revised 09-17-01 part no. 4904wp part's manual · to the owner/operator/dealer all implements...

© 2004 Alamo Group Inc.

PART'S MANUALAn Operator's Manual was shipped with the equipment in theManual Canister. This Operator's Manual is an integral part ofthe safe operation of this machine and must be maintainedwith the unit at all times. READ, UNDERSTAND, and FOLLOWthe Safety and Operation Instructions contained in this manualbefore operating the equipment. If the Operator's Manual isnot with the equipment, contact your dealer or M&W(217-784-4261) to obtain a Free copy before operating theequipment.

M&W®1020 South Sangamon Ave.Gibson City, Illinois 60936217-784-4261

ROUND BALERS4 x 4

Revised 09-17-01 Part No. 4904WP

MODEL 4407 & 4497SERIAL NUMBERS 20000 - CURRENT

TO THE OWNER/OPERATOR/DEALERAll implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator whorecognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement tobe used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Formin full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Cardand on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophicfailure with possible injury or death.

PARTSSECTION

Parts Section – 1

Parts Section – 2©2004 Alamo Group Inc.

PARTS ORDERING GUIDE

For maximum safety and to guarantee optimum product reliability, always usegenuine Alamo Group Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death. Directany questions regarding parts to:

The following instructions are offered to help eliminate needless delay and error in processingpurchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basicmachine featured in this manual. Part Numbers and Descriptions are given to help locate the partsand quantities required.

2. The Purchase Order must include the name and address of the person or organization orderingthe parts, who should be charged, and if possible, the serial number of the machine for which theparts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct partnumber, and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and aresubject to special handling. Request a quotation for such parts before sending a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

NOTE: Please refer to The Safety Section in the front of this Manual for the proper PartNumber when ordering Replacement Safety Decals.

M&W1020 South Sangamon Ave.Gibson City, Illinois 60936217-784-4561

PART NAME INDEX

AXLE & TIRE ASSEMBLY ................................................................................................................................................... 16BALE RAMP EXTENSION ................................................................................................................................................... 47BALER COUNT SENSOR - 4497 BALER............................................................................................................................ 48BULGE ROLLER & BELT CONVEYOR (OPTIONAL) ......................................................................................................... 88DECAL LOCATION GUIDE .................................................................................................................................................... 4DRIVELINE CV 540 RPM - OPTIONAL............................................................................................................................... 42DRIVELINE 540 RPM........................................................................................................................................................... 40DUAL TWINE DRIVE ASSEMBLY ....................................................................................................................................... 28DUAL TWINE TIE SYSTEM ................................................................................................................................................. 24ELECTRICAL SCHEMATIC - 4407 ...................................................................................................................................... 45ELECTRICAL SCHEMATIC - 4497 ...................................................................................................................................... 46ELECTRICAL SYSTEM - 4407 ............................................................................................................................................ 44ELEVATOR........................................................................................................................................................................... 92FRONT CHAMBER................................................................................................................................................................. 6FRONT SHIELDS ................................................................................................................................................................... 8GEARBOX ............................................................................................................................................................................ 38HYDRAULIC CYLINDER ...................................................................................................................................................... 19HYDRAULIC CYLINDER P/N 1410151................................................................................................................................ 17HYDRAULIC CYLINDER P/N 1410153................................................................................................................................ 18HYDRAULIC KNIFE ENGAGEMENT KIT #1450448 & HYDRAULIC CYLINDER #1457137 (OPTIONAL) ................. 82, 83HYDRAULIC SYSTEM ......................................................................................................................................................... 20KNIFE ENGAGEMENT ASSEMBLY (OPTIONAL)............................................................................................................... 80OPTIONAL - WINDROW GATHERING WHEEL (KIT #1450437) ....................................................................................... 52PICK-UP................................................................................................................................................................................ 36PICKUP FLOTATION ........................................................................................................................................................... 22REAR CHAMBER ................................................................................................................................................................. 10REAR LATCHES .................................................................................................................................................................. 12ROLLER................................................................................................................................................................................ 14SILAGE MASTER CHOPPER (OPTIONAL) ........................................................................................................................ 78SILAGE MASTER CUT-OUT CLUTCH 540 RPM (OPTIONAL) (P/N 1416677) ................................................................. 87SILAGE MASTER DRIVELINE 540 RPM WITH CUT-OUT CLUTCH - (OPTIONAL) (P/N 1456415) ................................ 86SILAGE MASTER DRIVELINE 540 RPM WITH FRICTION DISC CLUTCH - (OPTIONAL) (P/N 1456404)...................... 84SILAGE MASTER FRICTION DISC CLUTCH 540 RPM (OPTIONAL) (P/N 0921000460)................................................. 85SILAGE MASTER PICK-UP FRAME ASSEMBLY (OPTIONAL) ......................................................................................... 68SILAGE MASTER PICK-UP FRAME COMPONENTS (OPTIONAL)................................................................................... 70SILAGE MASTER RIGHT SIDE DRIVE COMPONENTS (OPTIONAL) .............................................................................. 74STANDARD SAFETY LIGHTS ............................................................................................................................................. 50TONGUE................................................................................................................................................................................. 9WIDE PICK-UP FRAME ASSEMBLY (OPTIONAL) ............................................................................................................. 60WIDE PICK-UP FRAME COMPONENTS (OPTIONAL)....................................................................................................... 64WIDE PICK-UP REEL (OPTIONAL) SILAGE MASTER PICK-UP REEL (OPTIONAL) ...................................................... 66WIRE HARNESS ROUTING - 4407..................................................................................................................................... 54WIRE HARNESS ROUTING - 4497............................................................................................................................... 56, 58WRAP INSERT ..................................................................................................................................................................... 30WRAP ROLL MOUNTING SYSTEM - MODEL 4497........................................................................................................... 34

4407 & 4497 Baler (Sep-01)

©2004 Alamo Group Inc. Parts Section – 3

DECAL LOCATION GUIDE

4407 & 4497 Baler (Sep-01)


DECAL LOCATION GUIDE

ITEM PART NO. QTY. DESCRIPTION

1 1458316 2 SAFETY OPERATION2 1458317 4 DANGER - TAILGATE3 00756004 1 IID SHIELD (INNER DECAL) - NOT SHOWN4 00756005 1 IID SHIELD (OUTER DECAL) - NOT SHOWN5 1438339 3 DANGER - SHARP KNIFE6 1458367 1 DOOR SAFETY LOCK VALVE7 1458362 1 WARNING - BALER UPSET8 00725746 1 PELIGRO9 02962764 6 PINCH POINTS10 00756059 3 WARNING - OIL LEAK11 1438330 1 CAUTION OPERATING12 D103 1 PTO SPEED - 540 RPM13 2738332 2 REFLECTOR - RED OBLONG14 5W118 1 SLOW MOVING VEHICLE15 1438326 1 DOG CLUTCH16 1458351 1 ELEVATOR CHAIN ADJUSTMENT17 1458389 1 DUAL TWINE INSTALLATION18 1458310 1 PICKUP CRANK DIRECTION19 1458311 1 PICKUP HEIGHT POSITION20 1428302 2 FILL LINE21 1438333 12 GREASE - 10 HRS22 1438303 1 PICKUP PIN23 1438319 2 OIL24 1458366 1 CONTROL HOUSING (4407 ONLY) - NOT SHOWN25 1458364 2 OIL CHAIN - 4 HRS26 1458387 1 MODEL # 4407, RIGHT

1458390 1 MODEL # 4497, RIGHT27 1458388 1 MODEL # 4407, LEFT

1458391 1 MODEL # 4497, LEFT28 1438310 2 LARGE M&W,29 1458385 1 M&W LOGO, RIGHT30 1458386 1 M&W LOGO, LEFT31 1458338 1 FRONT STRIPE32 1458339 2 REAR STRIPE33 1458368 1 NET ROUTING (4497 ONLY)34 1458371 1 WARRANTY - ELEVATOR BARS & CHAIN35 1458380 1 MADE IN USA36 1458381 1 WARNING - BALE EJECTION37 1458382 5 WARNING - HAND PINCH38 1458383 1 WARNING - TOWING SPEED39 1458384 2 PICKUP FLOAT40 1458340 1 BELT PATH (4497 ONLY)41 1458341 1 ROLL TENSION (4497 ONLY) - NOT SHOWN42 999001 1 CAUTION - STEERAGE43 00763977 1 NOTICE TO OWNER44 00771039 1 CAUTION - GENUINE PARTS45 NFS 1 SERIAL NO. PLATE46 00773723 1 DRIVELINE SAFETY - SPANISH TRANSLATION47 00776031 1 CANISTER MANUAL48 32901C 2 LOCKNUT49 00024100 4 FLATWASHER50 00021400 2 BOLT51 4904WC 1 MANUAL FOR CANISTER52 00776481 1 INSTRUCT DECAL - MANUAL OPERATOR’S INSIDE

4407 & 4497 Baler (Sep-01)


FRONT CHAMBER

4407 & 4497 Baler (Sep-01)


FRONT CHAMBER


1 1462324 1 TWINE BOX FLOOR2 1452563 2 TWINE DIVIDER ROD3 5E805 2 TYRAP4 1458703 2 RUBBER STOP5 31102H5C 28 BOLT6 00023500 10 FLATWASHER7 6D9016 35 FLANGED WHIZ LOCKNUT8 1458702 1 RUBBER HOLD-DOWN STRAP9 1431556 2 TWINE GUIDE BUSHING10 1438203 2 RETAINING RING11 1452049 1 LOWER DIVIDER PANEL12 00011700 13 LOCKWASHER13 1410145 1 UPPER DIVIDER PANEL W/ INSERTS14 1451936 1 HOLE COVER (4407 ONLY)15 37021H5C 4 CARRIAGE BOLT16 00021800 6 HEX NUT17 1430263 1 HINGE PLATE ASSEMBLY (INCLUDES ITEM 18)18 42066 1 ROLL PIN19 3267F4C 10 PHILLIPS FLATHEAD MACHINE SCREW20 1432500 2 HINGE PIN21 10119000 2 BOLT22 49072 2 COTTER PIN23 32902C 2 HEX LOCKNUT24 1436016 2 ROLLER BEARING25 312010H8C 2 BOLT26 32943C 4 ELASTIC STOP NUT27 1458417 A/R HEX INSERT (INCLUDED IN ITEM 13)28 1460275 1 TWINE BALL SEPARATOR29 1462332 1 TWINE SUPPORT, RIGHT30 1462333 1 TWINE SUPPORT, LEFT31 00035900 4 BOLT32 00011100 2 FLATWASHER

1450420 A/R HEX INSERT REPAIR KIT (INCLUDES 5 OF ITEM 27)

4407 & 4497 Baler (Sep-01)


FRONT SHIELDS


1 1460265 1 CHAIN DOOR, RH2 1451568 2 CHAIN DOOR ROD3 1450286 1 TWINE BOX LID4 1455801 1 TWINE BOX HINGE5 1410146 1 TWINE BOX COVER W/ INSERTS6 3263N4C 18 PANHEAD SCREW7 329023C 18 HEX LOCKNUT8 00035900 16 BOLT9 00023500 24 FLATWASHER10 6D9016 12 FLANGED WHIZ LOCKNUT11 00011700 4 LOCKWASHER12 1458601 2 GAS SPRING ASSEMBLY W/ BALL STUDS13 1460266 1 CHAIN DOOR, LH14 32902C 4 HEX LOCKNUT15 1458413 2 FLEXIBLE DRAW LATCH16 3263N13C 6 PANHEAD SCREW17 360015C 6 EXTERNAL TOOTH LOCKWASHER18 63121700 6 HEX MACHINE NUT19 1452300 1 CROSS BEAM COVER20 1431563 2 COVER MOUNT STUD21 00001200 8 HEX NUT22 1458417 A/R HEX INSERT (INCLUDED IN ITEM 5)

1450420 A/R HEX INSERT REPAIR KIT (INCLUDES 5 OF ITEM 22)23 1451965 1 HOSE END HANGER24 6D9007 2 SHEET METAL SCREWS

4407 & 4497 Baler (Sep-01)


TONGUE


1 1460258 1 TONGUE2 00724680 1 JACK STAND, SIDE WIND3 1431565 1 SHAFT TRANSPORT SUPPORT4 40010000 1 COTTER PIN5 00757908 1 SAFETY CHAIN6 02025700 1 BOLT7 00002701 5 FLATWASHER8 32908C 1 HEX LOCKNUT9 02931300 2 BOLT10 32948C 4 ELASTIC STOP NUT11 1451581 2 ADJUSTING BLOCK12 30079H5C 2 BOLT13 31709H5C 2 BOLT14 35009C 2 LOCKWASHER15 00000200 2 HEX NUT

4407 & 4497 Baler (Sep-01)


REAR CHAMBER

4407 & 4497 Baler (Sep-01)


REAR CHAMBER


1 6D9001 14 SHEET METAL SCREW2 1462328 1 CHAIN GUARD, REAR UPPER3 1410148 1 CHAIN GUARD W/ INSERTS, REAR MIDDLE4 1410147 1 CHAIN GUARD W/ INSERTS, REAR LOWER5 00035900 10 BOLT6 00011700 10 LOCKWASHER7 00023500 10 FLATWASHER8 1430263 1 HINGE PLATE ASSEMBLY (INCLUDES ITEMS 9 & 10)9 1432515 1 HINGE PIN10 42066 1 ROLL PIN11 3267F4C 10 PHILLIPS FLATHEAD MACHINE SCREW12 6D9016 10 FLANGED WHIZLOCK NUT13 1435500 2 BEARING CASTING14 1416000 2 BUSHING15 00749130 4 BOLT16 15B800 4 LOCKWASHER17 00001800 4 HEX NUT18 1451124 2 SAFETY LIGHT BRACKET19 1422182 4 MOUNTING STRAP20 1420105 1 HEX TANK ASSEMBLY. LH21 1420104 1 HEX TANK ASSEMBLY, RH (NOT SHOWN)22 1426783 ref CAP23 37013H5C 8 CARRIAGE BOLT24 11D9005 8 FLANGED WHIZ LOCKNUT25 1427302 2 VINYL TUBE26 1426784 2 Y-CONNECTOR27 600321 2 INSULATED CLAMP28 3263N9C 2 PANHEAD SCREW29 380413C 2 FLATWASHER30 360015C 2 EXTERNAL TOOTH LOCKWASHER31 63121700 2 HEX MACHINE NUT32 1458417 A/R HEX INSERT (INCLUDED IN ITEMS 3 & 4)

1450420 A/R HEX INSERT REPAIR KIT (INCLUDES 5 OF ITEM 32)33 1452212 1 SHIELD, RIGHT REAR UPPER HINGE34 1452213 1 SHIELD, LEFT REAR UPPER HINGE

4407 & 4497 Baler (Sep-01)


REAR LATCHES

4407 & 4497 Baler (Sep-01)


REAR LATCHES


1 1460262 1 SPRING ADJUST LEVER WELDMENT, LH2 1460261 1 SPRING ADJUST LEVER WELDMENT, RH3 00748823 2 BOLT4 00001300 2 LOCKWASHER5 00002700 4 FLATWASHER6 1454906 2 LEVER PIVOT SPACER7 000644 2 CARRIAGE BOLT8 6D9017 4 FLANGED WHIZ LOCKNUT9 00011100 6 FLATWASHER10 300518H5C 2 HEX TAP BOLT11 1431566 2 SPRING ANCHOR PIN12 33115C 2 HEX JAM NUT13 1450144 2 LATCH SPRING ASSEMBLY14 1451075 2 LATCH BAR15 00752658 2 BOLT16 00010300 2 LOCKWASHER17 00001400 2 FLATWASHER18 1434868 2 LATCH PIVOT BUSHING19 00007000 2 BOLT20 41954 2 CLEVIS PIN21 40010000 2 COTTER PIN22 000640 2 HEX LOCKNUT23 1458432 2 ADJUSTABLE YOKE END24 02816800 6 HEX NUT25 1460353 2 LATCH LIFT ROD26 1452584 2 UPPER CYLINDER PIN27 49053 4 COTTER PIN28 15B1600 6 FLATWASHER29 1460294 2 YOKE WELDMENT30 1451578 2 TRUNNION31 1457439 2 COMPRESSION SPRING32 380434C 2 FLATWASHER

4407 & 4497 Baler (Sep-01)


ROLLER

4407 & 4497 Baler (Sep-01)


ROLLER


1 1451368 1 CHAIN IDLER ARM, RH2 31709H5C 1 BOLT3 00002701 2 FLATWASHER4 32907C 1 HEX LOCKNUT5 00001400 5 FLATWASHER6 1456361 1 IDLER SPROCKET7 00703200 1 BOLT8 1457435 1 TORSION SPRING9 1454895 1 IDLER ARM PIVOT BUSHING10 1451082 1 IDLER ARM STOP, RH11 32908C 1 HEX LOCKNUT12 37022H5C 2 CARRIAGE BOLT13 00011700 2 LOCKWASHER14 00021800 2 HEX NUT15 1452558 1 ROLLER SHAFT16 1456350 2 SPROCKET17 000130 26 BOLT18 03101646 36 LOCKWASHER19 1458411 3 MACHINE BUSHING20 6D5105 2 BEARING CARTRIDGE21 1455500 2 ROLLER HUB22 1460256 1 ROLLER23 1456202 1 ROLLER CHAIN (STANDARD 4 FT. PICK-UP ONLY)

1456225 1 ROLLER CHAIN (WIDE PICK-UP ONLY)24 6D5249 2 CONNECTOR LINK25 1450311 1 PICKUP SUPPORT, LH26 1457422 1 LEAF SPRING27 1427420 1 COMPRESSION SPRING28 00059900 1 BOLT29 00011100 8 FLATWASHER30 000640 1 HEX LOCKNUT31 1451988 1 WINDROW SIDE SHIELD, LH32 1451987 1 WINDROW SIDE SHIELD, RH (NOT SHOWN)33 1460295 1 BALE BULGE REDUCER34 00753642 2 BOLT35 00013901 12 HEX NUT36 1452075 1 BALE SIZER - LH37 1452074 1 BALE SIZER-RH (NOT SHOWN)38 1451253 1 ROLLER POSITIONING PLATE39 35009C 1 LOCKWASHER40 00000200 1 HEX NUT41 00010300 2 LOCKWASHER42 7A10118 2 BOLT43 1456224 1 ROLLER CHAIN44 37031H5C 8 CARRIAGE BOLT

4407 & 4497 Baler (Sep-01)


AXLE & TIRE ASSEMBLY


1 1460244 2 SPINDLE MOUNT2 02959391 8 BOLT3 35009C 8 LOCKWASHER4 00000200 8 HEX NUT5 1452507 2 SPINDLE W/ HOLE6 312013H5C 2 BOLT7 000640 2 HEX LOCKNUT8 49033 2 COTTER PIN9 0536800W 2 SEAL10 0536005 2 BEARING CONE11 0536004 2 BEARING CUP12 0530179 2 HUB & CUP ASSEMBLY (INCLUDES ITEMS 11 & 13)13 0536002 2 BEARING CUP14 0536003 2 BEARING CONE15 380451C 2 FLATWASHER16 33099C 2 HEX SLOTTED NUT17 0527600 2 WHEEL18 0527802 2 TIRE19 0536700 2 HUB CAP20 TR415 2 VALVE STEM21 0538400 12 DRIVE STUD22 00750614 12 STUD NUT

4407 & 4497 Baler (Sep-01)


HYDRAULIC CYLINDER P/N 1410151


1410151 - HYDRAULIC CYLINDER1 5JRC12160 1 NUT HEX2 2417166 2 THD PROT 9/16-18 UNF ORB PLSTC3 1 SEAL HALLITE 605 ROD4 1 SEAL PSP PISTON RING5 1 SEAL 073-224 BU WASHER POLYU6 1 O-RING7 1 SEAL WIPER8 1417144 1 CYL HEAD9 1417145 1 TUBE WELDMT10 1417146 1 ROD WELDMT11 1417141 1 PISTON12 02975528 1 SEAL KIT(CONSIST OF ALL WITH A *)

4407 & 4497 Baler (Sep-01)


HYDRAULIC CYLINDER P/N 1410153


1410153 - HYDRAULIC CYLINDER1 1 SEAL2 1 O-RING3 1 SEAL4 1 SEAL5 1 WEAR RING6 1417147 1 CYLINDER HEAD7 1417148 1 TUBE WLDMT8 1417149 1 ROD WLDMT9 02975532 1 SEAL KIT (CONSIST OF THOSE MARKED WITH *)10 00756059 1 DECAL-WARNING OIL LEAK (NOT SHOWN)

4407 & 4497 Baler (Sep-01)


HYDRAULIC CYLINDER


1 1417136 1 BARREL ASSEMBLY2 1417126 1 FULL LOCKNUT3 1417132 1 PISTON4 1 PISTON SEAL5 1 O-RING6 1417131 1 ROD ASSEMBLY7 1 O-RING8 1 BACK-UP9 1417123 1 LOCK WIRE10 1417130 1 HEAD11 1 O-RING12 1 BACK-UP13 1 ROD WIPER14 1417133 ref SEAL KIT (INCLUDES ALL ITEMS MARKED *)

1457129 - HYDRAULIC CYLINDER, COMPLETE

4407 & 4497 Baler (Sep-01)


HYDRAULIC SYSTEM

4407 & 4497 Baler (Sep-01)


HYDRAULIC SYSTEM


1 1457130 1 HYDRAULIC LINE, UPPER RIGHT2 1457127 1 HYDRAULIC LINE, LOWER RIGHT3 1457131 1 HYDRAULIC LINE, UPPER LEFT4 1457128 1 HYDRAULIC LINE, LOWER LEFT5 2727202 1 HYDRAULIC HOSE (4497 ONLY)W/PIPE THREADED ENDS

1457214 1 HYDRAULIC HOSE W/FEMALE SWIVEL ONE END6 1457207 1 HYDRAULIC HOSE7 1457206 1 HYDRAULIC HOSE8 1457211 2 HYDRAULIC HOSE9 1457204 2 HYDRAULIC HOSE10 1457129 2 HYDRAULIC CYLINDER W/LOCK WIRE HEAD RETAINER

1410151 2 HYDRAULIC CYLINDER W/THREADED HEAD11 1432525 2 CYLINDER PIN, LOWER12 00755153 4 COTTER PIN13 1457350 1 DOOR LOCK VALVE14 311010H5C 2 BOLT15 6D9016 2 FLANGED WHIZ LOCKNUT16 1457104 7 MALE ELBOW17 2437107 1 UNION TEE18 1438418 7 2-TWIN CLAMP HALVES19 1438419 7 TWIN COVER PLATE20 10121000 7 BOLT21 1438420 1 TWIN WELD PLATE22 1458704 1 GROMMET (4497 ONLY)23 15007 1 PIPE BUSHING (4497 ONLY)24 17003 2 PIPE CAP (4407 ONLY)

3 PIPE CAP (4497 ONLY)

4407 & 4497 Baler (Sep-01)


PICKUP FLOTATION

4407 & 4497 Baler (Sep-01)


PICKUP FLOTATION


1 1451964 2 SPRING HOUSING2 37021H5C 4 CARRIAGE BOLT3 6D9016 4 FLANGE WHIZ LOCKNUT4 1451313 2 SPRING HOOK5 1437433 2 COMPRESSION SPRING6 1451576 2 SPRING PLUG7 1460238 2 SPECIAL BOLT WELDMENT8 00011100 4 FLATWASHER9 1451312 2 SPECIAL NUT10 000640 3 HEX LOCKNUT11 60042 5 WIRE ROPE CLAMP (4407 ONLY)

4 WIRE ROPE CLAMP (4497 ONLY)12 1435502 5 CABLE PULLEY13 42121 2 ROLL PIN14 00749130 1 BOLT15 00002700 2 FLATWASHER16 32905C 2 HEX LOCKNUT17 1460139 1 PICKUP CRANK ASSY (INCLUDES ITEMS 18 - 20)18 1451371 1 PICKUP LIFT CRANK19 1454869 1 PICKUP LIFT CRANK HANDLE20 1458414 1 WASHER CUP PUSH NUT21 1460269 1 PICKUP LIFT SCREW22 49054 1 COTTER PIN23 1458425 1 THRUST WASHER24 1461206 1 PICKUP SCREW SUPPORT25 1450242 1 PICKUP LIFT CABLE ARM26 000130 2 BOLT27 6D9017 2 FLANGED WHIZ LOCKNUT28 00059900 1 BOLT29 1461209 1 PICKUP LIFT CONNECTOR (4497 ONLY)30 02845600 1 BOLT (4497 ONLY)31 1454864 1 TUBE SPACER (4497 ONLY)32 00001000 2 WIRE ROPE CLAMP (4407 ONLY)

3 WIRE ROPE CLAMP (4497 ONLY)33 1451254 1 CABLE PLATE (4497 ONLY)34 33007C 1 HEX NUT (4497 ONLY)35 1437100 1 PICKUP HYDRAULIC CYLINDER (4497 ONLY) W/PIPE PORT

1410153 1 PICK-UP HYDRAULIC CYLINDER(4497 ONLY) W/ORING BOSS PORT36 1457126 1 ADAPTER UNION (4497 ONLY) W/PIPE THREADS

02960018 1 ADAPTER HYDRAULIC ELBOW(4497 ONLY) W/O-RING37 32907C 2 HEX LOCKNUT (4497 ONLY)38 02788400 1 BOLT39 1457413 1 PICKUP CABLE (4497 ONLY)40 1457407 1 PICKUP CABLE (4407 ONLY)41 29N132 1 CABLE THIMBLE (4407 ONLY)42 00726195 1 PIPE

4407 & 4497 Baler (Sep-01)


DUAL TWINE TIE SYSTEM

4407 & 4497 Baler (Sep-01)




1 1435501 3 BEARING HOUSING2 1436005 6 BALL BEARING3 1436362 1 SPROCKET IDLER SHAFT4 1438204 5 RETAINING RING5 1436350 1 SPROCKET DRIVE SHAFT6 1436425 1 GEAR SHAFT/PINION7 1436001 2 BUSHING8 1460155 1 RH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10)9 1458418 2 PERMANENT STUD10 42082 2 ROLL PIN11 1460156 1 LH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10)12 1450164 1 CHAIN COVER STUD ASSEMBLY (INCLUDES 4 OF ITEM #55)13 1450324 1 RH TWINE TRAVEL LIMIT14 1450325 1 LH TWINE TRAVEL LIMIT15 1451174 4 KNIFE STRAP16 31104H5C 2 BOLT17 00021800 14 HEX NUT18 37021H5C 6 CARRIAGE BOLT19 6D9016 8 FLANGED WHIZLOCK NUT20 1450363 1 CHAIN BEAM21 1451048 2 TWINE HOOK-WHITE22 1451173 2 LATCH, TRAVEL23 1451175 2 KNIFE CARRIER24 1451353 1 CHAIN GUIDE25 1451569 2 SPACER, KNIFE CARRIER27 1456215 2 ROLLER CHAIN28 1456782 4 SLIDER29 1457427 2 EXTENSION SPRING30 1458409 1 CARRIAGE BOLT31 10062000 8 BOLT32 31102H5C 9 BOLT33 00035900 4 BOLT34 10119000 3 BOLT35 10121000 2 BOLT36 32901C 2 HEX LOCKNUT37 32902C 8 HEX LOCKNUT38 32942C 2 ELASTIC STOP NUT39 00024000 6 HEX NUT40 33111C 2 HEX JAM NUT41 00017000 6 LOCKWASHER42 00011700 12 LOCKWASHER43 370010C 4 INTERNAL TOOTH LOCKWASHER45 37022C 3 CARRIAGE BOLT47 380419C 8 FLATWASHER48 6D5206 2 CONNECTING LINK49 6D5283 2 DOUBLE STRAND OFFSET LINK50 1436775R 1 PLASTIC GEAR51 1456783 1 DRIVE PULLEY52 00023500 5 FLATWASHER53 40621 1 KEY54 1438204 2 RETAINING RING55 1458419 4 PERMANENT STUD56 4062.56 1 KEY, GEAR57 24022 1 SHOULDER BOLT58 1457429 1 TORSION SPRING, COUNTER59 1438606 1 COUNTER60 1452192 1 COUNTER MOUNTING BRACKET61 3272P5C 4 MACHINE SCREW62 33025C 4 HEX MACHINE NUT63 37003C 4 INTERNAL TOOTH LOCKWASHER64 1452193 1 COUNTER COVER65 1430193 2 KNIFE BLADE ASSEMBLY

4407 & 4497 Baler (Sep-01)



4407 & 4497 Baler (Sep-01)




66 3263R2C 4 PHILLIP HEAD SCREW67 1450166 1 TWINE DRIVE ASSEMBLY68 1451930 1 TWINE GUIDE BRACKET69 1431556 2 TWINE GUIDE BUSHING70 1438203 2 RETAINING RING71 00021400 2 BOLT72 11D9005 2 FLANGED WHIZLOCK NUT73 340211C 2 WING NUT74 1437426 2 COMPRESSION SPRING75 1452184 2 DUAL TWINE BRAKE76 1458409 2 CARRIAGE BOLT77 1438205 3 RETAINING RING

4407 & 4497 Baler (Sep-01)


DUAL TWINE DRIVE ASSEMBLY

4407 & 4497 Baler (Sep-01)


DUAL TWINE DRIVE ASSEMBLY


1 11D9005 2 FLANGED WHIZ NUT2 1426426 1 SPUR GEAR3 1427050 1 ELECTRIC MOTOR4 1451628 1 MOTOR MOUNT5 330211C 2 HEX MACHINE NUT6 360014C 2 EXT TOOTH LOCKWASHER7 42035 1 ROLL PIN8 1434851 2 BEARING CAGE9 1436002 2 BEARING10 1438200 2 RETAINING RING11 1438202 2 RETAINING RING12 1450367 1 LOWER IDLER ARM13 1452532 2 IDLER SHAFT14 31075C 2 BOLT15 1450368 1 UPPER IDLER ARM16 1436003 1 BEARING17 1436005 1 BEARING18 1452530 1 SHAFT, FEED ROLLER19 1452531 1 FEED ROLLER, DUAL TWINE20 1456425 1 MODIFIED SPUR GEAR21 1458200 1 EXTERNAL RETAINING RING22 10058000 3 BOLT23 00017000 6 LOCKWASHER24 1450366 1 MOUNTING BRACKET25 1457428 2 EXTERNAL SPRING26 31002H5C 3 BOLT27 314017C 1 BOLT28 00001200 1 HEX NUT30 1431556 2 TWINE GUIDE BUSHING31 1438203 2 RETAINING RING32 1451930 1 TWINE GUIDE BRACKET33 00024100 2 FLATWASHER34 37021H5C 2 CARRIAGE BOLT35 6D90163 2 FLANGED WHIZ LOCKNUT36 00021400 2 BOLT

4407 & 4497 Baler (Sep-01)


WRAP INSERT

4407 & 4497 Baler (Sep-01)


WRAP INSERT


1 1456300 1 PULLEY2 3919A2C 2 SOCKET HEAD SETSCREW3 1456103 1 V-BELT4 00002700 4 FLATWASHER5 2F031 2 BELT IDLER6 00749130 2 BOLT7 00999418 1 BOLT8 32905C 4 LOCKNUT9 1451270 1 IDLER PULLEY ARM10 1454879 1 IDLER BUSHING RS11 1457436 1 TORSION SPRING CLUTCH12 1452049 1 PANEL, LOWER DIVIDER13 00021800 39 NUT14 00011700 37 LOCKWASHER15 00002000 3 BOLT16 03101646 5 LOCKWASHER17 1432034 3 CLUTCH RETAINING WASHER18 6D5103A 10 FLANGETTE19 6D5113 5 BEARING20 1451186 1 CLUTCH BRACKET21 37021H5C 21 CARRIAGE BOLT22 1452533 1 CAM SHAFT23 00035900 5 BOLT24 1451121 1 BRACKET, HALL EFFECT25 1457932 1 CLUTCH - MODIFIED26 1454885 2 SPACER27 1450195 1 CUT-OFF CAM27A 1450372 1 CAM27B 3919A9C 3 SOCKET HEAD SETSCREW27C 5C5180 3 JAM NUT27D 42069 1 ROLL PIN28 1452198 1 BRACKET, CAM SWITCH29 00023500 5 FLATWASHER31 6D9016 1 FLANGE SERRATED LOCKNUT32 MWSN1192 2 EXTENSION SPRING33 1450393 2 IDLER ARM BASE34 1450374 2 SWING ARM35 1438203 2 RETAINING RING36 1460103 1 IDLER ROLLER36A 1456007 2 BEARING36B 1454881 1 IDLER ROLLER37 1450376 1 NET CHUTE38 1450176 1 DRIVE ROLLER39 1460208 1 END PLATE RH40 10119000 2 BOLT41 1460100 1 COUNTER RING42 1450177 1 TRIP ARM42A 1436016 1 ROLLER BEARING42B 1450378 1 TRIP ARM43 00023100 2 BOLT44 000640 1 LOCKNUT45 02044900 1 BOLT46 1454884 1 STOP, TORSION SPRING47 1458707 1 BUMPER48 40010000 2 COTTER PIN49 1457431 1 TORSION SPRING, RH50 1460102 1 CUTTER BAR50A 1428350 4 KNIFE50B 3981H1C 10 BOLT50C 380419C 10 FLATWASHER50D 1450373 1 CUTTER BAR51 1454880 1 IDLER BUSHING LS

4407 & 4497 Baler (Sep-01)


WRAP INSERT

4407 & 4497 Baler (Sep-01)


WRAP INSERT


52 1457430 1 TORSION SPRING, LH53 1456102 1 V-BELT54 00748823 1 BOLT55 1456011 2 FLANGETTE56 1456012 1 BEARING57 1457902 1 CLUTCH58 312020H5C 1 BOLT59 6D9017 3 FLANGE SERRATED LOCKNUT60 1450188 1 END PLATE, LH61 00011100 2 FLATWASHER62 00013901 2 HEX NUT63 1454894 1 SPACER64 1461207 1 IDLER PULLEY ARM, RS65 380434C 1 FLATWASHER66 1451115 1 BELT TENSIONER BRACKET

4407 & 4497 Baler (Sep-01)


WRAP ROLL MOUNTING SYSTEM - MODEL 4497

4407 & 4497 Baler (Sep-01)


WRAP ROLL MOUNTING SYSTEM - MODEL 4497


1 70014W 1 PLASTIC KNOB2 1450275 1 ROLL LATCH HANDLE3 1450276 1 HANDLE PIVOT BRACKET4 00035900 6 BOLT5 6D9016 6 FLANGED WHIZ LOCKNUT6 42049 1 ROLL PIN7 1451561 1 TENSION ROD8 1438447R 1 HOIST EYE9 00024000 2 HEX NUT10 1427422 1 EXTENSION SPRING11 31006H5C 1 BOLT12 11D9005 2 HEX FLANGE NUT13 1450600 2 ROLL TUBE MOUNTING14 1450272 1 ROLL MOUNTING TUBE15 1455503 2 ROLL END STOP16 1451916 3 SPACER WASHER (USE ONLY AS NEEDED)17 1450271 1 ROLL LATCH18 1426789 A/R ROLL/NETTING

4407 & 4497 Baler (Sep-01)


PICK-UP

4407 & 4497 Baler (Sep-01)


PICK-UP


1 1432034 4 WASHER3 1460212 1 PICK-UP FRAME4 1460213 1 END PLATE, RH5 1460214 1 END PLATE, LH6 1450304 1 PICK-UP MOUNT, RH7 1450305 1 PICK-UP MOUNT, LH8 1452041 1 WINDROW GUIDE SHIELD, RH9 1452042 1 WINDROW GUIDE SHIELD, LH10 1452189 15 PICK-UP BAND11 1455505 1 PICK-UP CAM12 1456005 2 BALL BEARING13 1456006 4 BEARING FLANGETTE14 1437434 40 PICK-UP TINE, DOUBLE SPRING15 1450300 2 BEARING PLATE16 29N132 2 THIMBLE17 000130 1 BOLT18 00753642 14 BOLT19 02030700 6 BOLT20 03101646 17 LOCKWASHER21 00001300 6 LOCKWASHER22 37021H5C 4 CARRIAGE BOLT23 00023500 44 FLATWASHER24 40621.25 1 KEY25 450022 1 GREASE FITTING26 6D9003 21 SHEET METAL SCREW27 6D9007 45 HEX FLANGE SCREW28 6D9016 4 FLANGE WHIZ LOCKNUT29 00013901 10 HEX NUT30 1460211 1 PICK-UP SHAFT31 1451095 5 TINE BAR CAM ARM32 1451114 40 TINE SUPPORT ANGLE33 1451739 40 PICK-UP TINE34 1456004 5 BALL BEARING35 02845500 5 BOLT36 32907C 5 HEX LOCKNUT37 701515C 5 FLATWASHER38 32972H5C 40 HEX LOCKNUT39 37027H5C 40 CARRIAGE BOLT40 02970595 5 BOLT41 00007000 5 BOLT42 380460C 5 FLATWASHER43 1456002 10 BUSHING44 1456003 10 BUSHING45 1460210 5 TINE BAR46 31202H5C 2 BOLT47 00015800 10 HEX LOCKNUT

4407 & 4497 Baler (Sep-01)


GEARBOX

4407 & 4497 Baler (Sep-01)


GEARBOX


1 1416658 1 CASING2 2716659 2 SHIM3 2716602 2 BEARING4 1416659 1 SHAFT5 2716740 1 SNAP RING6 00752931 1 PLUG7 2716658 2 BEARING8 2716607 2 SNAP RING9 2716660 3 OIL SEAL10 1416660 1 CROWN WHEEL11 2716662 2 SHIM12 70809C8 4 BOLT13 1416661 1 EXTENSION14 1416662 1 PINION SHAFT15 00756649 1 SNAP RING16 61368C8 4 BOLT17 1416656 1 PLUG, DIPSTICK - LONG18 1416663 1 SHIM19 2716557 1 PLUG20 1456410 1 GEARBOX COMPLETE - LESS ITEMS 21-2821 000130 2 BOLT22 00011100 2 FLATWASHER23 1456779 1 SAFETY SHIELD24 03101646 2 LOCKWASHER25 00013901 2 HEX NUT26 00756373 4 BOLT27 00010300 4 LOCKWASHER28 710850 1 KEY

4407 & 4497 Baler (Sep-01)


DRIVELINE 540 RPM

4407 & 4497 Baler (Sep-01)


DRIVELINE 540 RPM


2 1416401 2 CROSS & BEARING KIT3 1416402 1 INBOARD YOKE4 1416404 1 INNER PROFILE5 703624 2 ROLL PIN7 1416409 2 BEARING RING8 1416410 1 OUTER SHIELD TUBE10 1416405 1 OUTER PROFILE11 1416411 1 INNER SHIELD TUBE12 1416437 2 SHIELD CONE, 5 RIBBED13 1416406 1 INBOARD YOKE14 1416589 1 CLUTCH HOUSING14A 1416590 1 GREASE FITTING15 1416583 1 QUICK DISCONNECT HUB16 1416419 14 INNER SPRING17 1416418 32 OUTER SPRING18 1416417 32 CAM19 1416443 1 SEAL RING20 1416444 1 THRUST RING21 1416422 1 RETAINER RING22 1416424 1 COMPRESSION SPRING23 1416425 1 LOCK COLLAR24 1416423 3 BALL25 1416426 1 FLANGED RING26 1416427 1 RETAINING RING27 1416588 1 RADIAL PIN CLUTCH, BI-DIRECTIONAL29 1416438 2 SCREW30 2738315 1 OUTER DECAL31 2738320 1 INNER DECAL32 1416585 1 QUICK DISCONNECT YOKE ASSEMBLY33 1416640 1 QUICK DISCONNECT REPAIR KIT

1436404 1 IID SHAFT ASSEMBLY, COMPLETE W/CLUTCH34 1416587 ref IID HALF, TRACTOR END35 1416584 ref IID HALF, BALER END (INCLUDES CLUTCH)36 1416441 1 QUICK DISCONNECT FLANGE KIT

4407 & 4497 Baler (Sep-01)


DRIVELINE CV 540 RPM - OPTIONAL

4407 & 4497 Baler (Sep-01)


DRIVELINE CV 540 RPM - OPTIONAL


1456411 - CV IID DRIVELINE ASSY1 1416644 1 SLIDE COLLAR YOKE SPLINE2 8382 1 GREASE FITTING3 1416645 1 DOUBLE YOKE4 1416646 1 INBOARD YOKE5 1416647 2 CROSS AND BEARING KIT6 703624W 2 ROLL PIN7 8925 1 CROSS AND BEARING KIT8 1416648 1 INNER SHAFT9 1416649 1 OUTER SHAFT & SLEEVE10 1416406 1 INBOARD YOKE11 1416588 1 RADIAL PIN CLUTCH12 8393 2 BEARING RING13 1416650 1 OUTER SHIELD14 1416651 1 INNER SHIELD15 1416652 1 CONSTANT VELOCITY CONE & BEARING ASSY16 1416653 1 SHIELD CONE, 3 RIBBED17 1416437 1 SHIELD CONE, 5 RIBBED19 00756005 1 DANGER DECAL, ROTATING DRIVELINE (INCLUDED IN ITEM 13)20 00756004 1 DANGER DECAL, SHIELD MISSING (INCLUDED IN ITEM 9)21 1416438 8 SCREW (INCLUDED IN ITEMS 15 - 17)22 8974 1 SUPPORT BEARING23 1416601 1 GREASE FITTING (PART OF ITEM 9)

00767953 ref SLIDE LOCK YOKE REPAIR KIT (PART OF ITEM 1)0921000470 ref QUICK DISONNECT FLANGE KIT (INCLUDES ITEMS 22-26) (PART OF ITEM 11)

24 1416654 1 IID HALF, TRACTOR END25 1416664 1 IID HALF, BALER END (INCLUDES CLUTCH)26 1416589 1 CLUTCH HOUSING27 1416590 1 GREASE FITTING (PART OF ITEM 14)28 1416583 1 QUICK DISCONNECT HUB29 1416419 14 INNER SPRING30 1416418 32 OUTER SPRING31 1416417 32 CAM32 1416443 1 SEAL RING33 1416444 1 THRUST RING34 1416422 1 RETAINER RING35 1416424 1 COMPRESSION SPRING36 1416425 1 LOCK COLLAR37 1416423 3 BALL38 1416426 1 FLANGED RING39 1416427 1 RETAINING RING40 1416674 1 SHIELD, OUTER HALF-COMPLETE (INCLUDESITEM #12,13,16,19, &21)41 1416675 1 SHIELD, INNER HALF - COMPLETE (INCLUDES ITEM # 12,14,17,21, &22)

4407 & 4497 Baler (Sep-01)


ELECTRICAL SYSTEM - 4407


1 33029C 4 HEX NUT2 37005C 8 LOCKWASHER3 380413C 4 FLATWASHER4 360015C 4 EXTERNAL TOOTH LOCKWASHER5 3276H5C 4 HEX MACHINE SCREW6 3274F10C 4 FLATHEAD MACHINE SCREW7 1431170 2 SWITCH BRACKET8 31102H5C 6 BOLT9 600321 6 CLAMP10 32902C 6 HEX LOCKNUT11 1450249 2 SWITCH HARNESS12 1457915 1 WIRE HARNESS, BALER END13 5E805 6 TYRAP14 0138629 1 TYRAP15 1456778 4 BEADED TIE16 1450175 1 CONTROL PANEL ASSEMBLY17 1451120 1 CONTROLLER BRACKET18 1456776 2 KNOB19 1458708 2 ANTI-PIVOT WASHER

4407 & 4497 Baler (Sep-01)


ELECTRICAL SCHEMATIC - 4407


4407 & 4497 Baler (Sep-01)


ELECTRICAL SCHEMATIC - 4497


4407 & 4497 Baler (Sep-01)


BALE RAMP EXTENSION


1 1450398 1 RAMP PIPE2 1450399 2 PIVOT PIN3 1452546 2 SPRING ROD4 1451582 2 TRUNNION SPRING5 1454898 4 TRUNNION BUSHING6 1460247 2 RAMP MOUNT7 1457420 2 COMPRESSION SPRING8 1458705 2 RUBBER CUSHION DONUT9 45053 2 GREASE FITTING10 00001400 2 FLATWASHER11 32907C 4 LOCKNUT12 00748823 4 BOLT13 00001300 4 LOCKWASHER14 00002700 4 FLATWASHER15 000130 2 BOLT16 03101646 2 LOCKWASHER17 00013901 2 HEX NUT18 419513 2 CLEVIS PIN19 40010000 2 COTTER PIN20 REF. ONLY 1 LOWER CROSS AXLE

4407 & 4497 Baler (Sep-01)


BALER COUNT SENSOR - 4497 BALER

4407 & 4497 Baler (Sep-01)


BALER COUNT SENSOR - 4497 BALER


1 1414201 1 BRACKET, DOOR HINGE MAGNET2 31104H5C 2 BOLT3 1457928 1 ACTUATOR4 3257N7C 2 MACHINE SCREW5 38045C 2 FLATWASHER6 37003C 2 LOCKWASHER7 33025C 2 HEX MACHINE NUT8 1457943 1 SENSOR, MAGNETIC9 3257N7C 2 MACHINE SCREW10 38045C 2 FLATWASHER11 37003C 2 LOCKWASHER12 33025C 2 HEX MACHINE NUT13 1451125 1 BRACKET, DOOR OPEN SENSOR14 3263N9C 2 MACHINE SCREW15 380413C 2 FLATWASHER16 360015C 2 LOCKWASHER17 63121700 2 HEX MACHINE NUT18 1452209 1 SHIELD, HOUSING PIVOT-LEFT

1452208 1 SHIELD, HOUSING PIVOT-RIGHT (NOT SHOWN)19 10058000 4 BOLT20 00024100 4 FLATWASHER21 11D9005 4 FLANGED LOCKNUT22 6D9016 2 FLANGED LOCKNUT23 1452208 1 SHIELD, HOUSING PIVOT - RIGHT (NOT SHOWN)

NOTE: Clearance between

4407 & 4497 Baler (Sep-01)


STANDARD SAFETY LIGHTS

4407 & 4497 Baler (Sep-01)


STANDARD SAFETY LIGHTS


1 1457937 1 DUAL LAMP (RH)2 1457938 1 DUAL LAMP (LH)3 10058000 8 BOLT4 32901C 8 LOCKNUT5 1457939 1 MAIN HARNESS6 1457944 1 WISHBONE HARNESS7 600343 3 SUPPORT CLAMP8 5E805 8 TYRAP9 2427905 A/R MALE PLUG10 2427904 A/R SPRING11 1417917 A/R AMBER LENS12 1417916 A/R RED LENS13 1417918 A/R LIGHT BULB14 1417919 A/R BLACK BLANK15 1417915 A/R FRONT HOUSING16 1417914 A/R REAR HOUSING

4407 & 4497 Baler (Sep-01)


OPTIONAL - WINDROW GATHERING WHEEL (KIT #1450437)

4407 & 4497 Baler (Sep-01)


OPTIONAL - WINDROW GATHERING WHEEL (KIT #1450437)


1 1458709 2 GATHERING WHEEL2 1451098 2 FLANGE CLAMP PLATE3 1460312 2 WHEEL HUB4 00007000 16 BOLT5 000640 16 LOCKNUT6 1460307 1 R. SPINDLE

1460308 1 L. SPINDLE7 00013900 2 BOLT8 32943C 2 ELASTIC STOP NUT9 1461009 1 R. STRIPPER & HAY STRAP

1461010 1 L. STRIPPER & HAY STRAP10 00023100 4 BOLT11 00011100 8 FLATWASHER12 03101646 8 LOCKWASHER13 00013901 8 HEX NUT14 1460310 1 R. WHEEL ARM

1460311 1 L. WHEEL ARM15 1460315 2 PIVOT PIN16 1460313 1 R. MOUNT BRACKET

1460314 1 L. MOUNT BRACKET17 00753642 4 BOLT18 10119000 2 BOLT19 00011700 2 LOCKWASHER20 00021800 2 HEX NUT21 45051 4 GREASE FITTING22 1456022 4 BUSHING23 1456023 4 BUSHING24 1452586 2 UPPER LIFT ROD25 02816800 2 HEX NUT26 1460309 2 LIFT TUBE27 1452587 2 LOWER LIFT ROD (SHORT - 12")28 1457440 2 SPRING29 42088 2 ROLL PIN30 40010000 2 COTTER PIN31 00002700 2 FLATWASHER32 49207 2 HAIR PIN COTTER33 1458431 2 THRUST WASHER34 1438442 2 MACHINE BUSHING35 00034300 2 RETAINING RING

4407 & 4497 Baler (Sep-01)


WIRE HARNESS ROUTING - 4407

4407 & 4497 Baler (Sep-01)




1 00035900 34 BOLT2 1457915 1 WIRE HARNESS-BALER END3 1457944 1 WIRE HARNESS, WISHBONE4 5E805 10 TY RAP5 600321 10 SUPPORT CLAMP6 6D9016 20 WHIZLOCK NUT7 1462353 2 SUPPORT, HARNESS

4407 & 4497 Baler (Sep-01)



4407 & 4497 Baler (Sep-01)




1 00035900 34 HHCS 5/16-18UNC 3/4 PL52 1450196 1 ASY,CAM SWITCH3 1456777 2 WIRE CLAMP, 1/2 PLASTIC ADHESI4 1457929 1 WIRE HARNESS,BALER KN-SYSTEM5 1457932 1 CLUTCH ASY-GT-MODIFIED6 1457942 1 HARNESS,HALL EFFECT7 1457944 1 WIRE HARNESS,WISHBONE8 1458424 2 NUT,HEX NYLON JAM 1/2-139 5E805 10 TY RAP, .091 WIDE X 8 LONG-BLA10 600321 10 SUPPORT CLAMP, .312 ID X .34411 6D9016 29 FLG WHIZLOCK NUT 5/16-1812 1462353 2 CHANNEL,HARNESS SUPPORT13 3259N10C 4 PHLP SCRW PN HD 6-32 X 3/414 33029C 4 HEX MACHINE NUT #6-3215 37005C 4 INT TOOTH LOCKWASHER #6

4407 & 4497 Baler (Sep-01)



4407 & 4497 Baler (Sep-01)




1 00035900 34 BOLT2 1450196 1 CAM SWITCH3 1456777 2 WIRE CLAMP4 1457929 1 WIRE HARNESS, BALER5 1457932 1 CLUTCH6 1457942 1 HARNESS, HALL EFFECT7 1457944 1 WIRE HARNESS, WISHBONE8 1458424 2 HEX JAM NUT9 5E805 10 TY RAP10 600321 10 SUPPORT CLAMP11 6D9016 29 WHIZLOCK NUT12 1462353 2 SUPPORT, HARNESS13 3259N10C 4 SCREW14 33029C 4 MACHINE NUT15 37005C 4 LOCKWASHER

4407 & 4497 Baler (Sep-01)


WIDE PICK-UP FRAME ASSEMBLY (OPTIONAL)

4407 & 4497 Baler (Sep-01)




1 1460272 1 FRAME2 00023500 3 FLATWASHER3 1456365 2 SPROCKET4 40621.25 2 KEY5 1460280 1 END PLATE, LH6 1460279 1 END PLATE, RH7 1451991 2 AUGER SHIELD8 32947C 3 NUT9 1456005 2 BEARING10 1456006 4 BEARING FLANGETTE11 1460276 1 AUGER, RH12 1460277 1 AUGER, LH13 1460305 1 AUGER COVER, LH14 1460304 1 AUGER COVER, RH15 1436014 6 FLANGETTE16 1456019 3 BEARING17 1452573 1 JACKSHAFT18 1452574 1 SHAFT, STUB19 1451093 2 COUNTER WEIGHT BLOCK20 1451584 2 CLAMPING BLOCK21 1457438 2 SPRING EXTENSION22 1458201 2 RETAINING RING23 1452575 2 BOLT, PIVOT24 1456363 2 SPROCKET25 1456364 2 SPROCKET26 1452569 1 BOSS27 1452205 13 BAND, LONG28 1452204 10 BAND, SHORT29 1455505 1 CAM CASTING30 1454928 1 BUSHING31 1460298 1 MOUNT LH, GAUGE WHEEL32 1460297 1 MOUNT RH, GAUGE WHEEL33 1436006 4 BEARING34 6D5249 3 CONNECTOR LINK35 1456225 2 ROLLER CHAIN, RH36 1456226 1 ROLLER CHAIN, LH37 11108 1 ELBOW38 2438408 1 GREASE FITTING39 9903 1 PIPE NIPPLE40 1460283 1 STUFFER BAR41 1460352 1 STUFFER SHAFT42 1456017 2 BEARING43 1460287 1 LINK44 1436005 2 BEARING45 1438205 2 RETAINING RING46 1460285 1 IDLER ARM LS47 1461231 1 PULL48 1456362 2 SPROCKET49 00750952 1 BOLT50 00001400 2 WASHER51 1458409 1 BOLT52 1460286 1 IDLER ARM RS53 02675800 1 BOLT54 00010300 1 WASHER55 1458430 1 FLATWASHER56 40631.25 2 KEY57 40631.5 2 KEY58 40641.5 4 KEY59 6D9003 27 SCREW60 6D9017 2 LOCKNUT61 6D9007 61 SCREW62 6D9001 4 SCREW

4407 & 4497 Baler (Sep-01)



4407 & 4497 Baler (Sep-01)




63 000640 6 NUT64 6D9016 8 LOCKNUT65 03101646 23 LOCKWASHER66 00013901 18 NUT67 00011400 7 BOLT68 00001200 1 NUT69 00001300 7 LOCKWASHER70 00002700 1 FLATWASHER71 00010600 2 BOLT72 00013900 4 BOLT73 00026200 1 COTTER PIN74 00999418 1 BOLT75 02030700 6 BOLT76 300311H5C 1 BOLT77 3267N4C 4 SCREW78 32902C 1 LOCKNUT79 37021H5C 3 BOLT80 37032H5C 16 BOLT81 49208 2 HAIRPIN COTTER

4407 & 4497 Baler (Sep-01)


WIDE PICK-UP FRAME COMPONENTS (OPTIONAL)

4407 & 4497 Baler (Sep-01)


WIDE PICK-UP FRAME COMPONENTS (OPTIONAL)


1 00023500 4 FLATWASHER2 1462352 1 JACKSHAFT SHIELD3 1460300 1 SHIELD, RS UPPER4 1460301 1 SHIELD, LS UPPER5 1460302 1 SHIELD, RS LOWER6 1460303 1 SHIELD, LS LOWER7 1451667 2 PLATE, RUB8 1460351 1 SHIELD, CHAIN9 1462351 1 SHIELD, CHAIN10 1460299 2 AXLE GAUGE WHEEL11 1461003 2 HEIGHT BAR12 1460143 2 TIRE & RIM ASSEMBLY13 1456700 2 WHEEL COVER14 00002701 8 FLATWASHER15 32948C 2 LOCKNUT16 1460293 2 HOLD DOWN ARM17 1456795 2 HOLD DOWN ARM STOP18 1460292 1 HOLD DOWN19 1462335 1 BAFFLE, UPPER20 1462336 1 BAFFLE, LOWER21 1451092 2 HOLD DOWN CHAIN PLATE22 1460273 1 LIFT, RH23 1460274 1 LIFT, LH24 1461224 2 LIFT STRAP25 1461555 2 CABLE ROD26 1462337 2 LIFT SHIELD27 6D9007 11 SCREW28 6D9001 4 SCREW29 00059900 2 BOLT30 00011100 8 FLATWASHER31 000640 2 LOCKNUT32 001636 2 BOLT33 32941C 2 LOCKNUT34 1438442 2 FLATWASHER35 49036 2 COTTER PIN36 311010H5C 4 BOLT37 6D9016 12 LOCKNUT38 00035900 8 BOLT39 03101646 6 LOCKWASHER40 00013901 2 NUT41 00011400 2 BOLT42 00002000 4 BOLT43 02030700 6 BOLT44 00755153 6 COTTER PIN45 6D9018 6 LOCKNUT

4407 & 4497 Baler (Sep-01)


WIDE PICK-UP REEL (OPTIONAL) SILAGE MASTER PICK-UP REEL (OPTIONAL)

4407 & 4497 Baler (Sep-01)


WIDE PICK-UP REEL (OPTIONAL) SILAGE MASTER PICK-UP REEL (OPTIONAL)


1 1460281 5 TINE BAR2 1460282 1 PICKUP SHAFT3 1451095 5 ARM TINE BAR CAM4 1456004 5 BEARING5 1437434 60 DOUBLE TINE SPRING6 1450300 2 BEARING PLATE7 1456002 10 BUSHING8 1456003 10 BUSHING9 1451114 60 TINE SUPPORT ANGLE10 1451739 60 TINE CLIP11 37027H5C 60 BOLT12 32972H5C 60 LOCKNUT13 00023500 60 FLATWASHER14 03101646 10 LOCKWASHER15 00013901 10 NUT16 00007000 5 BOLT17 00015800 10 LOCKNUT18 00753642 10 BOLT19 02845500 5 BOLT20 02970595 5 BOLT21 32907C 5 LOCKNUT22 380460C 5 FLATWASHER23 701515C 5 FLATWASHER

4407 & 4497 Baler (Sep-01)


SILAGE MASTER PICK-UP FRAME ASSEMBLY (OPTIONAL)

4407 & 4497 Baler (Sep-01)


SILAGE MASTER PICK-UP FRAME ASSEMBLY (OPTIONAL)


1 1460333 1 FRAME2 1460134 1 REEL3 1460340 1 END PANEL - RH4 1456006 4 BEARING FLANGETTE5 1456005 2 BEARING6 1456365 2 SPROCKET7 40621.25 2 KEY8 1460323 1 PICKUP MOUNT - RIGHT9 1460285 2 IDLER ARM10 00750952 2 BOLT11 1456362 2 IDLER SPROCKET12 00001400 6 FLATWASHER13 1451685 2 TAB, SPRING HOOK14 32907C 2 NUT, LOCK15 1454928 2 BUSHING, LS IDLER PIVOT16 00002700 2 FLATWASHER17 00001300 7 LOCKWASHER18 00999418 3 BOLT19 00001200 3 NUT20 1457441 2 SPRING, TENSION21 02957009 1 BOLT22 00013901 3 NUT23 1452204 23 BAND, SHORT24 1455505 1 CAM, PICKUP25 1460341 1 END PANEL - LH26 1460324 1 PICKUP MOUNT-LEFT27 11108 1 ELBOW28 9904 1 PIPE NIPPLE29 2438408 1 GREASE FITTING30 03101646 6 LOCKWASHER31 00011400 6 BOLT32 6D9007 46 SCREW33 6D9003 27 SCREW34 00023500 2 FLATWASHER35 02030700 5 BOLT36 00011100 1 FLATWASHER37 3920A29C 4 SETSCREW38 1456225 2 ROLLER CHAIN39 6D5249 2 CONNECTOR LINK

4407 & 4497 Baler (Sep-01)


SILAGE MASTER PICK-UP FRAME COMPONENTS (OPTIONAL)

4407 & 4497 Baler (Sep-01)




1 1460380 1 SHIELD, RIGHT2 1451713 2 RUB PLATE3 6D9001 12 FLANGE SCREW4 1460381 1 SHIELD, LEFT5 1460335 1 AUGER, RH6 1460325 2 AUGER BEARING HOUSING7 37032H5C 8 BOLT, CARRIAGE8 1436006 4 BEARING9 1458201 2 RETAINING RING10 1461021 2 PICKUP MOUNT RETAINER STRAP11 02030700 4 BOLT12 32905C 4 LOCKNUT13 1456367 1 DOUBLE, SPROCKET, RS14 40631.75 1 KEY15 1460336 1 AUGER, LH16 1456366 1 SPROCKET, LH17 40631.25 1 KEY18 1460344 1 HOLD DOWN TINE19 1461038 2 HOLD DOWN STOP ANGLE20 37022H5C 4 BOLT, CARRIAGE21 32902C 8 LOCKNUT22 1456108 2 BUMPER PAD23 10119000 4 BOLT24 00023500 7 FLATWASHER25 1460293 2 HOLD DOWN ARM26 00059900 2 BOLT27 1456795 2 HOLD DOWN ARM STOP28 00011100 8 FLATWASHER29 000640 10 LOCKNUT30 001636 2 BOLT31 32941C 2 LOCKNUT32 1461022 2 GAUGE WHEEL HEIGHT STRAP33 1460299 2 GAUGE WHEEL AXLE34 1456700 2 WHEEL COVER35 1460143 2 TIRE & RIM ASSEMBLY36 00002701 2 FLATWASHER37 32948C 2 LOCKNUT38 49036 2 COTTER PIN39 1438442 2 BUSHING40 1462335 1 BAFFLE, UPPER HOLD DOWN41 1462336 1 BAFFLE, LOWER HOLD DOWN42 311010H5C 2 BOLT43 6D9016 8 LOCKNUT, WHIZ44 02044900 2 BOLT45 1456253 2 CHAIN46 1461039 2 HOLD DOWN CHAIN PLATE47 00035900 5 BOLT48 1454958 2 SPACER, AUGER BEARING49 49208 2 HAIRPIN COTTER50 1460382 1 CHOPPER DRIVE SHIELD51 6D9007 7 FLANGE SCREW52 03101646 6 LOCKWASHER53 00002000 6 BOLT54 1460383 1 REVERSING WRENCH55 1452216 1 COVER, RIGHT DOOR SWITCH56 1452217 1 COVER, LEFT DOOR SWITCH57 1462368 1 SHIELD, LOWER ROLLER LEFT END58 1462366 1 SHIELD, RIGHT AUGER SAFETY59 00011700 1 LOCKWASHER60 00021800 1 NUT61 1460385 1 SHIELD, OVER-RUNNING CLUTCH62 49202 1 HAIRPIN COTTER

4407 & 4497 Baler (Sep-01)



4407 & 4497 Baler (Sep-01)




63 3263N4C 3 MACHINE SCREW64 329023C 3 LOCKNUT

4407 & 4497 Baler (Sep-01)


SILAGE MASTER RIGHT SIDE DRIVE COMPONENTS (OPTIONAL)

4407 & 4497 Baler (Sep-01)




1 1452594 1 JACKSHAFT2 1456426 1 SPUR GEAR3 00725073 1 KEY4 1456369 1 SPROCKET5 40652 1 KEY6 3922A29C 2 SETSCREW7 1454952 1 SPACER, BEARING8 1456024 1 BEARING9 3231009 1 WASHER10 00001300 5 LOCKWASHER11 02030700 1 BOLT12 1460343 1 BEARING SUPPORT BRACKET13 1460347 3 DRAWBOLT14 37056H5C 1 BOLT, CARRIAGE15 000516 3 BOLT, CARRIAGE16 00001200 10 NUT17 37051H5C 4 BOLT, CARRIAGE18 1456010 1 BEARING FLANGETTE19 1456016 1 BEARING20 1456009 1 BEARING FLANGETTE W/GREASE FITTING21 1456368 1 SPROCKET22 31104H5C 6 BOLT23 00011700 6 LOCKWASHER24 1456414 1 CUTCH, OVERRUNNING SPROCKET(INCLUDES ITEMS 51-58)25 1455817 1 REVERSING NUT26 40622.5 1 KEY27 1460285 1 IDLER ARM28 314017H5C 1 BOLT29 00002700 7 FLATWASHER30 1454928 1 BUSHING, IDLER PIVOT31 32905C 1 LOCKNUT32 1456362 1 SPROCKET, IDLER33 00750952 1 BOLT34 00001400 4 FLATWASHER35 1451685 1 TAB, SPRING HOOK36 32907C 1 LOCKNUT37 00059900 1 BOLT38 4528 4 LOCKNUT, HEX FLANGE WHIZ39 1451361 1 CHAIN IDLER ARM40 00003300 1 BOLT41 00002701 9 FLATWASHER42 1454895 1 BUSHING, IDLER ARM PIVOT43 1457435 1 TORSION SPRING44 32908C 2 LOCKNUT45 1436356 1 SPROCKET, IDLER46 02880900 1 BOLT47 1437523 1 FLATWASHER48 00753642 1 BOLT49 1438442 2 MACHINE BUSHING50 00034300 1 RETAINING RING51 1416665 1 HOUSING, RH52 1416666 1 HUB53 1416667 2 KEY54 1416668 2 LEAF SPRING55 1416669 1 THRUST RING56 1416670 1 RETAINER RING57 1416671 1 BUSHING58 8382 1 GREASE FITTING (PART OF ITEM 51)59 1456227 1 CHAIN60 6D5249 1 CONNECTOR LINK61 6D5250 1 OFFSET LINK62 32905C 4 LOCKNUT

4407 & 4497 Baler (Sep-01)



4407 & 4497 Baler (Sep-01)




63 1457441 1 SPRING, EXTENSION

4407 & 4497 Baler (Sep-01)


SILAGE MASTER CHOPPER (OPTIONAL)

4407 & 4497 Baler (Sep-01)


SILAGE MASTER CHOPPER (OPTIONAL)


1 1460319 1 CHOPPER FRAME2 1460318 1 SCRAPER3 00750959 5 BOLT4 00001300 17 LOCKWASHER5 1460321 1 CHOPPER WHEEL6 1461029 2 GRASS RING7 1461028 1 BLOCK, DRIVE BEARING8 02027400 7 BOLT9 00001200 2 NUT10 103767 1 WASHER11 1456024 1 BEARING12 1454952 1 SPACER, BEARING13 1456426 1 SPUR GEAR14 3231009 1 WASHER15 02030700 5 BOLT16 00725073 1 KEY17 1451681 1 ANGLE, FILLER SLOT18 37022H5C 11 BOLT, CARRIAGE19 00023500 13 FLATWASHER20 00011700 18 LOCKWASHER21 00021800 15 NUT22 1456014 1 BEARING FLANGE, TRIMMED23 1456016 1 BEARING24 1456013 1 BEARING FLANGE, TRIMMED W/FITTING25 1460345 1 KNIFE SUPPORT SHAFT26 1468350 14 KNIFE27 1458430 1 MACHINE BUSHING WASHER28 00755153 1 COTTER PIN29 1461233 2 AUGER SCRAPER30 10119000 4 BOLT31 1451691 1 PAN EXTENSION32 1460328 2 BELLCRANK PICKUP LIFT33 1461025 2 LINK, PICKUP LIFT34 02892100 4 BOLT35 32908C 6 LOCKNUT36 02959391 2 BOLT37 00002701 4 FLATWASHER38 1454934 2 SPACER, PIVOT39 1435502 2 PULLEY, CABLE40 00748823 2 BOLT41 32905C 2 LOCKNUT42 1451717 2 HOLDDOWN SPRING ANCHOR ANGLE43 00035900 9 BOLT44 6D9016 6 NUT FLANGE45 1457443 2 SPRING46 1451711 2 STRAP, HOLD DOWN SPRING HOOK47 1454939 2 BUSHING, HOLD DOWN48 1462364 1 SHIELD, SPUR GEAR49 45053 2 FITTING, 90DEGREES50 9D2010 2 LUBE BULKHEAD NUT51 9D2009 2 LUBE BULKHEAD CONNECTOR52 419112 1 CLEVIS PIN53 49205 1 HAIRPIN COTTER54 11108 2 ELBOW55 9907 1 PIPE NIPPLE56 99015 1 PIPE NIPPLE57 2438408 2 GREASE FITTING58 00011400 2 BOLT59 00011100 2 FLATWASHER60 00013901 2 HEX NUT61 03101646 2 LOCKWASHER

4407 & 4497 Baler (Sep-01)


KNIFE ENGAGEMENT ASSEMBLY (OPTIONAL)

4407 & 4497 Baler (Sep-01)


KNIFE ENGAGEMENT ASSEMBLY (OPTIONAL)


1 1460337 1 ENGAGEMENT ARM SUPPORT2 1460334 14 KNIFE ENGAGEMENT3 1454937 14 ROLLER4 1454938 14 ROLLER SPACER5 02957042 14 BOLT6 00011100 30 FLATWASHER7 000640 14 LOCKNUT8 1457441 28 SPRING9 1460338 2 KNIFE ENGAGEMENT SUPPORT10 1458430 1 MACHINE BUSHING WASHER11 00755153 1 COTTER PIN12 1460342 1 SHAFT, KNIFE13 1460346 1 ENGAGEMENT ARM POSITIONER14 00021900 1 BOLT15 00750940 1 LOCKNUT16 02030700 8 BOLT17 00001300 8 LOCKWASHER18 00001200 8 NUT19 37032H5C 2 BOLT, CARRIAGE20 03101646 2 LOCKWASHER31 00013901 2 NUT22 41938 1 CLEVIS PIN23 49202 1 HAIRPIN COTTER

4407 & 4497 Baler (Sep-01)


HYDRAULIC KNIFE ENGAGEMENT KIT #1450448 & HYDRAULIC CYLINDER #1457137 (OPTIONAL)


1 00007000 2 BOLT2 000640 2 LOCKNUT3 02960018 2 ELBOW4 1457137 1 HYDRAULIC CYLINDER5 1457138 1 ADAPTER, ORIFICED6 1457213 2 HYDRAULIC HOSE7 15007 2 PIPE BUSHING8 17003 2 PIPE CAP9 1451134 1 HOSE CLIP10 10121000 1 BOLT11 6D9016 1 WHIZ LOCK NUT12 1456797 1 SLEEVE13 5E805 3 TY RAP

HYDRAULIC HOSE ROUTINGHYDRAULIC KNIFE ENGAGEMENT

4407 & 4497 Baler (Sep-01)


HYDRAULIC KNIFE ENGAGEMENT KIT #1450448 & HYDRAULIC CYLINDER #1457137 (OPTIONAL)


1 00756059 1 DECAL, WARNING - OIL LEAK2 02975589 1 CYLINDER HEAD3 02975590 1 PISTON4 1417142 1 CYLINDER TUBE5 1417143 1 CYLINDER ROD6 5JRC8200 1 LOCKNUT7 02975532 Ref. SEAL KIT

HYDRAULIC CYLINDER #1457137

4407 & 4497 Baler (Sep-01)


SILAGE MASTER DRIVELINE 540 RPM WITH FRICTION DISC CLUTCH - (OPTIONAL) (P/N 1456404)


1 1416591 1 YOKE2 8388 2 CROSS BEARING KIT3 00756934 2 ROLL PIN4 8982 1 INBOARD YOKE5 2116431 1 INNER PROFILE6 1416606 1 OUTER PROFILE & SLEEVE W. A.7 1416595 1 INBOARD YOKE8 0921000460 1 FRICTION CLUTCH9 1416597 1 SHIELD CONE, 6 RIBBED10 1416608 1 OUTER SHIELD TUBE, OVAL11 1416609 1 INNER SHIELD TUBE, ROUND12 1416409 2 BEARING RING14 2738315 1 DECAL, IID SHIELD15 2738320 1 DECAL, IID SHIELD REMOVED16 1416438 2 SCREW17 1416600 1 SUPPORT BEARING18 1416601 2 GREASE FITTING19 1416613 1 SHIELD CONE, 6 RIBBED20 1416586 1 REPAIR KIT, SLIDE LOCK YOKE21 1416614 1 IID HALF ASSEMBLY W/SHIELD, TRACTOR END22 1416615 1 IID HALF ASSEMBLY W/SHIELD & CLUTCH, BALER END

4407 & 4497 Baler (Sep-01)


SILAGE MASTER FRICTION DISC CLUTCH 540 RPM (OPTIONAL) (P/N 0921000460)


1 8416 1 CLUTCH HOUSING2 0921000462 4 FRICTION DISK3 8375 1 HUB4 8376 1 DRIVE PLATE5 8377 1 DRIVE PLATE6 8465 1 THRUST PLATE7 8378 1 BELLEVILLE SPRING8 8425 4 HEX NUT9 1416620 1 BACK-UP SPRING10 1416423 3 BALL11 1416424 1 COMPRESSION SPRING12 1416425 1 LOCK COLLAR13 1416621 1 FLANGED RING14 1416622 1 SNAP RING15 0921000468 1 BELLEVILLE SPRING16 0921000470 1 Q. D. FLANGE KIT (INCLUDES ITEMS 9-14)

4407 & 4497 Baler (Sep-01)


SILAGE MASTER DRIVELINE 540 RPM WITH CUT-OUT CLUTCH - (OPTIONAL) (P/N 1456415)


1 8983 1 YOKE2 8388 2 CROSS BEARING KIT3 00756934 2 ROLL PIN4 8982 1 INBOARD YOKE5 2116431 1 INNER PROFILE6 1416606 1 OUTER PROFILE & SLEEVE W. A.7 8387 1 INBOARD YOKE8 1416677 1 CUT-OUT CLUTCH9 1416597 1 SHIELD CONE, 6 RIBBED10 1416608 1 OUTER SHIELD TUBE, OVAL11 1416609 1 INNER SHIELD TUBE, ROUND12 8393 2 BEARING RING14 00756005 1 DECAL, ROTATING DRIVELINE15 00756004 1 DECAL, SHIELD MISSING16 1416438 2 SCREW17 8974 1 SUPPORT BEARING18 1416601 2 GREASE FITTING19 1416613 1 SHIELD CONE, 6 RIBBED20 00767953 1 REPAIR KIT, SLIDE LOCK YOKE21 1416614 1 IID HALF ASSEMBLY W/SHIELD, TRACTOR END22 1416676 1 IID HALF ASSEMBLY W/SHIELD & CLUTCH, BALER END23 1416678 1 SHIELD, OUTER HALF-COMPLETE24 1416679 1 SHIELD, INNER HALF-COMPLETE

4407 & 4497 Baler (Sep-01)


SILAGE MASTER CUT-OUT CLUTCH 540 RPM (OPTIONAL) (P/N 1416677)


1 1416680 1 HOUSING RH2 1416681 1 HUB ASSEMBLY3 1416682 1 SPRING PACK4 1416683 1 WASHER5 1416684 1 RETAINING RING6 1416685 1 SEALING RING7 1416686 2 CAM8 1416620 1 BACK-UP RING9 1416424 1 SPRING10 1416425 1 LOCK COLLAR11 1416621 1 BACK-UP RING12 1416622 1 RETAINING RING13 1416423 3 BALL14 0921000470 1 Q.D. FLANGE KIT - INCLUDES ITEMS 8-13

4407 & 4497 Baler (Sep-01)


BULGE ROLLER & BELT CONVEYOR (OPTIONAL)

4407 & 4497 Baler (Sep-01)




1 1460376 1 BULGE ROLLER2 1462512 1 SHAFT, BULGE ROLLER3 40641.5 2 KEY4 3920A29C 6 SETSCREW5 1460375 1 ROLLER SCRAPER6 1461042 2 REAR SUPPORT, ANGLE7 1461040 1 RIGHT FRONT SUPPORT, ANGLE8 1461041 1 LEFT FRONT SUPPORT, ANGLE9 6D9001 8 SCREW11 00023500 10 FLATWASHER12 37032H5C 4 BOLT, CARRIAGE13 03101646 23 LOCKWASHER14 00013901 26 NUT15 1460371 1 RIGHT FRONT ROLLER SHIELD16 1460373 1 RIGHT REAR ROLLER SHIELD17 1460372 1 LEFT FRONT ROLLER SHIELD18 1460374 1 LEFT REAR ROLLER SHIELD19 3267F4C 4 SCREW20 1460379 2 REAR ROLLER SHIELD MOUNT21 1452067 1 RIGHT BALER SIZER22 1452068 1 LEFT BALE SIZER23 37031H5C 12 BOLT, CARRIAGE24 1456025 2 RIGHT BEARING FLANGE, TRIMMED25 1436011 2 BEARING26 1456026 2 LEFT BEARING FLANGE, TRIMMED27 000640 6 LOCKNUT28 1456370 1 SPROCKET29 40631.25 1 KEY30 3919A2C 3 SETSCREW31 6D5296 1 CHAIN32 6D5250 1 OFFSET LINK33 6D5249 1 CONNECTOR LINK34 1460370 1 SPROCKET35 3922A29C 2 SETSCREW36 1456105 1 BELT CONVEYOR37 1456107 1 PIN, BELT CONVEYOR38 1454929 1 IDLER ROLLER39 11D5009 2 BEARING40 1452593 1 SHAFT, IDLER ROLLER41 4064.625 1 KEY42 1461013 2 GRASS RING43 1461027 2 BLOCK, CONVEYOR BELT IDLER SLIDE44 1460327 2 TENSIONER ROD, CONVEYOR BELT45 00011400 15 BOLT46 00753642 2 BOLT47 1460332 1 DRIVE ROLLER48 6D5103A 4 BEARING FLANGE49 6D5113 2 BEARING50 37021H5C 4 BOLT, CARRIAGE51 00021800 10 NUT52 1456301 1 SHEAVE53 40621 1 KEY54 1456106 1 V-BELT55 2F031 2 IDLER PULLEY56 00749130 1 BOLT57 1461238 1 IDLER PULLEY ARM58 00002700 2 FLATWASHER59 32905C 6 LOCKNUT60 02788400 1 BOLT61 1457430 1 TORSION SPRING62 1454880 1 IDLER BUSHING, LS63 10121000 1 BOLT

4407 & 4497 Baler (Sep-01)



4407 & 4497 Baler (Sep-01)




64 1452210 1 SHIELD, RIGHT CONVEYOR BELT65 1452211 1 SHIELD, LEFT CONVEYOR BELT66 31104H5C 3 BOLT67 1451702 1 ANGLE, DRAWBOLT ANCHOR68 1460348 1 DRAWBOLT69 1452595 1 SHAFT, FRONT DRIVE70 1456010 1 BEARING FLANGETTE71 1456016 1 BEARING72 1456009 1 BEARING FLANGETTE W/GREASE FITTING73 37051H5C 4 BOLT, CARRIAGE74 1456373 1 SPROCKET75 1456412 1 U-JOINT (CONSISTS OF ITEMS 76-78)76 1416672 1 YOKE77 1416673 1 YOKE78 8486 1 CROSS BEARING KIT79 00725109 1 KEY80 710850 1 KEY81 1461046 1 IDLER MOUNT82 1462513 1 IDLER BAR83 00752228 1 SPIRAL PIN84 00011100 7 FLATWASHER85 02030700 3 BOLT86 6D9018 3 WHIZ LOCKNUT87 1457444 2 SPRING88 1456228 1 ROLLER CHAIN89 7D5118 1 CONNECTOR LINK

4407 & 4497 Baler (Sep-01)


ELEVATOR

4407 & 4497 Baler (Sep-01)


ELEVATOR

Item Part No. Qty DESCRIPTION

1 1456359 1 SPROCKET2 3922A29C2 ALLENHEAD CUP POINT NYLON LOCK SETSCREW3 40651.5 1 KEY4 1456016 2 RELUBE BEARING W/ LOCKING COLLAR5 1456009 1 RELUBE FLANGETTE W/ FITTING6 1456010 1 RELUBE FLANGETTE7 37051H5C4 CARRIAGE BOLT8 32905C 8 HEX LOCKNUT9 1455507 2 ELEVATOR DRIVE SPROCKET10 3920A29C4 ALLENHEAD CUP POINT NYLON LOCK SETSCREW11 1430261 2 BEARING12 1452556 1 ELEVATOR DRIVE SHAFT13 40652 3 KEY14 1430260 1 FRONT SHAFT COVER15 1432313 2 STRIPPER PLATE16 1451994 1 ANTI-WRAP SHIELD17 3267F6C 10 FLATHEAD SCREW18 0002350010 FLATWASHER19 0001170017 LOCKWASHER20 0002180017 HEX NUT21 1435512 2 CHAIN LIMITER22 007547644 BOLT23 007545774 LOCKWASHER24 1456015 1 FLANGE BEARING25 028869004 CARRIAGE BOLT26 000027004 FLATWASHER27 1452520 2 ELEVATOR CHAIN TENSIONER SCREW28 1457434 2 COMPRESSION SPRING29 15B1200 4 FLATWASHER30 000002004 HEX NUT31 32908C 2 HEX LOCKNUT32 1455506 2 ELEVATOR CHAIN SLIDING BRACKET33 007526584 BOLT34 000103004 LOCKWASHER35 1431445 2 CHAIN TENSIONER BRACKET36 420913 2 ROLL PIN37 1438440 4 WAVE SPRING WASHER38 1430220 2 CHAIN GUIDE39 1438442 2 MACHINE BUSHING40 1438426 4 MACHINE BUSHING41 1438446 2 MACHINE BUSHING42 1438200 4 RETAINING RING43 1436009 4 BEARING W/ LOCKING COLLAR44 1455508 2 ELEVATOR IDLER SPROCKET45 1436010 2 LOCKING COLLAR46 1432518 1 ELEVATOR IDLER SHAFT47 1431890 1 REAR SHAFT COVER48 370211C 7 CARRIAGE BOLT49 1434865 7 PIPE SPACER50 1432524 36 CHAIN CROSS BAR51 1438202 144 RETAINING RING52 1437503 216 WASHER53 1456222 2 ELEVATOR CHAIN W/ CONNECTOR LINK54 1416200 ref CONNECTOR LINK55 1416205 ref ONE BAR CHAIN SECTION56 1456027 72 BALL BEARING57 1428603 3ft REFLECTIVE TAPE

4407 & 4497 Baler (Sep-01)


LIMITED WARRANTY

1. LIMITED WARRANTIES1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal

purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)that the goods purchased are free from defects in material or workmanship.

1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to bedefective under normal use and service due to defects in material or workmanship.

1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, orlubricants, or which has served its normal life. This limited warranty does not apply to any part of any internalcombustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically foundin your Operator’s Manual.

1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of anynature on behalf of Manufacturer.

2. REMEDIES AND PROCEDURES.2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer

within 30 days of purchase.2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the

goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which theclaim is based.

2.03.Purchaser is responsible for returning the goods in question to the Dealer.2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and

service due to defects in material or workmanship, Manufacturer will:(a) Repair or replace the defective goods or part(s) or(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)

if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warrantyby Manufacturer.

The choice of remedy shall belong to Manufacturer.2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and

for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans-portation cost for the goods or part(s) from the Dealer to the designated factory.

3. LIMITATION OF LIABILITY.3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES

WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE.

3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FORUSE OF THE GOODS.

3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TOPURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGECAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOTLIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROMTHE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THEABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGESINCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.

3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDERTHIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HASOCCURRED.

4. MISCELLANEOUS.4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,

Texas.4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall

be deemed to be a waiver of any other term.4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the

invalidity of such provision shall not invalidate any other provisions herein.4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machineidentification when applying for warranty.

M&W Implement Model _____________________________________ Serial Number________________________________

Date Purchased __________________________________________ Dealer ______________________________________

ATTENTION:READ YOUR OPERATOR'S MANUAL M&W

An Alamo Group Company1020 South Sangamon Ave.

Gibson City, Illinois 60936217-784-4261

M&W

TO THE OWNER/OPERATOR/DEALERTo keep your implement running efficiently and safely, read your manual thoroughly and follow these directions andthe Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easilyfind the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safetyrequirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and3. Ensure that each employee uses such Seatbelt while the tractor is moving; and4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected

area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seatbelt if the tractor has a ROPS.2. Where possible, avoid operating the tractor near ditches, embankments, and holes.3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.4. Stay off slopes too steep for safe operation.5. Watch where you are going - especially at row ends, on roads, and around trees.6. Do not permit others to ride.7. Operate the tractor smoothly - no jerky turns, starts, or stops.8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machineryguards in place...

Please work, drive, play and live each day with care and concern foryour safety and that of your family and fellow citizens.

Printed U.S.A.Round Balers Rev 09-17-01 P/N 4904WP

revised 09-17-01 part no. 4904wp part's manual · to the owner/operator/dealer all implements...

Documents