Power RewinderInstructions

The power label and label liner rewinder in-cludes a 120 VAC (or 220 VAC for Europe) to12 VDC power supply. The rewinder has beendesigned to work with desktop bar code print-ers.

StepRewinder

Placement

Place the rewinder on a flat surface. The re-winder and printer both use separate externalpower supplies.

Do Not Apply Power to the Printer or Re-winder.

Verify that the power cords and supplies can beplaced and routed safely during use.

The printer, rewinder, and power suppliesshould never be operated in a location wherethey can get wet. Personal injury could result.

980079-002 Rev.C 1

WARNING

SW

M med

ia wid

th

I / 0

Step Remove the tape securing the rewind clip fromthe label rewinder tube. Slide the rewind clipoff and set it aside.

StepOrienting theRewinder and

Printer

Place the printer on the rewinders printer ped-estal. Push the printer up against the stop.

2 980079-002 Rev.C

SW

M med

ia wid

th

I / 0

RemoveShipping

Tape

RewindClip

Tape

SW

M med

ia wid

th

I / 0

Printer Orientation

PrinterStop

StepLoad the

Printer

Plug in the printer and apply power to theprinter only.

Load the printer with labels.

StepThread the

Liner (and Labels)

Feed the label media until two (2) or moreinches of label liner reach beyond the label re-winder tube.

Center the printer to align liner/label leader onthe center of the rewinder tubes ribs. For labelliners two (2) or more inches wide the rewindertubes ribs will be covered.

980079-002 Rev.C 3

SW

M med

ia wid

th

Slide

I / 0

Adjusting PrinterPosition To The

Label Stock

Ribs

StepLock the

Liner/Labels

Slide the rewind clip over the liner and on tothe label rewind tube. Fold the liner back to-wards the printer.

StepHand Wind

To Start

While pressing the printers label feed button,hand turn the label rewind tube. Turn the labelliner from the top to the front, until it has com-pleted one or more rotations.

4 980079-002 Rev.C

SW

M med

ia wid

th

I / 0

Securing The Liner

SW

M med

ia wid

th

I / 0

SW

M med

ia wid

th

I / 0

SW

M med

ia wid

th

I

Hand WindLabel Rewind Tube

StepSet Media

Selection Switch

Set the rewinders media selection switch tomatch the width of the roll.

StepApplying

RewinderPower

Turn the power switch off (O=Off). Plug in thepower supply and insert the rewinders powersupply connector into the rewinders power re-ceptacle.

Flip the power switch to the On position(I= On).

With power on, the rewinders motor designkeeps tension on the media liner while stoppedand even allows the operator to hand wind it inthe reverse direction.

980079-002 Rev.C 5

Media Switch Setting Media Width

N 1 to 2 inches

M 2 to 3 inches

W 3 to 4 inches

NOTE

NW

dia wi

dth

I / 0Startingthe Rewinder

NW

Mme

dia wi

dth

I / 0

PowerSwitch

StepRewinding

Labels

Press the printers feed button and re-adjust theprinter and label liner to wind the liner straight.

For labels 2" orwider:

The rewinder includes two (2) snap-on mediaguides to help the labels roll straight. Usage ofthese guides is optional, but recommended forrewinding labels wider than two (2) inches.

The media guides are not necessary forrewinding label liner (without labels) whileoperating the printer in the peel mode.

See Steps through for instructions.

6 980079-002 Rev.C

SW

M med

ia wid

th

I / 0

Re-AdjustingPrinter Position

To TheLabel Stock

NOTE

StepAdd Media Guides

Slide the media guides onto the rewind tube.The media guides will snap in for a snug fit.

StepAdjust

Media Guides

Slide the media guides gently into the labelliner.

980079-002 Rev.C 7

SW

M med

ia wid

th

I / 0

SW

M med

ia wid

th

I / 0

StepFine Tune LabelRoll Alignment

Press the printers feed button or start printinglabels. Slide the printer from side to side, as re-quired, to square the label liner on the tubeslabel roll. Slide the media guides into the labelliner to remove excess space and to squarethem to the tube and label roll.

StepRemoving The

Label Roll

Disconnect the power to stop label rewinding.Slide the rewind clip out of the rewind tube andlabel roll. Remove the media guides. Slide thelabel roll off the rewind tube.

8 980079-002 Rev.C

SW

M med

ia wid

th

I / 0

Power Rewinder Specifications

Maximum Media Width 4.125 in (105 mm)

Media Thickness 2 to 6 mils (after printing)

Rewound Media - Maximum Outer Diameter 5.00 in. (128.2 mm) on power roller

Rewinder Input Voltage 12 Volts Regulated Direct Current

Input Power Supply 120 VAC (or 220 VAC for Europe)