rotamass ti coriolis mass flow specifications - … · rotamass nano measuring principle and flow...

68
General Specifications Rotamass TI Coriolis Mass flow meter GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18 Scope of application Precise flow rate measurement of fluids and gases, multi-phase media and media with specific gas content using the Coriolis principle. Direct measurement of mass flow and density in- dependent of the medium's physical properties, such as density, viscosity and homogeneity Medium temperatures of -50...260 °C Process pressures up to 285 bar EN, ASME, JPI or JIS standard flange process connections up to three nominal diameters per meter size, thread Connection to common process control systems, such as via HART7 Hazardous area approvals: IECEx, ATEX Safety-related applications: PED according to AD 2000, SIL 2, secondary containment up to 65 bar Advantages and benefits Inline measurement of several process variables, such as mass, density and temperature Adapterless installation due to multi-size flange concept No straight pipe runs at inlet or outlet required Fast and uncomplicated commissioning and oper- ation of the flow meter Maintenance-free operation Functions that can be activated subsequently (fea- ture on demand) Total health check: Self-monitoring of the entire flow meter, including accuracy Maximum accuracy because the calibration labo- ratory is accredited by DAkkS (for option /K5) Self-draining installation Rotamass Nano

Upload: lydat

Post on 30-Jul-2018

224 views

Category:

Documents


0 download

TRANSCRIPT

GeneralSpecifications

Rotamass TI Coriolis Mass flowmeter

GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Scope of application Precise flow rate measurement of fluids and

gases, multi-phase media and media with specificgas content using the Coriolis principle.

Direct measurement of mass flow and density in-dependent of the medium's physical properties,such as density, viscosity and homogeneity

Medium temperatures of -50...260 °C

Process pressures up to 285 bar

EN, ASME, JPI or JIS standard flange processconnections up to three nominal diameters permeter size, thread

Connection to common process control systems,such as via HART7

Hazardous area approvals: IECEx, ATEX

Safety-related applications: PED according to AD2000, SIL 2, secondary containment up to 65 bar

Advantages and benefits Inline measurement of several process variables,

such as mass, density and temperature

Adapterless installation due to multi-size flangeconcept

No straight pipe runs at inlet or outlet required

Fast and uncomplicated commissioning and oper-ation of the flow meter

Maintenance-free operation

Functions that can be activated subsequently (fea-ture on demand)

Total health check: Self-monitoring of the entireflow meter, including accuracy

Maximum accuracy because the calibration labo-ratory is accredited by DAkkS (for option /K5)

Self-draining installation

Rotamass Nano

Table of contents

2 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Table of contents1 Introduction..................................................................................................................................................... 4

1.1 Applicable documents............................................................................................................................... 41.2 Product overview ...................................................................................................................................... 5

2 Measuring principle and flow meter ............................................................................................................. 62.1 Measuring principle................................................................................................................................... 62.2 Flow meter ................................................................................................................................................ 8

3 Application and measuring ranges............................................................................................................. 103.1 Measured quantity .................................................................................................................................. 103.2 Measuring range overview...................................................................................................................... 103.3 Mass flow................................................................................................................................................ 113.4 Volume flow ............................................................................................................................................ 113.5 Pressure loss .......................................................................................................................................... 113.6 Density.................................................................................................................................................... 123.7 Temperature ........................................................................................................................................... 12

4 Accuracy ....................................................................................................................................................... 134.1 Overview................................................................................................................................................. 134.2 Zero point stability of the mass flow........................................................................................................ 144.3 Mass flow accuracy ................................................................................................................................ 14

4.3.1 Sample calculation for liquids ................................................................................................. 154.3.2 Sample calculation for gases .................................................................................................. 16

4.4 Accuracy of density................................................................................................................................. 174.4.1 For liquids ............................................................................................................................... 174.4.2 For gases ................................................................................................................................ 17

4.5 Accuracy of mass flow and density according to MS code..................................................................... 184.5.1 For liquids ............................................................................................................................... 184.5.2 For gases ................................................................................................................................ 18

4.6 Volume flow accuracy............................................................................................................................. 194.6.1 For liquids ............................................................................................................................... 194.6.2 For gases ................................................................................................................................ 19

4.7 Accuracy of temperature......................................................................................................................... 204.8 Repeatability ........................................................................................................................................... 214.9 Calibration conditions ............................................................................................................................. 21

4.9.1 Mass flow calibration and density adjustment......................................................................... 214.9.2 Density calibration................................................................................................................... 21

5 Operating conditions ................................................................................................................................... 225.1 Location and position of installation........................................................................................................ 22

5.1.1 Sensor installation position ..................................................................................................... 225.2 Installation instructions ........................................................................................................................... 245.3 Process conditions.................................................................................................................................. 24

5.3.1 Medium temperature range..................................................................................................... 245.3.2 Density .................................................................................................................................... 245.3.3 Pressure.................................................................................................................................. 255.3.4 Effect of temperature on accuracy .......................................................................................... 275.3.5 Insulation and heat tracing...................................................................................................... 28

Table of contents

GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18 3 / 68

5.4 Ambient conditions ................................................................................................................................. 295.4.1 Allowed ambient temperature for sensor ................................................................................ 305.4.2 Temperature specification by temperature classes ................................................................ 31

6 Mechanical specification ............................................................................................................................. 326.1 Design..................................................................................................................................................... 326.2 Material ................................................................................................................................................... 33

6.2.1 Material wetted parts............................................................................................................... 336.2.2 Non-wetted parts..................................................................................................................... 33

6.3 Process connections, dimensions and weights of sensor ...................................................................... 346.3.1 Process connections and overall length L1 ............................................................................ 35

6.4 Transmitter dimensions .......................................................................................................................... 42

7 Transmitter specification............................................................................................................................. 437.1 Inputs and outputs .................................................................................................................................. 44

7.1.1 Output signals ......................................................................................................................... 457.1.2 Input signals............................................................................................................................ 51

7.2 Power supply .......................................................................................................................................... 527.3 Cable specification.................................................................................................................................. 52

8 Approvals and declarations of conformity ................................................................................................ 53

9 Ordering information.................................................................................................................................... 549.1 MS code.................................................................................................................................................. 54

9.1.1 Transmitter .............................................................................................................................. 549.1.2 Sensor..................................................................................................................................... 549.1.3 Meter size ............................................................................................................................... 559.1.4 Material wetted parts............................................................................................................... 559.1.5 Process connection size ......................................................................................................... 559.1.6 Process connection type......................................................................................................... 569.1.7 Sensor housing material ......................................................................................................... 569.1.8 Medium temperature range..................................................................................................... 579.1.9 Mass flow and density accuracy ............................................................................................. 579.1.10 Design and housing ................................................................................................................ 589.1.11 Ex approval ............................................................................................................................. 589.1.12 Cable entries........................................................................................................................... 599.1.13 Inputs and outputs .................................................................................................................. 599.1.14 Display .................................................................................................................................... 60

9.2 Options ................................................................................................................................................... 619.2.1 Connecting cable length ......................................................................................................... 619.2.2 Additional nameplate information............................................................................................ 619.2.3 Presetting of customer parameters......................................................................................... 629.2.4 Concentration measurement................................................................................................... 629.2.5 Insulation and heat tracing...................................................................................................... 649.2.6 Certificates .............................................................................................................................. 649.2.7 Tube health check................................................................................................................... 669.2.8 Fixing device ........................................................................................................................... 669.2.9 Measurement of heat quantity ................................................................................................ 669.2.10 Customer specific special product manufacture ..................................................................... 66

Rotamass NanoIntroduction Applicable documents

4 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

1 Introduction

1.1 Applicable documents

The following documents supplement these General Specifications: Ex instruction manual ATEX IM 01U10X01-00-R Ex instruction manual IECEx IM 01U10X02-00-R

Product overview

Rotamass NanoIntroduction

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 5 / 68

1.2 Product overview

Rotamass Coriolis flow meters are available in various product families distinguished bytheir applications. Each product family includes several product alternatives and addi-tional device options that can be selected.

The following overview serves as a guide for selecting products.Overview ofRotamass productfamilies

Rotamass Nano

For low flow rate applicationsFive meter sizes Nano 06, Nano 08, Nano 10, Nano 15,Nano 20 with the following connection sizes:

DN15, DN25, DN40 1/4", 1/2", 3/8", 3/4", 1", 1 1/2"

Maximum mass flow up to 1.5 t/h

Rotamass Prime

Versatility with low costs for the operatorFour meter sizes Prime 25, Prime 40, Prime 50, Prime 80with the following connection sizes:

DN15, DN25, DN40, DN50, DN80 3/8", 1/2", 3/4", 1", 1 1/2", 2", 2 1/2", 3"

Maximum mass flow up to 76 t/h

Rotamass Supreme

Excellent performance under demanding conditionsFour meter sizes Supreme 34, Supreme 36, Supreme 38,Supreme 39 with the following connection sizes:

DN15, DN25, DN40, DN50, DN80, DN100, DN125 3/8", 1/2", 3/4", 1", 1 1/2", 2", 2 1/2", 3", 4", 5"

Maximum mass flow up to 170 t/h

Rotamass Intense

For high process pressure applicationsThree meter sizes Intense 34, Intense 36, Intense 38 withthe following connection sizes:

1/2", 1", 2"Maximum mass flow up to 50 t/h

Rotamass Hygienic

For food, beverage and pharmaceutical applicationsFour meter sizes Hygienic 25, Hygienic 40, Hygienic 50,Hygienic 80 with the following connection sizes:

DN25, DN40, DN50, DN65, DN80 1", 1 1/2", 2", 2 1/2", 3"

Maximum mass flow up to 76 t/h

Rotamass Giga

For high flow rate applicationsTwo meter sizes Giga 1F, Giga 2H with the followingconnection sizes:

DN100, DN125, DN150, DN200 4", 5", 6", 8"

Maximum mass flow up to 600 t/h

Rotamass NanoMeasuring principle and flow meter Measuring principle

6 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

2 Measuring principle and flow meter

2.1 Measuring principle

The measuring principle is based on the generation of Coriolis forces. For this purpose, adriver system (E) excites the two measuring tubes (M1, M2) in their first resonance fre-quency. Both pipes vibrate inversely phased, similar to a resonating tuning fork.

A

E

F1

S1

S2

F2

M1

Q

M2

-F1

-F2-A

inlet

outlet

Fig. 1: Coriolis principle

M1,M2 Measuring tubes E Driver systemS1, S2 Pick-offs A Direction of measuring tube vibrationF1, F2 Coriolis forces Q Direction of medium flow

Mass flow The medium flow through the vibrating measuring tubes generates Coriolis forces (F1, -F1 and F2, -F2) that produce positive or negative values for the tubes on the inflow oroutflow side. These forces are directly proportional to the mass flow and result in defor-mation (torsion) of the measuring tubes.

1

3

1

2

3AE

AE

F1

F2

α

Fig. 2: Coriolis forces and measuring tube deformation

1 Measuring tube mount AE Rotational axis2 Medium F1, F2 Coriolis forces3 Measuring tube α Torsion angle

Measuring principle

Rotamass NanoMeasuring principle and flow meter

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 7 / 68

The small deformation overlying the fundamental vibration is recorded by means of pick-offs (S1, S2) attached at suitable measuring tube locations. The resulting phase shift Δφbetween the output signals of pick-offs S1 and S2 is proportional to the mass flow. Theoutput signals generated are further processed in a transmitter.

Δφ

S1

S2

y

t

Fig. 3: Phase shift between output signals of S1 and S2 pick-offs

Δφ ~ FC ~

dt

dm

Δφ Phase shiftm Dynamic masst Timedm/dt Mass flow

Densitymeasurement

Using a driver and an electronic regulator, the measuring tubes are operated in their res-onance frequency ƒ. This resonance frequency is a function of measuring tube geometry,material properties and the mass of the medium covibrating in the measuring tubes. Alter-ing the density and the attendant mass will alter the resonance frequency. The transmittermeasures the resonance frequency and calculates density from it according to the for-mula below. Device-dependent constants are determined individually during calibration.

A

t

ƒ2

ƒ1

Fig. 4: Resonance frequency of measuring tubes

A Measuring tube displacementƒ1 Resonance frequency with medium 1ƒ2 Resonance frequency with medium 2

ρ = + ß ƒ2

α

ρ Medium densityƒ Resonance frequency of measuring tubesα, β Device-dependent constants

Temperaturemeasurement

The measuring tube temperature is measured in order to compensate for the effects oftemperature on the flow meter. This temperature approximately equals the medium tem-perature and is made available as a measured quantity at the transmitter as well.

Rotamass NanoMeasuring principle and flow meter Flow meter

8 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

2.2 Flow meter

The Rotamass Coriolis flow meter consists of: Sensor Transmitter

Sensor and transmitter are linked via connecting cable. As a result, sensor and transmit-ter can be installed in different locations.

3

2

2

4

1

5

Fig. 5: Configuration of Rotamass remote type

1 Sensor 4 Connecting cable2 Process connections 5 Transmitter3 Sensor terminal box

Generalspecifications

All available properties of the Rotamass Coriolis flow meter are specified by means of amodel code (MS code).

One MS code position may include several characters depicted by means of dashedlines.

The positions of the MS code relevant for the respective properties are depicted andhighlighted in blue. Any values that might occupy these MS code positions are subse-quently explained.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Fig. 6: Highlighted MS code positions

E N 20 15K TT9 0 0 C3 A NN00 2 JB 1 SE- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Fig. 7: Example of a completed MS code

A complete description of the MS code is included in the chapter entitled Ordering infor-mation [ 54].

Flow meter

Rotamass NanoMeasuring principle and flow meter

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 9 / 68

Type of design Position 10 of the MS code defines whether the remote type is used. It specifies furtherflow meter properties, such as the transmitter coating, see Design and housing [ 58]

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Flow meter MS codePosition 10

Remote type

A, B, E, F

Transmitter overview Two different transmitters are available that differ in their functional scope.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Transmitter Properties MS codePosition 1

Essential Down to 0.15 % mass flow accuracy of liquids Down to 0.75 % mass flow accuracy of gases Down to 4 g/l accuracy of density Diagnostic functions HART communication Data backup on microSD card

E

Ultimate Down to 0.1 % mass flow accuracy of liquids Down to 0.5 % mass flow accuracy of gases Down to 0.5 g/l accuracy of density Diagnostic functions HART communication Special functions for special applications, such

as dynamic pressure compensation Data backup on microSD card

U

Rotamass NanoApplication and measuring ranges Measured quantity

10 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

3 Application and measuring ranges

3.1 Measured quantity

The Rotamass Coriolis flow meter can be used to measure the following media: Liquids Gases Mixtures, such as emulsions, suspensions, slurries

Possible limitations applying to measurement of mixtures must be checked with the re-sponsible Yokogawa sales organization.

The following variables can be measured using the Rotamass: Mass flow Density Temperature

Based on these measured quantities, the transmitter also calculates: Volume flow Partial component concentration of a two-component mixture Partial component flow rate of a mixture consisting of two components (net flow)

In this process, the net flow is calculated based on the known partial componentconcentration and the overall flow.

3.2 Measuring range overview

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20Mass flow range

Typicalconnection size DN15/ ½" DN15/ ½" DN15/ ½" DN15/ ½" DN15/ ½"

[ 11]Qnom 0.021 t/h 0.045 t/h 0.17 t/h 0.37 t/h 0.95 t/hQmax 0.04 t/h 0.094 t/h 0.3 t/h 0.6 t/h 1.5 t/h

Maximum volume flow(Water) 0.04 m3/h 0.094 m3/h 0.3 m3/h 0.6 m3/h 1.5 m3/h [ 11]

Range of medium density0...5 kg/l [ 12]

Medium temperature rangeStandard1) -50...150 °C

[ 24]Mid-range -50...260 °C

1) May vary depending on the design.

Qnom - Nominal mass flow

Qmax - Maximum mass flow

The nominal mass flow Qnom is used as a characteristic for improved comparability.

Mass flow

Rotamass NanoApplication and measuring ranges

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 11 / 68

3.3 Mass flow

The nominal mass flow Qnom is defined as the mass flow of water (temperature: 20 °C) at1 bar pressure loss along the flow meter.

For Rotamass Nano the following meter sizes to be determined using the MS code[ 54] are available.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

N

Mass flow of liquids Sensor andmeter size

Typicalconnection size

Qnom

in t/hQmax

in t/hMS codePosition 3

Nano 06 DN15/ ½" 0.021 0.04 6Nano 08 DN15/ ½" 0.045 0.094 8Nano 10 DN15/ ½" 0.17 0.3 10Nano 15 DN15/ ½" 0.37 0.6 15Nano 20 DN15/ ½" 0.95 1.5 20

Mass flow of gases When using the Rotamass for measuring the flow of gases, the mass flow is usually lim-ited by the pressure loss generated and the maximum flow velocity. Since these dependheavily on the application, it is strongly recommended that the Yokogawa FlowConfigura-tor software be used or the responsible Yokogawa sales organization be contacted whendesigning the size of the device.

3.4 Volume flow

Volume flow ofliquids (water at 20 °C)

Sensor andmeter size

Volume flow(at 1 bar pressure loss)

in m3/h

Maximum volume flowin m3/h

Nano 06 0.021 0.04Nano 08 0.045 0.094Nano 10 0.17 0.3Nano 15 0.37 0.6Nano 20 0.95 1.5

Volume flow ofgases

When using the Rotamass for measuring the flow of gases, the flow rate is usually limitedby the pressure loss generated and the maximum flow velocity. Since these dependheavily on the application, it is strongly recommended that the Yokogawa FlowConfigura-tor software be used or the responsible Yokogawa sales organization be contacted whendesigning the size of the device.

3.5 Pressure loss

The pressure loss along the flow meter is heavily dependent on the application. The pres-sure loss of 1 bar at nominal mass flow Qnom also applies to water and is considered thereference value. Use of the Yokogawa FlowConfigurator software is recommended forachieving an accurate design.

Rotamass NanoApplication and measuring ranges Density

12 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

3.6 Density

Meter size Measuring range of densityNano 06

0...5 kg/lNano 08Nano 10Nano 15Nano 20

Rather than being measured directly, density of gas is usually calculated using its refer-ence density, process temperature and process pressure.

3.7 Temperature

The temperature measuring range is limited by the allowed process temperature, seeMedium temperature range [ 24].

Maximum measuring range: -50...260 °C

Overview

Rotamass NanoAccuracy

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 13 / 68

4 Accuracy

In this chapter, maximum deviations are indicated as amounts. The actual values maydeviate from the measured values by exceeding them or falling below.

4.1 Overview

Achievableaccuracies forliquids

The value Dflat specified for accuracy of mass flow applies for flow rates exceeding themass flow limit Qflat. If the mass flow is less, it is necessary to also consider zero point sta-bility Z, see Zero point stability of the mass flow [ 14].

The following values are achieved at calibration conditions when the device is delivered,see Calibration conditions [ 21]. For small meter sizes, specifications may not be as ac-curate, see Mass flow and density accuracy [ 57].

Measured quantity Accuracy fortransmitters

Essential Ultimate

Mass flow1)

Maximum deviation Dflat

Down to 0.2 %of measuredvalue

Down to 0.1 %of measuredvalue

RepeatabilityDown to 0.1 %of measuredvalue

Down to 0.05 %of measuredvalue

Volume flow(water)1)

Maximum deviation DV

Down to 0.45 %of measuredvalue

Down to 0.12 %of measuredvalue

RepeatabilityDown to 0.23 %of measuredvalue

Down to 0.06 %of measuredvalue

DensityMaximum deviation Down to 4 g/l Down to 0.5 g/lRepeatability Down to 2 g/l Down to 0.3 g/l

Temperature Maximum deviation Down to 0.5 °C Down to 0.5 °C1) Based on the measured values of the pulse output. Includes the combined effects of re-peatability, linearity and hysteresis.

Achievableaccuracies for gases

Measured quantity Accuracy fortransmitters

Essential Ultimate

Mass flow /standard volumeflow1)

Maximum deviation Dflat

Down to 0.75 %of measuredvalue

Down to 0.5 %of measuredvalue

RepeatabilityDown to 0.6 %of measuredvalue

Down to 0.4 %of measuredvalue

Temperature Maximum deviation Down to 0.5 °C Down to 0.5 °C1) Based on the measured values of the pulse output. Includes the combined effects of re-peatability, linearity and hysteresis.

In the event of medium temperature jumps, a delay is to be expected in the temperaturebeing displayed due to low heat capacity and heat conductivity of gases.

The connecting cable impacts the accuracy. The values specified are valid for connectingcables < 30 m long.

Rotamass NanoAccuracy

Zero point stability of the massflow

14 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

4.2 Zero point stability of the mass flow

The values Dflat specified for accuracy of mass flow apply for flow rates exceeding themass flow limit Qflat. If the mass flow is less, it is necessary to also consider zero point sta-bility Z (see chapter Mass flow accuracy [ 14]).

Meter size Zero point stability Zin kg/h

Nano 06 0.003Nano 08 0.005Nano 10 0.0085Nano 15 0.019Nano 20 0.048

4.3 Mass flow accuracy

Above mass flow Qflat, maximum deviation is constant and referred to as Dflat. It dependson the product version selected and can be found in the tables in chapter Accuracy ofmass flow and density according to MS code [ 18].

Taking zero point stability into consideration, the following calculation formulas are to beused for maximum deviation D:

D =

D =

Dflat

× 100 % Z × k

QQ < Q

flat

Z × k

Dflat

Q ≥ Qflat

= × 100 %

D Maximum deviation in % Qflat Mass flow above which Dflat appliesDflat Maximum deviation for high flow rates Z Zero point stabilityQ Mass flow in kg/h k Constant

Meter size kNano 06 1.4Nano 08 1.1Nano 10 2Nano 15 2Nano 20 2

Mass flow accuracy

Rotamass NanoAccuracy

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 15 / 68

4.3.1 Sample calculation for liquids

Accuracy usingwater at 20 °C as an example

0

0.1

0.2

0.3

0.4

0 0.2 0.4 0.6 0.8 1.0

0.5

Qflat

Q

D

Qnom

%

Fig. 8: Effect of zero point stability on maximum deviation (schematic)

D Maximum deviation Q Mass flowQnom Nominal mass flow Qflat Mass flow above which Dflat applies

Turn down Qminimal:Qnom

Maximum deviation D Water pressure loss

1:100 1.0 % ≈ 0 mbar1:40 0.4 % 0.7 mbar1:10 0.1 % 10 mbar1:2 0.1 % 250 mbar1:1 0.1 % 1000 mbar

Example:E N 20 15K TT9 0 0 C3 NN00 2 JB 1 SE- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

A

Medium: LiquidZero point stability Z: 0.048 kg/hFactor k 2Maximum deviation Dflat: 0.1 %Value of mass flow Q: 25 kg/h

Calculation of flow rate condition:

Check whether

Z × k

Dflat

Q ≥ Qflat

= × 100 %

Qflat = Z × k / Dflat × 100 % = 0.048 kg/h × 2 / 0.1 % × 100 % = 96 kg/hQ = 25 kg/h < Qflat = 96 kg/h, as a result, accuracy is calculated using the following for-mula:

D = × 100 % Z × k

Q

Calculation of accuracy:D = 0.048 kg/h × 2 / 25 kg/h × 100 %

D = 0.384 %

Rotamass NanoAccuracy Mass flow accuracy

16 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

4.3.2 Sample calculation for gasesThe maximum deviation in the case of gases depends on the product version selected,see also Mass flow and density accuracy [ 57].

Example: Medium: GasZero point stability Z: 0.048 kg/hFactor k 2Maximum deviation Dflat: 0.5 %Value of mass flow Q: 10 kg/h

Calculation of flow rate condition:

Check whether

Z × k

Dflat

Q ≥ Qflat

= × 100 %

Qflat = Z × k / Dflat × 100 % = 0.048 kg/h × 2 / 0.5 % × 100 % = 192 kg/h

Q = 10 kg/h < Qflat = 192 kg/h, as a result, accuracy is calculated using the following for-mula:

D = × 100 % Z × k

Q

Calculation of accuracy:D = 0.048 kg/h × 2 / 10 kg/h × 100 %

D = 0.96 %

Since the mass flow of gas measurements is low, use of the Yokogawa FlowConfiguratorsoftware is recommended for designing the suitable product and contacting the responsi-ble Yokogawa sales office for this purpose.

Accuracy of density

Rotamass NanoAccuracy

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 17 / 68

4.4 Accuracy of density

4.4.1 For liquids

Meter size Transmitter Maximum deviation of density1)

in g/lNano 06

Essential Down to 4Nano 08Nano 10Nano 15Nano 20Nano 06

Ultimate Down to 0.5Nano 08Nano 10Nano 15Nano 20

1) Deviations possible depending on product version (meter size, type of calibration)

The maximum deviation depends on the product version selected, see also Accuracy ofmass flow and density according to MS code [ 18].

4.4.2 For gasesIn most applications, density at standard conditions is entered into the flow meter andused to calculate the standard volume flow based on mass flow.

If gas pressure is a known value, after entering a reference density, the transmitter is ableto calculate gas density from temperature and pressure as well (while assuming an idealgas).

Alternatively, there is an option for measuring gas density. In order to do so, it is neces-sary to adapt the lower density limit value in the transmitter. Additional information can befound in the related software instruction manual.

For most applications the direct measurement of the gas density will have insufficient ac-curacy (see chapter Accuracy of mass flow and density according to MS code [ 18]).

Rotamass NanoAccuracy

Accuracy of mass flow and densityaccording to MS code

18 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

4.5 Accuracy of mass flow and density according to MS code

Accuracy for flow rate as well as density is selected via MS code position 9. Here a dis-tinction is made between devices for measuring liquids and devices for measuring gases.No accuracy for density measurement is specified for gas measurement devices.

4.5.1 For liquids

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Essential MS codePosition 9

Maximumdeviationof density

1)

in g/l

Applicablemeasuring

range of ac-curacyin kg/l

Maximum deviation Dflat for mass flowin %

Nano 06 Nano 08 Nano 10 Nano 15 Nano20

E9 20 0.3...5 0.2 – – – –E8 8 0.3...5 – 0.2 – – –E7 4 0.3...5 – – 0.2 0.2 0.2

1) Specified maximum deviation is achieved within the applicable measuring range fordensity.

Ultimate MS codePosition 9

Maximumdeviationof density

1)

in g/l

Applicablemeasuringrange ofaccuracy

in kg/l

Maximum deviation Dflat for mass flowin %

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20

D9 20 0.3...5 0.15 – – – –D8 8 0.3...5 – 0.15 – – –D7 4 0.3...5 – – 0.15 0.15 0.15D3 1 0.3...5 – – 0.15 0.15 0.15D2 0.5 0.3...2.5 – – – 0.15 0.15C8 8 0.3...5 – 0.1 – – –C7 4 0.3...5 – – 0.1 0.1 0.1C3 1 0.3...5 – – 0.1 0.1 0.1C2 0.5 0.3...2.5 – – – 0.1 0.1

1) Specified maximum deviation is achieved within the applicable measuring range fordensity.

4.5.2 For gases

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Essential Maximum deviation Dflat of mass flowin %

MS codePosition 9

0.75 70

Ultimate Maximum deviation Dflat of mass flowin %

MS codePosition 9

0.5 50

Volume flow accuracy

Rotamass NanoAccuracy

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 19 / 68

4.6 Volume flow accuracy

4.6.1 For liquidsThe following formula can be used to calculate the accuracy of liquid volume flow:

DV = D2 + × 100%

∆ρρ( )

2

DV Maximum deviation of volume flow D Maximum deviation of mass flow in %Δρ Maximum deviation of density in kg/l ρ Density in kg/l

4.6.2 For gasesAccuracy of standard volume flow for gas with a fixed composition equals the maximumdeviation D of the mass flow.

DV = D

In order to determine the standard volume flow for gas, it is necessary to input areference density in the transmitter. Additional information can be found in the re-lated software instruction manual. The accuracy specified is achieved only forfixed gas composites. Major deviations may appear if the gas compositionchanges.

Rotamass NanoAccuracy Accuracy of temperature

20 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

4.7 Accuracy of temperature

Various medium temperature ranges are specified for Rotamass Nano: Standard:

– -50...150 °C Mid-range:

– -50...260 °C

Accuracy of temperature depends on the sensor temperature range selected (seeMedium temperature range [ 24]) and can be calculated as follows:

Formula for temperature specifications Standard and Mid-range

ΔT = 0.5 °C + 0.005 × |T - 20 °C|

ΔT Maximum deviation of temperatureT Temperature of medium

∆T

°C

0

0.5

1.0

1.5

2.0

-100 0 100 200 300

2.5

T

3.0

°C

Fig. 9: Presentation of temperature accuracy

Example:E N 20 15K TT9 0 0 C3 A NN00 2 JB 1 SE- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

The sample MS code specifies the Standard temperature range.

Temperature of medium T: 50 °C

Calculation of accuracy:ΔT = 0.5 °C + 0.005 × |50 °C - 20 °C|

ΔT = 0.65 °C

Repeatability

Rotamass NanoAccuracy

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 21 / 68

4.8 Repeatability

When using default damping times, the specified repeatability of mass flow, density andtemperature measurements equals half of the respective maximum deviation.

R = 2

D

R RepeatabilityD Maximum deviation

In deviation hereto, the following applies to mass and standard volume flow of gases:

R = 1.25

D

4.9 Calibration conditions

4.9.1 Mass flow calibration and density adjustmentAll Rotamass are calibrated in accordance with the state of the art at Rota Yokogawa.Optionally, the calibration can be performed according to a method accredited by DAkkSin accordance with DIN EN ISO/IEC 17025:2005 (Option K5, see Certificates [ 64]).

Each Rotamass device comes with a standard calibration certificate.

Calibration takes place at reference conditions. Specific values are listed in the standardcalibration certificate.

Reference conditionsMedium WaterDensity 0.9...1.1 kg/l

Medium temperature10...35 °CAverage temperature: 22.5 °C

Ambient temperature 10...35 °CProcess pressure (absolute) 1...2 bar

The accuracy specified is achieved at as-delivered calibration conditions stated.

4.9.2 Density calibrationDensity calibration is performed for maximum deviation of 0.5 g/l (MS code position 9 2).

Density calibration includes: Determination of calibration constants for medium densities at 0.7 kg/l, 1 kg/l and 1.65

kg/l at 20 °C medium temperature Determination of temperature compensation coefficients at 20...80 °C Check of results for medium densities at 0.7 kg/l, 1 kg/l and 1.65 kg/l at 20 °C medium

temperature Special configuration of the temperature sensor: Creation of density calibration certificate

Rotamass NanoOperating conditions

Location and position of installa-tion

22 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

5 Operating conditions

5.1 Location and position of installation

Rotamass Coriolis flow meters can be mounted horizontally, vertically and at an incline.The measuring tubes should be completely filled with the medium during this process asaccumulations of air or formation of gas bubbles in the measuring tube may result in er-rors in measurement. Straight pipe runs at inlet or outlet are usually not required.

Avoid the following installation locations and positions: Measuring tubes as highest point in piping when measuring liquids Measuring tubes as lowest point in piping when measuring gases Immediately in front of a free pipe outlet in a downpipe Lateral positions

Fig. 10: Installation position to be avoided: Flow meter in sideways position

5.1.1 Sensor installation positionSensor installationposition as afunction of themedium

Installation position Medium DescriptionHorizontal, measuring tubes atbottom

LiquidThe measuring tubes are orientedtoward the bottom. Accumulation ofgas bubbles is avoided.

Location and position of installa-tion

Rotamass NanoOperating conditions

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 23 / 68

Installation position Medium DescriptionHorizontal, measuring tubes at top

GasThe measuring tubes are orientedtoward the top. Accumulation of liquid,such as condensate is avoided.

Vertical, direction of flow towardsthe top

Liquid/gas

The sensor is installed on a pipe withthe direction of flow towards the top.Accumulation of gas bubbles or solidsis avoided. This position allows forcomplete self-draining of the measuringtubes.

Rotamass NanoOperating conditions Installation instructions

24 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

5.2 Installation instructions

The following instructions for installation must be observed:1. Protect the flow meter from direct sun irradiation in order to avoid exceeding the maxi-

mum allowed internal temperature of the transmitter.2. In case of installing two sensors of the same kind back-to-back redundantly, use a

customized design and contact the responsible Yokogawa sales organization.3. Avoid installation locations susceptible to cavitation, such as immediately behind a

control valve.4. In case that the medium temperatures deviate approx. 80 °C from the ambient tem-

perature, insulating the sensor is recommended if the goal is to maintain utmost accu-racy, see Insulation and heat tracing [ 28].

5. Avoid installation directly behind rotary and gear pumps to prevent fluctuations inpressure from interfering with the resonance frequency of the Rotamass measuringtubes.

5.3 Process conditions

5.3.1 Medium temperature range

The Rotamass specification for use in Ex areas is different, see Ex instructionmanual (IM 01U10X-00EN).

For Rotamass Nano the following medium temperature ranges are available:

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Temperature specification MS codePosition 8

Medium temperaturein °C

Standard 0 -50...150Mid-range 2 -50...260

5.3.2 Density

Meter size Measuring range of densityNano 06

0...5 kg/lNano 08Nano 10Nano 15Nano 20

Rather than being measured directly, density of gas is usually calculated using its refer-ence density, process temperature and process pressure.

Process conditions

Rotamass NanoOperating conditions

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 25 / 68

5.3.3 PressureThe maximum allowed process pressure depends on the medium temperature and theprocess connections selected.

Rule: The higher the temperature, the lower the allowed process pressure.

The following diagrams show the process pressure as a function of medium temperatureas well as the flange used (type and size of flange).

ASME class 150

JPI class 150

1

2

50

2

0

4

6

8

10

12

14

16

18

20

100 150 200 260

p in bar

T in °C-70 0 38

Fig. 11: Allowed process pressure as a function of process connection temperature

1 Flange suitable for ASME B16.5 class 1502 Flange suitable for JPI class 150

ASME class 300

EN PN40

JPI class 300 1

2

3

50

10

0

20

30

40

50

60

100 150 200 260 T in °C

p in bar

-70 0 38-50

Fig. 12: Allowed process pressure as a function of process connection temperature

1 Flange suitable for ASME B16.5 class 3002 Flange suitable for EN 1092-1 PN403 Flange suitable for JPI class 300

ASME class 600

JPI class 6001

2

50-50

20

0

40

60

80

100

100 150 200 260 T in °C

p in bar

-70 0 38

Fig. 13: Allowed process pressure as a function of process connection temperature

1 Flange suitable for ASME B16.5 class 6002 Flange suitable for JPI class 600

Rotamass NanoOperating conditions Process conditions

26 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

ASME class 900

EN PN100

1

2

50

20

0

40

60

80

100

120

140

160

100 150 200 260 T in °C

p in bar

-70 0 38-50

Fig. 14: Allowed process pressure as a function of process connection temperature

1 Flange suitable for ASME B16.5 class 9002 Flange suitable for EN 1092-1 PN100

ASME class 1500

50

50

0

100

150

200

250

300

100 150 200 260 T in °C

p in bar

-50 0 38

Fig. 15: Allowed process pressure as a function of process connection temperature, suitable forflange ASME B16.5 class 1500

JIS 10K

JIS 20K

-50 500

5

0

10

15

20

25

30

35

40

100 150 200 260 T in °C

p in bar

2

1

Fig. 16: Allowed process pressure as a function of process connection temperature

1 Flange suitable for JIS B 2220 10K2 Flange suitable for JIS B 2220 20K

Clamp connectionaccording to DIN 32676

-50-70 150500

10

0

20

30

40

50

60

100 200 T in °C

p in bar

Fig. 17: Allowed process pressure as a function of process connection temperature, suitable forprocess connection according to DIN 32676

Process conditions

Rotamass NanoOperating conditions

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 27 / 68

Tri- or Mini-Clamp

-50 0

10

0

20

30

40

50

60

50 100 150 T in °C

p in bar

Fig. 18: Allowed process pressure as a function of process connection temperature, suitable forprocess connection according to Tri- or Mini-Clamp

Process connectionswith internal thread

50-50 0

50

0

100

150

200

250

300

100 150 200 260 T in °C

p in bar

Fig. 19: Allowed process pressure as a function of temperature, suitable for process connectiontemperature, suitable for process connections with internal thread G and NPT

5.3.4 Effect of temperature on accuracyEffect of mediumtemperature

The specified accuracy of the density measurement (see Mass flow and density accuracy[ 57]) applies at calibration conditions and may deteriorate if medium temperatures de-viate from those conditions. The effect of temperature is minimal for the product versionwith MS code position 9, value 2.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

C2

In this case, the effect of temperature is calculated as follows:

D'ρ = 0.000015 kg/(l °C) × |T

pro - 20 °C|

D'ρ Additional density deviation due to the effect of medium temperature in kg/lT pro Medium temperature in °C

Rotamass NanoOperating conditions Process conditions

28 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

5.3.5 Insulation and heat tracing

In case that the medium temperature deviates more than 80°C from the ambienttemperature, insulating the sensor is recommended to avoid negative effectsfrom temperature fluctuations on accuracy.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

4

1

3

1

5

2

Fig. 20: Configuration of Rotamass with insulation and heat tracing

1 Heating system connections 4 Process connection2 Insulation 5 Ventilation3 Sensor terminal box

Overview of deviceoptions forinsulation and heattracing for remotetype

Description Options Insulation T10 Insulation Heat tracing without ventilation

T21, T22, T26

Insulation Heat tracing with ventilation

T31, T32, T36

For details about the device options see chapter under the same heading Insulation andheat tracing [ 64] in the MS code description.

If the sensor is insulated subsequently, the following must be noted: Do not insulate sensor terminal box. Do not expose transmitters to ambient temperatures exceeding 60 °C. The preferred insulation is 60 mm thick with a heat transfer coefficient of 0.4 W/m² K.

Ambient conditions

Rotamass NanoOperating conditions

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 29 / 68

Maximumtemperature of heatcarrier

Temperature specification MS code Position 8 Maximum temperature ofheat carrier in °C

Standard 0 0…150Mid-range 2 0…200

Electrical heating can be provided subsequently, such as in the form of heating tapes, aheating jacket or by way of hot water or steam running through copper pipes. When usingheat tracing, the sensor must be magnetically shielded in case its heat control is realizedby way of phase-angle control or pulse packets.

In hazardous areas, subsequent application of insulation, heating jacket or heat-ing strips is not permitted.

5.4 Ambient conditions

Rotamass can be used at demanding ambient conditions.

In doing so, the following specifications must be taken into account:

Ambient temperature Sensor: see [ 30] Transmitter: -40...60 °C Transmitter display has only limited legi-

bility below -20 °CStorage temperature Sensor: -50...80 °C

Transmitter: -40...60 °CRelative humidity 0...95 %IP code IP66/67 for transmitters and sensors when

using the appropriate cable glandsAllowable pollution degree in surroundingarea according to EN 61010-1

4 (in operation)

Vibration resistance according to IEC60068-2-6

Transmitter: 10...500 Hz, 1 g

Electromagnetic compatibility (EMC) ac-cording to IEC/EN 61326 as well as NA-MUR recommendation NE 21

Requirement during immunity tests: Theoutput signal fluctuation is specified withinthe ±1 % output span.

Maximum altitude 2000 m above mean sea level (MSL)Overvoltage category according to IEC/EN61010-1

II

Rotamass NanoOperating conditions Ambient conditions

30 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

5.4.1 Allowed ambient temperature for sensorThe allowed ambient temperature depends on the temperature specification, see Mediumtemperature range [ 24].

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

The allowed combinations of medium and ambient temperature for the sensor are illus-trated as gray areas in the diagrams below.

The Rotamass specification for use in Ex areas is different, see Ex instructionmanual (IM 01U10X-00EN).

TemperaturespecificationStandard

0

0 100-100-200

20

40

-40

-20

60

80

°C

°C

Tamb

T200 300

Fig. 21: Allowed medium and ambient temperatures

Tam

b

Ambient temperature

T Medium temperatureTemperaturespecification Mid-range

0

0 100-100-200

20

40

-40

-20

60

80

°C

°C

Tamb

T200 300

Fig. 22: Allowed medium and ambient temperatures

Ambient conditions

Rotamass NanoOperating conditions

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 31 / 68

5.4.2 Temperature specification by temperature classesMaximum ambient and process temperatures depending on explosion groups and tem-perature classes can be determined via the MS code or via the MS code together with theEx code.

MS code:

Pos. 2: N

Pos. 8: 0

Pos. 10: A, B, E, F

Pos. 11: KF21,KF22, SF21, SF22

Ex code:

The following figure shows the relevant positions of the MS code:

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Tab. 1: Temperature classification for explosion groups IIC, IIB

Temperatureclass

Maximum ambient temperature in °C

Maximum medium temperature in °C

T6 65 65T5 75 90T4 80 130T3 80 150T2 80 150T1 80 150

MS code:

Pos. 2: N

Pos. 8: 2

Pos. 10: B, F

Pos. 11: KF21,KF22, SF21, SF22

Ex code:

The following figure shows the relevant positions of the MS code:

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Tab. 2: Temperature classification for explosion groups IIC, IIB

Temperatureclass

Maximum ambient temperature in °C

Maximum medium temperature in °C

T6 65 65T5 75 90T4 80 130T3 80 180T2 80 260T1 80 260

Rotamass NanoMechanical specification Design

32 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

6 Mechanical specification

6.1 Design

The Rotamass Nano terminal box is available with two versions: Standard terminal box Long neck

Fig. 23: Standard terminal box and long neck

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Design Available temperaturespecifications

MS codePosition 10

Standard terminal box Standard A, E

Long neckStandardMid-range

B, F

If insulation (e.g. device option / T) is planned, it is mandatory to use the re-mote type with long neck.

The design influences the temperature specification for Ex-approved Rotamass,see Ex instruction manual (IM 01U10X-00EN-R).

Material

Rotamass NanoMechanical specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 33 / 68

6.2 Material

6.2.1 Material wetted partsFor Rotamass Nano, the measuring tubes are available in a corrosion-resistant nickel al-loy with process connections made of stainless steel alloy.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Material MS codePosition 4

Measuring tubes made of nickel alloy C-22/2.4602, process connections ofstainless steel alloy 1.4404/316L K

6.2.2 Non-wetted partsHousing material of sensor and transmitter each are product properties that are specifiedvia MS code position 7 and position 10.

Sensor housingmaterial - - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Housing material MS codePosition 7

Stainless steel 1.4301/304 0

Housing materialand coating oftransmitter

The transmitter housing is available with different coatings: PU coating

Urethane-cured polyester powder coating Corrosion protection coating

Anti-corrosion coating (multi-component coating with high mechanical and chemicalresistance)

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Housing material Coating MS codePosition 10

AluminumPU coating A, BCorrosion protection coating E, F

See also Design and housing [ 58].

Rotamass NanoMechanical specification

Process connections, dimensionsand weights of sensor

34 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

6.3 Process connections, dimensions and weights of sensor

L1 ±5

98

L7

L2

L2

L9

H5

H1

ø 102

H6

ø 102

80

L5

L1 ±3

ø 8,5

L6

L8

L4

H7

13

4

D2

42

5

H6

W3

10

2

L1

Fig. 24: Dimensions in mm

Overall length L1 see Process connections and overall length L1 [ 35].

Sensor andmeter size

L2 L4 L5 L6 L7 L8 L9 H1 H5 H6 H7 W3 D1 D2 Weight 1)

in mm in kgNano 06 150 270 180 111 110 180 210 25 101 176 350 160 165 299 5...14Nano 08 150 270 180 111 110 180 210 25 101 176 350 160 165 299 5...18Nano 10 150 270 180 99 110 180 210 25 101 176 350 160 165 299 5...18Nano 15 150 270 180 89 110 180 210 25 101 176 350 160 165 299 5...18Nano 20 150 270 180 55 110 180 210 25 101 176 350 160 165 299 5...18

1) Information on sensor weight with smallest and largest process connections, without in-sulation or heating

Process connections, dimensionsand weights of sensor

Rotamass NanoMechanical specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 35 / 68

The weight depends on the process connections.

6.3.1 Process connections and overall length L1The overall length of the sensor depends on the selected process connection (type andsize of flange). The following tables list the overall length as a function to the individualprocess connection.

Process connectionssuitable for ASMEB16.5

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

KN

Tab. 3: Overall length of sensor with ASME process connections made of stainless steel and wetted parts made of Ni alloyC-22/2.4602

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20ASME ½"class 150

15

BA1 240 240 240 240 240

ASME ½"class 300 BA2 240 240 240 240 240

ASME ½"class 600 BA4 250 250 250 250 250

ASME ½"class 600,ring joint

CA4 250 250 250 250 250

ASME ½"class 900 BA5 270 270 270 270 270

ASME ½"class 900,ring joint

CA5 270 270 270 270 270

ASME ½"class 1500 BA6 270 270 270 270 270

ASME ½"class 1500,ring joint

CA6 270 270 270 270 270

ASME 1"class 150

25

BA1 – 240 240 240 240

ASME 1"class 300 BA2 – 240 240 240 240

ASME 1"class 600 BA4 – 260 260 260 260

ASME 1"class 600,ring joint

CA4 – 260 260 260 260

ASME 1"class 900 BA5 – 320 320 320 320

ASME 1"class 900,ring joint

CA5 – 320 320 320 320

ASME 1"class 1500 BA6 – 320 320 320 320

ASME 1"class 1500,ring joint

CA6 – 320 320 320 320

Rotamass NanoMechanical specification Process connections, dimensions

36 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20ASME 1½"class 150

40

BA1 – 250 250 250 250

ASME 1½"class 300 BA2 – 250 250 250 250

ASME 1½"class 600 BA4 – 270 270 270 270

ASME 1½"class 600,ring joint

CA4 – 270 270 270 270

ASME 1½"class 900 BA5 – 340 340 340 340

ASME 1½"class 900,ring joint

CA5 – 340 340 340 340

ASME 1½"class 1500 BA6 – 340 340 340 340

ASME 1½"class 1500,ring joint

CA6 – 340 340 340 340

Meaning of "–": not available

Process connections, dimensions

Rotamass NanoMechanical specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 37 / 68

Process connectionssuitable for EN1092-1

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

KN

Tab. 4: Overall length of sensor with DIN process connections made of stainless steel and wetted parts made of Ni alloyC-22/2.4602

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20EN DN15PN40 profileB1

15

BD4 240 240 240 240 240

EN DN15PN40, pro-file D, withgroove

GD4 240 240 240 240 240

EN DN15PN40, pro-file E, withspigot

ED4 240 240 240 240 240

EN DN15PN40, pro-file F, withrecess

FD4 240 240 240 240 240

EN DN15PN100 pro-file B1

BD6 250 250 250 250 250

EN DN15PN100, pro-file D, withgroove

GD6 320 320 320 320 320

EN DN15PN100, pro-file E, withspigot

ED6 250 250 250 250 250

EN DN15PN100, pro-file F, withrecess

FD6 250 250 250 250 250

Rotamass NanoMechanical specification Process connections, dimensions

38 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20EN DN25PN40 profileB1

25

BD4 – 240 240 240 240

EN DN25PN40, pro-file D, withgroove

GD4 – 240 240 240 240

EN DN25PN40, pro-file E, withspigot

ED4 – 240 240 240 240

EN DN25PN40, pro-file F, withrecess

FD4 – 240 240 240 240

EN DN25PN100 pro-file B1

BD6 – 260 260 260 260

EN DN25PN100, pro-file D, withgroove

GD6 – 260 260 260 260

EN DN25PN100, pro-file E, withspigot

ED6 – 260 260 260 260

EN DN25PN100, pro-file F, withrecess

FD6 – 260 260 260 260

Process connections, dimensions

Rotamass NanoMechanical specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 39 / 68

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20EN DN40PN40 profileB1

40

BD4 – 240 240 240 240

EN DN40PN40, pro-file D, withgroove

GD4 – 240 240 240 240

EN DN40PN40, pro-file E, withspigot

ED4 – 240 240 240 240

EN DN40PN40, pro-file F, withrecess

FD4 – 240 240 240 240

EN DN40PN100 pro-file B1

BD6 – 320 320 320 320

EN DN40PN100, pro-file D, withgroove

GD6 – 320 320 320 320

EN DN40PN100, pro-file E, withspigot

ED6 – 320 320 320 320

EN DN40PN100, pro-file F, withrecess

FD6 – 320 320 320 320

Meaning of "–": not available

Rotamass NanoMechanical specification Process connections, dimensions

40 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Process connectionssuitable for JIS B2220

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

KN

Tab. 5: Overall length of sensor with JIS process connections made of stainless steel and wetted parts made of Ni alloyC-22/2.4602

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20JIS DN1510K

15BJ1 240 240 240 240 240

JIS DN1520K BJ2 240 240 240 240 240

JIS DN2510K

25BJ1 – 240 240 240 240

JIS DN2520K BJ2 – 240 240 240 240

JIS DN4010K

40BJ1 – 240 240 240 240

JIS DN4020K BJ2 – 240 240 240 240

Meaning of "–": not available

Process connectionssuitable for JPI - - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

KN

Tab. 6: Overall length of sensor with JPI process connections and wetted parts made of stainless steel

Internalthread

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20JPI ½" class150

15

BP1 240 240 240 240 240

JPI ½" class300 BP2 240 240 240 240 240

JPI ½" class600 BP4 250 250 250 250 250

JPI 1" class150

25

BP1 – 240 240 240 240

JPI 1" class300 BP2 – 240 240 240 240

JPI 1" class600 BP4 – 260 260 260 260

JPI 1½"class 150

40

BP1 – 250 250 250 250

JPI 1½"class 300 BP2 – 250 250 250 250

JPI 1½"class 600 BP4 – 270 270 270 270

Meaning of "–": not available

Process connections, dimensions

Rotamass NanoMechanical specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 41 / 68

Process connectionswith DIN clampedconnection

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

KN

Tab. 7: Overall length of sensor with wetted parts made of Ni alloy C-22/2.4602, process connection: DIN clamped connec-tion made of stainless steel

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20DIN 32676DN15 15 HS4 240 240 240 240 240

DIN 32676DN25 25 HS4 – 240 240 240 240

DIN 32676DN40 40 HS4 – 240 240 240 240

Meaning of "–": not available

Process connectionswith clamped con-nection suitable forTri-Clamp

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

KN

Tab. 8: Overall length of sensor with wetted parts made of Ni alloy C-22/2.4602, process connection: Tri-Clamp clampedconnection made of stainless steel

Process con-nections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20Tri-Clamp ½" 15

HS8240 240 240 240 240

Tri-Clamp 1" 25 – 240 240 240 240Tri-Clamp 1½" 40 – 240 240 240 240

Meaning of "–": not available

Process connectionswith internal thread - - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

KN

Tab. 9: Overall length of sensor including process connections with internal thread made of stainless steel and wetted partsmade of Ni alloy C-22/2.4602

Processconnections

MS codePosition 5

MS codePosition 6

L1 in mm according to meter size(MS code position 3)

Nano 06 Nano 08 Nano 10 Nano 15 Nano 20NPT ¼" 06

TT9

260 260 260 260 260NPT ⅜" 08 260 260 260 260 260NPT ½" 15 260 260 260 260 260NPT ¾" 20 260 260 260 260 260

Rotamass NanoMechanical specification Transmitter dimensions

42 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

6.4 Transmitter dimensions

19

1,7

17

5

123

14

0

240,9

42 96,2

69,7

42

42

23

14

9,5

87,8 73

12

8

60

34

4x M

6

19

1,7

17

5

123

14

0

220,9

42 96,2

69,7

42

42

23

14

9,5

67,8 73

12

8

60

34

4x M

6

Fig. 25: Dimensions of transmitter in mm (left: transmitter with display, right: transmitter without dis-play)

10098

104

DN50

Fig. 26: Dimensions of transmitter in mm, attached by sheet metal console (bracket)

Rotamass NanoTransmitter specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 43 / 68

7 Transmitter specification

Overview offunctional scope ofthe Rotamasstransmitter

TransmitterFunctional scope Essential Ultimate

YOKOGAWA

Essential

YOKOGAWA

Essential

YOKOGAWA

Ultimate

YOKOGAWA

Ultimate

MS code (Position 1) E U4-line Dot-Matrix display Universal power supply (VDC and VAC) InstallationIntegral type Remote type Special functionsWizard Event management microSD card Total-Health-Check Special functions for applicationsDynamic pressure compensation1) − Inline concentration measurement − Measurement of heat quantity1) − Inputs and outputsAnalog output Pulse/frequency output Status output Analog input − Status input CommunicationHART

1) Only in combination with an analog input

Rotamass NanoTransmitter specification Inputs and outputs

44 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

7.1 Inputs and outputs

Depending on flow meter specification, different configurations of connection terminal ex-ist. The following is an explanation of a possible configuration of the connection terminals:

WP

ON/

OFF

SinIout1 P/Sout1 Iin

Iout1 Current output (active/passive) Iin Current input (active/passive)P/Sout1 Passive pulse or

status outputWP Write-protect bridge

Sin Status input

Inputs and outputs

Rotamass NanoTransmitter specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 45 / 68

7.1.1 Output signalsGalvanic isolation All circuits for inputs, outputs and power supply are galvanically isolated from each other.Active currentoutput lout

One or two current outputs are available depending on MS code position 13.

Depending on the measured value, the active current output delivers 4...20 mA.

It may be used for output of the following measured values (see also the correspondingsoftware instruction manual):

Flow rate (mass, volume, net partial component flow of a mixture) Density Temperature Pressure Concentration

For HART communication devices, it is supplied on the current output lout1. The currentoutput may be operated in compliance with the NAMUR NE43 standard. For details seee.g., software instruction manual HART IM01U10S01-00-R (chapter "Configuration ofanalog output 1")

ValueOutput current 2.4...21.6 mALoad resistance ≤ 750 ΩLoad resistance for secure HART communi-cation 230...600 Ω

Additive maximum deviation 0.05 % of maximum currentAdditive deviation in case of 20 °C deviationof ambient temperature 0.05 % of maximum current per 10 °C

Iout+

Iout-

ROTAMASS

1

Fig. 27: Active current output connection lout

① Receiver

Rotamass NanoTransmitter specification Inputs and outputs

46 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Passive currentoutput lout

Current output: 4...20 mA

ValueOutput current 2.4...21.6 mAExternal power supply 10.5...32 VDC

Load resistance for secure HARTcommunication 230...600 Ω

Load resistance at current output ≤ 911 ΩAdditive maximum deviation 0.05 % of maximum currentAdditive deviation in case of 20 °C deviationof ambient temperature 0.05 % of maximum current per 10 °C

R =U - 10.5 V

0.0236 A

911

U in V

3210.5

R in

Ω

0

Fig. 28: Maximum load resistance as a function of receiver output current

R Load resistanceU Output voltage of receiver

The diagram shows the maximum load resistance R as a function of voltage U of the con-nected voltage source. Higher load resistances are allowed with higher power supply val-ues. The usable zone for passive power output operation is indicated by the hatchedarea.

U

R

Iout+

Iout-

ROTAMASS

Fig. 29: Passive current output connection lout

Inputs and outputs

Rotamass NanoTransmitter specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 47 / 68

Active pulse output P/Sout

Connection of an electronic counterMaximum voltage and correct polarity must be observed for wiring.

ValueLoad resistance ≥ 1 kΩAllowed load current ≤ 200 mAInternal power supply 24 VDC ±20 %Maximum pulse rate 12500 pulses/sFrequency range 0...12.5 kHz

P/Sout+

P/Sout-

24 V

0 V

1

ROTAMASS

2

Fig. 30: Active pulse output connection P/Sout

① Load resistance② Electronic counter

Connection of an electromechanical counter

ValueMaximum current 150 mAAverage current ≤ 30 mAInternal power supply 24 VDC ±20 %Maximum pulse rate 2 pulses/sPulse length 20, 33, 50, 100 ms

P/Sout+

P/Sout-

24 V

0 V

1

ROTAMASS

2

Fig. 31: Active pulse output P/Sout connection with electromechanical counter

① Protective diode② Electromechanical counter

Rotamass NanoTransmitter specification Inputs and outputs

48 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Active pulse output P/Sout with internalpull-up resistor

ValueInternal power supply 24 VDC ±20 %Internal pull-up resistor 2.2 kΩMaximum pulse rate 12500 pulses/sFrequency range 0...12.5 kHz

1

P/Sout+

P/Sout-

24 V

0 V

ROTAMASS

Fig. 32: Active pulse output P/Sout with internal pull-up resistor

① Electronic counter

Passive pulse output P/Sout

Maximum voltage and correct polarity must be observed for wiring.

ValueMaximum load current ≤ 200 mAPower supply ≤ 30 VDC

Maximum pulse rate 12500 pulses/sFrequency range 0...12.5 kHz

ROTAMASS

P/Sout+

P/Sout-

321

Fig. 33: Passive pulse output connection P/Sout with load resistance

① Passive pulse or status output② Load resistance③ Electronic counter

ROTAMASS

P/Sout+

P/Sout-

321

Fig. 34: Passive pulse output P/Sout connection with protective diode

① Passive pulse or status output② Protective diode③ Electromechanical counter

Inputs and outputs

Rotamass NanoTransmitter specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 49 / 68

Active status output P/Sout

Since this is a transistor contact, maximum allowed current as well as polarity and level ofoutput voltage must be observed during wiring.

ValueLoad resistance > 1 kΩInternal power supply 24 VDC ±20 %

P/Sout+

P/Sout-

24 V

0 V

1

ROTAMASS

Fig. 35: Active status output connection P/Sout

① External device with load resistance

Active status output P/Sout with internalpull-up resistor

ValueInternal pull-up resistor 2.2 kΩInternal power supply 24 VDC ±20 %

1

P/Sout+

P/Sout-

24 V

0 V

ROTAMASS

Fig. 36: Active status output P/Sout with internal pull-up resistor

① External device

Rotamass NanoTransmitter specification Inputs and outputs

50 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Passive statusoutput P/Sout

Since this is a transistor contact, maximum allowed power supply, its polarity as well asmaximum allowed current must be observed during wiring.

ValueAllowed load current ≤ 200 mAPower supply ≤ 30 VDC

P/Sout+ or Sout+

P/Sout- or Sout-

1

ROTAMASS

Fig. 37: Passive status output connection P/Sout with protective diode

① External device

A relay must be connected in series to switch alternating voltage.

P/Sout- or Sout-

P/Sout+ or Sout+

2

3

1

ROTAMASS

4

Fig. 38: Passive status output connection P/Sout for solenoid valve circuit

① Relay② Solenoid valve③ Magnetic valve power supply④ Protective diode

Passive pulse orstatus output P/Sout(NAMUR)

According to EN 60947-5-6 (previously NAMUR, worksheet NA001)

10kΩ

1kΩROTAMASS

P/Sout+

P/Sout-

21

Fig. 39: Passive pulse or status output with switching amplifier connected in series

① Passive pulse or status output② Switching amplifier

Inputs and outputs

Rotamass NanoTransmitter specification

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 51 / 68

7.1.2 Input signalsActive current input lin

An individual analog power input is available for external analog devices.

The active current input lin is provided for connecting a two-wire transmitter with an out-put signal of 4..20 mA.

ValueInput current 2.4...21.6 mAInternal power supply 24 VDC ±20 %Internal load resistance Rotamass ≤ 160 Ω

Iin+

Iin-

24 V

ROTAMASS

0 V

1

Fig. 40: Connection of external device with passive current output

① External passive current output device

Passive currentinput lin

The passive current input lin is provided for connecting a four-wire transmitter with an out-put signal of 4...20 mA.

ValueInput current 2.4...21.6 mAMaximum input voltage ≤ 32 VDC

Internal load resistance Rotamass ≤ 160 Ω

Iin+

Iin-

ROTAMASS

1

Fig. 41: Connection of external device with active current output

① External active current output device

Rotamass NanoTransmitter specification Power supply

52 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Status input Sin

Do not connect a signal source with electric voltage.

The status input is provided for use of voltage-free contacts with the following specification:

Switching status ResistanceClosed < 200 ΩOpen > 100 kΩ

ROTAMASS

Sin+

Sin-

Fig. 42: Status input connection

7.2 Power supply

Power supply Alternating voltage (rms):– Power supply: 24 VAC or 100...240 VAC

– Power frequency: 47...63 Hz Direct-current voltage:

– Power supply: 24 VDC or 100...120 VDC

Power consumption P = 10 W (including sensor)Power supply failure In the event of a power failure, the flow meter data are backed up on a non-volatile inter-

nal memory. In case of devices with display, the characteristic sensor values, such asnominal diameter, serial number, calibration constants, zero point, etc. and the error his-tory are also stored on a microSD card.

Critical values may also be recorded on a microSD card during operation. It also holdsproduct documentation and a data backup of factory settings in order to facilitate recoveryin case of device failure.

In the event of a power failure, the flow meter bridges at least one power line cycle.Potentialequalization

Potential equalization must be ensured at all times, see user's manualIM 01U10A-00EN With respect to explosion protection, refer to the relevant informationin the specific documents in the Ex instruction manual IM 01U10X0-00EN.

7.3 Cable specification

The original connecting cable from Rota Yokogawa must be used to connect the sensorwith the transmitter. The connecting cable included in the delivery may be shortened. Anassembly set along with the appropriate instructions are enclosed for this purpose.

The connecting cable can be ordered in various lengths as a device option, see chapterConnecting cable length [ 61].

If a different cable is to be used, it is important to contact your Yokogawa sales organiza-tion about the necessary cable specifications.

Rotamass NanoApprovals and declarations of conformity

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 53 / 68

8 Approvals and declarations of conformity

CE marking The Rotamass Coriolis flow meter meets the statutory requirements of the applicable EUDirectives. By attaching the CE mark, Rota Yokogawa confirms conformity of the field in-strument with the requirements of the applicable EU Directives. The EU Declaration ofConformity is enclosed with the product on a data carrier.

RCM Rotamass Coriolis flow meter meets the EMC requirements of the Australian Communi-cations and Media Authority (ACMA).

Ex approvals All data relevant for explosion protection are included in separate Ex instruction manuals.Pressure equipmentapprovals

The Rotamass Coriolis flow meter is in compliance with the statutory requirements of theapplicable EU Pressure Equipment Directive (PED).

Rotamass NanoOrdering information MS code

54 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

9 Ordering information

9.1 MS code

The MS code of the Rotamass TI is explained below.

Items 1 through 14 are mandatory entries and must be specified at the time of ordering.

Device options (item 15) can be selected and specified individually by separating themwith slashes.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

1. Transmitter2. Sensor3. Meter size4. Material wetted parts5. Process connection size6. Process connection type7. Sensor housing material8. Medium temperature range9. Mass flow and density accuracy10. Design and housing11. Ex approval12. Cable entries13. Communication type and I/O14. Display15. Options

Details are available in the general Specifications of the corresponding Rotamass series.

9.1.1 Transmitter

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 1

Transmitter

E EssentialU Ultimate

9.1.2 Sensor

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 2

Sensor

N Nano

MS code

Rotamass NanoOrdering information

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 55 / 68

9.1.3 Meter size

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 3

Meter size Nominal mass flowin t/h

06 06 0.02108 08 0.04510 10 0.1715 15 0.3720 20 0.95

9.1.4 Material wetted parts

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 4

Material wetted parts

KMeasuring tubes: Ni alloy C-22/2.4602Process connections: Stainless steel 1.4404/316L

9.1.5 Process connection size

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 5

Process connection size

6 DN6, 1/4"8 DN8, 3/8"15 DN15, 1/2"20 DN20, 3/4"25 DN25, 1"40 DN40, 1 1/2"

Available sizes depend on the actual process connection, see also chapterProcess connections and overall length L1 [ 35].

Rotamass NanoOrdering information MS code

56 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

9.1.6 Process connection type

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 6

Type Process connections

BA1

Flanges suitable forASME B16.5

ASME flange class 150BA2 ASME flange class 300BA4 ASME flange class 600CA4 ASME flange class 600, ring jointBA5 ASME flange class 900CA5 ASME flange class 900, ring jointBA6 ASME flange class 1500CA6 ASME flange class 1500, ring jointBD4

Flange suitable for EN1092-1

EN flange PN40, profile B1ED4 EN flange PN40, profile E, with spigotFD4 EN flange PN40, profile F, with recessGD4 EN flange PN40, profile D, with grooveBD6 EN flange PN100, profile B1ED6 EN flange PN100, profile E, with spigotFD6 EN flange PN100, profile F, with recessGD6 EN flange PN100, profile D, with grooveBJ1 Flange suitable for JIS B

2220JIS flange 10K

BJ2 JIS flange 20KBP1

Flange suitable for JPIJPI flange class 150

BP2 JPI flange class 300BP4 JPI flange class 600HS4

Clamped connectionsProcess connection according to DIN 32676

HS8 Process connection according to Tri-Clover (Tri-Clamp) and Mini-Clamp

TG9 Process connections withinternal thread

Process connection with internal thread GTT9 Process connection with internal thread NPT

9.1.7 Sensor housing material

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 7

Housing material

0 Stainless steel 1.4301/304

MS code

Rotamass NanoOrdering information

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 57 / 68

9.1.8 Medium temperature range

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 8

Temperature range Medium temperature range

0 Standard -50...150 °C2 Mid-range -50...260 °C

For temperature range limits, see chapter Medium temperature range [ 24].

9.1.9 Mass flow and density accuracy

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Medium MS codePosition 9

Maximum deviation MS codePosition 1Mass flow

Dflat in %Density

in g/l

Liquid

E90.2

20 EE8 8 EE7 4 ED9

0.15

20 UD8 8 UD7 4 UD3 1 UD2 0.5 UC8

0.1

8 UC7 4 UC3 1 UC2 0.5 U

Gas70 0.75 – E50 0.5 – U

Devices with value 2 in MS code position 9 receive an additional density calibration witha corresponding certificate.

Rotamass NanoOrdering information MS code

58 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

9.1.10 Design and housing

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 10

Design Transmitter housing material

Transmitterhousingcoating

Sensorterminal box material

Long neck

A

Remote type Aluminum

PU coatingStainlesssteel

NoB YesE Corrosion

protectioncoating

No

F Yes

A connecting cable is required to connect the sensor with the transmitter. It can be se-lected in various lengths as a device option, see Connecting cable length [ 61].

9.1.11 Ex approval

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 11

Ex approval

NN00 NoneKF21 ATEX, explosion group IIC and IIICKF22 ATEX, explosion group IIB and IIICSF21 IECEx, explosion group IIC and IIICSF22 IECEx, explosion group IIB and IIIC

MS code

Rotamass NanoOrdering information

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 59 / 68

9.1.12 Cable entries

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

MS codePosition 12

Cable entries

2 ANSI 1/2" NPT4 ISO M20x1.5

9.1.13 Inputs and outputs

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

HART I/O MS codePosition 13

Connection terminal assignmentI/O1 +/- I/O2 +/- I/O3 +/- I/O4 +/- WP

JAIout1Active

P/Sout1Passive

– – Write-protect

JBIout1Active

P/Sout1Passive

P/Sout2Passive

Iout2Active

Write-protect

JCIout1Active

P/Sout1Passive

SinIout2Active

Write-protect

JDIout1Active

P/Sout1Passive

SoutPassive

P/Sout2Passive

Write-protect

JEIout1Active

P/Sout1Passive

SinP/Sout2Passive

Write-protect

JFIout1Active

P/Sout1Passive

Sin

P/Sout2ActiveInternal pull-up resistor

Write-protect

JGIout1Active

P/Sout1Passive

SinP/Sout2Active

Write-protect

JHIout1Active

P/Sout1Passive

Iout2Passive

IinActive

Write-protect

JJIout1Active

P/Sout1Passive

P/Sout2Passive

IinActive

Write-protect

JKIout1Active

P/Sout1Passive

SinIinActive

Write-protect

JLIout1Active

P/Sout1Passive

Iout2Passive

IinPassive

Write-protect

JMIout1Active

P/Sout1Passive

P/Sout2Passive

IinPassive

Write-protect

JNIout1Active

P/Sout1Passive

SinIinPassive

Write-protect

Iout1 Active or passive current output with HART communicationIout2 Active or passive current outputIin Active or passive current input

Rotamass NanoOrdering information MS code

60 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

P/Sout1 Passive pulse or status outputP/Sout2 Active or passive pulse or status outputSin Status inputSout Status output

HART I/O,intrinsically safe

MS codePosition 13

Connection terminal assignmentI/O1 +/- I/O2 +/- I/O3 +/- I/O4 +/- WP

JPIout1Passive

P/Sout1Passive

Iout2Passive

– Write-protect

JQIout1Passive

P/Sout1Passive

Iout2Passive

P/Sout2Passive

Write-protect

JRIout1Passive

P/Sout1PassiveNAMUR

Iout2Passive

– Write-protect

JSIout1Passive

P/Sout1PassiveNAMUR

Iout2Passive

P/Sout2PassiveNAMUR

Write-protect

Intrinsically safe outputs are only available in combination with selecting Ex approval ofthe device, see chapter Ex approval [ 58].

9.1.14 Display

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

The display unit includes a slot for the microSD card.

MS codePosition 14

Display

0 Without display1 With display

Devices without a display are available for Essential transmitters only (value E in MS codeposition 1)

Options

Rotamass NanoOrdering information

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 61 / 68

9.2 Options

Additional device options that can be combined may be selected; they are listed sequen-tially in MS code position 15. In this case, each device option is preceded by a slash.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

The following device options are possible: Connecting cable length, see chapter Connecting cable length [ 61] Customer-specific adaptation of the nameplate, see chapter Additional nameplate in-

formation [ 61] Flow meter presetting with customer parameters, see chapter Presetting of customer

parameters [ 62] Concentration measurement, see chapter Concentration measurement Insulation and heat tracing, see chapter Insulation and heat tracing [ 64] Certificates to be supplied, see chapter Certificates [ 64] Positive Material Identification of wetted parts, see chapter Certificates [ 64] X-ray inspection of flange weld seam, see chapter Certificates [ 65] Tube health check, see chapter Tube health check [ 66] Fixing device for sensor, see chapter Fixing device [ 66] Measurement of heat quantity, see chapter Measurement of heat quantity [ 66]

9.2.1 Connecting cable lengthWhen ordering, specification of the desired connecting cable length is always required.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options SpecificationL000 Specially ordered connecting cableL005 Cable length 5 m (16.4 ft)L010 Cable length 10 m (32.8 ft)L015 Cable length 15 m (49.2 ft)L030 Cable length 30 m (98.4 ft)

9.2.2 Additional nameplate information

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options SpecificationBG Nameplate with customer-specific identification

This marking must be provided by the customer at the time the order is placed.

Rotamass NanoOrdering information Options

62 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

9.2.3 Presetting of customer parametersRotamass flow meters can be preconfigured with customer-specific data.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options Specification

PSPresetting according to customer parameters.This information must be provided by the customer in the YokogawaFlowConfigurator software at the time the order is placed.

9.2.4 Concentration measurementThe standard concentration measurement (device option CST) can be used for concen-tration measurements of emulsions or suspensions when density of the media involveddepends only on temperature.

The standard concentration measurement can also be used for many low-concentrationsolutions if there is only minor interaction between the liquids or if the miscibility is negligi-ble. For questions regarding a specific application, contact the responsible Yokogawasales organization. The appropriate density coefficients must be determined prior to usingthis option and input into the transmitter. To do so, the recommendation is to determinethe necessary parameters from density data using DTM in the Yokogawa FieldMate pro-gram or the calculation tool inclduded in the delivery.

The advanced concentration measurement is recommended for more complex applica-tions, such as for liquids that interact.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options SpecificationCST Standard concentration measurementAC0 Advanced concentration measurement, customer settingsAC1 Advanced concentration measurement, one default data setAC2 Advanced concentration measurement, two default data setsAC3 Advanced concentration measurement, three default data setsAC4 Advanced concentration measurement, four default data sets

These device options are not available in combination with gas measurement devices(model code position 9 with the values: 70 or 50).

Options with AC are available only for Ultimate transmitters (value U in MS code posi-tion 1).

Sets must be selected for AC1...AC4 options. Not applicable to AC0 option.

Options

Rotamass NanoOrdering information

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 63 / 68

Following is a table that lists possible pre-configured concentrations. The desired datasets must be requested by the customer to the Yokogawa sales organization at the timethe order is placed. The customer is responsible to ensure chemical compatibility of thematerial of the wetted parts with the measured chemicals. For strong acids or oxidizerswhich attack steel pipes a variant with wetted parts made of Ni alloy C-22/2.4602 is nec-essary.

Set Medium A / B

Concentrationrange

Unit Tempera-ture range

in °C

Density rangein kg/l

Data source for density data

C01 Sugar / Water 0...85 °Brix 0...80 0.97...1.45

PTB... Messages 100 5/90: "Thedensity of watery sucrose solu-tions after the introduction of theinternational temperature scaleof 1990 (ITS1990)" Table 5

C02 1) NaOH /Water 0...54 WT% 0...100 0.95...1.58

D´Ans-Lax, Handbook forchemists and physicists Vol.1,3rd edition, 1967

C03 KOH / Water 1...55 WT% 54...100 1.01...1.58

D´Ans-Lax, Handbook forchemists and physicists Vol.1,3rd edition, 1967

C04 NH4NO3 /Water 1...50 WT% 0...80 0.97...1.24 Table of density data on request

C05 NH4NO3 /Water 20...70 WT% 20...100 1.04...1.33 Table of density data on request

C06 1) HCl / Water 22...34 WT% 20...60 1.08...1.17

D´Ans-Lax, Handbook forchemists and physicists Vol.1,3rd edition, 1967

C07 HNO3 / Water 50...67 WT% 10...60 1.26...1.40 Table of density data on request

C09 1) H2O2 / Water 30...75 WT% 4.5...43.5 1.00...1.20 Table of density data on request

C10 1)Ethyleneglycol / Water

10...50 WT% 20...40 1.005...1.085 Table of density data on request

C11 Starch /Water 33...42.5 WT% 35...45 1.14...1.20 Table of density data on request

C12 Methanol/ Water 35...60 WT% 0...40 0.89...0.96 Table of density data on request

C20 Alcohol /Water 55...100 VOL% 10...40 0.76...0.94 Table of density data on request

C21 Sugar / Water 40...80 °Brix 75...100 1.15...1.35 Table of density data on request

C30 Alcohol /Water 66...100 WT% 15...40 0.77...0.88 Standard Copersucar 1967

C37 Alcohol /Water 66...100 WT% 10...40 0.772...0.885 Brazilian Standard ABNT

1) We recommend using devices with wetted parts made of nickel alloy C33. Contact theYokogawa sales organization about availability.

Rotamass NanoOrdering information Options

64 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

9.2.5 Insulation and heat tracingThese device options are available only for remote type with long neck.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options SpecificationT10 InsulationT21 Insulation and heat tracing, 1/2" ANSI 150T22 Insulation and heat tracing, 1/2" ANSI 300T26 Insulation and heat tracing, DN15 PN40T31 Insulation, heat tracing with ventilation, 1/2" ANSI 150T32 Insulation, heat tracing with ventilation, 1/2" ANSI 300T36 Insulation, heat tracing with ventilation, DN15, PN40

9.2.6 Certificates

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Accordance withterms of order

Options SpecificationP2 Declaration of compliance with the order 2.1 according to EN 10204

P3 Quality Inspection Certificate (Inspection Certificate 3.1 according to EN 10204)

Material certificates Options Specification

P6 Certificate of Marking Transfer and Raw Material Certificates(Inspection Certificate 3.1 according to EN 10204)

Dye penetration testof weld seams

Options Specification

PT Dye penetration test of process connection weld seams according toDIN EN ISO 3452-1, including certificate

Positive MaterialIdentification ofwetted parts

Options Specification

PM Positive Material Identification of wetted parts, including certificate(Inspection Certificate 3.1 according to EN 10204)

Pressure testing Options Specification

P8 Hydrostatic Pressure Test Certificate (Inspection Certificate 3.1 according to EN 10204)

Welding certificates Options Specification

WP

Welding certificates: WPS according to DIN EN ISO 15609-1 WPQR according to DIN EN ISO 15614-1 WQC according to DIN EN 287-1 or DIN EN ISO 6906-4

Mass flowcalibration

Water is used as medium for calibrating the Rotamass.

Options Specification

K2Customer-specific 5-point mass flow calibration with factory calibrationcertificate (mass flow or volume flow of water). A table listing the de-sired calibration points must be supplied with the order.

K5Customer-specific 10-point mass flow calibration with DAkkS calibra-tion certificate (mass flow or volume flow of water). A table listing thedesired calibration points must be supplied with the order.

Options

Rotamass NanoOrdering information

GS 01U10B01-00EN-R_001, 1st edition, 1st edition, 2016-05-18 65 / 68

Calibrationcertificates

Options Specification

L2The certificate confirms that the delivered instrument has undergone acalibration traceable to national standards, including a list of workingstandards used for calibration. Language: English/Japanese

L3

The certificate confirms that the delivered instrument has undergone acalibration traceable to national standards, including a list of primarystandards to which the delivered product is traceable. Language:English/Japanese

L4

The certificate confirms that the delivered instrument has undergone acalibration traceable to national standards and that the calibration sys-tem of Rota Yokogawa is traceable to national standards. Language:English/Japanese

Surfaces free of oiland grease

Options Specification

H1 Degreasing of wetted surfaces according to ASTM G93-03 (Level C),including test report

Country-specificdelivery

Options Specification

PJ Quality Inspection Certificate according to the "Quality InspectionStandard" of Rotamass TI. Language: English/Japanese

X-ray inspection offlange weld seam

Options Specification

RT

X-ray inspection of flange weld seam according to DIN EN ISO17636-1/BEvaluation according to AD2000HP 5/3 and DIN EN ISO 5817/C,including certificate

This device option is not available for devices with wetted parts made of Ni alloyC-22/2.4602.

In case of devices from the Nanofamily, where MS code position 9 includes the value C2,D2, C3 or D3, an X-ray inspection can only be performed on one of the two process con-nections as a result of structural conditions.

Combinedcertificates

Options Specification

P10

Combination of: P3: Quality Inspection Certificate P6: Certificate of Marking Transfer and Raw Material Certificates P8: Hydrostatic Pressure Test Certificate

P11

Combination of: P3: Quality Inspection Certificate P6: Certificate of Marking Transfer and Raw Material Certificates PM: Positive Material Identification of wetted parts

P12

Combination of: P3: Quality Inspection Certificate P6: Certificate of Marking Transfer and Raw Material Certificates PT: Dye penetration test according to DIN EN ISO 3452-1 P8: Hydrostatic Pressure Test Certificate

P13

Combination of: P3: Quality Inspection Certificate P6: Certificate of Marking Transfer and Raw Material Certificates PT: Dye penetration test according to DIN EN ISO 3452-1 PM: Positive Material Identification of wetted parts P8: Hydrostatic Pressure Test Certificate WP: Welding certificates

Rotamass NanoOrdering information Options

66 / 68 GS 01U10B01-00EN-R_001, 1st edition, 2016-05-18

Options Specification

P14

Combination of: PM: Positive Material Identification of wetted parts P8: Hydrostatic Pressure Test Certificate WP: Welding certificates

9.2.7 Tube health checkBy way of the tube health check, the transmitter can determine whether the tube proper-ties were altered due to corrosion or deposits and, whether they could impact accuracyas a result.

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options SpecificationTC Tube health check

9.2.8 Fixing device

Options SpecificationPD 2" fixing device for sensor

This option cannot be used together with device option T.

9.2.9 Measurement of heat quantity

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options Specification

CGC

Measurement of the total transported energy content of a fuel in con-nection with a sensor for determining the fuel's calorific value (e.g., agas chromatograph, not included in scope of delivery).This option is available only together with MS code position 13 JH toJN.

9.2.10 Customer specific special product manufacture

- - - - /-RC

1 2 3 4 6 75 9 10 11 12 13 14 158

Options SpecificationZ Deviations from the specifications in this document are possible.

Rotamass NanoOrdering information

GS 01U10B01-00EN-R - 001, 1st edition, 2016-05-18 67 / 68

YOKOGAWA ELECTRIC CORPORATION

YOKOGAWA CORPORATION OF AMERICA

YOKOGAWA AMERICA DO SUL LTDA.

YOKOGAWA EUROPE B. V.

Euroweg 2, 3825 HD Amersfoort,

THE NETHERLANDS

Phone : 31-88-4641000

Fax : 31-88-4641111

YOKOGAWA INDIA LTD.

Plot No.96, Electronic City Complex,

Hosur Road, Bangalore - 560 100,

INDIA

Phone : 91-80-4158-6000

Fax : 91-80-2852-1442

YOKOGAWA AUSTRALIA PTY. LTD.

Tower A, 112-118 Talavera Road,

Macquarie Park NSW 2113,

AUSTRALIA

Phone : 61-2-8870-1100

Fax : 61-2-8870-1111

YOKOGAWA MIDDLE EAST & AFRICA B.S.C.(C)

P.O. Box 10070, Manama, Building 577,

Road 2516, Busaiteen 225, Muharraq,

Kingdom of BAHRAIN

Phone : 973-17358100

Fax : 973-17336100

Headquarters

2-9-32, Nakacho, Musashino-shi,

Tokyo, 180-8750 JAPAN

Phone : 81-422-52-5555

Branch Sales Offices

Osaka, Nagoya, Hiroshima,

Kurashiki, Fukuoka, Kitakyusyu

Head Office

12530 West Airport Blvd, Sugar Land,

Texas 77478, USA

Phone : 1-281-340-3800

Fax : 1-281-340-3838

Georgia Office

2 Dart Road, Newnan, Georgia 30265, USA

Phone : 1-800-888-6400/ 1-770-253-7000

Fax : 1-770-254-0928

Praca Acapulco, 31 - Santo Amaro, Sáo Paulo/SP,

BRAZIL, CEP-04675-190

Phone : 55-11-5681-2400

Fax : 55-11-5681-4434

YOKOGAWA ELECTRIC CIS LTD.

Grokholskiy per 13 Building 2, 4th Floor 129090,

Moscow, RUSSIA

Phone : 7-495-737-7868

Fax : 7-495-737-7869

YOKOGAWA CHINA CO., LTD.

3F Tower D Cartelo Crocodile Building,

No.568 West Tianshan Road,

Shanghai 200335, CHINA

Phone : 86-21-62396262

Fax : 86-21-62387866Z

YOKOGAWA ELECTRIC KOREA CO., LTD.

(Yokogawa B/D, Yangpyeong-dong 4-Ga),21, Seonyu-ro 45-gil, Yeongdeungpo-gu,Seoul, 150-866, KOREA

Phone : 82-2-2628-6000

Fax : 82-2-2628-6400

YOKOGAWA ENGINEERING ASIA PTE. LTD.

5 Bedok South Road, Singapore 469270,

SINGAPORE

Phone : 65-6241-9933

Fax : 65-6241-2606 ISO 9001

GS 01U10B01-00EN-R - 001, 1st edition, 2016-05-18

All rights reserved. Copyright © 2016-05-18