roto nt designo - roto north america · 8 february 2017 imo_109_de_v5_en roto nt designo subject to...

Window and Door Technology

Roto NT DesignoConcealed hinge solution for windows and balcony doors with high sash weights up to 150 kg

Installation, maintenance and operation instructionsfor timber windows and balcony doors – 13 mm hardware axis

ImprintCopyright: February 2017

Roto Frank AGWindow and Door Technology

Wilhelm-Frank-Platz 1

70771 Leinfelden-Echterdingen

Germany

Phone +49 711 7598 0

Fax +49 711 7598 253

[email protected]

www.roto-frank.com

Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 3

General information Information on these instructions ....................................................5

Responsibility of the target groups ..................................................6

Instruction obligation of the target groups ......................................7

Explanation of the safety instruction symbols .................................8

Limitation of liability ........................................................................9

Safety Stipulated use ................................................................................ 10

Stipulated application for end-users .............................................. 11

Safety instructions ......................................................................... 12

Safety information for end-users .................................................. 13

Fabrication advice .......................................................................... 14

Screw fixing ................................................................................... 15

Information on the product General hardware characteristics ................................................... 17

Introduction ................................................................................... 19

Frame clearance ............................................................................. 20

Dimensional data for hardware ...................................................... 21

Application diagram ....................................................................... 22

Hardware overview Explanation on the hardware overview chapter ............................. 27

Tilt&Turn hardware – Basic security .............................................. 28

......................... 30

................ 32

Tilt-First hardware – Basic security ................................................ 34

Turn-Only hardware – Basic security .............................................. 36

Tilt-Only hardware – Basic security ................................................ 39

............................ 40

............ 44

....... 48

possible combinations .................................................................. 52

possible combinations .................................................................. 53

Profile-related components ............................................................ 54

General informationContents

4 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.

Installation Drilling the sash drill-holes ............................................................ 57

Install the handle ........................................................................... 59

Drilling the frame drill-holes .......................................................... 60

Cropping the hardware components .............................................. 62

Installing sash hardware components............................................ 63

Installing the turn-restrictor ........................................................... 64

Installing an additional scissor stay ............................................... 66

Connecting sash and frame ........................................................... 68

Installing the load transfer device .................................................. 70

Adjusting the load transfer device ................................................. 71

Installation drawings Positioning of the frame components ........................................... 74

Jigs ............................................................................................... 86

Adjustment Explanation on the adjustment chapter .......................................... 88

Adjustment instructions ................................................................ 89

Operation Operating information .................................................................... 92

Operation information for end-users .............................................. 93

Troubleshooting ............................................................................ 94

Maintenance Maintenance .................................................................................. 96

Lubrication points .......................................................................... 97

Inspection and care ....................................................................... 98

Preservation of the surface finish .................................................. 99

Dismantling Unhinging the sash with load transfer device .............................. 101

Unhinging the sash without load transfer device ......................... 102

Transport Transport, packaging, storage ..................................................... 103

Transport inspection .................................................................... 104

Disposal ................................................................................................... 105

General informationContents


General informationInformation on these instructions

This manual contains important information, instructions and application dia-

grams (maximum sash si es and sash weights) as well as installation instruc-

tions regarding the further work of the hardware.

Also, this manual contains binding guidelines to ensure the duty to instruct

through to the end-user.

The information and instructions in this manual refer to the products of the

Roto NT hardware system.

Apart from these installation, maintenance and operation instructions, the

following documents apply:

Catalogue

Directives of the Quality Assurance Association: Locks and Hardware

(Richtlinie der tegemeinschaft Schl sser und eschl ge e. .)

irectives H E of the uality ssurance ssociation ocks and Hardware

(Richtlinie H E der tegemeinschaft Schl sser und eschl ge e. .)

This manual should be stored in such a manner that it can be quickly used, if

needed.

Additional markingsTo highlight handling directives, results, lists, references and other elements,

the following signs are used in this manual:

Marking Explanation

Sash

Frame

Drill-holes

1 Hardware components

1. Action steps

First level of the hierarchy in a list

– nordered list (second level of hierarchy)

P. 12 (Cross) reference in tables

Refer to page 12 (Cross) reference in the text

Abbreviation Explanation

SRW Sash rebate width

SRH Sash rebate height

S.kg Sash weight

Resistance Class 1

Resistance Class 2

All dimensions stated in mm.

Protection of copyrightThe contents of this manual are protected by copyright. In the framework of

the hardware manufacturing, the use of the contents is allowed. Any other or

further use is not permitted without written permission of the manufacturer.


The information in this document is aimed at the following target groups:

Hardware dealersThe “hardware dealers” target group includes all companies/persons who

purchase hardware from the hardware manufacturer to resell it without the

hardware being modified or subjected to further work.

Manufacturers of windows and balcony doorsThe “manufacturers of windows and balcony doors” target group includes all

companies/persons who purchase hardware from the hardware manufac-

turer or the hardware dealer and build it into windows and balcony doors.

The “building element dealers” target group includes all companies/persons

who purchase windows and balcony doors from the manufacturer of windows

and balcony doors in order to sell these on and to install them into a building

development, without the windows or balcony doors being modified.

The “installation company” target group includes all companies/persons who

purchase windows and balcony doors from the manufacturer of windows and

balcony doors, or from a building element dealer, in order to sell these and to

install them into a building development, without the windows or balcony

doors being modified.

BuilderThe “builder” target group includes all companies/persons who order win-

dows and/or balcony doors for installation into their building project.

End-usersThe “end-users” target group includes all persons who operate the installed

windows and/or balcony doors.

General informationResponsibility of the target groups


General informationInstruction obligation of the target groups

NOTE!Every target group must fully comply with its instruction obligation.

Unless defined otherwise in the following, the documents and infor-

mation may be transmitted e.g. as printed documents, CD-ROM, or

via Internet access.

Responsibility of the hardware dealerThe hardware dealer must transmit the following documents to the manufac-

turer of windows and balcony doors:

– Catalogue

– Installation, maintenance and operation instructions

– irective for fixing load bearing urn Only and ilt urn hardware compo-

nents ( )

– uidelines advice on the product and on liability ( H H)

– uidelines advice for end users ( H E)

Responsibility of the manufacturer of windows and balcony doorsThe manufacturer of windows and balcony doors must transmit the following

documents to the building element dealer or to the builder, even when a

subcontractor (installation company) is acting as an intermediary

– Installation, maintenance and operation instructions

– irective for fixing load bearing urn Only and ilt urn hardware

components ( )



He must ensure that the end-user is provided with the documents and

information intended for him, in printed format.

The building element dealer must transmit the following documents to the

builder, even when a subcontractor (installation company) is acting as an

intermediary:

– aintenance and operating instructions (with the focus on hardware)



Responsibility of the builderThe builder must transmit the following documents to the end-user:

– aintenance and operating instructions (with the focus on hardware)



General informationExplanation of the safety instruction symbols

In this manual, safety information is indicated by symbols. The safety informa-

tion is introduced by a key word that indicates the severity of the danger.

DANGER!This symbol in conjunction with the signal word indicates an immi-

nently hazardous situation, which could result in death or serious

damage to health if it is not avoided.

WARNING!This symbol in conjunction with the signal word indicates a poten-

tially dangerous situation, which could result in death or serious

damage to health if it is not avoided.

CAUTION!This symbol in conjunction with the signal word indicates a poten-

tially dangerous situation, which may lead to minor or light injuries

if it is not avoided.

NOTE!This symbol in conjunction with the signal word indicates a poten-

tially dangerous situation, which may lead to property or environ-

mental damage if it is not avoided.


General informationLimitation of liability

All details and instructions in this document were compiled taking into ac-

count the relevant standards and regulations, the state of the art, and also

many years of knowledge and experience.

The hardware manufacturer accepts no liability for damages resulting from:

– Failure to comply with this document and all product-specific documents

and related applicable directives (refer to the chapters Safety and Stipu-

lated use).

– Non-stipulated use/misuse (refer to the chapters Safety and Stipulated

use).

– Insufficient invitation to tender, failure to adhere to the installation instruc-

tions or application drawings.

– Increased soiling.

Claims by third parties against the hardware manufacturer on the ground of

damages resulting from misuse or failure to follow the instruction obligation

on the part of the hardware dealer, the manufacturer of windows and bal-

cony doors, and of the building element dealer or the builder are transferred

accordingly.

The undertakings agreed in the delivery contract, the general conditions of

business and the delivery conditions of the hardware manufacturer, and the

legal regulations applicable at the time of concluding a contract are effective.

The warranty covers only original Roto components.

The right to technical modifications for the improvement of performance

characteristics and for further development is reserved.


SafetyStipulated use

urn Only and ilt urn hardware is one hand operation urn Only and

ilt urn hardware for windows and balcony doors in building construction.

This is used to enable windows and balcony-door sashes into a turning posi-

tion by operating a hand lever (handle) or into a limited tilting position in the

case of the scissors (sash stay) version. urn Only and ilt urn hardware is

used on vertically installed windows and balcony doors made of timber, C,

aluminium or steel and their corresponding material combinations. Turn-Only

and ilt urn hardware as covered by this definition, locks window and bal-

cony door sashes or enables various ventilating positions. When closing, the

gasket counter force must be overcome as a rule.

Correct use also includes adhering to all the specifications in the product-spe-

cific documents, such as:

– These installation, maintenance and operation instructions

– Product catalogues

– Information and specifications of the profile manufacturer (e.g. C or

light metal profiles etc.)

– he relevant directives and H E of the uality ssurance

Association: Locks and Hardware (Gütegemeinschaft Schlösser und

eschl ge e. .)

– The valid national laws and directives

Any type of use that goes beyond or differs from the defined correct use shall

be regarded as misuse.

WARNING!Danger from misuse!Misuse and incorrect installation of hardware can result in hazard-

ous situations.

– Never use hardware combinations that have not been approved

by the hardware manufacturer.

– Never use accessories that are not original products or that have

not been approved by the hardware manufacturer.


SafetyStipulated application for end-usersurn Only and ilt urn hardware

or windows and balcony doors with urn Only and ilt urn hardware, win-

dow and balcony door sashes can be brought into a turn position or into

a limited tilting position by means of the scissor stay.

When a sash is closed and the hardware is locked, the resistance of a gasket

usually needs to be overcome.

WARNING!Danger of injury and material damage from incorrect closing and opening the sash!Incorrect closing and opening of sashes can result in serious injuries

and significant material damage.

Therefore:

– Ensure that when closing the sash, it does not collide with the

frame or with another sash.

– Ensure that the sash is guided slowly by hand throughout the

entire range of movement as far as the fully closed position, and

that it is brought very slowly towards the frame.

– Ensure that the sash never slams closed or swings open in an

uncontrolled manner.

Any use beyond or other than the stipulated application and installation of

the products is deemed to be misuse and can result in dangerous circum-

stances.

WARNING!Danger from misuse!Misuse of windows and balcony doors can result in dangerous

circumstances.

In particular, avoid the following applications:

– insertion of obstacles in the opening area between the frame

and the window or balcony door sashes,

– the deliberate or negligent application of excessive loads on

windows and balcony doors,

– deliberate or uncontrolled slamming or pushing of windows and

balcony doors against the window reveal. This can destroy the

hardware, frame materials, or other individual components of

the windows or balcony doors.

Claims for damages of any type whatsoever resulting of operation other than

that stipulated are excluded.


SafetySafety instructionsurn Only and ilt urn hardware, Safety relevant symbols

Comply with the following symbols and their meanings in order to avoid

accidents, injuries and material damage.

Symbol Meaning

DANGER!Danger of injury from falling through open windows and balcony doors.– Proceed cautiously in the vicinity of open windows and balcony

doors.

– Please keep children and persons that cannot appreciate the

danger away from the hazard area.

WARNING!Danger of injury through trapping of body parts in the open-ing gap between sash and frame.– When closing windows and balcony doors, never reach between

sash and frame, and always act with care.

– Please keep children and persons that cannot appreciate the

danger away from the hazard area.

WARNING!Danger of injury and material damage from overloading the sash– Refrain from additionally loading the sash.

CAUTION!Danger of injury from the effect of wind– Prevent wind from acting on the open sash.

– During wind and draughts, close and lock windows and balcony

door sashes.

CAUTION!Danger of injury and material damage from insertion of ob-structions into the opening gap between sash and frame– Refrain from inserting obstacles in the opening gap between the

sash and the frame.

CAUTION!Danger of injury and material damage from pressing the sash

– o not press the sash against the opening edge (reveal).


SafetySafety information for end-users urn Only and ilt urn hardware, Safety relevant symbols

The following symbols can by used on windows and balcony doors to protect

the end-user. Always keep these symbols in a clearly legible state. Please

order stickers separately (O R 16 E EN v1).

SicherheitshinweisSecurity advice

08/2012 OPR_16_DE-EN_v1


SafetyFabrication advice

Maximum sash sizes and weightsThe technical data, application diagrams, and component classifications in

the product-specific documentation of the hardware manufacturer give in-

structions on the maximum permitted sash si es and weights. Here, the

component with the smallest permitted load bearing capacity decides the

maximum permitted sash weight.

– Check compliance of the technical data, application diagrams, and compo-

nent classifications before the use of electronic data sets, and especially

their use in fenestration programmes.

– he maximum permitted sash si es and weights must never be exceeded.

In the case of uncertainty contact the hardware manufacturer.

Guidelines from the profile manufacturerThe manufacturer of windows and/or balcony doors must comply with all

specified system-related dimensions (e.g. gasket gap dimensions or locking-

point distances). urthermore, he must check these regularly and make cer-

tain of them, especially on the first use of new hardware components, during

manufacture, in an ongoing manner up to and including the window installa-

tion.

NOTE!The hardware parts must always be designed such that the system-

related dimensions - insofar as they are affected by the hardware -

can be adjusted. If a deviation from these dimensions is noticed

only after the installation of the windows, the hardware manufac-

turer is not responsible for any possible additional work arising.

Composition of hardwareBurglary inhibiting windows and balcony doors require hardware which fulfils

particular requirements.

Windows and balcony doors for damp rooms, and those for use in environ-

ments with aggressive and corrosive air components require hardware which

fulfils particular requirements.

The resistance of windows and balcony doors to wind loads when closed

and locked depends on the actual designs of the windows and balcony

doors. Wind loads prescribed by law and standards (e.g. as per EN 12210 –

especially test pressure 3) can be dissipated by the hardware system.

In general, the urn Only and ilt urn hardware defined in this document is

able to fulfil legal and standard requirements for barrier-free habitations.

The hardware combinations and installations appropriate for windows and

balcony doors in the previously mentioned areas should be specifically se-

lected and agreed with the hardware manufacturer and the profile manufac-

turer.

NOTE!The guidelines of the hardware manufacturer relating to the combi-

nation of the hardware (e.g. the use of additional stay arms, the de-

sign of hardware for burglary-inhibiting sashes for windows and bal-

cony doors, etc.) are binding.


SafetyScrew fixing

DANGER!Danger to life from incorrectly installed and threaded hardware components!Incorrect installation and threading of hardware components can

result in dangerous circumstances and cause severe accidents,

even including death.

Therefore:

– For installation and especially for threaded components, observe

the product-specific documentation of the hardware manufacturer,

the information from the profile manufacturer, and all contents of

the TBDK directive of the Gütegemeinschaft Schlösser und

Beschläge.

or fixing the hardware components, Ø 3.9–4.2 x ... inc plated and passi-

vated steel fenestration screws are to be used. In the case of special climatic

conditions, use fenestration screws with additional sealing.

he window fabricator must ensure ade uate fixing of the hardware compo-

nents, consulting the screw manufacturer if necessary. When fixing security relevant, supportive hardware components such as stay bearings and

pivot rests, the tearing-forces vertical to the sash plane surface must be

reached in accordance with the following table (the tractive-force values

depend on the sash weights from the ).

Sash weight in kg Tractive force in N

60 1650

70 1900

80 2200

90 2450

100 2710

110 3000

120 3250

130 3525

140 3900

150 4200

1) Acceptable tolerance -10%

The stated values refer to the stay bearing. These are also valid for the pivot

rest if the fixing is carried out in the same manner as with the stay bearing.

On corrosive timber (i.e. af elia, oak etc.), the hardware s routed areas are to

be treated with a protective coating before installing the hardware in order to

protect the hardware.

Do not use any acid cross-linked sealing compounds that could lead to corro-

sion of the hardware components.

The glazing spacer-block regulations for the glazing procedure are to be

adhered to.


SafetyScrew fixing

Fixing suggestion installation of security windows

Screw fixing

Fixing SEC striker3 screws 4.0 x ...

Glazing-bead fixingor fixing the gla ing beads, use screws if re uired.

Screw fixing


Information on the productGeneral hardware characteristicsRoto N esigno urn Only ilt urn hardware system for windows and balcony doors

– Central locking system for one-hand-operation completely concealed in the

sash-rebate

– Profiled faceplate

– Effortless operation with low abrasion due to guided adjustable locking

cams

– Easy adjustment of the locking cams with standard tools

E cam gasket compression ad ustable eccentric cam and or

cam gasket compression ad ustable eccentric security cam and or

cam height and gasket compression ad ustable eccentric security cam

– Strong interlocking Clip it connection without loss of cam travel

– Link-slider guided stay arm, as standard with

– Integrated anti slam device (only version)

– Turn restriction

– ishandling device in tilted position (only version)

– Stay bearing and pivot rest completely concealed in the sash rebate

– High uality Roto Sil Nano surface finish (matt silvery) for maximum corro-

sion resistance ( IN EN 13126 8 Class 4) using Nano particles (free from

Chromium I compounds)

– 10-year warranty on the operativeness of the hardware

– 3D adjustment in stay arm / corner hinge / pivot rest

– Low-maintenance thanks to patented lubrication depots

– ested in accordance with EN 13126 – 8 2006–02 and EN 1191 2000 – 08

and certified according to 328

– Handles are available in different RAL colours

– With burglar-inhibiting anti-jemmy device in the tilt striker as standard

– Sash weights from 80 kg up to 150 kg thanks to load transfer component

– Long-term relieving of the pivot rest is ensured

– No jigs necessary for installation

– urn Only ilt urn sash

– Sash rebate width 330 – 1400 mm

– Sash rebate height 280 – 2600 mm

– Sash weight up to max. 150 kg

– Security levels acc. to IN EN 1627 1630

– Brands:

– Roto NT Designo or equivalent

* The application ranges are to be adhered according to the application diagrams


– Central locking system for one-hand-operation completely concealed in the

sash-rebate

– Profiled faceplate

– Effortless operation with low abrasion due to guided adjustable locking

cams

– Easy adjustment of the locking cams with standard tools

E cam gasket compression ad ustable eccentric cam and or

cam gasket compression ad ustable eccentric security cam and or

cam height and gasket compression ad ustable eccentric security cam

– Strong interlocking Clip it connection without loss of cam travel

– High uality Roto Sil Nano surface finish (matt silvery) for maximum corro-

sion resistance ( IN EN 1670 8 Class 5) using Nano particles (free from

Chromium I compounds)

– Rebate hinge with gasket-compression and clearance adjustment com-

pletely concealed in the sash rebate

– 10-year warranty on the operativeness of the hardware

– Low-maintenance

– ested in accordance with EN 13126 8 2006 02 and EN 1191 2000 08 and

certified according to 328

– Handles are available in different RAL colours

– Tilt-Only sash

– Sash rebate width 450 – 1400 mm

– Sash rebate height 370 – 1200 mm

– Sash weight up to max. 80 kg

– Handle height fixed, centred variable

– Security levels acc. to IN EN 1627–1630

– Brands:

Roto NT Designo or equivalent

* The application ranges are to be adhered according to the application diagrams.

Information on the productGeneral hardware characteristicsRoto NT Designo – Tilt-Only hardware for windows and balcony doors


Information on the productIntroduction

The surface-finish Roto Sil Nano surface-finish for ele-

gant matt silvery aesthetics. Unmis-

takable consistent silver look.

Optimal protection by means of gal-

vanising, chromating, and additional

sealing.

Increased corrosion protection.

The NT security concept The basic version of Roto NT is al-

ready equipped with basic security

on the bottom horizontal sash-plane.

Highest burglary inhibition results

are achieved with exemplary hard-

ware combinations for security win-

dows in accordance with

IN EN 1627–1630. his standard

includes an overall test of all individ-

ual window components.

Locking cam EGasket-compression adjustable cam

Locking cam PGasket-compression adjustable security mushroom cam

Locking cam VHeight and gasket-compression adjust-able security mush-room cam

The NT striker conceptAll strikers in the Roto NT hardware

system have identical screwing

axes.

This concept renders prefitting the

sash with security cams possible,

and a later frame retrofitting with se-

curity strikers ( inc or steel). ll lock-

ing cam versions are combinable

with all strikers.

Three locking cam versions The Roto NT hardware system offers

3 different locking cam versions that

differ in application and adjusting

capabilities.

The detailed adjusting dimensions

can be found in these installation

instructions.


Information on the productFrame clearance

H

B

A

X

Axis dimension A Overlap height H Overlap width B Frame clearance (O 90 ) X

13 16 18 5.2

13 20 18 7.6

13 24 18 10.6

13 16 20 4.9

13 20 20 7.2

13 24 20 9.9

13 16 22 4.7

13 20 22 6.8

13 24 22 9.3


Information on the productDimensional data for hardware

Hardware axis

18/20/22

12

24/3

0

13

Profile dimensionsSystem Euro rebate 12 18(20 22) 13

Rebate depth 24/30

Clearance, bottom hori ontal 11.5 – 14 mm

Clearance on the sides 10 – 14 mm

Clearance, top 11 – 14 mm

NOTE!The pivot rest of Designo is preset in the factory

to 12.5 mm clearance

9.4±0.2

2.2±0.2

16.2

+0.

2-0

.1

12.3

+0.

2-0

.1

13

18/20/22

Hardware axis

Hardware groove

Sash dimensions


Information on the productApplication diagramurn Only ilt urn hardware for rectangular windows 80 kg without load transfer device

Application diagramHinge side NT Designo

urn Only ilt urn hardware for rectangular windows 80 kg without

load transfer device

Limitation of sash formats depending on the glass thickness

Application rangeSash rebate width SRW ...........................330 – 1400 mm

Sash rebate height SRH ...........................280 – 2600 mm

Sash weight S.kg ............................................ max. 80 kg

The information in the application diagram refers

to the glass weight in kg m2.

1 mm m2 glass thickness 2.5 kg

= Impermissible application range

= Additional scissor stay required

2000

1000

2500

1500

500

1000500

50 k

g/m

2

40 k

g/m

2

30 k

g/m

2

20 k

g/m

2


Information on the productApplication diagramurn Only ilt urn hardware for rectangular windows 100 kg without load transfer device


urn Only ilt urn hardware for rectangular windows 100 kg without

load transfer device




Sash weight S.kg .......................................... max. 100 kg






2000

1000

2500

1500

500

1000500

50 k

g/m

2

40 k

g/m

2

30 k

g/m

2


Information on the productApplication diagramilt urn hardware rectangular windows with load transfer device from 80 – 150 kg


ilt urn hardware rectangular windows with load transfer device from

80 – 150 kg



Sash rebate height SRH .........................1000 – 2600 mm

Sash weight S.kg .................................. max. 80 – 150 kg






If the sash weight is 130 kg, set the stay arm s tilt restrictor to

80 mm.

2000

1000

1000

2500

1500

500

50060

kg

/m2

80 k

g/m

2

50 k

g/m

2

40 k

g/m

2


1000

1000

500550

500621

SRW in mm

SR

H in

mm

Information on the productApplication diagramTilt-Only hardware for rectangular windows


Tilt-Only hardware for rectangular windows


Application rangeSash rebate width SRW .............................450 – 1400 mm

Sash rebate height SRH .............................370 – 1200 mm

Sash weight S.kg .............................................max. 80 kg



1 mm/m2 glass thickness = 2.5 kg


= 2 tilt-stays laterally

= 1 tilt-stay on top

= 2 tilt-stays laterally or on top

= 2 tilt-stays on top


Hardware overviewExplanation on the hardware overview chapter

The hardware overviews on the following pages are recommendations of

Roto Frank AG.

The hardware overview chapter shows on the left page the single hardware

components in the hardware overview and on the right page the respective

parts list.

Position numbers in surrounding circles allow the allocation between hard-

ware overview and parts list.


Hardware overviewTilt&Turn hardware – Basic securityHardware overview

6)

3)

On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm

(see page 69).

1

2

3

4

5

6

21

21

21

21

21

8

911

14

22

23

20

15

19

18

10

13

7

24

17

12

16

25

6


Hardware overview Tilt&Turn hardware – Basic securityParts list

Application rangeSash rebate width SRW .................... 3301) – 14003) mm

Sash rebate width with load transfer ...... 525 – 14003) mm

Sash rebate height SRH ......................2802)6) – 26004) mm

Sash rebate height with load transfer ... 1000 – 26004) mm

Sash weight without load transfer ........... max. 100 kg

Sash weight with load transfer ................. max. 150 kg

1 T&T espagnolette, fixed handle height, backset 15 mm9)

SRH / mm Handle height / mm Espagnolette length Material no.

280 – 360 5),6),7),8) 120 370 284314

361 – 480 5),7) 120 370 284314

481 – 600 170 490 259830

601 – 800 263 690 259831

801 – 1000 413 890 259834

1001 – 1200 513 1090 1 E 259838

1201 – 1400 563 1290 1 E 259840

1401 – 1600 563 1490 1 E 259842

1601 – 1800 563 1690 2 E 259846

1601 – 1800 1000 1690 2 E 259847

1801 – 2000 1000 1890 2 E 259849

2001 – 2200 1000 2090 2 E 259851

2201 – 2400 1000 2290 2 E 259854

2401 – 2600 4) 1000 2290 3 E 259855

2 T&T espagnolette, centred/variable handle height, backset 15 mm9)


310 – 450 6),7),8) 155 – 225 430 259717

451 – 620 7) 225 – 310 400 259718

621 – 800 311 – 400 580 1 E 259719

801 – 1200 401 – 600 980 1 E 259720

1201 – 1600 601 – 800 1380 2 E 259721

1601 – 2000 801 – 1000 1780 2 E 259762

2001 – 2400 1001 – 1200 2180 4 E 259763

2401 – 2600 4) 1001 – 1200 2180 4 E 259763

3 Centre lock (from SRH 2401 mm)SRH / mm Size Material no.

2401 – 2600 200 CON 308267

4 Bullet catch cam 256020

5 Lifting mishandling device, sash component 260538

6 Corner drive not dep. E 260275

Corner drive P 260277

7 Corner drive, T&T P 260290

8 Special corner drive not dep. E 260280

(SRH < 360 or SRW < 430)

Special corner drive P 260282

(SRH < 360 or SRW < 430)

9 Stay guideSRW / mm Description Length Material no.

330 – 430 8) 250 490 385393

431 – 600 250 490 385393

601 – 800 350 690 385394

801 – 1000 500 890 1 E 385415

1001 – 1200 500 1090 1 E 385416

1201 – 1400 3) 500 1090 1 E 385416

10 Stay arm p. 56

11 Stay corner drive 6) P 260286

12 Corner hinge 634705

13 Pivot rest p. 56

14 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)

SRH / mm with load transfer (≥ 80 kg)

Size Material no.

1101 – 1150 400 1 E 255280

1101 – 1800 1151 – 1800 600 1 E 255281

1801 – 2400 1801 – 2400 600 CON 1 E 255282

600 1 E 255281

2401 – 2600 2401 – 2600 600 CON 1 E 255282

600 CON 1 E 255282

400 1 E 255280

15 Multipart centre lock, horizontalSRW / mm Size Material no.

1101 – 1400 600 1 E 255281

16 Additional scissor stay (from SRW 1201) 255237

17 Turn-restrictor, sash component 485591

(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)

18 Load transfer device, sash component 567972

19 Load transfer device, frame component 565254

Profile-related frame components: p. 54

20 Tilt striker

21 Striker

22 Bullet catch

23 Lifting mishandling device, frame component

24 Turn-restrictor, frame component


25 Night-vent, as an option

1) SRW 330 – 430 mm from SRH 361 mm2) SRH 280 – 361 mm from SRW 431 mm3) Use an additional scissor stay from SRW 1201 mm

4) From SRH 2401 mm CL 200 CON 3

5) With integrated corner drive6) SRH 280 – 330 mm: Shorten stay corner drive with completely extended connecting rod7) Not possible in combination with a lifting mishandling device8) With special corner drive9) Please refer to CTL_6 for further backsets

NOTE!Installation instructions for frame components

see page 74 – 75.

The actual scope of delivery depends on the ordered hardware configuration

(height and width of the window).


Hardware overviewTilt&Turn hardware – Basic securityHardware overview

6)

3)


(see page 69).

1

2

3

4

5

6

21

21

21

21

21

8

911

14

22

23

20

15

19

18

10

13

7

24

17

12

16

25

6


Hardware overview Tilt&Turn hardware – Basic securityParts list

Application rangeSash rebate width SRW ....................... 3301) – 14003) mm


Sash rebate height SRH ......................2802)6) – 26004) mm






280 – 360 5),6),7),8) 120 370 284314

361 – 480 5),7) 120 370 284314

481 – 600 170 490 259830

601 – 800 263 690 259831

801 – 1000 413 890 259834

1001 – 1200 513 1090 1 E 259838

1201 – 1400 563 1290 1 E 259840

1401 – 1600 563 1490 1 E 259842

1601 – 1800 563 1690 2 E 259846

1601 – 1800 1000 1690 2 E 259847

1801 – 2000 1000 1890 2 E 259849

2001 – 2200 1000 2090 2 E 259851

2201 – 2400 1000 2290 2 E 259854

2401 – 2600 4) 1000 2290 3 E 259855

2 backset 15 mm9)


310 – 450 6),7),8) 155 – 225 430 259717

451 – 620 7) 225 – 310 400 259718

621 – 800 311 – 400 580 1 E 259719

801 – 1200 401 – 600 980 1 E 259720

1201 – 1600 601 – 800 1380 2 E 259721

1601 – 2000 801 – 1000 1780 2 E 259762

2001 – 2400 1001 – 1200 2180 4 E 259763

2401 – 2600 4) 1001 – 1200 2180 4 E 259763


2401 – 2600 200 CON 308267






8 Special corner drive not dep. E 260280

(SRH < 360 or SRW < 430)


(SRH < 360 or SRW < 430)


330 – 430 8) 250 490 385393

431 – 600 250 490 385393

601 – 800 350 690 385394

801 – 1000 500 890 1 E 385415

1001 – 1200 500 1090 1 E 385416

1201 – 1400 3) 500 1090 1 E 385416

10 Stay arm p. 56

11 Stay corner drive P 260286


13 Pivot rest p. 56



Size Material no.

1101 – 1150 400 1 E 255280

1101 – 1800 1151 – 1800 600 1 E 255281

1801 – 2400 1801 – 2400 600 CON 1 E 255282

600 1 E 255281

2401 – 2600 2401 – 2600 600 CON 1 E 255282

600 CON 1 E 255282

400 1 E 255280


1101 – 1400 600 1 E 255281






p. 54

20 Tilt striker

21 Striker

22 Bullet catch





1) SRW 330 – 430 mm from SRH 361 mm2) SRH 280 – 361 mm from SRW 431 mm3) Use an additional scissor stay from SRW 1201 mm




see page 74 – 75.


4)

Hardware overview

Hardware overview

1)


(see page 69).

118

5

8

2

23

23

10

9

6

7

11

14

26

24

25

15

22

22

4

6

132321

17

12

16

20

19

3

27


Application rangeSash rebate width SRW ......................... 450 – 14001) mm


Sash rebate height SRH ....................... 2804) – 26002) mm


Hardware overview

Parts list



280 – 360 3),4),5),6) 120 370 284314

361 – 480 3),6) 120 370 284314

481 – 600 170 490 259830

601 – 800 263 690 259831

801 – 1000 413 890 259834

1001 – 1200 513 1090 1 E 259838

1201 – 1400 563 1290 1 E 259840

1401 – 1600 563 1490 1 E 259842

1601 – 1800 563 1690 2 E 259846

1601 – 1800 1000 1690 2 E 259847

1801 – 2000 1000 1890 2 E 259849

2001 – 2200 1000 2090 2 E 259851

2201 – 2400 1000 2290 2 E 259854

2401 – 2600 2) 1000 2290 3 E 259855

2 backset 15 mm7)


310 – 450 4),5),6) 155 – 225 430 259717

451 – 620 5) 225 – 310 400 259718

621 – 800 311 – 400 580 1 E 259719

801 – 1200 401 – 600 980 1 E 259720

1201 – 1600 601 – 800 1380 2 E 259721

1601 – 2000 801 – 1000 1780 2 E 259762

2001 – 2400 1001 – 1200 2180 4 E 259763

2401 – 2600 2) 1001 – 1200 2180 4 E 259763


2401 – 2600 200 CON 308267



6 Corner drive P 260277


8 Special corner drive (SRH < 360) P 260282


450 – 600 250 490 385393

601 – 800 350 690 385394

801 – 1000 500 890 1 E 385415

1001 – 1200 500 1090 1 E 385416

1201 – 1400 1) 500 1090 1 E 385416

10 Stay arm p. 56



13 Pivot rest p. 56



Size Material no.

1101 – 1150 400 1 E 255280

1101 – 1800 1151 – 1800 600 1 E 255281

1801 – 2400 1801 – 2400 600 CON 1 E 255282

600 1 E 255281

2401 – 2600 2401 – 2600 600 CON 1 E 255282

600 CON 1 E 255282

400 1 E 255284

15 Multipart centre lock, horizontalSRW / mm w/o turn-restrictor

SRW / mm with turn-restrictor

Size Material no.

450 – 650 650 – 850 200 1 P 255284

651 – 850 851 – 1050 400 1 P 255285

851 – 1000 1051 – 1250 600 1 P 255286

1251 – 1400 600 CON 1 E 255282

200 1 P 255284




18 Drilling protection 627343



p. 54

21 Tilt striker

22 Striker

23 Security striker

24 Bullet catch





1) Use an additional scissor stay from SRW 1201 mm






see page 76 – 77.


Hardware overview

Hardware overview


(see page 69).

1)

1)

1

173

21

21

9

8

6

10

13

24

22

23

14

21

21

21

21

4

5

122120

11

15

1619

18

25

2

5

7


Application rangeSash rebate width SRW ..........................450 – 14001) mm



Sash rebate height with load transfer ....1000 – 2400 mm



Hardware overview

Parts list



490 – 600 170 490 259830

601 – 800 263 690 1 259832

801 – 1000 413 890 2 259835

1001 – 1200 513 1090 2 259837

1201 – 1400 563 1290 2 259839

1201 – 1600 563 1490 3 259841

1601 – 1800 563 1690 3 259844

1601 – 1800 1000 1690 3 259845

1801 – 2000 1000 1890 3 259848

2001 – 2200 1000 2090 4 259850

2201 – 2400 1000 2290 4 259853

2 backset 15 mmSRH / mm Handle height / mm Espagnolette length Material no.

490 – 620 245 – 310 400 2597183),4)

621 – 800 311 – 400 580 1 355743

801 – 1200 401 – 600 980 1 355744

1201 – 1600 601 – 800 1380 2 355745

1601 – 2000 801 – 1000 1780 2 355746

2001 – 2400 1001 – 1200 2180 4 355747



5 Corner drive 260272

6 Corner drive, T&T 260288

7 Corner drive RC3 260274

8 Security stay guideSRW / mm Description Length Material no.

450 – 600 250 490 385393

601 – 800 350 690 385394

801 – 1000 500 890 1 450373

1001 – 1200 500 1090 1 450374

1201 – 1400 1) 500 1090 1 450374

9 Stay arm p. 56

10 Stay corner drive 260284


12 Pivot rest p. 56



Size Material no.

490 – 650 200 1 296853

651 – 850 1000 – 1150 400 1 296854

851 – 1050 1151 – 1350 600 1 2968555),8)

1051 – 1250 1351 – 1550 600 CON 1 337711

200 1 296853

1251 – 1450 1551 – 1750 600 CON 1 337711

400 1 296854

1451 – 1650 1751 – 1950 600 CON 1 337711

600 1 2968556),9)



Size Material no.

1651 – 1850 1951 – 2150 600 CON 1 337711

600 CON 1 337711

200 1 296853

1851 – 2050 2151 – 2350 600 CON 1 337711

600 CON 1 337711

400 1 296854

2051 – 2250 2351 – 2400 600 CON 1 337711

600 CON 1 337711

600 1 2968557),10)

2251 – 2400 600 CON 1 337711

600 CON 1 337711

600 CON 1 337711

200 1 296853

14 Multipart centre lock, horizontalSRW / mm w/o turn restrictor


Size Material no.

450 – 650 650 – 850 200 1 296853

651 – 850 851 – 1050 400 1 296854

851 – 1000 1051 – 1250 600 1 296855

1251 – 1400 600 CON 1 337711

200 1 296853







p. 54

20 Tilt striker

21 Security striker

22 Bullet catch





1) Use an additional scissor stay from SRW 1201 mm2) Please refer to CTL_6 for further backsets3) Not possible in combination with a lifting mishandling device

4) With corner drive RC3 7 bottom) Cut CL 1 mm up to SRW 861 mm

6) Cut CL 1 mm up to SRW 1461 mm7) Cut CL 1 mm up to SRW 2061 mm8) When using load transfer device cut CL 1 mm on SRH 11 1 mm9) When using load transfer device cut CL 1 mm on SRH 17 1 mm10) When using load transfer device cut CL 1 mm on SRH 23 1 mm


see page 78.



(see page 69).

4)4)

Hardware overviewTilt-First hardware – Basic securityHardware overview

1)

1

2

4

21

21

10

9

7

11

14

24

22

23

15

21

6

21

5

6

3 8

1321

17

20

12

16

19

18








Hardware overviewTilt-First hardware – Basic securityParts list

10 Stay arm Tilt-First p. 56

16 Additional scissor stay Tilt-First (from SRW 1201) 292022

p. 54

20 Tilt striker Tilt-First

1) Use an additional scissor stay from SRW 1201 mm


see page 74 – 75.

NOTE!For hardware components shown greyed out,

please refer to the Basic security chapter

ilt urn hardware, page 29.


3)

3)

Hardware overviewTurn-Only hardware – Basic securityHardware overview

1

18

4

8

2

18

19

1013

18

6

7

9

14

22

20

21

5

13

3

6

121817

16

15

11


Application rangeSash rebate width SRW ......................... 3703) – 1400 mm

Sash rebate height SRH ..........................280 – 26001) mm

Sash weight ................................................... max. 100 kg

Hardware overviewTurn-Only hardware – Basic securityParts list



280 – 360 2),4),5) 120 370 284314

361 – 480 2),4) 120 370 284314

481 – 600 170 490 259830

601 – 800 263 690 259831

801 – 1000 413 890 259834

1001 – 1200 513 1090 1 E 259838

1201 – 1400 563 1290 1 E 259840

1401 – 1600 563 1490 2 E 259842

1601 – 1800 563 1690 2 E 259846

1601 – 1800 1000 1690 2 E 259847

1801 – 2000 1000 1890 2 E 259849

2001 – 2200 1000 2090 2 E 259851

2201 – 2400 1000 2290 2 E 259854

2401 – 2600 1) 1000 2290 3 E 259855

2 backset 15 mm6)


310 – 450 4),5) 155 – 225 430 259717

451 – 620 4) 225 – 310 400 259718

621 – 800 311 – 400 580 1 E 259719

801 – 1200 401 – 600 980 1 E 259720

1201 – 1600 601 – 800 1380 2 E 259721

1601 – 2000 801 – 1000 1780 2 E 259762

2001 – 2400 1001 – 1200 2180 4 E 259763

2401 – 2600 1) 1001 – 1200 2180 4 E 259763


2401 – 2600 200 CON 308267






8 Special corner drive E 260280

(SRH < 360 450)


(SRH < 360 450)

9 Sash-component for rebate hinge 477255

10 Rebate-hinge arm p. 56


12 Pivot rest p. 56


1101 – 1400 600 1 E 255281

14 Centre-closer, concealed, sash component 450984



16 90° travel restrictor 264603

p. 54

17 Security striker

18 Striker

19 Centre-closer, concealed, frame component7)

20 Bullet catch



(possible from SRW 525, mandatory from SRW 1000 mm)


2) With integrated corner drive3) SRW 370 – 410 mm: Shorten corner drive on top 4) Not possible in combination with a lifting mishandling device5) With special corner drive6) Please refer to CTL_6 for further backsets7) Put pressure-resistant packers between glass and frame in the area of the centre-closers


see page 80 – 81.


1) 1)

Hardware overviewTilt-Only hardware – Basic securityHardware overview

7 7

5

9

2

9 9 9

8

9

10

1

7

2

5

4 4

6

3 3


Application rangeSash rebate width SRW ......................... 4502) – 1400 mm

Sash rebate height SRH .......................3701),3) – 1200 mm

Sash weight ..................................................... max. 80 kg

Hardware overviewTilt-Only hardware – Basic securityParts list

1 backset 15 mm4)

SRW / mm Espagnolette length Material no.

451 – 620 400 259718

621 – 800 580 1 E 259719

801 – 1200 980 1 E 259720

1201 – 1400 1380 2 E 259721





5 Multipart centre lock, verticalSRH / mm Size Material no.

801 – 1200 400 1 E 255280


7 Tilt-stay set for faceplate mounting 482823

Screw for mounting on corner drive 567995

8 264603

p. 54

9 Striker

10 Centre-closer, concealed, frame component

1) SRH 370 – 410 mm: Shorten corner drive2) SRW 4 0 – 620 mm only from SRH 00 mm3) SRH 370 – 00 mm only from SRW 621 mm4) Please refer to CTL_6 for further backsets


see page 82.

NOTE!Installation of tilt-stay, cf. IMO_111

( 576).



(see page 69).

w/o centre post

Hardware overview

Hardware overview

NOTE!Please refer to page 43 for possible combina-

tions of corner drives in the case of low and

narrow sashes.

INSTALLATION ADVICEHinge in the passive sash with lever-operated

espagnolette in open position.

5)

1)

26

15

15

21

33 33

2727

29

3029 30

33

2

28

1717

19

19a23

18

18a

30 31 30

30

30

26

32 1425

13 13

15

5

1

4

6 6

88

77

6 6

20

1212

1122

1024

9

16



Sash rebate width with load transfer ..... 525 – 14001) mm

Sash rebate height SRH ......................... 370 – 26002) mm





SRH / mm Handle height / mm Handle length / mm Material no.

430 – 480 3),4) 120 370 284314

481 – 600 170 490 259830

601 – 800 263 690 259831

801 – 1000 413 890 259834

1001 – 1200 513 1090 1 E 259838

1201 – 1400 563 1290 1 E 259840

1401 – 1600 563 1490 1 E 259842

1601 – 1800 563 1690 2 E 259846

1601 – 1800 1000 1690 2 E 259847

1801 – 2000 1000 1890 2 E 259849

2001 – 2200 1000 2090 2 E 259852

2201 – 2400 1000 2290 2 E 259854

2401 – 2600 2) 1000 2290 3 E 259855

2 backset 15 mm7)


370 – 450 4) 155 – 225 430 259717

451 – 620 4) 225 – 310 400 259718

621 – 800 311 – 400 580 1 E 259719

801 – 1200 401 – 600 980 1 E 259720

1201 – 1600 601 – 800 1380 2 E 259721

1601 – 2000 801 – 1000 1780 2 E 259762

2001 – 2400 1001 – 1200 2180 4 E 259763

2401 – 2600 2) 1001 – 1200 2180 4 E 259763


2401 – 2600 200 CON 308267






8 Special corner drive E 260280

(SRW < 430 mm)


(SRW < 430 mm)


370 – 430 250 490 385393

431 – 600 250 490 385393

601 – 800 350 690 385394

801 – 1000 500 890 1 E 385415

1001 – 1200 500 1090 1 E 385416

1201 – 1400 1) 500 1090 1 E 385416

4 Stay arm p. 56



13 Pivot rest p. 56



Size Material no.

1101 – 1150 400 1 E 255280

1101 – 1800 1151 – 1800 600 1 E 255281

1801 – 2400 1801 – 2400 600 CON 1 E 255282

600 1 E 255281

2401 – 2600 2401 – 2600 600 CON 1 E 255282

600 CON 1 E 255282

400 1 E 255280


1100 – 1400 600 1 E 255281




Hardware overview

Parts list


Hardware overview

Parts list

18 Lever-operated espagnolette, fixed lever-height6)

SRH / mm Lever position Length Material no.

430 – 500 195 490 233408

501 – 600

601 – 800 335 690 233409

801 – 1000 490 890 233410

1001 – 1200 335 1090 233411

1201 – 1400 335 1290 233412

1401 – 1600 335 1490 233413

1601 – 1800 335 1690 296145

1801 – 2000 640 1890 296074

2001 – 2200 640 2090 296075

2201 – 2400 640 2290 296076

2401 – 2600 12) 640 2290 296076

18a Lever-operated espagnolette Plus, fixed lever-height15)

SRH / mm Lever position Length / mm Material no.

431 – 500 8) 195 490 623365

501 – 600 9)

431 – 600 233 490 62336610)

601 – 800 195 690 62336811)

601 – 800 195 690 62336711)

601 – 800 335 690 623369

801 – 1000 490 890 623371

801 – 1000 195 890 62337011)

1001 – 1200 335 1090 623372

1201 – 1400 335 1290 623373

1401 – 1600 335 1490 623374

1601 – 1800 335 1690 623375

1801 – 2000 640 1890 623376

2001 – 2200 640 2090 623377

2201 – 2400 640 2290 623378

2401 – 2600 12) 640 2290 623378

19 6)


370 – 520 225 – 300 400 233418

521 – 620 301 – 350 400 233418

621 – 650 393 – 407 680 233419

651 – 800 408 – 482 680 233419

801 – 1200 482 – 682 980 233420

1201 – 1600 448 – 648 1380 290912

1601 – 2000 680 – 880 1780 296146

2001 – 2400 880 – 1080 2180 296147

2401 – 2600 12) 1080 2180 296147

19a 15)


370 – 620 225 – 350 400 62337914)

621 – 800 393 – 482 680 623380

621 – 900 680 62338111)

801 – 1200 482 – 682 980 623382

901 – 1200 980 62338311)

1201 – 1600 448 – 658 1380 623384

1601 – 2000 680 – 890 1780 623385

2001 – 2400 880 – 1090 2180 623386

2401 – 2600 12) 1090 2180 623386


see page 83.

20 Bullet catch for lever-operated espagnolette 385031

21 Lifting mishandling device 257600

Stop for lever-operated espagnolette


23 Corner drive with security striker5) 313538





28 Run-up block 350402

p. 54

29 Tilt striker

30 Striker

31 Security striker

32 Centre-closer, concealed, frame component12)



1) Use an additional scissor stay from SRW 1201 mm 16


3) With integrated corner drive 1 4) Not possible in combination with a lifting mishandling device) SRW 370 – 400 mm: Shorten corner drive on top

6) When using the lever operated espagnolette on the right hand side turn the eccentric cam 1807) Please refer to CTL_6 for further backsets8) With special corner drive 79) With corner drive 510) No striker possible11) For T T espagnolette 8 mm backset12) From SRH 2401 mm: centre lock CL 200 CON 313) Put pressure-resistant packers between glass and frame in the area of the centre-closers

14) Without lifting mishandling device (stop for lever-operated espagnolette)1 ) Lifting mishandling device (stop for lever operated espagnolette) preassembled as standard


Hardware overview

Combination possibilities: corner drives for low and narrow sashes

Fixed handle height, for low sashes

Material no. Material no.

SRH 430 – 500 8 260280260282

6 260275 Top

7 260290 7 260290 Bot-tom

Centred handle height, for low sashes


SRH 370 – 450 8 260280260282

8 260280260282

Top

8 260280260282

8 260280260282

Bot-tom

SRH 451 – 520 8 260280260282

6 260275 Top

8 260280260282

6 260275 Bot-tom

SRH 521 – 620 6 260275 6 260275 Top

6 260275 6 260275 Bot-tom

SRH 621 – 650 6 260280260282

6 260275 Top

8 260280260282

6 260275 Bot-tom

Centred handle height, for narrow sashes


SRW 370 – 400 23 313538 8 260280260282

Top

6 260275 6 260275 Bot-tom

SRW 401 – 430 23 313538 8 260280260282

Top

6 260275 6 260275 Bot-tom

Fixed handle height, for narrow sashes


SRW 370 – 400 23 313538 8 260280260282

Top

7 260290 7 260290 Bot-tom

SRW 401 – 430 23 313538 8 260280260282

Top

7 260290 7 260290 Bot-tom



(see page 69).

Hardware overview

Hardware overview

w/o centre post



1)

25

25

15 15

22

31 31

2626

28

3030

30

2

27

23

1717

19

19a

18

18a

30 30 30

30

2929

30

1414

13 13

24

5

1

4

6 6

88

77

6 6

20

1212

1111

1010

9

163 3

21




Sash rebate height SRH ......................... 370 – 26002) mm




Hardware overview

Parts list



430 – 480 3),4) 120 370 284314

481 – 600 170 490 259830

601 – 800 263 690 259831

801 – 1000 413 890 259834

1001 – 1200 513 1090 1 E 259838

1201 – 1400 563 1290 1 E 259840

1401 – 1600 563 1490 1 E 259842

1601 – 1800 563 1690 2 E 259846

1601 – 1800 1000 1690 2 E 259847

1801 – 2000 1000 1890 2 E 259849

2001 – 2200 1000 2090 2 E 259851

2201 – 2400 1000 2290 2 E 259854

2401 – 2600 2) 1000 2290 3 E 259855

2 backset 15 mm7)


370 – 450 4) 155 – 225 430 259717

451 – 620 4) 225 – 310 400 259718

621 – 800 311 – 400 580 1 E 259719

801 – 1200 401 – 600 980 1 E 259720

1201 – 1600 601 – 800 1380 2 E 259721

1601 – 2000 801 – 1000 1780 2 E 259762

2001 – 2400 1001 – 1200 2180 4 E 259763

2401 – 2600 2) 1001 – 1200 2180 4 E 259763


2401 – 2600 200 CON 308267



6 Corner drive P 260277


8 Special corner drive P 260282

(SRH < 480 mm) (not dep.)


450 – 600 250 490 385393

601 – 800 350 690 385394

801 – 1000 500 890 1 E 385415

1001 – 1200 500 1090 1 E 385416

1201 – 1400 1) 500 1090 1 E 385416

10 Stay arm p. 56

11 Stay corner drive (SRH 370 – 2600 mm) P 260286


13 Pivot rest p. 56



Size Material no.

1001 – 1150 400 1 E 255280

1101 – 1800 1151 – 1800 600 1 E 255281

1801 – 2400 1801 – 2400 600 CON 1 E 255282

600 1 E 255281

2401 – 2600 2401 – 2600 600 CON 1 E 255282

600 CON 1 E 255282

400 1 E 255280

15 Multipart centre lock, horizontalSRW / mm w/o turn-restrictor


Size Material no.

450 – 650 650 – 850 200 1 P 255284

651 – 850 851 – 1050 400 1 P 255285

851 – 1000 1051 – 1250 600 1 P 255286

1251 – 1400 600 CON 1 E 255282

1251 – 1400 200 1 P 255284







430 – 500 5) 195 490 233408

501 – 600

601 – 800 335 690 233409

801 – 1000 490 890 233410

1001 – 1200 335 1090 233411

1201 – 1400 335 1290 233412

1401 – 1600 335 1490 233413

1601 – 1800 335 1690 296145

1801 – 2000 640 1890 296074

2001 – 2200 640 2090 296075

2201 – 2400 640 2290 296076

2401 – 2600 2) 640 2290 296076



431 – 500 5) 195 490 623365

501 – 600 8)

431 – 600 233 490 6233669)

601 – 800 195 690 62336810)

601 – 800 195 690 62336710)

601 – 800 335 690 623369

801 – 1000 490 890 623371

801 – 1000 195 890 62337010)

1001 – 1200 335 1090 623372

1201 – 1400 335 1290 623373

1401 – 1600 335 1490 623374

1601 – 1800 335 1690 623375

1801 – 2000 640 1890 623376

2001 – 2200 640 2090 623377

2201 – 2400 640 2290 623378

2401 – 2600 2) 640 2290 623378

19 6)


370 – 520 5) 225 – 300 400 2334182)

521 – 620 301 – 350 400 2334182)

621 – 650 5) 393 – 407 680 233419

651 – 800 408 – 482 680 233419

801 – 1200 482 – 682 980 233420

1201 – 1600 448 – 648 1380 290912

1601 – 2000 680 – 880 1780 296146

2001 – 2400 880 – 1080 2180 296147

2401 – 2600 2) 880 – 1080 2180 296147

19a 6)


370 – 620 225 – 350 400 6233799)

621 – 800 393 – 482 680 623380

621 – 900 680 62338110)

801 – 1200 482 – 682 980 623382

901 – 1200 980 62338310)

1201 – 1600 448 – 658 1380 623384

1601 – 2000 680 – 890 1780 623385

2001 – 2400 880 – 1090 2180 623386

2401 – 2600 2) 1090 2180 623386

Hardware overview

Parts list


see page 84.





23 Turn-Only stay guideSRW / mm Description Length Material no.

450 – 510 250 490 482571

511 – 1400 11) 250 600 473381

24 Centre lock, connectable, horizontal, top, TU-ONSRW / mm Size Material no.

711 – 910 200 CON 308267

911 – 1110 400 CON 1 E 280346

1111 – 1310 600 CON 1 E 255282

1311 – 1400 600 CON 1 E 255282

200 CON 308267




p. 54

28 Tilt striker

29 Striker

30 Security striker



1) Use an additional scissor stay from SRW 1201 mm 16


3) With integrated corner drive4) Not possible in combination with a lifting mishandling device5) With special corner drive 7 6) When using the lever operated espagnolette on the right hand side turn the eccentric cam 1807) Please refer to CTL_6 for further backsets8) With corner drive 59) Without lifting mishandling device (stop for lever-operated espagnolette)10) For T T espagnolette 8 mm backset11) From SRW 711 mm: connectable centre lock 24

12) Lifting mishandling device (stop for lever operated espagnolette) preassembled as standard



(see page 69).

Hardware overview

Hardware overview

w/o centre post



1)

2626

14

14

21

31 31

2727

29

3030

30

22

28

24

1616

19

1717a

30 30 30

30

3030

30

1313

12 12

25

20

1

3

4 4

55

23

1111

1010

99

8

15

64

2

1818a

7

4








Hardware overview

Parts list



490 – 900 170 490 259830

601 – 800 263 690 1 259832

801 – 1000 413 890 2 259835

1001 – 1200 513 1090 2 259837

1201 – 1400 563 1290 2 259839

1401 – 1600 563 1490 3 259841

1601 – 1800 563 1690 3 259844

1601 – 1800 1000 1690 3 259845

1801 – 2000 1000 1890 3 259848

2001 – 2200 1000 2090 4 259850

2201 – 2400 1000 2290 4 259853

2 backset 15 mmSRH / mm Handle height / mm Espagnolette length Material no.

490 – 620 245 – 310 400 2597189),10)

621 – 800 311 – 400 580 1 355743

801 – 1200 401 – 600 980 1 355744

1201 – 1600 601 – 800 1380 2 355745

1601 – 2000 801 – 1000 1780 2 355746

2001 – 2400 1001 – 1200 2180 4 355747


4 Corner drive 260272

5 Corner drive, T&T 260288

6 Corner drive RC3 2 260274

7 1 367227


450 – 600 250 490 385393

601 – 800 350 690 385394

801 – 1000 500 890 1 450373

1001 – 1200 500 1090 1 450374

1201 – 1400 1) 500 1090 1 450374

9 Stay arm p. 56

10 Stay corner drive (SRH 490 – 2400 mm) 260286


12 Pivot rest p. 56



Size Material no.

490 – 650 200 1 296853

651 – 850 1000 – 1150 400 1 296854

851 – 1050 1151 – 1350 600 1 29685512),15)

1051 – 1250 1351 – 1550 600 CON 1 337711

200 1 296853

1251 – 1450 1551 – 1750 600 CON 1 337711

400 1 296854

1451 – 1650 1751 – 1950 600 CON 1 337711

600 1 29685513),16)

1651 – 1850 1951 – 2150 600 CON 1 337711

600 CON 1 337711

200 1 296853

1851 – 2050 2151 – 2350 600 CON 1 337711

600 CON 1 337711

400 1 296854

2050 – 2250 2351 – 2400 600 CON 1 337711

600 CON 1 337711

600 1 29685514),17)

2251 – 2400 600 CON 1 337711

600 CON 1 337711

600 CON 1 337711

200 1 296853

14 Multipart centre lock, horizontalSRW / mm w/o turn restrictor


Size Material no.

450 – 650 650 – 850 200 1 296853

651 – 850 851 – 1050 400 1 296854

851 – 1000 1051 – 1250 600 1 296855

1251 – 1400 600 CON 1 337711

200 1 296853







601 – 800 335 690 233409

801 – 1000 490 890 233410

1001 – 1200 335 1090 233411

1201 – 1400 335 1290 233412

1401 – 1600 335 1490 233413

1601 – 1800 335 1690 296145

1801 – 2000 640 1890 296074

2001 – 2200 640 2090 296075

2201 – 2400 640 2090 296076



600 – 800 195 690 6233685),6)

600 – 800 195 690 6233676)

600 – 800 335 690 623369

801 – 1000 490 890 623371

801 – 1000 195 890 6233706)

1001 – 1200 335 1090 623372

1201 – 1400 335 1290 623373

1401 – 1600 335 1490 623374

1601 – 1800 335 1690 623375

1801 – 2000 640 1890 623376

2001 – 2200 640 2090 623377

2201 – 2400 640 2290 623378

18 2)


520 – 650 301 – 350 400 23341811)

651 – 800 408 – 482 680 233419

801 – 1200 482 – 682 980 233420

1201 – 1600 448 – 648 1380 290912

1601 – 2000 680 – 880 1780 296146

2001 – 2400 880 – 1080 2180 296147

18a 4)


520 – 650 225 – 350 400 6233795)

651 – 800 393 – 482 680 623380

651 – 900 680 6233816)

801 – 1200 482 – 682 980 623382

901 – 1200 980 6233836)

1201 – 1600 448 – 658 1380 623384

1601 – 2000 680 – 890 1780 623385

2001 – 2400 880 – 1090 2180 623386

Hardware overview

Parts list


see page 85.






23 Retainer-clasp 314203

24 Turn-Only stay guideSRW / mm Description Length Material no.

450 – 510 250 490 482571

511 – 1400 8) 250 600 473381

25 Centre lock, connectable, horizontal, top, Turn-Only sashSRW / mm Size Material no.

711 – 910 200 CON 1 337708

911 – 1110 400 CON 1 337710

1111 – 1310 600 CON 1 337711

1311 – 1400 600 CON 1 337711

200 CON 1 337708




p. 54

29 Tilt striker

30 Security striker



1) Use an additional scissor stay from SRW 1201 mm2) When using the lever operated espagnolette on the right hand side turn the eccentric cam 1803) Please refer to CTL_6 for further backsets4) Lifting mishandling device (stop for lever operated espagnolette) preassembled as standard5) No striker possible6) For T T espagnolette 8 mm backset7) Not for lever-operated espagnolette Plus8) From SRW 711 mm: connectable centre lock 25

9) Not possible in combination with a lifting mishandling device

10) With corner drive RC3 6 bottom

11) With corner drive with welded-on striker 712) Cut CL 1 mm up to SRW 861 mm13) Cut CL 1 mm up to SRW 1461 mm14) Cut CL 1 mm up to SRW 2061 mm1 ) When using load transfer device cut CL 1 mm on SRH 11 1 mm16) When using load transfer device cut CL 1 mm on SRH 17 1 mm17) When using load transfer device cut CL 1 mm on SRH 23 1 mm


Hardware overview

SRH / mm Lever position / mm Length / mm Material no.

430 – 450 225 – 265 400 233418451 – 520 266 – 300 400 233418521 – 620 301 – 350 400 233418

621 – 650 393 – 407 680 233419

651 – 800 408 – 482 680 233419

801 – 1200 482 – 682 980 233420

1201 – 1600 448 – 648 1380 290912

1601 – 2000 680 – 880 1780 296146

2001 – 2400 880 – 1080 2180 296147

2401 – 2600 1080 2180 296147

(C 200) 308267

Lifting mish. device possible Handle height Length / mm Material no.

155 – 225 430 259717

226 – 310 400 259718

226 – 310 400 259718

X 311 – 400 580 259719

X 311 – 400 580 259719

X 401 – 600 980 259720

X 601 – 800 1380 259721

X 801 – 1000 1780 259762

X 1001 – 1200 2180 259763

X 1200 2180 259763

(C 200) 308267

Lever-operated espagnolette, fixed lever-heightSRH / mm Lever position / mm Length / mm Material no.

430 – 480 195 490 233408

481 – 500 195 490 233408

501 – 600 195 490 233408

601 – 800 335 690 233409

801 – 1000 490 890 233410

1001 – 1200 335 1090 233411

1201 – 1400 335 1290 233412

1401 – 1600 335 1490 233413

1601 – 1800 335 1690 296145

1601 – 1800 335 1690 296145

1801 – 2000 640 1890 296074

2001 – 2200 640 2090 296075

2201 – 2400 640 2290 296076

2401 – 2600 640 2290 296076

(C 200) 308267

T&T espagnolette, fixed handle heightLifting mish. device possible Handle height Length / mm Material no.

120 370 284314

X 170 490 259830

X 170 490 259830

X 263 690 259831

X 413 890 259834

X 513 1090 259838

X 563 1290 259840

X 563 1490 259842

X 563 1690 259846

X 1000 1690 259847

X 1000 1890 259849

X 1000 2090 259851

X 1000 2290 259854

X 1000 2290 259855

(C 200) 308267

SRH / mm Lever position / mm Length / mm Material no.

370 – 620 No lever-operated espagnolettes possible in this range

621 – 800 236 – 325 680 242726

801 – 900 325 – 375 680 242726

901 – 1200 298 – 448 980 242728

1201 – 1600 448 – 658 1380 290912

1601 – 2000 680 – 880 1780 296146

2001 – 2400 880 – 1080 2180 296147

2401 – 2600 1080 2180 296147

(C 200) 308267

Lifting mish. device possible Handle height Length / mm Material no.

311 – 400 580 259766

401 – 450 980 623646

X 451 – 600 980 623646

X 601 – 800 1380 259768

X 801 – 1000 1780 259769

X 1001 – 1200 2180 259770

X 1200 2180 259770

(C 200) 308267

Lever-operated espagnolette, fixed lever-heightSRH / mm Lever position / mm Length / mm Material no.

430 – 510 233 490 317047

511 – 600 233 490 317047

601 – 800 195 690 242730

801 – 1000 490 890 242732

1001 – 1200 335 1090 233411

1201 – 1400 335 1290 233412

1401 – 1600 335 1490 233413

1601 – 1800 335 1690 296145

1601 – 1800 335 1690 296145

1801 – 2000 640 1890 296074

2001 – 2200 640 2090 296075

2201 – 2400 640 2290 296076

2401 – 2600 640 2290 296076

(C 200) 308267

T&T espagnolette, fixed handle heightLifting mish. device possible Handle height Length / mm Material no.

170 490 259856

170 490 259856

X 263 690 259858

X 413 890 259861

X 513 1090 259865

X 563 1290 259867

X 563 1490 259869

X 563 1690 259873

X 1000 1690 259874

X 1000 1890 259876

X 1000 2090 259878

X 1000 2290 259881

X 1000 2290 259881

(C 200) 308267


Hardware overview

1) With special corner drive2) With integrated T&T corner drive with P cam3) Screwing position under the lever.

Lever-operated espagnolette, fixed lever-heightSRH / mm Length / mm Lever position / mm Material no.

431 – 480 490 195 623365 1)

481 – 500 490 195 623365 1)

501 – 600 490 195 623365601 – 800 690 335 623369801 – 1000 890 490 623371

1001 – 1200 1090 335 6233721201 – 1400 1290 335 6233731401 – 1600 1490 335 6233741601 – 1800 1690 335 6233751601 – 1800 1690 335 6233751801 – 2000 1890 640 6233762001 – 2200 2090 640 6233772201 – 2400 2290 640 6233782401 – 2600 2290 640 623378

(C 200) 450822

Lifting mish. device possible Length / mm Handle height Material no.

370 120 284314 2)

X 490 170 259830X 490 170 259830X 690 263 259833X 890 413 259836X 1090 513 259838X 1290 563 259840X 1490 563 259843X 1690 563 259846X 1690 1000 259847X 1890 1000 259849X 2090 1000 259852X 2290 1000 259855X 2290 1000 259855

(C 200) 450821


430 155 – 225 259717 1)

400 226 – 310 259718

400 226 – 310 259718

X 580 311 – 400 259719

X 580 311 – 400 259719

X 980 401 – 600 259720

X 1380 601 – 800 259721

X 1780 801 – 1000 259762

X 2180 1001 – 1200 259763

X 2180 1001 – 1200 259763

(C 200) 308267

SRH / mm Length / mm Lever position / mm Material no.

370 – 450 400 225 – 265 623379 1)3)

451 – 520 400 266 – 300 623379 1)3)

521 – 620 400 301 – 350 623379 3)

621 – 650 680 393 – 407 623380 1)

651 – 800 680 408 – 482 623380

801 – 1200 980 482 – 682 623382

1201 – 1600 1380 448 – 648 623384

1601 – 2000 1780 680 – 880 623385

2001 – 2400 2180 880 – 1080 623386

2401 – 2600 2180 1080 – 1280 623386

(C 200) 308267


490 170 259856 2)

490 170 259856 2)

690 263 259860X 890 413 259863X 1090 513 259865X 1290 563 259867X 1490 563 259870X 1690 563 259873X 1690 1000 259874X 1890 1000 259876X 2090 1000 259879X 2290 1000 259882X 2290 1000 259882

(C 200) 450821


431 – 510 490 233 623366 1)

511 – 600 490 233 623366601 – 800 690 195 623367 3)

801 – 1000 890 490 623370 3)

1001 – 1200 1090 335 6233721201 – 1400 1290 335 6233731401 – 1600 1490 335 6233741601 – 1800 1690 335 6233751601 – 1800 1690 335 6233751801 – 2000 1890 640 6233762001 – 2200 2090 640 6233772201 – 2400 2290 640 6233782401 – 2600 2290 640 623378

(C 200) 450822


580 311 – 400 259766980 401 – 450 623646

X 980 451 – 600 623646X 1380 601 – 800 259768X 1780 801 – 1000 259769X 2180 1001 – 1200 259770X 2180 1001 – 1200 259770

(C 200) 308267


621 – 800 680 236 – 325 623381 1)3)

801 – 900 680 325 – 375 623381 3)

901 – 1200 980 298 – 448 623383 3)

1201 – 1600 1380 448 – 658 6233841601 – 2000 1780 680 – 880 6233852001 – 2400 2180 880 – 1080 6233862401 – 2600 2180 1080 – 1280 623386

(C 200) 308267


Hardware overview Profile-related components

System HA Striker Tilt striker, zinc

Tilt striker, steel

TF tilt striker SEC striker, zinc

SEC striker, steel

mm Material no. Material no. Material no. Material no. Material no. Material no.

Euro rebate 24 mm 13.0 L 261943 632132 261935

13.0 R 262927 632133 262930

13.0 R 261933

Euro rebate 24 mm, with supporting-pins

13.0 L 261944 632132 261936

13.0 R 262929 632133 262931

13.0 R 261934

Euro groove 11 8, rebate depth 24 mm

13.0 L 378464 456956 378465

13.0 R 378457 456955 378466

13.0 R 378467

Euro rebate 30 mm 13.0 L 631525 602788

13.0 R 631526 602789

13.0 R 599651 602201 631527 602215


13.0 L 631502 602788

13.0 R 631504 602789

13.0 R 599652 602202 355611 602216

To be routed in, 25 mm rebate depth, 5 mm clearance

13.0 L 627988 627984 627988

13.0 R 627990 627986 627990



System HA Bullet catch Lift. mish. device Night-vent Turn-restrictor Centre-closer, concealed

frame component frame component frame component frame component sash component frame componentmm Material no. Material no. Material no. Material no. Material no. Material no.

24 mm Euro rebate 13.0 L 261945 491798

13.0 R 262932 491798

13.0 R 261941 261947 450984 606610

Euro rebate 24 mm with supporting-pins

13.0 L 261946 337754

13.0 R 262933 337754

13.0 R 261942 261948 450984 617516

Euro groove 11 8, 24 mm rebate depth

13.0 R 378469 383281 256584

Euro rebate 30 mm 13.0 R 578785 595679 491798 450984 606612


13.0 R 578786 337754 450984 606613

To be routed in, 25 mm rebate depth, 5 mm clearance

13.0 L 551744

13.0 R 551743


Profile Pivot rest Sash stay 250 Sash stay 350 Sash stay 500TF sash stay 250

TF sash stay 350

TF sash stay 500

Rebate hinge

Material no. Material no. Material no. Material no. Material no. Material no. Material no. Material no.

DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L

Euro-rebate

563736 563737 563728 563732 563729 563733 563730 563734 600801 600800 600803 600802 600805 600804 563731 563735

Euro-rebate

570079 570080 570050 570054 570051 570075 570052 570076 – – – – – – 570053 570077



Backset

Han

dle

heig

ht

dim

ensi

on H

H

10 mm, 33 mm deep

10 mm, 33 mm deep

18

43

Ø 25

15 Carry out the drillings for the window handle’s

sprocket and lugs.

Ø 10Ø 10

Ø 12

Drilling for the sash

Backset15

Ø 25

At

an o

verla

p he

ight

of

16 m

m

MillingEspagnolette gear-casing

InstallationDrilling the sash drill-holes


InstallationDrilling the sash drill-holes

46

62

92.5

152.

5 167.

5

337.

5

352.

5

35.8

108

Drilling for corner hinge and load transfer device


InstallationInstall the handle

Hardware groove

Espagnolette gear-casing

Threaded bevels

Screw fix the window handle in the main lock casing

with IN 965 5 x countersunk screws.

ugs, 10 mm

Spindle, 7 mm

52

Roto Swing window handlewith lugs and 7 mm spindle


32

24

56

11.5

17

2x Ø6

min

.10

3555

11.517

19.5

56

88

10

2x Ø6

11.5

17

32.5

24.5 47

.5

56.5

55

56

88

19.517

11.5 35

Reb

ate

de

pth

24 m

m

max

. R2

Rebate depth 24 mm

max. R2

depth

Rebate depth 24 mm

With load transfer device only for 80 kg sash weights

32

24

56

11.5

17

2x Ø6

min

.10

3555

11.517

19.5

56

8810

2x Ø6

11.5

17

32.5

24.5 47

.5

56.5

55

56

88

19.517

11.5 35

Reb

ate

de

pth

24 m

m

min

.

max

. R2

max. R2

InstallationDrilling the frame drill-holes


11.5

22.5

2x Ø6

min

. 10

3555

56

88

19.5

22.5

11.5

32

24

56

min

. 10

2 x Ø6

11.5

22.5

56

88

3555

19.5

11.5

22.5

17

32.5

24.5 47

.5

56.5

Reb

ate

de

pth

30 m

m

max

. R2

Rebate depth 30 mm

max. R2

depth

11.5

22.5

2x Ø6

min

. 10

3555

56

88

19.5

22.5

11.5

32

24

56

min

. 10

2 x Ø6

11.5

22.5

56

88

3555

19.5

11.5

22.5

17

32.5

24.5 47

.5

56.5

With load transfer device only for 80 kg sash weights

Rebate depth 30 mm

Reb

ate

de

pth

30 m

m

max

. R2

max. R2

InstallationDrilling the frame drill-holes


InstallationCropping the hardware components

Crop with pneumatic cropper (punched hole)Hole punchDescription Material no.

neumatic cropper S 100 (not dep.) DIN L 553992

DIN R 553993

Cropper with tool DIN L 262153

DIN R 262156


InstallationInstalling sash hardware components

1. Corner drive2. Corner drive, 3. espagnolette4. Stay corner drive5. Stay guide6. Centre lock, vertical and horizontal7. Corner hinge

7.

6.

6.

5.4.

3.

2.

1.


InstallationInstalling the turn-restrictor

32

95

104

Pivot restTurn-restrictor, frame component

Positioning of the turn-restrictor 90°

151

162.5

Turn-restrictor, sash component

Corner hinge

151

162.5

NOTE!The turn-restrictor is a

comfort component, not

a security component.

WARNING! The 90° embossing must

point towards the corner

hinge. Incorrect installation

of the turn-restrictor’s sash

component destroys the

pivot rest


32

95

104

Pivot restTurn-restrictor, frame component

Positioning of the turn-restrictor 90°

151

162.5

Turn-restrictor, sash component

Corner hinge

151

162.5

NOTE!The turn-restrictor is a

comfort component, not

a security component.

WARNING! The 90° embossing must

point towards the corner

hinge. Incorrect installation

of the turn-restrictor’s sash

component destroys the

pivot rest

Press the hole at the end of the sash component on the

rubber ring of the frame component’s bolt.

InstallationInstalling the turn-restrictor


417

200

Additional scissor stay Frame component

Additional scissor stay Sash component

Stay guide

Corner drive

CAUTION! If the additional scissor stay TF is used, a lifting mishandling device must be installed.

If the additional scissor stay TF is installed, the arrestable brake-stay and the multi-stepped night-vent cannot

be used.

Observe the installation dimensions for frame and sash component

InstallationInstalling an additional scissor stay


InstallationConnecting sash and frameSash stay 250, 350 and 500

Hinging the sash

1. Put the pivot rest into its original position

( closed sash position).2. Bring the handle into the turn mode.3. Run down the sash slightly tilted along the frame,

until the corner hinge meets the pivot rest.

4. Secure the sash from falling out.5. Press down the lifting mishandling device

(if mounted).6. Bring the handle into the tilt mode.

This is a conscious – and in this case necessary – hard-

ware mishandling operation!


InstallationConnecting sash and frameSash stay 250, 350 and 500

Tilt-depth regulator, tilt depth 140 mm (standard)

Entry tilt mode

7. Press down the stay arm on the stay guide and

supporting arm.

Retainer-clasp 8. Close the retainer-clasp.9. Operate again the lifting mishandling device and bring

the handle into the turn mode.

NOTE!se the anti slam device (487206) for 80 mm

tilt depth.

ilt depth 140 mm (standard)

Slider

180°

ilt depth 80 mm

Slider

7. Adjust the desired tilt depth

(Standard tilt depth 140 mm)

180°


180°

ilt depth 80 mm 8. Connect the slider of the sash stay with the stay

guide.

Slider s nal position = anti-slam device

Slider s nal position = anti-slam device

Hitching pin

Hitching pin


ilt depth 80 mm

9 Lift the sash stay arm and let the drilling-hole of

the sash stay arm snap on the hitching pin of the

supporting arm.10. Operate again the lifting mishandling device and bring

the handle into the turn mode.

NOTE!he slider s final position ( anti slam device) is

reached automatically by means of tilting the

sash.


InstallationInstalling the load transfer deviceGeneral advice

FunctionalityThe spring in the load transfer device disburdens the pivot rest permanently

by approx. 60 to 80 kg.

In order to do so, the spring must be pre-stretched to a certain length. This

applies regardless of the adjustment height of the sash.

The relieving of the pivot rest is carried out over the entire lifespan of the

hardware, also in consideration of sagging and wear and tear.

Installation adviceThe load transfer device’s spring can already be pre-stretched in the work-

shop, this however only makes sense if the sash is installed with the full glass

load.

Transport possibility 1Transport the sash and frame separately.

Transport possibility 2Transport the sash in the frame.

CAUTION! he bearing can buckle

Pre-stretch the load transfer device’s spring and support the frame

with spacers in the bottom rebate

UnhingingScrew out the screw of the load transfer device until the spring tension is re-

leased completely (support rod is loosened). If the tension in the spring is not

completely released, the sash cannot be hinged into the frame again.

Application restrictionso not e uip sashes with a sash weight < 80 kg with a load transfer device,

because this can result in malfunctions.


InstallationInstalling the load transfer device

2.

1.

3.

5.

6.

Functionality of the load transfer device

The spring in the load transfer device disburdens the

pivot rest permanently by approx. 60 to 80 kg.

In order to do so, the spring must be pre-stretched to

a certain length. This applies regardless of the adjust-

ment height of the sash.

The relieving of the pivot rest is carried out over the

entire lifespan of the hardware, also in consideration of

sagging and wear and tear.

NOTE!Do not equip sashes with a sash weight

< 80 kg with a load transfer device, because

this can result in malfunctions.

It is compulsory to use a turn-restrictor.

If the sash is already hinged in the frame prior

to transportation, the spring of the load trans-

fer can be clamped in the workshop. How-

ever, this is only sensible if the sash is assem-

bled with the full glass load.

Installing the load transfer device

1. Insert the load transfer device’s sash component

up against the corner hinge and screw fix.2. Loosen the pivot rest’s top screw connection.3. Place the load transfer device’s frame component

on top of the pivot rest and screw fix.4. Hinge the sash (see page 68).5. Connect the support rod with the sash component

and insert into the cavity of the frame component.

Adjusting the load transfer device

6. d ust the load transfer device with a 4 mm hex key

in a (90 ) opened sash position

Adjust the adjusting screw in the silver divided cir-

cle in such a manner that the sum of the red and

silver divided circles result in one complete circle.

Check the result in the inspection opening.

6.


Installation guidelineBurglar-resistant windows in accordance with DIN EN 1627–

1630 may only be named so, if the installation has been carried

out in all points in accordance with the specified standards.

Attach spacer blocks in the vicin-

ity of the screw fixings of the se-

curity strikers and the concealed

centre-closers.

Frame

Masonry brickwork

Spacer blocks

InstallationFixing suggestion installation of security windows


Installation drawingsPositioning of the frame components ilt urn and ilt irst – asic security

T&T espagnolette, fixed handle height Basic security

L Lifting mishandling device C ullet catch

76

58

50

149

12

95

58

T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 LMD C

280 – 480 120 – – – – –

481 – 600 170 – – – 223 –

601 – 800 263 – – – 138 –

801 – 1000 413 – – – 288 –

1001 – 1200 513 700 – – 388 –

1201 – 1400 563 700 – – 388 –

1401 – 1600 563 700 – – 388 –

1601 – 1800 563 700 1370 – 388 –

1601 – 1800 1000 700 1370 – 1121 1244

1801 – 2000 1000 700 1370 – 1121 1244

2001 – 2200 1000 700 1370 – 1121 1244

2201 – 2400 1000 700 1370 – 1121 1244

2401 – 2600 1000 700 1370 1770 1121 1244

Stay guideSRW / mm A Size

801 – 1000 600 500 / 890

1001 – 1200 750 500 / 1090

1201 – 1400 750 500 / 1090

Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3

1101 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E

Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3

1101 – 1150 550 – – – C 400 E

1151 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E

Centre lock, horizontalSRW / mm CLH1

1101 – 1400 658 CL 600 E

CLH1

Tilt striker

LMD

G3

G2

G1

HH

CL2

CL1

Turn-restrictor

p to SRW 430

rom SRW 431

BC

CL3

A


SRH / mm A B C D E LMD C

310 – 450 – – – – – – –

451 – 620 – – – – – –

621 – 800 125 – – – – 137 –

801 – 1200 125 – – – – 137 –

1201 – 1600 125 340 – – – 137 –

1601 – 2000 – 312 358 – – 109 232

2001 – 2400 – 312 358 758 740 109 232

2401 – 2600 – 312 358 758 740 109 232

76

58

50

BE

AC

D

Basic security

Tilt striker

BC

LMD

1)LMD

2)

Handle/centre


Installation drawingsPositioning of the frame components ilt urn and ilt irst – asic security


Installation drawingsPositioning of the frame componentsilt urn – RC1 N

T&T espagnolette, fixed handle height


58

12

149

86.576

95CLH1

Tilt striker

BC

LMD

G2

G1

HH

CL2

CL1

CLH2

A

Turn-restrictor

CL3

T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 LMD C

280 – 480 120 – – – – –

481 – 600 170 – – – 223 –

601 – 800 263 – – – 138 –

801 – 1000 413 – – – 288 –

1001 – 1200 513 700 – – 388 –

1201 – 1400 563 700 – – 388 –

1401 – 1600 563 700 – – 388 –

1601 – 1800 563 700 1370 – 388 –

1601 – 1800 1000 700 1370 – 1121 1244

1801 – 2000 1000 700 1370 – 1121 1244

2001 – 2200 1000 700 1370 – 1121 1244

2201 – 2400 1000 700 1370 – 1121 1244

2401 – 2600 1000 700 1370 1770 1121 1244


801 – 1000 600 500 / 890

1001 – 1200 750 500 / 1090

1201 – 1400 750 500 / 1090


1101 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E

Centre lock, vertical, with load transferSRH / mm CL1 CL2 CL3

1101 – 1150 550 – – C 400 E

1151 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E

Centre lock, horizontal, without turn-restrictorSRW / mm CLH1 CLH2

450 – 650 258 – CL 200 P

651 – 850 462 – CL 400 P

851 – 1000 658 – CL 600 P

Centre lock, horizontal, with turn-restrictorSRW / mm CLH1 CLH2

650 – 850 258 – CL 200 P

851 – 1050 462 – CL 400 P

1051 – 1250 658 – CL 600 P

1251 – 1400 658 858 CL 600 E CON + CL 200 P

G3



Installation drawingsPositioning of the frame componentsilt urn – RC1 N


310 – 450 – – – – – – –

451 – 620 – – – – – – –

621 – 800 125 – – – – 137 –

801 – 1200 125 – – – – 137 –

1201 – 1600 125 340 – – – 137 –

1601 – 2000 – 312 358 – – 109 232

2001 – 2400 – 312 358 758 740 109 232

2401 – 2600 – 318 358 758 740 109 232

58

86.576

BE

AC

D

Tilt striker

BC

LMD

1)LMD

2)

Handle/centre


Installation drawingsPositioning of the frame componentsilt urn – RC2 RC2 N



58

86.5

149

76

12

95

CLH1

Tilt striker

BC

LMD

G4

G3

G2

HH

CL2

CL1

CLH2

G1

CL4

CL3

A

Turn-restrictor

T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 G4 LMD C

490 – 600 170 – – – – 223 –

601 – 800 263 – 383 – – 138 –

801 – 1000 413 160 550 – – 288 –

1001 – 1200 513 160 700 – – 388 –

1201 – 1400 563 160 700 – – 388 –

1401 – 1600 563 160 700 1170 – 388 –

1601 – 1800 563 160 700 1370 – 388 –

1601 – 1800 1000 160 700 1370 – 1121 1244

1801 – 2000 1000 160 700 1370 – 1121 1244

2001 – 2200 1000 160 700 1370 1770 1121 1244

2201 – 2400 1000 160 700 1370 1770 1121 1244


801 – 1000 600 500 / 890

1001 – 1200 600 500 / 1090

1201 – 1400 600 500 / 1090

Centre lock, horizontal, without turn-restrictorSRW / mm CLH1 CLH2

450 – 650 258 – C 200

651 – 850 462 – C 400

851 – 1000 658 – C 600


650 – 850 258 – C 200

851 – 1050 462 – C 400

1051 – 1250 658 – C 600

1251 – 1400 658 858 C 600 CON C 200

Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3 CL4

490 – 650 346 – – – C 200

651 – 850 550 – – – C 400

851 – 1050 746 – – – C 600

1051 – 1250 746 946 – – C 600 CON C 200

1251 – 1450 746 1150 – – C 600 CON C 400

1451 – 1650 746 1346 – – C 600 CON C 600

1651 – 1850 746 1346 1546 – 2x C 600 CON C 200

1851 – 2050 746 1346 1750 – 2x C 600 CON C 400

2050 – 2250 746 1346 1946 – 2x C 600 CON C 600

2251 – 2400 746 1346 1946 2146 3x C 600 CON C 200


1000 – 1150 550 – – C 400

1151 – 1350 746 – – C 600

1351 – 1550 746 946 – C 600 CON C 200

1551 – 1750 746 1150 – C 600 CON C 400

1751 – 1950 746 1346 – C 600 CON C 600

1951 – 2150 746 1346 1546 2x C 600 CON C 200

2151 – 2350 746 1346 1750 2x C 600 CON C 400

2351 – 2400 746 1346 1946 2x C 600 CON C 600


58

BE

AC

D

76

Tilt striker

BC

LMD

1LMD

2

Handle/centre


Installation drawingsPositioning of the frame componentsilt urn – RC2 RC2 N

SRH / mm A B C D E LMD 1 LMD 2 C

490 – 620 – – – – – – – –

621 – 800 125 – – – – 137 – –

801 – 1200 125 – – – – 137 – –

1201 – 1600 125 340 – – – 137 – –

1601 – 2000 – 312 358 – – – 109 232

2001 – 2400 – 312 358 758 740 – 109 232



Installation drawingsPositioning of the frame componentsTurn-Only hardware – Basic security


76 50

58

50

50

12

95CLH1

Cen

tre-

clos

ers,

con

ceal

ed

BC

LMD

G4

G3

G2

CL2

CL1

CLH1

Turn-restrictor

HH

CL3

T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 G4 LMD C

280 – 480 120 – – – – – –

481 – 600 170 – – – – 223 –

601 – 800 263 – – – – 138 –

801 – 1000 413 – – – – 288 –

1001 – 1200 513 – 700 – – 388 –

1201 – 1400 563 – 700 – – 388 –

1401 – 1600 563 – 700 – – 388 –

1601 – 1800 563 – 700 1370 – 388 –

1601 – 1800 1000 – 700 1370 – 1121 1244

1801 – 2000 1000 – 700 1370 – 1121 1244

2001 – 2200 1000 – 700 1370 – 1121 1244

2201 – 2400 1000 – 700 1370 – 1121 1244

2401 – 2600 1000 – 700 1370 1770 1121 1244

Centre-closer, concealedSRH / mm CL1 CL2 CL3

1000 – 1200 550 – –

1201 – 1800 746 – –

1801 – 2400 746 1346 –

2401 – 2600 746 1346 1946

Centre lock, horizontal, topSRW / mm CLH1 Top

1101 – 1400 676 600 E

Centre lock, horizontal, bottomSRW / mm CLH1 Bottom

1101 – 1400 658 600 E


Installation drawingsPositioning of the frame componentsTurn-Only hardware – Basic security

Basic security


76 50

58

BC

LMD

LMD

Handle/ centre

BC

AB

E


310 – 450 – – – – – – –

451 – 620 – – – – – –

621 – 800 125 – – – – 137 –

801 – 1200 125 – – – – 137 –

1201 – 1600 125 340 – – – 137 –

1601 – 2000 – 312 358 – – 109 232

2001 – 2400 – 312 358 758 740 109 232

2401 – 2600 – 312 358 758 740 109 232


5876

7658

Installation drawingsPositioning of the frame componentsTilt-Only hardware – Basic security

Basic security

CL1

CL1

Centre-closer, concealed

BA

SRW / mm A B

451 – 620 – –

621 – 800 125 –

801 – 1200 125 –

1201 – 1400 125 340

Centre lock, verticalSRH / mm CL1 Right

801 – 1200 480 – – 400 E

Centre lock, verticalSRH / mm CL1 Left

801 – 1200 462 – – 400 E


Installation drawingsPositioning of the frame componentsurn Only ilt urn – asic security

w/o centre post


12

70

52

A

52

149

52CLH1

Centre of clearance

CL2

CL1

CLH1

12 mm clearance between the sashes

CLH1

CL2

CL1

Cen

tre-

clos

ers,

con

ceal

ed

Tilt striker

CL3

CL3

Centre-closer, concealedSRH / mm CL1 CL2 CL3

1000 – 1200 550 – –

1201 – 1800 746 – –

1801 – 2400 746 1346 –

2401 – 2600 746 1346 1946

Centre lock, horizontal, topSRW / mm CLH1 Top

1100 – 1400 652 CL 600 E

Centre lock, horizontal, bottomSRW / mm CLH1 Bottom

1100 – 1400 652 CL 600 E


1101 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E


1101 – 1150 550 – – C 400 E

1151 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E

Centre lock, horizontalSRW / mm CLH1

1101 – 1400 652 CL 600 E


801 – 1000 600 500 / 890

1001 – 1200 750 500 / 1090

1201 – 1400 750 500 / 1090




Installation drawingsPositioning of the frame componentsurn Only ilt urn – RC1 N



1101 – 1800 728 – – C 600 E

2001 – 2400 728 1328 – CL 600 E CON + CL 600 E

2401 – 2600 728 1328 1732 2x CL 600 E CON + CL 400 E


1101 – 1150 532 – – C 400 E

1151 – 1800 728 – – C 600 E

1801 – 2400 728 1328 – CL 600 E CON + CL 600 E

2401 – 2600 728 1328 1732 2x CL 600 E CON + CL 400 E

Centre lock, horizontal, without turn-restrictor, bottomSRW / mm CLH1

450 – 650 252 CL 200 P

651 – 850 456 CL 400 P

851 – 1000 652 CL 600 P

Centre lock, horizontal, with turn-restrictor, bottomSRW / mm CLH1 CLH2

650 – 850 252 – CL 200 P

851 – 1050 456 – CL 400 P

1051 – 1250 652 – CL 600 P

1251 – 1400 652 852 CL 600 E CON + CL 200 P

Centre lock, horizontal, topSRW / mm CLH1 CLH2

911 – 1110 452 – CL 400 E CON

1111 – 1310 652 – CL 600 E CON

1311 – 1400 652 – C 600 E CON C 200 CON

Centre lock, vertical, without load transfer SRH / mm CL1 CL2 CL3

1101 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x CL 600 E CON + CL 400 E


1101 – 1150 550 – – C 400 E

1151 – 1800 746 – – C 600 E

1801 – 2400 746 1346 – CL 600 E CON + CL 600 E

2401 – 2600 746 1346 1750 2x CL 600 E CON + CL 400 E

Centre lock, horizontal, without turn-restrictorSRW / mm CLH1

450 – 650 252 CL 200 P

651 – 850 456 CL 400 P

851 – 1000 652 CL 600 P


650 – 850 252 – CL 200 P

851 – 1050 456 – CL 400 P

1051 – 1250 652 – CL 600 P

1251 – 1400 652 852 CL 600 E CON + CL 200 P


801 – 1000 600 500 / 890

1001 – 1200 750 500 / 1090

1201 – 1400 750 500 / 1090

w/o centre post

52

52 70

52

12

149

131

9595

CLH1

Centre of clearance

CL2

C1

CLH1


CLH1

CL2

CL1

Tilt striker

CL3

CL3

CLH2 CLH2

A

Turn-restrictorTurn-restrictor




Installation drawingsPositioning of the frame componentsurn Only ilt urn – RC2 RC2 N



490 – 650 328 – – – C 200

651 – 850 532 – – – C 400

851 – 1050 728 – – – C 600

1051 – 1250 728 928 – – C 600 CON C 200

1251 – 1450 728 1132 – – C 600 CON C 400

1451 – 1650 728 1328 – – C 600 CON C 600

1651 – 1850 728 1328 1528 – 2x C 600 CON C 200

1851 – 2050 728 1328 1732 – 2x C 600 CON C 400

2051 – 2250 728 1328 1928 – 2x C 600 CON C 600

2251 – 2400 728 1328 1928 2128 3x C 600 CON C 200


1000 – 1150 532 – – C 400

1151 – 1350 728 – – C 600

1351 – 1550 728 928 – C 600 CON C 200

1551 – 1750 728 1132 – C 600 CON C 400

1751 – 1950 728 1328 – C 600 CON C 600

1951 – 2150 728 1328 1528 2x C 600 CON C 200

2151 – 2350 728 1328 1732 2x C 600 CON C 400

2351 – 2400 728 1328 1928 2x C 600 CON C 600


450 – 650 252 C 200

651 – 850 456 C 400

851 – 1000 652 C 600


650 – 850 252 – C 200

851 – 1050 456 – C 400

1051 – 1250 652 – C 600

1251 – 1400 652 852 C 600 CON C 200

Centre lock, horizontal, topSRW / mm CLH1 CLH2

711 – 910 252 – CL 200 CON

911 – 1110 452 – C 400 CON

1111 – 1310 652 – C 600 CON

1311 – 1400 652 852 C 600 CON C 200 CON


490 – 650 346 – – – C 200

651 – 850 550 – – – C 400

851 – 1050 746 – – – C 600

1051 – 1250 746 946 – – C 600 CON C 200

1251 – 1450 746 1150 – – C 600 CON C 400

1451 – 1650 746 1346 – – C 600 CON C 600

1651 – 1850 746 1346 1546 – 2x C 600 CON C 200

1851 – 2050 746 1346 1750 – 2x C 600 CON C 400

2051 – 2250 746 1346 1946 – 2x C 600 CON C 600

2251 – 2400 746 1346 1946 2146 3x C 600 CON C 200


1000 – 1150 550 – – C 400

1151 – 1350 746 – – C 600

1351 – 1550 746 946 – C 600 CON C 200

1551 – 1750 746 1150 – C 600 CON C 400

1751 – 1950 746 1346 – C 600 CON C 600

1951 – 2150 746 1346 1546 2x C 600 CON C 200

2151 – 2350 746 1346 1750 2x C 600 CON C 400

2351 – 2400 746 1346 1946 2x C 600 CON C 600


450 – 650 252 C 200

651 – 850 456 C 400

851 – 1000 652 C 600


650 – 850 252 – C 200

851 – 1050 456 – C 400

1051 – 1250 652 – C 600

1251 – 1400 652 852 C 600 CON C 200


801 – 1000 600 500 / 890

1001 – 1200 600 500 / 1090

1201 – 1400 600 500 / 1090

52

52

149

131

12

7052

9595

CLH1CLH2

C2

C1


CLH1

CL2

CL1

Tilt striker

CL3 C

3

CL4

A

CL4

CLH1

CLH2CLH2

Turn-restrictorTurn-restrictor

w/o centre post


Top horizontal

Bottom horizontal

Esp

agno

lett

e si

de

Standard

RC1

Hin

ge

side

10

8

8

5

3 7 6

5

8

10

30

31

32

5 7 3 40

5 14

Installation drawings Jigs

espagnolette, fixed handle height ultipart centre lock, asic security RC1 N


Installation drawings Jigs

espagnolette, fixed handle height ultipart centre lock, asic security RC1 N

3 – 8 Single positioning jigs timber, T&T standardDescription Material no.

3

espagnolette side SRH 1601 – 2600 hinge side SRH 1801 – 2600

290050

5

bottom SRW 330 – 1100 hinge side SRH 280 – 1100 top hori ontal SRW 431 – 800

290072

6 Single positioning jig for lifting mishandling

espagnolette side SRH 481 – 800

290073

7 Single positioning jig espagnolette side SRH 801 – 1600 hinge side SRH 1101 – 1800

290074

8 Single positioning jig centre lock bottom hori ontal SRW 1101 – 1400 top hori ontal SRW 801 – 1400

290075

3 – 10 Single positioning jigs timber, TU-ON standardDescription Material no.

3


290050

5

bottom hinge side SRW SRH 315 – 1100 top hori ontal SRW 315 – 1200

290072



290073

7 Single positioning jig espagnolette side SRH 801 – 1600

290074

10

top bottom hori ontal 1101 – 1600290081

3 – 32 Single positioning jigs timber, T&T RC1Description Material no.

3


290050

5

top hori ontal SRW 450 – 800290072



290073

7 Single positioning jig espagnolette side SRH 801 – 1600 hinge side SRH 1101 – 1800

290074

8 Single positioning jig centre lock top hori ontal SRW 801 – 1400

290075

30 Positioning jig for centre lock bottom hori ontal SRW 450 – 800

SRW 1001 – 1050

268931


SRW 1051 – 1250

268932


268933

40 Positioning jig hinge side SRH 280 – 2600

640450

14 602577

602597


AdjustmentExplanation on the adjustment chapter

Symbols for the sash adjustment when installedThese symbols facilitate the orientation while adjusting the window sashes

after installation with the following steps. se a 4 mm hex key as tool.

Height adjustment

Lateral adjustment

Gasket-compression adjustment

NOTE!Adjusting Roto hardware components may only be carried out by

authorised and qualified personnel.

NOTE!The stated values in the adjustment instructions chapter are

maximum values. hese must be adhered to.


AdjustmentAdjustment instructionsSash stay

+2.0

–2.0

Lateral adjustment

+0.5

–0.5



+1.

5–

1.0

Height adjustment

After the height adjustment, the load transfer device has

to be read usted (refer to page 71).

+2.0

–1.5

Lateral adjustment

+0.5

–0.5


AdjustmentAdjustment instructions

ivot rest corner hinge


Adjustment Adjustment instructionsLocking cams

Locking cam adjustment instructions

Cam type Adjustment range Gasket-compression Height Side view Tools

E cam

90° 90°

–

P cam

90° 90°

–

V camCam type Adjustment range Gasket-compression

adjustment in mm Height adjustment in mm

Side view / top view Tools

90° 90°

– 0.8 mm – 0.2 mm

180° 180°

– – 0.4 mm

270° 270°

– 0.8 mm – 0.6 mm

360° 360°

– – 0.8 mm

0 = Original position

– 0.8 mm max. ad ustment

0.8 mm max. ad ustment


OperationOperating informationHandle positions of ilt urn hardware

The following symbols show the different handle positions and the resulting

sash positions of windows and balcony doors.

Handle position Sash position Symbol Meaning

Closed position of the sash.

Opened turn position of the sash.

Opened tilt position of the sash.

Malpositioning of the sash.


OperationOperation information for end-usersHandle positions of ilt urn ilt irst hardware

The following symbols and signs can be used on windows and balcony doors

to protect the end-user.

lease order stickers separately (O R 14 E EN, O R 15 E EN).

geschlossenclosed

Drehkipp-BeschlagTilt&Turn hardware

öffnenopen

kippentilt

FehlschaltungenvermeidenAvoid mishandling mode!

08/2012 OPR_14_DE-EN_v1

geschlossenclosed

TiltFirst-BeschlagTiltFirst hardware

kippentilt

öffnenopen

FehlschaltungenvermeidenAvoid mishandling mode!

08/2012 OPR_15_DE-EN_v1


Operation Troubleshooting

Troubleshooting

Problem Cause Corrective action Specialist company

End-users

Handle is difficult

to rotate.

– Frame parts are not properly

greased.

– Faulty handle.

– Handle screws are screwed in

too strong.

– Oblique screws in the sash

parts.

– Faulty sash parts.

– Incorrect strikers.

– Sash stay gasket compression

too strong (accumulation of

gaskets).

– Grease frame parts.

– Replace the handle.

– Slightly loosen the screws.

– Straight screw fixing of the

sash parts.

– Replace the sash parts.

– Replace strikers.

– Adjust or reduce the sash stay

gasket compression.

–

–

–

–

–

–

Handle can not ro-

tate 180°.

– Faulty hinging or installation

of sash parts.

– Faulty striker locations.

– Check adjustment in turn posi-

tion (if necessary, rehinge the

sash proceeding from

espagnolette).

– Adjust the striker locations.

–

–

In turn mode, the

sash falls into tilted

position.

– Too much clearance on top. – Check corner hinge location.

– Check pivot rest location.

– Raise the corner hinge.

( ttention tilt striker)

–

–

–

In tilt mode, the

sash falls into

turning position.

– Faulty tilting component. – Replace tilting component. –

Sash is rubbing in

tilt mode.

– Insufficient clearance on top. – Lower the corner hinge.

( ttention tilt striker )

–

Locking cams

rubber at striker.

– Faulty hinging of the sash.

– Faulty striker locations.

– Rehinge the sash.

– Adjust the striker locations.

–

–

= To be carried out only by a specialist company.

– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user


WARNING!Danger of injury through incorrectly conducted maintenance work!Incorrect maintenance can result in serious personal injury or material damage.– Before starting work, ensure that there is sufficient installation

room.

– Maintain order and cleanliness at the installation location.

– Ensure that the window or balcony door is prevented from

suddenly slamming during maintenance work.

– Get a specialist company to carry out adjustment work on hard-

ware – especially in the area of pivot rests or bogies and of

hinges – as well as replacement of parts and hinging, and

unhinging of sashes.

– Do not unhinge the sash for maintenance work.

At least annually, every six months for

Specialist company

End-users

If necessary, tighten fixing screws. –

Replace damaged screws. –

If necessary, replace components. –

Lubricate all moving components with acid free

and non resinous oil from a specialised dealer.

Lubricate steel strikers with acid free and non

resinous grease from a specialised dealer.



NOTE!Observe the following environmental protection notes during

– Remove emerging or residual grease at the lubricating points

and dispose of in accordance with the valid local regulations.

– Collect exchanged oil in suitable containers and dispose of in

accordance with the environmental regulations.

The hardware overview shows the arrangement of the lubrication points. The

illustrated overview does not necessarily correspond to the installed hardware.

The number of lubrication points depends on the size and design of the win-

dow.

Maintenance Maintenance


Maintenance Lubrication points

Grease

Oil


Inspection

t least annually, every six months for school and hotel buildings

Specialist company

End-users

Check that safety-relevant hardware compo-

nents are mounted securely.

Examine safety relevant hardware components

for wear and tear.

All movable parts are to be operation-tested.

All locking points are to be operation-tested.

The hardware’s smooth operation can be

checked by means of moving the window

handle:

– In accordance with IN 18055, the locking

and unlocking moment is max. 10 Nm.

– It can be checked using a torque wrench.

– The smooth operation can be improved by

greasing/oiling or adjusting the hardware.

–

–

– = To be carried out only by a specialist company.


Care

Specialist company

End-users

Keep the hardware free from deposits and

soiling.

Never use aggressive, acidic cleaners or

abrasive cleaning agents.

Only use mild, pH-neutral cleaning agents

in diluted form.

Only use a soft cloth for cleaning.


– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user.

No legal claims can be derived from these recommendations, the application

is to be conveyed for each concrete individual case. The window and balcony

door manufacturer must draw builders and end-user’s particular attention to

these maintenance instructions. Roto Frank AG recommends window fabri-

cators to make maintenance agreements with their end-users.

Maintenance Inspection and care


Protection against corrosion

Specialist company

End-users

Aggressive vapours (e.g. by means of formic

acid or acetic acid, ammonia, amine or ammo-

nia compounds, aldehydes, phenols, chlorine,

tannic acid etc.) in the vicinity of the windows

must be absolutely avoided.

–

Never use acetic-acid or cross-linked acidic

sealing compounds or those with the above

mentioned contents, since both the direct con-

tact with the sealing compound and its vapori-

sation can attack the hardware’s surface.

–

Only electrogalvanised zinc plated and passi-

vated screws may be used for fixing the hard-

ware components.

–

o not use any stainless steel screws – = To be carried out only by a specialist company.


Protection against dirt

Specialist company

End-users

Remove deposits and dirt from building mate-

rials (building dust, plaster, cement, etc.) or

similar materials with water before it cures.

Keep the hardware free from deposits and

soiling.

Never use aggressive, acidiferous cleaners or

abrasive cleaning agents.

Only use mild, pH-neutral cleaning agents in

diluted form.

Only use a soft cloth for cleaning. = To be carried out only by a specialist company.


Maintenance Preservation of the surface finish


Specialist company

End-users

entilate the hardware and the rebate areas –

especially in the construction phase – so that

they are neither exposed to direct contact

with water nor to formation of condensation

water.

Ensure that (permanently) damp spatial air

cannot condense in the hinge and rebate

areas:

– Force ventilate several times each day

(open all windows for approx. 15 minutes).

– Also ventilate during holidays and ab-

sences.

– or more complex construction pro ects,

develop a ventilation plan if necessary.

If described systematic ventilation is not pos-

sible, e.g. because fresh screed must not be

traversed, or it cannot take draughts, put the

windows into the tilted position and make

them airtight by taping on the indoor side.

Divert the moisture present in the room air to

the outside by means of condensation dryers.



Protection against damages due to renovation work

Specialist company

End-users

When applying surface treatments of the win-

dows, exclude all hardware components from

this treatment, and thus protect against con-

tamination.

Use only adhesive tapes which do not dam-

age the varnish layers. In the case of doubt,

ask the window fabricator.


– = Not to be carried out by the end-user; the end-user may not carry out installation work!

= To be carried out either by a specialist company or by the end-user.

Maintenance Preservation of the surface finish


DismantlingUnhinging the sash with load transfer device

Unhinge the load transfer device.

1. Bring the handle into the turn mode, open the

sash 90° and release the load transfer device.2. Press down the lifting mishandling device (if

mounted) and bring the handle into the tilt position.3. Unhinge the sash stay and secure the sash from

falling out.4. Press down the lifting mishandling device and bring

the handle into the turn mode.5. Turn the sash closed.6. Lift the sash slightly tilted out of the pivot rest.

NOTE!Screw out the screw of the load transfer

device until the spring tension is released

completely (support rod is loosened).

If the tension in the spring is not completely

released, the sash cannot be hinged into the

frame again.


DismantlingUnhinging the sash without load transfer deviceSash stay 350, 500 and sash stay 250

Unhinging the sash

1. Bring the handle into the turn mode (= open sash

position).2. Press down the lifting mishandling device (if

mounted) and bring the handle into the tilt position.3. Unhinge the sash stay and secure the sash from

falling out.

4. Press down the lifting mishandling device and bring

the handle into the turn mode.5. Turn the sash closed.6. Lift the sash slightly tilted out of the pivot rest.


TransportTransport, packaging, storage

DANGER!Danger to life from incorrect handling and transport!Incorrect handling and unsuitable transport of window elements

can result in dangerous circumstances and cause severe accidents,

even including death.

Therefore:

– During loading and unloading, select force application points

which exclusively create reaction forces appropriate to the de-

signed layout of the hardware components for the intended in-

stallation location.

– During handling and transport, ensure that hardware is in the

locked position, so as to prevent an uncontrolled opening of the

sash. Use suitable means of securing for this.

– Use only transport protections designed for the respective clear-

ance.

– Wherever possible, transport the windows in the intended instal-

lation position. If transport in the intended installation position is

not possible, unhinge the sash, and transport it separately from

the frame to which it belongs.

uring transport, loading, and unloading, especially when auxiliaries such as

suckers, transport nets, forklifts, or cranes are used for support, reaction

forces may arise which result in damage or overloading to the installed hard-

ware. Therefore observe the following during all transport, loading, and un-

loading:

The type and the force application points when transporting, loading, and

unloading have a significant effect on the reaction forces which arise.

– Always choose the force application points so that the resulting reac-

tion forces are dissipated appropriate to the designed layout of the

hardware components for the intended installation location. This ap-

plies particularly for the hinge positions.


TransportTransport inspection

Check the delivery on receipt immediately for completeness and transport

damage.

NOTE!Claim any damage as soon as it is detected. Claims for damage can

only be invoked within the statutory reclamation period.


Disposal

Separate the hardware components from the window and dispose of as

metal scrap.

C

ated

: an

uar

y 2

01

7

Su

bec

t to

ch

ang

e

O

_10

9_

N_v

© 2

01

7 R

oto

Fra

nk

AG

®

Ro

to is

a r

egis

tere

d t

rad

emar

k

Roto Frank AGWindow and Door Technology

Wilhelm-Frank-Platz 1

70771 Leinfelden-Echterdingen

Germany

Phone +49 711 7598 0

ax 49 711 7598 253

[email protected]

www.roto-frank.com

Roto Tilt&Turn | he ilt urn hardware system for windows and balcony doors

Roto Sliding | Hardware systems for large sliding windows and doors

Roto Door | Matching hardware technology “everything about doors”

Roto Equipment | Additional technology for windows and doors

roto nt designo - roto north america · 8 february 2017 imo_109_de_v5_en roto nt designo subject to...

Documents