score/mountain fold line glue tab score/mountain fold glue tabs & lower tower cap....
TRANSCRIPT
Score/Mountain Fold line
Score/Mountain Fold line
Glue Tab
Score/Mountain Fold glue tabs & lower tower cap.
Score/Mountain Fold glue tabs & upper tower cap.
PRINT ON CARDSTOCK
Launch Umbilical Tower
© 2005 Drawn by Michael BurkeThis cardmodel is only for personal and not commercial use.
Lightning RodRoll into tube
Crane KeelSandwich and glue both halves around cardstock
Inner SleeveCentering Circle
Top
Bottom
25 TON 10 TON
10 TON 25 TON
Score/Mountain Fold Lines
Score/Mountain Fold Lines
Trim this piece to fit
Glue Tab
Glue Tab
COLBY CRANESEATTLE
COLBY CRANESEATTLE
Mountain Fold/Score lines
Score/MountainFold line
Glue Tab
Mountain foldall triangularglue tabs on both ends
RearFront
Machinery House
As the Crane is designed to rotate, the builder may wish to build it from cardstock for extra strength. You need
build only one crane – these are alternate parts
Print on Cardstock
Denote Mountain Fold/Score Lines
Glue TabScore and Mountain Fold along dark gray line at base of tower
Glue TabScore and Mountain Fold along dark gray line at base of tower
Glue TabScore and Mountain Fold along dark gray
line at base of tower
Tower Base
Glue Tab
Glue Tabs
Glue Tab
© 2005 Drawn by Michael BurkeThis cardmodel is only for personal
and not commercial use.
Hold-Down Arm SupportsThese are wedge-shaped pieces that are glued to
the underside of the square protrusions in the top opening of the thrust
chamber and to the face of the thrust chamber liner.
All folds are Mountain folds.
Hold Down Arm Supports
Hold Down Arms
Thrust Chamber LinerCenter in holes cut out of launcher platform, between upper and lower decks.
Valley Fold/Score Lines
Glue Tabs
PRINT ON CARDSTOCK
See Crane Parts Page for Hold Down Arms and
Launcher Pedestals
Mountain Fold/Score
Lines
Circles on underside of platform are for locating holes for tower pedestals. After platform is complete, carefully drill holes with tip of X-Acto knife. Insert pedestal tubes all the way to the underside of the top of the platform deck.
1SIDE 3
1SIDE 3
1SIDE 1
1SIDE 1
1SID
E 2
1SID
E 2 1
SID
E 4
1S
IDE
4
Carefully Cut out White Portion
Carefully Cut out White Portion
© 2005 Drawn by Michael BurkeThis cardmodel is only for personal
and not commercial use.
SM ArmGlue Tab
Score/Fold lines
Glue Tab
S-IVB Arms
Forward Arm Aft ArmGlue TabGlue Tab
Score/Fold lines
Score/Fold lines
Glue Tab
CM Access Arm
Carefully cut this
white notch out
Carefully cut this white
section out
Score/Fold Lines
Score/FoldLines
Glue Tab
Score/Fold line
Glue Tab
Glue Tab
Service Arms
Damper Arm
Glue Tab Glue Tab
Score/Fold lines
Score/Fold lines
When completed, the Damper arm assembly goes together like this.
Solid red sections are the walkway (bottom) of the arm – gray section with diagonal cross members are the tops. Sides have diagonal cross members with “mesh” on bottom half.
Both ends are “capped” for rigidity and for mounting to the tower.
All folds are “mountain” folds.
Recommend printing on bond paper.PRINT TO BOND PAPER
When CM Access Arm is complete,from the top, it should be shaped like and mounted to side of tower, like this.
Other arms are mounted to front of tower, like this. (See drawing for placement.)
S-II IntermediateArm
Glue Tab
Glue Tab
S-I & SII Arms
S-II Forward
S-II Aft
S-IC Forward
S-IC Intertank
Score/Fold lines
Glue Tab
Score/Fold lines
Score/Fold lines
Score/Fold lines
Glue Tab Glue Tab
Score/Fold lines
Glue Tab
Glue Tab
Glue Tab
S-II IntermediateArm
Glue Tab
Glue Tab
S-I & SII Arms
S-II Forward
S-II Aft
S-IC Forward
S-IC Intertank
Score/Fold lines
Glue Tab
Score/Fold lines
Score/Fold lines
Score/Fold lines
Glue Tab Glue Tab
Score/Fold lines
Glue Tab
Glue Tab
Glue Tab
© 2005 Drawn by Michael BurkeThis cardmodel is only for personal
and not commercial use.
Inner Sleeve – on bottom of crane
Roll into double layered tube – Glue edge to centerline
Glue tube to bottom of Crane Keel, centered in
small circle. Inner Sleeve should fit snugly enough inside Outer Sleeve that
Crane doesn’t wobble, but loosely enough to allow
rotation.
Outer Sleeve – Inside top of Tower
Roll into double layered tube – Glue edge to centerline.
Cut out small circle on top of tower, glue tube in line with hole in order to stabilize
crane and allow it to rotate.
Lightning RodRoll into tube
Launcher Base PedestalsRoll into double layered tubes – Glue edge to centerline
Crane KeelSandwich and glue both halves around cardstock
Inner SleeveCentering Circle
Top
Bottom
25 TON 10 TON
10 TON 25 TON
Score/Mountain Fold Lines
Score/Mountain Fold Lines
Trim this piece to fit
Glue Tab
Glue Tab
Inner Sleeve
Tower
Outer Sleeve
Lightning Rod
PRINT TO BOND BAPER
Crane Boom
COLBY CRANESEATTLE
COLBY CRANESEATTLE
Mountain Fold/Score lines
Score/MountainFold line
Glue Tab
Mountain foldall triangularglue tabs on both ends
RearFront
Machinery House
As the Crane is designed to rotate, the builder may wish to
build it from cardstock for extra strength. You need build only one crane – either these parts or those on the Tower
Base page
Hold Down Arms
Glue to square protrusions in
thrust chamber opening on top of
launcher platform. Cut out bottom bulkhead of Saturn V, glue to cardstock, and use to align Hold Down Arms such
that they are centered and support the
rocket model.
All lines are Score/Mountain Fold
Lines
© 2005 Drawn by Michael BurkeThis cardmodel is only for personal
and not commercial use.
Interstage
SM/LM Adapter
Fins – Trim off Root Tabs
USA
USA
USA
USA
UNITED
STATES
UNITED
STATES
UNITED
STATES
UNITED
STATES
Roll Into double-layered tubesLaunch Escape
TowerRoll Into Cylinder
Service Module
Command Module
S-IVB
S-IC, Interstage, & S-II PRINT TO BOND BAPER
F-1 Engines
This wedge is a glue
tabEngine Fairings
Saturn V Rear BulkheadGlue to cardstock and use to align and center Hold Down Arms on Launcher Base.
Glue to Cardstock
Centering RingsGlue one in front and back of
S-1C/S-II Tube
S-IVB Centering RingsGlue Rings to Cardstock and
glue one in frontand one in back
of S-IVB
© 2005 Drawn by Michael BurkeThis cardmodel is only for personal
and not commercial use.
Damper Arm