roller bushing catalog - engine cooling … 5 mfr side bar c/l to c/l spring width bushing o.d. rear...
TRANSCRIPT
�
You need strong protection from roadcontaminants and moisture that constantlythreaten your vehicles’ suspension and your
bottom line. Horton Roller Bushings are the trouble-free solution to frequent repairs and vehicle downtime.
Reliability Matters.
Traditional spring pins and bushings aren’t designed towithstand the daily abuses of the road. Roller Bush-ings from Horton provide the long-term lubrication necessary for a properly maintained suspension sys-tem. Now you can eliminate the worry of seized pins and front wheel hop. Installation is quick, easy, and the results include a smoother ride, improved handling and less chassis stress.
Horton Solution
Special Ribbed CasingEasier installation; requires lessforce to install and no specialtool for spring eye expansion
Patented Needle BearingsProvides over 7 linear feet ofgrease grooves for maximumlubrication and minimummaintenance
Dual Lip SealsKeeps dirt out, allows oldgrease to escape, and leavesclean grease in place
RolleR Bushings
Strong Protection
Trouble-Free Solution.
You’ve got too much riding on your suspension. Don’t gamble with springs, pins or low-quality bushings. Horton Roller Bushings last for hundreds of thousands of miles so they rarely need to be replaced—saving you costly down-time and repair costs.
Time to Upgrade.
Horton Roller Bushings deliver benefits the moment they’re installed. Drivers will notice a smoother ride and improvedhandling. Chassis stress will be reduced and front wheel hop eliminated. And your trucks will remain on the road far longer than those with conventional springs and pins.
�
GENERAL SPECIFICATIONS (Ordering Information) ...................................................3-4
FRONT AND REAR BUSHING APPLICATIONS ............................................................5-7 Bluebird .......................................................................................................................5 Ford/Sterling ................................................................................................................5 Freightliner ...................................................................................................................5 GMC ............................................................................................................................5 International .................................................................................................................6 Kenworth .....................................................................................................................6 Mack ............................................................................................................................6 Marmon .......................................................................................................................6 Ottawa .........................................................................................................................6 Peterbilt .......................................................................................................................6 Tyco . ..........................................................................................................................7 Volvo ............................................................................................................................7 Western Star ...............................................................................................................7
FRONT AND REAR BUSHING KITS (Standard Parts) ................................................7-�0 Rear Kit with Standard Side Bars (Ribbed Bushing in Hanger Bracket) ....................7 Rear Kit with Threaded Side Bars ...............................................................................8 Rear Kit with Threaded Bushing ..................................................................................8 Rear Kit with Standard Side Bars (Smooth Bushing in Hanger Bracket) ....................9 Front Kit on Bracket with Locking Caps ......................................................................9 Front Kit on Bracket with Step Pin and Collar ...........................................................�0 Peterbilt Air Ride Pin and Bushing Kit ......................................................................�0
PARTS AND REPAIR KITS (Front Anchor Pin and Rear Shackle).............................��-��
TaBle of ConTenTs
3
5
MFR SIDEBARC/L TO C/L
SPRINGWIDTH
BUSHING O.D. REAR SHACKLE (1 per side)
FRONT ANCHOR (1 per truck)
MAX.AXLE
RATING
COMMENTS
EYE HANGAR KIT FIGUREP. 7-10
KIT FIGUREP. 7-10
BLUEBIRD
3.75 4.00 1.50 1.50 994534 4 - - 20,000 -
FORD
/
STERLING
- - - 1.71 994528 - - - 20,000 Ford hanger bracket (F7HT 5338 AA) & Horton roller bushing only
- - - 1.71 994529 - - - 20,000 Ford hanger bracket (F8HT 5338 BA) & Horton roller bushing only
- - - 1.71 994567 - - - 20,000 Ford hanger bracket (F7HT 5338 BA) & Horton roller bushing only
3.75 4.00 1.25 1.25 994519 1 - - 12,000 Steel side bars
5.25 4.00 2.25 2.25 994524 4 - - 20,000 -
3.75 4.00 1.25 1.25 994438 1 - - 12,000 Aluminum side bars. 2 ribbed bushings
4.00 4.00 1.25 1.25 994473 1 - - 12,000 -
4.62 4.00 1.25 1.25 994439 1 - - 12,000 2 ribbed bushings.
3.69 4.00 1.42 1.42 994503 1 - - 16,000 -
- 4.00 1.50 - - - 994434 6 20,000 Replacement of OEM installed bronze bushing in heavy duty suspension Cur-rently, nothing offered to retrofit standard suspension with factory installed bronze bushing.
3.50 4.00 1.50 1.50 994533 1 - - 20,000 Steel side bars. Replacement of OEM installed bronze bushing in the heavyduly or standard suspension
4.00 4.00 1.50 1.50 994507 1 - 6 20,000 Ford Aero - 1994 & Later
- 4.00 1.70 - 994510 - 994509 6 20,000 Straight pin. Does not use collar as pictured in Figure 6. Pin length 6.90”. Replacement of OEM installed Horton bushing in heavy-duty suspension.
- 4.00 1.70 - 994510 - 994510 6 20,000 Straight pin. Does not use collar as pictured in Figure 6. Pin length 6.65”. Replacement of OEM installed Horton bushing in standard suspension.
- - - 1.71 994597 - - - 20,000 Ford hanger bracket (F6HT-5335-CA) & Horton roller bushing only.
5.25 4.00 2.25 2.25 994524 4 - - 20,000 For HX chassis.
FREIGHTLINER
4.25 4.25 1.38 1.38 994424 4 - - 16,000 -
5.25 3.50 1.50 1.50 994404 4 994487 6 20,000 -
5.25 4.00 1.50 1.50 994408 4 994434 6 20,000 -
5.25 4.00 1.50 1.63 994409 4 994434 6 20,000 -
4.13 4.00 1.50 1.63 994410 4 994434 6 20,000 -
4.13 4.00 1.50 1.50 994475 4 994434 6 20,000 112 heavy-duty
5.25 3.50 1.61 1.50 994485 4 - - 20,000 To 1982 cab over w/ #16-11265 spring
5.25 3.50 1.63 1.50 994406 4 994488 6 20,000 -
5.25 3.50 1.63 1.63 994407 4 994488 6 20,000 -
5.25 4.00 1.63 1.63 994411 4 994489 6 20,000 -
5.25 4.00 2.25 2.25 994524 4 - - 20,000 Century - 1996 & newer
- 4.00 1.50 1.50 994603 4 - - 20,000 No side bars. Hanger width 3.50”.
GMC3.50 3.00 1.69 1.69 994420 4 - - 20,000 -
3.50 4.00 1.69 1.69 994421 4 - - 20,000 -
If you are unable to locate an application that meets your specifications, see Page 4.
Front and rear BuSHing appliCationSBLUEBIRD - GMC
SELECTING A ROLLER BUSHING
See pages 5-7 for application tables.
1. Locate truck manufacturer in the header and/or MFR. column.
2. Locate side bar centerline width in the SIDE BAR C/L to C/L column (See
Diagram D, Page 4).
3. Locate the width of the spring in the SPRING WIDTH column (See
Diagram C, Page 4).
4. Locate the O.D. of the bushing in the BUSHING O.D. column. See the proper columns for bushing O.D. EYE and HANGER information.
5. Locate the REAR SHACKLE and FRONT ANCHOR information in the respective columns. The KIT numbers are shown as well as FIGURE num-bers for pictorial representations on pages 7-10.
6. Maximum axle ratings appear in the MAX. AXLE RATING column.
7. Additional application information is specified in the COMMENTS col-umn.
Order the Horton roller bushing kit listed.
NOTE: In most cases, Horton roller bushing pins will be a different size than standard pins.
When you have identified the proper model, confirm it with your Hortondistributor or dealer when placing your order.
geneRal speCifiCaTions (oRdeRing infoRmaTion)
ABBREVIATIONS USED THROUGHOUT THIS CATALOG
C/L = Center Line Hex. = Hexagon Max. = MaximumC.O.E. = Cab Over Engine I.D. = Inner Diameter w/ = with MFR. = Manufacturer O.D. = Outer Diameter w/o = withoutGMC = General Motors Corp OEM = Original Equipment Manufacturer
4
Call Horton Customer Service at 1-800-621-1320 and provide them with the following information. Horton will make every effort possible to meet your application specifications.
Hanger Bracket Width
Spring Width
Bushing Width
Center Line Distance
NOTE: Some Horton roller bushing kits use a ribbed bushing for spring eye applications. In most cases, the bushing used in the hanger bracket will be smooth (See Diagrams A and B).
DO NOT use a spring eye expander for the installation of ribbed roller bushings (See Diagram B).
geneRal speCifiCaTions (oRdeRing infoRmaTion)
CENTER LINETO CENTER LINE DISTANCE
maXimum aXle RaTings
PIN SIZE (INCHES) POUNDS
0.8��5 ��,000
0.8750 �6,000
�.0000 �0,000
�.�500 �0,000
KiTs ReQuiRed peR TRuCK
QUANTITY KIT
� Rear Shackle � Front Spring Pin
HANGER BRACKETWIDTH
SPRING WIDTH
BUSHING WIDTH
Ribbed Roller BushingSmooth Roller Bushing
DIAGRAM A DIAGRAM B
DIAGRAM C
DIAGRAM D
5
MFR SIDE BAR C/L TO C/L
SPRING WIDTH
BUSHING O.D. REAR SHACKLE (1 per side)
FRONT ANCHOR (1 per truck)
MAX. AXLE
RATING
COMMENTS
EYE HANGAR KIT FIGURE P. 7-10
KIT FIGURE P. 7-10
BLUE BIRD
3.75 4.00 �.50 �.50 994534 4 - - �0,000 -
FORD / STERLING
- - - �.7� 9945�8 - - - �0,000 Ford hanger bracket (F7HT 5338 AA) & Horton roller bushing only
- - - �.7� 9945�9 - - - �0,000 Ford hanger bracket (F8HT 5338 BA) & Horton roller bushing only
- - - �.7� 994567 - - - �0,000 Ford hanger bracket (F7HT 5338 BA) & Horton roller bushing only
3.75 4.00 �.�5 �.�5 9945�9 � - - ��,000 Steel side bars
5.�5 4.00 �.�5 �.�5 9945�4 4 - - �0,000 -
3.75 4.00 �.�5 �.�5 994438 � - - ��,000 Aluminum side bars. � ribbed bushings
4.00 4.00 �.�5 �.�5 994473 � - - ��,000 -
4.6� 4.00 �.�5 �.�5 994439 � - - ��,000 � ribbed bushings.
3.69 4.00 �.4� �.4� 994503 � - - �6,000 -
- 4.00 �.50 - - - 994434 6 �0,000 Replacement of OEM installed bronze bushing in heavy duty suspension Cur-rently, nothing offered to retrofit standard suspension with factory installed bronze bushing.
3.50 4.00 �.50 �.50 994533 � - - �0,000 Steel side bars. Replacement of OEM in-stalled bronze bushing in the heavy-duty or standard suspension
4.00 4.00 �.50 �.50 994507 � - 6 �0,000 Ford Aero - �994 & Later
- 4.00 �.70 - 9945�0 - 994509 6 �0,000 Straight pin. Does not use collar as pictured in Figure 6. Pin length 6.90”. Replacement of OEM installed Horton bushing in heavy-duty suspension.
- 4.00 �.70 - 9945�0 - 9945�0 6 �0,000 Straight pin. Does not use collar as pictured in Figure 6. Pin length 6.65”. Replacement of OEM installed Horton bushing in standard suspension.
- - - �.7� 994597 - - - �0,000 Ford hanger bracket (F6HT-5335-CA) & Horton roller bushing only.
5.�5 4.00 �.�5 �.�5 9945�4 4 - - �0,000 For HX chassis.
FREIGHTLINER
4.�5 4.�5 �.38 �.38 9944�4 4 - - �6,000 -
5.�5 3.50 �.50 �.50 994404 4 994487 6 �0,000 -
5.�5 4.00 �.50 �.50 994408 4 994434 6 �0,000 -
5.�5 4.00 �.50 �.63 994409 4 994434 6 �0,000 -
4.�3 4.00 �.50 �.63 9944�0 4 994434 6 �0,000 -
4.�3 4.00 �.50 �.50 994475 4 994434 6 �0,000 ��� heavy-duty
5.�5 3.50 �.6� �.50 994485 4 - - �0,000 To �98� cab over w/ #�6-���65 spring
5.�5 3.50 �.63 �.50 994406 4 994488 6 �0,000 -
5.�5 3.50 �.63 �.63 994407 4 994488 6 �0,000 -
5.�5 4.00 �.63 �.63 9944�� 4 994489 6 �0,000 -
5.�5 4.00 �.�5 �.�5 9945�4 4 - - �0,000 Century - �996 & newer
- 4.00 �.50 �.50 994603 4 - - �0,000 No side bars. Hanger width 3.50”.
GMC3.50 3.00 �.69 �.69 9944�0 4 - - �0,000 -
3.50 4.00 �.69 �.69 9944�� 4 - - �0,000 -
If you are unable to locate an application that meets your specifications, see Page 4.
fRonT and ReaR Bushing appliCaTionsBLUEBIRD - GMC
6
* �.375 Threaded Bushing: Replaces OE Threaded Pin
fRonT and ReaR Bushing appliCaTionsINTERNATIONAL - PETERBILT
If you are unable to locate an application that meets your specifications, see Page 4.** For Kenworth Front Anchor Kits, 994570 is used to replace greaseless rubber mounted bushings. 99447� is used to replace greasable bushings.
MFR. SIDE BAR
C/L TO C/L
SPRING WIDTH
BUSHING O.D. REAR SHACKLE (1 per side)
FRONT ANCHOR (1 per truck)
MAX. AXLE
RATING
COMMENTS
EYE HANGAR KIT FIGURE P. 7-10
KIT FIGURE P. 7-10
INTERNATIONAL
4.00 4.00 THD* THD* 9945�� 3 - - ��,000 9600 Series - �995 & Newer
3.50 4.00 �.�5 �.�5 994433 � - - ��,000 Threaded side bar
3.50 3.00 �.50 �.50 9945�4 4 - - �0,000 School Bus
3.50 4.00 �.50 �.50 9944�6 � - - �0,000 Threaded side bars
4.00 4.00 �.75 �.50 99450� 4 - - �0,000 -
4.00 4.00 �.76 �.76 99450� 4 - - �0,000 -
4.3� 4.00 �.76 THD* 994403 3 - - ��,000 Except 4000 Series, �98� & older
4.00 4.00 �.76 THD* 994405 3 994486 5 ��,000 Threaded side bars
4.00 4.00 �.84 �.84 994605 - - - - -
3.�5 4.00 �.76 THD* 99443� 3 994486 5 ��,000 Except 5000 Series for 994486
4.3� 4.00 �.77 �.77 9944�5 4 994486 5 �0,000 -
- 4.00 �.50 - - - 994588 6 �0,000 -
3.50 4.00 �.�5 �.50 994606 � - - ��,000 �000, 3000, 4000, 8000 models Threaded side bars
3.�5 4.00 �.76 THD* 994607 3 - - ��,000 8000, 9000 models. Threaded side bars.
3.50 4.00 �.50 �.50 9946�3 4 - - �0,000 � smooth bushings.
4.00 4.00 �.84 �.84 994968 3 - - �0,000 9000 models. � ribbed bushings.
KENWORTH**
5.00 4.00 �.75 �.75 9944�6 4 994570 OR
99447�
6 �0,000 Offset side bar – T�000
4.00 4.00 �.75 �.75 9944�5 4 99447� OR
994570
6 �0,000 Older Conventional W900, uses 9944�5 if driver side aluminum hanger has been replaced with a steel hanger. Use 9944�7 or 994500 if aluminum.
4.00 4.00 �.75 �.75 9944�7 4 99447� OR
994570
6 �0,000 Offset side bar - New Conventional
4.00 4.00 �.75 �.75 994500 4 - - �0,000 Offset side bar - One threaded side bar, one thru hole side bar. Left side only.
4.00 4.00 �.75 �.75 9946�� 4 - - �0,000 Offset side bar - One threaded side bar, one thru hole side bar. Right side only.
MACK
4.00 3.50 �.76 �.76 9944�8 4 - - �0,000 CL model
4.00 3.44 �.87 �.88 9945�3 4 9945�� 6 �0,000 CH model
4.00 4.00 �.88 �.88 9944�9 4 - - �0,000 -
4.00 3.50 �.50 �.76 994587 4 994586 5 �0,000 RD & RB model
MAR-MON
3.50 4.00 �.50 �.50 99440� 4 - - �0,000 -
OTT-AWA
4.00 4.00 �.37 �.50 994593 4 - - ��,000 -
PETERBILT
3.50 3.50 �.50 �.50 994400 4 - - �0,000 59 conventional can only use this kit If equipped
with 3.50” wide hanger bracket
3.50 4.00 �.50 �.50 99440� 4 994434 6 �0,000 C.O.E. & Conventional
5.�5 4.00 �.50 �.50 994408 4 994434 6 �0,000 Setback
3.50 4.00 �.50 �.50 994483 4 - - �0,000 3.50 hanger width
5.00 STEEL
4.00 �.50 �.50 994474 7 994434 6 �0,000 Peterbilt Air Ride – �.50 Collar 3 smooth bushings.
4.6� 4.00 �.50 �.50 99460� 4 - - �0,000 387 model
5.�5 4.00 �.75 �.50 9946�0 4 - - - 387 model
3.50 4.00 �.75 �.50 9946�� 4 - - - 387 model
7
Front of Truck
fRonT and ReaR Bushing appliCaTionsTYCO - WESTERN STAR
fRonT and ReaR Bushing KiTs (sTandaRd paRTs)
REAR KIT WITH STANDARD SIDE BARS(RiBBed Bushing in hangeR BRaCKeT)
87
67
9
5
�
53
87
6
97
�0
If you are unable to locate an application that meets your specifications, see Page 4.
Figure 1
SIDE BAR C/L TO C/L
SPRING WIDTH
BUSHING O.D. REAR SHACKLE (1 per side)
FRONT ANCHOR (1 per truck)
MAX. AXLE
RATING
COMMENTS
EYE HANGAR KIT FIGURE P. 7-10
KIT FIGURE P. 7-10
TYCO 5.40 4.00 �.37 �.37 994599 4 - - �6,000 -
VOLVO
3.69 3.00 �.38 �.84 9944�9 4 - - �6,000 White GMC
3.69 4.00 �.38 �.38 9944�7 4 - - �6,000 W�A4�T Conventional - Used with Hendrickson springs. White Auto Car Volvo White
4.�5 4.00 �.38 �.38 9944�4 4 - - �6,000 White Auto Car
3.69 4.00 �.38 �.84 9944�8 4 - - �6,000 WG-64T - White GMC
3.69 4.00 �.39 �.38 9945�0 4 - - �6,000 Used with Krupp-Bruninghouse springs
3.50 4.00 �.74 �.77 994596 4 - - �0,000 VN model
WEST-ERN STAR
4.00 4.00 �.�5 �.�5 994473 4 - - ��,000 -
5.00 4.00 �.38 �.38 99447� 4 - - �6,000 -
ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION� Bushing Assembly 6 Shackle Side Bar 9 Hex. Head Locking Nut �� Collar
3 Pin 7 Flat Washer �0 Grease Fitting
5 Shim Washer 8 Hex. Head Cap Screw �� Lock Washer
8
Front of Truck
Front of Truck
fRonT and ReaR Bushing KiTs (sTandaRd paRTs)
REAR KIT WITH THREADED SIDE BARS
REAR KIT WITH THREADED BUSHING
8��
7
6
7
9
�
53
8��
6
97
5
�07
87
67
9
5
�(Ribbed or Threaded)
53
87
6
97
�0
Figure 2
Figure 3
ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION� Bushing Assembly 6 Shackle Side Bar 9 Hex. Head Locking Nut �� Collar
3 Pin 7 Flat Washer �0 Grease Fitting
5 Shim Washer 8 Hex. Head Cap Screw �� Lock Washer
9
Front of Truck
Front of Truck
fRonT and ReaR Bushing KiTs (sTandaRd paRTs)
REAR KIT WITH STANDARD SIDE BARS(smooTh Bushing in hangeR BRaCKeT)
FRONT KIT ON BRACKET WITH LOCKING CAPS
87
67
9
5
�
53
87
6
97
�0
�
3
5
5
Figure 4
Figure 5
ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION� Bushing Assembly 6 Shackle Side Bar 9 Hex. Head Locking Nut �� Collar
3 Pin 7 Flat Washer �0 Grease Fitting
5 Shim Washer 8 Hex. Head Cap Screw �� Lock Washer
�0
Front of Truck
Front of Truck
NOTE: Spread on Yoke Fork must be 4.�5” (new design) in order to install the Horton roller bushing. Retrofit kits are available through Peterbilt to update to current design.
�3-�3�97 Set-forward axle�3-�3�98 Set-backward axle
Install Collar (Item ��) with hole end toward spring.
fRonT and ReaR Bushing KiTs (sTandaRd paRTs)
FRONT KIT ON BRACKET WITH STEP PIN AND COLLAR
PETERBILT AIR RIDE PIN AND BUSHING KIT
7
7
8
��
9
3(Step Pin)
�0
5
�
5
8
�
76
��
9
�
�
3 5
�0��
(Step Pin)
�0
Figure 6
Figure 7
ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION ITEM DESCRIPTION� Bushing Assembly 6 Shackle Side Bar 9 Hex. Head Locking Nut �� Collar
3 Pin 7 Flat Washer �0 Grease Fitting
5 Shim Washer 8 Hex. Head Cap Screw �� Lock Washer
��
paRTs and RepaiR KiTs (fRonT anChoR pin and ReaR shaCKle)PART PIN & BUSHING (QTY 1) SIDE BAR WASHER DRIVE COMMENTSNUMBER SPRING EYE HANGER (QTY 1) KIT TOOL
994400 994454 99454� �3878 994476 994563
994401 994453 994540 �3878 994476 994563
994403 994456 994455 �3984 See Comment See Comment Washer Kit: 994478 Hanger, 994476 Eye;
Pin and Bushing 994455 is threaded;
Drive Tool: 994441 Hanger, 994563 Eye
994404 994454 99454� �3890 994476 994563
994405 994456 994455 �3995 See Comment See Comment Washer Kit: 994478 Hanger, 994476 Eye;
Pin and Bushing 994455 is threaded;
Drive Tool: 994441 Hanger, 994563 Eye
994406 994450 99454� �3890 994476 994563
994407 994450 994537 �3890 994476 994563
994408 994453 994540 �3890 994476 994563
994409 994453 994536 �3890 994476 994563
994410 994453 994536 �3893 994476 994563
994411 994449 994536 �3890 994476 994563
994415 99445� 994550 �3934 994476 994563
994416 994453 994540 �4046 994476 994563
994417 994463 994544 �3943 See Comment 994564 994480 Sleeve/Bushing, 994477 Shaft/Pin
994418 994463 994555 �3945 See Comment See Comment Washer Kit: 994476 Hanger, 994477 Eye;
Drive Tool: 994563 Hanger, 994564 Eye
994419 99446� 994558 �3945 See Comment See Comment Washer Kit: 994476 Hanger, 994477 Eye;
Drive Tool: 994563 Hanger, 994564 Eye
994420 994459 994543 �3878 994476 994563
994421 994458 99454� �3878 994476 994563
994424 994463 994544 �395� 994477 994564
994425 99445� 994538 �389� 994476 994563
994426 994466 994546 �3965 994476 994563
994427 994466 994546 �4�75 994476 994563
994428 994457 994554 �389� 994476 994563
994429 994465 994559 �389� 994476 994563
994431 994456 994455 �3985 See Comment See Comment Washer Kit: 994478 Hanger, 994476 Eye;
Pin and Bushing 994455 is threaded
Drive Tool: 994441 Hanger, 994563 Eye
994433 994448 99456� �3987 994478 994565
994434 99449� - - 994476 994563
994438 994484 994484 �4030 994478 994565
994439 994484 994484 �403� 994478 994565
994471 994490 - - 994476 994563
994472 994463 994544 �4�34 994477 994564
994473 994484 994484 �4�35 994478 994565
994474 99449� 994540 �4�49 994476 994563
994475 994453 994540 �3893 994476 994563
994481 99448� 99457� �389� 994476 994563
994483 994453 994548 �3978 994476 994563
994485 99449� 99454� �3890 See Comment 994563 994476 Hanger, 994477 Eye
994486 994493 - - 994476 994563
994487 994494 - - 994476 994563
��
paRTs and RepaiR KiTs (fRonT anChoR pin and ReaR shaCKle)PART PIN & BUSHING (QTY 1) SIDE BAR WASHER DRIVE COMMENTSNUMBER SPRING EYE HANGER (QTY 1) KIT TOOL994488 994495 - - 994476 994563
994489 994496 - - 994476 994563
994500 994466 994546 13966 (threaded) 994476 994563 Also has side bar 14275 (thru hole).
994501 994452 994540 13891 994476 994563
994502 994456 994551 13891 994476 994563
994503 994506 994506 13943 994477 994564
994507 994508 994508 14710 994476 994563
994509 See Comment - - - 994566 Heavy Duty Suspension Pin and Bushing: 994510
Rear Spring Eye; 994509 Front Anchor Spring Eye.
Reuse Ford H Bracket.
994510 See Comment - - - 994566 Heavy Duty Suspension Pin and Bushing: 994510
Rear Spring Eye; 994510 Front Anchor Spring Eye.
Reuse Ford H Bracket.
994511 994455 994455 14135 994478 994441 Pin and Bushing 994455 is threaded.
994441 Hanger, 994563 Eye.
994512 994515 - - 994476 994563
994513 994516 994572 13891 994476 994563
994514 994523 994590 13878 994476 994563
994519 994484 994484 14594 994478 994565
994520 994522 994544 13943 See Comment 994564 994480 Sleeve/Bushing, 994477 Shaft/Pin
994524 994527 994547 15325 994526 994563
994528 - 994539 - - 994566 Reuse Ford H Bracket
994529 - 994539 - - 994566 Reuse Ford H Bracket
994533 994453 994453 15402 994476 994563
994534 994453 994540 13891 994476 994563
994567 - 994539 - - 994566 Reuse Ford H Bracket
994570 994569 - - - 994566 Reuse Kenworth Side Bars
994586 994454 - - 994476 994563
994587 994454 994554 13891 994476 994563
994588 994589 - - 994476 994563 Master Kit
994591 - - - - - Master Drive Tool Kit
994593 994604 994540 13995 See Comment See Comment Washer Kit: 994476 Hanger, 994478 Eye;
Drive Tool: 994563 Hanger, 994565 Eye
994596 994600 994550 13878 994526 994563 Reuse Ford H Bracket.
994597 - 994608 - - 994566 Reuse Ford H Bracket.
994599 994463 994544 16834 994477 994564 Reuse Ford H Bracket.
994601 994560 994540 17107 994476 994563
994603 994453 994541 - 994476 994563
994605 994460 994555 13891 994526 994563
994606 994448 994540 17549 See Comment See Comment Washer Kit: 994476 Hanger, 994478 Eye;
Drive Tool: 994563 Hanger, 994565 Eye
994607 994456 994455 17548 See Comment See Comment Washer Kit: 994478 Hanger, 994476 Eye;
Pin & Bushing 994455 is threaded
Drive Tool: 994441 Hanger, 994563 Eye
994610 994452 994540 13890 994476 994563
994611 994452 994540 13878 994476 994563
994612 994466 994546 16000 (threaded) 994476 994563 Also has side bar 14275 (thru hole).
994613 994453 994540 15402 994476 994563
994968 994460 994460 13891 994526 994563
© 2012 Horton Holding, Inc. All rights reserved.Form # 22259-S-0312
*ISO/TS 16949, ISO 14001 and ISO 9001 Certified**ISO 14001 and ISO 9001 Certified
www.hortonww.com
Offices
USAMinnesota, USA**South Dakota, USA*Indiana, USA*+1 (651) 361-64001 (800) [email protected]
CanadaQuebec, Canada+1 (514) [email protected]
MexicoEdo. Méx., México+52 (55) [email protected]
EuropeSchweinfurt, Germany*+49-(0)[email protected]
Representatives
BrazilNip-Rep Representações ComerciaisEm Autopeças LtdaSão Paulo, Brazil+55 (11) [email protected]
ChilePablo CasanuevaLos Vilos, Chile+ 56 [email protected]
RussiaPskov, Russia+7 911 362 25 [email protected]
KoreaHIOIL E and T Co., Ltd.Seoul, Korea+82 2 413 [email protected]
P.R. ChinaR&S Promotion Co., Ltd.West Beijing, P.R. [email protected]
IndiaExcel Polymotive Mumbai, India+91 [email protected]
AustraliaNorman G. Clark Pty, Ltd (licensee)Victoria, [email protected]