request for quotations no. 19ja80-18-q-0045 · window film ultra 600 from 3m. ... 3.12. commode:...
TRANSCRIPT
Request for Quotations No. 19JA80-18-Q-0045 Amendment 0001
Page 1 of 1
Section B: Scope of Work
The character and scope of the work are set forth in the purchase order of the Statement of Work as Attachment I-1 – Rev. January 9, 2018, Master Bathroom Layout as Attachment I-2 _ Rev. January 9, 2018, Specification as Attachment I–3_Rev. January 9, 2018 and the RSO Tokyo Security as Attachment I-4 in Section I. The Contractor shall furnish and install all materials required by this purchase order.
In case of differences between small and large-scale drawings, the latter will govern. Where a portion of the work is drawn in detail and the remainder of the work is indicated in outline, the parts drawn in detail shall apply also to all other portions of the work.
Request for Quotations No. 19JA80-18-Q-0045 Amendment 0001
Page 1 of 4
1
Scope of Work
Repair Work in DCMR Master Bathroom
Specifications/Statement of Work
1. Scope of Work
Repair bathrooms in 2nd
floor Master bathroom in DCMR.
2. GENERAL
2.1. All work required under this contract shall be accomplished in accordance with Japan
Architectural Specification Standard (JASS). All work required under this contract shall be
performed in a professional manner of the respective trade. The Contracting Officer’s
Representative (COR) and/or COR’s designee shall perform QA/QC inspection on contracted
work at-any-time basis. Any found deficiencies and/or discrepancies against contract work
requirement and specifications shall be corrected accordingly by the Contractor at no additional
cost to the government.
2.2. All materials and labor shall be furnished by the Contractor unless otherwise stipulated
herein. Quality of all materials to be used for all required work shall meet or exceed Japan
Industrial Standard (JIS).
2.3. The Contractor shall be responsible for keeping the work areas clean and neat. After
completion of work, the Contractor shall clean the work areas and leave it in a vacuum-clean
condition. The Contractor shall dispose of all debris left over from the contracted work outside
the DCM Residence in accordance with applicable local codes for industrial waste disposal,
unless otherwise stipulated herein.
2.4. Prior to work commencement on the job site, the Contractor shall submit to the COR for
approval material samples, shop drawings, color samples, and a work schedule as requested.
2.5. The Contractor shall guarantee all the work completed and any materials supplied by the
Contractor under this contract one (1) year from the date of acceptance against any defects.
2.6. It is the Contractor’s responsibility to verify all dimensions and any site conditions. The
Contractor shall notify the COR of any discrepancies or inconsistencies between the plans and
the site conditions before work occurs and alters the existing conditions.
2.7. It is the Contractor’s responsibility to notify the COR of any discrepancies between the
plans and the specifications or any requirements identified in the contract prior to the
commencement of work. If any such discrepancies are identified after the commencement of
work, the COR will decide which detail or statement is most beneficial to the USG and that
detail or statement will be implemented by the Contractor at the Contractor’s expense.
Request for Quotations No. 19JA80-18-Q-0045 Amendment 0001
Page 2 of 4
2
3.0. Master bathroom repair work: Products are listed hereafter or all those of equals
3.1. Removal work: Remove and dispose of existing floor tiles, built in cabinet, basin,
commode, bathtub, shower head and mixing valve, mirror and lighting fixtures. Remove the
wood door to hallway and to bedroom. Make barriers with temporary studs and plastic sheets for
dust control.
3.2 Base Cabinet:
Contractor shall fabricate 2 sets of sink cabinet, 1 set of W450mm drawer cabinet, 1 sets of W1000mm
drawer cabinet using door panels and aprons equivalent finish to Wood Grain Gloss WG-1712GN from
3M DI-NOC Film. Door panel edge must be round finished. Height of base cabinet is 800mm from the
floor. Inside cabinet shall be finished with white polyester film finish.
Furnish and install silver flush type door pull.
3.3 Countertop:
New W1500 X D600mm counter surface material shall be acrylic marble Dupon CORIAN/Sierra White
Stone or its equivalent. 12.3mm thickness of acrylic marble top surface plus 12mm of plywood plus 3mm
acrylic marble back surface. 5mm Tapered edge finish is required.
80mm high backsplash shall be neatly sealed along the edge.
Furnish and install 2 sets of under mount type basin L620 from TOTO.
Furnish and install two sets of Lavatory faucet TLCF31E from TOTO.
3.4. Mirror: Furnish two sets of mirrors W2235XH1200mm and W1735XH1200mm
covering from top of the splash guard.
3.5. Floor: Contractor shall furnish new 300X300mm ceramic floor tiles THERMO TILE
SOFULIMEII IFT-300 for Lavatory, Bath and Toilet space. Use the same tile for apron and
edges for bathtub. Color will be selected DCM before ordering the product.
3.6. Wall:
3.6.1 Ceramic tiles: Furnish RTM-200/1B and MSJ/KS-11K and install as making checkered
pattern.
3.6.2 Wood texture panel finish: Furnish wall panels with wood texture film equivalent to the
finish of WG-2860 Walnut from 3M DI-NOC.
3.6.3 Confirm the type of wall finish in elevations.
3.7. Door
3.7.1 Wood door: Remove 2 sets of entry door and associated doorjamb/header. Close one
of the openings facing to the hallway with studs and drywall. Replace with solid core door
matched in existing design for the door facing to the bedroom. Furnish new hardware and install
on new doors matched with existing. Paint the door and door frame with oil base paint to be
Request for Quotations No. 19JA80-18-Q-0045 Amendment 0001
Page 3 of 4
3
matched with existing color. Furnish one set of coat hook LIXIL INAX Double Hook KF-28
and install on the inside door surface at 1700mm height.
3.7.2 Glass door:
Remove old door and door jamb/header into the bathtub space and toilet. Furnish new stainless
steel doorjamb/header. Furnish frameless glass door W10mm tempered glass with SRWF
window film ULTRA 600 from 3M. Frosty finish is required from H200mm to H1800mm on
glasses. Use stainless steel hinges. Furnish stainless steel door handle/towel bar matched with
the catalogue design.
3.8. Ceiling: Remove old ceiling board and install new waterproof drywall (aqua board) for
ceiling. Putty the joints and create a smooth surface for receiving paint. Install one set of 500X
500mm access hatch in the bath space and Lavatory space.
3.9. Lighting: Furnish 1 sets of LED down light fixture LGW51700 from Panasonic installed
in the center room of Basin/Changing room. Furnish two sets of wall mount tube LED lighting
LGB85000 and install over the mirror. Furnish a total of 4 sets of LED down light fixture
LGW71730 and install 2 sets in front of medicine cabinet, 1 set over counter top and one set over
toilet. Furnish two sets of wall mount LED light fixture LGW51700 from Panasonic installed in
Bath space. Furnish a motion sensor switch for LGW51700.
3.10. Bathtub space:
Remove existing tiles and mortar until waterproof membrane is exposed in body wash area
outside bathtub. Clean the surface and apply new asphalt waterproof membrane. Install new
drain and create a minimum slope on floor with cement mortar prior to installing new tiles.
The Contractor shall furnish new bathtub TBND-1600HP from INAX. Construct the bathtub
apron and tub edges with concrete blocks. Apply waterproof membrane on concrete block and
install ceramic tile THERMO TILE SOFULIME II, IFT-300 from INAX.
Plumbing shall be replaced including the trap in the ceiling space of 1st floor in the Formal
Dining room.
Furnish bathtub faucet KAKUDAI-154-000K from KAKUDAI.
Furnish shower faucet/shower head with mixing valve heads KAKUDAI-173-235K from
KAKUDAI. Furnish and install height adjustable shower head hook with stainless steel bar for
the particular head model.
Furnish bathroom mirror KF-4510A from INAX.
Furnish D200mm acrylic marble counter with H200mm apron to be installed at the same height
as bathtub edge. Install the shower faucet on the apron.
3.11. Power outlets: Remain existing power outlet at the same locations. Install one GFCI
100V outlet behind toilet for warm shower seat.
3.12. Commode: Furnish the remodel series of no water tank commode NEOREST AH white
color with stick remote control unit.
3.13. Medicine cabinet:
Request for Quotations No. 19JA80-18-Q-0045 Amendment 0001
Page 4 of 4
4
Contractor shall remove existing built in cabinet and associated door panels. Fabricate new
H1000mm cabinets with 200mm depth with height adjustable glass shelves. Provide wood
texture film finish equivalent to WG-2860 Walnut from 3M DI-NOC film for door panel. White
melamine shall be installed for inside cabinet.
3.14. New space heater:
Contractor shall remove old space heaters in basin space and in toilet space. Furnish one set of
new radiant heater in toilet and one set under Medicine cabinet. Connect necessary plumbing.
Accessories:
3.16. Furnish one set of toilet paper holder AUS835M from UNION, two sets of towel-ring
AUS825M from UNION installed on basin aprons, one set of towel bar AUS815M from
UNION, two sets of soap dishes S6N from TOTO, one set of I-shape grab bar in the bathtub
TS134GKY8S from TOTO (white), and one set of L-shape grab bar in the bathtub
TS134GLCY8S from TOTO (white). Furnish and install one set of bathrobe hook AUS845
from UNION on entry door.
3.17. Furnish one set of Sanitary box ST-M3, DP-28L-SA from Yamazaki Sangyo
(CONDOR).
3.18. Soap dispenser: Furnish 2 sets of portable auto flow soap dispenser “EVASOLO
Automatic soap dispenser 200ml (Silver) imported by Smart Kitchen.
3.19. Furnish 1 set of exhaust fan VD-20ZC10 from Mitsubishi installed in Toilet ceiling and 1
set of exhaust / heater fan WD-220BZR from Mitsubishi installed in Bathtub space ceiling.
Request for Quotations No. 19JA80-18-Q-0045 Amendment 0001
Page 2 of 4
/Equal Unit Under-Counter Type Sink
Counter Top Line
ScaleDate
XXXXXX
Request for Quotations No. 19JA80-18-Q-0045 Amendment 0001
Page 3 of 4
Accessory List
①Bar Handle
②Tube Gasket
③Gasket(Large)
④Gasket(Sm
all)⑤
Washer(s)
⑥Caps
⑦Screw
⑧Taper Parts
⑨Set Screw
⑩Hex W
rench
*Com
es with Bar H
andle Unit