s23&33&53 product introduction (newly added v100r003)-200910

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Internal

www.huawei.com

Introduction to the S23&33&53

(Newly Added V100R003)

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

The S2300 is a new-generation Ethernet switch that can

implement intelligent access at Layer 2 at a rate of 100 Mbit/s.

The S2300 can be applicable to access services of enterprises

and corridors.


implement intelligent access at Layer 3 at a rate of 100 Mbit/s.

The S3300 can be applicable to access and convergence

services of campuses and enterprises.


implement access and convergence at a rate of 1 Gbit/s. The

S5300 can be applicable to convergence services of campuses

and access and convergence services of enterprises.


This course offers you the following information:

Quidway S2300/S3300/S5300 Overview

Quidway S2300 Hardware Structure and Software Features



Quidway S2300/S3300/S5300 Key Features

Quidway S2300/S3300/S5300 Typical Networking


Chapter 1 Quidway S2300/S3300/S5300Chapter 1 Quidway S2300/S3300/S5300 OverviewOverview

Chapter 2 Quidway S2300 Hardware Structure and Software Features



Chapter 5 Quidway S2300/S3300/S5300 Key Features

Chapter 6 Quidway S2300/S3300/S5300 Typical Networking


Positioning of the S2300/S3300/S5300

Ring networking

Access Layer IP/MPLS Core LayerFirst Mile

SoftX

Internet

Headend

VoD Server

BNG/SRS3300

TG/AGBNG/SR

S3300HG

CPE

Metro Ethernet

S5300

MAN

Tree networking

ETTx Solutions Overview

S5300S3300

P

S2300

S2300

S3300

CPE

HG

S9300

S9300

S5300


S5300/S9300S5300/S9300

GEGE

GE Trunk

S2300/S3300

Floor 2 Floor 3Floor 1

GE

DMS RADIUS server

S2300/S3300

Cluster of servers

Firewall

Applications on the medium and large-sized enterprise network

WAN

AR

S2300/S3300

Positioning of the S2300/S3300/S5300


Introduction to the S2300/S3300/S5300

S2309TP

S3328TP

S3352P

运营级接入交换机

Carrier-class campus switch

Gigabit Ethernet switch

S2326TP

S2352P

S2318TP

S5352C-EI

S5352C-PWR-EI

S5328C-EI-24SS5328C-EI

S5328C-PWR-EI

Gigabit convergence

Access convergence

Access

Capacity

S2309TP-PWR-EI

S2326TP-PWR-EI

S3328TP-PWR-EI

S3352P-PWR-EI

S5348TP-SI S5324TP-PWR-SI

S5328C-SI/PWR-SI

S5324TP-SI S5348TP-PWR-SI

New! New!New! New!

New!

New!

New!

New!

100M Ethernet switch

New!New!

The switch marked with New is of a newly developed version, that is, V100R003.

S5352C-SI/PWR-SI

New! New!


Hardware ConfigurationsHardware Configurations

•8*10/100Base-TX,1*Combo GE(10/100/1000Base-T or 100/1000Base-X)•Switching capacity/forwarding rate: 3.6 Gbps/2.68 Mpps•Size:S2309TP-SI/EI: 250(width)*180(depth)*43.6(height)S2309TP-PWR-EI: 320(width)*220 (depth)*43.6 (height)

•Layer 2 Ethernet switch for intelligent access•Providing powerful Ethernet functions for operators or enterprise customers•Meeting requirements for access services of buildings or campuses

Introduction to the S2300

PositioningPositioning


•16*10/100Base-TX,2*Combo GE(10/100/1000Base-T or 100/1000Base-X)•Switching capacity/forwarding rate: 7.2 Gbps/5.36 Mpps•Size: 442 (width)*220 (depth)*43.6 (height)


•24*10/100Base-TX,2*Combo GE

(10/100/1000Base-T or 100/1000Base-X) •Switching capacity/forwarding rate: 8.8 Gbps/6.55 Mpps•Size:S2326TP-SI/EI: 442(width)*220(depth)*43.6(height)S2326TP-PWR-EI: 442 (width)*420 (depth)*43.6 (height)

Hardware ConfigurationsHardware Configurations•S2352P-EI: 48*10/100Base-TX,2*100/1000Base-X SFP,2*1000Base-X SFP•Switching capacity/forwarding rate: 17.6 Gbps/13.1Mpps•Size:S3352P-EI: 442 (width)*220 (depth)*43.6 (height)

•Layer 2 Ethernet switch for intelligent access•Providing powerful Ethernet functions for operators and enterprise customers•Meeting requirements for access services of buildings or campuses






S3352P-EI-48SS3352P-EI-48S

S2352PS2352P

S2326TPS2326TP

S2309TPS2309TP

S2318TP S2318TP



•24*10/100Base-TX,2*1000Base-X SFP,2*Combo GE (10/100/1000Base-T or 100/1000Base-X)•Switching capacity/forwarding rate: 12.8 Gbps/9.6 Mpps•Size:S3328TP-SI/EI: 442(width)*220(depth)*43.6(height)S3328TP-PWR-EI: 442 (width)*420 (depth)*43.6 (height)

•Layer 3 Ethernet switch for intelligent access•Providing powerful Ethernet functions for operators or enterprise customers•Meeting requirements for access services of buildings and access and convergence services of campuses

Introduction to the S3300PositioningPositioning


•24*100Base-FX SFP,2*1000Base-X SFP,2*Combo GE(10/100/1000Base-T or 100/1000Base-X)•Switching capacity/forwarding rate: 12.8 Gbps/9.6 Mpps•Size: 442 (width)*220 (depth)*43.6 (height)


•S3352P-EI-24S: 24*10/100Base-TX,24*100Base-FX SFP,2*100/1000Base-X SFP,2*1000Base-X SFPS3352P-EI-48S: 48*100Base-FX SFP,2*100/1000Base-X SFP,2*1000Base-X SFP •Switching capacity/forwarding rate: 17.6 Gbps/13.1 Mpps•Size: 442 (width)*420 (depth)*43.6 (height)

Hardware ConfigurationsHardware Configurations•48*10/100Base-TX,2*100/1000Base-X SFP,2*1000Base-X SFP•Switching capacity/forwarding rate: 17.6 Gbps/13.1 Mpps•Size:S3352P-SI/EI: 442(width)*220(depth)*43.6(height)S3352P-PWR-EI: 442 (width)*420 (depth)*43.6 (height)







S3352P-PWR-EIS3352P-PWR-EI

S3352P-EI-24SS3352P-EI-24S

S3352P-EI-48SS3352P-EI-48S

S3352P-SI/EIS3352P-SI/EI

S3328TP-EI-24SS3328TP-EI-24S

S3328TP-SI/EIS3328TP-SI/EI

S3328TP-PWR-EI S3328TP-PWR-EI



•24*10/100/1000Base-T,4*1000Base-X combo SFP (constituting four combo interfaces with the last four RJ45 connectors)•Switching capacity/forwarding rate: 48 Gbps/36 Mpps•Size:S5324TP-SI: 442 mm x 220 x 43.6 mm (width x depth x height)S5324TP-PWR-SI: 442 mm x 420 mm x 43.6 mm (width x depth x height)

•Layer 3 gigabit Ethernet switch for intelligent access•Providing powerful Ethernet functions for operators or enterprise customers•Meeting requirements for access services of buildings, access and convergence services of campuses, and desktop services of enterprises.

Introduction to the S5300TP



•48*10/100/1000Base-T,4*1000Base-X combo SFP (constituting four combo interfaces with the last four RJ45 connectors) •Switching capacity/forwarding rate: 96 Gbps/72 Mpps•Size: 442 mm x 420 mm x 43.6 mm (width x depth x height)

•Layer 3 gigabit Ethernet switch for intelligent access•Providing powerful Ethernet functions for operators or enterprise customers•Meeting requirements for access services of buildings, access and convergence services of campuses, and desktop services of enterprises.


S5348TP-PWR-SIS5348TP-PWR-SI

S5348TP-SIS5348TP-SI


S5324TP-PWR-SI S5324TP-PWR-SI



•24*10/100/1000Base-T,upstream card(4*1000Base-X SFP or 2*10GE XFP), stacking card•Switching capacity/forwarding rate: 88 Gbps/66 Mpps•Double hot-swappable power modules•Size: 442(width)*420(depth)*43.6(height)

•Layer 3 Ethernet switch for intelligent access•Providing powerful Ethernet functions for operators or enterprise customers•Meeting requirements for convergence services of campuses and access and convergence services of enterprises

Introduction to the S5300C








S5352C-PWR-SIS5352C-PWR-SI

S5328C-SIS5328C-SI S5328C-PWR-SIS5328C-PWR-SI

S5352C-SIS5352C-SI

S5352C-EIS5352C-EI

S5328C-EIS5328C-EI S5328C-PWR-EI S5328C-PWR-EI

S5352C-PWR-EIS5352C-PWR-EI•48*10/100/1000Base-T,upstream card(4*1000Base-X SFP or 2*10GE XFP), stacking card•Switching capacity/forwarding rate: 136 Gbps/102 Mpps•Double hot-swappable power modules•Size: 442(width)*420(depth)*43.6(height)

•24*10/100/1000Base-T,4*1000Base-X combo SFP, upstream card(4*1000Base-X SFP or 2*10GE XFP), stacking card•Switching capacity/forwarding rate: 88 Gbps/66 Mpps•Double hot-swappable power modules•Size: 442(width)*420(depth)*43.6(height)

•48*10/100/1000Base-T, upstream card(4*1000Base-X SFP or 2*10GE XFP), stacking card•Switching capacity/forwarding rate: 136 Gbps/102 Mpps•Double hot-swappable power modules•Size: 442(width)*420(depth)*43.6(height)





Chapter 1 Quidway S2300/S3300/S5300 Overview

Chapter 2 Quidway S2300 Hardware Structure and Software FeaturesChapter 2 Quidway S2300 Hardware Structure and Software Features






Models of the S2300

The models of the S2300 are described as follows:

The S2309TP-SI/EI provides 8 FE electrical interfaces and 1 GE combo interface and supports AC and DC power.

The S2318TP-SI/EI provides 16 FE electrical interfaces and 2 GE combo interfaces and supports AC and DC power.

The S2326TP-SI/EI provides 24 FE electrical interfaces and 2 GE combo interfaces and supports AC and DC power.

The S2352P-EI provides 48 FE electrical interfaces and 4 GE optical interfaces and supports AC and DC power.

The S2309TP-PWR-EI provides 8 FE electrical interfaces and 1 GE combo interface and supports AC power. The FE

electrical interfaces support PoE.

The S2326TP-PWR-EI provides 24 FE electrical interfaces and 2 GE combo interfaces and supports AC power. The FE

electrical interfaces support PoE.


Features of the Non-PoE Model of the S2300

The S2300 functions as a Layer 2 switch.

Upstream interfaces are combo interfaces that can flexibly function as electrical interfaces or

optical interfaces.

Each service interface provides a link/act indicator to indicate the status of the running

services.

The device is small in size and can be easily placed, which reduces the construction costs for

operators.

The device boasts low power consumption and environment friendliness.

There is no fan and no noise.

Service interfaces on non-PoE models boast high lightening protection capabilities, that is, 6

kV in common mode.

The device is installed with built-in power modules, which facilitates the installation of the

device.


Figure of the Non-PoE model of the S2300

AC power

1U 44.45 mm

24*100M electrical interface

2 GE Combo

Console interface

S2326TP-SI/EI:

GE Combo

Console interface


AC power

1U 44.45 mm

S2309TP-SI/EI:


Features of the PoE Model of the S2300

The S2300 functions as a Layer 2 switch.

Upstream interfaces are combo interfaces that can flexibly function as electrical interfaces or optical interfaces.

Downstream interfaces support remote power supply, with the maximum output power as 15.4 W for each interface.

Each service interface provides an indicator whose mode can be switched among link/act, PoE, and speed through the mode button on the right.

The fans are hot-swappable, which facilitates on-site replacement and maintenance.

The fans can automatically adjust the rotational speed according to the temperature, which reduces power consumption.

The device is installed with double slots so that the power module can be backed up.

The power modules are swappable, which facilitates the maintenance.

The PoE power supply has two output voltages, that is, 12 V and 53 V. The voltage of 12 V provides power for the local device and the voltage of 53 V provides PoE power for the remote PD.

The PoE power supply has two power specifications, that is, 250W (120 W for 12 V voltage and 130 W for 53 V voltage) and 500W (120 W for 12 V voltage and 380 W for 53 V voltage). The 250 W power module provides full power for 8 interfaces and the 500 W power module provides full power for 24 interfaces.


Each interface supports the maximum output

power of 15.4 W, compliant with IEEE 802.3af.

Mode button: You can press this button to

switch the mode of the downstream interface

indicator among link/act, speed, and PoE.

24*100M PoE electrical interface Console interface

Mode button and indicator

Fan slot:

40mm fan x 2

Auto speed adjustment

Hot-swappable

Double power slots

AC and DC power

PoE and non-PoE power

Hot swappable

All the devices of the PoE model except the

S2309TP-PWR-EI provide double slots for

power modules.

The PoE power has two specifications, that

is, 250 W AC power and 500 W AC power.

Note: Only the S2309TP-PWR-EI provides one built-in PoE power module.

Upstream GE combo interfaceS2326TP-PWR-EI

S2326TP-PWR-EI

Figure of the PoE model of the S2300


Specifications of the S2300-EI

Flexible Security Control

Strong QoS & ACL

4 priority queues per port SP/WRR/SP+WRR queue

scheduling 802.1p and IP-Precedence

priorities Port-based rate limiting with the

minimum granularity of 64kbps Priority mapping / priority marking TCAM based ACL Port based & VLAN based ACL CAR （ SrTCM 、 TrTCM ）

Abundant Security Policy

QinQ Voice VLAN VLAN Mapping MVLAN+ IGMP v1 v2 snooping IGMP v3 snooping LACP

8k MAC address 4k VLAN 1k ACL number

Dynamic ARP Inspection Static ARP Inspection ARP rate limit IP Source Guard DHCP snooping DHCP snooping option82

HGMP v2 SNMP v1/v2/v3 RMON (Remote Monitoring) v1 IEEE 802.3ah IEEE 802.1ag Auto Config

Network Management

Red font is only for V1R3


Specifications of the S2300-SI


Strong QoS & ACL






IGMP v1 v2 snooping IGMP v3 snooping LACP

8k MAC address 4k VLAN ARP rate limit

HGMP v2 SNMP v1/v2/v3 RMON (Remote Monitoring) v1 Auto Config

Network Management



Structure of the S2300TP

442

220Main board

43.6

(1) The downstream FE interfaces support 10M/100M auto-sensing.

(2) Two upstream GE combo interfaces and the optical interfaces support 100M/1000M auto-sensing, and the electrical interfaces support 10M/100M/1000M auto-sensing.

(3) The chassis of the S2309 is 1 U high with the dimensions of 250 mm x 180 mm (width x depth).

(4) The chassis of the S2318/S2326TP is 1 U high, 220 mm deep, and 19 inch wide.

(5) The device supports line-rate switching.

(6) The device supports natural heat dissipation.

(7) The power supply interface is installed on the front panel, which facilitates the maintenance of the device. AC power and DC power are supported.

(8) The power supply interface of the S2352P is installed at the back.

The S2309TP provides 8 FE electrical interfaces, 1 GE combo interface, and 1 console interface, with the height of 1 U.

The S2318TP provides 16 FE electrical interfaces, 2 GE combo interfaces, and 1 console interface, with the height of 1 U.

The S2326TP provides 24 FE electrical interfaces, 2 GE combo interfaces, and 1 console interface, with the height of 1 U.

The S2352P provides 48 FE electrical interfaces, 4 GE SFP interfaces, and 1 console interface, with the height of 1 U.

Power

Downstream service interface

Upstream service interface

Console interface


Hardware Structure of the S2300

The scheme of the card on the S2300 is displayed as follows:

442

220

43.6

Systempower

CPU

Switch

DDR DRAM

DDR DRAM

flash

GE PHY

FE J45 GE combo




Chapter 3 Quidway S3300Chapter 3 Quidway S3300 Hardware Structure and Software FeaturesHardware Structure and Software Features





Models of the S3300

The models of the S3300 are described as follows:

The S3328TP provides 24 FE electrical interfaces, two 1000BASE-X optical interfaces, and two GE combo interfaces.

The S3328TP-24S provides 24 FE optical interfaces, two 1000BASE-X optical interfaces, and two GE combo interfaces.

The S3352P provides 48 FE electrical interfaces, two 1000BASE-X optical interfaces, and two 100/1000BASE-X optical interfaces.

The S3352P-24S provides 24 FE electrical interfaces, 24 FE optical interfaces, two 1000BASE-X optical interfaces, and two 100/1000BASE-X optical interfaces.

The S3352P-48S provides 48 FE optical interfaces, two 1000BASE-X optical interfaces, and two 100/1000BASE-X optical interfaces.

The S3328TP-PWR-EI provides 24 FE electrical interfaces, two 1000BASE-X optical interfaces, and two GE combo interfaces. The FE electrical interfaces support PoE.

The S3352P-PWR-EI provides 48 FE electrical interfaces, two 1000BASE-X optical interfaces, and two 100/1000BASE-X optical interfaces. The FE electrical interfaces support PoE.

The non-POE models of the S3300 support AC and DC power, and the PoE models of the S3300 support only AC power.

The positioning of the S3300 is displayed as follows:

Switch for access services and convergence services of corridors, campuses, or equipment room


Introduction to the S3300

Appearance of the S3300


Features of the Non-PoE model of the S3300

The S3300 functions as a Layer 3 100M switch.

The S3328 provides two combo interfaces that can flexibly function as optical interfaces or

electrical interfaces.

Each service interface provides a link/act indicator to indicate the status of the running

services.

The device is 220 mm high and small in size, and thus can be easily placed. This reduces the

construction costs for operators.

The device boasts low power consumption and environment friendliness.

Service interfaces on non-PoE models boast high lightening protection capabilities, that is, 6

kV in common mode.

The device is installed with built-in power modules, which facilitates the installation of the

device.


Figure of the Non-PoE Model of the S3300

AC power

24*100M electrical interface GE combo

Console interface

S3328TP-SI/EI

GE SFP

Console interface


1U 44.45 mm

S3352P-SI/EI

1000M SFP or stack interface

1U 44.45 mm

Note: The first two GE SFP interfaces can also be used as stack interfaces.


Features of the PoE Model of the S3300The S3300 functions as a Layer 3 switch.

Downstream interfaces support remote power supply, with the maximum output power as 15.4 W for each interface.

Each service interface provides an indicator whose mode can be switched among Link/Act, PoE, Speed, and Stack through the mode button on the right.

The fans are hot-swappable, which facilitates on-site replacement and maintenance.

The fans can automatically adjust the rotational speed according to the temperature, which reduces power consumption.

The product is installed with double slots so that the power supply can be backed up.

The power modules are swappable, which facilitates the maintenance.

The PoE power supply has two output voltages, that is, 12 V and 53 V. The voltage of 12 V provides power for the local device and the voltage of 53 V provides PoE power for the remote PD.

The PoE power supply has two power specifications, that is, 250W (120 W for 12 V voltage and 130 W for 53 V voltage) and 500W (120 W for 12 V voltage and 380 W for 53 V voltage). The 250 W power module provides full power for 8 interfaces and the 500 W power module provides full power for 24 interfaces. Two 500 W power modules can provide full power for 48 interfaces.


Each interface supports the maximum output

power of 15.4 W, compliant with IEEE 802.3af.

Mode button: You can press this button to

switch the mode of the downstream interface

indicator among link/act, speed, and PoE.

24*100M PoE electrical interface

Console interface


Fan slot:

40mm fan x 2


Hot-swappable

Double power slotsAC and DC powerPoE and non-PoE powerHot-swappable

All the devices of the PoE model provide

double slots for power modules. Two PoE

power modules installed in the slots can

provide full power for 48 interfaces,

The PoE power has two specifications, that


Upstream GE comboS3328TP-PWR-EI

S3328TP-PWR-EI

Figure of the PoE Model of the S3300

Upstream GE SFP or stack interface




Strong QoS & ACL






VRRP RIP/OSPFv2/IS-IS/BGP PIM/MSDP RIPng/OSPFv3 MCE

QinQ & Selective QinQ Voice VLAN VLAN Mapping MVLAN+ IGMP snooping LACP Smartlink/RRPP


Dynamic ARP Inspection Static ARP Inspection ARP rate limit IP Source Guard DHCP snooping DHCP snooping option82 BFD for Static

route/ISIS/OSPF/BGP Sticky MAC

HGMP v2 SNMP v1/v2/v3 RMON (Remote Monitoring) v1 IEEE 802.3ah IEEE 802.1ag DHCP Server/Relay Auto Config Stacking

Network Management





Strong QoS & ACL






RIP RIPng



Dynamic ARP Inspection Static ARP Inspection ARP rate limit IP Source Guard DHCP snooping DHCP snooping option82 Sticky MAC


Network Management



Structure of the S3328TP

442

220Main board

43.6

(1) Downstream FE interfaces support 10M/100M auto-sensing.

(2) The device provides two upstream SFP 1000M optical interfaces.

(3) The device provides two upstream GE combo interfaces that support 100M/1000M auto-sensing.

(4) The chassis of the product is 1 U high, 220 mm deep, and 19 inch wide.

(5) The electrical interfaces support natural heat dissipation and the optical interfaces support air-cooling heat dissipation.

(6) The power supply interface is installed on the front panel, which facilitates the maintenance of the device. AC power and DC power are supported.

The S3328TP provides 24 FE electrical interfaces, 2 GE optical interfaces, 2 GE combo interfaces, and 1 console interface, with the height of 1 U.

The S3328TP-24S provides 24 FE optical interfaces, 2 GE optical interfaces, 2 GE combo interfaces, and 1 console interface, with the height of 1 U.

Power


Structure of the S3352P

442

420Main board

43.6

(1) Downstream FE interfaces support 10M/100M auto-sensing.

(2) The device provides four SFP optical interfaces, two of which support 100M/1000M auto-sensing.

(3) The chassis of the product is 1 U high, 420 mm deep, and 19 inch wide. The chassis of the 3352P is 220 mm deep.

(4) The product supports air-cooling heat dissipation.

(5) The AC power and DC power are supported.

Power

The S3352P provides 48 FE electrical interfaces, 4 GE optical interfaces, and 1 console interface, with the height of 1 U and depth of 220 mm.

The S3352P-24S provides 24 FE electrical interfaces, 24 FE optical interfaces, 4 GE optical interfaces, and 1 console interface, with the height of 1 U and depth of 420 mm.

The S3352P-48S provides 48 FE optical interfaces, 4 GE optical interfaces, and 1 console interface, with the height of 1 U and depth of 420 mm.


Structure of the S3300-PWR

442

420

43.6

PoE powe

r

PoE powe

r

Fan frame

Main board

(1) The chassis of the product is 1 U high, 420 mm deep, and 19 inch wide.

(2) The product provides two power modules and supports the AC power.

(3) The fans are hot-swappable.




442

220

43.6

Systempower

SWITCH(Int cpu)

DDR DRAM

DDR DRAM

flash

GE PHY

FE J45 GE combo

FE PHY FE PHY FE PHY




442

420

System power

Switch

DDR DRAM

DDR DRAMflash

GE PHY

FE J45 GE combo

FE PHY

FE PHY

FE PHY

CPU

Switch

FE PHY

FE PHY

FE PHY



442

420

43.6

PoE powe

r

PoE powe

r

Fan frame

Switch

cpu

FE PHY FE PHY

DRAM

flash

DRAM

The scheme of the card on the S3328TP-PWR-EI is displayed as follows:

(1) The dimensions of the product are 442 mm x 420 mm x 43.6 mm (width x depth x height).

(2) The device provides two power slots. When one 500 W power module is installed, it provides full power for 24 interfaces with the maximum output power of each interface as 15.4 W; when two power modules are installed, the card power supply of 12 V voltage and the PoE power supply are backed up in 1+1 mode.

(3) The power module is swappable and supports on-site maintenance.

(4) The device supports the AC power.

(5) The device supports air-cooling heat dissipation.



442

420

43.6

PoE powe

r

PoE powe

r

Fan frame

Switch

FE PHY FE PHY

DRAM

flash

DRAMSwitc

hcpu

Switch

The scheme of the card on the S3352P-PWR-EI is displayed as follows:


(1) The dimensions of the device are 442 mm x 420 mm x 43.6 mm (width x depth x height).

(2) The device provides two power slots. When one 500 W power module is installed, it provides full power for 24 interfaces with the maximum power of each interface as 15.4 W; when two 500 W power modules are installed, they provide full power for 48 interfaces with the maximum output power of each interface as 15.4 W.

(3) When two power modules are installed, the card power supply of 12 V voltage can be backed up in 1+1 mode.


(5) The device supports AC power.

(6) When two power modules are installed to provide full power for 24 interfaces, the card power supply and the PoE power supply can be backed up in 1+1 mode.







Chapter 4 Quidway S5300Chapter 4 Quidway S5300 Hardware Structure and Software FeaturesHardware Structure and Software Features




Introduction to the S5300CThe models of the S5300C are described as follows:

The S5328C-EI/PWR-EI provides 24 GE electrical interfaces and 1 slot where a card with four

GE optical interfaces or two 10GE interfaces can be installed.

The S5328C-24S-EI provides 24 GE optical interfaces, 4 GE combo electrical interfaces, and 1

slot where a card with four GE optical interfaces or two 10GE interfaces can be installed.

The S5352C-EI/PWR-EI provides 48 GE electrical interfaces and 1 slot where a card with four


The S5328C-SI/PWR-SI provides 24 GE electrical interfaces, 4 GE combo optical interfaces, and

1 slot where a card with four GE optical interfaces or two 10GE interfaces can be installed.

The S5352C-SI/PWR-SI provides 48 GE electrical interfaces and 1 slot where a card with four


The preceding devices of the PWR model support PoE on the downstream interfaces.

The dimensions of the device are 442 mm x 420 mm x 43.6 mm (width x depth x height).



The positioning of the S5300C is displayed as follows:

Switch for convergence services of campuses, equipment room, or enterprises

S5328C-SI/PWR-SIS5328C-SI/PWR-SI

S5352C-SI/PWR-SIS5352C-SI/PWR-SI



The main features of the S5300C are described as follows:

The device supports double power modules in 1+1 redundancy mode. In redundancy mode, the power module can be replaced with the services running normally.

The device supports the AC and DC power. The device of the PWR model supports only the AC power.

The upstream interfaces support flexible cards with four GE optical interfaces or two 10GE XFP interfaces.

The power modules, fans, and upstream service cards support on-site replacement.

The device supports rear cards for stacking.

If a front card with four GE optical interfaces is installed on the device, stacking is not supported.


Mode button: You can press this button to switch the mode of the

downstream interface indicator among link/act, speed, and stack.

The card with four GE interfaces and the stack card cannot be

used at the same time.

The length of the stack cable is 1 m.

The power has two specifications, that is, 150 W AC power and

150 W DC power.

GE electrical interfaceConsole interface


Fan slot:

40mm fan × 2


Hot-swappable

Double power slots

AC and DC power

Hot-swappable

• S5328C-SI

Figure of the Non-PoE Model of the S5300C

Upstream service card with four GE SFP interfaces or two 10GE XFP interfaces

Management Ethernet interface

Rear slot:

Stacking card

Note: Only the SI model has USB interfaces.


Mode button: You can press this button to switch the mode of the downstream

interface indicator among link/act, speed, stack, and PoE.

Each interface supports the maximum output power of 15.4 W, compliant with IEEE

802.3af.

The card with four GE interfaces and the stack card cannot be used at the same

time.


GE PoE electrical interfaceConsole interface


Fan slot:

40 mm fan × 2


Hot-swappable

Double power slots

AC power and DC power

PoE power and non-PoE power

Hot-swappable

The PoE model provides double power slots. Two

500 W PoE power modules can be installed to

provide full PoE power for 48 interfaces.

The PoE power has two specifications, that is, 250

W AC power and 500 W AC power.

GE combo interface

• S5328C-PWR-SI

Figure of the PoE Model of the S5300C

Upstream service card with four GE SFP interfaces or two 10GE XFP interfaces


USB interface

Rear slot:

Stack card

Note: Only the SI model has USB interfaces.


Hardware Specifications of the S5300C




Strong QoS & ACL






VRRP RIP/OSPFv2/IS-IS/BGP PIM/MSDP RIPng/OSPFv3 MCE/uRPF


32k MAC address 4k VLAN 5.5k ACL number

Dynamic ARP Inspection Static ARP Inspection ARP rate limit IP Source Guard DHCP snooping DHCP snooping option82 BFD for Static

route/ISIS/OSPF/BGP Sticky MAC


Network Management





Strong QoS & ACL






RIP RIPng uRPF





Network Management



Structure of the S5352C

442

420

43.6

Power supply

Power supply

Fan frame

The device provides 48 GE electrical interfaces, two upstream cards, one console interface, and double power modules (AC power and DC power), with the height of 1 U.

(1) Downstream GE interfaces support 10M/100M/1000M auto-sensing.

(2) The upstream interfaces support flexible cards with four GE optical interfaces or two 10GE interfaces.

(3) The chassis of the device is 1 U high, 420 mm deep, and 19 inch wide.


(5) Upstream interfaces support flexible cards.

(6) The power module can be backed up in 1+1 mode.


Stack card

Front card

Switch Switch

FE PHY FE PHY

CPU DRAMflash

DRAM


Structure of the S5328C

The device provides 24 GE electrical interfaces, two upstream cards, one console interface, and double power modules (AC power and DC power), with the height of 1 U.






(6) The fans are hot-swappable. 442

420

43.6

Power supply

Power supply

Fan frame

Stack card

Front card

Switch

FE PHY FE PHY

CPU DRAMflash

DRAM


Structure of the S5328C-24S

442

420

Main board

43.6

Power supply

Power supply

Fan frame

The device provides 20 GE electrical interfaces, four GE combo interfaces, two upstream cards, one console interface, and double power modules (AC power and DC power), with the height of 1 U.







Stack card

Front card


Structure of the S5328C/52C-PWR

442

420

Main board

43.6

PoE power

PoE power

Fan frame

Stack card

Front card


(2) The device provides double power slots. One 500 W power module provides full power for 24 interfaces and two 500 W power modules provide full power for 48 interfaces, with the maximum output power of each interface as 15.4 W.




(6) When two power module are installed to provide full power for 24 interfaces, the card power supply and PoE power supply can be backed up in 1+1 mode.





The models of the S5300TP are described as follows:

The S5324TP-SI provides 24 GE electrical interfaces and 4 GE combo optical interfaces. AC

power and DC power are supported.

The S5348TP-SI provides 48 GE electrical interfaces and 4 GE combo optical interfaces. AC

power and DC power are supported.

The S5324TP-PWR-SI provides 24 GE electrical interfaces and 4 GE combo optical

interfaces. Only AC power is supported.

The S5348TP-PWR-SI provides 48 GE electrical interfaces and 4 GE combo optical

interfaces, Only AC power is supported.

The overall structure of the device is displayed as follows:

The dimensions of the S5324TP-SI are 442 mm x 220 mm x 43.6 mm (width x depth x height).

The dimensions of the S5348TP-SI/ S5324TP-PWR-SI / S5348TP-PWR-SI are 442 mm x 420

mm x 43.6 mm (width x depth x height).



The positioning of the S5300TP is displayed as follows:

Switch for the convergence services of campuses, equipment room, or enterprises







The main features of the S5300TP are described as follows:

The device is a low-cost Gigabit Ethernet switch.

The Non-PWR model supports RPS redundancy power modules. The

PWR model supports double power modules.

The device supports rear cards for stacking.


Mode button: You can press this button to switch

the mode of the downstream interface indicator

among link/act, speed, and stack.


RPS redundancy power modules are supported.

RPS powerConsole interface

Mode button and indicator• S5324TP-SI

Figure of the Non-PoE Model of the S5300TP

GE combo interface


Rear slot:

Stack card

GE electrical interface

Power supply

USB interface


Mode button: You can press this button to switch

the mode of the downstream interface indicator

among link/act, speed, stack, and PoE.


The fan modules are hot-swappable.

Console interface


Fan slot:

40 mm fan × 2


Hot-swappable

Double power slots

AC power and DC power

Hot-swappable

• S5324TP-PWR-SI

The PoE Model of the S5300TP

GE combo interface


Rear slot:

Stack card


USB interface

The PoE model provides double power slots. Two

500 W PoE power modules can be installed to

provide full power for 48 interfaces.

The PoE power supply has two specifications, that



Hardware Specifications of the S5300TP


Specifications of the S5300TP


Strong QoS & ACL






RIP RIPng uRPF





Network Management


Hardware Structure of the S5324TP

442

220

43.6

Systempower

SWITCH(Int cpu)

DDR DRAM

DDR DRAM

flash

24GE J45 4GE combo

GE PHY GE PHY GE PHY

Stack card


Hardware Structure of the S5348TP

The scheme of the card on the S5348TP is displayed as follows:

442

420

System power

Switch

DDR DRAM

DDR DRAM

flash

48GE J45 4GE combo

GE PHY

GE PHY

GE PHY

Switch

GE PHY

GE PHY

GEPHY

Stack card


Structure of the S5324TP/48TP-PWR-SI

442

420

Main board

43.6

PoE power

PoE power

Fan frame

Stack card


(2) The device supports double power modules. One 500 W power module provides full power for 24 interfaces and two 500 W power modules provide full power for 48 interfaces, with the maximum output power of each interface as 15.4 W.


(4) The power modules are swappable and support on-site maintenance.


(6) When two power modules are installed to provide full power for 24 interfaces, the card power supply and PoE power supply can be backed up in 1+1 mode.


(8) The fan modules are hot-swappable.


Interface on the S2300/S3300/S5300 — FE Electrical Interface

Common Interface

FE electrical interface

Form: RJ45

Rate: 10M/100M

Protocol: Ethernet


Interface on the S2300/S3300/S5300 — FE SFP Optical Interface

Common Interface

FE optical interface

Form: SFP and LC

Rate: 100M

Protocol: Ethernet


Interface on the S2300/S3300/S5300 — FE Single-fiber Bidirectional Optical Interface

Special Interface

FE Single-fiber Bidirectional Optical

Interface

Form: SFP, LC, and single fiber

Rate: 100M

Protocol: Ethernet

Figure of the SFP single-fiber bidirectional moduleFigure of the SFP single-fiber bidirectional module


Interface on the S2300/S3300/S5300 — GE Electrical Interface

Common Interface


Form: RJ45

Rate: 10M/100M/1000M

Protocol: Ethernet


Interface on the S2300/S3300/S5300 — GE SFP Optical Interface

Common Interface

GE optical interface

Form: SFP and LC

Rate: 1000M

Protocol: Ethernet


Interface on the S2300/S3300/S5300 — 10GE XFP Optical Interface

Common Interface

10GE XFP optical interface

Form: XFP and LC

Rate: 10.3125 Gbps

Protocol: Ethernet


Interface on the S2300/S3300/S5300 — GE WDM Interface

Special Interface

GE CWDM optical interface

Form: SFP and LC

Rate: 1000M

Protocol: Ethernet


Interface on the S2300/S3300/S5300 — GE Single-fiber Bidirectional Optical Interface

Special Interface

GE single-fiber bidirectional optical

interface

Form: SFP, LC, and single fiber

Rate: 1000M

Protocol: Ethernet

Figure of an SFP single-fiber bidirectional moduleFigure of an SFP single-fiber bidirectional module






Chapter 5 Quidway S2300/S3300/S5300Chapter 5 Quidway S2300/S3300/S5300 Key FeaturesKey Features



User-friendly NMS

Value for customers:The NMS provides a graphical interface and simplified operation procedures and prompts, which reduces costs of training the NMS staff.You can complete configurations just by clicking the mouse. This shortens the configuration duration and improves the configuration efficiency.

Intranet


Value for customers: The switch supporting PoE is applicable to various scenarios, thus solving the problem of power supply.

The terminal can be deployed flexibly without the restriction of cabling for the power supply. This reduces the costs of the terminal deployment.

PoE redundancy power is provided to meet requirements of traffic cameras and wireless access management for high availability.

Various PoE Applications

PoE device

PoE device

AP

AP

Home access

Hot spot area

Building access

Video monitoring

PoE device

Wireless Access Management

Control Center

MetroPoE device

camera

AP


Stacking

S5300 S3300 S2300

Supported topology Ring topology Ring topology Link topology

Switching capacity of a

stack interface

24 Gbps

48 Gbps (dual interfaces)

5 Gbps

10 Gbps (dual interfaces)

2 Gbps

Maximum number of

switches in a stack

9 9 16

Stack interface Specialized stack interface Also an upstream GE

interface

None

Stack cable Specialized for the S5300 Specialized for the S3300 Common network cable or

optical fiber

Principle of stacking Hardware stack Hardware stack Software stack

Stack cables, similar to the backplane of the cabinet-shaped switch

Master switch, similar to the active SCU on the cabinet-shaped switch

Slave switch, similar to the LPU on the cabinet-shaped switch

As shown in the figure, multiple case-shaped switches form a stack, which is similar to a cabinet-shaped switch.Standby switch, similar

to the standby SCU on the cabinet-shaped switch







Chapter 6 Quidway S2300/S3300/S5300Chapter 6 Quidway S2300/S3300/S5300 Typical NetworkingTypical Networking


Networking of ETTx

Ring networking

Access Layer IP/MPLS Core LayerFirst Mile

SoftX

Internet

Headend

VoD Server

BNG/SRS3300

TG/AGBNG/SR

S3300HG

CPE

Metro Ethernet

S5300

MAN

Tree networking

ETTx provides solutions for individual users and leased line users.

Services for individual users: HSI, VoIP, and VOD/BTV

Services for leased line users: VPN services at Layer 2 and Layer 3 and high-speed Internet services

S5300S3300

P

S2300

S2300

S3300

CPE

HG

S9300

S9300

S5300


Applications in Large and Medium-sized Enterprise Networking

S5300/S9300S5300/S9300

GEGE

GE Trunk

S2300/S3300

Floor 2 Floor 3Floor 1

GE

DMS Radius server

S2300/S3300

Cluster of servers

Firewall

Large capacity: The S5300 or S9300 of large capacity is used to ensure the rate of 1000M on floors.High availability: VRRP is run on two core switches to realize the backup mode.

Double links are used to converge services at each floor to the core switches. High security: The terminal needs to pass the RADIUS authentication before accessing the network. The Eudemon is deployed at the edge of servers to ensure the security of servers.

WAN

AR

S2300/S3300

Thank you!

www.huawei.com

s23&33&53 product introduction (newly added v100r003)-200910

Documents