sdc e300 instruction manual

3580 Willow Lane, Westlake Village, CA 91361-4921

(805) 494-0622 Fax: (805) 494-8861

www.sdcsecurity.com E-mail: [email protected]

The E6200 Series magnetic lock is mounted to the underside of the header, on the stop side of the door.

P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E6200.vsd REV - 07-10 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email [email protected]

INSTALLATION INSTRUCTIONS

E6200 SERIES MAGNETIC LOCK

Electrical Instructions:

Use properly fused U. L. Listed Power Supply

Do not install a diode in parallel with any magnetic lock. A diode

will cause a delay when releasing the door and residual magnetism

to occur.

Although SDC recommends the use of a DC power supply, a

transformer with an adjacent mounted full wave bridge rectifier

may be used. A significant drop will occur when using a full wave

bridge rectifier.

Any low voltage condition will cause erratic operation of the

optional board sensor.

When using a full wave bridge rectifier all access controls and/or

release contacts must be located between the EMlock and rectifier

to ensure quick release.

Electrical Specifications:

Dual Voltage 12 or 24VDC

Power Consumption .250mA@12VDC

.125mA@24VDC

DS Door Status Sensor SPDT, 500mA@30VDC

LS Lock Status Sensor SPDT, 2A@30VDC

Mounting Screws

Armature

Frame

Outswing


1. Fold template as indicated on dotted line. For single doors locate template against the door and header on the

lock jamb side of the frame.

2. Mark and drill holes as indicated by the template.

3. Mount armature to door.

STEPS 1 & 2

STEP 3

N/C

N/O

COM

YEL

GRN

ORG

COMMON

GOOD BOND

NO/POOR BOND

WIRE

COLORCONTACT DESCRIPTION

BOND SENSOR (BAS) WIRING

To Properly

Fused DC Power

source (-)

(+)* ACCESS CONTROL(S)

E6200 EMLOCKBLUBLKBRN

RED(+)

(-)

24VDC @ .125 Amps

To Properly

Fused DC Power

source (-)

(+)* ACCESS CONTROL(S)

E6200 EMLOCKBLU

BRNBLK

RED(+)

(-)

12VDC @ .250 Amps

24VDC CONFIGURATION

12VDC CONFIGURATION

N/C

N/O

COM

WHT

GRY

VIO

COMMON

ACTIVATE WHEN DOOR

OPEN

ACTIVATE WHEN DOOR

CLOSED

WIRE

COLORCONTACT DESCRIPTION

DOOR POSITION SENSOR (DPS) WIRING

4. WIRING DETAILS:


5. Install magnet onto the header with the magnetic face towards the door side of the stop.

Assure that the magnet and armature line up properly, then tighten down ALL mounting screws.

STEP 5

6. Test operation. When all is operating properly, install anti-

tamper plugs over socket head screws using a soft hammer

to avoid damage to the housing.


7.20

(182.88)

.375

(9.525)

4.00

(101.60)

MODEL E6200

#1/4-20 x 2

.50

(12.70)

.75

(19.05) 1.84

(46.74) 2.875

(73.03)

2.25

(67.15)

2.25

(67.15)

6.00

(152.40)

2.75

(69.85).64

(16.26)

8.00

(203.20)

1.00

(25.40)

CL

801 Avenida Acaso, Camarillo, Ca. 93012

(805) 494-0622 Fax: (805) 494-8861


P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E1200.vsd REV A1 04-11 Page 1










to occur.




bridge rectifier.




release contacts must be located between the EMlock and rectifier




Power Consumption .500mA@12VDC

250mA@24VDC



Outswing

Quick Mount

Interlocking

Mounting Assembly

Mounting Screws

Armature

Interlocking

Mounting Plate

Frame


1. Inspect the frame header to determine if mounting accessories are required (refer to page 4).





STEP 4

STEPS 2 & 3

5. Install magnet onto the header with the magnetic stripes towards the door side of the stop.

Assure that the magnet and armature line up properly, then tighten down ALL mounting screws.

STEP 5

HOLLOW METAL DOOR

From Sexnut side of door, drill exactly 1/2 hole thru one metal

thickness only. From Armature side of door, drill 5/8 hole to insert

reinforcement tube. Press in sexnut and reinforcement tube all the

way and mount armature to door using hardware provided.

REINFORCEMENT

TUBE1-3/4 HOLLOWMETAL DOOR

5/8 DRILL

STEEL WASHER 2X

RUBBER WASHER

5/16-18 SOC HD

SCREW

WITH 3/16 (5MM) ALLEN HEX

ARMATURE1/2 DRILL

SEXNUT


6. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the

door. Tap with a soft hammer to ensure proper alignment and engagement.

CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head

screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the

threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing

STEP 6

7. Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock.

A/C

MAINS

POWER

SUPPLY

12VDC

or

24VDC

SWITCH or

ACCESS

CONTROL

+

-

8. Test operation. When all is operating properly, tighten

all screws as shown. Install security pins and screws

as shown. Install anti-tamper plugs over socket head

screws using a soft hammer to avoid damage to the housing.

ATTACH THE RED SIDE OF THE CONNECTOR HERE

FOR A GREEN LED ENERGIZED & SECURE (RED=ENERGIZED & UNSECURE)

ATTACH THE GREEN SIDE OF THE CONNECTOR HERE

FOR A RED LED ENERGIZED AND UNSECURE (GREEN=ENERGIZED & SECURE)

COMNC

NO

Door Position Sensor (Reed switch)

RED (open with door closed)

GREEN (closed with door closed)

BLACK

RGBW

GBR

Door

Position

Sensor

Lock

Status

Switch

(Relay)

Power

Supply

Voltage Jumper

8NC

7C

6NO

5NC4C

3NO

2-

1+

12VDC 24VDC

LEDRED

GRN


To maintain surface plating from corrosion:Do not touch the lock face with your hands.

Clean lock face with Scotch-Brite pad by 3M (do not use

sandpaper).

Apply a thin film of rust inhibitor (LPS-3) on lock face.

Repeat application on armature plate.

Supplied Mounting Hardware

ANGLE BRACKET

E12L

Inches: 10.5" L x 0.5" H x 0.75" D

mm: 266 L x 12.7 H x 19 D

ADJUSTABLE ANGLE BRACKET

E12A

For use with Model E1200 Series

STOP FILLER PLATE

EF02

Inches: 10.5" L x 0.5" H x 0.75" D

mm: 266 L x 12.7 H x 19 D

GLASS DOOR ARMATURE BRACKET

E12U


Field adjustable for glass thickness

TOP JAMB MOUNTING BRACKET

E12Z


MOUNTING ACCESSORIES:

801 Avenida Acaso, Camarillo, Ca. 93012

(805) 494-0622 Fax: (805) 494-8861


The E600 Series magnetic lock is mounted to the underside of the header, on the stop side of the

door. An inswing mounting kit (optional) can be used when mounting on the hinge side of the

door.







Outswing





to occur.




bridge rectifier.




release contacts must be located between the magnetic lock and rectifier




Power Consumption 500mA@12VDC

250mA@24VDC



Quick Mount

Interlocking

Mounting Assembly

Mounting Screws

Armature

Interlocking

Mounting Plate

Frame


1. Inspect the frame header to determine if mounting accessories are required (refer to page 4).





STEP 4

STEPS 2 & 3

STEP 5

5. Install mounting plate to header with the interlock detail away from the door side of the stop.

Loosely fasten screws through adjustment slot as shown. Assure that the mounting plate and

armature line up properly, then tighten down ALL mounting screws.

HOLLOW METAL DOOR

From Sexnut side of door, drill exactly 1/2 hole thru one metal

thickness only. From Armature side of door, drill 5/8 hole to insert

reinforcement tube. Press in sexnut and reinforcement tube all the

way and mount armature to door using hardware provided.

REINFORCEMENTTUBE

1-3/4 HOLLOW

METAL DOOR

5/8 DRILL

STEEL WASHER 2X

RUBBER WASHER

5/16-18 SOC HD

SCREW

WITH 3/16 (5MM)

ALLEN HEX

ARMATURE1/2 DRILL

SEXNUT


7. Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock.

STEP 6

A/C

MAINS

POWER

SUPPLY

12VDC

or

24VDC

+

-SWITCH or ACCESS CONTROL

8. Test operation. When all is operating properly, tighten

all screws as shown. Install anti-tamper plugs over socket head


6. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the

door. Tap with a soft hammer to ensure proper alignment and engagement.




COMNC

NO

Door Position Sensor (Reed switch)

RED (open with door closed)

GREEN (closed with door closed)BLACK

+-NO

CNC

12

34

5

Power

Supply Lock Status

Switch

Voltage Jumper 12VDC24VDC

A RED LED INDICATES

ENERGIZED & UNSECURED

(GREEN=ENERGIZED & SECURE)

LED


To maintain surface plating from corrosion:Do not touch the lock face with your hands.

Clean lock face with Scotch-Brite pad by 3M (do not use sandpaper).

Apply a thin film of rust inhibitor (LPS-3) on lock face.

Repeat application on armature plate.

Supplied Mounting Hardware

ANGLE BRACKET

E12L

Inches: 10.5" L x 0.5" H x 0.75" D

mm: 266 L x 12.7 H x 19 D

May be field cut for use with E600

ADJUSTABLE ANGLE BRACKET

E6A


STOP FILLER PLATE

EF02

Inches: 10.5" L x 0.5" H x 0.75" D

mm: 266 L x 12.7 H x 19 D

May be field cut for use with E600

GLASS DOOR ARMATURE BRACKET

E6U


Field adjustable for glass thickness

TOP JAMB MOUNTING BRACKET

E6Z


MOUNTING ACCESSORIES:

The E300 Series magnetic lock is mounted to the underside of the cabinet housing

or vertically inside the cabinet.

P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E300.vsd REV A 04-11 Page 1





E300 SERIES MAGNETIC CABINET/DISPLAY CASE LOCK



Power Consumption 360mA@12VDC

180mA@24VDC

LS Lock Status Sensor SPDT, 250mA@30VDC

801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622


Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock.

A/C

MAINS

POWER

SUPPLY

12VDC

or

24VDC

+

-SWITCH or ACCESS CONTROL

Test operation. After verifying proper operation, tighten

all screws as shown. Install anti-tamper plugs over socket


+-

12

Power

Supply

Voltage Jumper 12VDC24VDC

COMNC

NO

Lock Status Switch

RED (open with power and door closed)

GREEN (closed with power and door closed)BLACK

P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E300.vsd REV A 04-11 Page 2

STEP 2MOUNT THE ARMATURE PLATE TO DOOR USING (1 )

RUBBER WASHER SANDWICHED BETWEEN (2)

STEEL WASHERS (THE RUBBER WASHER AND (2)

STEEL WASHERS ARE INSTALLED ON THE

MOUNTING BOLT BETWEEN THE ARMATURE PLATE

AND DOOR).

DRILL HOLES AS INDICATED

ON TEMPLATE.

PLACE TEMPLATE AGAINST

CABINET DOOR AND FRAME.

STEP 1FOLD TEMPLATE ALONG

DOTTED LINE.

STEP 3INSTALL THE MOUNTING PLATE

ADJUST THE MOUNTING PLATE SO THAT IT AND

THE ARMATURE FORM A RIGHT ANGLE.

INSTALL THE REMAINING MOUNTING SCREWS.

STEP 4INSTALL MAGNET TO

MOUNTING PLATE.




sdc e300 instruction manual

Documents