renderoc fcxtra submittal

35
Tadmur Trading WLL _____________________________________________________________________ Post Box 37493, Doha Qatar Telephone: Fax: Email: (+974) 44337000 (+974) 44337100 bm.fosroc@tadmur-trading .com Technical Submittal Al Gurg Fosroc LLC P.O. Box 657, Dubai, U.A.E. Tel : +971 4 2039560, Fax : +971 4 2852023 / +971 4 2850406 www.fosroc.com FOSROC RENDEROC FCXTRA Single component polymer modified cementitious pinhole filler, fairing coat and cosmetic mortar

Upload: ajitpushpa

Post on 28-Dec-2015

210 views

Category:

Documents


15 download

DESCRIPTION

Concrete repair material

TRANSCRIPT

Page 1: Renderoc FCXtra Submittal

Tadmur Trading WLL _____________________________________________________________________

Post Box 37493, Doha Qatar Telephone: Fax: Email: (+974) 44337000 (+974) 44337100 bm.fosroc@tadmur-trading .com

Technical Submittal

Al Gurg Fosroc LLC P.O. Box 657, Dubai, U.A.E. Tel : +971 4 2039560, Fax : +971 4 2852023 / +971 4 2850406 www.fosroc.com

FOSROC RENDEROC FCXTRA Single component polymer modified cementitious pinhole filler,

fairing coat and cosmetic mortar

Page 2: Renderoc FCXtra Submittal

CONTENTS

Section 1 Technical Data Sheet

Section 2 Method Statement

Section 3 Material Safety Data Sheet

Section 4 Test Reports

Section 5 Approvals

Page 3: Renderoc FCXtra Submittal

TECHNICAL DATA SHEET

Page 4: Renderoc FCXtra Submittal

Ren

dero

c FC

Xtra

constructive solutionsFosroc Renderoc FCXtra

Single component polymer modified cementitious pinholefiller, fairing coat and cosmetic mortar

Uses

Renderoc FCXtra is designed for application to minorimperfections in concrete and masonry surfaces. It is suitablefor application in the range 0 to 6mm, and can be used in thefollowing situations :

! Filling pinholes prior to overcoating

! General reprofiling over large areas, up to 6mm depth

! To produce a uniform surface over repaired areas

Advantages

! Shrinkage compensated - with no cracking or dusting

! Cost effective - no independent primer necessary

! Time saving - curing not necessary

! High performance - excellent bond to the substrate

! Smooth finish - important for the application of decorativecoatings

Description

Renderoc FCXtra is supplied as a ready to use blend of drypowders which requires only the site addition of clean waterto produce a highly consistent cementitious mortar.

Renderoc FCXtra exhibits excellent thermal compatibility withconcrete, and is fully compatible with other Renderoc*†

mortars and Dekguard*† protective coatings.

Specification

The filler for minor surface imperfections (up to 6 mm depth)shall be Renderoc FCXtra - a single component, polymermodified, cementitious mortar. The material shall be capableof use without the need for an independent primer or curingsystem.

Design criteria

Renderoc FCXtra is designed for vertical and overhead usein filling voids up to a depth of 6 mm. It can also be used torender over large areas, from a feather-edge up to 6 mmthickness.

Properties

The following results were obtained at a liquid:powder ratio of0.3:1 by weight or 1:3 by volume.

Test method Typical result@ 20oC @ 35oC

Working life (Approx.) : 60 mins 30 minsSetting time (BS 5075) : 60 mins 45 minsFresh wet density : 1750 kg/m3

Compressive strength : 20N/mm² - 28days @ 23°C

Note: Working life and setting time will vary dependent onambient and substrate temperatures.

Instructions for use

Preparation

Clean the surface and remove any dust, unsound material,plaster, oil, paint, grease, corrosion deposits or algae. Roughenthe surface to remove any laitence and expose the fineaggregate by light scabbling or grit-blasting.

Oil and grease deposits should be removed by steam cleaning,detergent scrubbing or the use of a proprietary degreaser. Theeffectiveness of decontamination should then be assessedby a pull-off test.

Renderoc repair mortars require no additional preparation priorto the application of Renderoc FCXtra.

The cleaned areas should be blown clean with oil-freecompressed air before continuing. All prepared areas shouldbe thoroughly soaked with clean water immediately prior tothe application of Renderoc FCXtra. Any residual surface watershould be removed prior to commencement.

Mixing - small quantities

Care should be taken to ensure that Renderoc FCXtra isthoroughly mixed. Small quantities (up to 5 kg) can be mixedusing a suitable mixing drum or bucket. Greater quantitiesshould be mixed using a forced-action mixer. Mixing in a suitablysized drum using an approved spiral paddle attached to anapproved slow speed (400/500 rpm) heavy-duty drill is anacceptable alternative.

If mixing small quantities by hand, Renderoc FCXtra shouldbe volume-batched. Add 3 volumes of the Renderoc FCXtrapowder (loose-filled to excess and struck off level with the topof the measuring container) to one volume of potable water.This should be mixed vigorously until fully homogeneous.

Page 5: Renderoc FCXtra Submittal

Renderoc FCXtra - Page 2 of 4

Fosroc Renderoc FCXtra

Mixing - large volumes

For larger volumes, place 6.5-7.5 litres of cool, potable waterinto the mixer and, with the machine in operation, add onefull 25 kg bag of Renderoc FCXtra and mix continuously for 3to 5 minutes until fully homogeneous.

Water addition may vary slightly according to both the ambienttemperature and the desired consistency of the mix, but itshould not exceed 7.5 litres

For enhanced performance properties, add upto 1litre ofNitobond SBR to the gauging water until the desiredconsistency is achieved.

Note : In all cases Renderoc FCXtra powder must beadded to the water.

Application

Apply the mixed Renderoc FCXtra to the prepared substrate,up to 6 mm thickness, by steel trowel. It should be appliedwith the minimum of working and be allowed to partly setbefore finally trowelling to a smooth finish.

If a very smooth finish is required, a small amount of watermay be flicked on to the surface of the Renderoc FCXtra with apaint brush prior to final trowelling.

Do not proceed with the application when rainfall is imminentunless in a sheltered or protected situation.

Finishing

Renderoc FCXtra is finished by striking off with a straight edgeand closing with a steel or plastic float. Note that water can bedrawn to the surface if ‘overworking’ with the float occurs, andan unsightly finish may result.

Damp sponges or plastic floats may be used to achieve adesired surface texture, but care should again be taken not tooverwork the surface.

Curing

Curing is not generally required. However, under extremeconditions - high temperatures and drying winds - it may beprudent to use Nitobond AR*† or Nitocote PE135 as a curingagent.

Nitobond AR does not require mechanical removal prior toovercoating with the Dekguard Range. Nitocote PE135 shouldbe used, when overcoated with epoxy and polyurethanecoatings.

Cleaning

Renderoc FCXtra should be removed from tools, equipmentand mixers with clean water immediately after use. Curedmaterial can only be removed by mechanical means.

Overcoating with protective/decorative finishes

Renderoc FCXtra may be overcoated with a protective /decorativecoating after about 48 hours, dependent on ambient conditions.Fosroc recommend the use of the Dekguard range of protective,anti-carbonation coatings. These products provide a decorativeand uniform appearance as well as protecting parts of thestructure which have not been repaired and might otherwisebe at risk from the environment.

Limitations

! Renderoc FCXtra should not be used when the temperatureis below 5°C and falling.

! Do not proceed with the application when rainfall is imminentunless in a sheltered or protected situation.

! The product should not be exposed to moving water duringapplication or prior to initial set.

! If any doubts arise concerning temperature or substrateconditions, consult the local Fosroc office.

High temperature working

It is suggested that, for temperatures above 350C, the followingguidelines are adopted as good working practice:

(i) Store unmixed materials in a cool (preferably temperaturecontrolled) environment, avoiding exposure to direct sunlight.

(ii) Keep equipment cool, arranging shade protection ifnecessary. It is especially important to keep cool thosesurfaces of the equipment which will come into direct contactwith the material itself.

(iii) Try to avoid application during the hottest times of the day,and in direct sunlight.

(iv) Make sufficient material, plant and labour available to ensurethat application is a continuous process.

Technical support

Fosroc offers a comprehensive technical support service tospecifiers, end users and contractors. It is also able to offer on-site technical assistance, an AutoCAD facility and dedicatedspecification assistance in locations all over the world.

Page 6: Renderoc FCXtra Submittal

Renderoc FCXtra - Page 3 of 4

Fosroc Renderoc FCXtra

Estimating

SupplyRenderoc FCXtra : 25 kg bagsNitobond SBR : 25 and 200 litre drumsNitobond AR : 1 and 5 litre packs

Coverage and yieldRenderoc FCXtra : 16.2 litres per 25kg bagNitobond AR : 6 to 8 m2 per litre

Note : Actual coverage of Renderoc FCXtra will be whollydependent upon the general substrate condition. It isrecommended, therefore, that site trials over a typicalarea are carried out to determine actual usage.

Storage

Shelf life

All products have a shelf life of 12 months if kept in a dry storein the original, unopened bags or packs @ 25oC.

Storage conditions

Store in dry conditions in the original, unopened bags or packs.If stored at high temperatures and/or high humidity conditionsthe shelf life may be considerably reduced to 4 to 6 months.

Precautions

Health and safety

Renderoc FCXtra contains cement powders which, whenmixed or become damp, release alkalis which can be harmfulto the skin. Nitobond AR and Nitobond SBR are slightlyalkaline.

During use, avoid inhalation of dust and contact with skin andeyes. Wear suitable protective clothing, gloves, eye protectionand respiratory protective equipment.

The use of barrier creams can provide additional skinprotection. In case of contact with skin, rinse with plenty ofclean water, then cleanse with soap and water. In case ofcontact with eyes, rinse immediately with plenty of clean waterand seek medical advice. If swallowed, seek medical attentionimmediately - do not induce vomiting.

For further information, refer to the appropriate Product MaterialSafety Data Sheet.

Fire

Renderoc FCXtra, Nitobond AR and Nitobond SBR are allnon-flammable products.

Page 7: Renderoc FCXtra Submittal

UAE/0535/06/B

Fosroc Renderoc FCXtra

Al Gurg Fosroc LLCPost Box 657, DubaiUnited Arab Emirates

www.fosroc.com

Important noteFosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions forthe Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility toobtain the latest version.

Head Officetelephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]

Regional officesAbu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected], YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected], Boodai telephone: 4817618 fax: 4832124 email: [email protected], Al Amana telephone: 24815080 fax: 24817554 email: [email protected], Tadmur telephone: 4432365 fax: 4419517 email: [email protected]

* Denotes the trademark of Fosroc International Limited

† See separate data sheet

Additional Information

Fosroc manufactures a wide range of complementaryproducts which include :

! waterproofing membranes & waterstops

! joint sealants & filler boards

! cementitious & epoxy grouts

! specialised flooring materials

Fosroc additionally offers a comprehensive package ofproducts specifically designed for the repair andrefurbishment of damaged concrete. Fosroc’s ‘SystematicApproach’ to concrete repair features the following :

! hand-placed repair mortars

! spray grade repair mortars

! fluid micro-concretes

! chemically resistant epoxy mortars

! anti-carbonation/anti-chloride protective coatings

! chemical and abrasion resistant coatings

For further information on any of the above, please consultyour local Fosroc office - as below.

Page 8: Renderoc FCXtra Submittal

METHOD STATEMENT

Page 9: Renderoc FCXtra Submittal

telephone: fax: email: (+9714) 2039699 (+9714) 2859649 [email protected] Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai

Al Gurg Fosroc LLC Post Box 657, Dubai United Arab Emirates www.fosroc.com

constructive solutions method statement

Renderoc FCXtra Section A : General Comments High temperature working It is suggested that, for temperatures above 35°C, the following guidelines are adopted as good

working practice: (i) Store unmixed materials in a cool (preferably temperature controlled) environment, avoiding

exposure to direct sunlight.

(ii) Keep equipment cool, arranging shade protection if necessary. It is especially important to keep cool those surfaces of the equipment which will come into direct contact with the material itself.

(iii) Try to avoid application during the hottest times of the day, arrange temporary shading as necessary.

(iv) Make sufficient material, plant and labour available to ensure that application is a continuous process.

(v) Where mixing water is required in the application of a product, it is advised to maintain such water at a maximum of 200C

Equipment It is suggested that the following list of equipment is adopted as a minimum requirement Protective clothing : Protective overalls : Good quality gloves, goggles and face mask Preparation equipment : Wire brush : Proprietary blasting equipment Mixing equipment : Measuring jug : 1 KW slow speed drill, 400 or 500 rpm + Fosroc MR4 mortar mixing paddle + suitably sized mixing vessel, for single bag

mixing, or : Proprietary forced-action mixer for multiple bag

mixing Application equipment : Hand application trowel : Wooden float : Steel or plastic finishing float : Finishing sponge

Application - points of note

Fosroc operates a policy to encourage the use, where possible, of registered applicators, since the long term performance of the materials is dependent upon proper application. For contractors who wish to apply the materials themselves Fosroc is also able to offer technical assistance and training, either on-site or at its Training Centre in Dubai.

Page 10: Renderoc FCXtra Submittal

constructive solutions

Section B : Application Method

1.0 Surface preparation

Attention to full and proper preparation of the substrate is essential for complete repair adhesion.

1.1 The surface of the substrate should be thoroughly cleaned to remove all traces of dust, oil, paint, curing compounds, grease, corrosion deposits, algae or any unsound material which might affect subsequent bond between Renderoc FCXtra and the substrate.

1.2 Oil and grease deposits are best removed by steam cleaning, detergent scrubbing or the use of a proprietary degreaser. The effectiveness of decontamination should be assessed by a pull-off test.

1.3 The substrate should further be ‘roughened’ to remove excess laitence, to expose pinholes & blowholes and to provide a mechanical key for subsequent application of Renderoc FCXtra. This is most effectively achieved by the use of proprietary blast media, such that the fine aggregate is exposed but not polished.

1.4 Where preparation techniques result in voids of greater than 3 mm depth, it will be necessary to use other Renderoc products to make local repairs before overcoating with Renderoc FCXtra. Such areas, once repaired, will not require additional preparation prior to the application of Renderoc FCXtra.

1.5 Immediately prior to application of Renderoc FCXtra, the prepared substrate should be blown clean with oil-free compressed air.

2.0 Substrate priming

2.1 All prepared areas should be thoroughly soaked with clean, potable water immediately prior to the application of Renderoc FCXtra, such that the substrate is “saturated surface dry”.

2.2 Since Renderoc FCXtra is only a surface skim coat, reinforcing steel should not be exposed and will not therefore need priming.

3.0 Mixing

Care should be taken to ensure that Renderoc FCXtra is thoroughly mixed. In all cases the powder should be added to the water and mixed strictly in accordance with appropriate procedure.

3.1 Mixing - small quantities

a) Small quantities - up to 5 kg - may be mixed manually.

b) The mixing ratio, by volume, should be 3 parts Renderoc FCXtra to 1 part water.

c) For the single volume water component select a conveniently sized measuring container and fill to the top. Add the measured volume of potable water to the mixing vessel.

Page 2 of 4

Page 11: Renderoc FCXtra Submittal

constructive solutions

d) For each of 3 volumes of Renderoc FCXtra, loose-fill the measuring container to excess with Renderoc FCXtra, then strike off level with the top of the measuring container.

e) Add the 3 volumes of powder to the water and mix vigorously for at least 3 minutes, until homogenous.

3.2 Mixing - large volumes

a) For larger volumes of material it will be necessary to mix using

- a proprietary forced action mixer, or

- slow speed drill (400/500 rpm) + Fosroc MR4 mortar paddle attachment.

b) For each bag of Renderoc FCXtra to be mixed, measure out and place 5 to 6 litres of cool, potable water into the mixer (water quantity may vary slightly according to ambient temperature and desired consistency of mix).

c) Always add the powder to the water. With the mixer in operation add one full bag of Renderoc FCXtra, or multiples thereof, and mix continuously for 5 minutes until fully homogenous.

d) Enhanced performance properties can be gained by adding up to 1 litre of Nitobond SBR (per full bag of Renderoc FCXtra) in addition to the normal gauging water, until the desired consistency is achieved.

4.0 Application

Do not proceed with the application when rainfall is imminent, unless in a sheltered or protected position.

4.1 Apply the fully mixed Renderoc FCXtra to the prepared substrate, up to 6 mm thickness, by steel trowel. It should be applied with the minimum of working, and be allowed to partly set before finally trowelling to a smooth finish.

4.2 Thickness of application should be in accordance with that laid down in the ‘Application criteria’ section of the current product data sheet.

4.3 If a very smooth finish is required, a small amount of water may be flicked onto the surface of the Renderoc FCXtra, with a paint brush, prior to final trowelling.

5.0 Finishing

5.1 Renderoc FCXtra is finished by striking off with a straight edge and closing with a steel or plastic float. Note that water can be drawn to the surface if ‘overworking with the float occurs, and an unsightly finish may result.

5.2 Damp sponges or plastic floats may be used to achieve a desired surface texture, but care should again be taken not to overwork the surface.

6.0 Curing

6.1 Curing of Renderoc FCXtra is not generally required. However, under extreme drying conditions - high temperatures, drying winds, use Nitobond AR or Nitocote PE135.

Page 3 of 4

Page 12: Renderoc FCXtra Submittal

Page 4 of 4

constructive solutions

7.0 Cleaning

7.1 All equipment should be washed with clean water immediately after use. Cured material can only be removed by mechanical means.

Section C : Approval and variations

This method statement is offered by Fosroc as a ‘standard proposal’ for the application of Renderoc FCXtra. It remains the responsibility of the Customer to determine the correct method for any given application. Where alternative methods are to be used, these must be submitted to Fosroc for comment, in writing, prior to the commencement of any work.

Page 13: Renderoc FCXtra Submittal

Page 4 of 4

constructive solutions

7.0 Cleaning

7.1 All equipment should be washed with clean water immediately after use. Cured material can only be removed by mechanical means.

Section C : Approval and variations

This method statement is offered by Fosroc as a ‘standard proposal’ for the application of Renderoc FCXtra. It remains the responsibility of the Customer to determine the correct method for any given application. Where alternative methods are to be used, these must be submitted to Fosroc for comment, in writing, prior to the commencement of any work.

Page 14: Renderoc FCXtra Submittal

MATERIAL SAFETY DATASHEET

Page 15: Renderoc FCXtra Submittal

REVISION DATE 15/02/2011 REV. NO./REPL. SDS GENERATED 2

SAFETY DATA SHEET

RENDEROC FC XTRA

1 IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING

PRODUCT NAME RENDEROC FC XTRA

PRODUCT NO. 2189040AEDXB1

AL GURG FOSROC LLCSUPPLIER

PO BOX 657

Al Hamer Road

Al Ramool Industrial Estate

Dubai

UAE

+97142858606

EMERGENCY TELEPHONE +97142039699 (08:00 to 16:30) // +971506258232 (16:30 to 08:00)GMT+4

MANUFACTURER Al Gurg Fosroc LLC, Al Ramool Industrial Estate, Dubai , UAE.

2 HAZARDS IDENTIFICATION

Irritating to eyes, respiratory system and skin.

CLASSIFICATION (1999/45) Xi;R36/37/38.

ENVIRONMENT

In the presence of water the product hardens to a solid mass which is not biodegradable.

HUMAN HEALTH

Dust or splashes from the mixture may cause permanent eye damage. Dust may irritate throat and respiratory system and cause

coughing. Dust has an irritating effect on moist skin. Prolonged contact with wet cement/mixture may cause burns. Frequent inhalation of

dust over a long period of time increases the risk of developing lung diseases.

3 COMPOSITION/INFORMATION ON INGREDIENTS

EC No.Name Classification (67/548)CAS-No. Content %

SILICA SAND Xi;R36/37.14808-60-7 30-60%

CEMENT -65997-15-1 30-60%

207-439-9CALCIUM CARBONATE -471-34-1 10-30%

The Full Text for all R-Phrases are Displayed in Section 16

4 FIRST-AID MEASURES

INHALATION

Move injured person into fresh air and keep person calm under observation. If uncomfortable: Seek hospital and bring these instructions.

INGESTION

Immediately rinse mouth and drink plenty of water or milk. Keep person under observation. Do not induce vomiting. If vomiting occurs, keep

head low. Transport immediately to hospital and bring along these instructions.

SKIN CONTACT

Remove contaminated clothing immediately and wash skin with soap and water. Get medical attention if irritation persists after washing.

EYE CONTACT

Do not rub eye. Immediately flush with plenty of water for up to 15 minutes. Remove any contact lenses and open eyelids widely. If irritation

persists: Continue flushing during transport to hospital. Bring these instructions.

51 /

Page 16: Renderoc FCXtra Submittal

REVISION DATE 15/02/2011 REV. NO./REPL. SDS GENERATED 2

RENDEROC FC XTRA

5 FIRE-FIGHTING MEASURES

EXTINGUISHING MEDIA

Use fire-extinguishing media appropriate for surrounding materials.

SPECIFIC HAZARDS

Water used for fire extinguishing, which has been in contact with the product, may be corrosive.

PROTECTIVE MEASURES IN FIRE

Selection of respiratory protection for fire fighting: follow the general fire precautions indicated in the workplace.

6 ACCIDENTAL RELEASE MEASURES

PERSONAL PRECAUTIONS

Avoid inhalation of dust. Use work methods which minimize dust production. Avoid contact with eyes and prolonged skin contact. For

personal protection, see section 8.

ENVIRONMENTAL PRECAUTIONS

The product should not be dumped in nature but collected and delivered according to agreement with the local authorities. Do not discharge

into drains, water courses or onto the ground.

SPILL CLEAN UP METHODS

For waste disposal, see section 13. Collect powder using special dust vacuum cleaner with particle filter or carefully sweep into closed

container.

7 HANDLING AND STORAGE

USAGE PRECAUTIONS

Observe good chemical hygiene practices. Avoid spread of dust. Avoid inhalation of dust. Avoid contact with eyes and prolonged skin

contact. Mechanical ventilation may be required. Change contaminated clothing.

STORAGE PRECAUTIONS

To be stored out of reach of children in its original packaging in a dry place. The product contains less than 2 mg chromate/kg dry cement,

and this limit will not be exceeded for 12 months from the packing date stated on the packaging. Seal opened containers and use up as soon

as possible

8 EXPOSURE CONTROLS/PERSONAL PROTECTION

STD STEL - 15 MinTWA - 8 HrsName Notes

15 mg/m3

total dust

PELCALCIUM CARBONATE

4 mg/m3WELCEMENT

0,1 mg/m3WELSILICA SAND

PEL = Přípustné expoziční limity.

WEL = Workplace Exposure Limit.

INGREDIENT COMMENTS

WEL = Workplace Exposure Limits

PROTECTIVE EQUIPMENT

52 /

Page 17: Renderoc FCXtra Submittal

REVISION DATE 15/02/2011 REV. NO./REPL. SDS GENERATED 2

RENDEROC FC XTRA

PROCESS CONDITIONS

This product contains silica sands.

The grain size distribution of silica sand present means that it is not classified as hazardous.

However, any respirable crystalline dust generated by secondary processing may may cause health effects.

Prolonged and /or massive inhalation of respirable crystalline silica dust may cause lung fibrosis, commonly referred to as silicosis. Principal

symptoms of silicosis are cough and breathlessness.

Occupational exposure to respirable crystalline silica dust should be monitored and controlled

ENGINEERING MEASURES

Provide adequate ventilation. Observe occupational exposure limits and minimize the risk of inhalation of dust.

RESPIRATORY EQUIPMENT

Use respiratory equipment with particle filter, type P2.

Dust mask/respirator.

(EN 149)

HAND PROTECTION

Wear protective gloves. PVC or rubber gloves are recommended. The most suitable glove must be chosen in consultation with the gloves

supplier, who can inform about the breakthrough time of the glove material. If signs of wear and tear are noticed then the gloves should be

replaced.

EYE PROTECTION

(conform EN 166) Wear goggles/face shield.

OTHER PROTECTION

Wear appropriate clothing to prevent any possibility of skin contact.

HYGIENE MEASURES

Change contaminated clothing. When using do not eat, drink or smoke.

PERSONAL PROTECTION

Personal protection equipment should be chosen according to the CEN standards and in discussion with the supplier of the personal

protective equipment. This product may present a chromate (VI) allergy risk. It contains a chromate reducing agent, but users should wear

appropriate personal protective equipment.

ENVIRONMENTAL EXPOSURE CONTROLS

Not available

9 PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE Powder, dust

COLOUR Grey

ODOUR Odourless

SOLUBILITY Insoluble in water

RELATIVE DENSITY 1.2 @ 20 deg C

10 STABILITY AND REACTIVITY

STABILITY

Stable under normal temperature conditions. When stored under humid conditions, the chromate neutralization will decrease. This product

contains a chromate reducing agent to reduce the risk of allergic dermatitis causes by chromium (VI). This product has a shelf life. If not

stored in accordance with packaging instructions (sealed and dry), there is an increased risk of the presence of hexavalent chromate

leading to an increased risk of an allergic reaction. The product will harden into a hard mass in contact with water and moisture.

CONDITIONS TO AVOID

Water, moisture.

MATERIALS TO AVOID

Strong acids.

HAZARDOUS DECOMPOSITION PRODUCTS

Fire creates: Carbon monoxide (CO). Carbon dioxide (CO2).

11 TOXICOLOGICAL INFORMATION

53 /

Page 18: Renderoc FCXtra Submittal

REVISION DATE 15/02/2011 REV. NO./REPL. SDS GENERATED 2

RENDEROC FC XTRA

INHALATION

Dust may irritate throat and respiratory system and cause coughing.

INGESTION

Not likely, due to the form of the product. Ingestion may cause severe irritation of the mouth, the oesophagus and the gastrointestinal

tract.

SKIN CONTACT

Dust has an irritating effect on moist skin. Prolonged contact with wet cement/mixture may cause burns.

EYE CONTACT

Dust or splashes from the mixture may cause permanent eye damage. Immediate first aid is necessary.

SPECIFIC EFFECTS

Frequent inhalation of dust over a long period of time increases the risk of developing lung diseases.

12 ECOLOGICAL INFORMATION

ECOTOXICITY

The product is not expected to be hazardous to the environment.

MOBILITY

The product is not volatile but may be spread by dust-raising handling.

DEGRADABILITY

The product is not biodegradable.

13 DISPOSAL CONSIDERATIONS

DISPOSAL METHODS

Dispose of waste and residues in accordance with local authority requirements. Note that fully cured material is not considered as

hazardous waste.

WASTE CLASS

Waste from residues: 17-09-03

14 TRANSPORT INFORMATION

GENERAL The product is not covered by international regulation on the transport of dangerous goods (IMDG, IATA,

ADR/RID).

No transport warning sign required.

ROAD TRANSPORT NOTES Not Classified

RAIL TRANSPORT NOTES Not classified.

SEA TRANSPORT NOTES Not classified.

AIR TRANSPORT NOTES Not classified.

No.ENVIRONMENTALLY

HAZARDOUS

SUBSTANCE/MARINE

POLLUTANT

15 REGULATORY INFORMATION

LABELLING

Irritant

RISK PHRASES

R36/37/38 Irritating to eyes, respiratory system and skin.

54 /

Page 19: Renderoc FCXtra Submittal

REVISION DATE 15/02/2011 REV. NO./REPL. SDS GENERATED 2

RENDEROC FC XTRA

SAFETY PHRASES

S24/25 Avoid contact with skin and eyes.

S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical

advice.

S37 Wear suitable gloves.

S51 Use only in well-ventilated areas.

S60 This material and its container must be disposed of as hazardous waste.

STATUTORY INSTRUMENTS

The Chemicals (Hazard Information and Packaging for Supply) Regulations 2009 (S.I 2009 No. 716).

APPROVED CODE OF PRACTICE

Classification and Labelling of Substances and Preparations Dangerous for Supply.

Safety Data Sheets for Substances and Preparations.

GUIDANCE NOTES

Workplace Exposure Limits EH40.

CHIP for everyone HSG(108).

NATIONAL REGULATIONS

Regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration,

Evaluation, Authorisation and Restriction of Chemicals (REACH), establishing a European Chemicals Agency, amending Directive

1999/45/EC and repealing Council Regulation (EEC) No 793/93 and Commission Regulation (EC) No 1488/94 as well as Council Directive

76/769/EEC and Commission Directives 91/155/EEC, 93/67/EEC, 93/105/EC and 2000/21/EC, including amendments.

16 OTHER INFORMATION

GENERAL INFORMATION

The user must be instructed in the proper work procedure and be familiar with the contents of these instructions.

REVISION DATE 15/02/2011

REV. NO./REPL. SDS GENERATED 2

RISK PHRASES IN FULL

Irritating to eyes and respiratory system.R36/37

Irritating to eyes, respiratory system and skin.R36/37/38

DISCLAIMER

The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in

accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using

the product in combination with any other product or any other process is the responsibility of the user.

55 /

Page 20: Renderoc FCXtra Submittal

TEST REPORTS

Page 21: Renderoc FCXtra Submittal
Page 22: Renderoc FCXtra Submittal
Page 23: Renderoc FCXtra Submittal
Page 24: Renderoc FCXtra Submittal
Page 25: Renderoc FCXtra Submittal
Page 26: Renderoc FCXtra Submittal
Page 27: Renderoc FCXtra Submittal

APPROVALS

Page 28: Renderoc FCXtra Submittal
Page 29: Renderoc FCXtra Submittal
Page 30: Renderoc FCXtra Submittal
Page 31: Renderoc FCXtra Submittal
Page 32: Renderoc FCXtra Submittal
Page 33: Renderoc FCXtra Submittal
Page 34: Renderoc FCXtra Submittal
Page 35: Renderoc FCXtra Submittal