safety is our 1st priority lp-gas pressure regulator€¦ · lp-gas pressure regulator safety is...
TRANSCRIPT
LP-GASPRESSURE REGULATOR
Safety is our 1st Priority
HYR SINGLE STAGE REGULATOR 14
HYRM SERIES REGULATOR 16
HYR SECOND STAGE REGULATOR 22
2000 SERIES REGULATOR 26
AUTOMATIC CHANGEOVER PRESSURE REGULATOR 28
LIQUID CHANGEOVER DEVICE (HLX-301) 32
HWA YOUNG GAS HOSE 34
8
B O X
B O X
Precaution of installation
• The regulator should be installed by qualifi ed and trained technician
• THIS PRODUCT is MADE FOR USING LP-GAS ONLY. Do not use other than LP gas. Unless it can degrade original performance down
• This product is accurate assembled and set so that NEVER disassemble or modifi ed without a professionally trainer’s permission. Prior installing the regulator, check the damage which might have occurred in shipment. Also check for dirt or foreign matter which may have accumulated in the regulator body or in the pipelines. Please check the product in appearances before installation, Failure of product may cause of hazardous condition.
• In case of installing indoor, a regulator must avoid rain, snow, or direct sunlight. Set appropriate protection where a product can be expose long period of time from sunlight and water. indoor installation must be considered proper ventilation system.
• DO NOT install a regulator where fl ammable materials are loaded or near radiant heat.
• Avoid installation at a place where can be affected on regulator from suspectible gas such as ammonia (NH3), sulfurous acid gas (SO2) etc.
• Connecting inlet to a pigtail or vent pipe, it should remains balance vertically.
• Inappropriate piping connection can occur at the time of installation when connected loosely or the regulator may have been overstressed by excessive wrenching.
• Screw threads of inlet should be connected with an exclusive adaptor.
• Use PTFE (Tefl on) or fl ame retardant vent glue on the screw threads, it helps to prevent loose, gas leakage.
• At the time of installation, be aware of foreign materials would be inserted.
• Remove scraps, dust, any foreign substances and clean cutting fl uid out when connecting unit to a vent pipe.
• Install a gas drain from regulator outlet to a gas meter.• Regulators should be installed with the vent facing down
or protected so their operation will not be affected by the natural elements.
• Before installing the regulator, check the damage which might have occurred in shipment. Also check for dirt
Procedure
• Replacing a gas cylinder, must inspect the indicator and follow below procedure. (1) When indicator turned in red, (assuming indicator
direction is serve) gas is being supplied from the reserve cylinder.
(2) Closing valve from the service and high pressure pipe valve, and turn indicator to opposite.
(3) Note that do not replace a gas cylinder without procedures above.
Maintenance
* in order to prevent water damage, appropriate protection should be required such as waterproof, ** Regulators should be installed with the vent facing down or protected with so that operation will not be affected by the elements*** Remove scraps, dust, any foreign substances in the vent line.
The Guideline of the products
DANGER
or foreign matter which may have accumulated in the regulator body or in the pipelines. Please check the product in appearances before installation, Failure of product may cause of hazardous condition.
www.hwa-young.com
98
Caution• The regulator should be installed by qualified and trained
technician• THIS PRODUCT MADE FOR USING LP-GAS ONLY. Do not
uses other than LP gas, unless it can degrade original performance down
• Before installing the regulator, check the damage which might have occurred in shipment. Also check for dirt or foreign matter which may have accumulated in the regulator body or in the pipelines. Please check the product in appearances before installation, Failure of product may
Requirement of customizing (specific information must be given before manufacturing the regulator)1. Inlet and outlet specific size. 2. Name of model 3. Demand outlet pressure4. Range of inlet pressure.
• After all pressure has been released from the regulator, check an indicator point to proper direction (either serve or reserve), then inspect that there is a gas leak in the cylinder valve, inlet fitting, high pressure hose, or regulator seat.
• Do not attempt to load any heavy matters on the regulator for safety issue.
• Maintenance operation does not required removal of valve body from the line.
• Maintenance should be carried out only by qualified, and professional trained technician.
• A convert handle indicates “serve”, otherwise “reserve”. Refill or replace the gas cylinders for both sides.
• In order to find out regulator operates without defective problem. Please follow procedure below:1) Reserve offers gas to regulator when closed valve from
the serve, causing exhausted gas by the serve making noise sounds. (Sounds from the diaphragm)
2) This sound specifies gas flows into regulator properly and process without problem.
3) Check an indicator signify red. After that revolve the “convert handle” slowly to opposite direction to observe indicator turns to colorless.
4) Though out those procedures, observe and redo the procedure whether changeover process working properly by opening valve from the serve and closing valve from reserve.
cause of hazardous condition.• Do not let vent clog from the elements, and do not let any
dirt, water, or rain into a vent.• This product is accurate assembled and set so that NEVER
disassemble or modified without a professionally trainer’s permission. Prior installing the regulator, check the damage which might have occurred in shipment. Also check for dirt or foreign matter which may have accumulated in the regulator body or in the pipelines. Please check the product in appearances before installation, Failure of product may cause of hazardous condition
• DO NOT install a regulator where flammable materials are loaded or near radiant heat
• Avoid installation at a place where can be affected on regulator from suspectible gas such as such as ammonia (NH3), sulfurous acid gas (SO2) etc.
• Avoid installation where a regulator exposed to salt air, industrial poison, or chemically effective environment. If a regulator has to install in those conditions, follow instruction below.
NOTE: Regulator inspection for corrosion should be made every a year
Gas Tank InstallationWhen install regulator on gas tank, the regulator must be covered. Use the vent pipe face downward when installation. Make sure the regulator not to expose.
Check before using (Leakage & Operation) • After installation the leakage test must be carried out
based on LP gas safety policy.• Get rid of all air out of pipe after checking if there is no
flammables around.• Under consumption of gas condition, close the valve
of cylinder and check the indicator if it is red and automatically being supplied gas from reserved cylinder.
• Check all pressure rate below while operation of regulator.
The Guideline of the products
10
Installation1. Check inside of pipe if it is clean or corrosion. If there is
corrosion, the pipe should be replaced with new pipe.2. Check the arrow mark on regulator to match with correct
direction of gas fl ow.3. Apply pipe compound on connection side of regulator in
order to avoid leakage before install.4. After fi nish with connecting the regulator with pipes, check
the OPSO operation. If it operates correctly, make it back to normal position and open the gas valve slowly.
5. It is recommended to install fi lter in front of regulator.6. Check the flow meter if the inlet & outlet pressures are
normal. Also, make sure to check if there is leakage on pipe connection.
The left hand side diagrams are showing the positions that can be installed unrestrictedly upon customer’s request.
Using low quality LP-Gas• Improper Lp-gas using may produce oil sludge and plug into
a product, causes damaged on diaphragm in the regulator. • In winter, inside of regulator turns to solidify. This creates
a problem that is blocking the nozzle from the resource supplier
NOTE: periodic checks should be made to assure piping and product remains clean from the distillation.. Recommend opening gas valve to clean out depending on weather.
• Recommend opening gas valve to clean a product periodically moisture in the cylinder may cause of corrosion. Also it brings a critical damage by freezing during the winter, depends on the weather periodic inspection should be made, recommend inspect within once in a month during the summer since less uses, once in a week during the winter.)
Incase of water into regulatorCorrosion is caused by water, corrosive atmospheres of salt and industrial pollutants, chemicals, and roadway contaminants. High concentrations can attack the metal parts vigorously. No suitable metals are totally resistant to such corrosion.
Horizontal pipe connection
Parallel Connection of Cylinder For parallel connection of cylinder, use pigtail hose to connect the pipe and each cylinders. The connection size PT1B or larger connection size is recommended. It is recommended to use the same regulator’s outlet connection size otherwise it will cause hunting. Also, the length of pipe must be at least 6m in between the second stage 1st reduction regulator and 2nd reduction regulator. Caution : When replacing cylinders, pigtails hose must be replaced with new one
Caution• This regulator is dedicated for LP Gas application. If use for other gas application may cause its performance.• Do not modify intentionally.• Do not block vent or vent tube.• A proper protection is needed to avoid rain, snow, direct
sunrays.
Position 1
Position 4
Position 7
Position 2
Position 5
Position 9Position 8
Position 3
Position 6
Position 10Pigtail Hose
PT 1B or Pipe
PT 1B or �Lager
www.hwa-young.com
1110
Maintenance• When replacing cylinder, turn the changeover lever to the
other side to make the indicator clear and then close the valve to replace the cylinder.
• After replacing cylinder, check all the indication and open the valve. Make sure to check if there is leakage.
• Do not stack anything around installed area for safety.• Do not move the cylinder without disconnection of hose or
piping.
Initial Usage • Replace all the cylinder to full gas cylinder.• Open the valve at reserved cylinder to flow the gas into the
regulator and then open the valve at supply cylinder.• Turn the lever to 180 degrees and check the indicator if it is
not red.• Remember to follow the instruction above when initial
usage or replacing of cylinder.• Start consumption of gas and check if the gas flow is
normal and also close the valve at supply cylinder and check if the regulator’s operation is normal as well.
Initial Usage At the condition with full of pressure for both gas cylinders, one cylinder can be selected by rotating changeover lever. The direction that appointed by lever end is the supplying cylinder and another one is reserve side.
Supply of GasThe gas is being flow into 2nd stage first reduction regulator from the supply cylinder and the pressure is being gradually decreased in supply cylinder.
Running out of gas from supply cylinderWhen the gas is being ran out, the pressure inside of regulator decreases and the main spring pushes the diaphragm downward and then this diaphragm plate pushes the valve seat downward in order to make the supply of gas from the reserved side. At this time the indicator turns red and shows that the gas is being supplied from reserved side.
Replacing Reserved CylinderThe reserved cylinder must be replaced with new full cylinder in order to avoid stop supply of gas.
Running out of gas from Reserved Cylinder When the indicator turns to red, the user must turn the lever to the other side. Once the lever turned to the other side, the inlet pressure is recovered its pressure rate and the pressure is increased to make diaphragm goes up ward and then the indicator turns to clear. At this time, the gas is being supplied at normal condition.
Automatic changeover pressure regulator
Installation Operation
High
Low
Pres
sure
Prel
imin
ary
High
Low
Pres
sure
Wor
king
High
Low
Pres
sure
Prel
imin
ary
High
Low
Pres
sure
Wor
king
High
LowPr
essu
rePr
elim
inar
y
High
Low
Pres
sure
Wor
king
High
Low
Pres
sure
Prel
imin
ary
High
Low
Pres
sure
Wor
king
High
Low
Pres
sure
Prel
imin
ary
High
Low
Pres
sure
Wor
king
1 2
3 4
5
화기엄금
Within 30cm
Within 30cm
Lighter than the air
Heavier than the air
Gas Leakage Shut offAdjustment
Control Panel
Gas MeterPigtail hose
ValveBlock
Changlover
The Guideline of the products
12
Leakage Test Dangerous
During Rainy SeasonEspecially during the rainy season, the gas is difficult to be ventilated in the atmosphere and easily being stayed underneath by the ground which is very dangerous. If the place possibly can be fl ooded, close all the gas valve including gas meter valve and evacuate.
Flooding AccidentAny places where had been fl ooded and recovery should be made, the gas specialist should carry out all testing and check for the area if there are any leakage of gas. Especially for the LP gas line, there might be lost cylinders or fl ooded cylinders, so the gas specialist should be checked if it is safe for use the gas appliances again. Before use the gas appliances, all the mud or foreign material should be wiped out or dried completely. Any fl ooded gas cylinders or pipes has potential explosion, so do not use any gas appliances prior to test or checked by gas specialist prior to use.
Keep away from the Flame. The flame causes hose damage and might cause explosion.
Replace the hose if there is crack or color fade.
Check if there are cracks or nicks.
Y
Too Short
Too Long
Bend
Twist
Replace the hose if the hose were exposed to high temperature or oily condition for long time.
Replace the hose if there are bites on hose by dogs or rats.
If the hose is bent or twisted for long time, the durability of hose might be affected and shortened the life time.
Do not place the hose by the corridor or underneath the chair.
The leakage might be caused if use Y connection or T connection.
Intentional disconnection or cut of hose is not allowed. It might cause leakage and explosion.
Do not place the hose behind the refrigerator or place where that can not visualize the hose easily because the hose should visually checked periodically.
If the hose is too long, it might affect to the outlet pressure and cause unexpected cracks.
Keep away from the heat
If the hose is too short, it might cause the leakage between the connections of valve and gas appliances.
1. BubbleUsing brush with soap water and gently apply soap water to hose connection including all connections of combustor area and observe for 2 minutes. If there is bubble around the connections, it means there is leakage, so the gas cylinder valve should be closed and call the gas technician or specialist. Bubble testing should be carried out once a month.
2. Visual Checking* It is required to visually check for the hose installation which made outside periodically. It is high potential to be occurred cracks or nicks by direct sunrays or animal bites. Once it has cracks or nicks, the hose should be replaced.
Visual Checking Area
Crack Bursting
GAS HOSE Guideline
Caution
www.hwa-young.com
1312
HYR SINGLE STAGE REGULATOR
HYR 1ST STAGE LOW AND MIDDLE LOW PRESSURE REGULATOR
ApplicationHwa Young’s single system regulator is optimized for single system of LP gas system. Generally, it can be used with connecting directly to the low capacity gas cylinder and provide reduced pressure properly. The application is for cooking at residence and low capacity heating and outdoor appliances with convenient at all time.Hwa Young’s single system regulator is designed for satisfied with quick response and proper pressure to supply of gas. The regulator works with inlet pressure (0.07MPa ~ 1.56MPa) and outlet pressure range(2.3~33kPa). If the pressure is excessive than the setting pressure, the equipped internal relief valve operates to maintain the pressure for safety.
The compact design of Single stage regulator’s makes convenient connection with gas cylinder. The outlet connection can be selected either hose or PT type which enable to connect with hose or pipe. Also the internal relief valve is equipped in low pressure type for the safety.
Feature - The loose stopper can avoid intentional opening. - The diaphragm which is certified for KS with its material NBR
can precisely measure the pressure to high accuracy of supply of setting flow rate of gas and it is possible for long lasting use.
- Internal relief is equipped for safety by release of the gas to the atmosphere to prevent explosion. (Low Pressure)
- The aluminum die casting body makes very neat exterior by precise machining. The corrosion resistance body makes possible for semi permanently use.
- The direct operation system and optimized design for gas flow enable quick response to variation of gas flow.
Single Stage Regulator
14
Installation 1. Check if the gas regulator and the cylinder’s specifi cation is correctly matched. 2. Refer to Fig. 1 and connect the cylinder and regulator by tightening handle. 3. Check if the connection end of pipe is clean and apply Tefl on piping tape or
sealant for connection like Fig. 2-1.3. Connect the pigtail hose with regulator with referring to Fig. 2-2 and use
handle for tightening. Fig 1. Cylinder Fig 2-2. Hose Conn.Fig 2-1. Pipe Conn.
Inlet Pressure Range (P1) : 0.07~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPaOutlet pressure Range : 2.8±0.5 kPaCapacity : 4 kg/hInternal Relief Working Pressure : 7.0±1.4 kPaInlet Connection Size : Pol Handle L.H W22.5*14TOutlet Connection Size : Hose endApplication : Household
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPaOutlet pressure Range : 2.8±0.5 kPaCapacity : 20 kg/hInternal Relief Working Pressure : 7.0±1.4 kPaInlet Connection Size : PT 1/2BOutlet Connection Size : PT 1BApplication : Household & Commercial
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPaOutlet pressure Range : 2.8±0.5 kPaCapacity : 35 kg/hInternal Relief Working Pressure : 7.0±1.4 kPaInlet Connection Size : PT 1/2BOutlet Connection Size : PT 1BApplication : Household & Commercial
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPaOutlet pressure Range : 2.8±0.5 kPaCapacity : 12 kg/hInternal Relief Working Pressure : 7.0±1.4 kPaInlet Connection Size : PT 1/2BOutlet Connection Size : PT 3/4BApplication : Household & Commercial
Inlet Pressure Range (P1) : 0.07~1.56 MPa 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPa 6, 10, 15, 20, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 5kg/h 5 kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : Pol Handle L.H W22.5*14T Pol Handle L.H W22.5*14TOutlet Connection Size : PT 1/2B PT 1/2BApplication : Household & Commercial Household & Commercial
Inlet Pressure Range (P1) : 0.07~1.56 MPa 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPa 6, 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 7 kg/h 7 kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : Pol Handle L.H W22.5*14T Pol Handle L.H W22.5*14TOutlet Connection Size : PT 1/2B PT 1/2BApplication : Household & Commercial Household & Commercial
www.hwa-young.com
RQ4 P MPa570 0. 1- . 6
KPa2: .8
MADE IN KOREA
L.P.G
L.P.GMADE IN KOREA
MADE IN KOREA 60
040816
HYR4 HYR5 HYR7 HYR12, 20, 35
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
54.5
65
Ø89
167
60
79
162.5
Ø89
050402
75 93
170
Ø105Ø140
188
128108
RQ4 P MPa570 0. 1- . 6
KPa2: .8
MADE IN KOREA
L.P.G
L.P.GMADE IN KOREA
MADE IN KOREA 60
040816
HYR4 HYR5 HYR7 HYR12, 20, 35
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
54.5
65
Ø89
167
60
79
162.5
Ø89
050402
75 93
170
Ø105Ø140
188
128108
RQ4 P MPa570 0. 1- . 6
KPa2: .8
MADE IN KOREA
L.P.G
L.P.GMADE IN KOREA
MADE IN KOREA 60
040816
HYR4 HYR5 HYR7 HYR12, 20, 35
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
54.5
65
Ø89
167
60
79
162.5
Ø89
050402
75 93
170
Ø105Ø140
188
128108
RQ4 P MPa570 0. 1- . 6
KPa2: .8
MADE IN KOREA
L.P.G
L.P.GMADE IN KOREA
MADE IN KOREA 60
040816
HYR4 HYR5 HYR7 HYR12, 20, 35
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
54.5
65
Ø89
167
60
79
162.5
Ø89
050402
75 93
170
Ø105Ø140
188
128108
RQ4 P MPa570 0. 1- . 6
KPa2: .8
MADE IN KOREA
L.P.G
L.P.GMADE IN KOREA
MADE IN KOREA 60
040816
HYR4 HYR5 HYR7 HYR12, 20, 35
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
54.5
65
Ø89
167
60
79
162.5
Ø89
050402
75 93
170
Ø105Ø140
188
128108
RQ4 P MPa570 0. 1- . 6
KPa2: .8
MADE IN KOREA
L.P.G
L.P.GMADE IN KOREA
MADE IN KOREA 60
040816
HYR4 HYR5 HYR7 HYR12, 20, 35
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
54.5
65
Ø89
167
60
79
162.5
Ø89
050402
75 93
170
Ø105Ø140
188
128108
HYR-4
HYR-20 HYR-35
HYR-5
HYR-7 HYR-12
Low Pressure Type
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Low Pressure Type
Low Pressure Type
1514
HYRM SERIES REGULATOR
HYRM SERIES 1ST STAGE MIDDLE PRESSURE REGULATOR (NON ADJUSTABLE TYPE) HYRM SERIES regulator is for the second stage first reduction system that reduces range 0.1~15.6 MPa to 0.057~0.083 MPa.
IntroduceThe HYRM Series (Non adjustable) is for first stage reduction side under twice pressure reduction system. The inlet pressure which it can handle is 14.2~221.52 Psi (0.1~1.56MPa) and reduce to 8.1~11.8 Psi (0.057~0.083 MPa). Our regulator of second stage twice reduction is necessary to be connected after HYRM series for properly use of gas at useful pressure. Also, it can be used in industrial and commercial application. HYRM series is easy to reinstall with adjusting pressure setting by equipped bolt. The compact design makes easy to install in small space.For easy installation, the PT thread is selected. The valve seat is equipped by inlet side to control fast and precisely for variation of inlet pressure, so the safety and high performance is guaranteed.
Feature High accuracy and fast response at max flow of gas is one of strong point and it has high strength to avoid corrosion as well as excellent durability.
*Possible to forward precise load by fabric diaphragm inside of regulator and continue to use for long time as it has low chance for deformation and damage of diaphragm.
*It is designed to minimize the freezing inside by selecting larger diameter of orifice. Easy to reinstall with adjusting pressure setting by equipped bolt. The compact design makes easy to install in small space.
1st Stage Regulator
16
59
42
INLET OUTLET19
4
106
38
CAP
COVER
BODY 222
134
28
93
CAP
COVER
BODYINLET OUTLET
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.057~0.083 MPaCapacity : 35 kg/hLock Up Pressure : 0.095 MPaInlet Connection Size : PT 3/4Outlet Connection Size : PT 3/4Application : Industrial
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.057~0.083 MPaCapacity : 100 kg/hLock Up Pressure : 0.095 MPaInlet Connection Size : PT 1BOutlet Connection Size : PT 1BApplication : Industrial
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.057~0.083 MPaCapacity : 300 kg/hLock Up Pressure : 0.095 MPaInlet Connection Size : PT 1-1/2BOutlet Connection Size : PT 1-1/2BApplication : Industrial
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.057~0.083 MPaCapacity : 400 kg/hLock Up Pressure : 0.095 MPaInlet Connection Size : PT 2BOutlet Connection Size : PT 2BApplication : Industrial
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.057~0.083 MPaCapacity : 60 kg/hLock Up Pressure : 0.095 MPaInlet Connection Size : PT 3/4Outlet Connection Size : PT 3/4Application : Industrial
Inlet Pressure Range (P1) : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.057~0.083 MPaCapacity : 200 kg/hLock Up Pressure : 0.095 MPaInlet Connection Size : PT 1-1/2BOutlet Connection Size : PT 1-1/2BApplication : Industrial
HYRM SERIES When it is used as first stage for 2ND reduction system, it should be checked if the inlet pressure is matched with regulator’s specifi cation. At the condition with full of pressure for both gas cylinder, one cylinder can be selected by rotating changeover lever. The direction that appointed by lever end is the supplying cylinder and another one is reserve side.
1.00.6
0.4
0.2
0.8
1.61.21.4
1.6
0.2
0.6
0.4
0.8 1.0
1.4
1.2
supply partreserve part
Right suppling Left suppling
supply part
adjusting handle
Pressure:0.057~0.083 MPa Pressure:0.057~0.083 MPaPressure:0.032~0.057MPa Pressure:0.032~0.057MPa
reserve part
HYRM-35
HYRM-100
HYRM-300
HYRM-60
HYRM-200
HYRM-400
www.hwa-young.com
INO
UT
INO
UT
INO
UT
9924
0
234
53
108
76
240
240
129
77
76
240
130
77
240
INO
UT
INO
UT
INO
UT
9924
0
234
53
108
76
240
240
129
77
76
240
130
77
240
INO
UT
INO
UT
INO
UT
9924
0
234
53
108
76
240
240
129
77
76
240
130
77
240
INO
UT
INO
UT
INO
UT
9924
0
234
53
108
76
240
240
129
77
76
240
130
77
240
1716
HYRM SERIES REGULATOR
HYRM SERIES 1ST STAGE MIDDLE PRESSURE REGULATOR (ADJUSTABLE TYPE) HYRM SERIES regulator is for the second stage first reduction system that reduces range 0.2~15.6 MPa to 0.1~0.2 MPa.
IntroduceThe HYRM Series (adjustable) is for first stage reduction side under twice pressure reduction system. The inlet pressure which it can handle is 0.02~0.1.56MPa and reduce to 0.1~0.2MPa. Our regulator of second stage twice reduction is necessary to be connected after HYRM series for properly use of gas at useful pressure. Also, it can be used in industrial and commercial application. The HYRM adjustable regulator is easy to adjust the pressure by simply adjusting the handle on top of regulator when install or maintenance. Also, its compact design enables to install in limited space.The connection type PT thread makes easy connection to pipe. It is guaranteed for safety and high performance from controlling precisely response to variation of inlet pressure by valve seat which equipped at inlet side.
Feature High accuracy and fast response at max flow of gas is one of strong point and it has high strength to avoid corrosion as well as excellent durability. And also, easy to reinstall with adjusting pressure setting by equipped handle.
Easy to Maintain With two bolt connection type with body and diaphragm, it is easy to maintain without disassembly of pipe line. Practical use of SpaceUnrestrictedly install with changing position of regulator according to construction condition.Outlet pressure adjustmentIt is possible with readjusting outlet pressure by replacing spring.Corrosion resistance materials Corrosion resistance materials are used for long lasting use of regulator under bad weather condition.
1st Stage Regulator
18
0
2
0.3
kgf/cmMPa
3
1.5
0.15
0.5 0.05
1
0.1
0.25
2.5
2
0.2
0
2
0.3
kgf/cmMPa
3
1.5
0.150.5 0.05
10.1
0.25
2.5
2
0.2
Outlet Pressure SettingHYRM adjustable regulator’s outlet pressure setting can be adjusted by handle that are equipped on the top of the regulator.The outlet pressure setting can be adjusted referring to following diagram.
Adjusting MethodHYRM adjustable regulator’s outlet pressure setting can be adjusted to 0~0.27 (Max) Bar. The standard outlet pressure setting is 0.15Bar.
Check if the pressure gauge is indicating “0”. After checking for desired pressure rate through pressure gauge and open the valve at inlet side for supplying of gas. After checking for standard setting pressure through pressure gauge and adjust the pressure by rotating handle on top of regulator. When Setting Pressure IncreasesRotate the handle on top of regulator as diagram above with checking pressure gauge, and see if the setting pressure increases. After setting of desired pressure rate, observe pressure gauge for 1 ~ 2 minutes. Make sure to specify the adjusted setting pressure on name plate of regulator. When Setting Pressure DecreasesRotate the handle on top of regulator as diagram above with checking pressure gauge, and see if the setting pressure decreases After setting of desired pressure rate, observe pressure gauge for 1 ~ 2 minutes. Make sure to specify the adjusted setting pressure on name plate of regulator.
CautionWhen adjusting outlet pressure setting, the outlet pressure must be in the range of 2nd reduction regulator’s inlet pressure.If the setting outlet pressure is higher than the range of 2nd reduction regulator or combustor, it might cause damage.
When Setting Pressure Decreases
When Setting Pressure Increases
www.hwa-young.com
0
2
0.3
kgf/cmMPa
3
1.5
0.15
0.5
0.051
0.1
0.25
2.5
2
0.2
INLET PRESSUREOUTLET PRESSUREATMOSPHERE PRESSURE
ADJUSTING SCREW
CONTROL SPRING
DIAPHRAGM ASSEMBLY
CONTROL HANDLE
GAUGE PRESSURE
1918
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPaO
utle
t Pre
ssur
e (M
Pa)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 200.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
18040 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
40 60 80 100 120 140 0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
100Capacity (kg/h-LPG)
40 60 80Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
10 30 50 70 90
0 500.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
300
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
180Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
100 150 200 25025 75 125 175 225 275
40 60 80 100 120 140 160 180 200 220 240 260 40 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 600.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
500
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
300Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
130 190 300 40030 100 160 250 350 450
40 60 100 130 160 190 210 240 270 300 350 400 40 60 80 100 150 200 250
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
HYRM-B350 가변형 조정기HYRM-15 공기조정기
0 1
Set Pressure: 0.15 MPa
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.3 MPaInlet Pressure: 0.35 MPa Inlet Pressure: 1.56 MPa
0.05
0.1
0.15
0.2
0.25
3 5 10 15 20 40Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
0 10.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
602 4 6 8 10 15 25
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.35 MPaInlet Pressure: 0.4 MPa Inlet Pressure: 1.56 MPa
0.3
0 2
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.2 MPa Inlet Pressure: 0.25 MPaInlet Pressure: 0.3 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
30Capacity (kg/h-LPG)
6 8 121 4 7 10 15
HYRM 10 유량표 HYRM 35 유량표
HYRM 60 유량표HYRM 15 유량표
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 200.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
18040 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
40 60 80 100 120 140 0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
100Capacity (kg/h-LPG)
40 60 80Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
10 30 50 70 90
0 500.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
300
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
180Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
100 150 200 25025 75 125 175 225 275
40 60 80 100 120 140 160 180 200 220 240 260 40 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 600.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
500
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPaO
utle
t Pre
ssur
e (M
Pa)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
300Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
130 190 300 40030 100 160 250 350 450
40 60 100 130 160 190 210 240 270 300 350 400 40 60 80 100 150 200 250
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
HYRM-B350 가변형 조정기HYRM-15 공기조정기
0 1
Set Pressure: 0.15 MPa
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.3 MPaInlet Pressure: 0.35 MPa Inlet Pressure: 1.56 MPa
0.05
0.1
0.15
0.2
0.25
3 5 10 15 20 40Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
0 10.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
602 4 6 8 10 15 25
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.35 MPaInlet Pressure: 0.4 MPa Inlet Pressure: 1.56 MPa
0.3
0 2
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.2 MPa Inlet Pressure: 0.25 MPaInlet Pressure: 0.3 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
30Capacity (kg/h-LPG)
6 8 121 4 7 10 15
HYRM 10 유량표 HYRM 35 유량표
HYRM 60 유량표HYRM 15 유량표
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 200.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
18040 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
40 60 80 100 120 140 0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
100Capacity (kg/h-LPG)
40 60 80Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
10 30 50 70 90
0 500.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
300
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
180Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
100 150 200 25025 75 125 175 225 275
40 60 80 100 120 140 160 180 200 220 240 260 40 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 600.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
500
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPaO
utle
t Pre
ssur
e (M
Pa)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
300Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
130 190 300 40030 100 160 250 350 450
40 60 100 130 160 190 210 240 270 300 350 400 40 60 80 100 150 200 250
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
HYRM-B350 가변형 조정기HYRM-15 공기조정기
0 1
Set Pressure: 0.15 MPa
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.3 MPaInlet Pressure: 0.35 MPa Inlet Pressure: 1.56 MPa
0.05
0.1
0.15
0.2
0.25
3 5 10 15 20 40Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
0 10.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
602 4 6 8 10 15 25
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.35 MPaInlet Pressure: 0.4 MPa Inlet Pressure: 1.56 MPa
0.3
0 2
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.2 MPa Inlet Pressure: 0.25 MPaInlet Pressure: 0.3 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
30Capacity (kg/h-LPG)
6 8 121 4 7 10 15
HYRM 10 유량표 HYRM 35 유량표
HYRM 60 유량표HYRM 15 유량표
Inlet Pressure Range : Max 1.56 MPa
Outlet Pressure Range : 0 ~ 0.2 MPa
Capacity : Max 15 kg/h
Inlet Connection Size : Pol Handle, LH W22.5x14T
Outlet Connection Size : PT 1/2B
Application : Industrial
Inlet Pressure Range : Max 1.56 MPa
Outlet Pressure Range : 0 ~ 0.2 MPa
Capacity : Max 15 kg/h
Inlet Connection Size : Pol Handle, LH W22.5x14T
Outlet Connection Size : Hose end
Application : Industrial
Inlet Pressure Range : Max 1.56 MPa
Outlet Pressure Range : 0 ~ 0.3 MPa
Capacity : Max 20 kg/h
Inlet Connection Size : NPT 1/4"
Outlet Connection Size : NPT 1/4"
Application : Industrial
Service P1 (MPa) P2 (MPa) Capacity
LPG
0.25~1.56 0.1 9 kg/h
0.3~1.56 0.15 10 kg/h
0.4~1.56 0.2 15 kg/h
Service P1 (MPa) P2 (MPa) Capacity
LPG
0.25~1.56 0.1 9 kg/h
0.3~1.56 0.15 10 kg/h
0.4~1.56 0.2 15 kg/h
Service P1 (MPa) P2 (MPa) Capacity
LPG
0.25~1.56 0.1 10 kg/h
0.3~1.56 0.15 15 kg/h
0.4~1.56 0.3 20 kg/h
1st Stage Regulator
HYRM SERIES REGULATOR
주의: 기존용도
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-10
250 PSILP-GAS REGULATOR MAXIMUM INLET PRESSURE18SY
FOR OUTDOOR USE.INSTALL UNDER A PROTECTIVECOVER OR WITH VENT OPENINGVERTICALLY DOWN.
OUTLET PRESSURE SETTINGCONNECTION
SPRING RANGE 0~35 PSI28 PSI
1/4" FNPTMADE INKOREA
LISTED CAPACITYMODEL
700,000 Btu/hrHYRM-15
172
105
L.H W22.5x14T
Ø60
HWA
LP-G
HWA YOUNG CO.
LP-GAS REGULATOR
5533.5
60
Ø11
(HO
SE E
ND
)10
5
140
60
Ø33.5
Ø60
50
Ø73
WARNING:
HWA YOUNG CO.
LP-GAS REGULATOR
60.2
28.7
104
65
27
HWA YOUNG CO.
LP-GAS REGULATOR
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-5
HWA
LP-G
용 도
Lot.No :
출 구 압 력
최대입구압력
용 량
모 델
134
190
200
190
116
223.
523
4
223.
5
41.5
37.7
10659.2
180
PT 3/4PT 3/4
PT 3/4PT 3/4
IN OUT
B35 가변조정기
B60 가변조정기B10A 가변조정기
B15 가변조정기
B10 가변조정기
주의: 기존용도
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-10
250 PSILP-GAS REGULATOR MAXIMUM INLET PRESSURE18SY
FOR OUTDOOR USE.INSTALL UNDER A PROTECTIVECOVER OR WITH VENT OPENINGVERTICALLY DOWN.
OUTLET PRESSURE SETTINGCONNECTION
SPRING RANGE 0~35 PSI28 PSI
1/4" FNPTMADE INKOREA
LISTED CAPACITYMODEL
700,000 Btu/hrHYRM-15
172
105
L.H W22.5x14T
Ø60
HWA
LP-G
HWA YOUNG CO.
LP-GAS REGULATOR
5533.5
60
Ø11
(HO
SE E
ND
)10
5
140
60
Ø33.5
Ø60
50
Ø73
WARNING:
HWA YOUNG CO.
LP-GAS REGULATOR
60.2
28.7
104
65
27
HWA YOUNG CO.
LP-GAS REGULATOR
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-5
HWA
LP-G
용 도
Lot.No :
출 구 압 력
최대입구압력
용 량
모 델
134
190
200
190
116
223.
523
4
223.
5
41.5
37.7
10659.2
180
PT 3/4PT 3/4
PT 3/4PT 3/4
IN OUT
B35 가변조정기
B60 가변조정기B10A 가변조정기
B15 가변조정기
B10 가변조정기
주의: 기존용도
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-10
250 PSILP-GAS REGULATOR MAXIMUM INLET PRESSURE18SY
FOR OUTDOOR USE.INSTALL UNDER A PROTECTIVECOVER OR WITH VENT OPENINGVERTICALLY DOWN.
OUTLET PRESSURE SETTINGCONNECTION
SPRING RANGE 0~35 PSI28 PSI
1/4" FNPTMADE INKOREA
LISTED CAPACITYMODEL
700,000 Btu/hrHYRM-15
172
105
L.H W22.5x14T
Ø60
HWA
LP-G
HWA YOUNG CO.
LP-GAS REGULATOR
5533.5
60
Ø11
(HO
SE E
ND
)10
5
140
60
Ø33.5
Ø60
50
Ø73
WARNING:
HWA YOUNG CO.
LP-GAS REGULATOR
60.2
28.7
104
65
27
HWA YOUNG CO.
LP-GAS REGULATOR
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-5
HWA
LP-G
용 도
Lot.No :
출 구 압 력
최대입구압력
용 량
모 델
134
190
200
190
116
223.
523
4
223.
5
41.5
37.7
10659.2
180
PT 3/4PT 3/4
PT 3/4PT 3/4
IN OUT
B35 가변조정기
B60 가변조정기B10A 가변조정기
B15 가변조정기
B10 가변조정기
HYRM-10
HYRM-10A
HYRM-15
Capacity Rate Information
Capacity Rate Information
Capacity Rate Information
20
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 200.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
18040 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
40 60 80 100 120 140 0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
100Capacity (kg/h-LPG)
40 60 80Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)10 30 50 70 90
0 500.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
300
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
180Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
100 150 200 25025 75 125 175 225 275
40 60 80 100 120 140 160 180 200 220 240 260 40 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 600.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
500
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
300Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
130 190 300 40030 100 160 250 350 450
40 60 100 130 160 190 210 240 270 300 350 400 40 60 80 100 150 200 250
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
HYRM-B350 가변형 조정기HYRM-15 공기조정기
0 1
Set Pressure: 0.15 MPa
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.3 MPaInlet Pressure: 0.35 MPa Inlet Pressure: 1.56 MPa
0.05
0.1
0.15
0.2
0.25
3 5 10 15 20 40Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
0 10.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
602 4 6 8 10 15 25
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.35 MPaInlet Pressure: 0.4 MPa Inlet Pressure: 1.56 MPa
0.3
0 2
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.2 MPa Inlet Pressure: 0.25 MPaInlet Pressure: 0.3 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
30Capacity (kg/h-LPG)
6 8 121 4 7 10 15
HYRM 10 유량표 HYRM 35 유량표
HYRM 60 유량표HYRM 15 유량표
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 200.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
18040 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
40 60 80 100 120 140 0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
100Capacity (kg/h-LPG)
40 60 80Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)10 30 50 70 90
0 500.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
300
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
180Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
100 150 200 25025 75 125 175 225 275
40 60 80 100 120 140 160 180 200 220 240 260 40 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 600.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
500
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
300Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
130 190 300 40030 100 160 250 350 450
40 60 100 130 160 190 210 240 270 300 350 400 40 60 80 100 150 200 250
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
HYRM-B350 가변형 조정기HYRM-15 공기조정기
0 1
Set Pressure: 0.15 MPa
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.3 MPaInlet Pressure: 0.35 MPa Inlet Pressure: 1.56 MPa
0.05
0.1
0.15
0.2
0.25
3 5 10 15 20 40Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
0 10.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
602 4 6 8 10 15 25
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.35 MPaInlet Pressure: 0.4 MPa Inlet Pressure: 1.56 MPa
0.3
0 2
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.2 MPa Inlet Pressure: 0.25 MPaInlet Pressure: 0.3 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
30Capacity (kg/h-LPG)
6 8 121 4 7 10 15
HYRM 10 유량표 HYRM 35 유량표
HYRM 60 유량표HYRM 15 유량표
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 50.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 10
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
65
5 10 15 20 25 30155 20 25 30 35 40 45 50 55
10 15 20 25 30 35 40 45 50 55 60
0 200.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
18040 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
40 60 80 100 120 140 0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
100Capacity (kg/h-LPG)
40 60 80Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
10 30 50 70 90
0 500.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPaO
utle
t Pre
ssur
e (M
Pa)
300
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
180Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
100 150 200 25025 75 125 175 225 275
40 60 80 100 120 140 160 180 200 220 240 260 40 60 80 100 120 140 160
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0 600.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
500
0 20
Set Pressure: 0.15 MPa
Inlet Pressure: 0.35 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0.3
0.05
0.1
0.15
0.2
0.25
0 20
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
300Capacity (kg/h-LPG)Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
130 190 300 40030 100 160 250 350 450
40 60 100 130 160 190 210 240 270 300 350 400 40 60 80 100 150 200 250
Inlet Pressure: 0.4 MPa Inlet Pressure: 0.6 MPaInlet Pressure: 1.0 MPa Inlet Pressure: 1.56 MPa
HYRM-B350 가변형 조정기HYRM-15 공기조정기
0 1
Set Pressure: 0.15 MPa
Inlet Pressure: 0.25 MPa Inlet Pressure: 0.3 MPaInlet Pressure: 0.35 MPa Inlet Pressure: 1.56 MPa
0.05
0.1
0.15
0.2
0.25
3 5 10 15 20 40Capacity (kg/h-LPG)
Out
let P
ress
ure
(MPa
)
0 10.1
0.15
0.2
0.25
Capacity (kg/h-LPG)
Set Pressure: 0.2 MPa
Out
let P
ress
ure
(MPa
)
602 4 6 8 10 15 25
Inlet Pressure: 0.3 MPa Inlet Pressure: 0.35 MPaInlet Pressure: 0.4 MPa Inlet Pressure: 1.56 MPa
0.3
0 2
Set Pressure: 0.1 MPa
Out
let P
ress
ure
(MPa
)
Inlet Pressure: 0.2 MPa Inlet Pressure: 0.25 MPaInlet Pressure: 0.3 MPa Inlet Pressure: 1.56 MPa
0
0.05
0.1
0.15
0.2
30Capacity (kg/h-LPG)
6 8 121 4 7 10 15
HYRM 10 유량표 HYRM 35 유량표
HYRM 60 유량표HYRM 15 유량표
Inlet Pressure Range : Max 1.56 MPa
Outlet Setting Pressure (P2) : 0.16 ~ 0.24 MPa
Outlet Pressure Range : 0 ~ 0.2 MPa
Capacity : Max 150 kg/h
Working Temperature : -20 °C ~ 60 °C
Connection Size : PT 3/4
Inlet Pressure Range : Max 1.56 MPa
Outlet Setting Pressure (P2) : 0.16 ~ 0.24 MPa
Outlet Pressure Range : 0 ~ 0.2 MPa
Capacity : Max 220 kg/h
Working Temperature : -20 °C ~ 60 °C
Connection Size : PT 3/4
Inlet Pressure Range : Max 1.56 MPa
Outlet Setting Pressure (P2) : 0.08 ~ 0.24 MPa
Outlet Pressure Range : 0 ~ 0.2 MPa
Capacity : Max 350 kg/h
Working Temperature : -20 °C ~ 60 °C
Connection Size : PT 1-1/4“
Service P1 (MPa) P2 (MPa) Capacity
LPG
0.25~1.56 0.1 80 kg/h
0.3~1.56 0.15 100 kg/h
0.4~1.56 0.2 150 kg/h
Service P1 (MPa) P2 (MPa) Capacity
LPG
0.25~1.56 0.1 150 kg/h
0.35~1.56 0.15 200 kg/h
0.4~1.56 0.2 220 kg/h
Service P1 (MPa) P2 (MPa) Capacity
LPG
0.25~1.56 0.1 150 kg/h
0.3~1.56 0.15 220 kg/h
0.4~1.56 0.2 350 kg/h
www.hwa-young.com
주의: 기존용도
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-10
250 PSILP-GAS REGULATOR MAXIMUM INLET PRESSURE18SY
FOR OUTDOOR USE.INSTALL UNDER A PROTECTIVECOVER OR WITH VENT OPENINGVERTICALLY DOWN.
OUTLET PRESSURE SETTINGCONNECTION
SPRING RANGE 0~35 PSI28 PSI
1/4" FNPTMADE INKOREA
LISTED CAPACITYMODEL
700,000 Btu/hrHYRM-15
172
105
L.H W22.5x14T
Ø60
HWA
LP-G
HWA YOUNG CO.
LP-GAS REGULATOR
5533.5
60
Ø11
(HO
SE E
ND
)10
5
140
60
Ø33.5
Ø60
50
Ø73
WARNING:
HWA YOUNG CO.
LP-GAS REGULATOR
60.2
28.7
104
65
27
HWA YOUNG CO.
LP-GAS REGULATOR
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-5
HWA
LP-G
용 도
Lot.No :
출 구 압 력
최대입구압력
용 량
모 델
134
190
200
190
116
223.
523
4
223.
5
41.5
37.7
10659.2
180
PT 3/4PT 3/4
PT 3/4PT 3/4
IN OUT
B35 가변조정기
B60 가변조정기B10A 가변조정기
B15 가변조정기
B10 가변조정기
주의: 기존용도
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-10
250 PSILP-GAS REGULATOR MAXIMUM INLET PRESSURE18SY
FOR OUTDOOR USE.INSTALL UNDER A PROTECTIVECOVER OR WITH VENT OPENINGVERTICALLY DOWN.
OUTLET PRESSURE SETTINGCONNECTION
SPRING RANGE 0~35 PSI28 PSI
1/4" FNPTMADE INKOREA
LISTED CAPACITYMODEL
700,000 Btu/hrHYRM-15
172
105
L.H W22.5x14T
Ø60
HWA
LP-G
HWA YOUNG CO.
LP-GAS REGULATOR
5533.5
60
Ø11
(HO
SE E
ND
)10
5
140
60
Ø33.5
Ø60
50
Ø73
WARNING:
HWA YOUNG CO.
LP-GAS REGULATOR
60.2
28.7
104
65
27
HWA YOUNG CO.
LP-GAS REGULATOR
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-5
HWA
LP-G
용 도
Lot.No :
출 구 압 력
최대입구압력
용 량
모 델
134
190
200
190
116
223.
523
4
223.
5
41.5
37.7
10659.2
180
PT 3/4PT 3/4
PT 3/4PT 3/4
IN OUT
B35 가변조정기
B60 가변조정기B10A 가변조정기
B15 가변조정기
B10 가변조정기
주의: 기존용도
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-10
250 PSILP-GAS REGULATOR MAXIMUM INLET PRESSURE18SY
FOR OUTDOOR USE.INSTALL UNDER A PROTECTIVECOVER OR WITH VENT OPENINGVERTICALLY DOWN.
OUTLET PRESSURE SETTINGCONNECTION
SPRING RANGE 0~35 PSI28 PSI
1/4" FNPTMADE INKOREA
LISTED CAPACITYMODEL
700,000 Btu/hrHYRM-15
172
105
L.H W22.5x14T
Ø60
HWA
LP-G
HWA YOUNG CO.
LP-GAS REGULATOR
5533.5
60
Ø11
(HO
SE E
ND
)10
5
140
60
Ø33.5
Ø60
50
Ø73
WARNING:
HWA YOUNG CO.
LP-GAS REGULATOR
60.2
28.7
104
65
27
HWA YOUNG CO.
LP-GAS REGULATOR
주의: 기존용도 외 다른 용도로 사용할 수 없습니다.
용 량
용 도
Lot.No :
최대입구압력
출 구 압 력
모 델
10 Kg/hr
MADE INKOREA
1.56 MPa0.15 MPa±20%
용접절단용, 공업용
HYRM-5
HWA
LP-G
용 도
Lot.No :
출 구 압 력
최대입구압력
용 량
모 델
134
190
200
190
116
223.
523
4
223.
5
41.5
37.7
10659.2
180
PT 3/4PT 3/4
PT 3/4PT 3/4
IN OUT
B35 가변조정기
B60 가변조정기B10A 가변조정기
B15 가변조정기
B10 가변조정기
HYRM-35A
HYRM-60A
HYRM-350A
Capacity Rate Information
Capacity Rate Information
Capacity Rate Information
2120
HYR SECOND STAGE REGULATOR
HYR SERIES 2ND STAGE LOW & MIDDLE PRESSURE REGULATOR This regulator is for the second stage first reduction system that reduces pressure range 0.001~0.4MPa to low pressure or middle low pressure. This reduced pressure range enable to use second reduction regulator in order to reduce the pressure for proper use of commercial or industrial application.
Parts and Operation Diagram FeaturesAnti corrosion parts are used for high durability. Also this regulator gives quick response to max flow rate.
A special diaphragm gives its best performance in reducing pressure precisely and is possible for long lasting use.
This regulator is specialized in gas supplying system for multiple dwellings and residential or office buildings.
An internal relief valve is equipped for safety.
CONTROL SPRING
RELIEF VALVE SPRING
VALVE STEM
VALVE SEAT
DIAPHRAGM ASSEMBLY
LOW PRESSURE FOR DIAPHRAGMS ASSEMBLY
INLET PRESSUREOUTLET PRESSUREATMOSPHERE PRESSURE
COVER
STRAINER
2nd Stage Regulator
22
Inlet Pressure Range : 0.01-0.15 MPa 0.025~0.15 MPaSetting Outlet Pressure (P2) : 2.8 kPa 6, 10, 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 5 kg/h 5 kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 1/2B or PT 3/4B PT 3/4BOutlet Connection Size : PT 1/2B or PT 3/4B PT 3/4BApplication : Household & Commercial Household & Commercial
Inlet Pressure Range : 0.01-0.15 MPa 0.025~0.15 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 12 kg/h 12 kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 1/2B PT 3/4BOutlet Connection Size : PT 3/4B PT 3/4BApplication : Commercial Commercial
Inlet Pressure Range : 0.01-0.15 MPa 0.025~0.15 MPaSetting Outlet Pressure (P2) : 2.8 kPa 6, 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 7 kg/h 7 kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 3/4B PT 3/4BOutlet Connection Size : PT 3/4B PT 3/4BApplication : Household & Commercial Household & Commercial
Inlet Pressure Range : 0.04~0.4 MPaSetting Outlet Pressure (P2) : 15, 25 kPaOutlet pressure Range : P2±Within 20%Capacity : 15 kg/hInternal Relief Working Pressure : No Relief Inlet Connection Size : PT 3/4BOutlet Connection Size : PT 3/4BApplication : Commercial
HYR-220
HYR-212
HYR-205
HYR-220C
HYR-215C
HYR-207
www.hwa-young.com
60
HYR-215C
60
Ø140
HYR-212
HYR-205, 207
HYR-220, 220C
L.P.G
MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
Ø14010
812
8188188
108
128
6180
146
Ø89
226
116.5
140
Ø180
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
60
HYR-215C
60
Ø140
HYR-212
HYR-205, 207
HYR-220, 220C
L.P.G
MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
Ø14010
812
8
188188
108
128
6180
146
Ø89
226
116.5
140
Ø180
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
60
HYR-215C
60
Ø140
HYR-212
HYR-205, 207
HYR-220, 220C
L.P.G
MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
Ø14010
812
8
188188
108
128
6180
146
Ø89
226
116.5
140
Ø180
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
60
HYR-215C
60
Ø140
HYR-212
HYR-205, 207
HYR-220, 220C
L.P.G
MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
Ø14010
812
8
188188
108
128
6180
146
Ø89
226
116.5
140
Ø180
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
60
HYR-215C
60
Ø140
HYR-212
HYR-205, 207
HYR-220, 220C
L.P.G
MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
Ø14010
812
8
188188
108
128
6180
146
Ø89
226
116.5
140
Ø180
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
60
HYR-215C
60
Ø140
HYR-212
HYR-205, 207
HYR-220, 220C
L.P.G
MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
Ø14010
812
8
188188
108
128
6180
146
Ø89226
116.5
140
Ø180
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
HWA YOUNG CO.MADE IN KOREA
L.P.GREGULATOR
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type
Inlet Pressure Range : 0.01~0.15 MPa 0.025~0.15 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 20 kg/h 20 kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 3/4B PT 3/4BOutlet Connection Size : PT 1B PT 1BApplication : Commercial & Industrial Commercial & Industrial
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type
Middle Low Pressure Type
Inlet Pressure Range : 0.04~0.4 MPaSetting Outlet Pressure (P2) : 15, 25 kPaOutlet pressure Range : P2±Within 20%Capacity : 20 kg/hInternal Relief Working Pressure : No Relief Inlet Connection Size : PT 3/4BOutlet Connection Size : PT 1BApplication : Commercial & Industrial
Middle Low Pressure Type
2322
Advantages for Second Stage Reduction SystemAllowances for Adding AppliancesAppliances can be added later to the existing load provided the high pressure regulator can handle the increase by the addition of second low pressure regulator. Since appliances can be regulated independently, demands from other parts of the installation won’t affect their individual performances.
High CapacityThe second stage reduction system can cover higher capacity of gas than single stage reduction system.
Minimizes Freeze UpThe regulator freeze ups occurs when moisture in the gas condenses and freezes on cold surfaces of the regulator nozzles. The nozzle becomes chilled when high pressure gas expands across it into the regulator body This chilling action is more severe in single stage system. However, the second stage reduction system can greatly reduce the chance of freeze ups by the double reducing of pressure with two steps of regulators which makes less chilling actions.
Economy InstallationIn a single stage reduction system, line piping between the container and the appliances must be larger. In contrast, in a second stage reduction system, the smaller size of pipe can be used as it delivers gas at less pressure by two way reduce.
HYR-250
HYR-235C
HYR-2100
HYR-235
2nd Stage Regulator
Inlet Pressure Range : 0.025~0.1 MPa 0.025~0.15 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 35kg/h 35kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 3/4B PT 3/4BOutlet Connection Size : PT 1B PT 1BApplication : Commercial & Industrial Commercial & Industrial
Inlet Pressure Range : 0.025~0.15 MPa 0.04~0.1 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 100kg/h 100kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : 50-10K Flange 50-10K Flange Outlet Connection Size : 50-10K Flange 50-10K Flange Application : Commercial & Industrial Commercial & Industrial
Inlet Pressure Range : 0.025~0.15 MPa 0.04~0.4 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 50kg/h 50kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 3/4B PT 3/4BOutlet Connection Size : PT 1B PT 1BApplication : Commercial & Industrial Commercial & Industrial
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type Low Pressure Type Middle Low Pressure Type
Inlet Pressure Range : 0.04~0.4 MPaSetting Outlet Pressure (P2) : 15, 25 kPaOutlet pressure Range : P2±Within 20%Capacity : 35kg/hInternal Relief Working Pressure : No Relief Inlet Connection Size : PT 3/4BOutlet Connection Size : PT 1BApplication : Commercial & Industrial
Middle Low Pressure Type
HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
22611
6.514
0226
Ø180
116.5
140
Ø180
156
448
323
96267HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
226
116.5
140
226
Ø180
116.5
140
Ø180
156
448
323
96267
HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
226
116.5
140
226
Ø180
116.5
140
Ø180
156
448
323
96267
HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
226
116.5
140
226
Ø180
116.5
140
Ø180
156
448
323
96267
24
HYR-2150C
HYR-2200C
HYR-2200
HYR-2300C
www.hwa-young.com
Inlet Pressure Range : 0.025~0.15 MPa 0.04~0.1 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.8±0.5 kPa P2±Within 20%Capacity : 200kg/h 200kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : 50-10K Flange 50-10K Flange Outlet Connection Size : 50-10K Flange 50-10K Flange Application : Commercial & Industrial Commercial & Industrial
Low Pressure Type Middle Low Pressure Type
Inlet Pressure Range : 0.1~0.4 MPaSetting Outlet Pressure (P2) : 15, 25 kPaOutlet pressure Range : P2±Within 20%Capacity : 150kg/hInternal Relief Working Pressure : No Relief Inlet Connection Size : 50-10K Flange Outlet Connection Size : 50-10K Flange Application : Commercial & Industrial
Inlet Pressure Range : 0.1~0.4 MPaSetting Outlet Pressure (P2) : 15, 25 kPa Outlet pressure Range : P2±Within 20%Capacity : 200kg/hInternal Relief Working Pressure : No Relief Inlet Connection Size : 50-10K Flange Outlet Connection Size : 50-10K Flange Application : Commercial & Industrial
Inlet Pressure Range : 0.1~0.4 MPaSetting Outlet Pressure (P2) : 15, 25 kPa Outlet pressure Range : P2±Within 20%Capacity : 300kg/hInternal Relief Working Pressure : No Relief Inlet Connection Size : 50-10K Flange Outlet Connection Size : 50-10K Flange Application : Commercial & Industrial
Middle Low Pressure Type
Middle Low Pressure Type Middle Low Pressure Type
HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
226
116.5
140
226
Ø180
116.5
140
Ø180
156
448
323
96267
HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
226
116.5
140
226
Ø180
116.5
140
Ø180
156
448
323
96267
HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
226
116.5
140
226
Ø180
116.5
140
Ø180
156
448
323
96267
HYR 2150C~
HWA YOUNG Co.MADE IN KOREA
HWA YOUNG Co.MADE IN KOREA
HYR-235
HYR-250
HYR-235C
OUT
IN
HWA YOUNG Co.MADE IN KOREA
120 143
4444
Ø181
226
116.5
140
226
Ø180
116.5
140
Ø180
156
448
323
96267
2524
2000 SERIES REGULATOR
2000 SERIES 2ND STAGE MIDDLE LOW & LOW PRESSURE REGULATOR 2000 SERIES regulator reduces the inlet pressure range 0.025~0.15 MPa to outlet pressure range with 12~30 kPa in order to supply gas to the combustor.
IntroduceThis regulator’s exterior material is coated by 7 level coating system which possibly makes long lasting use without cracks tear off of paint. It can be installed either horizontal or vertical way by thread type connection and also, it is easy to maintain without dismantle of body.
Feature Easy to MaintainThe casting body makes easy to maintain or replace of internal part without dismantle of body Convenient adjustmentIt is possible to replace orifice according to flow rate of application. Convenient adjustment of pressureThe anti corrosion material of spring enables long lasting use and it is possible to adjust the pressure setting conveniently.Easy to InstallThe regulator makes unrestricted direction of install by rotating of body case. OrificeA variety of size of orifice is available to be replaced based on flow rate of application.
2nd Stage Regulator
26
Inlet Pressure Range : 0.1~0.4 MPa
Setting Outlet Pressure (P2) : 15, 25 kPa
Outlet pressure Range : P2±Within 20%
Capacity : 80kg/h
Internal Relief Working Pressure : No Relief
Inlet Connection Size : PT 1B
Outlet Connection Size : PT 1B
Application : Commercial & Industrial
Inlet Pressure Range : 0.1~0.4 MPa
Setting Outlet Pressure (P2) : 15, 25 kPa
Outlet pressure Range : P2±Within 20%
Capacity : 100kg/h
Internal Relief Working Pressure : No Relief
Inlet Connection Size : PT 1-1/2B
Outlet Connection Size : PT 1-1/2B
Application : Commercial & Industrial
Part Name Material Head Nodular Graphite Cast IronBody Aluminum Die CastingDiaphragm NBR+Cotton (Middle low)Diaphragm Plate SteelLever Steel Adjusting Spring Piano wire Cover Aluminum Die CastingValve Seat NBRRelief Spring STS304 (Stainless) Strainer STS304 (stainless)
Part Name Material Head Nodular Graphite Cast IronBody Aluminum Die CastingDiaphragm NBR+Cotton (Middle low)Diaphragm Plate SteelLever Steel Adjusting Spring Piano wire Cover Aluminum Die CastingValve Seat NBRRelief Spring STS304 (Stainless) Strainer STS304 (stainless)
130
Ø181
162
240.5
231
108
Ø181 139
258
158
2100c
2080C
130
Ø181
162
240.5
231
108
Ø181 139
258
158
2100c
2080C
HYR-2080C & HYR-2100C TYPE The internal relief valve is equipped in low pressure type (2.8 kPa) in order to stabilize the fl ow of gas. Also, the relief valve makes high safety of regulator. The stainless steel strainer at vent can avoid insects or foreign material.The cast iron material for body enables long term use.The adjustable outlet pressure setting design makes wide pressure range.
www.hwa-young.com
HYR-2080C
HYR-2100C
2726
AUTOMATIC CHANGEOVER PRESSURE REGULATOR
AUTOMATIC CHANGEOVER PRESSURE REGULATOR (UNITED & SEPARATED TYPE) This regulator which automatically executes change over function from the service side to reserve side for two separate LPG supply line. The unitized type is integrated first & second stage pressure reducing portion. Separate type regulator is first stage pressure reducing portion on unitized automatic changeover regulator. This regulator must be combined with second stage regulator for use.
Description The main function of automatic changeover regulator is supplying gas without stop by automatic changeover and it is great to be used for the facility which is supposed to supply gas at stable pressure. Those are especially suitable for homes, mobile homes, cottages, construction. And other potable two cylinders installation. Empty containers may be replaced without interrupting consumer’s gas service.
Feature For the connection of the regulator, the PT thread is selected which is international standard to be feasible for connection of piping or hose without extra work. The method for body material is aluminum die casting design with special coating in order to avoid scratch or cracks from outside condition and corrosion, so it made possible to actualize the long lasting life time at once.
The inside material is all corrosion resistance to make it stable performance for long time.Also, it provides union connection for outlet connection to make it easy installation and dismantle.
Automatic Changeover Regulator
28
INLET PRESSUREOUTLET PRESSUREATMOSPHERE PRESSURE
UNION
DIAPHRAGM ASSEMBLY(LOW PRESSURE)
CONTROL SPRING(LOW PRESSURE)
ADJUSTING SCREW
LEVERVALVE STEM
DIAPHRAGM ASSEMBLY
CONTROL SPRING
REGULATOR ORIFICE
VALVE STEM
SPINDLE
REGULATOR ORIFICE(LOW PRESSURE)
Principle of Operation The Unitized changeover regulator can make automatically changeover one gas cylinder to another one without stop supplying of gas when it has run out of gas. The regulator is unitized with 2nd stage 1st reduction and 2nd stage 2nd reduction regulators. The 2nd stage 1st reduction regulator is equipped with change over function.
By consumption of gas, the pressure inside of 2nd stage 2nd reduction regulator is being lowered and the spring inside of it tends to push the diaphragm until makes it parallel to the pressure rate by reduction side of regulator. At this time, the lever that is connected with diaphragm works to move the valve seat backwards and then the gas is being supplied with reduced pressure through 2nd stage 1st reduction to 2nd stage 2nd reduction regulator.
When stop consumption of gas, the pressure inside of 2nd stage 2nd reduction regulator is being increased and this makes push up the diaphragm by spring until parallel to the setting pressure rate and then the lever that is connected with diaphragm makes the valve seat move towards to block the gas fl ow.
When Consumption of Gas
Stop Consumption of gas
www.hwa-young.com
1
2
43
5
6
8
7
109
1113
12
14
15 1617 18
19
1 BODY 11 SPINDLE
2 COVER 12 DIAPHRAGM(LOW PRESSURE)
3 MID PRESSURE ADJUST SPRING 13 DIAPHRAGM PLATE(LOW PRESSURE)
4 LOW PRESSURE ADJUST SPRING 14 SAFETY SPRING
5 BRACKET 15 ORIFICE(LOW PRESSURE)
6 STRAINER 16 LEVER(LOW PRESSURE)
7 VALVE ROD 17 VALVE SEAT(LOW PRESSURE)
8 VALVE SEAT 18 VALVE STEM( LOW PRESSURE)
9 DIAPHRAGM PLATE(MID PRESSURE) 19 UNION
10 DIAPHRAGM(MID PRESSURE)
Construction
2928
Automatic Changeover Regulator
MR1 R2
Regulator Gas Meter Gas Burner
Container Group
2.55 - 3.3 kPa 2.0 - 3.3 kPa
B
(20 - 33mbar)(25.5 - 33mbar)
Automatic Changeover Pressure Regulator (Unitized Type)
0.032-0.083 MPa
Container Group R1
RegulatorGas Meter
M2.3 - 3.3 kPa
BGas Burner
M BGas BurnerGas Meter
R2
R2
2nd Stage Regulatorfor two stage reduction
(0.32-0.83bar)
(23 - 33mbar)
Automatic Changeover Pressure Regulator (Separate Type)
Pressure Loss:within 0.007 MPa
Automatic Unitized Changeover Pressure Regulator consists of changeover and second stage regulators (two stage reduction).The economy design that is possible to be replaced only changeover side or regulator side if there is problem caused by impact or corrosion.
Installation Drawing
AUTOMATIC CHANGEOVER PRESSURE REGULATOR (UNITIZED TYPE) It is one of our commonly use regulators. It is feasible for use more than one LPG gas cylinder at the same time by equipped unitized changeover function with 2nd stage 1st reduction regulator and 2nd stage 2nd reduction regulator in one body. Once the one gas cylinder has run out of gas, the regulator makes automatically changeover to another cylinder to supply gas at stabilized pressure rate without stop supplying of gas.
HAC-6
HAC-12
HAC-35
HAC-8
HAC-20
INLET(PT1/4",8A)
OUTLET
INLET(PT1/4",8A)
81
PT1/2
100INLET
PT1/2
PT3/4 UNIONOUTLET
INLET
134
PT1/2PT1/2
PT3/4
INLET INLET
OUTLET
INLET INLET
134
OUTLET
PT1/2 PT1/2
PT 1" UNION
WA
OH
Y
G
U
Co
N
KS
A 9 7 - 1 0 -
0
46K S B 6 2 13
품
질보 증 : 2 년
Q: 6
kg/ h
P: 0 . 1~ 1 . 5 6MPa R :2 . 8kP a
L . P. G R EGULATOR
HWA YO
UN
G C O .
L.P.G
WA
H
OY U
O.
GN
C NY O UL.P.G
H
AW O.
G C
MODEL : HAC-6, 8 MODEL : HAC-12
MODEL : HAC-35MODEL : HAC-20
INLET(PT1/4",8A)
OUTLET
INLET(PT1/4",8A)
81
PT1/2
100INLET
PT1/2
PT3/4 UNIONOUTLET
INLET
134
PT1/2PT1/2
PT3/4
INLET INLET
OUTLET
INLET INLET
134
OUTLET
PT1/2 PT1/2
PT 1" UNION
WA
OH
Y
G
U
Co
N
KS
A 9 7 - 1 0 -
0
46K S B 6 2 13
품
질보 증 : 2 년
Q: 6
kg/ h
P: 0 . 1~ 1 . 5 6MPa R :2 . 8kP a
L . P. G R EGULATOR
HWA YO
UN
G C O .
L.P.G
WA
H
OY U
O.
GN
C NY O UL.P.G
H
AW O.
G C
MODEL : HAC-6, 8 MODEL : HAC-12
MODEL : HAC-35MODEL : HAC-20
INLET(PT1/4",8A)
OUTLET
INLET(PT1/4",8A)
81
PT1/2
100INLET
PT1/2
PT3/4 UNIONOUTLET
INLET
134
PT1/2PT1/2
PT3/4
INLET INLET
OUTLET
INLET INLET
134
OUTLET
PT1/2 PT1/2
PT 1" UNION
WA
OH
Y
G
U
Co
N
KS
A 9 7 - 1 0 -
0
46K S B 6 2 13
품
질보 증 : 2 년
Q: 6
kg/ h
P: 0 . 1~ 1 . 5 6MPa R :2 . 8kP a
L . P. G R EGULATOR
HWA YO
UN
G C O .
L.P.G
WA
H
OY U
O.
GN
C NY O UL.P.G
H
AW O.
G C
MODEL : HAC-6, 8 MODEL : HAC-12
MODEL : HAC-35MODEL : HAC-20
INLET(PT1/4",8A)
OUTLET
INLET(PT1/4",8A)
81
PT1/2
100INLET
PT1/2
PT3/4 UNIONOUTLET
INLET
134
PT1/2PT1/2
PT3/4
INLET INLET
OUTLET
INLET INLET
134
OUTLET
PT1/2 PT1/2
PT 1" UNION
WA
OH
Y
G
U
Co
N
KS
A 9 7 - 1 0 -
0
46K S B 6 2 13
품
질보 증 : 2 년
Q: 6
kg/ h
P: 0 . 1~ 1 . 5 6MPa R :2 . 8kP a
L . P. G R EGULATOR
HWA YO
UN
G C O .
L.P.G
WA
H
OY U
O.
GN
C NY O UL.P.G
H
AW O.
G C
MODEL : HAC-6, 8 MODEL : HAC-12
MODEL : HAC-35MODEL : HAC-20
INLET(PT1/4",8A)
OUTLET
INLET(PT1/4",8A)
81
PT1/2
100INLET
PT1/2
PT3/4 UNIONOUTLET
INLET
134
PT1/2PT1/2
PT3/4
INLET INLET
OUTLET
INLET INLET
134
OUTLET
PT1/2 PT1/2
PT 1" UNION
WA
OH
Y
G
U
Co
N
KS
A 9 7 - 1 0 -
0
46K S B 6 2 13
품
질보 증 : 2 년
Q: 6
kg/ h
P: 0 . 1~ 1 . 5 6MPa R :2 . 8kP a
L . P. G R EGULATOR
HWA YO
UN
G C O .
L.P.G
WA
H
OY U
O.
GN
C NY O UL.P.G
H
AW O.
G C
MODEL : HAC-6, 8 MODEL : HAC-12
MODEL : HAC-35MODEL : HAC-20
Inlet Pressure Range : 0.1~1.56 MPa 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.55~3.3 kPa P2±Within 20%Capacity : 6kg/h 6kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 1/4 PT 1/4Outlet Connection Size : PT 3/4 Union PT 3/4 Union Application : Household & Commercial Household & Commercial
Inlet Pressure Range : 0.1~1.56 MPa 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.55~3.3 kPa P2±Within 20%Capacity : 12kg/h 12kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 1/2 PT 1/2Outlet Connection Size : PT 3/4 Union PT 3/4 Union Application : Commercial & Regidential Commercial & Regidential
Inlet Pressure Range : 0.1~1.56 MPa 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.55~3.3 kPa P2±Within 20%Capacity : 35kg/h 35kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 1/2 PT 1/2Outlet Connection Size : PT 1 Union PT 1 Union Application : Commercial & Regidential Commercial & Regidential
Inlet Pressure Range : 0.1~1.56 MPa 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.55~3.3 kPa P2±Within 20%Capacity : 8kg/h 8kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 1/4 PT 1/4Outlet Connection Size : PT 3/4 Union PT 3/4 Union Application : Household & Commercial Household & Commercial
Inlet Pressure Range : 0.1~1.56 MPa 0.1~1.56 MPaSetting Outlet Pressure (P2) : 2.8 kPa 15, 25 kPaOutlet pressure Range : 2.55~3.3 kPa P2±Within 20%Capacity : 20kg/h 20kg/hInternal Relief Working Pressure : 7.0±1.4 kPa No Relief Inlet Connection Size : PT 1/2 PT 1/2Outlet Connection Size : PT 3/4 Union PT 3/4 Union Application : Commercial & Regidential Commercial & Regidential
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type
Low Pressure Type Middle Low Pressure Type
30
Inlet Pressure Range : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.032~0.083 MPaCapacity : 10kg/hInlet Connection Size : PT 1/2 B Outlet Connection Size : PT 1/2 B Application : Commercial & Industrial Application : Commercial & Residential
Inlet Pressure Range : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.032~0.083 MPaCapacity : 20kg/hInlet Connection Size : PT 1/2 B Outlet Connection Size : PT 1/2 B Application : Commercial & Industrial Application : Commercial & Residential
Inlet Pressure Range : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.032~0.083 MPa Capacity : 15kg/hInlet Connection Size : PT 1/2 B Outlet Connection Size : PT 1/2 B Application : Commercial & Industrial Application : Commercial & Residential
Inlet Pressure Range : 0.1~1.56 MPaSetting Outlet Pressure (P2) : 0.032~0.083 MPaCapacity : 35kg/hInlet Connection Size : PT 1/2 B Outlet Connection Size : PT 1/2 B Application : Commercial & Industrial Application : Commercial & Residential
AUTOMATIC CHANGEOVER PRESSURE REGULATOR (SEPARATED TYPE) It is one of our commonly use regulators. Regulator makes automatically changeover to another cylinder to supply gas at stabilized pressure rate without stop supplying of gas. Separated type regulator is fi rst stage pressure reducing portion on unitized automatic changeover regulator. This regulator must be combined with second stage regulator for use.
104
5084
24.6
318450
100
MODEL : HAX-10
104
5084
24.6
318450
100
MODEL : HAX-10
C O.
AW
H
YOUNG
L.P.G
Ø124
134
157
51
67
40
MODEL : HAX-20
C O.
AW
H
YOUNG
L.P.G
Ø124
134
157
51
67
40
MODEL : HAX-20
HAX-10
HAX-20
HAX-15
HAX-35
www.hwa-young.com
MR1 R2
Regulator Gas Meter Gas Burner
Container Group
2.55 - 3.3 kPa 2.0 - 3.3 kPa
B
(20 - 33mbar)(25.5 - 33mbar)
Automatic Changeover Pressure Regulator (Unitized Type)
0.032-0.083 MPa
Container Group R1
RegulatorGas Meter
M2.3 - 3.3 kPa
BGas Burner
M BGas BurnerGas Meter
R2
R2
2nd Stage Regulatorfor two stage reduction
(0.32-0.83bar)
(23 - 33mbar)
Automatic Changeover Pressure Regulator (Separate Type)
Pressure Loss:within 0.007 MPa
3130
LIQUID CHANGEOVER DEVICE (HLX-301)
Adjusting pressure1. Automatic changeover device equipped two types of
spring which allows accurate and comfortable control the demand pressure.
2. Regulator apply pressure range from 0.5 to 2.0kgf/cm², if require to adjust demand pressure, please check adjusting knob length.
3. To adjust demand control, there is a pressure control screw either turning to clockwise or counterclockwise. Be sure that adjusting knob provides various pressure demands, and suitable pressure has been released.
* Outlet pressure is adjustable by setting the length of adjusting screw. When it’s needed, Please refer to the below table.
* Note that this product approved performance from Korea Gas Safety Corporation. The warranty is a year from customer purchased.
Model HLX-301AService Liquefied Petroleum Gas (LPG : Liquid Condition)Max. Capacity 300 kg/hInlet Pressure Range (Changeover Pressure +△P) ~1.56 MPa (15.6 kgf/cm²)Setting Changeover Pressure 0.05 ~0.2 MPa (0.5~2.0 kgf/cm²)Internal Pressure 3 MPa (30 kgf/cm²)Inlet / Outlet Connections 20K-20A FlangeInlet / Outlet Length 315mm X 170mmWeight 9.1kg
Capacity (Kg/hr) 100↓ 100~150 150~200 200~250 250↑△P
(kgf/cm²)0.03 MPa
(0.3 kgf/cm²)0.07 MPa
(0.7 kgf/cm²)0.11 MPa
(1.1kgf/cm²)0.14 MPa
(1.1kgf/cm²)0.18 MPa
(1.1kgf/cm²)
Setting Interval 21mm 16mm 12mm 7mm
Setting ChangeoverPressure
0.05 MPa(0.5 kgf/cm²)
0.1 MPa(1 kgf/cm²)
0.15 MPa(1.5kgf/cm²)
0.2 MPa(2kgf/cm²)
Automatic Changeover regulators prevent gas outages by switching supply cylinders over to the reserve cylinder automatically when the primary cylinder is near empty. When the primary cylinder is depleted causing the changeover to occur a red indicator will appear signifying the reserve cylinder in now in use and the primary cylinder can be refilled without loss of service.Reduced the damage from the deterioration by metal abrasion, even though use valve often frequencies. This regulator equipped convert handle which indicates “serve“ and “reserve”, and diaphragm operation would help adjusting demand pressure.This compact designed for especially space l imitation, and l ight weight helps to easier installation.
Example) in case of changeover pressure 0.05MPa, Capacity 190kg/h 0.05+0.11=0.16 MPa (changeover Pressure +△P)
About inlet pressure △ P, Please refer to below table
Specification
SettingInterval
Changeover PressureSetting Bolt
Locknut
Manual Changeover Knob
Liquid Changeover Device
32
17089
315
APPR
OX. 3
76
99
45°
45°
HWA YOUNG CO.INLET INLET
OUTL
ET
합격Q.A
컴팩트형 액자동 절체기모델번호 [ HLX-301A ]
화 영 상 사HWA YOUNG CO.
[ 1년 ]사용가스 [ L.P.G ]
SERIAL NO.품질보증기간
0411001
A indicates serve, and B indicates reserveFigure 1 Pressure from A is lower than demand pressure which means that changeover operates properly. Therefore, gas flows from B. ( At this time, indicator shows red)Figure 2 Reserve provides gas to regulator at this moment. To close valve from A, turn convert handle to B which allows replacing new gas cylinders for A. (indicator shows red to colorless). Figure 3. The other Pressure from B has lower than demand pressure now, so that A supplies gas to the regulator. (indicators changes from colorless to red).Figure 4. Gas provided from the A, as same operation as fi gure 2, to close valve from B, turn convert handle from A to B which allows refi lled the gas cylinders for B
Maintenance ① Replacing a gas cylinder, must inspect the indicator and follow
below procedure. 1) When indicator turned in red, (assuming indicator direction
is serve) gas is being supplied from the reserve cylinder. 2) Closing service valve and high pressure pipe valve, and turn
convert to opposite. 3) Note that do not replace a gas cylinder without procedures
above. 4) Replace a new cylinder after inspection has been made.
② After replacing a new cylinder, MUST check an indicator turned to colorless. If indicator still remains red, slowly redo the procedure above.
③ After all pressure has been released from the regulator, check an indicator point to proper direction (either serve or reserve), then inspect that there is a gas leak in the cylinder valve, inlet fi tting, high pressure hose, or regulator seat.
④ Do not attempt to load any heavy matters on the regulator for safety issue.
⑤ Do not attempt move or place a cylinder when connected with high pressure hose.
Manual changeover* User can change from reserve or serve manually if indicator function in case of not working properly.
① Colorless of indicator means serve, however, it may be unreleased gas from the serve. In this problem, push manual changeover button to release gas fl ow properly.
② At the time pushing manual changeover button, indicator turns to red mark. This procedure makes to change from “serve” to “reserve” .
③ Must turn convert handle to opposite direction, after indicator appeared red mark.
* Do not attempt to push manual changeover knob with hammer. ** Do not keep pushing knob during processing.
Operation
Dimension
B SideA Side
A Side B Side
B SideA Side
A Side B Side
A Side B Side
<Fig. 2><Fig. 1>
Indicator Spring
Linkage Pin
Conver Pin
Convert Cam
Diaphragm
Linkage Iron
<Fig. 4><Fig. 3>
Red Mark
Crank Road
Crank Device
Adjusting Spring
ConvertHandle
IndicatorWindows
ManualChangeoverKnob
ConvertHandle
www.hwa-young.com
3332
HWA YOUNG GAS HOSE
This product has been approved by KGS (Korean Gas Safety Association) through passing all the quality standard and safety tests which are higher specification than any other nations for LPG or LNG application. For your safety and correct using, please follow the steps of installation as below. Otherwise it may cause failure of safety and lead to critical problem. HWA YOUNG’s LN Gas Hose is feasible to use for delivery of LP Gas or LN Gas from propane gas cylinder or high pressure of natural gas through piping to combustor safely.
Feature The outer layer is made of special material in order to endure long lasting from outside condition such as temperature change and direct sunlight. The mid layer which is made of thin metal wire can avoid the risk of accident from worn out caused by high temperature or pressure or intentional cutting. Also, the inner layer is specialized for oil resistance and possible to completely avoid the gas leakage. These special three layers actualized Hwa Young’s LN Gas Hose to secure both safety and durability.
Caution- Keep away from the Flame. The flame causes hose damage and
might cause explosion.- The leakage might be caused if use Y connection or T connection.- Replace the hose if there is crack or color fade.- Intentional disconnection or cut of hose is not allowed. (It might cause leakage and explosion.)- Replace the hose if the hose were exposed to high temperature
or oily condition for long time.- Do not place the hose behind the refrigerator or place where
that can not visualize the hose easily because the hose should visually checked periodically.
- If the hose is bent or twisted for long time, the durability of hose might be affected and shortened the life time.
GAS HOSE and Accessories
34
Product Name : JUMBO HOSE
Standard : KS M 3813
Dimension :
Inner Dia : 9.5mm ± 0.7mm
Outer Dia : 22mm or below
Length: 30m ± 0.3
Color : White
Working Pressure : 196 kPa or below
Burst Pressure : 3.92 MPa or above
Working Temperature : -20°C
Product Name : LPG HOSE
Standard : KS M 3813
Dimension :
Inner Dia : 9.5mm ± 0.7mm
Outer Dia : 22mm or below
Length: 50 ± 0.5
Color : Orange
Working Pressure : 196 kPa or below
Burst Pressure : 3.92 MPa or above
Working Temperature : -20°C
Liquid Propane & Natural Gas HoseFeature• No. 1 rated consumer reliability & satisfaction for both domestic & global market. Over 90% market share in domestic market• The special outer layer with PVC material makes realization for long lasting use without any problem which can be caused by
various weather condition or direct sun light.• Completely avoided any leakage. The inner layer with special coated PVC material resists oil & gas.• Outstanding durability and safety by layered structure.• The quality is guaranteed by Korea Gas Safety who has very strict standard to regulate quality in gas product industry in Korea.• Completely avoids any safety accident from damage to hose by metallic wired layer. • The fl exible makes easy to install in limited space by bending of hose without any damage because it has excellent restoring force.
www.hwa-young.com
3534
Model HYP-10-RHApplication LP GAS
Type Vapor
Length 1000 mm (1M)
Inlet Connection Size Pol Handle L.H W22.5 x 14T
Outlet Connection Size PT1/4 B
Applicable Pressure 1.8 MPa (18kgf/cm²) or below
Inner Diameter Ø6
Outer Diameter Ø12
Model HYP-10-AV-FApplication LP GAS
Type Liquid
Length 1000 mm (1M)
Inlet Connection Size Pol Handle L.H M22 X P1.5
Outlet Connection Size PT1/4 B
Applicable Pressure 1.8 MPa (18kgf/cm²) or below
Inner Diameter Ø6
Outer Diameter Ø12
Specification Specification
FeatureStrengthened safety probability by coating inside of hose to make possible to avoid leakage completelyHigh strength synthetic sand is applied for mid layer to minimize the damage from high pressure usageSpecial oil resistant and anti wear compound rubber is applied for long lasting use and high durability as well as excellent safety which are strong points.
It is possible to be connected free in any direction with gas cylinder or pipe regardless of any size of space by its high flexibility. In addition, it is designed with pol handle for inlet and PT thread for outlet connection in order to connect directly to LPG cylinder and pressure regulator for comfort and safety. For the connection material of inlet and outlet, the brass is selected to avoid corrosion to make high durability..
The liquid type of design’s one of the main features is when over flow of gas is occurred, the relief valve which equipped inside of hose is being mechanically sensed and operated to block the gas flow. It makes possible to replace the LPG gas cylinder without back flow of gas.
HYP-10-AV-F Principle of Operation When connected condition of hose’s inlet side with gas cylinder or pipe, the valve is being opened by pushed from hose’s nipple to make influx of gas. On the other hand, when disconnecting the hose, the spring force makes valve to move towards the inlet side and block the way of gas flow.
HIGH PRESSURE RUBBER HOSE (PIG TAIL HOSE)
GAS HOSE and Accessories
CLOSED OPEN
PUSH BUTTON
POLE HANDLE
VALVESPRING SPRING
VALVEPUSH BUTTON
POLE HANDLE
36
Dimensions
Inside Diameter Ø9.5 ± 0.7 mm (Ø3/8 inch)
Outside Diameter Ø22 mm below
Length 1M/1.3M/1.5M/1.8M/2M/2.5M/3M
Working Pressure 196 kPa or below
Burst Pressure 4 MPa above
Feature
Reinforced Safety• Patented optimum connection to prevent gas leakage with
exclusive clamp• Prevent hose cutting or damage using flexible metal
materials inside hose• Special yarn middle layer is designated for protecting inside
layer from heating or fl ame etc.• Safety character is reinforced with 4 layer construction
Elegant external appearance• As high qualifi ed gas hose, up-grade kitchen interior design• Easy to remove hose surface dust or other materials
Working effi cient and convenience• Working effi ciency is excellent using exclusive clamp• Choice 1M/1.3M/1.5M/1.8M/2M/2.5M/3M hose length
according to install site
Specifi cation
• Applicance using city gas or L.P gas, Max Pressure of 13 inch W.C (3.3 kPa)
• Easier hose connection & disconnection, thus suitable for portable applicances
• Engineer plastics material provides high impact, high temperature, fl ame retardant and gas tight characteristics
SMART HOSE
QUICK COUPLER
www.hwa-young.com
3736