SECTION 09960

HIGH PERFORMANCE COATINGS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2013 - 2015 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Paints and coatings of the following types:1. Industrial coatings.2. Water-based primers for high performance coatings.3. Water-based acrylic enamel high performance coatings.4. Water-based epoxy high performance coatings.5. Water-based epoxy high performance floor coatings.6. Acrylic polyether urethane high performance coatings.7. Anti-graffiti coatings.8. Special use coatings.9. Standard-duty interior paints and coatings.10. Standard-duty exterior paints and coatings.

1.2 RELATED SECTIONS

A. Section 03300 - Cast-in-Place Concrete.

B. Section 04200 - Unit Masonry.

C. Section 05120 – Structural Steel.

D. Section 05500 - Metal Fabrications.

E. Section 06200 - Finish Carpentry.

F. Section 08110 - Custom Hollow Metal Doors and Frames.

1.3 REFERENCES

A. American Society for Testing Materials (ASTM):1. ASTM B 117 - Standard Practice for Operating Salt Spray (Fog) Apparatus.2. ASTM D 522 - Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings.3. ASTM D 523 - Standard Test Method for Specular Gloss.4. ASTM D 610 - Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces.5. ASTM D 714 - Standard Test Method for Evaluating Degree of Blistering of Paints.6. ASTM D 1308 - Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes.7. ASTM D 1654 - Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments.8. ASTM D 1735 - Standard Practice for Testing Water Resistance of Coatings

09960-1

Using Water Fog Apparatus.9. ASTM D 2370 - Standard Test Method for Tensile Properties of Organic Coatings.10. ASTM D 2486 - Standard Test Methods for Scrub Resistance of Wall Paints.11. ASTM D 2794 - Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact).12. ASTM D 2805 - Standard Test Method for Hiding Power of Paints by Reflectometry.13. ASTM D 3359 - Standard Test Methods for Measuring Adhesion by Tape Test.14. ASTM D 3363 - Standard Test Method for Film Hardness by Pencil Test.15. ASTM D 4060 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser.16. ASTM D 4587 - Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings.17. ASTM D 4828 - Standard Test Methods for Practical Washability of Organic Coatings.18. ASTM D 5894 - Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet).19. ASTM D 7073 - Standard Guide for Application and Evaluation of Brush and Roller Applied Paint Films.20. ASTM G 151 - Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources.

B. Green Seal, Inc.: GS-11 - Standard for Paints and Coatings.

C. Ozone Transmission Commission (OTC) - Established levels of Volatile Organic Compounds.

D. The Society of Protective Coatings (SSPC):1. SSPC (PM1) - Steel Structures Painting Manual, Vol. 1, Good Painting Practice; Society for Protective Coatings.2. SSPC (PM2) - Steel Structures Painting Manual, Vol. 2, Systems and Specifications; Society for Protective Coatings.

E. 40 CFR 59, Subpart D - National Volatile Organic Compound Emission Standards for Architectural Coatings; U.S. Environmental Protection Agency; current edition.

F. US Green Building Council, (USGBC) - Green Seal standards for LEED paint credits.

1.4 DEFINITIONS

A. Commercial as used in this Section refers to a product well suited for a commercial application.

B. DFT as used in this Section refers to the Dry Film Thickness of the coating.

C. Enamel refers to any acrylic or alkyd (oil) base paint which dries leaving an eggshell, pearl, satin, semi-gloss or high gloss enamel finish.

D. LEED as used in this Section refers to USGBC Leadership in Energy and Environmental Design. Products listed meet LEED criteria for environmentally safe interior primers, paints and coatings.

E. OTC as used in this Section refers to the Ozone Transmission Commission. OTC has established the following VOC levels for the Northeastern United States. Products shall meet the following OTC limits for VOC's.

1. Interior flat paints: 100 grams per liter or less, per gallon.

09960-2

2. Interior enamels: 150 grams per liter or less, per gallon.3. Interior stains: 250 grams per liter or less, per gallon.4. Interior primers: 200 grams per liter or less, per gallon.5. Rust preventive coatings: 400 grams per liter or less, per gallon.6. Dry fog coatings: 400 grams per liter or less, per gallon.7. Floor coatings: 250 grams per liter or less, per gallon.

F. VOC as used in this Section refers to Volatile Organic Compounds found in primers, paints, sealers and stains. The level of VOCs appears after each product listed in the Schedule in grams per liter (g/L).

G. Paints are available in a wide range of sheens or glosses, as measured by a gloss meter from a 60 degree angle from vertical, as a percentage of the amount of light that is reflected. The following terms are used to describe the gloss of our products.

1. Flat - Less than 5 Percent.2. Eggshell - 5 - 20 Percent.3. Satin - 20 - 35 Percent.4. Semi-Gloss - 30 - 65 Percent.5. Gloss - Over 65 Percent.

1.5 SUBMITTALS

A. Submit under provisions of Section 01 30 00 - Administrative Requirements.

B. Coordinate with Section 01 30 00 - Administrative Requirements, for submittal procedures and LEED Submittal Forms MRc3, MRc4, MRc5.

C. LEED Certification Product Data:1. See Section 01 11 13 - Work Covered by Contract Documents.2. Submittals Required:a. MRc3 Resource Reuse (LEED Form).b. MRc4 Recycled Content (LEED Form).c. MRc5 Local and Regional Materials (LEED Form).d. EQc4.1 Low Emitting Materials - Adhesives and Solvents (VOC Certification

Letter).e. EQc4.2 Low Emitting Materials - Paint (VOC Certification Letter).f. Green Seal Standard GS-11 Certified Product certificates.

D. Product Data: For each paint system indicated, including:1. Product characteristics.2. Surface preparation instructions and recommendations.3. Primer requirements and finish specification.4. Storage and handling requirements and recommendations.5. Application methods.6. Cautions for storage, handling and installation.

E. Selection Samples: Submit a complete set of color chips that represent the full range of manufacturer's color samples available.

F. Verification Samples: For each finish product specified, submit samples that represent actual product, color, and sheen.

G. Schedule: Provide a paint schedule indicating each type of surface to be painted, and primer and finish coats proposed for use; include dry film thickness for each coating.

1.6 QUALITY ASSURANCE

09960-3

A. Installer Qualifications: A firm or individual experienced in applying paints and coatings similar in material, design, and extent to those indicated for this Project, whose work has resulted in applications with a record of successful in-service performance.

B. Paint exposed surfaces. If a color of finish or a surface is not specifically mentioned, Architect will select from standard colors and finishes available.

C. Do not paint prefinished items, concealed surfaces, finished metal surfaces, operating parts, and labels unless indicated.

D. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.

1. Finish surfaces for verification of products, colors and sheens.2. Finish area designated by Architect.3. Provide samples that designate primer and finish coats.4. Do not proceed with remaining work until the Architect approves the mock-up.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Delivery: Deliver manufacturer's unopened containers to the work site. Packaging shall bear the manufacturer's name, label, and the following list of information:

1. Product name and type (description).2. Application and use instructions.3. Surface preparation.4. VOC content.5. Environmental issues.6. Batch date.7. Color number.

B. Storage: Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.

C. Store materials in an area that is within the acceptable temperature range, per manufacturer's instructions. Protect from freezing.

D. Handling: Maintain a clean, dry storage area, to prevent contamination or damage to the coatings.

1.8 PROJECT CONDITIONS

A. Maintain or anticipate environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.9 EXTRA MATERIALS

A. Furnish extra paint materials from the same production run as the materials applied and in the quantities described below. Package with protective covering for storage and identify with labels describing contents. Deliver extra materials to Owner.

B. Furnish Owner with an additional one percent of each material and color, but not less than 1 gal (3.8 l) or 1 case, as appropriate.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Rust-Oleum®, which is located at: 11 Hawthorn Pkwy. ; Vernon

09960-4

Hills, IL 60061; Toll Free Tel: 800-323-3584; Tel: 847-367-7700; Fax: 847-816-2330; Email:request info (productsupport@rustoleum.com); Web:www.rustoleum.com

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 SURFACE PREPARATION / STRUCTURAL CLEANERS

A. Interior Cleaner: 1. Rust-Oleum Industrial Pure Strength Cleaner/Degreaser 3599.2. Krud Kutter Original3. Zinsser JOMAX Virus and Mold Killer.4. Krud Kutter Pre Paint Cleaner5. Krud Kutter Must for Rust6. Krud Kutter Metal Etch7. Krud Kutter Mold & Mildew Stain Remover8. Krud Kutter Rustex9. Krud Kutter Gloss Off

B. Exterior Cleaner: 1. Rust-Oleum Industrial Pure Strength Cleaner/Degreaser 3599.2. Krud Kutter Original3. Krud Kutter Multi Purpose Wash4. Krud Kutter Concrete Clean & Etch5. Krud Kutter House Wash6. Krud Kutter Deck & Fence Wash7. Zinsser JOMAX - House Cleaner and Mildew Killer.8. Krud Kutter Concrete & Driveway Cleaner9. Krud Kutter Metal Etch10. Krud Kutter Must for Rust11. Krud Kutter Rustex12. Krud Kutter Pre Paint Cleaner13. Krud Kutter Gloss Off

2.3 INDUSTRIAL COATINGS

A. DTM Acrylic Enamel:1. Water-based acrylic enamel for industrial application. Resists mild chemical fumes and spills.2. Product: 3700 System DTM Acrylic.3. Primer: Red primer.4. Primer: Gray primer.5. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.6. Agriculture Canada (Canadian Food Inspection Agency) compliant.7. Performance:a. Pencil Hardness (Method: ASTM D 3363) Result: F.b. Conical Flexibility (Method: ASTM D 522) Result: Greater than 33 percent.c. Cyclic Prohesion (Rating 1-10, 10=best Method: ASTM D 5894, 2 Cycles, 672

hours) Result: Rating 10 per ASTM D 714 for blistering.d. Impact Resistance (direct/reverse) Method: ASTM D 2794 Result: Greater than

160.e. Taber Abrasion Method: ASTM D 4060 CS 17 wheels 500g load, 1000 cycles

Result: 42 mg loss.f. Accelerated Weathering (percent gloss retention) Method: ASTM D 4587, QUV

09960-5

Type A bulb, 450 hours Result: 87 percent retention (color-black).8. Color: Tint bases and stock colors available for custom colors. Refer to Finish Schedule

B. Industrial DTM Epoxy Mastic:1. Product: DTM Epoxy Mastic. Durable, high-performance epoxy coatings offering excellent solvent, chemical and abrasion resistance. Self priming.2. 9100 System DTM Epoxy Mastic.3. Performance:a. Pencil Hardness (Method: ASTM D 3363) Result: 4H.b. Conical Flexibility (Method: ASTM D 522) Result: Greater than 32 percent.c. Cyclic Prohesion (Rating 1-10, 10=best Method: ASTM D 5894, 2 Cycles, 2300

hours) Result: Rating 10 per ASTM D 714 for blistering, Result: Rating 10 per ASTM D 1654 for corrosion.

d. Impact Resistance (direct/reverse) Method: ASTM D 2794 Result: 160 in-lbs.e. Taber Abrasion Method: ASTM D 4060 CS 17 wheels 500g load 1000 cycles

Result: 57 mg loss.f. Gloss (60 degree) Method: ASTM D 4587 (450 hours) Result: 82 percent

(color-black), semi-gloss bases:35-55 percent, flat bases:1 0-15 percent.g. Accelerated Weathering ( percent gloss retention) Method: ASTM D 4587, QUV

Type A bulb, 450 hours Result: 92 percent retention (color-black).4. V9100 System Low VOC DTM Epoxy Mastic.5. Performance:a. Pencil Hardness (Method: ASTM D 3363) Result: 5H.b. Conical Flexibility (Method: ASTM D 522) Result: Greater than 33 percentc. Cyclic Prohesion (Rating 1-10, 10=best Method: ASTM D 5894, 2 Cycles, 3000

hours) Result: Rating 10 per ASTM D 714 for blistering, Result: Rating 10 per ASTM D 1654 for corrosion.

d. Impact Resistance (direct) Method: ASTM D 2794 Result: 132.e. Taber Abrasion Method: ASTM D 4060 CS 17 wheels 500g load 1000 cycles

Result: 125 mg loss.f. Gloss (60 degree) Method: ASTM D 4587 (450 hours) Result: 80 percent.6. SC9100 System Low VOC Epoxy Mastic.7. Topcoats: High Performance Acrylic Finishes (3700 and 3100 Systems).8. Topcoats: High Gloss Urethane Finishes (9400 System). Do not use over 9115402 Aluminum.9. Topcoats: Low VOC Urethane Finishes (9700 System). Do not use over 9115402 Aluminum.10. Topcoats: DTM Urethane Mastic Finishes (9800 System), Do not use over 9115402 Aluminum.11. Versatile epoxy system is perfect for Direct-To-Metal (DTM), direct-to-tightly adhered rust, concrete floors, pools and more. A high solids, next generation polyamine converted epoxy.12. Self-priming, single coat. Apply Direct-To-Metal and tightly adhered rust.13. 1:1 mixing ratio of base and activator.14. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.15. Agriculture Canada (Canadian Food Inspection Agency) compliant.16. Standard Activator:a. For air and surface temperature of 50 to 100 degree F (10 to 38 degree C).17. Immersion Activator:a. For fresh or salt water immersion of steel or concrete where water

temperatures do not exceed 125 degree F (52 degree C).b. For floor coating applications.c. Slightly lower gloss than standard activator.d. Not for use in potable water tanks.

09960-6

18. Low Temperature Activator:a. For air and surface temperatures of 40 to 60 degree F (5 to 15 degree C).19. Fast Cure Activator:a. Faster cure to minimize downtime.b. Recoat in 4 hours at 70 degree F (21 degree C) and 50 percent RH.c. For air and surface temperature of 50 to 100 degree F (10 to 38 degree C).d. Slightly lower gloss than standard activator.

C. DTM Urethane Mastic:1. Product: DTM Urethane Mastic 9800 System, Aliphatic polyurethane coating.

D. Elastomeric Acrylic Coating System:1. Product: Noxyde.a. Heavy-duty, water-based, elastomeric acrylic coating system that provides

corrosion protection in aggressive environments.b. Manufacturer's 10 year warranty shall be provided.c. Surface preparation - minimal.d. Flexibility - 200 percent elasticity that moves with structure and doesn't

delaminate.e. Primer and topcoat in one application.2. Color: . Color: Stock colors available. Refer to Finish Schedule3. Primer: 3202504 - 3200 System Clear Blue Undercoat.4. Primer: 202600 - Pegalink/202550 Light Gray.5. Primer: 202600 - Pegalink/202600 Primer White.6. Primer: None (self priming).7. Topcoat: 9800 System DTM Urethane Mastic.8. Topcoat: 9700 System 250 VOC Acrylic Polyester Urethane.9. Topcoat: 3700 System DTM Acrylic Enamel.10. Topcoat: 3100 System Speedy-Dry DTM Acrylic Enamel.11. Topcoat: 5200 System Industrial Choice DTM Acrylic.12. Topcoat: Sierra Performance Beyond Multi-Purpose Acrylic Enamel.13. Topcoat: Sierra Performance MetaIMax DTM Acrylic Urethane.

E. Elastomeric Acrylic Coating System:1. Product: Peganox. Utilizes similar technology as Noxyde but specifically designed to brush and roll.a. Brush or roller applied, water-based, elastomeric acrylic maintenance coating

designed for high protection, adhesion, or elasticity.b. Provides excellent long-term corrosion protection.c. Minimal surface preparation.2. Physical Characteristics:a. Resin Type: Water-based acrylic elastomeric.b. Pigment Type: Titanium dioxide, zinc phosphate.c. Solvents: Water, Ethylene Glycol.d. Solids by Weight: 58+/-3.e. Solids by Volume: 48+/-3.f. VOC: 25g/l (0.21 lbs/gal).g. Recommended DFT: 3 mils (75u). Two coats required.3. Primer: 3202504 - 3200 System Clear Blue Undercoat.4. Primer: 202600 - Pegalink/202550 Light Gray.5. Primer: 202600 - Pegalink/202600 Primer White.6. Primer: None (self priming).7. Topcoat: High Performance 3700 System DTM Acrylic Enamel.8. Topcoat: Industrial Choice 5200 System DTM Acrylic.9. Topcoat: Sierra Performance S-37 MetalMax.

09960-7

2.4 WATER-BASED PRIMERS FOR HIGH PERFORMANCE COATINGS

A. Product: Griptec Acrylic Primer. Multi-surface sandable primer.1. A water-based, acrylic primer that is ideal for general purpose priming applications.2. Provides outstanding adhesion on difficult to paint surfaces.3. Dries fast - 30 minutes to touch and tack free.4. Provides excellent stain-blocking power.5. Immediately sandable when dry.6. Tolerates pH levels up to 13.7. Meets LEED product requirements for Indoor Air Quality.8. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.9. Physical Characteristics:a. Resin Type: Acrylic.b. Pigment Type: Titanium dioxide, kaolin.c. Solvents: Water.d. Solids by Weight: 52 percent.e. Solids by Volume: 40 percent.f. VOC: 0 g/l (0.0 lbs/gal).g. Recommended DFT: 1 to 3 mils (25u to 75u).10. Performance:a. Pencil Hardness (Method: ASTM D 3363): Result: HB.b. Impact Resistance (direct Method: ASTM D 2794): Result: Greater than 100 in.-

Ibs.c. Adhesion Result: Excellent (wall bound, stucco, cement, wood, ABS plastic,

non-ferrous metal, previously painted surfaces).11. Color: 208555 - Flat Gray.12. Color: 208028 - Flat White (Tintable).13. Topcoat: Sierra Beyond Multi-Purpose Acrylic Enamel.14. Topcoat: Sierra Epoxy Acrylic Enamel.

B. Product: S70/S71 Water-based Epoxy Acrylic Primer.1. Environmental Resistance: Chemical and corrosion resistance.2. Film Integrity: Superior adhesion.3. Dry Time: 30 minutes to touch and tack free.4. Meets LEED product standards for Indoor Air Quality.5. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.6. Physical Characteristics:a. Resin Type: Epoxy.b. Pigment Type: Varies with color.c. Solvents: Water.d. Solids by Weight: 58 percent.e. Solids by Volume: 43 percent.f. VOC: 0 g/l (0.0 lbs/gal).g. Recommended DFT: 2 to 3 mils (50u to 75u).7. Performance:a. Pencil Hardness (Method: ASTM D 3363) Result: H.b. Conical Flexibility (Method: ASTM D 522) Result: 180 degree on 1/2 inch (12

mm) Mandrel.c. Impact Resistance (direct) (Method: ASTM D 2794) Result: 50 in-Ib.d. Finish Gloss Result: Flat.e. Intercoat Adhesion (Method: ASTM D 3359) Result: Excellent.f. Corrosion Resistance (Method: ASTM B 117, Salt Spray, CRS B100) Result: 4

mils < 1500 hours.

09960-8

8. Color: 208113 - Gray Spray Enamel; spray only.9. Color: 208110 - White Brush Enamel; brush/roll only.

C. Product: MetalMax DTM Acrylic Enamel.1. Direct-To-Metal (DTM), water-based, urethane modified acrylic provides excellent corrosion and humidity resistance.2. Primer Application: Provide as a primer under Beyond finishes.3. Dry Time: 30 minutes to touch and tack free.4. Finish: Excellent color retention.5. Corrosion Protection: Protects new and previously painted metal.6. Meets LEED product requirements for Indoor Air Quality.7. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.8. Physical Characteristics:a. Resin Type: Acrylic Urethane.b. Pigment Type: Varies with color.c. Solvents: Water.d. Solids by Weight: 51 percent.e. Solids by Volume: 40 percent.f. VOC: 0 g/l (0.0 lbs/gal).g. Recommended DFT: 1 to 3 mils (25u to 75u).9. Performance:a. Scrub Resistance (Method: ASTM D 2486) Result: Greater than 400 cycles.b. Washability (Method: ASTM D 4828) Result: 7.c. Conical Flexibility (Method: ASTM D 522) Result: 180 degree on 1/2 inch (12

mm) Mandrel.d. Prohesion (1 coat DTM) Rating 1-10 10-best (Method: ASTM D 5894, 1,000

hours) Result: 10 per ASTM D 714 for blisterinq, Result: 6 per ASTM D 1654 for corrosion, Result: 10 per ASTM D 610 for rusting.

e. Impact Resistance (direct) (Method: ASTM D 2794) Result: 100 Ibs.f. Gloss at 60 degree (Method: ASTM D 523) Result: 40-50 percent.g. Fade Resistance (Method: ASTM G 151, QUV Type A bulb, 1,000 hours)

Result: Delta E = 0.68.h. Crosshatch Adhesion (Method: ASTM D 3359) Result: 4B.i. Water Resistance (Method: ASTM D 1735, CRS, 7 day cure) Result: No effect

at greater than 1,000 hours.j. Hiding Power (Method: ASTM D 2805) Result: 0.99 (white).10. Color: Tint bases and stock colors available for custom colors. Refer to Finish Schedule.

2.5 WATER-BASED ACRYLIC ENAMEL HIGH PERFORMANCE COATINGS

A. Product: Beyond Acrylic Enamel.1. A water-based, urethane modified acrylic provides excellent color retention and durability.2. Dry Time: 30 minutes to touch and tack free.3. Re-Coat: Multiple coats can be applied in one day.4. Film Integrity: Superior resistance to chipping, cracking and peeling.5. Finish: Non-blocking and mar resistant.6. Meets LEED product requirements for Indoor Air Quality.7. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.8. Agriculture Canada (Canadian Food Inspection Agency) compliant.9. Physical Characteristics:a. Resin Type: Acrylic Urethane.b. Pigment Type: Varies with color.

09960-9

c. Solvents: Water.d. Solids by Weight: 50 percent.e. Solids by Volume: 36 to 38 percent.f. VOC: 0 g/l (0.0 lbs/gal).g. Recommended DFT: 1 to 3 mils (25u to 75u).10. Performance:a. Pencil Hardness (Method: ASTM D 3363) Result: B.b. Conical Flexibility (Method: ASTM D 522) Result: Greater than 33 percent.c. Cyclic Prohesion (Rating 1-10, 10=best Method: ASTM D 5894, 2 Cycles, 672

hours) Result: Rating 10 per ASTM D 714 for blistering, Result: Rating 9 per ASTM D 1654 for corrosion, Result: 10 per ASTM D 610 for rusting.

d. Impact Resistance (Method: ASTM D 2794) Result: 135 lb (direct), 152 lb (indirect).

e. Gloss at 60 Degree (Method: ASTM D 523) Result: 80 to 85 percent.f. Accelerated Weathering ( percent gloss retention) Method: ASTM D 4587, QUV

Type A bulb, 450 hours Result: 75 percent.g. Crosshatch Adhesion (Method: ASTM D 3359) Result: 5A.h. Hiding Power (Method: Pfund Cryptometer): Excellent; 2035 sf/ 0.8 wet mils.11. Color: Tint bases and stock colors available for custom colors. Refer to Finish Schedule.

2.6 WATER-BASED EPOXY HIGH PERFORMANCE COATINGS

A. Product: S60 Water-based Epoxy Maintenance Coating.1. Primer: S70/S71 Water-based Epoxy Primer.2. Environment Hazard: Zero VOCs, zero HAPs and no solvent odor.3. Durability: Frequent wash downs and cleaning4. Dry Time: 30 minutes dry to the touch, return to service in 24 hours.5. Meets LEED product requirements for Indoor Air Quality6. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.7. Agriculture Canada (Canadian Food Inspection Agency) compliant.8. Green Seal certified. Meets the Green Seal GS-11 environmental standard for volatile organic compounds (VOCs) and other ingredients.9. Physical Characteristics:a. Resin Type: 100 percent epoxy.b. Pigment Type: Varies with color.c. Solvents: Water.d. Solids by Weight: 59.5 percent.e. Solids by Volume: 50 percent.f. VOC: 0 g/l (0.0 lbs/gal).g. Recommended DFT: 2 to 3 mils (50 to 75u).10. Performance:a. Alkali Resistance (Method: ASTM D 1308) Result: No effect.b. Taber Abrasion/Abrasion Resistance (Method: ASTM D 4060 CS-17 wheel,

1000 gram load, 1000 cycles) Result: 117 mg loss.c. Gloss at 60 degree (Method D 523) Result: 80 to 85 percent.d. Applicability (Method ASTM D 7073) Result: Passed.e. Washability (Method: ASTM D 4828) Result: 9.f. Scrub Resistance (Method: ASTM D 2486) Result: Greater than 2000 cycles.g. Pencil Hardness (Method: ASTM D 3363) Result: 3H.11. Color: Tint bases and stock colors available for custom colors. Refer to Finish Schedule.

2.7 WATER-BASED EPOXY HIGH PERFORMANCE FLOOR COATINGS

09960-10

A. Product: S40 Water-Based Epoxy Floor Coating.1. Environmental Hazards: Zero VOCs, zero HAPs and no solvent odor.2. Dry Time: 30 minutes dry to the touch, return to service in 24 hours.3. Meets LEED product requirements for Indoor Air Quality.4. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.5. Agriculture Canada (Canadian Food Inspection Agency) compliant.6. Green Seal certified. Meets the Green Seal GS-11 environmental standard for volatile organic compounds (VOCs) and other ingredients7. Physical Characteristics:a. Resin Type: 100 percent epoxy.b. Pigment Type: Varies with color.c. Solvents: Water.d. Solids by Weight: 59.5 percent.e. Solids by Volume: 50 percent.f. VOC: 0 g/l (0.0 lbs/gal).g. Recommended DFT: 3.5 to 5 mils (87.5 to125u) for color finishes. 2 to 3 mils

(50 to 75u) for clear finishes.8. Performance:a. Alkali Resistance (Method: ASTM D 1308) Result: No effect.b. Impact Resistance (direct) (Method: ASTM D 2794) Result: 35 in-Ibs.c. Taber Abrasion/Abrasion Resistance (Method: ASTM D 4060 CS-17 wheel,

1000 gram load, 1000 cycles) Result: 117 mg loss.d. Gloss at 60 degree (Method D 523) Result: 80 to 85 percent.e. QUV/Epoxy Discoloration (Method ASTM G5388, 96 hours) Result: 1.5 percent

gloss loss/change, very slight yellowing.f. Concrete Adhesion (Method: ASTM D7234) Result: Greater than 200 psi -

concrete failure.g. Tensile Strength (Method: ASTM D 2370) Result: 2,755 Ib/sq. in.9. Color: Tint bases and stock colors available for custom colors. Refer to Finish Schedule.

B. Product: S42 Water-Based Epoxy Floor Coatings (Medium Build).1. Finish: Tough medium build finish that provides excellent durability.2. Chemical Resistance: Highly resistant to most chemicals and abrasion.3. Dry Time: 30 minutes to touch and tack free. Can accept light traffic in 24 hours.4. Meets LEED product requirements for Indoor Air Quality.5. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.6. Agriculture Canada (Canadian Food Inspection Agency) compliant.7. Meets the Green Seal GS-11 environmental standard for volatile organic compounds (VOCs) and other ingredients8. Color: Tint bases and stock colors available for custom colors. Refer to Finish Schedule.

2.8 ACRYLIC POLYESTER URETHANE HIGH PERFORMANCE COATINGS

A. Product: 9700 System 250 VOC Acrylic Polyester Urethane.1. Low 250 VOC, high solids, thin film, acrylic polyurethane provides corrosion protection for excellent long-term appearance in severe environments.2. Primer: V9100 System Low VOC DTM Epoxy Mastic.3. System Performance:a. System Tested: Primer: Rust-Oleum Industrial Epoxy Mastic with the #205015

Low VOC Standard Activator. Topcoat: Rust-Oleum Industrial Low VOC Urethane.

b. Pencil Hardness (Method: ASTM D 3363): Result: F.

09960-11

c. Conical Flexibility (Method: ASTM D 522); Result: Greater than 33 percent.d. Prohesion (Rating 1-10, 10=best - Method: ASTM D 5894, 3300 hours): Result:

10 per ASTM D 714 for blistering, Result: 10 per ASTM D 1654 for corrosion, Result: 10 per ASTM D 610 for rusting.

e. Impact Resistance (direct/reverse Method: ASTM D 2794): Result: greater than 160 in.-Ibs.

f. Taber Abrasion (Method: ASTM D 4060, CS-17 wheels, 1000 gram load, 1000 cycles): Result: 52 mg loss.

g. Gloss (60 degree) (Method: ASTM D 523): Result: 95 percent (color-white).h. Accelerated Weathering (percent gloss retention) (Method: ASTM D 4587, QUV

Type A bulb, 2100 Hours): Result: 100 percent (color-white).4. Color and Gloss Retention: Excellent.5. Corrosion, chemical, impact and abrasion resistance for extreme durability.6. Excellent coverage in one coat.7. Thin film application (1 to 2 mils DFT).8. Available accelerator speeds dry time.9. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.10. Primer: V9100 System Low VOC DTM Epoxy Mastic.11. Color: Tint bases and stock colors available for custom colors. Refer to Finish Schedule.

2.9 SPECIAL USE COATINGS

A. Heat Resistant Coatings:1. Product: 4200/4300 System Pure Silicone Aluminum System High Heat Coatings.2. Unmodified pure silicone protects surfaces subject to temperatures 500 degree F (649 degree C).3. Unmodified pure silicone protects surfaces subject to temperatures 800 degree F (649 degree C).4. Unmodified pure silicone protects surfaces subject to temperatures 1200 degree F (649 degree C).5. Primer: Self-priming.6. Primer: 4268 primer.7. USDA acceptable. Can be used in USDA facilities based on FSIS Directive 11,000.4 (Rev. 1), November 24, 1995.

B. Coal Tar Epoxy:1. Product: C9578 System Coal Tar Epoxy.2. Formulation: High solids converted epoxy with refined coal tar pitch for use in severe industrial or marine environments.3. Application Environment: Protects against severe abrasion, strong chemicals and non-potable water immersion.4. Self-priming, high-build coating (8-10 mils (200 to 250u) DFT.5. Complies with Corps of Engineers Specs C-200, C-200A, Steel Tank Institute Corrosion Control System STI-P3, AWWA Spec C210-84, and SSPC-Paint 16.

2.10 INTERIOR PAINT SCHEDULE

A. Concrete - Interior Floors (Dust Proofer Floor Sealer):1. Low Gloss Finish:a. Intermediate Coat: 5500 Acrylic Dustproofer Floor Sealer VOC 100.b. Finish Coat: 5500 Acrylic Dustproofer Floor Sealer VOC 100.

B. Concrete - Interior Floors Multi-Purpose:1. Gloss Finish:

09960-12

a. Finish Coat: Sierra S-40 Water-Based Gloss Concrete Epoxy Floor Coating. Recommended (DFT) 3.5-5 mils Per Coat.

2. Gloss Finish:a. Finish Coat: 5600 system acrylic urethane floor paint.3. High-Gloss Finish:a. Finish Coat: Easy Clear Two Par Epoxy Maintenance Floor Coating VOC 100

Recommended (DFT) 2-5 mils Per Coat.4. Gloss Finish:a. Finish Coat: 5600 Acrylic Urethane Floor Paint VOC 100 Recommended (DFT)

1.5-2 mils Per Coat.

C. Concrete - Interior:1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra S-60 Water Based Gloss Epoxy.c. Finish Coat: Sierra S-60 Water Based Gloss Epoxy.

D. Concrete - Interior (Ceilings):1. Flat Finish:a. Finish Coat: 5100 System Acrylic Dry Fall Coating VOC 100. Recommended

(DFT) 2-2.5mils Per Coat.

E. Drywall - Interior (Walls, Ceilings, Gypsum Board):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra S-60 Water-Based Gloss Epoxy.c. Finish Coat: Sierra S-60 Water-Based Gloss Epoxy.

F. Metal - Interior (Ceilings-Steel, Joists, Trusses, Beams, HVAC Ductwork and Pipes):1. Flat Finish:a. Finish Coat: 5100 System Acrylic Dry Fall Coating VOC 100. Recommended

(DFT) 2-2.5 mils Per Coat.

09960-13

G. Metal - Interior (Galvanized, Aluminum):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra S-60 Water-Based Gloss Epoxy.c. Finish Coat: Sierra S-60 Water-Based Gloss Epoxy.

H. Metal - Interior (Steel, Structural Steel Columns, Joists, Trusses, Beams, Miscellaneous and Ornamental Iron):

1. Satin Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra S-60 Water-Based Gloss Epoxy.c. Finish Coat: Sierra S-60 Water-Based Gloss Epoxy.5. Semi-Gloss Finish, Low VOC:a. Primer: Professional Oil Rusty Metal Primer 100 VOC.b. Intermediate Coat: Professional Oil Semi-Gloss 100 VOC.c. Finish Coat: Professional Oil Semi Gloss 100 VOC.6. Gloss Finish, Low VOC:a. Primer: Professional Oil Rusty Metal Primer 100 VOC.b. Intermediate Coat: Professional Oil Gloss 100 VOC.c. Finish Coat: Professional Oil Gloss 100 VOC.7. High Gloss, Low VOC:a. Primer: Commercial CV740 System DTM Alkyd White Primer.b. Intermediate Coat: Commercial CV740 System DTM Alkyd Gloss Enamel.c. Finish Coat: Commercial CV740 System DTM Alkyd Gloss Enamel.

I. Metal - Interior Corrosion/Rust (Ferrous Metal, Iron, Steel, Structural Steel):1. Satin Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.

09960-14

b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra S-60 Water-Based Gloss Epoxy.c. Finish Coat: Sierra S-60 Water-Based Gloss Epoxy.5. High Gloss, Low VOC:a. Primer: Commercial CV740 System DTM Alkyd Red Primer 100 VOC.b. Intermediate Coat: Commercial CV740 System DTM Alkyd Gloss Enamel 100

VOC.c. Finish Coat: Commercial CV740 System DTM Alkyd Gloss Enamel 100 VOC.

J. Plaster - Interior:1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra S-60 Water-Based Gloss Epoxy.c. Finish Coat: Sierra S-60 Water-Based Gloss Epoxy.

K. Plastic - Interior (Architectural PVC, Plastic, Fiberglass):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.

L. Wood - Interior (Ceilings):1. Flat Finish:a. Finish Coat: 5100 System Acrylic Dryfall Coating VOC 100.

M. Wood - Interior (Walls, Ceilings, Doors, Trim):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.

09960-15

c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra S-60 Water-Based Gloss Epoxy.c. Finish Coat: Sierra S-60 Water-Based Gloss Epoxy.

N. Wood - Interior (Ceilings):1. Flat Finish:a. Finish Coat: 5100 System Acrylic Dry Fall Coating VOC 100. Recommended

(DFT) 2-2.5 mils Per Coat.

2.11 EXTERIOR PAINT SCHEDULE

A. Asphalt - Exterior:1. Jet Black Finish:a. Intermediate Coat: Epoxy Shield Blacktop Coating.b. Finish Coat: Epoxy Shield Blacktop Coating.

B. Concrete - Exterior Floors (Dust Proofer Floor Sealer):1. Low Gloss Finish:a. Intermediate Coat: 5500 Acrylic Dustproofer Floor Sealer VOC 100b. Finish Coat: 5500 Acrylic Dustproofer Floor Sealer VOC 100

C. Concrete - Exterior Floors (Walkways, Patios, Steps and Platforms):1. Gloss Finish:a. Finish Coat: 5600 Acrylic Urethane Floor Paint, Recommended (DFT) 2 mils

Per Coat.2. Gloss Finish:a. Finish Coat: 5600 Acrylic Urethane Floor Paint VOC 100 Recommended (DFT)

1.5-2 mils Per Coat.3. Semi-Transparent Stain:a. First Coat: Concrete Semi-Transparent Water Base Stain 100 VOCb. Intermediate Coat: Concrete Semi-Transparent Water Base Stain 100 VOC.c. Finish Coat: Concrete Clear Sealer Water Base (Natural-Matte and Gloss

Finish).

D. Concrete - Exterior (Masonry, Stucco, CMU Block):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.

09960-16

E. Metal - Exterior (Galvanized, Aluminum):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.

F. Metal - Exterior (Steel, Structural Steel Columns, Joists, Trusses, Beams, Miscellaneous and Ornamental Iron):

1. Satin Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. High Gloss, Low VOC.a. Primer: Commercial CV740 System DTM Alkyd White Primer.b. Intermediate Coat: Commercial CV740 System DTM Alkyd Gloss Enamel.c. Finish Coat: Commercial CV740 System DTM Alkyd Gloss Enamel.

G. Metal - Exterior Corrosion/Rust (Ferrous Metal, Iron, Steel, Structural Steel):1. Satin Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra S-70 Water-Based Epoxy Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.4. Semi-Gloss Finish, Low VOC:a. Primer: Professional Oil Rusty Metal Primer 100 VOC.b. Intermediate Coat: Professional Oil Semi-Gloss 100 VOC.c. Finish Coat: Professional Oil Semi Gloss 100 VOC.5. Gloss Finish, Low VOC:a. Primer: Professional Oil Rusty Metal Primer 100 VOC.b. Intermediate Coat: Professional Oil Gloss 100 VOC.c. Finish Coat: Professional Oil Gloss 100 VOC.6. High Gloss, Low VOC.a. Primer: Commercial CV740 System DTM Alkyd Red Primer 100 VOC.

09960-17

b. Intermediate Coat: Commercial CV740 System DTM Alkyd Gloss Enamel 100 VOC.

c. Finish Coat: Commercial CV740 System DTM Alkyd Gloss Enamel 100 VOC.

H. Plastic - Exterior (Architectural PVC, Plastic, Fiberglass):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.

I. Vinyl - Exterior (Vinyl Siding EIFS, Synthetic Stucco):1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.

J. Wood - Exterior:1. Satin Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Satin.c. Finish Coat: Sierra Beyond Acrylic Urethane Satin.2. Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Beyond Acrylic Urethane Gloss.c. Finish Coat: Sierra Beyond Acrylic Urethane Gloss.3. Semi-Gloss Finish:a. Primer: Sierra Griptec Acrylic Primer.b. Intermediate Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.c. Finish Coat: Sierra Metalmax DTM Acrylic Urethane Semi-Gloss.

PART 3 EXECUTION

3.1 EXAMINATION

A. Review the product manufacturer's special instructions for surface preparation, application, temperature, re-coat times, and product limitations. Review product health and safety precautions listed by the manufacturer. Be responsible for enforcing on site health and safety requirements associated with the Work.

B. Do not begin installation until substrates have been properly prepared.

09960-18

C. Ensure that surfaces to receive paint are dry immediately prior to application.

D. Ensure that moisture-retaining substrates to receive paint have moisture content within tolerances allowed by coating manufacturer. Where exceeding the following values, promptly notify Architect and obtain direction before beginning work.

1. Concrete and Masonry: 13 percent. Allow new concrete to cure a minimum of 28 days.2. Exterior Wood: 17 percent.3. Interior Wood: 15 percent.4. Interior Finish Detail Woodwork, Including Trim, and Casework: 10 percent.5. Plaster and Gypsum: 15 percent.6. Concrete Slab-On-Grade: Perform calcium chloride test over 24 hour period or other acceptable test to manufacturer. Verify acceptable moisture transmission and pH levels.

E. Examine surfaces to receive coatings for surface imperfections and contaminants that could impair performance or appearance of coatings, including but not limited to, loose primer, rust, scale, oil, grease, mildew, algae, or fungus, stains or marks, cracks, indentations, or abrasions.

F. Correct conditions that could impair performance or appearance of coatings in accordance with specified surface preparation procedures before proceeding with coating application.

3.2 SURFACE PREPARATION

A. Clean surfaces thoroughly prior to coating application.1. Remove dirt, grease, oil, mold & mildew, salt and chemical contaminants by washing the surface with suitable cleaner. Rinse thoroughly with fresh water and allow to fully dry. All surfaces shall be dry at time of application.2. Remove hardware and hardware accessories, plates, machined surfaces, lighting fixtures, and similar items already installed that are not to be painted. If removal is impractical or impossible because of size or weight of the item, provide surface-applied protection before surface preparation and painting.3. After completing painting operations in each space or area, reinstall items removed using workers skilled in the trades involved.4. Cleaning: Before applying paint or other surface treatments, clean substrates of substances that could impair bond of the various coatings. Remove oil and grease before cleaning.5. Schedule cleaning and painting so dust and other contaminants from the cleaning process will not fall on wet, newly painted surfaces.6. If excessive time has elapsed since the primer was applied, remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with suitable cleaner. Rinse thoroughly with fresh water and allow to fully dry. All surfaces shall be dry at time of application.

B. Do not start work until surfaces to be finished are in proper condition to produce finished surfaces of uniform, satisfactory appearance.

C. Stains and Marks: Remove completely, if possible, using materials and methods; recommended. by coating manufacturer; cover stains and marks which cannot be completely removed with isolating primer or sealer; recommended. by coating manufacturer to prevent bleed-through.

D. Remove or protect adjacent hardware, electrical equipment plates, mechanical grilles and louvers, lighting fixture trim, and other items not indicated to receive coatings.

E. Move or protect equipment and fixtures adjacent to surfaces indicated to receive coatings to

09960-19

allow application of coatings.

F. Protect adjacent surfaces not indicated to receive coatings.

G. Prepare surfaces in accordance with manufacturer's instructions for specified coatings and indicated materials, using only methods and materials; recommended. by coating manufacturer.

3.3 SURFACE PREPARATION

A. Aluminum: Remove all oil, grease, dirt, oxide and other foreign material by cleaning per SSPC-SP1, Solvent Cleaning.

B. Block (Cinder and Concrete): Remove all loose mortar and foreign material. Surface must be free of laitance, concrete dust, dirt, form release agents, moisture curing membranes, loose cement, and hardeners. Concrete and mortar must be cured at least 30 days at 75 degrees F. The pH of the surface should be between 6 and 9, unless the products are designed to be used in high pH environments. On tilt-up and poured-in-place concrete, commercial detergents and abrasive blasting may be necessary to prepare the surface. Fill bug holes, air pockets, and other voids with a cement patching compound.

C. Concrete, SSPC-SP13/NACE 6: This standard gives requirements for surface preparation of concrete by mechanical, chemical, or thermal methods prior to the application of bonded protective coating or lining systems. The requirements of this standard are applicable to all types of cementitious surfaces including cast-in-place concrete floors and walls, precast slabs, masonry walls, and shotcrete surfaces. An acceptable prepared concrete surface should be free of contaminants, laitance, loosely adhering concrete, and dust, and should provide a sound, uniform substrate suitable for the application of protective coating or lining systems.

D. Cement Composition Siding/Panels: Remove all surface contamination by washing with an appropriate cleaner, rinse thoroughly and allow to dry. Existing peeled or checked paint should be scraped and sanded to a sound surface. Pressure clean, if needed, with a minimum of 2100 psi pressure to remove all dirt, dust, grease, oil, loose particles, laitance, foreign material, and peeling or defective coatings. Allow the surface to dry thoroughly. The pH of the surface should be between 6 and 9, unless the products are designed to be used in high pH environments.

E. Copper and Stainless Steel: Remove all oil, grease, dirt, oxide and other foreign material by cleaning per SSPC-SP 2, Hand Tool Cleaning.

F. Drywall-Interior: Must be clean and dry. All nail heads must be set and spackled. Joints must be taped and covered with a joint compound. Spackled nail heads and tape joints must be sanded smooth and all dust removed prior to painting.

G. Galvanized Metal: Clean per SSPC-SP1 using detergent and water or a degreasing cleaner to remove greases and oils. Apply a test area, priming as required. Allow the coating to dry at least one week before testing. If adhesion is poor, Brush Blast per SSPC-SP7 is necessary to remove these treatments.

H. Plaster: Must be allowed to dry thoroughly for at least 30 days before painting, unless the products are designed to be used in high pH environments. Room must be ventilated while drying; in cold, damp weather, rooms must be heated. Damaged areas must be repaired with an appropriate patching material. Bare plaster must be cured and hard. Textured, soft, porous, or powdery plaster should be treated with a solution of 1 pint household vinegar to 1 gallon of water. Repeat until the surface is hard, rinse with clear water and allow to dry.

09960-20

I. Steel: Structural, Plate, And Similar Items: Clean by one or more of the surface preparations described below as recommended by the manufacturer. Visual standards are available through the Society of Protective Coatings. A brief description of these standards together with numbers by which they can be specified follow.

1. Solvent Cleaning, SSPC-SP1: Solvent cleaning is a method for removing all visible oil, grease, soil, drawing and cutting compounds, and other soluble contaminants. Solvent cleaning does not remove rust or mill scale. Change rags and cleaning solution frequently so that deposits of oil and grease are not spread over additional areas in the cleaning process. Be sure to allow adequate ventilation.2. Hand Tool Cleaning, SSPC-SP2: Hand Tool Cleaning removes all loose mill scale, loose rust, and other detrimental foreign matter. It is not intended that adherent mill scale, rust, and paint be removed by this process. Before hand tool cleaning, remove visible oil, grease, soluble welding residues, and salts by the methods outlined in SSPC-SP1.3. Power Tool Cleaning, SSPC-SP3: Power Tool Cleaning removes all loose mill scale, loose rust, and other detrimental foreign matter. It is not intended that adherent mill scale, rust, and paint be removed by this process. Before power tool cleaning, remove visible oil, grease, soluble welding residues, and salts by the methods outlined in SSPC-SP1.4. White Metal Blast Cleaning, SSPC-SP5/NACE 1: A White Metal Blast Cleaned surface, when viewed without magnification, shall be free of all visible oil, grease, dirt, dust, mill scale, rust, paint, oxides, corrosion products, and other foreign matter. Before blast cleaning, visible deposits of oil or grease shall be removed by any of the methods specified in SSPC-SP1 or other agreed upon methods.5. Commercial Blast Cleaning, SSPC-SP6/NACE 3: A Commercial Blast Cleaned surface, when viewed without magnification, shall be free of all visible oil, grease, dirt, dust, mill scale, rust, paint, oxides, corrosion products, and other foreign matter, except for staining. Staining shall be limited to no more than 33 percent of each square inch of surface area and may consist of light shadows, slight streaks, or minor discoloration caused by stains of rust, stains of mill scale, or stains of previously applied paint. Before blast cleaning, visible deposits of oil or grease shall be removed by any of the methods specified in SSPC-SP1 or other agreed upon methods.6. Brush-Off Blast Cleaning, SSPC-SP7/NACE 4: A Brush-Off Blast Cleaned surface, when viewed without magnification, shall be free of all visible oil, grease, dirt, dust, loose mill scale, loose rust, and loose paint. Tightly adherent mill scale, rust, and paint may remain on the surface. Before blast cleaning, visible deposits of oil or grease shall be removed by any of the methods specified in SSPC-SP 1 or other agreed upon methods.7. Power Tool Cleaning to Bare Metal, SSPC-SP11: Metallic surfaces that are prepared according to this specification, when viewed without magnification, shall be free of all visible oil, grease, dirt, dust, mill scale, rust, paint, oxide corrosion products, and other foreign matter. Slight residues of rust and paint may be left in the lower portions of pits if the original surface is pitted. Prior to power tool surface preparation, remove visible deposits of oil or grease by any of the methods specified in SSPC-SP1, Solvent Cleaning, or other agreed upon methods.8. Near-White Blast Cleaning, SSPC-SP10/NACE 2: A Near White Blast Cleaned surface, when viewed without magnification, shall be free of all visible oil, grease, dirt, dust, mill scale, rust, paint, oxides, corrosion products, and other foreign matter, except for staining. Staining shall be limited to no more than 5 percent of each square inch of surface area and may consist of light shadows, slight streaks, or minor discoloration caused by stains of rust, stains of mill scale, or stains of previously applied paint. Before blast cleaning, visible deposits of oil or grease shall be removed by any of the methods specified in SSPC-SP1 or other agreed upon methods.9. High- and Ultra-High Pressure Water Jetting for Steel and Other Hard Materials: SSPC-SP12/NACE 5: This standard provides requirements for the use of high- and ultra-high pressure water jetting to achieve various degrees of surface cleanliness.

09960-21

This standard is limited in scope to the use of water only without the addition of solid particles in the stream.10. Water Blasting, SSPC-SP12/NACE No. 5: Removal of oil grease dirt, loose rust, loose mill scale, and loose paint by water at pressures of 2,000 to 2,500 psi at a flow of 4 to 14 gallons per minute.

J. Vinyl Siding, Architectural Plastics, and Fiberglass: Clean thoroughly by scrubbing with a warm, soapy water solution. Rinse thoroughly. Do not paint vinyl siding with any color darker than the original color, unless the product and color are designed for such use. Painting with darker colors may cause siding to warp.

K. Wood: Must be clean and dry. Prime and paint as soon as possible. Knots and pitch streaks must be scraped, sanded, and spot primed before a full priming coat is applied. Patch all nail holes and imperfections with a wood filler or putty and sand smooth.

3.4 INSTALLATION

A. Apply each coat to uniform coating thickness in accordance with manufacturer's instructions, not exceeding manufacturer's specified maximum spread rate for indicated surface; thins, brush marks, roller marks, orange-peel, or other application imperfections are not permitted.

B. Allow manufacturer's specified drying time, and ensure correct coating adhesion, for each coat before applying next coat.

C. Inspect each coat before applying next coat; touch-up surface imperfections with coating material, feathering, and sanding if required; touch-up areas to achieve flat, uniform surface without surface defects visible from 5 feet (1.5 m).

D. Remove dust and other foreign materials from substrate immediately prior to applying each coat.

E. Where paint application abuts other materials or other coating color, terminate coating with a clean sharp termination line without coating overlap.

F. Where color changes occur between adjoining spaces, through framed openings that are of same color as adjoining surfaces, change color at outside stop corner nearest to face of closed door.

G. Re-prepare and re-coat unsatisfactory finishes; refinish entire area to corners or other natural terminations.

3.5 CLEANING

A. Clean excess coating materials, and coating materials deposited on surfaces not indicated to receive coatings, as construction activities of this section progress; do not allow to dry.

B. Re-install hardware, electrical equipment plates, mechanical grilles and louvers, lighting fixture trim, and other items that have been removed to protect from contact with coatings.

C. Reconnect equipment adjacent to surfaces indicated to receive coatings. Relocate to original position equipment and fixtures that have been moved to allow application of coatings.

D. Remove protective materials.

3.6 PROTECTION

A. Protect installed products until completion of project.

09960-22

B. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

09960-23