
INTER
FAC
E as need
ed.
ww
w.an
dre
agailde
signs.co
m
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 26
1 Inch Test
Square
C-2
FOLD
RE
BE
CC
A
Exterio
r Low
er B
AC
K
ww
w.an
dre
agailde
signs.co
m
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 27
1 Inch Test
Square
RE
BE
CC
A
Inte
rior Zip
pe
r Po
cket
Cu
t 2 lin
ing an
d 2
light in
terfacing
8”W
x7” H
ww
w.an
dre
agailde
signs.co
m
D
REBECCA Fold Over Clutch Pattern andrea gail designs Copyright 2020 Page 28
1 Inch Test
Square
FOLD
RE
BE
CC
A
SlipP
ocket
Cu
t 2 lin
ing o
n fo
ld lin
ing
Cu
t 2 ligh
t interfacin
g on
fold
6”H
x 11
”W
ww
w.an
dre
agailde
signs.co
m
E