rinkal soni sip report1
TRANSCRIPT
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 1/81
A
PROJECT REPORT
ON
EMPLOYEE‟S HEALTH AND SAFETY MEASUREMENTS
FOR
MANHAR PROCESSOR
Submitted to
S.R.LUTHRA INSTITUTE OF MANAGEMENT
IN PARTIAL FULFILLMENT OF THE REQUIREMENT OF
THE AWARD FOR THE DEGREE OF
MASTER OF BUSINESS ADMINISTRATION
Under
Gujarat Technological University
UNDER THE GUIDANCE OF
FACULTY GUIDE COMPANY GUIDE
Ms Megha Gohel Mr. Mohan Panday
Assistant professorGeneral Manager
Submitted by
RINKAL SONI
Enrollment No: 118050592022
S.R.LUTHRA INSTITUTE OF MANAGEMENT
M.B.A PROGRAMME
Affiliated to Gujarat Technological University
Ahmadabad
July 2012
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 2/81
Co certificate
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 3/81
Institute’s Certificate
“Certified that this summer internship report Titled “EMPLOYEE‟S HEALTH
ANDSAFETY MEASUREMENT ” is the bonafide work of Ms Rinkal
Soni(Enrollment No.118050592022), who carried out the research under my
supervision. Ialso certify further, that to the best of my knowledge the work
reported herein does not form part of any other project report or dissertation on
the basis of which a degree or award was conferred on an earlier occasion on
this or any other candidate.
(SIGNATURE)
Megha Gohel
Assistant professor
Dr. J. M. KAPADIA
(In charge director)
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 4/81
PREFACE
In today's world, the Market all over the world is develop at much speed
so, the developing countries like India has great market to expand so, in India the
industries are having the very competitive scenario so the need for practicalstudies has become an important task. This report is prepared for the fulfillment
of the practical studies in the M.B.A. program.
Being the student of M.B.A. it is very necessary to have industrial training
to understand the real world application. Industrial training plays an important
role for the overall development of a student.
The main objective of the industrial training is to develop student's ability
Sense of market scenario and to understand the internal structure and various
aspects of an industry by these kinds of training students get opportunities to
show their skills and efficiency student can also get the if internal strength to
adapt to the industrial Environment.
In also creates awareness in the management student at grass root level
about the difficulties and challenges face by the organization in the currentbusiness world. This report also includes graphical trend analysis to represent
concept in most competitors are deal in large business in market so it is also our
effort to make report a comprehensive as possible.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 5/81
ACKNOWLEDGEMENT
The satisfaction and euphoria that accompany the successful completion of any
task would be incomplete without the mention of the leaders, whose constantguidance and encouragement crown all the efforts with success.
I am highly obliged to the GUJARAT TECHNOLOGICAL UNIVERSITY for
arranging the programme of practical training in masters in business
administration in such a manner.
I would like to extend my gratitude to all the staff and especially to Mr. Shyam
Jariwala of Manhar processor who provided me useful information and data
regarding the subject with their cent percent participation and supported in
making this project report a successful task. It was a memorable experience to
work with them and complete my summer training.
It is my privilege to express my deep sense of gratitude to Ms MEGHA GOHEL
and Mr JIMMY KAPADIA for their efforts, guidance, valuable comments and
suggestions for making this project report. She helped me to complete my report
on the practical study and give contribution to improve and expand my practical
knowledge.
Finally, I express my intense gratitude to my parents whose blessings has helped
me to translate me efforts into fruitful achievement.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 6/81
DECLARATION
I,RINKAL SONI, hereby declare that the report for“Summer Training Project”
entitled “Employee‟s Safety and Health Measurement” is a result of my own workand my indebtedness to other work publications, references, if any, have been
duly acknowledged.
Place: Surat
Date: RINKAL SONI
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 7/81
EXECUTIVE SUMMARY
The selected Topic was “EMPLOYEES SAFETY AND HEALTH MEASURES. It
is said that if the employees are secured in their organization they are
permanent. So every organization is giving higher priority to their employees
health and safety. If an employee is not secured in the job there are chances for
absenteeism, job turnover, and lower productivity. Thus looking to this aspect
MANHAR has given prime importance to the safety and health of their
employees. In this connection a survey was conducted on behalf of MANHAR
PROCESSOR to identify the satisfaction of employees in respect of safety and
health measures adopted by the company.
This project report is divided in two parts .In first part is of General information
part and it is related with Industry profile and company profile. Second part is
Primary study and it includes the objective of study and Research methodology &
analysis, conclusion. For gathering data about the Employees safety and health
measures, the structured questionnaire is use. And for data analysis SPSS
software is use and chi square test is apply on the data.
According to study in MANHAR PROCESSOR most of the employees aresatisfied with safety and health measures adopted by the company.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 8/81
Table of Content
SR.
NO.
PARTICULARS PAGE NO.
PART 1 GENERAL INFORMATION
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 9/81
1.
1.1
1.2
1.3
Industry profile
About the industry
World Market India
Growth of the Industry
2. About the Companies in Industry
3. Company profile
4. Product Profile
5. SWOT Analysis
6.
6.1
6.2
6.3
6.4
Functional Department
-Marketing
-Human resource
- Production
-Finance
PART-2 PRIMARY STUDY
7.
7.1
7.2
7.3
7.4
7.5
Introduction of the Study
Literature Review
Background of the Study
Problem Statement and Importance of the study
Objective of the Study
Hypothesis
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 10/81
Annexure
Bibliography
8.
8.6
8.7
8.8
8.8
8.9
8.10
Research Methodology
Research Design
Source of Data
Data Collection Method
Population
Sampling Method
Data Collection Instrument
9 Data Analysis and Interpretation
10 Results and Findings
11 Limitations of the Study
12 Conclusion/Suggestions
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 11/81
TEXTILE HISTORY IN INDIA
Indian textile enjoys a rich heritage and the origin of textiles inIndia traces back to
the Indus valley Civilization where peopleused homespun cotton for weaving
their clothes. Rig-Veda, the earliest ofthe Veda contains the literary information
about textiles and it refers toweaving. Ramayana and Mahabharata, the eminent
Indian epics depictthe existence of wide variety of fabrics in ancient India. These
epics referboth to rich and stylized garment worn by the aristocrats and
ordinarysimple clothes worn by the common people. The contemporary
Indiantextile not only reflects the splendid past but also cater to therequirements
of the modem times.Influences of changes shaping the industry:
We will touch upon some of the more significant changes thathave and are
shaping the Indian textile industry.
Implementation of New Equipment:
The textile industry has also become a high technology. Thetextile industry has
also become a high technology industry.No body earlier could have concerned
that the industry would require topof the line technical skills. Present day textile
machinery is fullycomputerized and needs totally new skills to effectively manage
it.
New Marketing Trend:
On the marketing side, there has been a total change, withalmost all players in
the industry extending their reach tointernational markets. The impact of these
trends on the textile industry isprofound. Increasingly any company cannot
sustain itself only on localmarket demand or only the exports. One has to look at
the global marketsin totality.
Competition:
This compulsion to access and compete in international marketshas been
perhaps one of the saving graces for the industry.Clearly the ability and necessity
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 12/81
of meeting global competition head on,has forced the industry to upgrade its
technology, product quality, coststructure and marketing skills. Truly, we have
learnt more from thecompetitions than from ourselves.
Technocrats:
Another shift in the industry is regarding entrepreneurship.Technocrats have
been able to become possible to have smallsize spinning, weaving and
processing mills. All this was earlier thedomain, solely
Cost Consciousness:
The greater competitive pressure have highlighted the need tocontrol cost of
every type of whether it be energy, water orlabour all of which were earlier taken
for granted now every mill is highlycost conscious and industrial engineers keep
detailed trace of every costparameter including energy consumption including
energy consumption,waste control, machine efficiency and productivity. No
doubt, this willhave to be an ongoing exercise. Since cost have to be ruthlessly
andpersistently brought down.
Labour intensive industry:
The textile industry being labour intensive, is slowly migratingfrom high cost
countries, such as the United states, Europe,Japan, Australia, Taiwan and
Korea. All these countries were at one timeleading textile manufacturers. But with
the high labour cost, capacities inthese countries are being diverted elsewhere.
This is happening even asthe developed economies make large investments in
better machinery andautomatism.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 13/81
Global Market
Sustainable Dyeing And Finishing
Textile World looks at some recent dyeing and finishing developments that are
economically and ecologically efficient and achieve high-quality results. Quality,
economic efficiency and, more and more, ecological methods are the
prerequisites for up-to-date production in the dye house. Color shade and depth
must be attainable, and there should be adequate levelness and accurate
fastness properties. Appropriate mechanical and chemical processing is
necessary to suit customer requirements as well as to create the required fabric
hand and surface characteristics.
Economical and ecological efficiency involves minimization of costs and
maximum profit as well as reproducible quality with minimal environmental
damage. Therefore, process optimization is a must to fulfill all parameters and
requirements for right-first-time production. Western wet-finishing costs are more
and more apparent in various Asian countries as well, and can be divided into the
following approximate cost proportions:
42-percent labour;
29-percent dyestuffs and chemicals;
6-percent water;
12-percent energy;
6-percent environment and safety measures; and
5-percent maintenance.
Technology
The technology for dyestuff manufacturing varies widely from relatively
simple (direct azo) to sophisticated (disperse and vat) dyes. Though
technology is locally available, most of it is outdated. The problem is further
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 14/81
compounded by the fact that the nature of the process changes from batch
to batch and, therefore, controlling the process parameters becomes difficult.
The Indian industry has made significant progress in terms of technology and
production.
The dyestuff industry is one of the heavily polluting industries and this has
resulted in the closure of units internationally and shifting of units to the emerging
economies. Most of the international manufacturers have transferred the
technology to developing nations like China, India, Indonesia, Korea, Taiwan and
Thailand.
This shift of manufacturing capacities is because the industry is perceived as a
high-cost and low return one. The batch processing also makes it a labour-
intensive industry. Thus, the competitiveness of developing economies
increases. However, the judiciary has come down with a heavy hand on several
manufacturing units, all over the country.
Disperse and Reactive dyes constitute the largest product segments in the
country constituting nearly 45% of dyestuff consumption. In future both this
segments will dominate the dyestuff market with Disperse dyes likely to have the
largest share followed by reactive dyes. These two segments will have the
largest share on account of dominance of textile and synthetic fibres in dyestuff
consumption. Vat segment is also expected to record positive growth in future.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 15/81
Growth of the industry
Dyeing & Printing Industry is growing with flying colours
The textile industry occupies a leading position in the hierarchy of the Indian
manufacturing industry. It has witnessed several new directions in the era of
liberalization. While textile exports are increasing and India has become the
largest exporter in world trade in cotton yarn and is an important player of
readymade garments, country‟s international textile trade constitutes a mere 3%
of the total world textile trade. Several mills have opted for modernization and
expansion and are going in for export-oriented units (EOUs) focused on
production of cotton yarn. It has passed through cyclical oscillations and at
present, it is witnessing a recovery after a downturn.
Of the entire industry volume of about 5 million tonnes, polyester and polyester
filament yarn account for about 1.7 million tonnes, and acrylic, nylon, and viscose
taken together for 300,000 tonnes. The balance is represented by cotton textiles.
A majority - some three fourths - of the textile mills are in the private sector. A few
of the units are in the co-operative sector with the public sector (Central and
State) accounting for about 15% of the total.
The textile industry is classified into (i) textile mills comprising composite and
spinning mills in the organized segment, (ii) small power loom and handloom
units in the decentralized segment, (iii) khadi-based units, (iv) manmade and
synthetic fibre and spinning units, v) knitting units, and (vi) made-ups (garments).
Besides, the industry has a large number of small units scattered all over the
country which are engaged in processing, dyeing and printing of yarn, fabrics
and for conversion. The processing units include sizing, desizing, kiering,
bleaching, mercerizing, dyeing, printing and finishing.
The country‟s per capita consumption of woven cotton fabrics is estimated at
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 16/81
around 16.5 meters. This has remained almost constant for quite some time with
the increased production absorbed by the expansion in population. Yarn is
produced by the mills in the organized segment but is consumed by power loom
and handloom segments as well. The production of cotton yarn is divided into
three categories, namely, coarse counts below 20s, medium counts between 20s
and 40s, and fine counts above 40s. The average count spun has increased from
about 25 in early 1960s to about 34 in 1990s. This indicates a change in product-
mix in favour of finer textiles and high value items.
The pattern of production of cloth in the textile industry is amazingly wide with
regard to types of fabrics produced with different mono and mixed materials.
In the conventional ring spinning system, increasing spindle speed beyond a level
was technologically difficult and economically non-feasible. The search for an
alternative method of yarn manufacture led to the development of three new
technologies, namely, rotor open-end, friction and air jet spinning. The spinning
limits of the four technologies are 6-12, up to 30, 6-18, and 20-80, respectively.
A major improvement in weaving efficiency has been brought about by
developments in spinning technology which has enabled production of yarn of
higher quality. A major share of the looms installed in composite mills is now of
automatic looms. However, auto looms installed in the decentralized and power
loom segments are small in number. Shuttle less technology, direct wrapping,
use of splicing technology, automatic doffing and knotting systems, help to
increase mill productivity. Speed of the auto looms or shuttle less looms is 60%
higher than that of non-auto looms.
The textile industry has managed to modernise the spinning sector but there is a
long way to go on the weaving front. India's power loom sector has over 10,000
shuttle less looms as compared to 150,000 in China. It may be recalled that India
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 17/81
today is the third largest producer of cotton, second largest producer of cotton
yarn and the largest exporter of cotton yarn in the world. The government has,
under its new textile policy set an ambitious export target of $50 billion to be
achieved by 2010.
The lead players in the Indian industry include Bombay Dyeing, Arvind Mills,
Century Textiles, Coats Viyella, Morarji Gokaldas Spinning, JCT, Hindustan
Spinning, etc.
While the Indian textile industry is a premier industry in India with a large
domestic market and sizable exports (considering India's export earnings), it is
still a small player in the global textile market. The global market is expanding
(estimated to grow from $ 309 billion to $ 856 billion by 2014). India has several
positive competitive strengths and can benefit from the global expansion.
However, India will have to catch up with modernization by restructuring and
upgrading its operations. It is an imperative and urgent need for the industry to
focus on value added products. With the end of the Multi-fibre Agreement at the
end of 2004, the potential is unlimited, if only the industry gets fully geared up to
adopt global standards.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 18/81
Major companies of Dyeing & Printing Industry
Krishna IndustriesSantel IndustriesJonson‟s Industries Ltd.Prakash Woven Pvt. Ltd.Dashmesh Jacquard &Power loom Pvt. Ltd.
Lakshmigraha Apparels Pvt. Ltd.Danube Fashions Ltd.Translabel IndiaKeshavlal & Mangubhai & Co.
Aqua Color Corp.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 19/81
Company Profile
INTRODUCTION
“MANHAR PROCESSOR” processors are incorporate in 1974. Concern started
at surat with 24 printing machines, 8 jet dying, 6 folding machine, 3 Stenter
machine, 2 loop machine, 2 drum machine, 3 zero-zero m/c, 2 boiler.
The concern is having large setup of latest plant and machineries to process
various type of manmade fabrics right from the beginning stage. This has been
possible because of a concern‟s large capital base, capital raised, reserves
preserved and loans from bank and finance institution.
HISTORY & DEVLOPMENT
In starting there was only one machine. Companies work is related on owner‟s
work. Company‟s expansion was carried on from 1994. 65 companies are
working jointly with this company. The printing work is done under the demand of
dyeing master.
The company produces various types of clothes like;
DANI
RUSSIAN
FRENCH etc.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 20/81
BACKGROUND
In Surat, it is fast emerging group in textile.
Good reputation in the market.
Processing good quality of cloth
Use sophisticated technique.
Well-equipped machineries.
COMPANY PROFILE
Name of the organization:
MANHAR PROCESSORS
Partners :
1. Rajeshbhai M Jariwala
2. Atulbhai M Jariwala
3. Pravinbhai J Jariwala
Features
High range production of cloth.
Skilful and talented worker.
Qualified manager.
Large plant location.
Well managed machinery.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 21/81
Quality production by using modern machineries.
SIZE OF UNIT AND FORM OF ORGANIZATION:-
According to the manufacture units may be classified as under
Small scale industry
Medium scale industry
Large scale industry
Out of all these industry Manhar processors is large scale industry.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 22/81
Organization structure
Managing Director
General Manager
Owner
Production
Manager
Finance
Manager
Personal
Manager
Marketing
Manager
Workers
Supervisors
Masters
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 23/81
SWOT ANALYSIS
SWOT analysis means over all evaluation of the company. The full norm of
SWOT is strength, weakness, opportunities and threats.
S – strength:-
The mgt. Of the company‟s is very good by management team. The
company has a very good professional staff.
The company is profit making company and continuous to have sound
financial position.
The capital base is strong.
They have chosen exact location for production.
They are totally family base company and not issues the share market. So
that there is no interface outside people in the company.
They have skillful staff in all departments.
They have good reputation in the market.
W – weaknesses:-
The company faces competition from established textile industries in the
city like manju mill, aishwarya mill etc. However, the company will withstand the competition with value addition in quality.
In company there are few technical and managerial worker, so the
company no very well attention in production
High investment in current asset.
They are not issuing any share in the market so they are not in the contact
of the market.
They do not contact any new customers directly.
O – opportunities:-
They have scope to export in the India‟s different cities.
They have scope to using spare capacity.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 24/81
A marketing opportunity is an area of buyer need in which a company can
perform profitability.
T – Threats:-
Meet competition from unorganized & small scale manufacturing
industries.
Presently the textile industries are passing from recession.
The competition has increased due to domestic market. The margins have
become thin in the industry. Improvement in quality is the only major
source of the profitability.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 25/81
FUNCTIONAL DEPARTMENT
MARKETING DEPARTMENT
Introduction:-
MARKET:-
The common use of market means a place where goods are bought or sold in its
strict meaning market need not necessarily mean a place of exchange.
How company is defining marketing?
Marketing is done under the satisfaction of the customer. The businessmen of
the market provide grey material to the company. Then the buyers make goods.
The printing design is done by the specially organised printing group. Then they
bring new innovation to the design. They maintain the quality control and
standard of the design. They also maintain upper credit policy.
Function of marketing department:-
Improve sales:- it refers increase the selling by the company and it is based on
the development design and implementation of marketing.
Customer satisfaction:-satisfaction is a person‟s feelings of pleasure or
disappointment that result from comparing a product‟s received performance to
their expectations.
Product differentiation:- it is a set of all products and items a particular seller
offers for sale.
Segment market: marketing involves satisfying customer needs and wants. In a
hypercompetitive economy with abundant choices.-
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 26/81
Segment , Targeting, Positioning:-
It is not necessary that all the customers will be gaining their satisfaction. If the
customer dissatisfied with the product then the company should provide them
satisfaction.
If the price is very high then the customer will be not satisfied. In case if the price
is satisfied by the customer but the design is not liked by the customer. So, if this
situation is carried out then the different segment is carried out.
For eg:- like the cloth of dani and Russian is very cheap able cloth so its price is
cheap. But the cloth like turkey is very expensive and the charge of printing is
also very high.
In this process the customer is attracted by the quality of cloth. In this way the
company target the customer.
The companies which work together with “MANHAR PROCESS” are competitive
in nature and whosoever cloth is good that company‟s position is high, this act is
carried out in positioning
.
CRM and customer support activities:-
In this company gives satisfaction to the customer.
They also provide best goods and services.
In Manhar process the job is done on credit base.
Product mix:-
Sari
Length: - 5.25 meters
Width: - 45 inch
Dress material
Length: - 4 meters
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 27/81
Width: - 45 inch
HUMAN RESOURCE DEPARTMENT
INTRODUCTION:-
MANHAR PRCESSOR has a separate personnel department. All the activities
related to the personnel department are performed by Mr. Ajit Mehta; the co-
owner of the mill. The function of this department is to take decisions related to
employees.
Human resource management may be defined as that field of management
which has to do with planning, organizing and controlling the functions of
procuring, developing, maintaining and utilizing a labour force.
Objectives of human resource management
Objectives of human resource management are derived from the basic objectives
of an organization.
1. To help the organization attain its goals by providing well-trained and wellmotivated employees.
2. To employ the skills and knowledge of employees efficiently and effectively.
3. to establish and maintain productive, self-respecting and internally satisfying
working relationships among all the members of the organizations.
4. To bring about maximum individual development of members of the
organization by providing opportunities for training and advancement.
5. To secure the integration of all the individuals and groups with the organization
by reconciling individual with those of an organization.
6. To help maintain ethical-policies and behaviour inside and outside the
organization.
7. To manage change to the mutual advantage of individuals, groups, the
organization and the society.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 28/81
Organizational structure:-
NO.OF WORKERS:-
In “MANHAR PROCESSOR “there are 300 employees working with the firm.
They have also 3 dyeing masters,3 printing masters,6 supervisions. They both
qualitative and quantitative workers.
Owner
General Manager
Personnel manager
(personnel&administer)
Masters
Clerk
Peon
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 29/81
PRODUCTION DEPARTMENT
INTRODUCTION:-
“production is the process of converting the raw materials and/or the other
inputs into the products for further production or finish goods or service so that
the utility of the inputs is created or enhance (by change in physical form or
mechanical property)and the needs of consumer are satisfied.”
Product and their established capacity:-
Product:
Their product is to dye and print saris and prepared them finally to send them in
TEXTILE MARKETS for their trading.
INPUTS
Manhar processors having raw material as a grey, chemicals& colors.the parties
purchase the grey cloth from surat textile market, new textile market,mahavir
market etc.after completing job work it will be delivered to concerned customers
in the given period.
their main raw material are:-
Grey cloth comes from different parties.Different chemicals like pb verga, bb,
silicon b, hydrocaustic soda etc.used in process.Colours used for dying and
printing.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 30/81
Process
Finished product:-
In this stage the product is finally prepared. So the product is ready for disputing
to customers. This final product is delivered in the textile markets in the city
through trucks, tempos and other transporters.
Drum
machine
Jet dying
Stenter
machine
Zero
zeromachine
Loop
machine
Washing
Printing
machine
Stenter
machine
Folding
machine
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 31/81
FINANCE DEPARTMENT
INTRODUCTION
MEANING OF FINANCE:
The importance of finance in the business is same as the importance of the
spring in the clock. Finance is required from the starting until it terminates, as a
means of the business transaction. Finance is the blood of the business without
which an enterprise cannot survive.
“ finance is that administrative area or set of administration function in an
organization which relates the arrangement of cash and credit so that
organization may have the means to carry out its objective as satisfactory as
possible”.
SOURCES OF FINANCE
Following sources of finance are used by” MANHAR PROCESSOR”s for their
short term requirement of fund:
1. Bank loan
2. Cash credit
“MANHAR PROCESSOR” processors have no requirement to take loans frombanks and financial institutions because of their well profitability management.
But they take cash credit from financial institutions when they have to establish
new plant or to make expansion.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 32/81
INTRODUCTION OF STUDY
LITERATUREREVIEW
Numerous research studies have been conducted on Occupational Health andSafety (OHS) aspects in Textile and other industries such as Chemical, Mining,andAgriculture etc. in various parts of the world. In this chapter, under the varioussections,different studies are reviewed which were conducted on Occupationalhealth and safetyall over the world with respect to our research objectives. Thevarious sections such asthe factors effecting OHS, the work place hazards,causes of industrial accidents, existingmedical protection and facilities and lifestyle, behaviour and attitude of the workers aswell as management. We reviewedthe different studies conducted on OHS all over theworld. The current review is
an attempt to give a comprehensive draft of the findings ofthe research studiesperformed in different parts of the world with respect of our researchobjectives inorder to provide information about possibilities of improving occupationalhealthand safety situation in textile industry and recognize its significance.2.1 FACTORS EFFECTING OCCUPATIONAL HEALTH ANDSAFETY IN TEXTILE INDUSTRY:The various factors such as education, age, physical health socioeconomicconditions, role of management compensation plans, occupationalhealth and safetymanagement and admin standards, labourbehaviour wereresponsible to create awarenessand knowledge about occupational health andsafety. These factors were identified in thedifferent parts of the world which wediscuss as below.
Argyris,C. (1964).discovered association among work accident, stress level andeducational background of textile workers. The study was carried out in twodifferentparts. In the first part of questionnaire, for the Turkish population, theGlazer Stresscontrol Life-Style scale was used. The results indicated thataccidents on workplace aredirectly linked with the worker‟s stress level andeducational background. The stresslevel also linked with sex and nationaldifferences of textile workers. In the Turkish malegroup population, less educatedtextile workers had lower stress than more educatedtextile workers. The resultshowed that Turkish workers had lower educational level thanEnglish workers.Furthermore, less educated workers had low stress level and lessaccidentsduring their work. Therefore, the workers who have a tendency to hadaccidentsalso showed the lower level of education and less stress It wasconcluded that pooreducation is the prime reason of work accidents. So toreduce the accident rate;educational level of workers must be high.
Bowen. E., & Ostroff, C. (2004).described that the mean age of labour force inmany Europeanwas increasing; with the result problems were caused by ageing
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 33/81
of workforce. Activitiesto maintain workers‟ ability to work have become a priorityin OH&S. Work ability maybe considered to include physical health, psychosocialwell-being and professionalcompetence of individuals, but also an appropriatework environment and workorganizations which improve the performance of theindividuals at work.
Taylor et al (1970) conducted a research on the physical health of workers.Hisresearch based on the chronic disability, to discover about the records of disable people working in industry, excluding for those who were registered withthe Department ofEmployment and Productivity. A combined survey conductedby six factory doctorsconsisting of 11,399 men of aged 16- 64 from sevencompanies is illustrated. In which10.8 per cent of the population (1233 men) wererecognized as having chronic medicalimpairments, which could affect workingcapability. The frequency increased from 3%under the age of 25years to 28% per cent over the age of 60. The only 1/3 of these menwas formally registered andthey were not true representative of the entire disabled eitherin terms of severity
or of diagnosis. The most occurring reason of disablement wereChronicbronchitis and asthma, disorders of the backbone, coronary heart diseaseandsevere visual loss.
Claire (1987) High injury rates tend to occur in lower socio- economicgroupswhose perception of causation and work experience place them at oddswith management. At the same time injuries are treated, investigated andcompensated at an individualFurther, patterns of behaviour, injuries and overtconflict may be related to the levels ofcontrol experienced at work A case studyresults demonstrated that a conflict of interestwas recognized by both workersand management and resulted in tacit acceptance of „restrictivelabour practices',as survival mechanisms. This recognition of inherent danger, 9injury-avoidancewithdrawal and the contradictory nature of control for safety andproduction, byboth sides, is de facto legitimating of occupational injuries beingembedded in thesocial relations of production - rather than being 'accidental'.
Harter, J. K., Schmidt, F. L., & Hayes, T. L.(2002).discovered that the Pan American Health Organization (PAHO)introduced a new Tool Kit with thecollaboration of CERSSO which was obtainable inMay 2002. The purpose of thistool kit was enabling managers and line workers ingarment factories to self-diagnose plant and workstation hazards. Furthermore it providedthe way toestimate the costs and benefits of spending in occupational health andsafety(OHS) for the improvement of production and competitiveness. Theinstrument wascomprehensively developed in such way that any user may collectthe data easily. Itincorporated clinical, epidemiological, engineering, riskassessment, and liability issues. The data shows that since July 2002, approx.2400 officials and employees of 736garment industrial units; Ministries of Labour Health, Social Security organizations, andTechnical Training Institutions of Central America and the Dominican Republic had usedthis tool. Employers werenow conscious of the economic benefits to invest in OHS.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 34/81
Moazzam (2000) described about the injury benefits are paid to secure aworkerwho was unable to attend his duty due to employment injury at the rate of 100% of hiswages to a maximum of 180 days. Disablement gratuity is paid to asecured worker whohas received an employment injury and his degree of
disablement has been assessed up to20%.
Peterson,S. J., & Luthans, F. (2006).explained in the environmental health andsafety management andauditing programs that numerous standards andregulations serve as a basis for bothoccupational health and safety programmersand for auditing programme. For instance, Occupational Safety and Health
Administration (OSHA) is one source of US workplace, standards. Other countries had standards and regulations similar to OSHA‟s standards. Manycompanies had their own internal health and safety standards that extendbeyond government standards and guidelines.
Schneider, B., Hanges, P. J., Smith, D. B.,& Salvaggio, A. N. (2003).explainedin his research paper on the challenging world of work andimplications for labour inspectors. The social and political expectation at work haschanged significantly.The workers are now less tolerant with respect to their workingconditions whichhave directed to an increase in the statistics of complaint and an enormouspressure on the labour inspectorates which in turn has led to moreinvestigationsat the workplace and for more punishment of individuals andenterprises which do notComply with the rules and regulations. There are different factors, which directlyor indirectly create effect on OHS. Worker (labour) education, age, income,awareness, knowledge, personal or physical health, injury and disease benefits,environment health and safety management system and affective audit andinspection system. These factors were studied in Turkey, India and UnitedStates, which were closely affecting the OHS in Pakistan textile industry.
2.2 WORKPLACE HAZARDS IN TEXTILE INDUSTRY:
There are different hazards which faced by the workers in textile industry. Thesehazards are explained as;2.2.1 Biological Hazards (Cotton Dust):
Schneider,B., & Schmitt, N. (1986).described the word Byssinosis is derivedfrom the Greek word“Bussus” meaning fine Linen or fie flax. Byssinosis is arespiratory disease of workers of cotton, flax, soft hemp and is classicallycharacterized as shortness of breath; cough and tightness of chest on Monday or the first day of return to work after a time off. Huter(1978) explained thatbyssinosis is also known as strippers asthma, grinders asthma or Card roomasthma.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 35/81
Croften (1981) explained that in 1831 Dr. JP Kay a physician in Manchester, firstdrew attention to this disease by suggesting that cotton workers suffered from arespiratory disease, probably as a result of exposure to dust at workelsementioned byGren how in a report to the Privy Counsel, London. In 1963
Jesse Leach, a factory surgeon described the disease in detail and found it in themills of Heywood. Oliver in1908 suggested that the manufacturing of cotton wasnot a healthy occupation. In 1955Werner reported that in early stages thedisease is characterized by tightness of chest. Before this it was supposed thatthe disease was recognized to the collective effect of dustand generalatmospheric pollution.
Emery, R. E., & Trist, E. L. (1960) explained that a great number of textileworkers managing Cotton and flax suffer from various respiratory symptoms andshow a failure in lung function.
Schechteret al
. (1986) discovered in different epidemiological studies, it hadbeen shown that cotton textile workers had an increased occurrence of bothdisruptive11and restraining lung function. West Pakistan Employees(Occupational Disease) Regulation (1967) in Pakistan
Ryan,A. M., Schmitt, M. J., & Johnson, R. (1996).respectively. Since then not asingle textile worker has been declared as sufferingfrom byssinosis and receivedany disablement pension (Social Security Institution Annual Report, 1997).
2.2.2 Physical Hazards:
The noise is a cause, which created hazard in the work place. Noise exposure atwork can cause critical hearing damage. It is one of the most occurring healthproblemswhich can be difficult to identify because the effects build up slowly withtime.According to the textile statistics of United Kingdom, industrial hearing lossis theoccupational disease with the largest number of civil claims accounting for about 75% ofall occupational disease claims.
Zohar,D., & Luria, G. (2005).conducted an observational cross-sectional studybased on asample of 100 women workers. These workers were volunteered,outlined their cardiorespiratoryand musculo-skeletal profile before, during and atend of work. Furthermore, the information on their health status was collected inadvance. It was surprisinglydifferent to expectations; there was no significantchange in respiratory function. Anyhow, the musculo-skeletal problems werefound to be richly present with pain in 91%of the women workers. In the regionwise mapping of pain showed that postural pain inlow back was present in 47%while in neck was 19%. There was no gap since the wheelcontinued to spin thethread continuously, unless a worker wanted to stop the work. Inthis study it wasconcluded that pain and tiredness were the main problems for women inthe
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 36/81
spinning section of the small-scale industry. Women had to take up doubleliability ofa full-time job as well as the family work. It was measured thatergonomic factors such asprovision of a backrest and regular rest periods couldremediation the musculo-skeletal symptoms.
Wright, P. M., Gardner, T. M., Moynihan, L.M., & Allen, M. R.(2005).investigated the risk of mortality in a group of textileworkersand observewhether specific occupational exposure was connected with mortality.Theseworkers may be affected to textile dusts, a broad series of chemicals andelectromagneticradiation.The statistics of present and previous members of atextile industry union weretake out from membership cards and coordinated withthe National Death Index forobtaining date and reason of death. The 113 deathswere occurred in the cohort of 7684textile workers. The both male and femaletextile workers had same risk of death for many reason, cancer or cardiovascular disease to the general population. As compared towomen, male workers hadgreater risk of death from injury. There were no significantdata which reveals
considerable increase in risk with particular occupational exposures.
Schneider,B., & Schmitt, N. (1986).proposed a technique that could be used bythe workers andmanagement themselves to overcome exposures to noise asmuch as possible in the firststage. In later stages, when required, increasinglycall in the assistance of professionalsand experts to recognize more complexsolutions and arrange individual protection andmedical supervision. Thisapproach comprises of three stages. Stage # 1 is observation;simple and easy touse by the workers to identify the problems, recognize clear-cutsolutions, and callfor support when desired. Stage# 2 is analysis, which is complex butmore costly.It is performed with the help of occupational health professionals to classifymorescientific control measures and to set up a programme to protect hearing.Stage#3 isexpertise, performed with the help of audio experts for specialmeasurements and controlmeasures. The recommended approach enhances themeasurement procedure that wasusually suggested, by providing for onebeginning stage used by the people directlyconcerned. It clearly recognizes (a)the capability of the workers and management abouttheir working conditions and(b) that information and dimensions of acoustics are not acomplete prerequisitefor solving at least partially noise problems. It attempts tocategorize in series andoptimize the collaboration among the workers, the occupationalhealth specialists,and the acoustics experts.There are different factors, which are responsible tocreate the hazards in theworking environment. In textile these are Physical,Biological, Chemical and Ergonomic (personal factors). There are some other aspects, which are responsible to create hazardsin the work place environmenti.e. shift work, smoking at work place, job strained. In theIt was concluded in thelight of the research that intensity of hazards in textile industrywere more in under developed country like Pakistan and Bangladesh in relation to biological,physical, chemical and ergonomic factors are compared to develop countrieslike United Kingdom and Australia.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 37/81
2.3 MEDICAL PROTECTION IN INDUSTRIAL ESTATES:
Harter, J. K., Schmidt, F. L., & Hayes, T. L.(2002).conducted a research, which
comprised of the credentials onmorbidity profile of the workers working ingarment factory. The research was carriedout in 2003-2004 at eight garmentfactories, employing more than 4000 workers. Databased on the yearly medicalcheck up of the workers of this industry. The records of theannual medical checkup for 3,858 workers were examined. The labour force consisted largely of women in the 21-30 years age group, whereas males being more inthesupervisory and mechanical cadres. Nobody had undergone a periodicmedical examination. Musculoskeletal problems were the most common preexisting morbidity stated by workers and the same problem was reported by mostas being a commonoccupational problem. At both ends of the spectrum,malnutrition was also discovered through body mass index, (BMI). Hypertension
was found in almost 2.5% of theemployees. In the study, an annual medicalcheck up provided to the workers was likely to yield a large number and variety of morbidity as observed. It was also revealed that theCoordination of the management of the factory is critical to the success of such alarge-scale important programme.
Gross,E., & Etzioni, A. (1985).explained sickness day and the n thecomparative social policy literature, the Australian welfare state had, with only afew exceptions, been characterized as lagging far behind most other advancednations. After providing a survey of the main themes of that literature, the paper used the example of paid compensation for periods of absence from employmentdue to sickness to illustrate the complexities of characterizing Australian socialpolicy development in comparative perspective. Whilst Australia was shown tohad been a latecomer in providing social insurance and sickness and asremaining an exceptionally low spender on social insurance sickness benefits, itis also shown to had developed a very different, and, until quite recently, notnecessarily inferior, social policy strategy for catering to the sickness needs of itspopulation.
2.5 EFFECT OF LIFESTYLE AND BEHAVIOUR (WORKERSAND MANAGEMENT):
Behavioural Based Safety is an approach to safety that focuses on behaviour of the workers which is the main reason of most work related illnesses and injuriesThis isdangerous, as it shifts the focus from identifying the hazards in workplacesand then eliminating or reducing the risks associated with them - which is whatemployers have the legal duty to do.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 38/81
Wright, P. M., Gardner, T. M., Moynihan, L.M., & Allen, M. R. (2005).Foundedthat in modern textile industry the worker will be responsible for forty to sixtyautomatic looms at a time, which increased the risk. It is now likely that theexposure had increased manifold with the changing life style. Smoking hasconsiderably increased and byssinosis higher in smokers than non-smokers.
Ryan,A. M., Schmitt, M. J., & Johnson, R. (1996). Conducted his research onthe management and motivationalCauses in the control of noise induced hearing loss (NIHL). In this study, theresearcher linked these factors to the standards of hearing conservation, attainedin industry as demonstrated by compliance with the Noise at Work Regulations.The research consisted of a survey of 48 organizations across Britain, and amore complete examination, ten of these as case studies. A useful hearingprotection programme requires three management characteristics: a) leadershipfrom senior management, b) the ability of middle management (mainly inproduction and engineering) to put hearing preservation measures into practice,
and c) expert technical knowledge of noise and about the legislation. The studyconcludes to the need for further education and motivation of senior managers asthe main concern in improving standards of hearing conservation and noisecontrol.
Ostroff,C. (1992).discussed that the employee silence behaviour is amajorimpediment in organizations attempt to leverage on the stock of knowledgein its diverse workforce. In order to contribute to the understanding of thisconcept, Dmitri‟sand Akola tested a silence behaviour model in which silenceclimate wefound to affect the enactment of employee‟s silence behaviour. Themodel tested in this study improved on this by accounting for the moderating roleof self-esteem and locus of control and also indicating silence behaviour as bothantecedent and outcome of work attitudes. Results obtained were justifying therecommended expansion. Recommendations were to alwaysaccount for individual differences in silence behaviour model and apply system managementin the application of the model.
Harter, J. K., Schmidt, F. L., & Hayes, T. L.(2002).above the past 20 years thelabour markets of industrialized countries had gone through a series of significantchanges. These changes had been connected with important changes in workprocesses but until now no such attention was paid to the consequences of thisfor occupational health and safety (OHS). This article review is an available proof on the impact of particular labour market and work planning on the frequency of occupational disease and injury, the reporting and treatment of OHSproblemsand regulatory systems. The evidence is incomplete and far more research isrequired.Berenice (1998) discussed the psychological factors attributed to theoccupationalhazards. Psychological stress may be attributable to migration fromrural to urban areas, unfamiliar working, conditions, and long distances betweenpeoples, work places and homes, poor transport, poor housing or low incomes.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 39/81
The numbers of persons dependent on a work may also be significant in thisconnection. A study in Thailand showed that52% of the women working in atextile factory had full responsibility for a family of four or more. Psychosocialfactors also have a bearing on the incidence of alcoholism drug abuse andaccidents. The influence of hazards encountered in the work place is often
compounded by outside circumstances. For instance, mal nutrition, diseaseprevalence and poor housing may be additional burdens that workers have tobear. Moreover, hazards may be transferred from the workplace to the home.
Tuomi et al (1998) and Eskelinen et al (1991) described the work abilityindex(WAI), based on a person‟s own view of his or her work ability, diseasesdiagnosed by medical doctor, and sick leave throughout the past year, has beenfound to estimate early retirement and future disability. Ergonomics factors werealso known as human factors and they are related with those causes that caninfluence people and their behaviour, in a work environment. Human factors weredescribed as the organizational, environmental and job factors, and human and
individual characteristics which influence behaviour at work. Carefulconsideration ofhuman factors can improve health and safety by minimizing thenumber of accidents and cases of ill-health at work place. It also givesconsiderable profits for business by reducing the costs linked with such incidentsand increasing efficiency.
\
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 40/81
Objectives of the study
1.To examine & analyse various health & safety activities conducted in
organisation.
2.To determine how this activities are implemented & managed in a successfulmanners by different departments.
3.To determine whether the actual beneficiaries are happy & satisfied with the
activities conducted.
4.To conclude how these activity are benefiting employees & keeping them
motivated & creating a healthy work environment.
5.To suggest measures if any on the basis of findings during the course of study.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 41/81
Hypothesis:
TEST No. 1
Null Hypothesis (HO): There is no significant difference between accident
sometime not reported and health and safety programme offered by organization.
Alternative Hypothesis (H1): There is significant difference between accident
sometime not reported and health and safety programme offered by organization.
TEST No. 2
Null Hypothesis (HO): There is no significant difference between employees
concern about health and safety and their priority to health and safety while they
performing the job.
Alternative Hypothesis (H1): There is significant difference between employees
concern about health and safety and their priority to health and safety while they
performing the job.
TEST No. 3
Null Hypothesis (HO): There is no significant difference between health and
safety inspection of work conducted at regular interval and health and safetytraining programme offered by organization,
Alternative Hypothesis (H1): There is significant difference between health and
safety inspection of work conducted at regular interval and health and safety
training programme offered by organization.
TEST No. 4
Null Hypothesis (HO): There is no significant difference between health and
safety inspection of work conducted at regular interval and health and safety
training programme offered by organization,
Alternative Hypothesis (H1): There is significant difference between health and
safety inspection of work conducted at regular interval and health and safety
training programme offered by organization.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 42/81
RESEARCH METHODOLOGY
5.1 RESEARCH DESIGN
Descriptive or statistical research
The research design use here is DESCRIPTIVE research design. Descriptive
research does not fit neatly into the definition of either quantitative or qualitative
research methodologies, but instead it can utilize elements of both, often within
the same study. The term descriptive research refers to the type of research
question, design, and data analysis that will be applied to a given topic.
Descriptive statistics tell what is, while inferential statistics try to determine causeand effect.
In this project we have undertaken the descriptive research design.
5.2 SOURCE/S OF DATA
TYPES OF DATA
PRIMARY DATA:
Data that has been collected from first-hand-experience is known as
primary data. Primary data has not been published yet and is more reliable,
authentic and objective. Primary data has not been changed or altered by human
beings; therefore its validity is greater than secondary data.
Importance of Primary Data:
Validity
Authenticity
Reliability
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 43/81
Sources of Primary Data:
Sources for primary data are limited and at times it becomes difficult to
obtain data from primary source because of either scarcity of population or lack
of cooperation. Regardless of any difficulty one can face in collecting primary
data; it is the most authentic and reliable data source. Following are some of the
sources of primary data.
1. Experiments
2. Survey: Survey is most commonly used method in social sciences, management,
marketing and psychology to some extent. Surveys can be conducted in different
methods.
a. Questionnaire
b. Interview
c. Observations
No primary data or analytical tools are included in this study. The entire
used in the project are secondary data.
Only questionnaire analysis will be done using primary data.
Questionnaire relating to hedging, risk management and future strategies is
being prepared.
SECONDARY DATA:
Data collected from a source that has already been published in any form
is called as secondary data. The review of literature in nay research is based on
secondary data. Mostly from books, journals and periodicals.
Importance of Secondary Data:
Secondary data can be less valid but its importance is still there.
Sometimes it is difficult to obtain primary data; in these cases getting information
from secondary sources is easier and possible. Sometimes primary data does
not exist in such situation one has to confine the research on secondary data.
Sometimes primary data is present but the respondents are not willing to reveal it
in such case too secondary data can suffice: for example, if the research is on
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 44/81
the psychology of transsexuals first it is difficult to find out transsexuals and
second they may not be willing to give information you want for your research, so
you can collect data from books or other published sources.
Sources of Secondary Data:
1. Published Printed Sources: There are varieties of published printed sources.
Their credibility depends on many factors. For example,
a. Books
b. Journals/periodicals
c. Magazines/Newspapers
2. Published Electronic Sources: As internet is becoming more advance, fast and
reachable to the masses; it has been seen that much information that is not
available in printed form is available on internet
a. E-journals
b. General websites
c. Weblogs
3. Unpublished Personal Records: Some unpublished data may also be useful in
some cases.
a. Diaries
b. Letters
4. Government Records: Government records are very important for marketing,
management, humanities and social science research.
a. Census Data/population statistics:
b. Health records
c. Educational institutes records
5. Public Sector Records:
a. NGO's survey data
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 45/81
b. Other private companies records
Sources of secondary data are selected for collecting the required data for
this project which is often readily available. Secondary data can be less valid but
its importance is still there.
5.3 DATA COLLECTION METHOD
PRIMARY DATA:
No primary data or analytical tools are included in this study. The entire used in
the project are secondary data.
Only questionnaire analysis will be done using primary data. Questionnaire
relating to hedging, risk management and future strategies is being prepared.
SECONDARY DATA:
Sources of secondary data are selected for collecting the required data for this
project which is often readily available:
Internet
Newspaper
Referred respective firms broachers
Articles
5.4 POPULATION
A research population is generally a large collection of individuals or
objects that is the main focus of a scientific query. It is for the benefit of the
population that researches are done. However, due to the large sizes of
populations, researchers often cannot test every individual in the population
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 46/81
because it is too expensive and time-consuming. This is the reason why
researchers rely on sampling techniques.
A research population is also known as a well-defined collection of
individuals or objects known to have similar characteristics. All individuals or
objects within a certain population usually have a common, binding characteristic
or trait.
Usually, the description of the population and the common binding
characteristic of its members are the same. "Government officials" is a well-
defined group of individuals which can be considered as a population and all the
members of this population are indeed officials of the government.
5.5 SAMPLING DESIGN
“A sample design is a definite plan for obtaining a sample from a given
population. It refers to the technique or the procedure the researcher would adopt
in selecting item for the sample “Generally Sample designs are two types
NON PROBABILITY SAMPLE DESIGN
In the research Non-probability research design is used.
SAMPLING AREA
Sampling area may be a geographical one, such as state, district, village
etc. The researcher will have to decide one or more of such area that he has to
select for his study.
In this research study Surat as a sampling area.
SAMPLING UNIT
Sampling unit may be defined as an individual, pair or group of persons
included as respondent.
In this research study General health and safety measures of the employee are
the sampling units
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 47/81
SIZE OF SAMPLE
“This refers to the number of items to be selected from the universe to
constitute a sample”
In the present research sample size is 75.
5.6 SAMPLING FRAME
Sampling frame can be defined as the list consisting of the units of the
population. One very necessary and critical point to be kept in mind in case of the
sampling frame is that it should be made up to date and also it should be free
from the various errors of the omission and duplication of the sampling units. In
many cases, it has been observed that the preparation of the sampling framesometimes becomes a very critical practical problem.
A perfect frame is the one that is able to identify each element only once and
these frames are very rarely available in the real life.
The sample frames that we have selected from the Population are the investors
in the broking firm on the basis of which the data analysis will be conducted with
the help of the Questionnaire.
Sample selected would be of 75 questionnaires.
DATA COLLECTION TOOL
QUESTIONNAIRE
A questionnaire is a research instrument consisting of a series ofquestions and
other prompts for the purpose of gathering informationfrom respondents. Although they are often designed for statisticalanalysis of the responses.
A questionnaire having various questions regarding the employee perception for
the safety and health related measures taken in the manhar processor.Based on
this questionnaire analysis and interpretation is done.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 48/81
DATA ANALYSIS AND INTERPRETATION
1) Management visibly demonstrates an interest in the safety and health of
their employees
Valid 75
Missing 0
management visibly demonstrates an interest in the safety and health of their employees
Frequency Percent Valid PercentCumulativePercent
strongly agree 10 13.3 13.3 13.3
Agree 32 42.7 42.7 56.0
neither agree nor disagree 21 28.0 28.0 84.0
Disagree 8 10.7 10.7 94.7
strongly disagree 4 5.3 5.3 100.0
Total 75 100.0 100.0
INTERPRETATION: From the above table, we can interpret that the 42.7%
employees agree, 10.7% employees does not agree, 13.3% employees strongly
agree,5.3% employees strongly disagree and 28% employees neither agree
management visibly …
strongly
disagree
disagreeneither
agree
nor
disagree
agreestrongly
agree
F r e q u e n c y
40
30
20
10
0
management visibly demonstrates an
interest in the safety and health of their
employees
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 49/81
nordisagree on that the management shows interest in the safety and health of
their employees.
2)I feel my department is flexible in adjusting work assignments according
to employee safety considerations.N Valid 75
Missing 0
department is flexible in adjusting work assignment according to safety consideration
Frequency Percent Valid PercentCumulativePercent
strongly agree 5 6.7 6.7 6.7
Agree 30 40.0 40.0 46.7
neither agree nor disagree 26 34.7 34.7 81.3
Disagree 13 17.3 17.3 98.7
strongly disagree 1 1.3 1.3 100.0
Total 75 100.0 100.0
INTERPRETATION: From the above table, we interpret 40% of employees
agree,17.3% of employees disagree,6.7% of employees strongly agree,1.3% of
employees strongly disagree and 34.7% of employees are neutral that their
department assign them a work after undertaking all safety measures.
department is flexible in adjusting work assignment according to safety consideration
strongly disagreedisagreeneither agree nor
disagree
agreestrongly agree
F r e q u e n c y
30
20
10
0
department is flexible in adjusting work assignment according to safety consideration
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 50/81
3)Identified safety and health concerns or hazards are addressed or corrected
in a timely manner
Valid 75Missing 0
identified safety and health concerns or hazards are addressed or corrected in a timely manner
Frequency Percent Valid PercentCumulativePercent
strongly agree 3 4.0 4.0 4.0
agree 34 45.3 45.3 49.3
neither agree nor disagree 29 38.7 38.7 88.0
disagree 7 9.3 9.3 97.3
strongly disagree 2 2.7 2.7 100.0Total 75 100.0 100.0
INTERPRETATION: From the above table, we interpret 45.3% of employees
agree, 9.3% of employees disagree,4% of employees strongly agree,2.7% of
employees strongly disagree and 38.7% of employees neither agree nor
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 51/81
disagree that their company identify and correct safety and health hazards in a
timely manner.
4) The health and safety rules of this organization have been clearlyexplained to me.
Valid 75
Missing 0
health and safety rules of organization have been clearly explained to me
Frequency Percent Valid PercentCumulativePercent
strongly agree 8 10.7 10.7 10.7
agree 27 36.0 36.0 46.7neither agree nor disagree 26 34.7 34.7 81.3
disagree 11 14.7 14.7 96.0
strongly disagree 3 4.0 4.0 100.0
Total 75 100.0 100.0
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 52/81
INTERPRETATION: From the above table, we interpret 36% of employees
agree,14.7% of employees disagree,10.7% of employees strongly agree,4%
ofemployees strongly disagree and 34.7% of employees neither agree nor
disagree that their company has explained them all the health and safety rules.
5) Workplace accidents and/or near misses are sometimes not reported.
Valid 75
Missing 0
workplace accident and/or near misses are sometimes not reported
Frequency Percent Valid PercentCumulativePercent
strongly agree 2 2.7 2.7 2.7
agree 10 13.3 13.3 16.0
neither agree nor disagree 31 41.3 41.3 57.3
disagree 22 29.3 29.3 86.7
strongly disagree 10 13.3 13.3 100.0
Total 75 100.0 100.0
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 53/81
INTERPRETATION: From the above table, we interpret 13.3% of employees
agree,29.3% of employees disagree,2.7% strongly agree,13.3% of employees
strongly disagree, and 41.3% of employees neither agree nor disagree that the
workplace accidents are sometimes not reported in their organization.
6) My supervisor often observes my work practices for the purpose ofprotecting my safety and health.
Valid 75
Missing 0
my supervisor often observes my work practises for all the purpose of protecting my safety andhealth
Frequency Percent Valid Percent
Cumulative
PercentValid strongly agree 7 9.3 9.3 9.3
Agree 23 30.7 30.7 40.0
neither agree nor disagree 29 38.7 38.7 78.7
Disagree 12 16.0 16.0 94.7
strongly disagree 4 5.3 5.3 100.0
Total 75 100.0 100.0
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 54/81
INTERPRETATION: From the above table, we interpret 30.7% of employees
agree,16% of employees disagree,9.3% of employees strongly agree,5.3% of
employees strongly disagree and 38.7% of employees are neutral, that their
supervisor observes their work practices in order to protect their health and
safety.
7) The health and safety training program offered by my organization meet
my needs.
Valid 75
Missing 0
health and safety training program offered by my organization meet my needs
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 3 4.0 4.0 4.0
Agree 29 38.7 38.7 42.7
neither agree nor disagree 23 30.7 30.7 73.3
Disagree 11 14.7 14.7 88.0
strongly disagree 9 12.0 12.0 100.0
Total 75 100.0 100.0
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 55/81
INTERPRETATION: From the above table, we interpret, 38.7% of employees
agree,14.7% of employees disagree,4% of employees strongly agree,12% of
employees strongly disagree and 30.7% of employees are neither agree nor
disagree that the health and safety programmes offered in their organization are
as per their needs. .
8) If I saw another employee committing an unsafe practice, I would say
something directly to him or her.
Valid 75
Missing 0
if i saw another employee an unsafe practise,i would say something directly to him or her
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 9 12.0 12.0 12.0
agree 20 26.7 26.7 38.7
neither agree nor disagree 22 29.3 29.3 68.0
disagree 18 24.0 24.0 92.0
strongly disagree 6 8.0 8.0 100.0
Total 75 100.0 100.0
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 56/81
INTERPRETATION: From the above table, we interpret 26.7% of employees
agree,24% of employees disagree,12% of employees strongly agree, 8% of
employees strongly disagree and 29.3% neither agree nor disagree that if they
saw another employee committing an unsafe practice then they will say directly
to him.
9) If I have a concern about health and safety, and my supervisor is not
available, I know whom to contact..
Valid 75
Missing 0
if i have a concern about health and safety and my supervisor is not available.i know whom to
contact
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 8 10.7 10.7 10.7
agree 25 33.3 33.3 44.0
neither agree nor disagree 30 40.0 40.0 84.0
disagree 7 9.3 9.3 93.3
strongly disagree 5 6.7 6.7 100.0
Total 75 100.0 100.0
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 57/81
INTERPRETATION: From the above table, we interpret 33.3% of employees
agree,9.3% of employees disagree,10.7% of employees strongly agree,6.7% of
employees strongly disagree and 40% neither agree nor disagree that whom tocontact in absence of their supervisor, in concern of their health and safety.
10) Health and safety is a high priority when I am performing my job
responsibilities.
Valid 75
Missing 0
health and safety training program offered by my organization meet my needs
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 3 4.0 4.0 4.0
agree 29 38.7 38.7 42.7
neither agree nor disagree 23 30.7 30.7 73.3
disagree 11 14.7 14.7 88.0
strongly disagree 9 12.0 12.0 100.0
Total 75 100.0 100.0
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 58/81
INTERPRETATION: From the above table, we interpret 38.7% of employees
agree,5.3% of employees disagree,32% of employees strongly agree,8% of
employees strongly disagree and 16% neither agree nor disagree that health and
safety is their high priority while performing the job.
11) Rewards and positive feedback are a good way to increase health andsafety awareness levels.
Valid 75
Missing 0
rewards and positive feedback are a good way to increase health and safety awareness levels
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 9 12.0 12.0 12.0agree 26 34.7 34.7 46.7
neither agree nor disagree 23 30.7 30.7 77.3
disagree 13 17.3 17.3 94.7
strongly disagree 4 5.3 5.3 100.0
Total 75 100.0 100.0
INTERPRETATION: From the above table, we interpret 34.7% of employees
agree,17.3% of employees disagree,12% of employees strongly agree,5.3% of
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 59/81
employees strongly disagree and 30.7% neither agree nor disagree that rewards
and positive feedback are a good way to increase health and safety awareness
levels.
12) I know what to do in case of an emergency (i.e. fire, tornado, chemical
spill, etc.).
Valid 75
Missing 0
i know what to do in case of an emergency
Frequency Percent Valid PercentCumulative
Percent
Valid yes 55 73.3 73.3 73.3no 20 26.7 26.7 100.0
Total 75 100.0 100.0
INTERPRETATION: From the above table, we interpret 73.3% of employees
knows what to do in case of emergency and 26.7% don‟t know what to do in
case of emergency.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 60/81
13) Safe operating procedures (SOP's) for using equipment/machines are
reviewed and revised as necessary.
Valid 75
Missing 0
safe operating procedures for using equipment/machines are reviewed and revised are necessary
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 3 4.0 4.0 4.0
agree 29 38.7 38.7 42.7
neither agree nor disagree 23 30.7 30.7 73.3
disagree 17 22.7 22.7 96.0
strongly disagree 3 4.0 4.0 100.0
Total 75 100.0 100.0
INTERPRETATION: From the above table, we interpret 38.7% of employeesagree,22.7% of employees disagree,4% of employees strongly agree,4% of
employees strongly disagree and 30.7% neither agree nor disagree that safe
operating procedures for using equipment/machines are reviewed and revised as
per necessity.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 61/81
14)Health and safety inspections of my work area/department are
conducted at regular intervals.
Valid 75
Missing 0
health and safety inspection of my work area/department are conducted at regular intervals
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 5 6.7 6.7 6.7
agree 23 30.7 30.7 37.3
neither agree nor disagree 40 53.3 53.3 90.7
disagree 5 6.7 6.7 97.3
strongly disagree 2 2.7 2.7 100.0
Total 75 100.0 100.0
INTERPRETATION: From the above table, we interpret 30.7% of employees
agree,6.7% of employees disagree,6.7% of employees strongly agree,2.7% of
employees strongly disagree and 53.3% neither agree nor disagree that health
and safety inspection of my work area/department are conducted at regular
intervals
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 62/81
15) All new employees are properly trained in health and safety rules and
work practices.
Valid 75
Missing 0
all new employee are properly trained in health and safety rules and work practices
Frequency Percent Valid PercentCumulative
Percent
Valid strongly agree 4 5.3 5.3 5.3
agree 39 52.0 52.0 57.3
neither agree nor disagree 18 24.0 24.0 81.3
disagree 11 14.7 14.7 96.0
strongly disagree 3 4.0 4.0 100.0
Total 75 100.0 100.0
INTERPRETATION: From the above table, we interpret 52% of employees
agree,14.7% of employees disagree,5.3% of employees strongly agree,4% of
employees strongly disagree and 24% neither agree nor disagree that all new
employee are properly trained in health and safety rules and work practices
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 63/81
16) I know the name of my organization's safety coordinator and how I can
contact him or her?
Valid 75
Missing 0
i know the name of safety coordinator and how i can contact him or her
Frequency Percent Valid PercentCumulative
Percent
Valid yes 63 84.0 84.0 84.0
no 12 16.0 16.0 100.0
Total 75 100.0 100.0
=
INTERPRETATION: From the above table, we interpret 84% of employees know
the name of their safety coordinator whereas 16% don‟t know the name of their
safety coordinator.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 64/81
CHI SQUARE TEST:-
TEST No. 1
Null Hypothesis (HO): There is no significant difference between accidentsometime not reported and health and safety programme offered by organization.
Alternative Hypothesis (H1): There is significant difference between accident
sometime not reported and health and safety programme offered by organization.
Significance level: 0.05
Chi-Square Statistic
Case Processing Summary
Cases
Valid Missing Total
N Percent N Percent N Percent
workplace accident and/or
near misses are sometimes
not reported * health and
safety training program
offered by my organizationmeet my needs
75 100.0% 0 .0% 75 100.0%
workplace accident and/or near misses are sometimes not reported * health and safety
training program offered by my organization meet my needs Crosstabulation
health and safety training program offered by my
organization meet my needs
Total
strongly
agree agree
neither agree
nor disagree disagree
strongly
disagree
workplace
accident and/or
near misses are
sometimes not
reported
strongly
agree
Count 0 1 1 0 0 2
Residual .0 .2 .4 .3 .2
Std. Residual .3 .3 .5 .5 .5
agree Count 2 6 1 1 0 10
Residual 1.6 2.1 -2.1 .5 1.2
Std. Residual 2.5 .1 -1.2 .4 1.1
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 65/81
Neither
agree nor
disagree
Count 1 12 11 2 5 1
Residual .2 .0 1.5 2.5 1.3
Std. Residual .2 .0 .5 1.2 .7
disagree Count 0 8 8 4 2 22
Residual .9 .5 1.3 .8 .6
Std. Residual .9 .2 .5 .4 .4
strongly
disagree
Count 0 2 2 4 2 0
Residual .4 1.9 -1.1 2.5 .8
Std. Residual .6 .9 -.6 2.1 .7
Total Count 3 29 23 11 9 75
Chi-Square Tests
Value Df
Asymp. Sig. (2-
sided)
Pearson Chi-Square 21.454a
16 .162
Likelihood Ratio 20.748 16 .188
Linear-by-Linear Association 7.745 1 .005
N of Valid Cases 75
a. 21 cells (84.0%) have expected count less than 5. The minimum
expected count is .08.
INTERPRETATION:
Since the asymptotic value is 0.162, which is greater than 0.05, so we accept Ho.
i.e.There is no significant difference between accident sometime not reported
and health and safety programme offered by organization are up to the needs of
employees.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 66/81
TEST No. 2
Null Hypothesis (HO): There is no significant difference between employees
concern about health and safety and their priority to health and safety while they
performing the job.
Alternative Hypothesis (H1): There is significant difference between employees
concern about health and safety and their priority to health and safety while they
performing the job.
Significance level: 0.05
Chi-Square Statistic
Case Processing Summary
Cases
Valid Missing Total
N Percent N Percent N Percent
workplace accident and/or
near misses are sometimes
not reported * health and
safety training program
offered by my organization
meet my needs
75 100.0% 0 .0% 75 100.0%
if i have a concern about health and safety and my supervisor is not available.i know whom
to contact * health and safety is high priority when i am performing my job Crosstabulation
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 67/81
health and safety is high priority when i am
performing my job
Total
strongly
agree agree
neither agree
nor disagree Disagree
strongly
disagree
if i have a
concern
about health
and safety
and my
supervisor is
not
available.i
know whom
to contact
strongly
agree
Count 1 4 2 0 1 8
Residual -1.6 .9 .7 -.4 .4
Std. Residual 1.0 .5 .6 -.7 .4
agree Count 11 10 3 0 1 25
Residual 3.0 .3 -1.0 -1.3 -1.0
Std. Residual 1.1 .1 -.5 -1.2 -.7
neither
agreenor
disagree
Count 7 12 5 4 2 30
Residual -2.6 .4 .2 2.4 -.4
Std. Residual -.8 .1 .1 1.9 -.3
disagree Count 4 2 1 0 0 7
Residual 1.8 .7 -.1 -.4 -.6
Std. Residual 1.2 4 -.1 -.6 -.7
strongly
disagree
Count 1 1 1 0 2 5
Residual -.6 -.9 .2 -.3 1.6
Std. Residual -.5 -.7 .2 -.5 2.5
Total Count 24 29 12 4 6 75
Chi-Square Tests
Value Df
Asymp. Sig. (2-
sided)
Pearson Chi-Square 19.769a
16 .231
Likelihood Ratio 18.654 16 .287
Linear-by-Linear Association 1.030 1 .310
N of Valid Cases 75
a. 21 cells (84.0%) have expected count less than 5. The minimum
expected count is .27.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 68/81
INTERPRETATION:
Since the asymptotic value is 0.231, which is greater than 0.05, so we accept Ho.
i.e. There is no significant difference between employees concern about their
own health and know whom to contact in absence of their supervisor and their
priority to health and safety while they performing their job.
TEST No. 3
Null Hypothesis (HO): There is no significant difference between health and
safety inspection of work conducted at regular interval and health and safety
training programme offered by organization,
Alternative Hypothesis (H1): There is significant difference between health and
safety inspection of work conducted at regular interval and health and safety
training programme offered by organization,
Significance level: 0.05
Chi-Square Statistic
Case Processing Summary
Cases
Valid Missing Total
N Percent N Percent N Percent
workplace accident and/or
near misses are sometimes
not reported * health and
safety training program
offered by my organization
meet my needs
75 100.0% 0 .0% 75 100.0%
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 69/81
workplace accident and/or near misses are sometimes not reported * health and safety
training program offered by my organization meet my needs Crosstabulation
health and safety training program offered
by my organization meet my needs
Total
strongly
agree agree
neither
agree nor
disagree disagree
strongly
disagree
workplace
accident
and/or near
misses are
sometimes not
reported
strongly agree Count 0 0 3 0 0 3
Residual -.2 -.9 1.4 -.2 -.0
Std. Residual -.4 -1.0 1.1 -.4 -.3
agree Count 2 12 12 3 0 29
Residual .1 3.1 -3.5 1.1 -.8
Std. Residual .0 1.0 -.9 .8 -.9
neither agree
nor disagree
Count 1 7 13 1 1 23
Residual -.5 .0 .7 -.4 .5
Std. Residual -.4 .0 .2 -.5 .4
disagree Count 0 4 7 0 0 11
Residual -.7 .6 1.1 .7 -.3
Std. Residual -.9 .3 .5 .9 -.5
strongly
disagree
Count 2 0 5 1 1 9
Residual 1.4 -2.8 .2 .4 .8
Std. Residual 1.8 -1.7 .1 .5 1.6
Total Count 5 23 40 5 2 75
Chi-Square Tests
Value Df
Asymp. Sig. (2-
sided)
Pearson Chi-Square 17.314a
16 .366
Likelihood Ratio 21.250 16 .169
Linear-by-Linear Association .452 1 .502
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 70/81
Chi-Square Tests
Value Df
Asymp. Sig. (2-
sided)
Pearson Chi-Square 17.314a
16 .366
Likelihood Ratio 21.250 16 .169
Linear-by-Linear Association .452 1 .502
N of Valid Cases 75
a. 20 cells (80.0%) have expected count less than 5. The minimum
expected count is .08.
INTERPRETATION:
Since the asymptotic value is 0.366, which is greater than 0.05, so we accept Ho.
i.e.There is no significant difference between health and safety inspection of work
conducted at regular interval in the organization and health and safety training
programme offered by organization are according to the employees need.
TEST No. 4
Null Hypothesis (HO): There is no significant difference between health and
safety inspection of work conducted at regular interval and all new employee are
properly trained in health and safety rules and work practices.
Alternative Hypothesis (H1):There is significant difference between health and
safety inspection of work conducted at regular interval and all new employee are
properly trained in health and safety rules and work practices.
Significance level: 0.05Chi-Square Statistics
Case Processing Summary
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 71/81
Cases
Valid Missing Total
N Percent N Percent N Percent
health and safety trainingprogram offered by myorganization meet my
needs * all new employeeare properly trained inhealth and safety rulesand work practices
75 100.0% 0 .0% 75 100.0%
workplace accident and/or near misses are sometimes not reported * health and safety
training program offered by my organization meet my needs Crosstabulation
health and safety training program offered
by my organization meet my needs
Total
strongly
agree agree
neither
agree nor
disagree disagree
strongly
disagree
workplace
accident
and/or near
misses are
sometimes not
reported
strongly agree Count 0 3 0 0 0 3
Residual -.2 1.4 -.7 -.4 -.1
Std. Residual -.4 1.2 -.8 -.7 -.3
agree Count 4 12 8 5 0 29
Residual 2.5 -3.1 1.0 .7 -1.2
Std. Residual 2.0 -.8 .4 .4 -1.1
neither agree
nor disagree
Count 0 12 6 3 2 23
Residual -1.2 0 .5 -.4 1.1
Std. Residual -1.1 .0 .2 -.2 1.1
disagree Count 0 5 2 3 1 11
Residual -.6 -.7 -.6 1.4 .6
Std. Residual -.8 -.3 -.8 1.1 .4
strongly
disagree
Count 0 7 2 0 0 9
Residual -.5 2.3 -.2 -1.3 -.4
Std. Residual -.7 1.1 -.1 -1.1 -.6
Total Count 4 39 18 11 3 75
Chi-Square Tests
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 72/81
Value Df
Asymp. Sig. (2-
sided)
Pearson Chi-Square 17.373a
16 .362
Likelihood Ratio 21.607 16 .156
Linear-by-Linear Association .271 1 .603
N of Valid Cases 75
a. 20 cells (80.0%) have expected count less than 5. The minimum
expected count is .12.
INTERPRETATION:
Since the asymptotic value is 0.362, which is greater than 0.05, so we accept Ho.
i.e. There is no significant difference between health and safety inspection of
work conducted at regular interval and all new employee are properly trained in
health and safety rules and work practices.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 73/81
RESULT AND FINDINGS
From the study, the researcher has come to know that most of the respondents
agree that they are safe and secure in their organization; the management has
taken the best efforts to maintain cordial relationship with the employees. Due to
the working conditions prevailing in this company, the employees feel safe and
secure which turns to fewer turnovers. From the study, I have come to know that
most of the employees were satisfied with the health and safety measures
provided by MANHAR. The employees of MANHAR get more benefits compare
to other companies.
The health and safety rules of the organization have been clearly
explained to employees.
Employees feel department is flexible in adjusting work assignments
according to employee safety considerations.
Supervisor often observes work practices of employees for the purpose of
protecting their safety and health.
The health and safety training program offered by the organization meet
the needs of employees.
Safe operating procedures (SOP's) for using equipment/machines are
reviewed and revised as necessary.
Health and safety inspections of work area/department are conducted at
regular intervals.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 74/81
LIMITATION OF STUDY:
1. Sample size of study is only 75.
2. Some of the respondents were not responding to some of the questions.
3. Data collected is based on questionnaire.
4. The information collected by the observation method is very limited.
5. The result would be varying according to the individuals as well as time.
6. Some respondents hesitated to give the actual situation; they feared that
management would take any action against them.
7. The findings and conclusions are based on knowledge and experience of the
respondents sometime may subject to bias.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 75/81
CONCLUSION
In the organization most of employees are satisfied with all the facilities provided
by company. But there are some employees also who are not satisfied with the
companies health and safety measures. Management should try to convert
unsatisfied employees in to satisfied employees. Because if employee is not
satisfied than the he is not able to give his 100% to his work and the productivity
of employee decrease. So management should try to satisfy his employees
because employees are the assets of the company not liabilities. According to
research it is clear that the most of employees are satisfied with their companies
health and safety measures. And main factors for their satisfaction are traininggiven to work on machines, protection given against chemical, earplugs given to
the employees against noise created by the machineries and hygiene working
climates.
According to the research there are also some employees who are not satisfied
with the health and safety measures adopted by the company due to stated
reasons, not a hygiene climate in terms of urinals, spittoons, canteen and
drinking facility and security.
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 76/81
Annexure
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 77/81
BIBLIOGRAPHY
Argyris,C. (1964). Integrating the individual and the organization. New York:Wiley.
Bowen. E., & Ostroff, C. (2004). Understanding HRM-firm performance linkages:The role of
"strength “of the HR system. Academy of Management Review, 29,203-
221.Emery, R. E., & Trist, E. L. (1960).Socio-technical systems. In C. W.
Churchman and M.Gross,E., & Etzioni, A. (1985).Organizations in
society.Englewood Cliffs, NJ: Prentice-Hall. Harter, J. K., Schmidt, F. L., &
Hayes, T. L.(2002). Business-unit level relationship between
employee satisfaction, employee engagement, and business outcomes: A meta-analysis.
Journal ofApplied Psychology, 87,268-279.
Ostroff,C. (1992). The relationship between satisfaction, attitudes, and
performance: An organizational Level Analysis.Journal of Applied
Psychology, 77,963-974.
Peterson,S. J., & Luthans, F. (2006). The impact of financial and nonfinancial
incentives on business-unit outcomes over time. Journal of Applied
Psychology, 91, 156-165.
Ryan,A. M., Schmitt, M. J., & Johnson, R. (1996). Attitudes and effectiveness:
Examining relations at an organizational level. Personnel Psychology, 49,
853-882.
Schneider,B., & Schmitt, N. (1986). Staffing organizations.Glenview, IL: Scott,
Foresman. Schneider, B., Hanges, P. J., Smith, D. B.,& Salvaggio, A. N. (2003).
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 78/81
Which comes first:
Employee attitudes or organizational financial and market performance? Journal of
Applied Psychology, 88, 836-851.
Schneider,B., White, S. S., & Paul, M. C. (1998). Linking service climate and
customer perceptions of service quality: Tests of a causal model.Journal
of Applied Psychology,
83,150-163.
Wright, P. M., Dun ford, B. B., & Snell, S. A. (2001). Human resources and the
resource-based view of the firm.Journal of Management, 18, 295-320.
Wright, P. M., Gardner, T. M., Moynihan, L.M., & Allen, M. R. (2005). The
relationship between HR practices and firm performance: Examining
causal order. Personnel Psychology,58, 409-446.
Zohar,D., & Luria, G. (2005). A multilevel model of safety climate: Cross-level
relationships between organization and group-level climates. Journal of
Applied Psychology, 90,616-
628.
Books:
Kotler Philip and KellerKevin , marketing management ,publisher:
prentice hall ; 13 edition. Gupta C>B>,Human Resource Management, Publisher: Sulatan
Chand & sons,13th
edition,2011
Ashwathappa K, Bhat Shridhar K.,Producation and Operations
Management,Publisher:HimalayaPub. House
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 79/81
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 80/81
7/31/2019 Rinkal Soni Sip Report1
http://slidepdf.com/reader/full/rinkal-soni-sip-report1 81/81