sdb120 6mm sliding shower door v04.02.2019 · 2 assembly instructions - drawing pack i.d e b e e e...
TRANSCRIPT
Decide which hand is required. Right hand opening illustrated.
Change the hand by turning the door upside down.
Refer To Sheet 10 For Relevant Product Codes
VictoriaPlum.com0344 804 48 48
6mm SLIDING SHOWER DOOR
1
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Additional Notes
Please inspect this product upon delivery, any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage or defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note: Aluminium is a soft metal, and undergoes a series of extrusion,
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Mallet
Silicone Sealant
PZ1
2
ASSEMBLY INSTRUCTIONS - DRAWING
PACK I.D
E
B
E
E
E
B
B
B
E
PACK I.D
E
C
C
C
DAA
E
BE
EE
(9) 1x Plastic Water Deflector B
(8) 1x Plastic Water Deflector A
(4) 12x Screws 4x12 (6 For Side Panel)
(1) 6x Wall Plugs
(16) 1x Upright Magnet Profile
(2) 2x Wall Profiles
(17) 1x Magnet Seal
(19) 1x Handle(18) 1x Moving Panel
(12) 1x Bottom Profile
(7) 1x Fixed Panel
(5) 18x Screw Cover Clips (6 For Side Panel)
(13) 2x Glass Clips
(20) 2x Top Double Rollers
(6) 6x Screws 4x30
(15) 2x Bottom Double Rollers
(21) 1x Top Profile
(3 18x Screw Cover Caps (6 For Side Panel))
(10) 8x Screws 3.5x30
(14) 2x Screws 4x10
(11) 1x Fixed Panel Bottom Seal
( 1)
( 17)
(9)
(3)
( 19)
( 11)
(5)
(21)
( 13)
(7)
( 15)
(2)
( 18)
( 10)
(4)
(20)
( 12)
(6)
( 14)
(8)
( 16)
NB: ALL MEASUREMENTS + COMPONENT SIZES QUOTED ARE IN MM.
THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber .
FITTED SLIDING DOOR DRAWING
Installation Steps
3
120030 30
These Instructions show how to install a Sliding Door into a Recess. For Installation into a corner with a Side Panel – refer to the Side Panel Instructions for the relevant installation steps.
THESE INSTRUCTIONS REFER TO FITTING THIS DOOR IN A RECESS. FOR INSTALLATION IN A CORNER, USE THE STEPS SHOWN IN THE SIDE PANEL INSTRUCTIONS.
4
STEP CHECK BOX CONTENTS ARE CORRECT AND THEN MEASURE KEY COMPONENTS.1
STEP 2 DRAWING TO SHOW CORRECT SHOWER TRAY INSTALLATION
WALL
TILE OR WETWALL PANEL
SHOWER TRAY
YES
WALL
TILE OR WETWALL PANEL
SHOWER TRAY
NO
STEP 3 TRAY TO BE LEVEL
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THISSHOWER PANEL / DOOR, AND THAT SILICONE IS APPLIED ON ALL SIDES WHERE THETRAY MEETS THE TILES / WET WALL PANELS.
Measurement Matrix (before assembly) Dimension in mm
Units supplied loose for self assembly
Top / Bottom horizontal profiles
Moving panel glass
Wall profiles
Upright magnet profile
SDB120
Flat fixed panel glass(including fixed panel profiles if attached)
1048
568x1834x6
514x1780x6
1850x44
1850x46
STEP 4 ASSEMBLE FRAME AND FIXED PANEL
STEP 5 MARK WALL FIXING POSITIONS OF FIXED PANEL SIDE, DRILL WALL PROFILE OF FIXED
5
Take Care Not To Damage Wall Surface
x31
6mm
x32
x33
M4X30
x34
M4X10
M4X10
M3.5X30
M3.5X30 M3.5X30
PANEL SIDE TO THE WALL
M3.5X30
STEP 6 SLIDE WALL PROFILE OF MOVING PANEL SIDE ONTO THE FRAME
STEP 7 LIFT THE FRAME ONTO THE TRAY AND MARK WALL PROFILE POSITIONS OF
6
MOVING PANEL SIDE
STEP 8 LIFT THE FRAME OFF THE TRAY AND DRILL THE WALL
STEP 9 FITTING THE WALL PROFILE
7
6mm
x3
Take Care Not To Damage Wall Surface
Adjust the door so to be centralbetween the wall profiles .
View from outside
View from inside
M4X30x3
x3
x3
STEP 10 SECURING THE VERTICAL PROFILES
STEP 11 FITTING THE TOP AND BOTTOM ROLLERS TO THE MOVING PANEL, AND ATTACHING
8
How to adjust the width of the
sliding door
Minimum 10mm internal overlap required
Glass panel
Glass panel
Vertical profile
Vertical profile
Wall profile
Wall profile
Wall
Wall
Maximum adjustment
Minimum adjustment
Take care not to drill into the glass.
x63mm1
x6M4X122
x63
1 x23 x2 2 x2
Use a spirit level to make sure the door is square within the frame.
THE MOVING PANEL TO THE FRAME
1 x2
2 x2
3 x2
STEP 12 INSTALLING VERTICAL SEALS, AND FITTING HANDLE
STEP 13 SILICONE THE OUTSIDE EDGES
9
Silicone ( outside edge only)where the
horizontal profile meets the tray
vertical profiles meet the wall , and the
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact our customer services quoting
the following:
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
Product name: 6mm Sliding Shower Door
Product code: SDB120
Customer help line number:0344 804 48 48
10
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.
V05/09/2019
Victoria Plum Limited, Bridgehead Business Hessle, HU13 0DG
Park
13/14/16
EN 14428:2004+A1:2008
DOP No.:2013102/2014612/J160318001-1
Shower enclosures with aluminiumprofiles and safety glass
Essentialcharacteristics
Performance Harmonisedtechnical
specificationCleanability
Impactresistance/shatter
properties
Pass
Pass
PassDurability
Clause 4.2 of EN14428:2004+A1:
2008Clause 4.3 of EN14428:2004+A1:
2008Clause 4.4 of EN14428:2004+A1:
2008