s-u--media.virbcdn.com/files/18/83f0867fc6eab376-20094_aslp-ul-m-ki… · s-u--doc 24a saa sucs...
TRANSCRIPT
![Page 1: S-U--media.virbcdn.com/files/18/83f0867fc6eab376-20094_ASLP-UL-M-KI… · S-U--Doc 24A SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer](https://reader036.vdocuments.net/reader036/viewer/2022071104/5fdda5918da647596b12bfcf/html5/thumbnails/1.jpg)
SLP-UL-M-KIT
Doc # 20094_A
I N S T A L L A T I O N I N S T R U C T I O N S
Visit our website for more detailswww.CommandAccess.com
U.S. Customer Support1-888-622-2377
Canada Customer Support1-855-823-3002
A.
K it I nc ludesA. 1 - 5/32” Drill BitB. 1- Motor Mount AssemblyC. 1 - 6’ LeadD. 2 -Phillips ScrewsE. 1 - 5/64” Hex Wrench
Tools Required• Power Drill
The Command Access SLP-UL-M-KIT is a field installable motorized latch-pullback kit for the
Sargent 80 series.
B.
C.D.
E.
Scan or Click here
Installation Video
![Page 2: S-U--media.virbcdn.com/files/18/83f0867fc6eab376-20094_ASLP-UL-M-KI… · S-U--Doc 24A SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer](https://reader036.vdocuments.net/reader036/viewer/2022071104/5fdda5918da647596b12bfcf/html5/thumbnails/2.jpg)
STEP 1 - Disassemble Exit DeviceA. Remove End Cap & Filler Plate
B. Remove (4) screws from baserail
C. Partially slide push pad off approx. 2-3”
D. Using 5/32” drill bit. Open up the (2) back screw holes #3 & 4.
![Page 3: S-U--media.virbcdn.com/files/18/83f0867fc6eab376-20094_ASLP-UL-M-KI… · S-U--Doc 24A SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer](https://reader036.vdocuments.net/reader036/viewer/2022071104/5fdda5918da647596b12bfcf/html5/thumbnails/3.jpg)
E. Continue sliding push pad half way out of the base rail so activating bracket is accessible. Next, remove metal rod and AB mount can be put aside.
STEP 2 - Install Motor MountA. Attach the link assembly to the end of the activating bracket. Next, place activating
bracket into center of the motor mount.
C. Re-install metal rod securing activating bracket to motor mount.
B. Secure link assembly to activating bracket with Hex wrench provided.
Activating Bracket Metal RodAB Mount
Link Assembly
Baserail
![Page 4: S-U--media.virbcdn.com/files/18/83f0867fc6eab376-20094_ASLP-UL-M-KI… · S-U--Doc 24A SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer](https://reader036.vdocuments.net/reader036/viewer/2022071104/5fdda5918da647596b12bfcf/html5/thumbnails/4.jpg)
STEP 4 - Install MM3 & Reassemble Device
Next Set the MM3 “PTS” (Push to Set) adjustment. . .
A. Slide push pad with motor kit back into the device. Also, the filler plate must be slid in at some time.
B. Make sure Latch retractor is pressed down so push pad slides over it.
C. Re-install original screws in holes 1 & 2. Install new screws provided in holes 3 & 4.
![Page 5: S-U--media.virbcdn.com/files/18/83f0867fc6eab376-20094_ASLP-UL-M-KI… · S-U--Doc 24A SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer](https://reader036.vdocuments.net/reader036/viewer/2022071104/5fdda5918da647596b12bfcf/html5/thumbnails/5.jpg)
Doc # 20094_A
Visit our website for more detailswww.CommandAccess.com
U.S. Customer Support1-888-622-2377
Canada Customer Support1-855-823-3002
T E C H N I C A L I N F O R M A T I O N
• Input Voltage: Regulated 24VDC +/- 10%• Current Peak: 1 Amp• Current Hold: 125 mA• Wire gauge: X 20 ga
2 Beeps
3 Beeps
5 Beeps
7 Beeps
Beeps Explanation SolutionOver Voltage
Under Voltage
Forced Release
Over-travel or mechanical obstruction
Check voltage & adjust to Regulated 24 V.
Check voltage & adjust to Regulated 24 V.
Device will automatically re-engage within 5 seconds.
Remove obstruction & push pad down until beeping stops & release.
Step 1- Press the device push pad to the desired setting. (this can be fully depressed or less than fully depressed).
Step 2- While depressing the push pad, apply power. (i.e. presenting the credential to the reader).
Step 3- Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the three steps. That’s all there is to it.
Troubleshooting & Diagnostics
Setting Push to Set Adjustment
Specifications
Wiring Color Code