recommendation: table 17–1 - iapmo group report on comments/2009 unifor… · · 2011-01-05ansi...
TRANSCRIPT
UMC 2009 – August 2007 ROP
SUBMITTER:
Add new text as follows:
Table 17–1__________________________________________________________________________________________Standard Number Standard Title [UMC Reference]__________________________________________________________________________________________ANSI LC4–2007 Press-Connect Copper and Copper Alloy Fittings
For use in Fuel Gas Distribution Systems
This proposed code change will add the nationally recognized consensus standard ANSI LC4–2007 to the list of recognized standards.
(LC4–2007 IS attached)
SUBSTANTIATION:
RECOMMENDATION:
UMC 2009 Table 17–1
Accept as Submitted
Andrew Granzow
106-
Viega LLC
TOTAL ELIGIBLE TO VOTE: 24
VOTING RESULTS: AFFIRMATIVE: 22, NOT RETURNED: 2 T. Nothaft, D. Bixby
COMMITTEE ACTION:
Item #
SUBMITTER:
Revise table as follows:
(See attached Table 17–1 Standards for Equipment and Materials on pages 169–1 through 169–8)
Editorial changes to Table 17–1 in UMC
SUBSTANTIATION:
RECOMMENDATION:
UMC 2009 Table 17–1
Based on committee action taken on Item 111.
Reject
John Taecker
107-
UMC Standards Task Group
TOTAL ELIGIBLE TO VOTE: 24
VOTING RESULTS: AFFIRMATIVE: 22, NOT RETURNED: 2 T. Nothaft, D. Bixby
COMMITTEE ACTION:
COMMITTEE STATEMENT:
Item #
169
Standard Number Standard Title [UMC References]
ACCA Manual D Residential Duct Systems
ACCA Manual J Residential Load Calculations
ACCA Manual N Commercial Load Calculation
ACCA Manual Q Low Pressure Low Velocity Duct Systems Design
ANSI A13.1-96 Scheme for the Identification of Piping Systems
ANSI A21.10-03 Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1200 mm), for Water and Other Liquids (same as AWWA C110)
ANSI A21.51-02 Ductile-Iron Pipe, Centrifugally Cast, for Water (same as AWWA C151)
ANSI B1.20.1-1983 (R2001) Pipe Threads, General Purpose, Inch (Except Dryseal) (replaced by ASME B1.20.1-98)
ANSI B1.20.3-1976 (R2003) Dryseal Pipe Threads (Inch)
ASME B31.5-2001 Refrigeration Piping
ANSI Z21.1-2000 Household Gas Cooking AppliancesAddendum Z21.1a-2003
ANSI Z21.5.1-2002 Gas Clothes Dryers - Volume I, Type IANSI Z21.5.1a-2003Addenda Z21.5.1a-2002
ANSI Z21.5.2-2001 Gas Clothes Dryers - Volume II, Type 2CSA 7.2-2001
ANSI Z21.5.2a-2003Addenda Z21.5.2a-2003
ANSI Z21.8-(R2002) Installation of Domestic Gas Conversion Burners [UMC 906.0]
ANSI Z21.10.1-2004 CSA 4.1a02 Gas Water Heaters, Volume I, Water Heaters with Input Ratings of 75,000 Btu per Hour or Less
ANSI Z21.10.3-2004 Gas Water Heaters, Volume III, Water Heaters with Input Ratings Above 75,000 Btu per Hour, Circulating and Instantaneous Water Heaters
ANSI Z21.11.2- 2002 Gas-Fired Unvented Room Heaters, Volume IIAddenda Z21.11.2a-2003
ANSI Z21.12-1990 (R2000) Draft HoodsAddenda Z21.12a-1993 (R2000)Addenda Z21.12b-1994 (R2000)
ANSI Z21.13-2004 CSA 4.9a02 Gas-Fired Low Pressure Steam and Hot Water Boilers
ANSI Z21.15-1997 (R2003) Valves for Appliances, Appliance Connector Valves and Hose End Valves, Manually Addenda Z21.15a-2001 (R2003) Operated Gas
CHAPTER 17
TABLE 17-1
Standards for Equipment and Materials
Note: This Chapter has been revised and reformatted in its entirety.
No arrows or side bars have been used to signify changes.
Item #107
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
ANSI Z21.17-1998 CSA 2.7-M98 Installation of Domestic Gas Conversion Burners
ANSI Z21.18-2000 Gas Appliance Pressure RegulatorsAddenda Z21.18a-2001
ANSI Z21.19-2002 Refrigerators Using Gas Fuel
ANSI Z21.20-2000 Automatic Gas Ignition Systems and ComponentsAddenda Z21.20a-2000Addenda Z21.20b-2001
ANSI Z21.21-2000 Automatic Valves for Gas AppliancesAddenda Z21.21a-2001
ANSI Z21.22-1999 (R2003) Relief Valves for Hot Water Supply SystemsCSA 4.4-00
Addenda Z21.22a-2000Addenda Z21.22b-2001
ANSI Z21.23-2000 Gas Appliance ThermostatsAddenda Z21.23a- 2003
ANSI Z21.24-2001 Connectors for Gas Appliances [UMC 1312.1(3)]Addenda Z21.24a-2002Addenda Z21.24b-2003
ANSI Z21.35-1995 (R2002) Pilot Gas FiltersAddenda Z21.35a-1997 (R2002)Addenda Z21.35b-2000 (R2002)
ANSI Z21.40.1-1996 (R2002) Gas-Fired, Heat Activated, Air Conditioning and Heat Pump AppliancesCSA 2.9.1-M96
ANSI Z21.41-2003 Quick-Disconnect Devices for Use with Fuel Gas
ANSI Z21.42- 1997 (R2002) Gas-Fired Illuminating Appliances
ANSI Z21.45-1995 Flexible Connectors for Other Than All-Metal Construction for Gas Appliances
ANSI Z21.47-2003/ CSA 2.3-2003 Gas-Fired Central Furnaces
ANSI Z21.50-2003 Decorative Gas Appliances, VentedAddenda Z21.50a-2003Addenda Z21.50b-2002
ANSI Z21.54-2002 Gas Hose Connectors for Portable Outdoor Gas-Fired Appliances
ANSI Z21.56-2001 Gas-Fired Pool HeatersAddenda Z21.56a-2003
ANSI Z21.58a-2004 Outdoor Gas Cooking Appliances
ANSI Z21.60- 2003 Decorative Gas Appliances for Installation in Solid-Fuel Burning FireplacesAddenda Z21.60a-2003
ANSI Z21.61-1983 (R2004) Gas-Fired Toilets
ANSI Z21.66-1996 (R2001) Automatic Vent Damper Devices for Use with Gas-Fired Appliances
ANSI Z21.69- 2002 CSA 6.16-02 Connectors for Moveable Gas Appliances [UMC 303.1(5), 1312.1(6)]Addenda Z21.69a-2003/CGA 6.16a
Addenda Z21.69b-2001/
Item #107
STANDARDS Chapter 17
Standard Number Standard Title [UMC References]
CGA 6.16b
ANSI Z21.71-(R2002) Automatic Intermittent Ignition Systems for Field Installation
ANSI Z21.80-2003 CSA 6.22-M97 Line Pressure Regulators [UMC 1309.7.2, 1309.9.7.5(A)]
ANSI Z21.83-1998 Fuel Cell Power Plants [UMC 1601.0]
ANSI Z21.86-2003 Gas-Fired Vented Heating Appliances
ANSI Z21.88-2002 Vented Gas Fireplace HeatersAddenda Z21.88a-2003
ANSI Z83.4-1999 CSA 3.7-M99 Non-Recirculating Direct Gas-Fired Industrial Air Heaters [UMC 909.1]Addenda Z83.4a2001CSA 3.7a-2001
ANSI Z83.7-2000 Gas-Fired Construction Heaters
ANSI Z83.8- 2002 CSA 2.6-2002 Gas Unit Heaters and Gas-Fired Duct FurnacesAddenda Z83.8a-2003
ANSI Z83.11-2002 Gas Food Service Equipment
ANSI Z83.18-2000 Recirculating Direct Gas-Fired Industrial Air Heaters [UMC 910.1]Addenda Z83.18a-2001Addenda Z83.18b-2003
ANSI Z83.19a-2002 Gas-Fired High Intensity Infrared Heaters
ANSI Z83.20-2001 Gas-Fired Tube Type and Low Intensity Infrared HeatersAddenda Z83.20a-2002Addenda Z83.20b-2004
ANSI Z223.1-99 National Fuel Gas Code (same as NFPA 54)
ARI 700-99 1997 Specification for Fluorocarbon Refrigerant
ARI 1010-2002 Drinking Fountains and Self-Contained, Mechanically Refrigerated Drinking Water Coolers
ASCE 25-1999 Earthquake Actuated Automatic Gas Shutoff Devices
ASHRAE Handbook Fundamentals, Climatic Conditions for the United States; Chapter 27, Table 1A and B, 2001
ASHRAE Volume 1980 Panel Heating Systems
ASHRAE 15-2004 Safety Standard for Refrigeration Systems
ASHRAE 34-2004 Designation and Safety Classification of Refrigerants
ASHRAE 62.1-2004 Ventilation for Acceptable Indoor Air Quality, Addenda h,i,k,n,o,r,t,u,v,x,z,ab,ad,ae,and,af[UMC 403.4.2]
ASHRAE Climatic Conditions ASHRAE Handbook - Fundamentals, Chapter 27, Table 1A&B, for the US 2001
ASME A112.4.1-93 (R02) Water Heater Relief Valve Drain Tubes
ASME A112.18.6- 2003 Flexible Water Connectors
ASME A112.20.1-2004 Qualification of Installers of High Purity Piping Systems
ASME B1.20.1-98 Pipe Threads, General Purpose, Inch [UMC 1309.5.7(A)]
ASME B1.20.3-76 (R2003) Dryseal Pipe Threads, Inch Joints
ASME B16.1-1998 Cast-Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, and 250, and 800 Piping,Ferrous [UMC 1309.5.10]
ASME B16.18-2001 Cast Copper Alloy Solder Joint Pressure Fittings
Item #107
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
ASME B16.22-2001 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
ASME B16.23-2002 Cast Copper Alloy Solder Joint Drainage Fittings
ASME B16.24-2001 Cast Copper Alloy Pipe Flanged Fittings: Classes 150, 300, 400, 600, 900, 1500, and 2500
ASME B16.26-1988 Cast Copper Alloy Fittings for Flared Copper Tubes
ASME B16.29-2001 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings
ASME B16.33-2002 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psi (Sizes 1/2 NPS - 2 NPS 24)
ASME B16.38-(R1994) Large Metallic Valves for Gas Distribution (Manually Operated, NPS 2-1/2 to 12, 125 psig/Maximum)
ASME B16.50-2001 Wrought Copper and Wrought Copper Alloy Braze-Joint Pressure Fittings
ASME B36.10M-2001 Welded and Seamless Wrought Steel Pipe [UMC 1309.5.2.2]
ASME Section IV Rules for Construction of Heating Boilers
ASME Section VIII Rules for Construction of Pressure Vessels
ASSE 1005-1999 Water Heater Drain Valves
ASTM A 53- 2002 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded, and Seamless [UMC 1309.5.2.2(2)]
ASTM A 312-2003 Seamless and Welded Austenitic Stainless Steel Pipes
ASTM A 653M- 2003 Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM A 733-2003 Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples
ASTM A 861- 2002 High-Silicon Iron Pipe and Fittings (Note 1)
ASTM B 32-2004 Solder Metal (see Section 1201.2.3.7 for restriction)
ASTM B 42-2002e1 Seamless Copper Pipe, Standard Sizes
ASTM B 43-1998e1 Seamless Red Brass Pipe, Standard Sizes
ASTM B 75-2002 Seamless Copper Tube
ASTM B 88-2003 Seamless Copper Water Tube, (K, L, M) [UMC 1309.5.3.2]
ASTM B 135-2002 Seamless Brass Tube
ASTM B 280-2003 Seamless Copper Tube for Air Conditioning and Refrigeration Field Service [UMC 1309.5.3.2]
ASTM B 302-2002 Threadless Copper Pipe (TP)
ASTM B 306-2002 Copper Drainage Tube (DWV)
ASTM B 370-1998 Copper Sheet and Strip for Building Construction
ASTM B 447-2002 Welded Copper Tube
ASTM B 584-2000 Copper Alloy Sand Casting for General Applications (Note 5)
ASTM B 587-1997 (R2003) Welded Brass Tube
ASTM B 687-1999 Brass, Copper, and Chromium-Plated Pipe Nipples
ASTM B 813-00e1 Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
ASTM B 828-02 Standard Practice for Making Capillary Joints in Copper and Copper Alloy Tube and Fittings
ASTM C 411-1997 Hot-Surface Performance of High Temperature Thermal Insulation [UMC 605.0,1201.4.1.3]
ASTM C 518-2004 Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter
Item #107
STANDARDS Chapter 17
Standard Number Standard Title [UMC References]
Apparatus
ASTM E 84-2004 Surface Burning Characteristics of Building Materials [UMC 602.2, 605.0, 1201.4.1.3]
ASTM E 814-2002 Fire Tests of Through Penetration Fire Stops
ASTM E 2231-2002 Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics [UMC 605.0, 1201.4.1.3]
ASTM F 1281-03 Crosslinked Polyethylene/ Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe [UMC 1201.5, 1201.5.1.1, 1201.5.2]
ASTM F 1961-02a Metal Mechanical Cold Flare Compression Fittings with Disc Springs for Crosslinked Polyethylene (PEX) Tubing
ASTM F 2158-2001 Residential Central-Vacuum Tube and Fittings
AWS A5.8-92 Filler Metals for Brazing and Braze Welding
AWWA C110-2003 Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1,200 mm), for Water and Other Liquids (same as ANSI A21.10-98)
AWWA C151-2002 Ductile-Iron Pipe, Centrifugally Cast, for Water (same as ANSI A21.51-91)
AWWA C203-2002 Coal-Tar Protective Coatings and Linings for Steel Water Pipelines Enameled and Tape Hot Applied
AWWA C500-2002 Metal-Seated Gate Valves for Water and Sewerage Systems Valves
CAN/CGSB 3.2-99 Heating Fuel Oil
CSA F379.1-88 Solar Domestic Hot Water Systems (Liquid to Liquid Heat Transfer)
IAPMO IS 13-2003 Installation Standard for Protectively Coated Pipe
IAPMO PS 14-2002 [D] Flexible Metallic Field Fabricated Water Connectors
IAPMO PS 33-2000a Flexible PVC Hose for Pools, Hot Tubs, Spas and Jetted Bathtubs
IAPMO PS 120-2004 Flashing and Stand Combination for Air Conditioning Units (Residential or Commercial Unit Curb)
IAS 1-91 U.S. Requirements for Indirect Water Heaters for Use With External Heat Source
IAS LC 1-01 CSA 6.26-01 Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST) Fuel Gas[UMC 1309.5.3.4
I-B-R First Edition August, 2002 Rating Procedure for Heating Boilers
ISO Guide 65:1996 General Requirements for Bodies Operating Product Certification Systems
MSS SP-58-02 Pipe Hangers and Supports Materials, Design, and Manufacture [UMC 1311.2.6(A)]
MSS SP-67-02 Butterfly Valves
MSS SP-69-02 Pipe Hangers and Supports - Selection and Application
MSS SP-73-03 [D] Brazing Joints for Wrought and Cast Copper Alloy Solder Joint Pressure Fittings
MSS SP-80-03 Bronze Gate-Globe, Angle, and Check Valves
MSS SP-89-98 Pipe Hangers and Supports - Fabrication and Installation Practices
MSS SP-104-03 Wrought Copper Solder Joint Pressure Fittings
MSS SP-106-03 Cast Copper Allot Flanges and Flanged Fittings, Class 125, 150, and 300
MSS SP-109-97 Welded Fabricated Copper Solder Joint Pressure Fittings
NFPA 30-2003 Flammable and Combustible Liquids Code [UMC 204.0]
Item #107
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
NFPA 31-2006 Installation of Oil Burning Equipment [UMC 302.3, 1020.0, 1302.0]
NFPA 52-2005 Compressed Natural Gas (CNG) Vehicular Fuel Systems
NFPA 54-2005/ANSI Z223.1 National Fuel Gas Code (same as ANSI Z223.1) [UMC 303.3(D), 516.2.1, 1309.7.5(D), 1311.4, 1311.4.1]
NFPA 58-2004 Liquefied Petroleum Gas Code [UMC 516.2.1, 1309.5.4.3, 1309.5.9(D), 1313.0]
NFPA 69-2002 Explosion Prevention Systems
NFPA 70-2005 National Electrical Code [UMC 511.1.6, 512.2.5, 516.2.5, 516.2.7(D), 602.2(5), 1311.12.5(B)]
NFPA 85-2004 Boiler and Combustion Systems Hazard Code [UMC 1002.0(9), 1020.0]
NFPA 96-2004 Ventilation Control and Fire Protection of Commercial Cooking Operations
NFPA 211-2003 Chimneys, Fireplaces, Vents, and Solid Fuel Burning Appliances[UMC 517.7.1, 517.7.2, 517.7.3, 801.1, 801.2, 802.5.1.2, 802.5.1.3, 802.5.4]
NFPA 255-2005 Method of Test of Burning Characteristics of Building Materials [UMC 602.2, 605.0, 1201.4.1.3]
NFPA 262-2006 Flame Travel and Smoke of Wires and Cables for Use in Air-Handling Spaces [UMC 602.2(5)]
NFPA 654-2005 Prevention of Fire and Dust Explosion from the Manufacturing, Processing, and Handlingof Combustible Particulate Solids [UMC 506.4]
NFPA 853-2006 Installation of Stationary Fuel Cell Power Plants [UMC 1601.0]
PPI TR-4, 2004 Recommended Hydrostatic Strengths and Design Stresses for Thermoplastic Pipe and Fittings Compounds
SAE J512-97 Automotive Tube Fittings
SMACNA, 1995 HVAC Duct Construction Standards - Metal and FlexibleAddendum 1, 11/97
SMACNA 1884, 2003 Fibrous Glass Duct Construction Standard
UL 17, 1994 edition 3 Vent or Chimney Connector Dampers for Oil-Fired Appliances
UL 21, 1995 edition 9 LP-Gas Hose
UL 33, 2003 edition 7 Heat Responsive Links for Fire Protection Service
UL 51, 2002 edition 9 Power-Operated Pumps for Anhydrous Ammonia and LP-Gas
UL 80, 2004 edition 11 Steel Tanks for Oil-Burner Fuel
UL 103, 2001 edition 10 Factory-Built Chimneys for Residential Type and Building Heating Appliances
UL 125-1997 edition 6 Valves for Anhydrous Ammonia and LP-Gas (Other than Safety Relief)
UL 127-1996 edition 7 Factory-Built Fireplaces
UL 132, 1997 edition 6 Safety Relief Valves for Anhydrous Ammonia and LP-Gas
UL 144, 1999 edition 7 LP-Gas Regulators
UL 174, 2004 edition 11 Household Electric Storage Tank Water Heaters
UL 180-2003 edition 7 Liquid Level Indicating Gauges for Oil Burner Fuels
UL 181, 1996 edition 10 Factory-Made Air Ducts and Air Connectors
UL 181A, 1994 edition 3 Closure Systems for Use with Rigid Air Ducts and Air Connectors
UL 181B, 1995 edition 2 Closure Systems for Use with Flexible Air Ducts and Air Connectors
UL 197, 2003 edition 9 Commercial Electric Cooking Appliances [UMC 513.2.2]
UL 207, 2001 edition 7 Non-Electrical Refrigerant-Containing Components and Accessories
UL 252, 2003 edition 8 Compressed Gas Regulators
Item #107
STANDARDS Chapter 17
Standard Number Standard Title [UMC References]
UL 268A, 1998 edition 3 Smoke Detectors for Duct Application
UL 296, 2003 edition 10 Oil Burners
UL 300, 1996 edition 3 Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas [UMC 513.2.2]
UL 343, 1997 edition 8 Pumps for Oil-Burning Appliances
UL 352, 1997 edition 7 Constant-Level Oil Valves
UL 353, 1994 edition 5 Limit Controls
UL 378, 1993 edition 3 Draft Equipment
UL 391, 1995 edition 3 Solid-Fuel and Combination Fuel Central and Supplementary Furnaces
UL 404, 1997 edition 7 Indicating Pressure Gauges for Compressed Gas Service
UL 412, 2004 edition 4 Refrigeration Unit Coolers
UL 429, 1999 edition 5 Electrically Operated Valves
UL 441, 1996 edition 9 Gas Vents
UL 443, 1995 edition 5 Steel Auxilliary Tanks for Oil Burner Fuel
UL 471, 1995 edition 8 Commercial Refrigerators and Freezers
UL 525, 2004 edition 7 Flame Arresters
UL 536, 1997 edition 9 Flexible Metallic Hose
UL 555, 1999 edition 6 Fire Dampers
UL 555C, 1996 edition 2 Ceiling Dampers
UL 555S, 1999 edition 4 Smoke Dampers
UL 565, 1998 edition 5 Liquid Level Gauges and Indicators for Anhydrous Ammonia and LP-Gas
UL 569, 1995 edition 7 Pigtails and Flexible Hose Connectors for LP-Gas
UL 641, 1995 edition 7 Type L Low Temperature Venting Systems
UL 710, 1995 edition 5 Exhaust Hoods for Commercial Cooking Equipment
UL 723, 2003 edition 9 Test for Surface Burning Characteristics of Building Materials [UMC 508.3, 602.2, 605.0(E), 1201.4.1.3]
UL 726, 1995 edition 7 Oil-Fired Boiler Assemblies
UL 727, 1994 edition 8 Oil-Fired Central Furnaces
UL 729, 2003 edition 6 Oil-Fired Floor Furnaces
UL 730, 2003 edition 5 Oil-Fired Wall Furnaces
UL 731, 1995 edition 5 Oil-Fired Heater Units
UL 732, 1995 edition 5 Oil-Fired Storage Tank Water Heaters
UL 733, 1993 edition 4 Oil-Fired Water Heaters and Direct-Fired Heaters
UL 737, 1996 edition 8 Fireplace Stoves
UL 791, 1993 edition 4 Residential Incinerators
UL 795, 1999 edition 5 Commercial-Industrial Gas Heating Equipment (Inputs over 400,000 Btu per hour)
UL 834, 2004 edition 5 Electric Water Supply Heating and Power Boilers
Item #107
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
UL 842, 1997 edition 8 Valves for Flammable Fluids
UL 858, 1993 edition 15 Household Electric Ranges
UL 867, 2000 edition 4 Electrostatic Air Cleaners
UL 896, 1993 edition 5 Oil-Burning Stoves
UL 900, 2004 edition 7 Air Filter Units
UL 907, 1994 edition 2 Fireplace Accessories
UL 921, 1996 edition 5 Commercial Electric Dishwashers
UL 959, 2001 edition 8 Medium Heat Appliance Factory-Built Chimneys
UL 984, 1996 edition 7 Hermetic Refrigerant Motor Compressors
UL 1026, 1995 edition 4 Electric Household Cooking and Food Serving Appliances
UL 1046, 2000 edition 3 Grease Filters for Exhaust Ducts [UMC 509.1]
UL 1206, 2003 edition 4 Electric Commercial Clothes-Washing Equipment
UL 1240, 1994 edition 3 Electric Commercial Clothes-Drying Equipment
UL 1453, 2004 edition 5 Electric Booster and Commercial Storage Tank Water Heaters
UL 1482, 1996 edition 5 Solid-Fuel Type Room Heaters
UL 1738, 1993 edition 2 Venting Systems for Gas-Burning Appliances, Categories II, III, and IV
UL 1746, 1993 edition 2 External Corrosion Protection Systems for Steel Underground Storage Tanks
UL 1777, 2004 edition 3 Chimney Liners
UL 1812, 1995 edition 2 Ducted Heat Recovery Ventilators
UL 1815, 2001 edition 3 Nonducted Heat Recovery Ventilators
UL 1820, 2004 edition 4 Fire Test of Pneumatic Tubing for Flame and Smoke Characteristics [UMC 602.2(7)]
UL 1887, 2004 edition 3 Fire Test of Plastic Sprinkler Pipe for Visible Flame and Smoke Characteristics [UMC 602.2(6)]
UL 1963, 1995 edition 2 Refrigerant Recovery/ Recycling Equipment
UL 1978, 2002 edition 3 Grease Ducts
UL 1995, 1995 edition 3 Heating and Cooling Equipment
UL 2021, 1997 edition 2 Fixed and Location-Dedicated Electric Room Heaters
UL 2043, 1996 edition 2 Fire Test for Heat and Visible Smoke Release for Discrete Products and Their Accessories Installed in Air Handling Spaces [UMC 602.2(8)]
UL 2157, 1997 edition 2 Electric Clothes Washing Machines and Extractors
UL 2158, 1995 edition 2 Electric Clothes Dryers
Item #107
UMC 2009 – August 2007 ROP
SUBMITTER:
Revise table as follows:
(See attached Table 17–1 Standards for Equipment and Materials on pages 170–1 through 170–8)
Updating the standards in Table 17–1 in the UMC to the most current published version.
SUBSTANTIATION:
RECOMMENDATION:
UMC 2009 Table 17–1
Based on committee action taken on Item 111.
Reject
John Taecker
108-
UMC Standards Task Group
TOTAL ELIGIBLE TO VOTE: 24
VOTING RESULTS: AFFIRMATIVE: 22, NOT RETURNED: 2 T. Nothaft, D. Bixby
COMMITTEE ACTION:
COMMITTEE STATEMENT:
Item #
SUBMITTER:
Add text as follows:
(See attachment Standards to be added to Table 17–1 on pages 170–9 through 170–10)
The following list of standards has been endorsed by the UMC Chp. 17 Task Group as new reference standards for Table 17–1
SUBSTANTIATION:
RECOMMENDATION:
UMC 2009 Table 17–1
Based on committee action taken on Item 111.
Reject
John Taecker
109-
UMC Standards Task Group
TOTAL ELIGIBLE TO VOTE: 24
VOTING RESULTS: AFFIRMATIVE: 22, NOT RETURNED: 2 T. Nothaft, D. Bixby
COMMITTEE ACTION:
COMMITTEE STATEMENT:
Item #
170
Standard Number Standard Title [UMC References]
ACCA Manual D Residential Duct Systems
ACCA Manual J Residential Load Calculations
ACCA Manual N Commercial Load Calculation
ACCA Manual Q Low Pressure Low Velocity Duct Systems Design
ANSI ASME A13.1-96 (R2002) Scheme for the Identification of Piping Systems
ANSI A21.10-03 Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1200 mm), for Water and Other Liquids (same as AWWA C110)
ANSI A21.51-02 Ductile-Iron Pipe, Centrifugally Cast, for Water (same as AWWA C151)
ANSI B1.20.1-1983 (R2001) Pipe Threads, General Purpose, Inch (Except Dryseal) (replaced by ASME B1.20.1-98)
ANSI B1.20.3-1976 (R2003) Dryseal Pipe Threads (Inch)
ASME B31.5-2001 Refrigeration Piping
ANSI CSA Z21.1-2000 05 Household Gas Cooking AppliancesAddendum Z21.1a-2003
ANSI Z21.5.1-2002 CSA A7.1b-2005 Gas Clothes Dryers - Volume I, Type I (same as ANSI Z21.5.1b-05)ANSI Z21.5.1a-2003
Addenda Z21.5.1a-2002
ANSI Z21.5.2-2001 Gas Clothes Dryers - Volume II, Type 2 (same as ANSI Z21.5.2-05)CSA 7.2-2001 05
ANSI Z21.5.2a-2003Addenda Z21.5.2a-2003
ANSI CSA Z21.8-(R2002) Installation of Domestic Gas Conversion Burners [UMC 906.0]
ANSI Z21.10.1-2004 CSA 4.1ab-02 2006 Gas Water Heaters, Volume I, Water Heaters with Input Ratings of 75,000 Btu per Hour or Less (same as ANSI Z21.10.1b-06)
ANSI Z21.10.3-2004 CSA 4.3-2004 Gas Water Heaters, Volume III, Water Heaters with Input Ratings Above 75,000 Btu perHour, Circulating and Instantaneous Water Heaters (same as ANSI Z21.10.3-04)
ANSI CSA Z21.11.2b- 2002 04 Gas-Fired Unvented Room Heaters, Volume II (same as ANSI Z21.11.2b-04)Addenda Z21.11.2a-2003
ANSI CSA Z21.12-1990 94 (R2000) Draft Hoods (same as ANSI Z21.12-94)Addenda Z21.12a-1993 (R2000)Addenda Z21.12b-1994 (R2000)
ANSI Z21.13-2004 CSA 4.9a-02 2005 Gas-Fired Low Pressure Steam and Hot Water Boilers (same as ANSI Z21.13a-05)
ANSI Z21.15-1997 (R2003) CSA 9.1a-2001 (R2003) Valves for Appliances, Appliance Connector Valves and Hose End Addenda Z21.15a-2001 (R2003) Valves, Manually Operated Gas (same as ANSI Z21.15a-01/CGA 9.1)
CHAPTER 17
TABLE 17-1Standards for Equipment and Materials
Note: This Chapter has been revised and reformatted in its entirety.
No arrows or side bars have been used to signify changes.
Item #108
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
ANSI Z21.17-1998 CSA 2.7-M98 (R2004) Installation of Domestic Gas Conversion Burners (same as ANSI Z21.17-98)
ANSI Z21.18-2000 CSA 6.3b-2005 Gas Appliance Pressure Regulators (same as ANSI Z21.18b-05)Addenda Z21.18a-2001
ANSI Z21.19-2002 CSA 1.4-2002 Refrigerators Using Gas Fuel (same as ANSI Z21.19-02)
ANSI CSA Z21.20-2000 Automatic Gas Ignition Systems and Components (same as ANSI Z21.20b-01)Addenda Z21.20a-2000
Addenda Z21.20b-2001
ANSI Z21.21-2000 CSA 6.5-2005 Automatic Valves for Gas Appliances (same as ANSI Z21.21-05)Addenda Z21.21a-2001
ANSI Z21.22-1999 (R2003) Relief Valves for Hot Water Supply Systems (same as ANSI Z21.13b-01)CSA 4.4b-00 01 (R2003)
Addenda Z21.22a-2000Addenda Z21.22b-2001
ANSI Z21.23b-2000 05 Gas Appliance ThermostatsAddenda Z21.23a- 2003
ANSI Z21.24-2001 CSA 6.10b-2003 Connectors for Gas Appliances (same as ANSI Z21.24b-03) [UMC 1312.1(3)]Addenda Z21.24a-2002
Addenda Z21.24b-2003
ANSI Z21.35-1995 (R2002) CSA 6.8-2005 Pilot Gas Filters (same as ANSI Z21.35-05)Addenda Z21.35a-1997 (R2002)Addenda Z21.35b-2000 (R2002)
ANSI Z21.40.1-1996 (R2002) Gas-Fired, Heat Activated, Air Conditioning and Heat Pump AppliancesCSA 2.9.1a-M96 97 (R2002) (same as ANSI Z21.40.1-97/CGA 2.91)
ANSI Z21.41-2003 CSA 6.9a-2005 Quick-Disconnect Devices for Use with Fuel Gas (same as ANSI Z21.41a-05)
ANSI CSA Z21.42a- 1997 (R2002) 2004 Gas-Fired Illuminating Appliances (same as ANSI Z21.42a-04)
ANSI Z21.45-1995 [D] Flexible Connectors for Other Than All-Metal Construction for Gas Appliances
ANSI Z21.47-2003/ CSA 2.3b-2003 06 Gas-Fired Central Furnaces (same as ANSI Z21.47b-06)
ANSI Z21.50-2003 CSA 2.22b-2005 Decorative Gas Appliances, Vented (same as ANSI Z21.50b-05)Addenda Z21.50a-2003Addenda Z21.50b-2002
ANSI Z21.54-2002 CSA 8.4a-2006 Gas Hose Connectors for Portable Outdoor Gas-Fired Appliances (same as ANSIZ21.54a-06)
ANSI Z21.56-2001 CSA 4.7-2006 Gas-Fired Pool Heaters (same as ANSI Z21.56-06)Addenda Z21.56a-2003
ANSI Z21.58a-2004 CSA 1.6b-2006 Outdoor Gas Cooking Appliances (same as ANSI Z21.58b-06)
ANSI Z21.60- 2003 CSA 2.26b-2004 Decorative Gas Appliances for Installation in Solid-Fuel Burning Fireplaces Addenda Z21.60a-2003 (same as ANSI Z21.60b-04)
ANSI CSA Z21.61-1983 (R2004) Gas-Fired Toilets (same as ANSI Z21.61-83)
ANSI Z21.66-1996 (R2001) CSA 6.14-96 (R2001) Automatic Vent Damper Devices for Use with Gas-Fired Appliances
(same as ANSI Z21.66-96/CGA 6.14)
ANSI Z21.69- 2002 CSA 6.16b-022006 Connectors for Moveable Gas Appliances [UMC 303.1(5), 1312.1(6)]Addenda Z21.69a-2003/ (same as ANSI Z21.69b-06)
Item #108
STANDARDS Chapter 17
Standard Number Standard Title [UMC References]
CGA 6.16aAddenda Z21.69b-2001/ CGA 6.16b
ANSI CSA Z21.71a- 2005 (R2002) Automatic Intermittent Ignition Systems for Field Installation (same as ANSI Z21.71a-05)
ANSI Z21.80-2003 CSA 6.22a-M97 2005 Line Pressure Regulators (same as ANSI Z21.80a-05) [UMC 1309.7.2, 1309.9.7.5(A)]
ANSI Z21.83-1998 CSA America FC 1-2004 Fuel Cell Power Plants [UMC 1601.0]
ANSI Z21.86-2003 CSA 2.32a-2005 Gas-Fired Vented Heating Appliances (same as ANSI Z21.86a-05)
ANSI Z21.88-2002 CSA 2.33-2005 Vented Gas Fireplace Heaters (same as ANSI Z21.88-05)Addenda Z21.88a-2003
ANSI Z83.4-1999 CSA 3.7b-M99 2006 Non-Recirculating Direct Gas-Fired Industrial Air Heaters [UMC 909.1]Addenda Z83.4a2001 (same as ANSI Z83.4b-06)CSA 3.7a-2001
ANSI Z83.7-2000 CSA 2.4-2000 (R2006) Gas-Fired Construction Heaters (same as ANSI Z83.7-00)
ANSI Z83.8- 2002 CSA 2.6-2002 06 Gas Unit Heaters and Gas-Fired Duct Furnaces (same as ANSI Z83.8-06)Addenda Z83.8a-2003
ANSI Z83.11-2002 CSA 1.8b-2006 Gas Food Service Equipment (same as ANSI Z83.11b-06)
ANSI CSA Z83.18a-2000 05 Recirculating Direct Gas-Fired Industrial Air Heaters [UMC 910.1]Addenda Z83.18a-2001 (same as ANSI Z83.18a-05)Addenda Z83.18b-2003
ANSI Z83.19a-2002 CSA 2.35a-2002 Gas-Fired High Intensity Infrared Heaters (same as ANSI Z83.19a-02)
ANSI Z83.20-2001 CSA 2.34b-2004 Gas-Fired Tube Type and Low Intensity Infrared Heaters (same as ANSI Z83.20b-04)Addenda Z83.20a-2002Addenda Z83.20b-2004
ANSI Z223.1-99 National Fuel Gas Code (same as NFPA 54)
ARI 700-99 Specification for Fluorocarbon Refrigerant
ARI 1010-2002 UL 399-1993 Drinking Fountains and Self-Contained, Mechanically Refrigerated Drinking Water Coolers
edition 6
ASCE 25-1999 Earthquake Actuated Automatic Gas Shutoff Devices
ASHRAE Handbook Fundamentals, Climatic Conditions for the United States; Chapter 27, Table 1A and B, 2001
ASHRAE Volume 1980 Panel Heating Systems
ASHRAE 15-2004 Safety Standard for Refrigeration Systems
ASHRAE 34-2004 Designation and Safety Classification of Refrigerants
ASHRAE 62.1-2004 Ventilation for Acceptable Indoor Air Quality, Addenda h,i,k,n,o,r,t,u,v,x,z,ab,ad,ae,and,af[UMC 403.4.2]
ASHRAE Climatic Conditions ASHRAE Handbook - Fundamentals, Chapter 27, Table 1A&B, for the US 2001
ASME A112.4.1-93 (R02) Water Heater Relief Valve Drain Tubes
ASME A112.18.6- 2003 Flexible Water Connectors
ASME A112.20.1-2004 Qualification of Installers of High Purity Piping Systems
ASME B1.20.1-98 (R2006) Pipe Threads, General Purpose, Inch [UMC 1309.5.7(A)]
ASME B1.20.3-76 (R2003) Dryseal Pipe Threads, Inch Joints
Item #108
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
ASME B16.1-1998 Cast-Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, 250, and 800 Piping,Ferrous [UMC 1309.5.10]
ASME B16.18-2001 Cast Copper Alloy Solder Joint Pressure Fittings
ASME B16.22-2001 (R2005) Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
ASME B16.23-2002 Cast Copper Alloy Solder Joint Drainage Fittings
ASME B16.24-2001 Cast Copper Alloy Pipe Flanged Fittings
ASME B16.26-1988 Cast Copper Alloy Fittings for Flared Copper Tubes
ASME B16.29-2001 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings
ASME B16.33-2002 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psi (Sizes 1/2 NPS - 2)
ASME B16.38-(R1994) [D] Large Metallic Valves for Gas Distribution (Manually Operated, NPS 2-1/2 to 12, 125 psig/Maximum)
ASME B16.50-2001 Wrought Copper and Wrought Copper Alloy Braze-Joint Pressure Fittings
ASME B36.10M-2001 04 Welded and Seamless Wrought Steel Pipe [UMC 1309.5.2.2]
ASME Section IV Rules for Construction of Heating Boilers
ASME Section VIII Rules for Construction of Pressure Vessels
ASSE 1005-1999 [D] Water Heater Drain Valves
ASTM A 53- 2002 06a Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded, and Seamless [UMC 1309.5.2.2(2)]
ASTM A 312M-2003 06 Seamless, and Welded and Heavy Cold Worked of Austenitic Stainless Steel Pipes
ASTM A 653M- 2003 06 Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM A 733-2003 Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples
ASTM A 861- 2002 04 High-Silicon Iron Pipe and Fittings (Note 1)
ASTM B 32-2004 Solder Metal (see Section 1201.2.3.7 for restriction)
ASTM B 42-2002e1 Seamless Copper Pipe, Standard Sizes
ASTM B 43-1998e1 (R2004) Seamless Red Brass Pipe, Standard Sizes
ASTM B 75-2002 Seamless Copper Tube
ASTM B 88-2003 Seamless Copper Water Tube, (K, L, M) [UMC 1309.5.3.2]
ASTM B 135-2002 Seamless Brass Tube
ASTM B 280-2003 Seamless Copper Tube for Air Conditioning and Refrigeration Field Service [UMC 1309.5.3.2]
ASTM B 302-2002 Threadless Copper Pipe (TP)
ASTM B 306-2002 Copper Drainage Tube (DWV)
ASTM B 370-1998 2003 Copper Sheet and Strip for Building Construction
ASTM B 447-2002 Welded Copper Tube
ASTM B 584-2000 [D] Copper Alloy Sand Casting for General Applications (Note 5)
ASTM B 587-1997 (R2003) 2006 Welded Brass Tube
ASTM B 687-1999 (R2005)e1 Brass, Copper, and Chromium-Plated Pipe Nipples
ASTM B 813-00e1 Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
Item #108
STANDARDS Chapter 17
Standard Number Standard Title [UMC References]
ASTM B 828-02 Standard Practice for Making Capillary Joints in Copper and Copper Alloy Tube and Fittings
ASTM C 411-1997 2005 Hot-Surface Performance of High Temperature Thermal Insulation [UMC 605.0,1201.4.1.3]
ASTM C 518-2004 Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM E 84-2004 06 Surface Burning Characteristics of Building Materials [UMC 602.2, 605.0, 1201.4.1.3]
ASTM E 814-2002 06 Fire Tests of Through Penetration Fire Stops
ASTM E 2231-2002e1 Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics [UMC 605.0, 1201.4.1.3]
ASTM F 1281-03 2005 Crosslinked Polyethylene/ Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe [UMC 1201.5, 1201.5.1.1, 1201.5.2]
ASTM F 1961-02a Metal Mechanical Cold Flare Compression Fittings with Disc Springs for Crosslinked Polyethylene (PEX) Tubing
ASTM F 2158-2001 Residential Central-Vacuum Tube and Fittings
AWS A5.8-92 2004 Specification for Filler Metals for Brazing and Braze Welding
AWWA C110-2003 Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1,200 mm), for Water and Other Liquids (same as ANSI A21.10-98)
AWWA C151-2002 Ductile-Iron Pipe, Centrifugally Cast, for Water or Other Liquids (same as ANSI A21.51-91)
AWWA C203-2002 Coal-Tar Protective Coatings and Linings for Steel Water Pipelines Enameled and Tape Hot Applied
AWWA C500-2002 Gate Valves for Water and Sewerage Systems Valves
CAN/CGSB 3.2-99 Heating Fuel Oil
CSA F379.1-88 (R1999) Solar Domestic Hot Water Systems (Liquid to Liquid Heat Transfer)
IAPMO IS 13-2003 06 Installation Standard for Protectively Coated Pipe
IAPMO PS 14-2002 [D] Flexible Metallic Field Fabricated Water Connectors
IAPMO PS 33-2000a Flexible PVC Hose for Pools, Hot Tubs, Spas and Jetted Bathtubs
IAPMO PS 120-2004 Flashing and Stand Combination for Air Conditioning Units (Residential or Commercial Unit Curb)
IAS 1-91 U.S. Requirements for Indirect Water Heaters for Use With External Heat Source
IAS LC 1-01 CSA 6.26-01 2005 Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST) Fuel Gas(same as ANSI LC 1)
I-B-R First Edition August, 2002 Rating Procedure for Heating Boilers
ISO Guide 65:1996 General Requirements for Bodies Operating Product Certification Systems
MSS SP-58-02 Pipe Hangers and Supports Materials, Design, and Manufacture [UMC 1311.2.6(A)]
MSS SP-67-02a Butterfly Valves
MSS SP-69-02 2003 Pipe Hangers and Supports - Selection and Application
MSS SP-73-03 Brazing Joints for Wrought and Cast Copper Alloy Solder Joint Pressure Fittings
MSS SP-80-03 Bronze Gate-Globe, Angle, and Check Valves
MSS SP-89-98 2003 Pipe Hangers and Supports - Fabrication and Installation Practices
Item #108
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
MSS SP-104-03 Wrought Copper Solder Joint Pressure Fittings
MSS SP-106-03 Cast Copper Allot Flanges and Flanged Fittings, Class 125, 150, and 300
MSS SP-109-97 (R2006) Welded Fabricated Copper Solder Joint Pressure Fittings
NFPA 30-2003 Flammable and Combustible Liquids Code [UMC 204.0]
NFPA 31-2006 Installation of Oil Burning Equipment [UMC 302.3, 1020.0, 1302.0]
NFPA 52-2005 06 Compressed Natural Gas (CNG) Vehicular Fuel Systems
NFPA 54-2005 06/ANSI Z223.1 National Fuel Gas Code (same as ANSI Z223.1) [UMC 303.3(D), 516.2.1, 1309.7.5(D), 1311.4, 1311.4.1]
NFPA 58-2004 Liquefied Petroleum Gas Code [UMC 516.2.1, 1309.5.4.3, 1309.5.9(D), 1313.0]
NFPA 69-2002 Explosion Prevention Systems
NFPA 70-2005 National Electrical Code [UMC 511.1.6, 512.2.5, 516.2.5, 516.2.7(D), 602.2(5), 1311.12.5(B)]
NFPA 85-2004 07 Boiler and Combustion Systems Hazard Code [UMC 1002.0(9), 1020.0]
NFPA 96-2004 Ventilation Control and Fire Protection of Commercial Cooking Operations
NFPA 211-2003 06 Chimneys, Fireplaces, Vents, and Solid Fuel Burning Appliances[UMC 517.7.1, 517.7.2, 517.7.3, 801.1, 801.2, 802.5.1.2, 802.5.1.3, 802.5.4]
NFPA 255-2005 06 Method of Test of Burning Characteristics of Building Materials [UMC 602.2, 605.0, 1201.4.1.3]
NFPA 262-2006 07 Flame Travel and Smoke of Wires and Cables for Use in Air-Handling Spaces [UMC 602.2(5)]
NFPA 654-2005 06 Prevention of Fire and Dust Explosion from the Manufacturing, Processing, and Handlingof Combustible Particulate Solids [UMC 506.4]
NFPA 853-2006 07 Installation of Stationary Fuel Cell Power Plants [UMC 1601.0]
PPI TR-4, 2004 Recommended Hydrostatic Strengths and Design Stresses for Thermoplastic Pipe and Fittings Compounds
SAE J512-97 Automotive Tube Fittings
SMACNA, 1995 HVAC Duct Construction Standards - Metal and FlexibleAddendum 1, 11/97
SMACNA 1884, 2003 Fibrous Glass Duct Construction Standard
UL 17, 1994 edition 3 Vent or Chimney Connector Dampers for Oil-Fired Appliances
UL 21, 1995 edition 9 LP-Gas Hose
UL 33, 2003 edition 7 Heat Responsive Links for Fire Protection Service
UL 51, 2002 edition 9 Power-Operated Pumps for Anhydrous Ammonia and LP-Gas
UL 80, 2004 edition 11 Steel Tanks for Oil-Burner Fuel
UL 103, 2001 edition 10 Factory-Built Chimneys for Residential Type and Building Heating Appliances
UL 125-1997 edition 6 Valves for Anhydrous Ammonia and LP-Gas (Other than Safety Relief)
UL 127-1996 edition 7 Factory-Built Fireplaces
UL 132, 1997 edition 6 Safety Relief Valves for Anhydrous Ammonia and LP-Gas
UL 144, 1999 edition 7 LP-Gas Regulators
UL 174, 2004 edition 11 Household Electric Storage Tank Water Heaters
UL 180-2003 edition 7 Liquid Level Indicating Gauges for Oil Burner Fuels
UL 181, 1996 edition 10 Factory-Made Air Ducts and Air Connectors
UL 181A, 1994 2005 edition 3 Closure Systems for Use with Rigid Air Ducts and Air Connectors
Item #108
STANDARDS Chapter 17
Standard Number Standard Title [UMC References]
UL 181B, 1995 2005 edition 2 Closure Systems for Use with Flexible Air Ducts and Air Connectors
UL 197, 2003 edition 9 Commercial Electric Cooking Appliances [UMC 513.2.2]
UL 207, 2001 edition 7 Non-Electrical Refrigerant-Containing Components and Accessories
UL 252, 2003 edition 8 Compressed Gas Regulators
UL 268A, 1998 edition 3 Smoke Detectors for Duct Application
UL 296, 2003 edition 10 Oil Burners
UL 300, 1996 2005 edition 3 Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas [UMC 513.2.2]
UL 343, 1997 edition 8 Pumps for Oil-Burning Appliances
UL 352, 19972006 edition 7 8 Constant-Level Oil Valves
UL 353, 1994 edition 5 Limit Controls
UL 378, 1993 2006 edition 3 4 Draft Equipment
UL 391, 1995 edition 3 Solid-Fuel and Combination Fuel Central and Supplementary Furnaces
UL 404, 1997 2005 edition 7 Indicating Pressure Gauges for Compressed Gas Service
UL 412, 2004 edition 4 Refrigeration Unit Coolers
UL 429, 1999 edition 5 Electrically Operated Valves
UL 441, 1996 edition 9 Gas Vents
UL 443, 1995 2006 edition 5 6 Steel Auxilliary Tanks for Oil Burner Fuel
UL 471, 1995 2006 edition 8 9 Commercial Refrigerators and Freezers
UL 525, 2004 edition 7 Flame Arresters
UL 536, 1997 edition 9 Flexible Metallic Hose
UL 555, 1999 2006 edition 6 7 Fire Dampers
UL 555C, 1996 2006 edition 2 3 Ceiling Dampers
UL 555S, 1999 edition 4 Smoke Dampers
UL 565, 1998 edition 5 Liquid Level Gauges and Indicators for Anhydrous Ammonia and LP-Gas
UL 569, 1995 edition 7 Pigtails and Flexible Hose Connectors for LP-Gas
UL 641, 1995 edition 7 Type L Low Temperature Venting Systems
UL 710, 1995 edition 5 Exhaust Hoods for Commercial Cooking Equipment
UL 723, 2003 edition 9 Test for Surface Burning Characteristics of Building Materials [UMC 508.3, 602.2, 605.0(E), 1201.4.1.3]
UL 726, 1995 edition 7 Oil-Fired Boiler Assemblies
UL 727, 1994 2006 edition 8 9 Oil-Fired Central Furnaces
UL 729, 2003 edition 6 Oil-Fired Floor Furnaces
UL 730, 2003 edition 5 Oil-Fired Wall Furnaces
UL 731, 1995 edition 5 Oil-Fired Heater Units
UL 732, 1995 edition 5 Oil-Fired Storage Tank Water Heaters
UL 733, 1993 edition 4 Oil-Fired Water Heaters and Direct-Fired Heaters
Item #108
Standard Number Standard Title [UMC References]
UNIFORM MECHANICAL CODEChapter 17
UL 737, 1996 edition 8 Fireplace Stoves
UL 791, 1993 2006 edition 4 5 Residential Incinerators
UL 795, 1999 2006 edition 5 6 Commercial-Industrial Gas Heating Equipment (Inputs over 400,000 Btu per hour)
UL 834, 2004 edition 5 Electric Water Supply Heating and Power Boilers
UL 842, 1997 edition 8 Valves for Flammable Fluids
UL 858, 1993 2005 edition 15 Household Electric Ranges
UL 867, 2000 edition 4 Electrostatic Air Cleaners
UL 896, 1993 edition 5 Oil-Burning Stoves
UL 900, 2004 edition 7 Air Filter Units
UL 907, 1994 edition 2 Fireplace Accessories
UL 921, 1996 edition 5 Commercial Electric Dishwashers
UL 959, 2001 edition 8 Medium Heat Appliance Factory-Built Chimneys
UL 984, 1996 edition 7 Hermetic Refrigerant Motor Compressors
UL 1026, 1995 edition 4 Electric Household Cooking and Food Serving Appliances
UL 1046, 2000 edition 3 Grease Filters for Exhaust Ducts [UMC 509.1]
UL 1206, 2003 edition 4 Electric Commercial Clothes-Washing Equipment
UL 1240, 1994 2005 edition 3 4 Electric Commercial Clothes-Drying Equipment
UL 1453, 2004 edition 5 Electric Booster and Commercial Storage Tank Water Heaters
UL 1482, 1996 edition 5 Solid-Fuel Type Room Heaters
UL 1738, 1993 edition 2 Venting Systems for Gas-Burning Appliances, Categories II, III, and IV
UL 1746, 1993 2007 edition 2 3 External Corrosion Protection Systems for Steel Underground Storage Tanks
UL 1777, 2004 edition 3 Chimney Liners
UL 1812, 1995 edition 2 Ducted Heat Recovery Ventilators
UL 1815, 2001 edition 3 Nonducted Heat Recovery Ventilators
UL 1820, 2004 edition 4 Fire Test of Pneumatic Tubing for Flame and Smoke Characteristics [UMC 602.2(7)]
UL 1887, 2004 edition 3 Fire Test of Plastic Sprinkler Pipe for Visible Flame and Smoke Characteristics [UMC 602.2(6)]
UL 1963, 1995 2005 edition 2 3 Refrigerant Recovery/ Recycling Equipment
UL 1978, 2002 2005 edition 3 Grease Ducts
UL 1995, 1995 2005 edition 3 Heating and Cooling Equipment
UL 2021, 1997 edition 2 Fixed and Location-Dedicated Electric Room Heaters
UL 2043, 1996 edition 2 Fire Test for Heat and Visible Smoke Release for Discrete Products and Their Accessories Installed in Air Handling Spaces [UMC 602.2(8)]
UL 2157, 1997 edition 2 Electric Clothes Washing Machines and Extractors
UL 2158, 1995 edition 2 Electric Clothes Dryers
Item #108
Standards to be added to Table 17-1; Endorsed by the UMC Chp. 17 Task Group ASHRAE 62.1-2004 Measuring Air-Change Effectiveness ASME B16.20-98 (R04) Metallic Gaskets for Pipe Flanges; Ring-Joint, Spiral –
Wound, and Jacketed ASTM A 254-97 (R02) Copper-Brazed Steel Tubing ASTM B 210-2004 Aluminum and Aluminum-Alloy Drawn Seamless Tubes ASTM B 241-2002 Aluminum and Aluminum-Alloy Seamless Pipe and
Seamless Extruded Tube ASTM D 93-2006 Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester ASTM D 2513-2006a Thermoplastic Gas Pressure Pipe, Tubing, and Fittings ASTM D 3309-96a (R02) Polybutylene (PB) Plastic Hot- and Cold- Water
Distribution Systems ASTM F 876-2005 Crosslinked Polyethylene (PEX) Tubing ASTM F 877-2005 Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-
Water Distribution Systems ASTM F 1282-2006 Polyethylene/Aluminum/ Polyethylene (PE-AL-PE)
Composite Pressure Pipe ASTM F 1807-2005 Metal Insert Fittings Utilizing Copper Crimp Ring for SDR
9 Crosslinked Polyethylene (PEX) Tubing ASTM F 1960-2005 Cold Expansion Fittings with PEX Reinforcing Rings for
Use with Crosslinked Polyethylene (PEX) Tubing ASTM F 1970-2005 Special Engineered Fittings or Appurtenances or Valves for
Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems
ASTM F 1973-2005 Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polymide 11 (PA11) Fuel Gas Distribution Systems
ASTM F 2080-2005 Cold-Expansion Fittings with Metal Compression Sleeves for Crosslinked Polyethylene (PEX) Pipe
ASTM F 2098-2004e1 Stainless Steel Clamps for Securing SDR 9 Crosslinked Polyethylene (PEX) Tubing to Metal Insert Fittings
ASTM F 2159-2005 Plastic Insert Fittings Utilizing a Copper Ring for SDR 9 Crosslinked Polyethylene (PEX) Tubing
ASTM F 2262-2005 Crosslinked Polyethylene/Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) Tubing OD Controlled SDR 9
ASTM F 2434-2005 Metal Insert Fittings Utilizing Copper Crimp Ring for SDR 9 Crosslinked Polyethylene (PEX) Tubing and SDR 9 Crosslinked Polyethylene/Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) Tubing
ASTM F 2509-2006 Field-Assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
CAN/CGSB 3.2-99 Heating Fuel Oil
Item #109
29 CFR 1910.1000 Code of Federal Regulations 49 CFR 191 and 192 Code of Federal Regulations 49 CFR 192.123 Code of Federal Regulations 49 CFR 192.281(e) Code of Federal Regulations 49 CFR 192.283 (b) Code of Federal Regulations EPA Test Method 202-1996 Determination of Condensable Particulate Emissions for
Stationary Sources MSS SP-6-2001 Standard Finishes for Contact Faces of Pipe Flanges and
Connecting-End Flanges of Valves and Fittings NFPA 10-2007 Portable Fire Extinguishers NFPA 12-2005 Carbon Dioxide Extinguishing Systems NFPA 13-2007 Installation of Sprinkler Systems NFPA 17-2002 Dry Chemical Extinguishing Systems NFPA 17A-2002 Wet Chemical Extinguishing Systems NFPA 37-2006 Installation and Use of Stationary Combustion Engines and
Gas Turbines NFPA 80-2007 Fire Doors and Fire Windows NFPA 82-2004 Incinerators and Waste and Linen Handling Systems and
Equipment NFPA 88A-2007 Parking Structures NFPA 90A-2002 Installation of Air-Conditioning and Ventilating Systems NFPA 90B-2006 Installation of Warm Air Heating and Air-Conditioning
Systems NFPA 91-2004 Exhaust Systems for Air Conveying of Vapors, Gases,
Mists, and Noncombustible Particulate Solids NFPA 274-2003 Test Method to Evaluate Fire Performance Characteristics
of Pipe Insulation NFPA 409-2004 Aircraft Hangers NFPA 501A-2005 Fire Safety Criteria for Manufactured Home Installations
Sites and Communities UL 2221, 2001 edition 1 Tests of Fire Resistive Grease Duct Enclosure Assemblies
Item #109
UMC 2009 – August 2007 ROP
SUBMITTER:
Add new text as follows:
TABLE 17–1Standards for Equipment and Materials
Note: This Chapter has been revised and reformatted in its entirety.No arrows or side bars have been used to signify changes.
____________________________________________________________________________________Standard Number Standard Title [UMC References]____________________________________________________________________________________ASTM F 2389–2006 Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems
This proposal provides for an alternate plumbing material. These polypropylene (PP) piping systems are manufactured, tested and listed in accordance with ASTM F 2389, and have been accepted in other model codes in the U.S. and Canada.
SUBSTANTIATION:
RECOMMENDATION:
UMC 2009 Table 17–1
Accept as Submitted
James Paschal
110-
Bodycote
TOTAL ELIGIBLE TO VOTE: 24
VOTING RESULTS: AFFIRMATIVE: 22, NOT RETURNED: 2 T. Nothaft, D. Bixby
COMMITTEE ACTION:
Item #
171
UMC 2009 – August 2007 ROP
SUBMITTER:
Revise Table 17–1 as follows:Delete existing Table 17–1 and keyword table. Replace with Table 17–1 as follows (see attached standards table onpages 172–1 through 172–21).
To correlate with the new UPC Standards table format, recommended by the UPC Standards Task Group, which willadd the application and applicable code sections applying to the standards.
SUBSTANTIATION:
RECOMMENDATION:
UMC 2009 Table 17–1, Chapter 17
Accept as Submitted
John Taecker
111-
Chair, UMC Standards Task Group
TOTAL ELIGIBLE TO VOTE: 24
VOTING RESULTS: AFFIRMATIVE: 22, NOT RETURNED: 2 T. Nothaft, D. Bixby
COMMITTEE ACTION:
Item #
172
Standard Number Standard Title [UMC References] Key Word Application Referenced SectionsACCA Manual D-2002 Residential Duct Systems Ducts 113.2, 305.1, 403.1, 503.1, 505.2, 601.2, 602.4, 606.1,
Table 6-2-P-1, 924.2 and A.6.202
ACCA Manual J-2003 Residential Load Calculations Ducts 113.2, 210.0 “Heating Degree Day”, 403.1, 403.5.1 601.2, Table 6-2-A, 1201.3.5.3, 601.2, A.6.504 (F) and C.4.0.
ACCA Manual N Commercial Load Calculation Ducts 113.2, 210.0 “Heating Degree Day”, 403.1, 403.5.1 601.2, Table 6-2-A, 1201.3.5.3, 601.2, A.6.504(F) and C.4.0.
ACCA Manual Q Low Pressure Low Velocity Duct Systems Design Ducts 203.0 “Air Conditioned”, Table 4-1, 601.2, 605.0(E) and 1002.0(7).
ANSI B1.20.3-1976 (R2003)
Dryseal Pipe Threads (Inch)
ANSI Z21.23b-20005 Addenda Z21.23a 2003
Gas Appliance Thermostats Thermostats, 912.1(C).
ANSI *CSA Z21.42a-2004 1997 (R2002) 2004
Gas-Fired Illuminating Appliances (same as ANSI Z21.42a-04)
Illuminating appliances 203 “appliance” and Table 13-1.
ANSI Z21.45 1995 [D] Flexible Connectors for Other Than All Metal Construction for Gas Appliances.
Appliance connectors, Connectors, Flexible connectors
Table 17-01
ANSI *CSA Z21.61-1983 (R2004)
Gas-Fired Toilets (same as ANSI Z21.61-83) Toilets 926.0
ANSI *CSA Z21.71a-2005 (R2002)
Automatic Intermittent Ignition Systems for Field Installation (same as ANSI Z21.71a-05)
Automatic Pilot Ignition, Pilot Ignition Systems
1004.9 “Definition” and Table 10-3.
ANSI Z21.88 2002 *CSA 2.33-2005 Addenda Z21.88a-2003
Vented Gas Fireplace Heaters (same as ANSI Z21.88-05)
Fire Place Heaters 802.5.8.
ANSI Z223.1-99 National Fuel Gas Code (same as NFPA 54, see later comments)
Fuel gas code Chapters 8, 9, 13, Table 17-1 and Appendix B
CHAPTER 17
STANDARDSTABLE 17-1
Standards for Equipment and Materials
*ANSI approved standard
172-1
Item #111
ANSI *CSA Z83.18a-2005 Addenda Z83.18a 2001 Addenda Z83.18b 2003
Recirculating Direct Gas-Fired Industrial Air Heaters [UMC 910.1] (same as ANSI Z83.18a-05)
air heaters, industrial heaters, recirculating, non-recirculating, recirculating heaters
Section 910.1, Staff to update
ANSI 1010 2002 UL 399-1993 edition 6
Drinking Fountains and Self-Contained, Mechanically Refrigerated Drinking Water Coolers.
Drinking fountains, Water coolers
Table 17-1
ARI 700-99 Specification for Fluorocarbon Refrigerant Refrigerants 1102.0
ASCE 25-1999 Earthquake Actuated Automatic Gas Shutoff Devices
Earthquake valves, Shutoff valves
Ch. 13
ASHRAE 129-1997 (RA 2002)
Measuring Air-Change Effectiveness Used as an alternate sizing value.
Table 4-2
ASHRAE 15-2004 Safety Refrigeration Systems Refrigerations systems Ch. 11
ASHRAE 34-2004 Designation and Safety Classification of Refrigerants
Refrigeration classifications
1102.0, 1103.0 and 1133.0 where refrigerants are discussed
ASHRAE 62.1-2004 Ventilation for Acceptable Indoor Air Quality, Addenda h,i,k,n,o,r,t,u,v,x,z,ab,ad,ae,and,af [UMC 403.4.2]
Indoor air quality, Ventation
Ch. 4
ASHRAE Climatic Conditions
ASHRAE Handbook - Fundamentals, Chapter 27, Table 1A & B, for the US 2001
Design Ch. 4, Ch. 6
ASHRAE Handbook Fundamentals, Climatic Conditions for the United States; Chapter 27, Table 1A and B, 2001
Climatic conditions Ch. 4
ASHRAE Volume 1980 Panel Heating Systems Design 1202.0 and 1203.0.
ANSI *ASME 13.1-1996 Scheme for the Identification of Piping Systems Piping 1111.8, 1112.4, 1201.2.1.14, 1309.6.5, 1309.7.1 and UMC Standard 6-5 “Closures”.
ASME A112.18.6 - 2003 Flexible Water Connectors Connectors, Flexible connectors, Water connectors
Table 17-1
ASME A112.18.6- 2003 Flexible Water Connectors Product; Connectors, Flexible connectors, Water connectors
Table 17-1
ASME A112.20.1-2004 Qualification of Installers of High Purity Piping Systems
Certification: High purity piping, Installers
1401.0
ASME A112.4.1-93 (R2002)
Water Heater Relief Valve Drain Tubes Drain tubes, Relief Valve drains, Water heater drains
Ch. 12, Ch. 14
*ANSI approved standard
172-2
Item #111
ASME B1.20.1-1998 (R2006)
Pipe Threads, General Purpose, Inch [UMC 1309.5.7(A)]
Threads Section 1309.5.7(A) and 1201.2.2.1
ANSI *ASME B1.20.3-76 (R2003)
Dryseal Pipe Threads, Inch Joints Threads 1309.5.8 (6)
ASME B16.1-1998 Cast-Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, 250, and 800 Piping, Ferrous [UMC 1309.5.10]
Cast fittings, Cast iron fittings, Copper alloy fittings, Flanged fittings, Pressure fittings, Solder fittings
1309.5.10
ASME B16.18-2001 Cast Copper Alloy Solder Joint Pressure Fittings Cast fittings, Copper alloy fittings, Pressure fittings, Solder fittings
Ch. 12
ASME B16.20-2000 (R2004)
Metallic Gaskets for Pipe Flanges; Ring-Joint, Spiral-Wound, and Jacketed
1309.5.10
ASME B16.22-2001 (R2005)
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
Copper alloy fittings, Pressure fittings, Solder fittings, Wrought fittings
1201.2.1.4.2.
ASME B16.23-2002 Cast Copper Alloy Solder Joint Drainage Fittings Cast fittings, Copper alloy fittings, Drainage fittings, Solder fittings
310.0
ASME B16.24-2001 Cast Copper Alloy Pipe Flanged Fittings Classes 150, 300, 400, 600, 900, 1500, and 2500
Cast fittings, Copper alloy fittings, Flanged fittings
111.7, 1309.5.8.1 and “1309.5.10”.
ASME B16.26-1988 Cast Copper Alloy Fittings for Flared Copper Tubes
Cast fittings, Copper alloy, Flared tube fittings
Ch. 12
ASME B16.29-2001 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings
Copper alloy fittings, Drainage fittings, Solder fittings, Wrought fittings
310.0
ASME B16.33-2002 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psi (Sizes 1/2 NPS - 2 NPS 24)
Gas valve, Manual valve
1311.9
ASME B16.38 1985 (R1994) [D]
Large Metallic Valves for Gas Distribution (Manually Operated, NPS 2-1/2 to 12, 125 psig/Maximum)
Gas valve, Manual valve
*ANSI approved standard
172-3
Item #111
ASME B16.50-2001 Wrought Copper and Wrought Copper Alloy Braze-Joint Pressure Fittings
Braze joint fittings, Copper alloy fittings, Copper fittings, Pressure fittings, Wrought fittings
CH. 12
ASME B31.5-2001 Refrigeration Piping Refrigeration Piping, Piping
1110.2 and 1110.3.
ASME B36.10M-2004 Welded and Seamless Wrought Steel Pipe [UMC 1309.5.2.2]
Seamless pipe, Steel pipe, Welded pipe, Wrought steel pipe
Section 1309.5.2.2
ASME Section IV Rules for Construction of Heating Boilers Boiler construction, Heating boilers
1002.0.
ASME Section VIII Rules for Construction of Pressure Vessels Pressure vessel construction, Pressure vessels
Section 1333.6.2 and 1002.0
ASSE 1005 1999 [D] Water Heater Drain Valves. Drain valves, Water heater drain valves
Table 17-1
ASTM A 53- 200206a Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded, and Seamless [UMC 1309.5.2.2(2)]
Black steel pipe, Seamless steel pipe, Steel pipe, Welded steel pipe, Zinc coated steel pipe
Section 1309.5.2.2(2) and Table 17-1
ASTM A 254-97(R2002) Copper-Brazed Steel Tubing Section 1309.5.3.1
ASTM A 312M-200306 Seamless, and Welded and Heavy Cold Worked of Austenitic Stainless Steel Pipes
Carbon steel fittings, Pipe fittings, Pipe nipples, Stainless steel fittings
Ch.12, Ch. 14
ASTM A539-99 Standard Specification for Electric-Resistance-Welded Coiled Steel Tubing for Gas and Fuel Oil Lines.
Product Section 1309.5.3.1
ASTM A 653M-2006 Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
Alloyed coating, Bake hardenable steel, High strength low alloy, Minimized spangle coating, Sheet steel, Spangle, Steel, Steel sheet, Structural steel
209.0 (Galvanized Steel), Appendix A
*ANSI approved standard
172-4
Item #111
ASTM A 733-03 Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples
Carbon steel fittings, Pipe coatings, Pipe nipples, Stainless steel fittings
Ch. 12, Ch. 14
ASTM A 861-2004 High-Silicon Iron Pipe and Fittings (Note 1) corrosion resistant, fittings, High-silicon iron, hubless, Hub/plain-end, No-hub
Ch. 12, Ch. 14
ASTM B 241/241M-02 Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
Product Section 1309.5.2.4
ASTM B 280-2003 Seamless Copper Tube for Air Conditioning and Refrigeration Field Service [UMC 1329.5.3.2]
Air conditioning tube, Copper tube, Field service tube, Refrigeration tube, Seamless copper tube
Ch. 11 and Section 1309.5.3.2
ASTM B 302-2002 Threadless Copper Pipe (TP) Brazed-joint pipe fittings, Copper pipe, Threadless copper pipe, Threadless pipe, Threadless pipe (TP)
Ch. 12, Ch. 13
ASTM B 306-2002 Copper Drainage Tube (DWV) Copper tube, Drainage tube
310,0
ASTM B 32-2004 Solder Metal Bar, Flux, Flux cored solder, Ingot, Lead-silver alloys, Lead-tin alloys, Lead-tin-silver alloys, Powder, Ribbon
1201.2.3.7.
ASTM B 42-2002e1 Seamless Copper Pipe, Standard Sizes Copper pipe, Extra strong, Regular, Standard sizes
Ch. 12, Ch. 13
ASTM B 43-98E1 (R2004) Seamless Red Brass Pipe, Standard Sizes Cooper alloy UNS No. C23000, Red brass pipe
1111,7 and 1309.5.2.5
ASTM B 75-2002 Seamless Copper Tube Seamless copper tube, Seamless tube, Tube
Ch.12, Ch. 13
*ANSI approved standard
172-5
Item #111
ASTM B 88-2003 Seamless Copper Water Tube, (K, L, M) [UMC 1309.5.3.2]
Copper tube, Seamless, UNS No. C10200, UNS No. C12000, UNS No. C12200, Water tube
Ch. 12, and Section 1309.5.3.2
ASTM B 135-02, ASTM B 135M-00 (2006)
Seamless Brass Tube Seamless brass tube Ch. 12, Ch. 13
ASTM B 210-04/B210M-05
Aluminum and Aluminum-Alloy Drawn Seamless Tubes/Aluminum and Aluminum-Alloy Drawn Seamless Tubes Metric
Product Section 1309.5.3.3
ASTM B 370-19982003 Copper Sheet and Strip for Building Construction Building construction, Coils for building construction, Copper sheet, Copper strip, Downspouts, Flashing, Gutters, Roofing, Sheet/strip in flat lengths
508.1.1.
ASTM B 447-2002 Welded Copper Tube Copper tube, Copper welded tube, Welded tube
Ch. 12, Ch. 13 and Ch. 14
ASTM B 584 2000 [D] Copper Alloy Sand Casting for General Applications (Note 5)
Copper-base alloy castings
Table 17-1
ASTM B 587-1997 (R2003) 2006
Welded Brass Tube Brass tube, Welded brass tube
Ch. 12, Ch.13, Ch. 14
ASTM B 687-99 (R2005) e1 Brass, Copper, and Chromium-Plated Pipe Nipples
Chromium plating, Copper, Copper alloy fittings, Em tube, Pipe nipples
1312.7
ASTM B 813-00e1 Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
Aggressiveness test, Copper and copper alloys, Corrosiveness, Flushing, Liquid and plaste fluxes, Resistivity, Sodering, Spreading factor, Tarnish
1201.2.1.7
*ANSI approved standard
172-6
Item #111
ASTM B 828-02 Standard Practice for Making Capillary Joints in Copper and Copper Alloy Tube and Fittings
Assembly, Capillary, Cleaning, Copper, Corrosivity, Fittings, Flux
1201.2.3.7.
ASTM C 411- 1997 2005 Hot-Surface Performance of High Temperature Thermal Insulation [UMC 605.0, 1201.4.1.3]
Block board, Cracking, Delamination, Hot-surface performance, pipe thermal insulation, Surface analysis-building, Temperature tests-insulation, Thermal insulating materials
Sections 605.0(E), 1201.4.1.3
ASTM C 518-2004 Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
Certification: Calibration, Error analysis, Heat flow meter apparatus, Heat flux, Instrument verificatyion, Thermal conductivity, Thermal resistance, Thermal testing, Tunnel Test
ASTM D 93 - 1999 2006 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
Certification: 503.3 refers to Fire Code Standards
ASTM D 2513-2006a Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
Product Sections 1309.5.4 and 1329.3
ASTM D 3309-96a (R2002)
Standard Specification for Polybutylene (PB) Plastic Hot-and Cold-Water Distribution Systems.
Product Section 1201.3
ASTM E 84- 2004 2006 Surface Burning Characteristics of Building Materials [UMC 602.2, 605.0, 1201.4.1.3]
Certification: 25 foot tunnel, Flame spread, Flame spread index, Smoke developed, Smoke developed index, Steel sheet, Surface burning test
Sections 602.2, 605.0(E), 1201.4.1.3
*ANSI approved standard
172-7
Item #111
ASTM E 814-06 Fire Tests of Through Penetration Fire Stops Certification: Fire testing-building materials, Fire testing-hose stream test, Structural analysis/applications
608.9 and 928.1 (c).
ASTM F 876-05 Crosslinked Polyethylene (PEX) Tubing Section 1204.4
ASTM F 877-05 Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems
Section 1204.4
ASTM F 1961-02a Metal Mechanical Cold Flare Compression Fittings with Disc Springs for Crosslinked Polyethylene (PEX) Tubing
Cold and hot water distribution, Cold expansion insert fittings, Crosslinked polyethylene, PEX
1201.4.1.1 and 1201.4.2.3.
ASTM F 1281- 2003 2005 Crosslinked Polyethylene/ Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe [UMC 1201.5, 1201.5.1.1, 1201.5.2]
Composite, Crosslinked PE, PEX-AL-PEX, Pipe, Pressure
Sections 1201.5, 1201.5.1.1, 1201.5.2
ASTM F 1807-2005 Metal Insert Fittings Utilizing Copper Crimp Ring for SDR 9 Crosslinked polyethylene (PEX) Tubing
ASTM F 1282-2006 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
ASTM F 1960-2006 Cold Expansion Fittings with PEX Reinforcing Rings for Use with Crosslinked Polyethylene (PEX) Tubing
ASTM F 1970-2005 Special Engineered Fittings or Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) SystemsASTM F 1973-2005 Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polymide 11 9PA11) Fuel Gas Distribution SystemsASTM F 2080-2005 Cold-Expansion fittings with Metal Compression Sleeves for Crosslinked Polyethylene (PEX) Pipe
ASTM E 2231-2002e1 Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics [UMC 605.0, 1201.4.1.3]
Certification: IEEE, Insulation, Pipe, Preparation
Sections 605.0(E), 1201.4.1.3
*ANSI approved standard
Item #111
172-8
ASTM F 2098-2004e1 Stainless Steel Clamps for Securing SDR 9 Crosslinked
ASTM F 2158-2001 Residential Central-Vacuum Tube and Fittings Central vacuum, Fittings, PVC, Tube
506.1 (3).
ASTM F 2159-2005 Plastic Insert Fittings Uilizing a Copper Ring for SDR 9 Crosslinked Polyethylene (PEX) Tubing
ASTM F 2262-2005 Crosslinked Polyethylene/ Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) Tubing OD Controlled SDR 9
ASTM F 2434-2005 Metal Insert Fittings Utilizing Copper Crimp Ring for SDR 9 Crosslinked Polyethylene (PEX) Tubing and SDR 9 Crosslinked Polyethylene/ Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) TubingASTM F 2509-2006 Field-Assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
AWS A5.8M/A5.8: 2004 Specification for Filler Metals for Brazing and Braze Welding
1205.2, 1309.5.8.1 and 1309.5.8.2.
AWWA C151 Ductile-Iron Pipe, Centrifugally Cast, for Water (same as ANSI A21.51-91)
Water Pipe 1201.2.1.1., Table 17-1
AWWA C110 Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1200 mm), for Water and Other Liquids (same as ANSI A21.10-98)
1201.2.1.1., Table 17-1
AWWA C203-02 Coal-Tar Protective Coatings and Linings for Steel Water Pipelines - Enamel and Tape - Hot-Applied -
Pipe coatings, Pipe linings
1201.2.1.6 and 1309.5.6.
AWWA C500-2002 Gate Valves for Water and Sewerage Systems Valves
Gate valves Ch. 14
CAN/CGSB 3.2-99 Heating Fuel Oil Fuel oil Appendix C.1.0 “Definitions”.
CFR 29, 1910.1000 Code of Federal Regulations Table 11-1
CFR 49, 191 and 192 Code of Federal Regulations Sections 1324.0 and 1325.0
CFR 49, 192.123 Code of Federal Regulations Sections 1329.3 and 1330.2.1
CFR 49, 192.281(e) Code of Federal Regulations Section 1309.5.4.2
CFR 49, 192.283(b) Code of Federal Regulations Section 1309.5.4.2
*ANSI approved standard
172-9
Item #111
ASTM E 814-06 Fire Tests of Through Penetration Fire Stops Certification: Fire testing-building materials, Fire testing-hose stream test, Structural analysis/applications
608.9 and 928.1 (c).
ASTM F 876-05 Crosslinked Polyethylene (PEX) Tubing Section 1204.4
ASTM F 877-05 Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems
Section 1204.4
ASTM F 1961-02a Metal Mechanical Cold Flare Compression Fittings with Disc Springs for Crosslinked Polyethylene (PEX) Tubing
Cold and hot water distribution, Cold expansion insert fittings, Crosslinked polyethylene, PEX
1201.4.1.1 and 1201.4.2.3.
ASTM F 1281- 2003 2005 Crosslinked Polyethylene/ Aluminum/ Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe [UMC 1201.5, 1201.5.1.1, 1201.5.2]
Composite, Crosslinked PE, PEX-AL-PEX, Pipe, Pressure
Sections 1201.5, 1201.5.1.1, 1201.5.2
ASTM F 1807-2005 Metal Insert Fittings Utilizing Copper Crimp Ring for SDR 9 Crosslinked polyethylene (PEX) Tubing
ASTM F 1282-2006 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
ASTM F 1960-2006 Cold Expansion Fittings with PEX Reinforcing Rings for Use with Crosslinked Polyethylene (PEX) Tubing
ASTM F 1970-2005 Special Engineered Fittings or Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) SystemsASTM F 1973-2005 Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polymide 11 9PA11) Fuel Gas Distribution SystemsASTM F 2080-2005 Cold-Expansion fittings with Metal Compression Sleeves for Crosslinked Polyethylene (PEX) Pipe
ASTM E 2231-2002e1 Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics [UMC 605.0, 1201.4.1.3]
Certification: IEEE, Insulation, Pipe, Preparation
Sections 605.0(E), 1201.4.1.3
*ANSI approved standard
Item #111
172-10
ANSI Z83.20 2001 *CSA 2.34-2001 (R05), CSA 2.34a-2003, CSA 2.34b-2004 Addenda Z83.20a 2002 Addenda Z83.20b 2004
Gas-Fired Tube Type and Low Intensity Infrared Heaters (same as ANSI Z83.20b-04)
Infrared heaters, Low intensity heaters
919.0
ANSI Z83.19a 2002 *CSA 2.35a-2002
Gas-Fired High Intensity Infrared Heaters (same as ANSI Z83.19a-02)
High intensity heaters, infrared heaters
919.0
ANSI Z83.8 2002 *CSA 2.6-2006 Addenda Z83.8a 2003
Gas Unit Heaters and Gas-Fired Duct Furnaces (same as ANSI Z83.8-06)
Product Sections 901.0 and 911.1(A).
CSA 2.7-M98 Domestic Gas Conversion Burners Conversion Burners, Domestic, Gas Burners
Sections C.4.0, 802.10.2.4 and 802.12.1
ANSI Z83.4 1999 *CSA 3.7-2003, CSA 3.7a-2004, CSA 3.7b-M992006 Addenda Z83.4a 2001 CSA 3.7a 2001
Non-Recirculating Direct Gas-Fired Industrial Air Heaters [UMC 909.1] (same as ANSI Z83.4b-06)
Air heaters, Non-recirculating, Non-recirculating heaters,
Section 909.0 and Table 17-1
ANSI Z21.10.1 2004 *CSA 4.1ab-02 2006
Gas Water Heaters, Volume I, Water Heaters with Input Ratings of 75,000 Btu per Hour or Less (same as ANSI Z21.10.1b-06)
Gas Water Heaters 225.0, 517.1.2, 802.2.2.5, 803.1.8.1, and Table 13-1.
ANSI Z21.10.3 2004 *CSA 4.3-2004
Gas Water Heaters, Volume III, Water Heaters with Input Ratings Above 75,000 Btu per Hour, Circulating and Instantaneous Water Heaters (same as ANSI Z21.10.3-04)
Gas Water Heaters 225.0, 517.1.2, 802.2.2.5, 803.1.8.1, and Table 13-1.
ANSI Z21.22 1999 (R2003) *CSA 4.4-M99 (R04), CSA 4.4a-00 (R04), CSA 4.4b-01 (R04) Addenda Z21.22a 2000 Addenda Z21.22b 2004
Relief Valves for Hot Water Supply Systems (same as ANSI Z21.22b-03)
Hot Water, Pressure Relief, Relief Valves, Valves
802.8.4, in 904.6 “ASME” is referenced, 1007.0, 1011.2, and 1206.0
ANSI Z21.56 2001 *CSA 4.7-2006 Addenda Z21.56a 2003
Gas-Fired Pool Heaters (same as ANSI Z21.56 2006)
Gas fired heaters, Pool heaters, Spa heaters
922.0
ANSI Z21.13 2004 *CSA 4.9-2004, CSA 4.9a-200205
Gas-Fired Low Pressure Steam and Hot Water Boilers (same as ANSI Z21.13a-05)
Gas Fired Boilers, Hot Water Boilers, Low Pressure Boilers, Steam Boilers
214.0 “Definitions”, 304.1, Table 3-1, 904.1.1, 904.2 (E), 1002.0 (1), 1004.12 and Table 13-1.
*ANSI approved standard
172-11
Item #111
ANSI Z21.24 2004 *CSA 6.10-2001, CSA 6.10a-2002, CSA 6.10b-2003 Addenda Z21.24a 2002 Addenda Z21.24b 2003
Connectors for Gas Appliances (same as ANSI Z21.24b-03) [UMC 1312.1(3)]
Connectors, Gas Connectors,
Section 1312.1(3) and Tables 3-4 and 3-5, 1333.5.1 additional standard reference later in this chart ANSI Z21.69.
ANSI Z21.69 2002 *CSA 6.16-2002, CSA 6.16a-2003, CSA 6.16b-200206 Addenda Z21.69a 2003/ CGA 6.16a Addenda Z21.69b 2001/CGA 6.16b
Connectors for Moveable Gas Appliances [UMC 303.1(5), 1312.1(6)] (same as ANSI Z21.69b-06)
Appliance connectors, Connectors
Sections 303.1(5), 1312.1(6) and Table 17-1
ANSI Z21.80 2003 *CSA 6.22-2003, CSA 6.22a-M972005
Line Pressure Regulators (same as ANSI Z21.80a-05) [UMC 1309.7.2, 1309.9.7.5(A)]
Pressure Regulators, Regulators
Sections 1309.7.2, 1309.7.5(A) and Table 17-1
CSA 6.26-2005 Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST) Fuel Gas [UMC 1309.5.3.4] (same as ANSI LC-1)
CSST, Fuel gas tubing, Stainless steel tubing
Section 1309.5.3.4
ANSI Z21.18 2000 *CSA 6.3-00(R06), CSA 6.3a-2001, CSA 6.3b-2005 Addenda Z21.18a 2001
Gas Appliance Pressure Regulators (same as ANSI Z21.18b-05)
Appliance Regulators, Gas Refrigerators, Pressure Regulators
Sections 917.5, 1309.7 (B), 1310.0 (1) and (2).
ANSI Z21.21 2000 *CSA 6.5-2005 Addenda Z21.21a 2001
Automatic Valves for Gas Appliances (same as ANSI Z21.21-05)
Appliance valves, Automatic, Gas Valves, Valves
Sections 917.2 B (3) and B.4.0.
ANSI Z21.35 1995 (R2002) *CSA 6.8-2005 Addenda Z21.35a 2000 (R2002) Addenda Z21.35b (R2002)
Pilot Gas Filters (same as ANSI Z21.35-05) Filters, Pilot Filters Ch. 13
ANSI Z21.41-05 *CSA 6.9-2003, CSA 6.9A-2005
Quick-Disconnect Devices for Use with Fuel Gas (same as ANSI Z21.41a-05)
Quick disconnect 303.2 (B) and 1303.7.
ANSI Z21.5.1 2002 *CSA A7.1b-2005 ,ANSI Z21.5.1a 2003 Addenda Z21.5.1a 2002
Gas Clothes Dryers - Volume I, Type I (same as ANSI Z21.5.1b-05)
Clothes Dryers, Gas Table 3-4 and 3-5, 504.3, 701.1.1, 701.1.4, 802.2.2.4, 905.0, 1312.7.
ANSI Z21.5.2 2001 *CSA 7.2-2005 ANSI Z21.5.2a 2003 Addenda Z21.5.2a 2003
Gas Clothes Dryers - Volume II Type 2 (same as ANSI Z21.5.2-05)
Clothes Dryers, Gas Table 3-4 and 3-5, 504.3 701.1.4,905.0, 1312.7
172-12
Item #111
ANSI Z21.54 2002 *CSA 8.4-2002, CSA 8.4A-2006
Gas Hose Connectors for Portable Outdoor Gas-Fired Appliances (same as ANSI Z21.54a-06)
Appliance Connectors, Gas Connectors, Hose Connectors, Indirect Water heaters, Pool heaters, Portable appliance connectors
303.1 (4), 303.2 (B), 1312.1 (5) and 1312.2 (B).
ANSI Z21.83 1998 *CSA America FCI-2004
Fuel Cell Power Plants [UMC 1601.0] Fuel Cell Power Plants Section 1601.0 and Table 17-1
ANSI Z21.17 1998 *CSA 2.7 98 (R2004)
Installation of Domestic Gas Conversion Burners [UMC 906.0] (same as ANSI Z21.17-98)
Conversion Burner Installation, Gas Burners
Section 906.0, C.4.0, 802.10.2.4 and 802.12.1
CSA-F379.1-88 (R1999) Solar Domestic Hot Water Systems (Liquid to Liquid Heat Transfer)
Solar heating systems 1206.0 and Chapter 15.
ANSI *CSA Z21.20-2000 Addenda Z21.20a 2000 Addenda Z21.20b 2001
Automatic Gas Ignition Systems and Components (same as ANSI Z21.20b-01)
Automatic ignition, Gas ignition, ignition
917.1, 917.2 B (3) and B.4.0.
ANSI *CSA Z21.1-200005 Addendum Z21.1a 2003
Household Gas Cooking Appliances Household Cooking Appliances, Gas Fired
307.1, Ch. 13, Ch. 9
ANSI *CSA Z21.11.2b- 200204 Addenda Z21.11.2a 2003
Gas-Fired Unvented Room Heaters, Volume II (same asa ANSI Z21.11.2b-04)
Room Heaters, Unvented Heaters
924.1.1
ANSI *CSA Z21.12-199094 (R2000) addenda Z21.12a 1993 (R2000) Addenda Z21.12b 1994 (R2000)
Draft Hoods (same as ANSI Z21.12-94) Draft Hoods, Hoods Sections B.6.0, 205.0 “Combustion Air”, 206.0 “Draft Hood”, Table 3-3, Table 5-3, 701.1.3, 802.2.2.5, Table 8-1, 802.5, 802.6, 802.7, Table 8-2, 802.10, 802.12, 803.1, 803.2, Tables 8-9 and 8-14, 904.2 (G), 908.1 (B), 926.2 A (1) and B (1), 922.2 (A), 913.0, 911.4, 911.1 (a), Table 9-1.
EPA 202-1996 Determination of Condensable Particulate Emissions for Stationary Sources
516.2.7
IAPMO IS 13-2006 Installation Protectively Coated Pipe Pipe coatings 1311.1.3
IAPMO PS 120-2004 Flashing and Stand Combination for Air Conditioning Units (Residential or Commercial Unit Curb)
air conditioning flashing stand
911.2 and 1106.2.
IAPMO PS 33-2006 Flexible PVC Hose for Pools, Hot Tubs, Spas and Jetted Bathtubs
Flexible hose, Hose, PVC hose
Table 17-1
IAS 1-91 U.S. Requirements for Indirect Water Heaters for Use With External Heat Source
Indirect water heaters 225.0, 517.1.2, 802.2.2.5, 803.1.8.1, and Table 13-1
*ANSI approved standard
172-13
Item #111
I-B-R 1st Edition Aug, 2002
Rating Procedure for Heating Boilers Certification Ch. 10
ISO Guide 65:1996 General Requirements for Bodies Operating Product Certification Systems
Certification: Certification
217 0 (Listing Agency), Ch.3
MSS SP-104-03 Wrought Copper Solder Joint Pressure Fittings Pressure fittings, Solder fittings, Wrought copper fittings
Ch. 12, Ch. 13, Ch. 14
MSS SP-106-03 Cast Copper Alloy Flanges and Flanged Fittings, Class 125, 150, and 300
Cast copper alloy fittings, Copper alloy fittings, Flanged fittings
1111.7 and 1309.5.8.1.
MSS SP-58-02 Pipe Hangers and Supports - Materials, Design, and Manufacture [UMC 1311.2.6(A)]
Pipe hangers, Pipe supports
Section 1311.2.6(A) and Table 17-1
MSS SP-6-2001 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings
Butterfly valves, Pipe hangers, Pipe supports, Valves
Section 1309.5.10
MSS SP-67-2002a Butterfly Valves Butterfly valves, Valves Ch. 12, Ch. 13, Ch. 14
MSS SP-69-2003 Pipe Hangers and Supports - Selection and Application
Pipe hangers, Pipe supports
1311.2.6(A).
MSS sp 73 03 [D] Brazing Joints for Wrought and Cast Copper Alloy Solder Joint Pressure Fittings.
MSS SP-80-03 Bronze Gate-Globe, Angle, and Check Valves Angle valves, Bronze valves, Check valves, Gate valves, Globe valves, Valves
1309.8.2
MSS SP-89-2003 Pipe Hangers and Supports - Fabrication and Installation Practices
Installing pipe hanger, Installing piping supports
Ch. 12, Ch. 14, 1311.2.6(A).
MSS SP-109-1997 (R2006) Welded Fabricated Copper Solder Joint Pressure Fittings
Copper fittings, Fabricated fittings, Pressure fittings, Solder fittings, Welded pipe
Ch. 12, Ch. 13, Ch. 14
NFPA 10-2007 Portable Fire Extinguishers Fire extinguishing 513.10.1
NFPA 12 - 2005 Carbon Dioxide Extinguishing Systems Fire extinguishing 513.2.2.1
*ANSI approved standard
172-14
Item #111
NFPA 13-2007 Installation of Sprinkler Systems Fire extinguishing 513.2.2.1
NFPA 17-2002 Dry Chemical Extinguishing Systems Fire extinguishing 513.2.2.1
NFPA 17A-2002 Wet Chemical Extinguishing Systems Fire extinguishing 513.2.2.1
NFPA 30-2003 Flammable and Combustible Liquids Code [UMC 204.0]
Combustible liquids, Flammable liquids
Section 204.0 and Table 17-1
NFPA 31-2006 Installation of Oil Burning Equipment [UMC 302.3, 1020.0, 1302.0]
Oil burning equipment Sections 302.3, 1019.0, 1302.0 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2 1335.3 and Table 17-1
NFPA 37-2006 Installation and Use of Stationary Combustion Engines and Gas Turbines
Generators 925.0
NFPA 52-2005 Compressed Natural Gas (CNG) Vehicular Fuel Systems
CNG vehicle fuel systems,
NFPA 54-200506 /ANSI Z223.1
National Fuel Gas Code (same as ANSI Z223.1) [UMC 303.3(D), 516.2.1, 1309.7.5(D), 1311.4, 1311.4.1]
Fuel gas code Sections 516.2.1, 1309.7.5(1), 1311.4, 1311.4.1
NFPA 58-2004 Liquefied Petroleum Gas Code [UMC 516.2.1, 1309.5.4.3, 1309.5.9(D), 1313.0]
LPG code Sections 516.2.1, 1309.5.4.3, 1309.5.9(D), 1313.0
NFPA 69-2002 Explosion Prevention Systems Explosion prevention 505.1.2.
NFPA 70-2005 National Electrical Code [UMC 511.6, 512.2.5, 516.2.5, 516.2.7(D), 602.2(5), 1311.12.5(5)]
Electrical Code Sections 511.1.6, 512.2.5, 516.2.5, 516.2.7(D), 602.2(5), 1311.15(A), 1311.12.5(B)
NFPA 80 - 2007 Fire Doors and Fire Windows Fire doors 510.7.5
NFPA 82-2004 Standard on Incinerators and Waste and Linen Handling Systems and Equipment
Incinerator shutes 918.0
NFPA 85-2004 Boiler and Combustion Systems Hazard Code [UMC 1002.0(9), 1020.0]
Boiler hazard code, Fuel cell power plants, Fuel cells
Sections 1002.0(9), 1019.0, Table 10-3
NFPA 88A-2007 Parking Structures Building 911.8.1
NFPA 90A-2002 the Installation of Air-Conditioning and Ventilating Systems
HVAC 904.7 (A), Ch. 6
NFPA 90B-2006 the Installation of Warm Air Heating and Air-Conditioning Systems
HVAC 904.7 (a), Ch. 6
*ANSI approved standard
172-15
Item #111
NFPA 91 - 2004 Exhaust Systems for Air Conveying of Vapors, Gases, Mists, and Noncombustible Particulate Solids
Product conveying ducts
506.5.4
NFPA 96-2004 Ventilation Control and Fire Protection of Commercial Cooking Operations
Commercial cooking Ch. 5, Part II
NFPA 211-2003 Chimneys, Fireplaces, Vents, and Solid Fuel Burning Appliances [UMC 517.7.1, 517.7.2, 517.7.3, 801.1, 801.2, 802.5.1.2, 802.5.1.3, 802.5.4]
Chimneys, Fireplaces, Solid fuel appliances
Sections 517.7.1, 517.7.2, 517.7.3, 801.1, 801.2, 802.5.1.2, 802.5.1.3, 802.5.4
NFPA 255-2005 Method of Test of Burning Characteristics of Building Materials [UMC 602.2, 605.0, 1201.4.1.3]
Certification: Surface burning test (ASTM E84 and UL 723)
Sections 602.2, 605.0, 1201.4.1.3
NFPA 262-2006 Flame Travel and Smoke of Wires and Cables for Use in Air-Handling Spaces [UMC 602.2(5)]
Certification: Surface burning test, wire, cable
Section 602.2(5)
NFPA 274-03 Standard Test Method to Evaluate Fire Performance Characteristics of Pipe Insulation.
Pipe insulation Section 1201.5
NFPA 409-2004 Standard on Aircraft Hangars Building 911.9
NFPA 501A-2003 Fire Safety Criteria for Manufactured Home Installations Sites and Communities
Building Section 1325.0
NFPA 654-2005 Prevention of Fire and Dust Explosion from the Manufacturing, Processing, and Handling of Combustible Particulate Solids [UMC 506.4]
Dust explosion prevention, Gutters
Sections 506.4 and Table 17-1
NFPA 853-2006 Installation of Stationary Fuel Cell Power Plants [UMC 1601.0]
Fuel cell power plants, Fuel cells
Section 1601.0 and Table 17-1
PPI TR-4, 2004 Recommended Hydrostatic Strengths and Design Stresses for Thermoplastic Pipe and Fittings Compounds
Certification: Pipe and fittings compounds, Thermoplastic compounds
Ch. 12, Ch. 14
SAE J512-97 Automotive Tube Fittings Tube fittings
SMACN, 1995 Addendum 1, 11/97
HVAC Duct Construction Standards - Metal and Flexible (same as UMC 6-2)
Ducts, metal and flexible
506.2,602.1 and 602.5
SMACNA 2003 Fibrous Glass Duct Construction Standard Duct construction, Fiberglass ducts
602.3
*ANSI approved standard
172-16
Item #111
UL 17, 1994 edition 3rd Vent or Chimney Connector Dampers for Oil-Fired Appliances
Vent dampers 1005.4
UL 21, 1995 edition 9th LP-Gas Hose Hose, LPG hose 303.1(4), 303.2(B), 1312.1(5) and 1312.2.
UL 33, 2003 edition 7th Heat Responsive Links for Fire Protection Service Fusible links 606.0
UL 51, 2002 edition 9th Power-Operated Pumps for Anhydrous Ammonia and LP-Gas
Ammonia pumps, LPG pumps, Pumps
516.2.1,1309.5.4.3, 1309.5.9(D), 1313.0
UL 80, 2004 edition 11th Steel Tanks for Oil-Burner Fuel Oil tanks, Tanks 302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 103, 2001 edition 10th Factory-Built Chimneys for Residential Type and Building Heating Appliances
Chimneys, Heating appliance chimneys, Residential chimneys
802.5.1.
UL 125-1997 edition 6th Valves for Anhydrous Ammonia and LP-Gas (Other than Safety Relief)
Ammonia valves, LPG valves, Valves
516.2.1, 1309.5.4.3, 1309.5.9(D),1313.0
UL 127-1996 edition 7thth Factory-Built Fireplaces Fireplaces 802.5.1
UL 132, 1997 edition 6th Safety Relief Valves for Anhydrous Ammonia and LP-Gas
Ammonia relief valves, LPG valves, Relief valves
516.2.1, 1309.5.4.3, 1309.5.9(D), 1313.0
UL 144, 1999 edition 7th LP-Gas Regulators Low pressure boilers, Regulators
1301.0.
UL 174, 2004 edition 11th Household Electric Storage Tank Water Heaters 225.0, 517.1.2, 802.2.2.5, 803.1.8.1, Table 13-1
UL 180-2003 edition 7th Liquid Level Indicating Gauges for Oil Burner Fuels
Gauges, Level gauges 302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 181 2005 Factory-Made Air Ducts and Air Connectors Air connectors, Air ducts
602.5, A.6.501
UL 181A 2005 Closure Systems for Use with Rigid Air Ducts and Air Connectors
Air connectors, Air ducts
602.4
UL 181B 1995 2005 edition 2
Closure Systems for Use with Flexible Air Ducts and Air Connectors
Air Connectors, Air ducts
602.4, A.6.507(A)(4), A.6.508(2) Figures and Chart on page 334, 335, 336, 338
UL 197, 2003 edition 9th Commercial Electric Cooking Appliances [UMC 513.2.2]
Appliances, Commercial cooking, Electric appliances
507.1.5, 513.2.2
UL 207, 2001 edition 7th Non-Electrical Refrigerant-Containing Components and Accessories
Refrigeration components
Ch. 11
*ANSI approved standard
172-17
Item #111
UL 252, 2003 edition 8th Compressed Gas Regulators Regulators
UL 268A, 1998 edition 3rd Smoke Detectors for Duct Application Smoke detectors 609.0
UL 296, 2003 edition 10th Oil Burners Bruners 302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0,1335.2, 1335.3
UL 300 1996 2005 edition 3rd
Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas [UMC 513.2.2]
Certification: Restaurant fire protection
513.2.2
UL 343, 1997 edition 8th Pumps for Oil-Burning Appliances Oil pumps, Pumps 302.3, 1019.0, 1302.0, 1318.0 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 352, 19972006 edition 7 8th
Constant-Level Oil Valves Oil valves, Valves Appendix C “Definition.”
UL 353, 1994 edition 5th Limit Controls Controls 912.2
UL 378, 19932006 edition 3rd 4th
Draft Equipment Draft equipment 1004.15 “Definitions.”
UL 391, 19952006 edition
34th
Solid-Fuel and Combination Fuel Central and Supplementary Furnaces
Furnaces, solid fuel Ch. 9
UL 404, 19972005 edition 7th
Indicating Pressure Gauges for Compressed Gas Service
Gauges, compressed gas
UL 412, 2004 edition 4th Refrigeration Unit Coolers Refrigeration Ch. 11
UL 429, 1999 edition 5th Electrically Operated Valves Valves Ch. 12, 1309.9, Ch.14
UL 441, 1996 edition 9th Gas Vents Vents 802.6
UL 443, 19952006 edition
5 6th
Steel Auxilliary Tanks for Oil Burner Fuel Oil tanks, Tanks 302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 471, 2006 edition 8 9th
Commercial Refrigerators and Freezers Freezers, Refrigerators 923.0, Ch. 11
UL 525, 2004 edition 7th Flame Arresters Flame arrestors Ch. 9
UL 536, 1997 edition 9th Flexible Metallic Hose Hose, Metallic hose Ch. 13
UL 555, 19992006 edition
67th
Fire Dampers Dampers 606.0
UL 555C, 19962006
edition 23rd Ceiling Dampers Dampers 606.0
*ANSI approved standard
172-18
Item #111
UL 555S, 1999 edition 4th Smoke Dampers Dampers 606.0
UL 565, 1998 edition 5th Liquid Level Gauges and Indicators for Anhydrous Ammonia and LP-Gas
Gauges, LP gas 516.2.1, 1309.5.4.3, 1309.5.9(D), 1313.0
UL 569, 1995 edition 7th Pigtails and Flexible Hose Connectors for LP-Gas Connectors, Gas connectors
516.2.2, 1309.5.4.3, 1309.5.9(D), 1313.0
UL 641, 1995 edition 7th Type L Low Temperature Venting Systems Product 302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 710, 1995 edition 5th Exhaust Hoods for Commercial Cooking Equipment
Exhaust hoods, Hoods 508.0, 514.0
UL 723, 2003 edition 9th Test for Surface Burning Characteristics of Building Materials [UMC 508.3, 602.2, 605.0(E), 1201.4.1.3]
Surface burning testing Sections 508.3, 602.2, 605.0(E), 1201.4.1.3
UL 726, 1995 edition 7th Oil-Fired Boiler Assemblies Boiler, oil fired 302.3, Ch. 10, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 727, 19942006 edition 89th
Oil-Fired Central Furnaces Furnaces, central, oil fired
302.3, Ch. 9, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 729, 2003 edition 6th Oil-Fired Floor Furnaces Furnaces, floor, oil-fired furnaces
912.0
UL 730, 2003 edition 5th Oil-Fired Wall Furnaces Furnaces, wall, oil fired 928.0
UL 731, 1995 edition 5th Oil-Fired Heater Units Heaters, oil fired 927.0
UL 732, 1995 edition 5th Oil-Fired Storage Tank Water Heaters Water heaters, oil fired 302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 733, 1993 edition 4th Oil-Fired Water Heaters and Direct-Fired Heaters Water heaters, direct fired, oil fired
302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 737, 1996 edition 8 Fireplace Stoves Fireplace stoves 208.0 “Definitions.”
UL 791, 19932006 edition 4 5th
Residential Incinerators Incinerators Table 8-2.
UL 795, 19992006 edition
56th
Commercial-Industrial Gas Heating Equipment Heating equipment, gas fired
Ch. 10
UL 834, 2004 edition 5th Electric Water Supply Heating and Power Boilers Boilers, Electric ranges Ch. 10
UL 842, 1997 edition 8th Valves for Flammable Fuels Valves 911.8
*ANSI approved standard
172-19
Item #111
UL 858, 19932005 edition 15th
Electric Household Electric Ranges Electric ranges, Ranges 307.2, Ch.9
UL 867, 2000 edition 4th Electrostatic Air Cleaners Filters 516.2.6, Ch. 5, Ch.6
UL 896, 1993 edition 5th Oil-Burning Stoves Stoves, oil fired 302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 900, 2004 edition 7th Air Filter Units Air filters, Filters 312.0
UL 907, 1994 edition 2nd Fireplace Accessories Fireplace accessories Ch. 9
UL 921, 2006 edition 6th Commercial Electric Dishwashers Dishwashers Ch. 5, Part II
UL 959, 2001 edition 8th Medium Heat Appliance Factory-Built Chimneys Chimneys 802.5.1.1
UL 984, 1996 edition 7th Hermetic Refrigerant Motor Compressors Compressors, refrigeration
Ch. 11
UL 1026, 1995 edition 4th Electric Household Cooking and Food Serving Appliances
Cooking appliances, Electric appliances
916.0
UL 1046, 2000 edition 3rd Grease Filters for Exhaust Ducts [UMC 509.1] Filters, grease 509.1
UL 1206, 2003 edition 4th Electric Commercial Clothes-Washing Equipment Clothes Washers, Commercial clothes washers
Ch. 5
UL 1240, 19942005 edition 34th
Electric Commercial Clothes-Drying Equipment Clothes dryers, commercial
905.0
UL 1453, 2004 edition 5th Electric Booster and Commercial Storage Tank Water Heaters
Electric water heaters, Water heaters
302.3, 1019.0, 1302.0, 1318.0, 1332.0(2), 1332.2, 1333.6, 1333.6.1, 1334.0, 1335.2, 1335.3
UL 1482, 1996 edition 5th Solid-Fuel Type Room Heaters Room heaters, Solid fuel heaters
924.0
UL 1738, 1993 edition 2nd Venting Systems for Gas-Burning Appliances, Categories II, III, and IV
Gas vent systems, Vent tystems
802.0
UL 1746, 19932007 edition 23rd
External Corrosion Protection Systems for Steel Underground Storage Tanks
Tanks 204.0
*ANSI approved standard
172-20
Item #111
UL 1777, 2004 edition 3rd Chimney Liners Chimneys, Liners 803.1.6 and 803.2.19.
UL 1812, 1995 edition 2nd Ducted Heat Recovery Ventilators Heat recovery ventilators
Ch. 6
UL 1815, 2001 edition 3rd Nonducted Heat Recovery Ventilators Heat recovey ventilators
Ch. 6
UL 1820, 2004 edition 4th Fire Test of Pneumatic Tubing for Flame and Smoke Characteristics [UMC 602.2(7)]
Surface burning test, pneumatic tubing
602.2(7)
UL 1887, 2004 edition 3rd Fire Test of Plastic Sprinkler Pipe for Visible Flame and Smoke Characteristics [UMC 602.2(6)]
Surface burning test, fire sprinkler pipe
602.2(6)
UL 1963, 19952005 edition 23rd
Refrigerant Recovery/ Recycling Equipment Refrigerant equipment Ch. 11
UL 1978, 20022005 edition 34th
Grease Ducts Ducts, grease 510.4
UL 1995, 19952006 edition
3 4rd
Heating and Cooling Equipment HVAC, electric 307.2, Ch. 6, Ch. 11
UL 2021, 1997 edition 2nd Fixed and Location-Dedicated Electric Room Heaters
Product; Heating, electric
Ch. 9
UL 2043, 1996 edition 2nd Fire Test for Heat and Visible Smoke Release for Discrete Products and Their Accessories Installed in Air Handling Spaces [UMC 602.2(8)]
Surface burning test, discrete products
602.2(8)
UL 2157, 1997 edition 2nd Electric Clothes Washing Machines and Extractors Clothes washers, Extractors
Ch. 5
UL 2158, 1995 edition 2nd Electric Clothes Dryers Clothes dryers,electric 905.0
UL 2221 - 2003 Tests of Fire Resistive Grease Duct Enclosure Assemblies
Duct wrap, grease duct enclosure
507.2.3
*ANSI approved standard
172-21
Item #111