7/28/2019 Refer to the Exhibreferit

1/6

Refer to the exhibit.Branch A has a non-Cisco router that is using IETF encapsulation and Branch B hasa Cisco router. After the commands that are shown are entered, R1 and R2 fail toestablish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfullyestablished at both locations. Why is the PVC failing?

A.The PVC to R1 must be point-to-point.B.LMI types must match on each end of a PVC.C.The frame relay PVCs cannot be established between Cisco and non-Cisco routers.D.The IETF parameter is missing from the frame-relay map ip 10.10.10.1 201 command.Q.2)

7/28/2019 Refer to the Exhibreferit

2/6

Refer to theexhibit. Communication between two peers has failed. Based on the output that isshown, what is the most likely cause?

A.interface reset

B.unplugged cable

C.improper LMI typeD.PPP negotiation failure

Q.3)

A technician is talking to a colleague at a rival company and comparing DSLtransfer rates between the two companies. Both companies are in the same city,use the same service provider, and have the same rate/service plan. What is theexplanation for why company 1 reports higher download speeds than company 2reports?

A.Company 1 only uses microfilters at branch locations.B.Company 1 has a lower volume of POTS traffic than company 2 has.C.Company 2 is located farther from the service provider than company 1 is.D.Company 2 shares the connection to the DSLAM with more clients than company 1 shares with.Q.4)

7/28/2019 Refer to the Exhibreferit

3/6

Refer tothe exhibit. A network administrator is creating a prototype to verify the new WANdesign. However, the communication between the two routers cannot beestablished. Based on the output of the commands, what can be done to solve theproblem?

A.Replace the serial cable .B.Replace the WIC on RA.C.Configure RA with a clock rate command.D.Issue a no shutdown interface command on RB.

Q.5)

Refer tothe exhibit. Router RT is not receiving routing updates from router RTA. What iscausing the problem?

A.The ip rip authentication key-chain command specifies exam rather than test.

7/28/2019 Refer to the Exhibreferit

4/6

B.The name of the keystring is not the name of the neighboring router.C.The key chains are given the same name on both routers.D.The passive-interface command was issued for RTA.Q.6)What are two main components of data confidentiality? (Choose two.)

A.checksumB.digital certificates

C.encapsulationD.encryptionE.hashing

Q.7)Which network component has the primary function of detecting and loggingattacks made against the network?

A.Cisco Security AgentB.antivirus software scannerC.intrusion detection systemD.intrusion prevention system

Q.8)

Refer tothe exhibit. A network technician has been called in to resolve a problem with thisnetwork segment. The symptoms include a loss of connectivity throughout thenetwork segment, high link utilization, and syslog messages that indicate constantMAC address relearning. What is the likely cause of these symptoms?

A.cable faultB.faulty NIC cardC.IP addressing errorD.spanning tree problemE.NAT configuration errorQ.9)Which variable is permitted or denied by a standard access control list?

A.protocol typeB.source IP addressC.source MAC addressD.destination IP addressE.destination MAC addressQ.10)

7/28/2019 Refer to the Exhibreferit

5/6

Referto the exhibit. To reach R2, and for configuring Frame Relay on the point-to-pointinterfaces shown in the graphic, which DLCI should be used in the frame-relay interface-dlci command that is issued on R1?

A.100B.101C.200D.201

Q.11)

A system administrator must provide Internet connectivity for ten hosts in a smallremote office. The ISP has assigned two public IP addresses to this remote office.

How can the system administrator configure the router to provide Internetaccess to all ten users at the same time?

A.Configure DHCP and static NAT.B.Configure dynamic NAT for ten users.C.Configure static NAT for all ten users.D.Configure dynamic NAT with overload.

Q.12)

Refer to theexhibit. Which two actions are described by the output of the debug ip natcommand? (Choose two.)

A.A packet from 192.168.1.2 has been translated using NAT overload.B.The * indicates that the NAT translation was unsuccessful and the packet was dropped.

C.A packet from 192.31.7.2 has been translated by NAT and forwarded to a destination address of198.133.219.2.

7/28/2019 Refer to the Exhibreferit

6/6

D.A packet from 192.31.7.2 has been sent to 198.133.219.2, which was then translated to thedestination 192.168.1.2

E.A packet from 192.168.1.2 has been translated by NAT to a source address of 198.133.219.2 andforwarded to the destination 192.31.7.2.

Q.13)

Refer to theexhibit. Which two actions are described by the output of the debug ip natcommand? (Choose two.)

A.A packet from 192.168.1.2 has been translated using NAT overload.B.The * indicates that the NAT translation was unsuccessful and the packet was dropped.

C.A packet from 192.31.7.2 has been translated by NAT and forwarded to a destination address of

198.133.219.2.D.

A packet from 192.31.7.2 has been sent to 198.133.219.2, which was then translated to thedestination 192.168.1.2

E.A packet from 192.168.1.2 has been translated by NAT to a source address of 198.133.219.2 andforwarded to the destination 192.31.7.2.