FEATURED ARTICLES

Safety NewsEssence of Good Housekeeping

ISSUE14/ISSN1793-1665JULY2009

02 ENHANCING SAFETY THROUGH GOOD HOUSEKEEPING PRACTICES

05 ENHANCEMENT OF CONTRACTORS’ ENVIRONMENTAL, SAFETY & SECURITY ASSESSMENT

08 INTEGRATED SUPERVISORY CONTROL SYSTEM IN RAIL TRANSIT SYSTEMS

10 MANAGING PEDESTRIAN SAFETY AT SIGNALISED JUNCTION

13 ACCIDENT STATISTICS

14 EDITORIAL PAGE

Enhancing Safety Through GoodHousekeeping Practices

Introduction

A clean and tidy workplace enhances a company’s image and gives the most visible evidence of its commitment and concern for safety and health.

Poor housekeeping creates hazards for various types ofaccidents like fire, struck by objects, trip, slip and fall; it is afactor in a wide variety of accidents and injuries. Generally, housekeeping at the construction worksite is ineffectively planned, implemented and monitored.

Apart from the safety hazards, good housekeeping practice is able to keep pollutants out of our storm drain system and reservoirs. Materials swept, blown, or washed into the storm drains end up in these open waters where they degrade water quality and harm aquatic life. In general, wastewater discharged to the storm drains is illegal.

Hence, it is imperative for contractors to institute a campaign and inspection program to identify and control potentialdischarge of pollutants to the storm drain system. Some of the pollutants that can get into the storm drain system include grease, pesticides, paints, cement and yard wastes. With good housekeeping practices in their daily activities, it will help to reduce or eliminate their contribution to storm waterpollution.

BasedonLTAaccidentstatistics in2008,poorhousekeepingcontributed directly to around 6% and indirectly to another 6% of reportable accidents.

This article aims to provide knowledge sharing platform on some good initiatives and practices practiced by LTA contractors with highlights of some sound housekeeping managementconcepts.

Evidences of good housekeeping at a construction worksite are:

1. Clear delineated zones for:

a. Well labeled storage areas for different types of construction material and equipment; b. Unobstructed access and egress paths; and c. Holding areas for waste material.

2. Tidiness and cleanliness experienced in:

a. The entire compound of the construction worksite; b. The canteen and resting areas; and c. The site offices.

3. Well documented processes that standardize the high housekeeping standard throughout the entire set-up.

02

SA

FE

TY

NE

WS

En

han

cing

Safety T

hro

ug

h G

oo

d H

ou

sekeepin

g P

ratices

The benefits of implementing a good housekeeping system are:

• fewerstruckbyobjects,tripping,slippingandfalling accidents;• reducedrisksoffirehazardandexposuretohazardous substances;• speedupevacuationinanemergency;• betterhygienicconditions;• reducedmaterialshandling;• minimizedamagetoequipmentsandmaterials;• betterinventorycontroloftoolsandmaterials;• moreeffectiveuseofspace;• developingteamworkandinstillgoodhabits;• improvedmorale;and• improvedproductivity.

Legislation

Applicable legislation associated with housekeeping:

1. The Workplace Safety and Health (WSH) Act states that it is the duty of occupier of workplace to take, so far is as reasonably practicable, such measure to ensure that all means of access to or egress from the workplace are safe and without risks to health to every person within those premises.

2. The WSH (General Provisions) Regulations require all goods to be stored, stacked or placed in a manner that is safe and does not cause any obstructions.

3. The WSH (Construction) Regulations require the occupier to ensure that debris shall not be allowed to accumulate so as to constitute a hazard in the worksite.

Examples of Good Housekeeping Initiatives and Practices at LTA Worksites

Zoning

For worksites of sizeable area, it is segregated into zones for better management of housekeeping. Housekeeping teams are set-up in accordance to the number of zones. Each team is formed up with adequate number of workers. The housekeeping teams are assigned to the various zones to carry outhousekeeping tasks on a daily basis.

Facilities

Facilities provisions are important in encouraging properdisposal of waste and cleanliness of the worksite. Several types of bins are provided at strategic locations catering todifferent wastes. Organic waste bins are provided at all entry/exit points of the worksite including designated resting areas and food consumption areas. Construction wastes bins arelocated near to work areas. There are also bins provided for recycling program to promote an environmentally friendlyculture.

Storage

When materials are delivered to the worksite it is stacked in an orderly manner and barricaded at assigned storage areas with demarcation. Highly flammable materials will be stored away from any point of ignition. Proper planning of storage areas will maximize the usage of the worksite especially for those with space constraint and will reduce the amount of handling, thus, reducing the exposure to hazards. Proper storage will alsoalleviate any damage to equipments and materials.

Mass Housekeeping

Mass housekeeping exercise is organized and conductedregularly with adequate time allocated for the session to ensure effectiveness. To demonstrate commitment, it is led by the main contractor’s management staff.

Inspections

Regular inspections on housekeeping are conducted to ensure wastes are properly disposed and removed from the worksite. It is also to ensure materials are stored in a neat and safe manner at designated locations.

Promotional Activities

To promote good housekeeping on worksite, theme onhousekeeping is broadcast through banners and signage at work areas. Awards are given out by contractors periodicallyin recognition for those with exceptional effort in goodhousekeeping. This will motivate everyone to strive towards a clean, tidy and orderly workplace.

Awareness

To instill a good housekeeping culture, staff and workers are made aware of the housekeeping standards during their Safety Induction Course. They are also constantly reminded through Tool-BoxMeetings.

To build upon these good initiatives and practices, a widelyregarded housekeeping management concept - 5S can beadopted to manage housekeeping effectively.

03

SA

FE

TY

NE

WS

Figure1:ProvisionofBinsforWastes&RecycleProgram

Figure 3: Clean and Orderly Worksite

Figure2:ProperMaterialStoragewithDemarcationandBarricades

En

han

cing

Safety T

hro

ug

h G

oo

d H

ou

sekeepin

g P

ratices

5S Concept for Good Housekeeping

5S is a Japanese quality management concept based on acyclical methodology. It is a method for organizing a workplace and often referred as a housekeeping method. The mainobjectives are to enhance morale, safety and efficiency.

This management model is based on 5 Japanese words seiri, seiton, seiso, seiketsu and shitsuke. Generally, these 5 Japanese words mean organize, orderliness, cleanliness, standardize and discipline respectively.

This Japanese management concept is widely practiced byorganizations around the world.

Reference1. 5S Good Housekeeping, Singapore Productivity and StandardsBoard.

Leong Choong YiokSenior Executive, Safety and Health

Safety Division

Seiri (Organize)This focuses on sorting out unnecessary items in the workplace and disposing it away. (Figure 5 shows a guide to classifying unnecessary items).

Seiton (Orderliness)This relates to arrange necessary items in a neat, proper manner for easy retrieval and to put back in their proper locations.(Figure 6 shows a guide to classifying necessary items).

Seiso (Cleanliness)This describes the importance to clean and inspect the workplace thoroughly.

Seiketsu (Standardize)This is about maintaining a high standard of workplaceorganization by keeping everything clean and orderly at all times.

Shitsuke (Discipline)This conveys the need to train people to follow good housekeeping standards religiously, and to observe self-discipline through continuous practice.

04

SA

FE

TY

NE

WS

Figure 4: 5S Cyclical MethodologySource:http://www.lean.state.mn.us/photos.htm

Figure 5: Guide to Classifying Unnecessary Items

Conclusion

The Japanese 5S Concept for Good Housekeeping goesbeyond regular cleaning of the worksite. It stresses on theimportance of proper waste storage and regular removal,structured zoning for storage of construction materials, and safe access and egress pathways, to ensure safety and efficiency of worksite operation. The 5S Concept of Good Housekeeping which is relevant to the construction sites promotes that “a safe worksite is an efficient and productive worksite”.

Figure 6: Guide to Classifying Necessary Items

Enhancing Safety Through GoodHousekeeping Practices (cont’d)

En

han

cing

Safety T

hro

ug

h G

oo

d H

ou

sekeepin

g P

ratices

Environmental Management

Items

Solid WasteManagement

Adequate waste bins

On-site separation to recover reusable and recyclable wastes

Frequent disposal of wastes

Noise Control[If Applicable]

Efforts to reduce noise at source

Efforts to reduce noise at transmission pathways

Employment of simple techniques

Use of sound-reduced machinery

Effective positioning of machinery

Water PollutionControl

Adequate provisions to prevent leakages

No sign of spillages / leakages

Air Pollution Control No emission of black smoke

Periodic wetting of access routes

Arresting of dust at source / proper shielding of dusty operations

Regular maintenance of machinery

Mosquito Control Effective vector control plan

Pitched roof for all site containers

Larvicides/ Bacillus thuringiensis israelensis (Bti) placed in stagnating water that cannot be cleared

Effective housekeeping

Ovitraps/ gravitraps used on site for moni-toring of potential mosquitoes breeding

Effective drainage of stagnating water

Introduction

The Annex of ESS assessment was first introduced in 2005 with its enhanced version made in 2008. The major difference between the original and the enhanced version is the increased weightage of environmental scoring from 5% to 16% of the entire ESS assessment, with the rest of the weightage attributing to the safety aspects.

Reasons for Enhancement

This is due to the increased importance and awareness of the environmental issues during the construction phase. Moreimportantly, it was found that with this ESS assessment,the environmental standard of the sites had improvedtremendously over the years.

In order to further improve the site environment performance, a few areas had been enhanced in this ESS assessment. These include:1. Updating and implementation of earth control measures (ECM) plan by the Qualified Erosion Control Professional (QECP);2. Ensuring separate bin for food waste; and3. Ensuring frequent waste disposal.

Thus, the enhanced Annex of ESS assessment will address these areas on a more holistic manner and to improve on the original assessment.

Objective

The objective of the Annex of ESS assessment is to monitor the contractor ’s environmental performance, by providingassessment criteria to assess the respective site’s monthlyenvironmental performance.

The following paragraphs serve to provide an overview of the enhancement of the Annex of ESS assessment and to provide guidelines of the assessment to the readers.

Enhanced Annex of ESS Assessment

The enhanced Annex of ESS Assessment is based on six major environmental aspects, shown in Figure 1.

Environmental Management

Items

Earth ControlMeasures

Updated ECM plan by QECP

Effective maintenance regimes

Concentration of total suspended solids (TSS) discharged < 50mg/L

Prevention of earth waste dropped from construction vehicles

Figure 1: Enhanced Annex of ESS Assessment

Guidance for AssessmentEarth Control Measures

Important aspects that need to consider when performing the assessment include:

1. Updated ECM Plan by QECP

A good site must have an updated ECM plan recommended by the QECP and approved by PUB, corresponding to the same phase of construction at that time and implementing the updated ECM plan on site.

2. Effective Maintenance Regimes

Sites must implement effective sediment control facilities. They must be effectively maintained such that they can be performed to its best capability at all times. These facilities include the silt traps, silt fences, water treatment plant, perimeter drain and washing bay.

Enhancement of Contractors’ Environmental, Safety & Security (ESS) Assessment

05

SA

FE

TY

NE

WS

En

han

cemen

t of C

on

tractors’ E

nviro

nm

ental, S

afety & S

ecurity (E

SS

) Assessm

ent

Figure 4: Samples of Discharged WaterFigure 2: An Effective Silt Fence

For example, an effective silt fence must be embedded at least 200mm into the ground for firm anchoring. There must be weekly inspection; repairing fences that are damaged; and removing of sediment when it reaches one-third of the height of the fence.

3. Adequate Protection of Exposed Earth

Minimal area of exposed earth across the entire site and using proper covers will dictate a good site.

For example: 1. Bare slope can be turfed up when no works are expected to be performed for more than 1 month. 2. Canvas sheet weighed down by stones can be used as a temporary measure when works are expected to be performed within a week. 3. Exposed earth can be filled with hard core to prevent erosion.

4. Concentration of TSS Discharged < 50mg/L

A real-time total suspended solids

5. Prevention of Earth Waste Dropped from Construction Vehicles

No traces of littering of earth or construction waste from construction vehicles onto public roads shall be tolerated.

Solid Waste Management

Important aspects that need to consider when performing the assessment include:

1. Adequate Waste Bins

A sufficient number of covered bins (not overflowing) must be kept closed and a separate bin must be allocated for organic waste.

2. On-site Separation to Recover Reusable and Recyclable Wastes

Provision of storages for different materials such as metals; papers; plastic; glasses; and timber shall be made on site, ensuring that these separated materials were removed from site to recycling facilities.

3. Frequent Disposal of Wastes

Organic waste must be removed daily with frequent disposal of construction waste, ensuring no over- flowing situation on site.

Figure 3: Protection of Exposed Earth

Noise Control (If applicable)

Noise will only be factored into the as-sessment if there is any building within 150m from the boundary of the site.

Important aspects that need to consider when performing the assessment include:

1. Efforts to Reduce Noise at Source

The use of effective acoustic enclosures or noise panels installed at noise emission outlets of machines is as shown below.

To ensure effectiveness, the side of noise barrier with louvers shall face the noise source, while the flat side shall face the noise recipient.

2. Efforts to Reduce Noise at Transmission Pathways

A good site will have an effective installation of barriers: the height and length of the barrier must be adequate to shield the noise propagating to the noise sensitive receivers (NSRs).

These portable noise barriers should move along with the noisy operations on site.

3. Employment of Simple Techniques

A good site will have workers inculcated with good environmental consciousness. Among other things, they can apply simple techniques such as keeping all machinery covers closed and laying rebars down properly instead of letting them go from a standing position will certainly help to alleviate the noise produced. Driver has a duty to ensure that the engine is not left idling when

Figure 5: An Effective Installation of Barriers

(TSS) monitoring device, with a SMS-system in the event of exceeding the 50 mg/L mark, shall be used at sites (eg. DTL1 & MCE) discharging water into the marina barrage.

06

SA

FE

TY

NE

WS

En

han

cemen

t of C

on

tractors’ E

nviro

nm

ental, S

afety & S

ecurity (E

SS

) Assessm

ent

Enhancement of Contractors’ Environmental, Safety & Security (ESS) Assessment (cont’d)

it is not in use nor exerting more power than necessary during operations.

Most importantly, machinery deployed on sites must be regularly maintained by certified and trained mechanics.

4. Use of Sound-Reduced Machinery

It is recommended to utilize machinery that is certified to be sound-reduced by manufacturers and avoid the use of old and poorly maintained machinery.

5. Effective Positioning of Machinery

Place noisy machinery behind natural barriers / structures on site or face the noise emission outlets away from residents. These are some of the good practices that should be implemented on site.

Water Pollution Control

Important aspects that need to consider when performing the assessment include:

1. Provisions to Prevent Leakages

For the permanent storage of chemicals and hydrocarbons, a standard bund wall must be built with a chemical resistant coating in the inner face of the wall. For the temporary storage, a standard spill tray with a volume of 110% of the biggest drum stored must be provided.

2. No Sign of Spillages / Leakages

There shall be no traces of dark spot on the ground and no water ponding in spill trays / bund wall.

Air Pollution Control

Important aspects that need to consider when performing the assessment include:

1. No Emission of Black Smoke

There shall be no black smoke emi t t ing f rom mach inery and equipment for more than 5 minutes in an hour.

2. Periodic Wetting of Access Routes

Water used to wet the ground regularly shall be from a recycled source of water (water treatment plant).

3. Arresting of Dust at Source / Proper Shielding of Dusty Operations

Examples of pre-wetting the surface include spraying at the point of impact during hammering and using canvas sheet as shield at operation face shall be used at sites to reduce the possibility of dust pollution.

4. Regular Maintenance of Machinery

It is required to perform regular check ing and ma in ta in ing o f machinery to ensure that they are all in good working conditions at all times.

Mosquito Control

Important aspects that need to consider when performing the assessment include:

1. Effective Vector Control Plan

The dividing of the site into a maximum of 7 zones to facilitate search and destroy task is preferred. It must also be ensured that there is no sign of ground depressions, especially in areas that are under the shade or areas of sites that are seldom accessed.

2. Pitched Roof for All Site Containers

The use of pitched / sloping roof for all site offices; site containers; bund wall shelters shall be required. This w i l l prevent the poss ib i l i ty o f collecting rain water which is one of the conditions in which mosquito will love to breed in.

Figure 6: Inner Face of Wall is Coated with Chemical Resistant Paint

3. Bti Placed in Stagnating Water that Cannot be Cleared

A good site will not only use oiling (ant i -mosqui to oi l ) method to prevent mosquitoes from breeding, but wil l also use Bti / larvicide (normally used in retention tank). The dosage and the t ime o f application must be documented to estimate the time for replacement.

4. Effective Housekeeping

A site with an effective housekeeping wil l be free from water bearing receptacles with neatly stored materials. Materials shall be stored at least 60cm above ground to facilitate the oiling process.

5. Ovitraps / Gravitraps Used on Site for Monitoring of Potential Mosquitoes Breeding

A good site will use an ovitrap to test the presence of any mosquitoes. Hence, a prerequisite for the use of the ovitrap is that the housekeeping of the site must be good before it can be deployed.

The ovitrap used must be placed on levelled ground and maintained regularly.

6. Effective Drainage of Stagnating water

Any stagnated water at excavation area must be effectively drained to a holding area (sump pit) and pumped out to be treated by the water treatment plant (chemical / membrane) before discharge.

Conclusion

This article provides a guide for the project team on site to assess their contractor’senvironmental management and the areas to improve for each environmental aspect.At the same time, it will enhance environ-mental awareness amongst contractors to ensure that all sites are effectively maintained.

Lock Yan NiEnvironmental Engineer

Safety Division

07

SA

FE

TY

NE

WS

En

han

cemen

t of C

on

tractors’ E

nviro

nm

ental, S

afety & S

ecurity (E

SS

) Assessm

ent

Integrated Supervisory Control System In Rail Transit Systems

Introduction

The Integrated Supervisory ControlSystem (ISCS), deployed within North-East Line (NEL), Circle Line (CCL) and soon Downtown Line (DTL), is a Supervisory Control And Data Acquisition (SCADA) system that has been developed to provide an integrated platform for the operations of the various Rail Transit Systems (RTS) in Singapore.

From depot to station to train operations, ISCS provides the platform where many aspects of day-to-day operations of the RTS can be performed.

Scope of Monitoring & Control

The functions available in the ISCS vary from line to line. In general, it facilitates the monitoring and control of all the essential electrical & mechanical (E&M) services and systems within RTS as listed below:

a. Power supply distribution network (22kV);b. Traction power supply to the train (750Vdc 3rd rail or 1500Vdc overhead collection system);c. Emergency Tripping for Traction Supply (ETTS) or Traction Safety Shutdown System (TSSS);d. Station Environmental Control System (ECS);e. Tunnel Ventilation System (TVS);f. Fire Protection System (FPS);g. Fire/security shutters and sump/ ejector pumps;h. Power supply system (415Vac);

Inside these centres, the following ISCS installations are deployed to allow theusers to perform their respective functions:

The various users of the ISCS aresummarised in the table below:

ISCS main component OCC DCC PSC

Central Management System (CMS)

√

Depot Control System (DCS)

√

Station Management System (SMS)

√

User OCC DCC PSC

Chief Controller √

Train Control Supervisor √

Power Supply ControlSupervisor

√ √

Maintenance Control Operator

√

Station Control Operator √

Depot Control Operator √

Station Operator √

Each user is pre-configured in ISCSto assume his/her unique role andresponsibility through access controland profile configuration.

In addition, the OCC is equipped with an Overview Display System (ODS), a matrix of video display panels tiered together to create a complete view of trains, signalling and E&M information for OCC users to monitor the latest information throughout the main line. ODS also provides an overall view for OCC users to visualise and analyse the dynamics of networked equipment or systems among others include 22kVdistribution, traction power supply and tunnel ventilation.

Key Function 1 – ATS

By hosting Automatic Train Supervision system (ATS) functionalities on it, ISCS allows users to control and monitor a fully automated and driverless train operation on the mainline and signalled areas in depot. ATS provides control of stabling, launching and withdrawal of trains, time-table planning, route setting, movement regulation, and also provides real time arrival, departure and destination infor-mation to Traveller Information System (TIS). It also controls and monitors PSD. In a nutshell, all conventional ATS functions can be performed on ISCS platform and thus reduces the need to duplicate 2 sets of user interfaces and hardware.

i. Lighting;j. Il luminated Tunnel Evacuation Signage System (ITESS);k. Lifts, escalators & passenger conveyors; andl. Communication equipment (train, station and depot based).

Like a universal remote controller, ISCS also provides the platform for the operations of the following systems:

a. Automatic Train Supervision system (ATS);b. Public Address system (PA) for trains, stations and depot;c. Travel Information System (TIS) for trains and stations;d. Video Surveillance System (VSS) for trains, stations and depot; ande. Passenger Emergency Communication (PEC) inside a train.

ISCS also acts as the gateway for all the systems mentioned above by channelling maintenance and performance data to the Maintenance Management System (MMS), where maintenance activities can be scheduled and performance data analysed.

Key Installations & Functions

ISCS installations can be found in Operation Control centre (OCC), Depot ControlCentre (DCC) and Passenger Service Centre (PSC).

Figure 1: Systems Monitored/ Controlled by ISCS

08

SA

FE

TY

NE

WS

Integ

rated S

up

ervisory C

on

trol S

ystem In

Rail Tran

sit System

s

09

SA

FE

TY

NE

WS

Integ

rated S

up

ervisory C

on

trol S

ystem In

Rail Tran

sit System

sFigure 3: Passenger Information Displays (PID) at Station

Figure 4: Video images from train-borne cameras

Figure 5: Passenger Emergency Communication (PEC)

Key Function 2 – Traction Power Supply

At the end of each day, after trains are withdrawn to the depot, OCC PowerSupply Control Operator (PSCO) will switch off all traction power supply to the 3rd rail by using ISCS. To switch off a whole line, there are a lot switches (known as switchgears). ISCS’ Group Remote Control (GRC) feature allows user to simply click a few buttons and the mass switching off will be taken care of. Once switched off, various maintenance parties will commence their respective possession and works on the track. Before the trains are scheduled to resume running, the OCC operator will switch on the traction power for whole line using ISCS GRC feature.

Key Function 3 – Tunnel ventilation

When the train is stalled in the tunnel, the temperature around the train will rise. Such an occurrence will be transmitted to the ISCS and the user will be prompted to turn on the tunnel ventilation to remove the excess heat. In the event a fire breaks out inside the tunnel, ISCS will also prompt the operator to turn on the tunnel ventilation to extract the heat and smoke.

Key Function 4 – PA / TIS / VSS / PEC

The ISCS-PA module is responsible for the status monitoring, configuration, and use of the PA system to broadcastpre-recorded messages, live announcements and music through speakers at stations, depot and trains. These audio outputs can be broadcasted to selected stations/depot, PA zones and selected trains.

Conclusion

Due to the crucial roles and capabilities that ISCS provides, i t is of utmostimportance to design and deliver a highly reliable ISCS. Single point failure has been removed by introducing a redundant-system architecture for critical components. This ensures that ISCS continues to be available in facilitating the day-to-dayoperations of RTS.

ISCS has evolved from basic monitoring and controlling of E&M equipment in NS/EW lines to seamless integration withsophisticated ATS and Communication system from NEL onward. Its role has since become more critical with the debut of Singapore’s first driverless MRT train operations at NEL.

The ISCS-TIS module allows the creation, selection and sending of text messages to individual or all Passenger Information Displays (PID) at the stations.

The ISCS-PEC module connects OCC with the passenger when he/she presses the PEC button (Passenger Emergency Communication) near the train door. ISCS is able to display the “Caller ID” of the activated PEC in terms of which train and car of the activated PEC.

The ISCS-VSS module assigns the video sources from station cameras and train cameras to the video displays at various video monitors, OCC wall monitors and the ODS. Once assigned, users can view, record and playback the video received, control the playback and activate/deactivate VSS broadcasts.

Figure 2: Launching GRC from Multi-Function Terminal (MFT)

Tan Yong PeowDeputy Manager

Signals, Communications & Control Division

Ho Lee Min Assistant Manager

Signals, Communications & Control Division

Managing Pedestrian Safety At Signalised Junctions

Introduction

In 2008, pedestrian fatalities account for about 28%* of the overall road fatalities and they are the 2nd most vulnerable group of road users after motorcyclists/pillion riders.

Of all the pedestrian accidents, about 18% occurred at signalised junctions. Approximately one in three accidents involves aturning vehicle hitting a pedestrian. The distribution between right turning and left turning accidents is approximately 80% and 20% respectively. Hence, right turning movements present challenges to motorists, as well as posing safety concerns to the pedestrians crossing at a signalised junction. Therefore, countermeasures implemented by LTA for the enhancement of both pedestrians and motorists safety will be presented and discussed.

*Source of all accident statistics is from Traffic Police

The Concern at Signalised Junctions

In Singapore, the conventional signal phasing at junctions per-mits motorists to make ‘filter’ right turns during the circular green light, before the green arrow appears. In the phase where the green arrow has yet to appear, motorists would have to ensure that there are no vehicles in the opposite straight traffic stream before turning right (see Figure 1 & 2). Simultaneously, they have to look at the traffic signals as well as looking out for pe-destrians who are crossing in their turning path.

Measures Implemented at Signalised Junctions

In order to help motorists, there are various measures/tools in place to balance the need to ensure the safety of pedestrians crossing at signalised junctions and to maintain traffic flowefficiency. The measures to reduce conflicts between rightturning traffic and pedestrians can be divided into two main groups, namely warning devices/signs/markings and modified traffic signal arrangement which are shown in the next page.

Motorists are sometimes found to overly concentrate on seizing opportunities which enable them to turn upon available gaps in the opposite traffic stream, so much so that they may fail to notice, and give way to pedestrians. Research has shown that when a motorist is overwhelmed and faced with too manydecisions to make, the likelihood of an accident to occur is greater.

Figure 1: Motorist A can only make a ‘filter’ right turn when there are no oncoming vehicles in the opposing traffic flow

Figure 2: The green arrow appears, which allows motorist A to turn right freely

10

SA

FE

TY

NE

WS

Man

agin

g P

edestrian

Safety A

t Sig

nalised

Jun

ction

s

• Usedatsignalisedjunctionswhere turning motorists do not wait at appropriate positions within the junction.

• Toguidemotoristswheretostopand wait for gaps and also remind them to give way to pedestrians crossing before turning.

Turning Pockets

Group 1 – Warning Devices/Signs/MarkingsWarning devices/signs/markings are used where it is intended to provide guidance to motorists. It should not be used everywhere such that it loses its effectiveness.

When To Apply Expected BenefitTypes of Measures

• Whenthereisevidenceofconsistent behaviour of motorists not giving way to pedestrians.• Frequentvehicle-pedestrian collisions.

• Increasesmotorists’awarenessthat pedestrians are crossing alongside.• Increasestheconspicuousnessof pedestrians.

Intelligent Road Studs

• Introducedatcrossingswherethere is heavy pedestrian volume or when interacting traffic flow is heavy.

• Informspedestriansontheamountof time left to cross.• Discouragingpedestrianstosteponto the road if they feel there is not enough time.

Integrated PedestrianCountdown Timer

• Observationsthatright-turning motorists are not giving way to crossing pedestrians.

• Slowsdownright-turningmotorists, hence increasing their reaction time.

Pedestrian Refuge

Types of Countermeasures Implemented

11

SA

FE

TY

NE

WS

Man

agin

g P

edestrian

Safety A

t Sig

nalised

Jun

ction

s

Managing Pedestrian Safety At Signalised Junctions (cont’d)

• Forwidejunctionswherebothtraffic and pedestrian flows are heavy and there is space at the centre median for creating a holding area for pedestrians.

• Pedestrianmovementisforbidden when right turn traffic is released, hence virtually eliminating vehicle- pedestrian conflicts.

Staggered PedestrianCrossing

Group 2 – Modified Traffic Signal ArrangementThis step is usually carried out after Group 1 measures are being explored and when there is a serious safety concern.

When To Apply Expected BenefitTypes of Measures

• Introducedwhenthereisasafetyconcern with right turn against through traffic movements due to junction geometry.

• Reduced“rightturnagainstthrough traffic” collisions.• Conflictsbetweenrightturntrafficand pedestrians are indirectly removed.

Controlled Right Turn (eg. Red, Amber & Green, RAG)

Koh Puay PingExecutive Engineer

Road Safety Engineering (RSEU)

Sheryl TanNTU Industrial Attachment Student

Road Safety Engineering (RSEU)

Conclusion

The measures appended in the two tables have summarised some of the ways used to further enhance pedestrian safety at signalised junctions. LTA will continue to explore and implement measures to ensure safety of pedestrians crossing at signalised junctions.

12

SA

FE

TY

NE

WS

Man

agin

g P

edestrian

Safety A

t Sig

nalised

Jun

ction

s

13

SA

FE

TY

NE

WS

Accid

ent S

tatistics

* Based on Workplace Safety and Healthy Act Requirements

2009 Accident Statistics*CUMULATIVE ACCIDENT FREQUENCY RATE

(AFR)

0.7 0.8 0.8 0.9 0.9

0

1

2

3

4

JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC

AFR

LTA ACTUAL 1.33 - LTA TARGET 2.9 - 2008 INDUSTRY FIGURE

CUMULATIVE SEVERITY RATE(SR)

1110 12 9 120

100

200

JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC

SR

LTA ACTUAL 31 - LTA TARGET 221 - 2008 INDUSTRY FIGURE

CUMULATIVE FREQUENCY - SEVERITY INDEX(FSI)

0.08 0.10 0.09 0.09 0.100.0

0.5

1.0

JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC

FSI

LTA ACTUAL 0.2 - LTA TARGET 0.80 - 2008 INDUSTRY FIGURE

2009 Accident Statistics*

*Based on Workplace Safety and Health Act Requirements

0.20 - LTA TARGET

Editorial PageIn March 2009, LTA engaged Dupont Safety Resources to conduct an independent assessment of its OSHMS and benchmarking its safety performances against the best practices of organisations in the construction industry worldwide, typically for land transport infrastructure developers. Do look out for the audit findings in the next issue of the newsletter.

Group photo with DuPont Safety Resources and LTA management at the closing meeting

DuPont’s auditor, Mr James O. Faulk during his round of audit at ER198

Leading Safety in a Downturn

As the global economy slows, companies across industry are faced with sobering new economic realities. Many organizations are being forced to rethink how they conduct every aspect of their day-to-day business—including how they manage safety & health performance.

An article, “Leading Safety in a Downturn” by Dr. Tom Krause, Ph.D., Don Groover, CIH, CSP, Sarah Smith and Theodore Apking, Ph.D., helps understand the risks and opportunities that a downturn poses to safety performance, and outlines five critical actions that leaders can take to drive safety in times of economic uncertainly. These five actions include:

1. Open up, be honest and forthcoming, and communicate why safety matters now; 2. Consider the effects of your actions on the culture; 3. Refine your strategy; 4. Work the fundamentals; and 5. Demonstrate and develop transformational leadership.

For more details, please log on to www.bstsolutions.com/perspectives/article.php?item=8

New Singapore Standards

SPRING Singapore has published 2 new Singapore Standards. They are:• SS541onRestraintBelts;and• SS508Parts2&4onGraphicalSymbols-SafetyColours and Safety Sign.

Advisor Corporate Safety Committee

EditorPatrick Lee Cheng Chuen

Circulation OfficerTan Chee Lang

WritersHo Lee Min, Koh Puay Ping, Leong Choong Yiok,Lock Yan Ni, Sheryl Tan,Tan Yong Peow

Contributions or feedback to:

Land Transport Authority Safety Division251NorthBridgeRoad,Singapore179102Tel: (65) 6332 6139 Fax: (65) 63326129Email address: cheng_chuen_lee@lta.gov.sgSafety News is also available online at http://internet -stg.lta.gov.sg/projects/index_proj_safety.htm

For more details, interested parties can purchase the publications from SPRING Singapore.

21st Safety Workshop

On 18th May 2009, about 150 staff attended the Safety Workshop at our HSO auditorium. This event has served as a regularforum for our project teams to share the technical / practical experiences and challenges faced by them in the safedelivery of their projects. It also provides a platform for LTA senior management to interact with the site staff.

Three topics were presented namely:

“MarinaBarrage -CreatingaReservoir in theCity” byMrDaveToh,SeniorManagerofPUB.

“BestPracticesinManagingTrafficandConstructionSafetyatCTEWideningProject (BetweenAngMoKioAve 1 toAve 3)” by Mr See Toh Heng Fatt, PrincipalEngineering Officer for ER 213.

“Safety Considerations for the Top-Down Construction ofBayfrontStation”byMrChewLeongHo,ProjectManagerforC906.

Safety Tan says…Good housekeeping and safepractices can prevent accidentsand enhance productivity. It alsoreflects management’s commitment to safety.

Editorial Committee