rs320 - schulte.ca code... · 2 100-3201h 1 cyl. 3x30 tie rod orb ports 3 111-121 2 hyd. hose...

®

RS320ROCK REMOVAL

Published: 01/18 Part No. 90-010P S/N: 9011973805-9012030903 inclusive

PARTS MANUALAn Operators Manual with IMPORTANT Safety, Assembly,Operation andMaintenance informationwas packagedwith thisParts Manual during final inspection at the factory. If theOperatorsManual ismissing at any time, please contact SchulteIndustries Ltd. At (306) 287-3715 to receive your freereplacement manual.

Si No Lee Ingles, PidaAyuda a Alguien

Que Se Lo Lea Para Que leTraduzca Las

Medidas de Seguridad

¡ATENCIÓN!LEA EL INSTRUCTIVO

Schulte Industries Ltd.PO Box 70Englefeld SaskatchewanCanada S0K 1N0Tel. (306) 287-3715Fax. (306) 287-3355Parts Fax. (306) 287-4066Email: [email protected]: www.schulte.ca © 2010 Alamo Group

mailto:[email protected]

http://www.schulte.ca

Parts Ordering GuideThe following instructions are offered to help eliminate delay and error in processing purchaseorders for the equipment in this section.

1. The Purchase Order must include the name and address of the person or organization orderingthe parts, who should be charged, and if possible, the serial number of the machine for whichthe parts were ordered.

2. The Purchase Order must clearly list the quantity of each part, the complete and correct partnumber, and the description of the part.

3. Schulte Industries Ltd reserves the right to substitute parts where applicable.

4. Schulte Industries Ltd reserves the right to change prices without prior notice.

NOTE: Please refer to the Safety Section in the front of the Operators Manual for the properPart Number when ordering Replacement Safety Decals. Safety decals are availablefree of charge from the Schulte Parts Department.

NOTE: If the Operators Manual does not accompany this Parts Manual please obtain one, freeof charge from the Schulte Parts Department. DO NOT operate this implement unlessyou READ, UNDERSTAND, and FOLLOW the Safety and Operation instructionscontained in the Operators Manual

NOTE: Please note that the appearance of some parts may vary from the artwork shown inthe Manual.

For maximum safety and to guarantee optimum product reliability, always usegenuine Schulte Parts. The use of inferior replacement parts may cause prematureor catastrophic failure, which could result in serious injury or death.Direct any questions regarding parts to:

Schulte Industries Ltd ®P.O. Box 70

Englefeld, SaskatchewanCanada S0K 1N0

Phone: (306)-287-3715Parts Fax: (306) 287-4066

Email: [email protected]

®

mailto:[email protected]

PART NAME INDEX

RS320 - MAIN FRAME - REV 2017-01....................................................................................................................................................... 4

RS320 - BUCKET & GRATE - REV 2019-08.............................................................................................................................................. 6

RS320 - ROCK DEFLECTOR KIT - REV 2015-03..................................................................................................................................... 8

RS320 - ROCK PICKER HEADER - REV 2010-04................................................................................................................................... 10

RS320 - HUB & AXLE - REV 2016-01...................................................................................................................................................... 12

RS320 - HYD CIRCUIT (MONARCH) - REV 2013-01............................................................................................................................ 14

RS320 - HYDRAULIC DRIVE - REV 2018-01......................................................................................................................................... 16

RS320 - HYDRAULIC CYLINDER, 100-4251 - REV 2006-05................................................................................................................ 18

RS320 - HYDRAULIC CYLINDER, 100-3191H, 100-3201H - REV 2013-01......................................................................................... 19

RS320 - MOTOR VALVE KIT (ELECTRICAL) - REV 2005-03............................................................................................................. 20

RS320 - CONVEYOR TYPE MOTOR VALVE KIT - REV 2010-04....................................................................................................... 21

RS320 - SWING HITCH - REV 2013-01.................................................................................................................................................... 22

RS320 - HYDRAULIC CYLINDER, 100-3120H - REV 2013-01............................................................................................................. 23

RS320 - LIGHT KIT ASSEMBLY, S000-075 - REV 2015-03................................................................................................................... 24

RS320 - LIGHT KIT, S000-088 - REV 2017-08......................................................................................................................................... 25

RS320 - SAFETY CHAIN S000-011 - REV 2007-01................................................................................................................................. 26

©2009 Alamo Group Inc. Parts Section -3

RS320 REV 2018-01

RS320 - MAIN FRAME - REV 2017-01

ITEM PART NO. QTY. DESCRIPTION1 270-020 3 LOCKNUT, 5/16 UNC, PLATED

2 124-010 8 HYDRAULIC LINE CLAMP, PLASTIC

3 256-020 2 WASHER, 5/16"

4 590-436 1 HYDRAULIC SHIELD, RS320

5 575-068 1 GRATE LUG, OFFSET

6 250-008 2 BOLT, 5/16 X 1-1/4 UNC, GR5, PLATED,

7 362-006 1 TENSION BUSHING, 1" X 1-3/8" X 1" LG.

8 232-575 1 SCREW JACK SIDE WIND 10"

9 256-017 8 WASHER, 3/8"

10 270-017 4 LOCKNUT, 3/8 UNC, PLATED


RS320 REV 2018-01

RS320 - MAIN FRAME - REV 2017-01

Continued...

ITEM PART NO. QTY. DESCRIPTION11 90-06 1 HYDRAULIC LINE SHIELD, RSH4 / RS320,

12 524-193 1 HYDRAULIC LINE SHIELD, RS320

13 250-090 2 BOLT, 5/8 X 2 UNC, GR5, PLATED

14 250-059 4 BOLT, 1/2" X 1-1/2"

15 228-012 2 HOSE ORGANIZER, 20-5/8" O/L, 5/8" MOUNTING HOLE

16 C000-001 4 HOSE AND TUBE CLAMP, 1/2"

17 256-006 2 WASHER, 5/8"

18 90-08 2 GRATE PIN, (RETAINING STYLE)


20 250-057 3 BOLT, 1/2 X 2 UNC, GR5

21 271-051 3 COTTER, HAIR PIN, 3/16

22 250-089 2 BOLT, 5/8 X 2-1/4 UNC, GR 5, PLATED

23 R000-115 1 HITCH POLE SWING ASSEMBLY

24 R000-112 2 CLEVIS HALF

25 250-106 2 BOLT, 3/4" X 6-1/2"


27 250-093 2 BOLT, 5/8" X 1-3/4" UNC, GR5, PLATED

28 60-53 2 LOCK-UP PIN

29 90-05 1 ROCK DEFLECTOR ASSEMBLY

30 90-01 1 FRAME ASSEMBLY, RS320


33 250-114 9 BOLT, 3/4" X 2-1/2" UNC, GR5, PLATED,

34 273-006 2 GREASE NIPPLE, SELF-TAP, 1/4-28

35 90-42 2 PIVOT HINGE ASSEMBLY

36 R200-116 1 WEDGE LOCK ASSEMBLY,

37 R100-116 1 HITCH POLE PIVOT PIN,

38 90-41 2 PIVOT HINGE COVER

39 250-049 1 BOLT, 1/2 X 4 UNC, GR8, PLATED,

40 256-011 3 WASHER, 1/2"

41 273-001 2 GREASE NIPPLE, 1/8 NPT, STRAIGHT,

42 257-071 5 LOCKING FLANGE NUT, 1/2"

43 C000-355 1 MANUAL CANISTER MOUNT BRACKET

44 280-201 1 PLASTIC MANUAL STORAGE CANNISTER

45 250-002 3 BOLT, 1/4" X 1" UNC, GR5, PLATED

46 256-018 3 WASHER, 1/4"


48 590-1262 1 GRATE SIDE GUARD

49 R800-208 - SPACER, 1/4" (USE AS REQUIRED)

50 R800-209 - SPACER, 10GA. (USE AS REQUIRED)


RS320 REV 2018-01

RS320 - BUCKET & GRATE - REV 2019-08


RS320 REV 2018-01

RS320 - BUCKET & GRATE - REV 2019-08

Continued...

ITEM PART NO. QTY. DESCRIPTION1 90-02 1 BUCKET

2 250-0511 4 BOLT, 1/2" X 3", GRADE 8

3 250-0221 4 PLOW BOLT, 3/8" X 3"

4 90-84 2 WEAR PLATE, FRONT IDLER

5 233-060 2 RUBBER BUMPER

6 90-101 1 GRATE, SOLID TIPS, 1-1/4" SPACING

7 90-86 1 CYLINDER LUG, GRATE END

8 271-005 3 COTTER PIN, 3/16" X 1-1/2"

9 302-014 1 CLEVIS PIN, 1" X 2-3/8" (USABLE LENGTH)

10 586-229 2 STABILIZER LINK ARM, LONG

11 256-001 2 FLAT WASHER, 1"


13 90-89 2 STOPPER PLATE, RS320 JUMBO

14 362-017 2 BUSHING, 1-7/8" O.D. X 1-5/8" I.D.

16 270-007 4 LOCKNUT, 1/2" UNC

17 605-014 4 WEAR PLATE, REAR

18 570-023 13 TIP, 2" THICK

19 94-06 12 T-IRON 1-1/4" SPACE

20 94-08 1 T-IRON, CENTER 1-1/4" SPACE

21 233-007 2 RUBBER PAD, REAR

22 250-052 4 BOLT, 1/2" X 2-1/2", UNC

23 362-010 1 TENSION BUSHING, 1" X 1-1/4" X 3/4" LG

24 270-034 4 CENTER LOCK NUT, 3/8"


RS320 REV 2018-01

RS320 - ROCK DEFLECTOR KIT - REV 2015-03


RS320 REV 2018-01

RS320 - ROCK DEFLECTOR KIT - REV 2015-03

Continued...

ITEM PART NO. QTY. DESCRIPTION1 73-03 1 FLAP HANGER, FIXED DEFLECTOR

2 73-04 1 UPRIGHT, RIGHT, 30" RUBBER

3 73-05 1 UPRIGHT, LEFT, 30" RUBBER

4 233-005 1 RUBBER FLAP 30" X 60" PVC

5 520-145 2 FLAP RETAINER BAR

6 590-447 1 BOTTOM ANGLE IRON

7 250-059 12 BOLT, 1/2" X 1-1/2" UNC GR5 PLATED

8 250-095 4 BOLT, 5/8" X 1-1/2" UNC GR5 PLATED

9 250-115 4 BOLT, 3/4" X 2" UNC GR5 PLATED

10 270-001 4 LOCKNUT, 3/4" UNC PLATED

11 270-004 4 LOCKNUT, 5/8" UNC PLATED

12 257-071 12 NYLOCK FLANGE NUT 1/2"


RS320 REV 2018-01

RS320 - ROCK PICKER HEADER - REV 2010-04

ITEM PART NO. QTY. DESCRIPTION3 312-143 2 IDLER SPROCKET

4 90-83 2 IDLER PIN

5 256-011 22 FLAT WASHER, 1/2"

6 250-061 1 BOLT, 1/2 X 1-1/4 UNC

7 255-009 3 LOCK WASHER, 1/2"

8 43-51 2 SLIDER

9 43-77 1 ROLLER CHAIN SET, 2-8 LINK, 6-7 LINK

10 43-60 4 ADJUSTER BOLT


RS320 REV 2018-01

RS320 - ROCK PICKER HEADER - REV 2010-04

Continued...

ITEM PART NO. QTY. DESCRIPTION11 257-008 4 NUT, 1" UNC

12 43-65 4 BATT, 3 X 4 X .250 TUBE

13 271-008 20 COTTER PIN, 1/8 X 1

14 311-142 8 DOUBLE CONNECTOR LINK, #140

15 262-005 2 ROLL PIN, 3/8 X 2-1/2

16 311-144 24 LINK PLATE #140

17 781-009 2 CONVEYOR BUSHING EXTENDED

18 256-054 10 MACH BUSH 1-5/8 X 3-3/8 X 10 GA

19 273-001 2 GREASE NIPPLE, 1/8- 27 NPT

20 251-021 8 BOLT, 18 MM X 65MM, CLASS 8.8 PLATED

21 270-030 8 LOCKNUT, 18MM PLATED

22 90-10 1 CONVEYOR FRAME HEAVY BEARINGS

23 43-49 1 DRIVE SHAFT

24 356-121 2 BEARING INSERT, 2" ROUND RACE

25 352-102 2 FLANGE BEARING COMPLETE

353-102 2 FLANGE HOUSING, 2" DUCTILE IRON

26 579-087 56 TOOTH

27 43-71 1 CONVEYOR ROLLER

28 742-004 2 CONVEYOR SHAFT

29 255-001 4 LOCK WASHER, 1"

30 250-063 2 BOLT, 1/2 X 1 UNC

31 619-005 1 WASHER 17/32 X 2-1/2 X 3/8 LONG

34 874-003 1 CONVEYOR DRIVE SHAFT SPACER BUSHING

35 256-073 4 MACH BUSH 2 X 3 X 14 GA

36 311-141 2 CONNECTOR LINK, #140

37 273-006 2 GREASE NIPPLE, SELF TAP, 1/4-28

38 90-87 2 IDLER CUSHION ROLLER

39 262-004 2 ROLL PIN, 3/8" X 3"

40 90-81 16 SPACER PLATE, 16 GA

41 256-511 4 HARDENED WASHER, 3 X 2 X .125

42 363-013 2 BRONZE BUSHING

43 A105-132 2 WASHER, PLATED

44 270-002 2 LOCKNUT, 1" UNC

45 250-019 4 BOLT, 3/8" X 1-1/4" UNC

46 256-017 2 WASHER, 3/8"

47 270-017 2 LOCKNUT, 3/8" UNC

48 255-013 2 LOCKWASHER, 3/8"

49 256-0533 2 MACHINE BUSHING, 2 X 3 X 10 GA.


RS320 REV 2018-01

RS320 - HUB & AXLE - REV 2016-01


RS320 REV 2018-01

RS320 - HUB & AXLE - REV 2016-01

Continued...

ITEM PART NO. QTY. DESCRIPTION1 R100-140 2 AXLE PLATE ASSEMBLY

2 207-005 2 SEAL (OR)

207-088 - SEAL, ADR

3 207-001 2 BEARING, INNER

4 207-002 2 RACE, INNER

5 273-006 2 GREASE ZERK, 1/4" (OR)

273-015 - GREASE ZERK, M8 X 1.25, ADR

6 205-001 2 HUB C/W OUTER RACES

7 207-004 2 RACE, OUTER

8 207-003 2 BEARING, OUTER

9 207-006 2 DUST CAP

10 206-011 2 HUB, C/W ITEMS #2-9

11 211-002 2 VALVE

12 201-006 2 WHEEL, SW14C X 16.1, 8 BOLT

13 207-060 16 WHEEL NUT (OR)

207-060ADR - WHEEL NUT SPECIAL

14 271-005 2 COTTER PIN, 3/16" X 1-1/2"

15 209-011 2 CASTLE NUT, 1"-14 UNF

16 209-010 2 WASHER

17 210-535 2 TIRE ASSEMBLY, 16.5L X 16.1 R3 10 PLY

210-535T - TIRE ONLY

18 207-047 16 WHEEL STUD (OR)

207-047ADR - WHEEL STUD SPECIAL

19 590-1054 2 WHEEL GUARD

20 250-089 4 BOLT, 5/8" X 2-1/4" UNC

21 270-004 8 LOCK NUT, 5/8" UNC

22 250-090 4 BOLT, 5/8" X 2" UNC

90-15 1 WHEEL GUARD KIT (INCL. REF. 19)


RS320 REV 2018-01

RS320 - HYD CIRCUIT (MONARCH) - REV 2013-01


RS320 REV 2018-01

RS320 - HYD CIRCUIT (MONARCH) - REV 2013-01

Continued...

ITEM PART NO. QTY. DESCRIPTION1 108-043 5 ELBOW, 90, 3/4-16 ORB MALE X 3/4-16 JIC MALE

2 100-3201H 1 CYL. 3X30 TIE ROD ORB PORTS

3 111-121 2 HYD. HOSE 3/8" X 68", 8MJIC X 8FJIC

4 108-030 2 RUN TEE, SWIVEL, 3/4-16 JIC MALE X 3/4 JIC FEMALE

5 108-031 2 ELBOW, 90DEG, #8 JIC MALE X #8 JIC FEMALE SWIVEL

6 108-005 2 MALE TEE, 3/4-16 JIC 37 DEG,

7 111-351 2 HYD HOSE 3/8"X185", 8FJICX8MORB, ORB PIONEER

8 111-146 1 HYD. HOSE 3/8" X 43", 8FJIC 90 X 8M-ORB

9 111-228 1 HYD. HOSE 3/8" X 45", 8FJIC X 8FJIC

10 100-4251 1 CYLINDER, 4 X 4 ,WELDED, MONARCH, ORB PORTS

11 302-014 1 CLEVIS PIN, 1 X 2-29/64

12 126-113 2 TUBE ASSEMBLY AS PER DRAWING

13 111-120 2 HYD. HOSE 3/8" X 37", 8MJIC X 8FJIC

14 126-112 2 TUBE ASSEMBLY AS PER DRAWING

15 100-3191H 1 CYL. 3X30 TIE ROD ORB PORTS

16 280-008 2 CABLE TIE, 15" LONG, UV BLACK, 120 LB. TENSILE

17 271-005 6 COTTER PIN, 3/16 X 1-1/2,

18 302-015 4 CLEVIS PIN, 1 X 2-7/8" USEABLE, ZINC DI-CHROMATE

19 90-79 1 GRATE CYLINDER PIN,MONARCH

20 256-001 4 WASHER, 1", 1-1/16" ID X 2" OD SAE


RS320 REV 2018-01

RS320 - HYDRAULIC DRIVE - REV 2018-01


RS320 REV 2018-01

RS320 - HYDRAULIC DRIVE - REV 2018-01

Continued...

ITEM PART NO. QTY. DESCRIPTION1 255-009 2 LOCKWASHER, 1/2

2 312-820 1 SPROCKET, 80B13, 1-1/4" BORE X 5/16` K/W, 2" LTB

3 257-032 2 NUT, 3/8", UNC,

4 268-004 1 SET SCREW, 3/8 X 1 UNC, ALLEN HEAD, CUP POINT,

5 268-006 1 SET SCREW, 1/2 X 1 UNC, SQUARE HEAD, CUP POINT,

6 257-022 2 NUT, 1/2 ", UNC,

7 46-01 1 DRIVE SHIELD, HYDRAULIC


9 256-053 2 MACHINE BUSHING, 2 X 3 X 10 GA.

10 116-017 1 HYDRAULIC MOTOR

117-972 - MOTOR SEAL KIT FOR 116-017

117-995 - RELIEF CARTRIDGE FOR 116-017

11 111-353 2 HYD HOSE 1/2" X 174", 8 MORB X 10 MORB, ORB PIONEER END

12 250-128 1 BOLT, 1 X 2 UNC, GR5, PLATED

13 255-001 2 LOCKWASHER, 1",

14 581-459 1 MOUNTING PLATE, HYDRAULIC MOTOR,


16 46-02 1 TIGHTNER, HYDRAULIC DRIVE

17 257-006 2 JAM NUT, 1" UNC, PLATED

18 310-802 1 ROLLER CHAIN, ANSI #80-1R, 41" LONG.

19 311-802 2 OFFSET LINK, ANSI #80-1, SINGLE

20 311-801 1 CONNECTOR LINK, ANSI #80-1, SINGLE

21 250-018 1 BOLT, 3/8 X 1 UNC, GR5,

22 255-013 1 LOCKWASHER, 3/8",

23 256-014 1 MACHINE BUSHING, 7/16 ID X 1-1/2 OD X 16 GA, PLATE

24 260-001 1 GIB HEAD KEY, 1/2 X 1/2 X 3, TAPERED,

25 268-013 1 SET SCREW, 3/8 X 1-1/4 UNC, ALLEN HEAD, CUP OINT,

26 250-090 1 BOLT, 5/8 X 2 UNC, GR5, PLATED

27 256-006 1 WASHER, 5/8",


30 312-802 1 SPROCKET, 80B35, 2" BORE X 1/2" K/W, 4-1/2" LTB


32 256-011 1 WASHER, 1/2, AS TYPE A, 9/16 IDX1-3/8 ODX.109,

33 117-912 1 KEY

34 250-057 2 BOLT, 1/2 X 2 UNC, GR5,

35 586-631 1 SHAFT CAP WITH KEY SLOT,

36 268-009 1 SET SCREW,1/2 X 1-1/4 UNC,SQUARE HEAD, CUP POINT

37 250-061 1 BOLT, 1/2 X 1-1/4 UNC, GR5,

38 256-001 1 WASHER, 1", 1-1/16" ID X 2" OD SAE


RS320 REV 2018-01

RS320 - HYDRAULIC CYLINDER, 100-4251 - REV 2006-05

ITEM PART NO. QTY. DESCRIPTION1 101-270 1 TUBE WELDMENT

2 101-272 1 PISTON

3 101-271 1 CYLINDER HEAD

4 101-273 1 ROD AND CLEVIS

5 101-274 1 SEAL KIT (COMPLETE)

6 101-243 1 PISTON NUT

7 101-297 4 TENSION BUSHING 1" X 1-1/4" X 5/8" LONG

100-4251 - COMPLETE CYLINDER, 4 X 4 MONARCH


RS320 REV 2018-01

RS320 - HYDRAULIC CYLINDER, 100-3191H, 100-3201H - REV 2013-01

ITEM PART NO. QTY. DESCRIPTION1 101-214 1 CLEVIS CAP, TC

2 101-330 1 SEAL KIT

3 101-012 1 CYLINDER TUBE, 3 X 30

4 257-022 8 NUT, 1/2" UNC

5 101-206 1 ROD CLEVIS

6 101-328 1 ROD CAP 3" TH

7 101-327 1 PISTON

8 250-023 1 CLEVIS BOLT, 3/8 X 1-3/4 UNC

9 257-032 1 NUT, 3/8" UNC

10 101-208 1 ROD 3 X 30

11 101-016 4 TIE ROD, 3 X 30

12 101-023 1 PISTON NUT

13 362-010 2 TENSION BUSHING, 1" I.D. X 1-1/4" X 3/4"

101-3191H - 3 X 30 CYLINDER, RIGHT SIDE

100-3201H - 3 X 30 CYLINDER, LEFT SIDE


RS320 REV 2018-01

RS320 - MOTOR VALVE KIT (ELECTRICAL) - REV 2005-03

ITEM PART NO. QTY. DESCRIPTION1 276-317 1 MODIFIED ENCLOSURE BOX

2 276-108 1 SWITCH

3 275-010 1 FUSE 5 AMP

4 277-004 1 WIRING HARNESS, SOLENOID, 12`

5 277-003 1 WIRING HARNESS, SWITCH, 4`

6 276-297 1 JUMPER CABLE

7 276-318 1 POWER HARNESS

8 276-320 1 COMPLETE SWITCH ASSEMBLY (REF 1-3, 5-7)

- - NOTE: 276-320 USES A 5 AMP FUSE.


RS320 REV 2018-01

RS320 - CONVEYOR TYPE MOTOR VALVE KIT - REV 2010-04

ITEM PART NO. QTY. DESCRIPTION1 111-352 1 HYD HOSE 3/8"X142", 8FJIC90SX8MORB, ORB PIONEER

2 250-018 4 BOLT, 3/8 X 1 UNC, GR5,


4 111-141 1 HYD. HOSE 1/2" X 54", 10M-ORB X 8FJIC 90

5 520-447 1 SHIELD, SOLENOID VALVE, RS

6 108-040 2 BRANCH TEE, ADJUSTABLE, 3/4-16 JIC X ORB,

7 127-100 1 SOLENOID OPERATED VALVE, #8 ORB," DOUBLE"

8 431-01 1 MOUNTING PLATE, SOLENOID VALVE, RS, RS320,

9 108-025 2 ADAPTER, #8 MALE ORB TO #8 MALE JIC

10 250-028 3 BOLT, 3/8 X 3-1/2, UNC, GR5, PLATED,

11 111-142 2 HYD. HOSE 3/8" X 33", 8FJIC X 8FJIC

12 111-353 1 HYDRAULIC HOSE (COMES WITH BASE UNIT, SEE PAGE 18)

13 111-351 2 HYDRAULIC HOSE (COMES WITH BASE UNIT, SEE PAGE 14)


RS320 REV 2018-01

RS320 - SWING HITCH - REV 2013-01

ITEM PART NO. QTY. DESCRIPTION1 100-3120H 1 CYL 3X8 3/4-16 ORB PORTS@90

2 302-015 2 CLEVIS PIN, 1 X 2-7/8" USEABLE, ZINC DI-CHROMATE

3 256-001 2 WASHER, 1", 1-1/16" ID X 2" OD SAE

4 271-005 2 COTTER PIN, 3/16 X 1-1/2,

5 362-015 1 TENSION BUSHING, 1" X 1-1/4" X 1" LG.

6 108-043 2 ELBOW, 90, 3/4-16 ORB MALE X 3/4-16 JIC MALE

7 C000-006 1 RESTRICTOR, SCREW IN, MALE ORB, 1/16" HOLE

8 111-343 2 HYD HOSE 3/8"X178", 8FJICX8MJIC, ORB PIONEER


RS320 REV 2018-01

RS320 - HYDRAULIC CYLINDER, 100-3120H - REV 2013-01

ITEM PART NO. QTY. DESCRIPTION1 101-201 1 CLEVIS CAP

2 101-331 1 SEAL KIT

3 101-220 1 CYLINDER TUBE

4 257-022 8 NUT

5 101-202 1 ROD CLEVIS

6 101-329 1 ROD CAP 3" TH

7 101-327 1 PISTON

8 250-023 1 CLEVIS BOLT

9 257-032 1 NUT

10 101-090 1 ROD, 3/8 X 8

11 101-221 4 TIE ROD, 3/8 X 8

12 101-023 1 PISTON NUT

100-3120H - COMPLETE CYLINDER


RS320 REV 2018-01

RS320 - LIGHT KIT ASSEMBLY, S000-075 - REV 2015-03

ITEM PART NO. QTY. DESCRIPTION1 S000-038 1 RS320 LIGHT BRACKET RIGHT (NOT USED WITH ROCK DEFLECTOR KIT)

2 S000-037 1 RS320 LIGHT BRACKET LEFT (NOT USED WITH ROCK DEFLECTOR KIT)

3 250-018 8 BOLT, 3/8" X 1" UNC GR5

4 256-017 4 WASHER, 3/8"


6 S000-088 1 SAFETY LIGHT KIT, INCLUDES WIRING HARNESS AND LIGHTS

7 S000-101 2 LIGHT GUARD BRACKET

8 280-008 10 CABLE TIE 15" 120 LB. TENSILE

9 270-028 2 LOCKNUT, 10-24 NYLOCK

10 251-151 2 10-24 X 3/4 PHILLIPS MACHINESCREW

11 254-004 8 RUBBER INSUL. CLAMP, 3/8"

12 251-154 8 SCREW, SELF DRILL, 1/4-14 X 3/4


RS320 REV 2018-01

RS320 - LIGHT KIT, S000-088 - REV 2017-08

ITEM PART NO. QTY. DESCRIPTION1 275-133 1 MAIN HARNESS, 25`

2 275-121L 1 LIGHT MODULE

3 275-138 1 CABLE, 12"

4 275-140 1 CABLE, 132"

5 275-111L 2 LIGHT, AMBER

6 275-110L 2 LIGHT, RED


RS320 REV 2018-01

RS320 - SAFETY CHAIN S000-011 - REV 2007-01

ITEM PART NO. QTY. DESCRIPTION1 S000-011 1 SAFETY CHAIN


RS320 REV 2018-01

RS320 90-010PPrinted in Canada

rs320 - schulte.ca code... · 2 100-3201h 1 cyl. 3x30 tie rod orb ports 3 111-121 2 hyd. hose...

Documents