section 1.qxd p1

PBPolished Brass (US3).Mirror finished CZ121/B2874 brassmaterial, machined, extruded or formed.Protected with clear, electrostaticallyapplied and oven cured powder coating.

TBSpectra Colour System (on brass).As above.

TSSpectra Colour System (on stainless steel).As above.

PZPatinating Bronze (10B).Satin finished CZ121/BS 2874 brassmaterial, machined, extruded or formed.Powder bronze finished and waxed. Finishcolour will change with level of use.

TASpectra Colour System (on aluminium).Electrostatically applied and oven curedcolour powder coating. Spectra satisfies therequirements of BS6496 and BS3900. Non-electrostatic, unaffected by ultra-violet lightand resistant to heat, acid and abrasion.Suitable for use in all climatic conditions.

TASpectra Brown Brass to match PZ (above).Electrostatically applied and oven curedpowder coating. Spectra satisfies therequirements of BS 6496 and BS 3900.Non-electrostatic, unaffected by ultra-violetlight and resistant to heat, acid andabrasion. Suitable for use in all climates.

www.modricusa.com Tel : 800-739-0202 Fax : 800-813-2128

BioCote

BSClear anti-bacterial BioCote finish onstainless steel.Oven cured powder coating effectiveagainst harmful micro-organisms includingMRSA, E-Coli and Salmonella.

BDDark mica BioCote anti-bacterial finish,generally on aluminium.Oven cured powder coating effectiveagainst harmful micro-organisms includingMRSA, E-Coli and Salmonella.

BLLight mica BioCote anti-bacterial finish,generally on aluminium.Oven cured powder coating effectiveagainst harmful micro-organisms includingMRSA, E-Coli and Salmonella.

In conjunction with good hygiene practicessuch as increased surveillance, greatereducation and frequent hand washingBioCote offers a secondary level ofprotection against cross-contamination.

BioCote is an effective product inprotection against harmful bacteriaincluding MRSA, E-Coli and Salmonella.BioCote inhibits the growth of micro-organisms thus forming an effective part ofa good hygienic procedure.

BioCote does not function in the same wayas antibiotics and therefore, to date, nobacteria have become resistant to BioCoteas they can to some antibiotics.

BioCote is durable and the advanced-surface coating under normal use will lastat least 10 years. The surface finish is moreresistant to chipping, scratching, fading andwear than other wet-sprayed finishes. Thecoating is applied through the “heat-seal-oven-baked” process and is permanentlycoated to ironmongery products.

Over 5 years of research, testing anddevelopment has been carried out.Products are independently tested anddemonstrate the antibacterial effectivenessthroughout the product’s lifetime.

BioCote offers that extra level of protectionin the fight against infection, particularlyrelevant considering there is an increase inthe number of antibiotic resistant bacteria.

BioCote is a patent-protected powdercoating technology that has excellentadvanced anti-bacterial qualities. The activeagent is based on natural products that areproven to be safe.


Care and maintenance

Once fitted and in use, it is essential thatregular inspection and cleaning is carriedout to give many years of satisfaction.

FinishesPreventing corrosion and deterioration iseasier than trying to restore a qualityfinish. To avoid the risk of damage,decorative and other exposed items ofhardware should not be fitted untilimmediately before handover of the areaand after the work of other trades in thearea is complete.

Hardware should not be fitted to anysurface before the decoration of the surfaceis complete. If subsequent redecoration ortouching up is required, the hardwareshould be removed from the surface andrefitted after the finish is fully dry. In nocircumstances should masking tape or thelike be applied to hardware surfaces, as thismay damage protective coatings.

The following list is a general guide to careand maintenance of finishes. Wherereference is made to aerosol lubricants, werecommend ‘WD40’ or a PTFE lubricant.

Modric Anodised Aluminium – MAWipe clean with a weak solution ofwashing-up liquid using a soft cloth orsponge.

Satin Stainless Steel and Platinic Stainless Steel – SS • PSWipe clean with a medium strengthdetergent or white spirit using a soft clothor sponge. In the event of dirt havingaccumulated, application of aerosollubricant prior to standard cleaning isrecommended. A harsh brush should neverbe used.

Polished Brass, Patinting Bronze,BioCote and Spectra Colour Coating –PB • PZ • BS • BC • BD • TAWipe clean with a weak solution ofwashing-up liquid using a soft cloth orsponge, rinse and dry with a dry soft cloth.Do not use any form of metal polish orabrasive as this will destroy the protectivecoating.

Note: The proprietary products mentionedabove are given only as a guide for thequality to be used.

See ‘Care and Maintenance’ at thebeginning of each section.

Allgood Hardware Pozidriv/SupadrivscrewsAllgood Hardware Pozidriv/Supadriv screwsshould be driven home so that the slots onthe heads are horizontally and verticallyaligned. The correct size Allgood Hardwarescrewdriver must be used (see below).Particular care should be taken when fixingSpectra coated screws; each fixing shouldfirst be ‘piloted’ with an equivalent screwwhich can then be replaced with theSpectra coated one.

XX5321Pozidriv/Supadriv screwdriver, for 4–6g self-tapping screws.XX5322Pozidriv/Supadriv screwdriver, for 6–10gwood screws.XX5323Pozidriv/Supadriv screwdriver, for 12–16gscrews.

Allen screw fixingsWhere Allen screw fixings are used, theappropriate key is provided.

GeneralAll fixings and grub screws must be secure,and this should be checked regularly; loosefixings allow ‘play’ which will reduce thelongevity of all architectural hardware andpossibly cause damage to the door face.


Sembla

3.2

SemblaThe door handle is special. In a way it isthe last bastion of expression for thearchitect. Whilst most other buildingcomponents have become entirelystandardised or entirely customised, doorfurniture manufacturers offer a vast rangeof styles to cater for all architectural trends.

Sembla is the latest range from Allgood.This component system establishes a newdirection for architectural ironmongery bylaunching a complete original method ofconstructing door furniture.

Sembla offers a distinctive but recognisableimage – functional and consistent in itsmechanism but easily adaptable –attractive to architect and to client alike.

It was created by the UK design groupA.S.K. in partnership with Allgood, anddraws on the designers’ substantialexperience in designing building productsthroughout Europe.

Sembla is built up around a core piece –the node – which makes the physicalconnection to the lock, the door or thewall.

Around the node, a choice of levers, pullhandle grips and tips are assembled in thefactory to form complete products. In thisway, a variety of door handles is available,all with a uniting element which identifiesthem as Sembla.

The proportion and detailing of the junctionbetween node, tip and lever ensure thatthe simplest lever handle will stand as aclassic. Other tip and lever designs createmore design options and the choice of tipsand levers can be used on either end of theSembla pull handle.

The materials options Sembla has, allow itto facilitate zoning, thus the basement of abuilding as well as the boardrooms can beaccommodated within the range – usingthe same mechanism-to-lock interface.

All lever handles are factory assembledusing patented military specification, self-locking thread form fixings.

Items are available in anodised aluminiumor Grade 316 satin or polished stainlesssteel and are designed to operate inconjunction with the Allgood hardwarerange of mechanical products.

The Sembla designs conceal a strength anddurability suited to the most arduous ofenvironments.

Exhaustive tests have been conducted inexcess of European Standards requirementsand the entire Sembla programme carries a10 year warranty. The handles shown onthe following pages are the standardrecommended configurations which areavailable from stock.

All Sembla lever sets have 3rd party testevidence to BS EN 1906, classification.4 7 – 1 1 4 0 U


Sembla lever handles

57

20

147

57

20

147

Sembla 3623Pair of 20øx147x57mm Sembla Cylinderlever handles, with Drum tips, on 50øx3mmconcealed Quadaxial fixing roses.Finishes: SS • PS • ST • SP • MA • AS

Sembla 3643Pair of 20øx147x57mm Sembla Cylinderlever handles, with Bullet tips, on 50øx3mmconcealed Quadaxial fixing roses.Finishes: SS • PS • ST • SP • MA • AS


Sembla lever handles

57

20

148

57

20

148

57

20

146

Sembla 3626Pair of 20øx148x57mm Sembla Crescentlever handles, with Drum tips, on 50øx3mmconcealed Quadaxial fixing roses.Finishes: SS • PS • ST • SP • MA • AS

Sembla 3646Pair of 20øx148x57mm Sembla Crescentlever handles, with Bullet tips, on 50øx3mmconcealed Quadaxial fixing roses.Finishes: SS • PS • ST • SP • MA • AS

Sembla 3640Pair of 20øx146x57mm Sembla Propellerlever handles, with Bullet tips, on 50øx3mmconcealed Quadaxial fixing roses.Finishes: SS • PS • ST • SP


Sembla pull handles

Sembla 162720øx353x65mm Sembla pull handle withDrum tips both ends. Bolt through fixings.Fixing centres at 300mm.Finishes: SS • PS • ST • SP • MA • AS

Sembla 1627BBPair, as above, with back-to-back fixings.

Sembla 162920øx653x65mm, with fixing centres at600mm.Finishes: SS • PS • ST • SP


Sembla 164720øx353x65mm Sembla pull handle withBullet tips both ends. Bolt through fixings.Fixing centres at 300mm.Finishes: SS • PS • ST • SP • MA • AS


Sembla 164920øx653x65mm, with fixing centres at600mm.Finishes: SS • PS • ST • SP


Other lengths available to special order.Please note, the maximum recommendedfixing centres utilising two fixings is1000mm.

353/653 300/600

6520

353/653 300/600

6520


3.2

Sembla pull handles

Sembla 163720øx540x65mm Sembla pull handle withCylinder tips both ends. Bolt throughfixings. Fixing centres at 300mm.Finishes: SS • PS • ST • SP • MA • AS


Sembla 163920øx840x65mm with fixing centres at600mm.Finishes: SS • PS • ST • SP


Sembla 166720øx540x65mm Sembla pull handle withCrescent tips both ends. Bolt throughfixings. Fixing centres at 300mm.Finishes: SS • PS • ST • SP • MA • AS

N.B. For pull handles on glass doors pleasecontact your local Allgood office.


Sembla 166920øx840x65mm with fixing centres at600mm.Finishes: SS • PS • ST • SP


540/840 300/600

6520

540/840 300/600

6520


Mode

3.3

Mode is the programme of striking, uniquedoor furniture, designed and produced byAllgood. Mode products were originallyconceived by Alan Tye, Royal Designer forIndustry, for inclusion within the Modricrange.

Now Mode has come to represent a classicrange including examples of the best of UKdoor furniture available.

Mode is a range of distinctive designs, suchas Quaver, Reflex and Haft, which lend abuilding a more characterful air whilst stillaccording with the pure and classicalprinciples of their Modric origins.

Sembla, Mode and Modric are fullycompatible and interchangeable. Each ofthe families of products within Mode hasan individual flavour and each incorporateslever handles, pull handles and accessoriessuitable for modern, commercial and publicbuildings which demand highly durableproducts.

The ergonomic designs and range ofmetallic finishes have made Modeattractive to specifiers and building ownersalike. Mode has not only become known asthe very best of British designed-and-manufactured door furniture, but issupported by the comprehensive range ofAllgood Hardware mechanical items, suchas locks, hinges, panic hardware, doorclosers and floor springs.

Products are available from stock, ensuringthe fastest delivery anywhere in the world.All items are hand finished and all Modeitems carry a 10 year guarantee.

ReflexWithin Mode, the Reflex family includeslever and pull handles, bespoke backplatesand knob furniture. All products areavailable in the full range of Allgoodmetallic finishes. The Straight, ‘L’ andQuadrant shaped Reflex pull handles allowfor varying permutations and the creationof individual but minimal aesthetic.

QuaverQuaver is a family of ergonomicallydesigned handles suitable for heavy dutyapplications. The sophisticated formingprocess used to manufacture Quaverresults in products that can be oriented inmany directions. Quaver is available in thefull range of Allgood metallic finishes andincorporates safety lever handles as well aspull handles.

HaftIt is no coincidence that Haft (the MiddleEnglish word for handle, evoking traditionalvalues of craftsmanship and quality) hasbeen chosen as the banner for this range oftactile Mode furniture.

Haft is manufactured in grade 316 stainlesssteel with a Ceramicast texture and definedhighlights – either polished or satin.

The textured nature of Haft items; thecontrasting finishes, all serve to add to thevisual and tactile interaction betweenindividual and environment.

All Mode lever sets have 3rd party testevidence to BS EN 1906, classification.4 7 – 1 1 4 0 U

Mode


Mode lever handles

Mode 3512Pair of 22øx136x54mm Quaver heavy dutysafety lever handles on 50øx3mmconcealed Quadaxial fixing roses.Finishes: SS • PS • MA • TA • PB • PZ

Mode 3504Pair of 137x61mm Reflex lever handles on50øx3mm concealed Quadaxial fixingroses.Finishes: SS • PS • MA • TA • PB • PZ

5422

136

61

137

11

22


Mode lever handles

Mode 3537Pair of 143x25x48mm operating Arc Haftson 50øx3mm concealed Quadaxial fixingroses.Finishes: SS • PS

Mode 3538Pair of 135x27x46mm operating EllipseHafts on 50øx3mm concealed Quadaxialfixing roses.Finishes: SS • PS

Mode 3539Pair of 126x26x58mm operating CornuHafts on 50øx3mm concealed Quadaxialfixing roses.Finishes: SS • PS

48

143

25

46

135

27

126

26

58


Mode pull handles

Mode 6587L/R22øx305x57mm Quaver pull handle withbolt through fixings. Fixing centres at285.5mm (diagonal).STATE HAND. Left hand shown.Finishes: SS • PS • MA • TA • PB • PZ

Mode 6587BBL/RPair, as above, with back-to-back fixings.

Mode 6585L/R22øx152x57mm with fixing centres at135mm (diagonal).Finishes: SS • PS • MA • TA • PB • PZ


Mode 6586L/R22øx228x57mm with fixing centres at209mm (diagonal).Finishes: SS • PS • MA • TA • PB • PZ


Mode 1425237x30x44mm Straight Reflex pull handlewith bolt through fixings. Fixing centres at203mm.Finishes: SS • PS • MA • TA • PB • PZ

Mode 1425BBPair, as above, with back-to-back fixings.

Mode 1421Quadrant shaped version, with fixingcentres at 172.5mm.Finishes: SS • PS • MA • TA • PB • PZ


Mode 1401N‘L’ shaped version, with fixing centres at172.5mm.Finishes: SS • PS • MA • TA • PB • PZ

Mode 1401NBBPair, as above, with back-to-back fixings.

NoteBoth 1421 and 1401N have Quadrant orSquare backplate options available.

152

152

152/228/305

22

5738LEFT HAND SHOWN


Mode pull handles

Mode 1537262x31x55mm Fixed Arc Haft with boltthrough fixings. Ceramicast solid 316stainless steel with tactile non-slip grip,and defined highlights in satin or polishedstainless steel. Fixing centres at 180mm.Finishes: SS • PS


Mode 1538264x35x53mm Fixed Ellipse Haft with boltthrough fixings. Ceramicast solid 316stainless steel with defined highlights insatin or polished stainless steel. Fixingcentres at 180mm.Finishes: SS • PS


Mode 1539234x29x77mm Fixed Cornu Haft with boltthrough fixings. Ceramicast solid 316stainless steel with defined highlights insatin or polished stainless steel. Fixingcentres at 180mm.Finishes: SS • PS


262

10

31 55

264

15

35 53

7729

22

234


Modric

ModricWhen Alan Tye (Royal designer for Industry)conceived Modric in 1965, he could never,even in his wildest dreams, have imaginedthe strength and longevity of the range’ssuccess.

Born out of the desire to create a trulydimensionally and aesthetically compatiblerange of ironmongery, the Modric(modular/metric) product was the trueoriginal in a field where designconsideration had previously been ignored.

Modric has evolved with new designs, innew materials and new finishes, all ofwhich can trace their roots back to theoriginal uncompromising design concept.The Allgood range has expanded intomechanical hardware, access control andnew technologies. We strive however tomaintain a comprehensive unifyingaesthetic that adheres to the originalModric principles.

Since its inception Modric has beenrenowned for fine design and extraordinarydurability; principles Allgood still takesgreat pride in today.

Modric is the background to the success ofAllgood. Created in the 60s, Modric was atotally innovative and modern concept indesign. Over 40 years later, the companyand product range are still No 1 for finedesign and product quality.

All Modric lever sets have 3rd party testevidence to BS EN 1906, classification.4 7 – 1 1 4 0 U


3.4

Modric lever handles

125

17

50

Modric 3501Pair of 17øx125x50mm safety lever handleson 50øx3mm concealed Quadaxial fixingroses.Finishes: SS • PS • MA • TA • PB • PZ

127

19

52

Modric 3502Pair of 19øx127x52mm safety lever handleson 50øx3mm concealed Quadaxial fixingroses.Finish: MA • TA • PB • PZ

All Modric lever sets have 3rd party test


Modric lever handles

125

19

52

Modric 3503Pair of 19øx125x52mm lever handles on50øx3mm concealed Quadaxial fixingroses.Finish: MA • TA • PB • PZ

133

22

55

Modric 3506Pair of 22øx133x55mm Dom heavy dutysafety lever handles on 50øx3mmconcealed Quadaxial fixing roses.Finishes: SS • PS • MA • TA • PB • PZ

11824

59

Modric 3515Pair of 118x59mm shaped lever handles on50øx3mm concealed Quadaxial fixingroses.Finishes: SS • PS • MA • TA • PB • PZ


Modric pull handles

Modric 6999C17øx300x52mm Pull handle, with boltthrough fixings. Fixing centres at 284mm.Finishes: SS • PS • MA • TA

Modric 657117øx127x50mm with fixing centres at110mm.Finishes: SS • PS • MA • TA • PB

Modric 6999B17øx225x52mm with fixing centres at209mm.Finishes: SS • PS • MA • TA

Modric 659619øx305x70mm Pull handle, with boltthrough fixings. Fixing centres at 286mm.Finish: MA • TA • PB • PZ

Modric 6596BBPair, as above, with back-to-back fixings.

Modric 659719øx610x70mm with fixing centres at591mm.Finish: MA • TA • PB • PZ


Modric 6570As above, with concealed face fixings,for solid doors.Finishes: SS • PS • MA • TA • PB

127/225/300 110/209/284

50/5217

305/610 286/591

19 70


Modric pull handles

Modric 657622øx133x55mm Pull handle, to match 3506N lever, with bolt through fixings.Fixing centres at 111mm.Finishes: SS • PS • MA • TA • PB

Modric 657522øx133x55mm Pull handle, to match3506N lever, with concealed face fixings,for solid doors. Fixing centres at 111mm.Finishes: SS • PS • MA • TA • PB • PZ

133 111

5522

Modric 657722øx133x55mm Pull handle, with rose tomatch 3506N lever, with bolt throughfixings. Fixing centres at 111mm.Finishes: SS • PS • MA • TA • PB

133111

5522

Modric 6577BBAs above, pair, with back-to-back fixings.Finishes: SS • PS • MA • TA • PB

Modric 6578As above, single, with concealed facefixings. For solid doors.Finishes: SS • PS • MA • TA • PB

Modric 656725øx305x76mm Pull handle, with boltthrough fixings. Fixing centres at 280mm.Finishes: SS • PS • MA • TA • PB • PZ


Modric 656425øx152x76mm with fixing centres at127mm.Finishes: SS • PS • MA • TA • PB • PZ


Modric 656225øx228x76mm with fixing centres at203mm.Finishes: SS • PS • MA • TA • PB • PZ


Modric 6563NAs above, with concealed face fixings, forsolid doors.Finishes: SS • PS • MA • TA • PB • PZ


Modric push plates & kickplates

Modric 6800J620x76x3mm push plate.Finishes: SS • PS • MA • TA • PB • PZ

Modric 6800A325x76x3mm push plate.Finishes: SS • PS • MA • TA • PB • PZ

Modric 6800E325x152x3mm push plate.Finishes: SS • PS • MA • TA • PB • PZ

76

620

76

325

152

325

Modric 6850Standard 3mm thick kicking plate. Drilledand countersunk with screws.Finishes: SS • PS • MA • TA • PB • PZ (SS &PS 2.5mm)

6850/1151000x115x3mm kicking plate.6850/1201000x120x3mm kicking plate.6850/415400x150x3mm kicking plate.6850/420400x200x3mm kicking plate.6850/815800x150x3mm kicking plate.6850/820800x200x3mm kicking plate.6850/915900x150x3mm kicking plate.6850/920900x200x3mm kicking plate.

Modric 6851Standard 1.5mm thick kicking plate. Drilledand countersunk with screws.Finishes: SS • PS • MA • TA • PB • PZ

6851/1151000x150x1.5mm kicking plate.6851/1201000x200x1.5mm kicking plate.6851/295295x150x1.5mm kicking plate.6851/395395x150x1.5mm kicking plate.6851/415400x150x1.5mm kicking plate.6851/420400x200x1.5mm kicking plate.6851/695695x150x1.5mm kicking plate.6851/795795x150x1.5mm kicking plate.6851/815800x150x1.5mm kicking plate.6851/820800x200x1.5mm kicking plate.6851/895895x150x1.5mm kicking plate.6851/915900x150x1.5mm kicking plate.6851/920900x200x1.5mm kicking plate.

Other lengths available to special order.


Cabinet pulls and knobs

6999A13øx152x40mm Modric pull handle, withbolt through fixings. Centres at 139mm.Finishes: SS • PS • MA • TA

1711152x10x25mm Modric handle for slidingdoors, with bolt through fixings. Centres at110mm.Finishes: MA • TA

1712228x10x25mm Modric handle for slidingdoors, with bolt through fixings. Centres at178mm.Finishes: MA • TA

1202228x25x38mm Pull handle with boltthrough fixings. Suitable for doors10–55mm thick. Centres at 214mm.Finishes: MA • TA

100478x19x25mm Modric handle, straight, boltthrough fixings. Centres at 66mm.Finishes: MA • TA

100278x10x25mm Modric handle, straight, boltthrough fixings. Centres at 66mm.Finishes: MA • TA

228 214

14

25 38

78

2519

66

78

2510

66

228 178

2510

1202BBPair, as above, with back-to-back fixings.

139

13

152

40

152 100

2510



6260152x76x22mm Modric handle for slidingdoors, with bolt through fixings. Centres at110mm. Has been successfully tested to BSEN 1634 for 30 and 60 minutes.Finishes: SS • PS • MA • TA • PB • PZ

621576x38x13x3mm Modric sliding door ordrawer flush pull.Finishes: SS • PS • MA • TA

251629øx29mm Modric cabinet knob completewith face and bolt through fixings.Finishes: SS • PS • MA • TA • PB • PZ


620047x10x3mm Modric sliding door flush pullwith lip.Finishes: PC • MA

620547x10x3mm Modric sliding door flush pullwith off-centre lip.Finish: MA • TA

47

10

2119

47

10

624576x76x11mm Flush ring handle, with 8mmspindle.Finishes: SC • PC • PB • PZ

76

1170

6250152x152x22x3mm Flush pull handles, pair,with back-to-back fixings. Can be usedsingly. Has been successfully tested to BSEN 1634 for 30 and 60 minutes.Finishes: SS • PS • MA • TA • PB • PZ

152

223

152

152

223

76

76

38 13

29

29



1009129x30mm Sembla cabinet pull. Centres at96mm.Finishes: SS • PS

255115øx30x33mm Sembla cabinet pull.Finishes: SS • PS



161

128

30

15 15

193

160

30

15 15

33

30

15

252629øx40mm Modric Dom cabinet knobcomplete with face and bolt throughfixings.Finishes: SS • PS • MA • TA • PB • PZ

252719øx29mm Modric Dom cabinet knobcomplete with face and bolt throughfixings.Finishes: SS • PS • MA • TA • PB • PZ


1929

22 9

30

29

40

129

96

30

15 15



1716/2070x200mm Ledge sliding door or drawerpull handle.Finishes: SS • PS • MA

1714/1045x100mm Ledge sliding door or drawerpull handle.Finishes: SS • PS • MA

70

30

3

45

30

3


Hooks

655747x57x62mm Sembla hat and coat hook onconcealed fixing rose.Finishes: SS • PS

655085x13x50mm Modric hat and coat hook.Finishes: PC • MA • TA • PB • PZ

655188x13x53mm Modric hat and coat hookwith rubber buffer.Finishes: PC • MA • TA • PB • PZ

655540x13x18mm Modric coat hook.Finishes: PC • MA • TA • PB • PZ

1813

85

501813

88

53

1813

40

654670x22x55mm Grenadier heavy duty hatand coat hook.Finishes: MA ● TA

6122

70

5522

70

654770x22x61mm Grenadier heavy duty hatand coat hook with rubber buffers.Finishes: MA ● TA

654870x22x55mm Grenadier heavy duty coat hook.Finishes: MA ● TA

5522

70

47 62

5720


Cylinder pulls

176x38x18mm Pull for round cylinder.Finishes: SS • PS • MA • TA • PB • PZ

38 18

76

676x38x18mm Pull for oval cylinder.Finishes: SS • PS • MA • TA • PB • PZ

38 18

76

776x38x18mm Pull.Finishes: MA ● TA ● PB

38 18

76

2L/R76x76x18mm Pull for round cylinder or2102 escutcheon insert.STATE HAND. Left hand shown.Finishes: MA ● TA

76 18

76

19

876x38x18mm Pull for Euro profile cylinder.Finishes: SS • PS • MA • TA • PB • PZ

38 18

76

16L/R76x76x18mm Pull for Euro profile cylinder.STATE HAND. Left hand shown.Finishes: MA ● TA

76 18

76

19

576x38x18mm Pull for round cylinder or2102 escutcheon insert.Finishes: MA ● TA

38 18

76


Escutcheons and roses

794Q50øx3mm Escutcheon for oval cylinders,concealed fixings.Finishes: SS • PS • MA • TA • PB

3

50

796Q50øx3mm Escutcheon for Euro profilecylinders, concealed fixings.Finishes: SS • PS • MA • TA • PB • PZ

3

50

2155Q50øx3mm Escutcheon for lever lock,concealed fixings.Finishes: SS • PS • MA • TA • PB • PZ

3

50

74063mmø Covered round roses, pair, withhole for lever retrofit fixing for use withtubular latch in doors pre-bored with a54mmø hole.Finishes: SS • PS • MA • TA • PB

52

33

63

2110K38øx3mm Escutcheon for budget lock.Offset 16.5mm hole.Finishes: SS • PS • MA • TA

3

3816.5

74163x76mm Covered oblong roses, pair,with hole for lever retrofit fixing for usewith tubular latch in doors pre-bored witha 54mmø hole.Finishes: SS • PS • MA • TA • PB

52

7633

63

761Q50øx3mm Plain multi-purpose disc,concealed fixings.Finishes: SS • PS • MA • TA • PB • PZ

3

50

2157Q50øx3mm Escutcheon for lever lock, withpierced keyhole and swing cover.Finishes: SS • PS • MA • TA • PB • PZ

50

3

2111KQ50øx3mm Escutcheon for budget lock,concealed fixings. Offset 16.5mm hole.Finishes: SS • PS • MA • TA

3

50

16.5


Door fittings

6001305x80x3mm Letter plate with 250x44mmspring loaded flap, fixing centres at267mm, for doors 40–55mm thick.Finishes: SS • PS • MA • PB

6003305x76x3mm Tidy for inside use with 6001,as shown above.Finishes: SS • PS • MA • PB

305

250267

80

3

44

305

228267

76

3

44

698047x8mm Door viewer with swivel cover.Finishes: SS • PS • MA • TA

160°

8

47

6010381x152x3mm Letter plate with305x76mm gravity flap, fixing centres at344mm, for doors 40-55mm thick.Finishes: SS • PS • MA • PB

381

305

344

76

3

152

6012381x152x3mm Tidy for inside use with6010, as shown above.Finishes: SS • PS • MA • PB

381

305

344

76

3

152

6002As 6001, complete with inside tidy andgaskets for glass doors. 10–15mm thick.


Door fittings

230147øx38mm Floor door stop.Finishes: SS • PS • MA • TA • PB • PZ

230232øx32mm Floor door stop.Finish: MA • TA

231147øx42mm Sembla door stop. Black naturalrubber, on stainless steel or aluminiumrose.Finishes: SS • PS • MA

35

38

47

22

32

32

42

47

230725øx102mm Skirting buffer.Finishes: SS • PS • MA • TA • PB • PZ

2303Fixing for concrete, for 2301 and 2302 floor door stops.

230847øx26mm Wall mounted door bumper.Finishes: MA • TA • PB • SS • PS

3247

26

655219øx63mm Modric bumper hook.Finishes: SS • PS • MA • TA • PB

1619

63

230519øx63mm Skirting buffer.Finishes: SS • PS • MA • TA • PB • PZ

1619

63

102

25


Accessories

843276mmø ‘Male’ international symbol.Finishes: SS • PS • MA • TA • PB

843376mmø ‘Female’ international symbol.Finishes: SS • PS • MA • TA • PB

843576mmø ‘Disabled’ international symbol.Finishes: SS • PS • MA • TA • PB

843476mmø sign. ‘Unisex’ international symbol.Finishes: SS • PS • MA • TA • PB

844876mmø sign. ‘Fire door keep locked’ toBS5499.Finishes: SS • PS • MA • TA • PB

844976mmø sign. ‘Fire door keep shut’ toBS5499.Finishes: SS • PS • MA • TA • PB

Alternative graphics available. For furtherinformation, please contact your localAllgood office.

844776mmø sign. ‘Automatic fire door keepclear’ to BS5499.Finishes: SS • PS • MA • TA • PB


Entrance pull handles

Sembla 172938øx692x100mm Sembla pull handle withDrum tips both ends. Bolt through fixings.Fixing centres at 600mm.Finishes: SS • PS • MA


Sembla 1729CCranked version of 1729.Finishes: SS • PS • MA

Sembla 1729CBBPair, as above, with back-to-back fixings.

Mode 1374610x38x64mm Mode Reflex pull handle,with bolt through fixings. Adjustable fixingcentres factory-set at 413mm.Finishes: SS • PS • MA • TA • PB


Mode 1372380x38x64mm with adjustable fixingcentres factory-set at 264mm.Finishes: SS • PS • MA • TA • PB


Modric 656925øx610x76mm Modric pull handle withbolt through fixings. Fixing centres at585mm.Finishes: SS • PS • MA • TA • PB • PZ





Mode 133538øx463x223mm Semicircular pull handle,single, with bolt through fixings.90mm projection.Fixing centres at 425mm.Finishes: SS • PS • TA • PB • PZ

90

38

463 425

223

30

175120øx750x67mm Pull handle withbolt through fixings. Fixing centres at600mm.Finishes: SS • PS

176120øx750x70mm Pull handle withbolt through fixings. Fixing centres at600mm.Finishes: SS • PS



67

750 600

20 67

750 600

20



Modric 1359N50øx302x96mm Guardsman Minor crankedpull handles, pair, with back-to-backfixings. Suitable for doors 10-64mm thick.Fixing centres at 254mm.Finishes: SS • PS • MA • TA • PB • PZ

302 254

50

96

100

Modric 1360N50øx610x96mm Guardsman cranked pullhandles, pair, with back-to-back fixings.Suitable for doors 10-64mm thick.Fixing centres at 425mm.Finishes: SS • PS • MA • TA • PB • PZ

Modric 1350N50øx610x96mm Guardsman straight pullhandles, pair, with back-to-back fixings.Suitable for doors 10-64mm thick.Fixing centres at 425mm.Finishes: SS • PS • MA • TA • PB • PZ

Modric 1349N50øx302x96mm Guardsman Minor straight pull handles, pair, with back-to-back fixings. Suitable for doors 10-64mmthick. Fixing centres at 254mm.Finishes: SS • PS • MA • TA • PB • PZ

302 254

50

96

Guardsman entrance pull handles aresupplied in pairs.

Modric 1356Guardsman entrance pull handles are always supplied in pairs with back-to-back fixings.If single side fixing is required, specify 1356fixing pack for bolt through fixing.

Other lengths available to special order.Please note, the maximum recommendedfixing centres utilising two fixings is4000mm.

Modric 1361N50øx2112x96mm Guardsman Majorcranked pull handles, pair, with back-to-back fixings. Suitable for doors 10-64mmthick. Fixing centres at 2064mm.Finishes: SS • PS • MA • TA • PB • PZ

Modric 1351N50øx2112x96mm Guardsman Majorstraight pull handles, pair, with back-to-back fixings. Suitable for doors 10-64mmthick. Fixing centres at 2064mm.Finishes: SS • PS • MA • TA • PB • PZ

2112 2064

50 96


47 16

62

Modric 2500*47øx62mm Dom knob furniture, pair.Suitable for doors 35-55mm thick.Photograph shows product with 750 rose.Finishes: SS • PS • MA • TA • PB • PZ

Modric 2501*47øx42mm Knob furniture, pair.Suitable for doors 35-55mm thick.Photograph shows product with 750 rose.Finishes: MA

47 16

42

Modric 2505*47øx42mm Knob furniture, pair, 1.5mmradius edge. Suitable for doors 35-55mmthick.Photograph shows product with 750 rose.Finishes: SS • PS • MA • TA • PB • PZ

47

42

16

Modric 250347øx42mm Fixed knob assembly for 10-13mm thick glass doors, pair. Can alsobe used in pairs or singly on wood/metaldoors 35-55mm thick.Finish: MA

Modric 251047øx62mm Dom fixed knob assembly for10-13mm thick glass doors, pair. Can alsobe used in pairs or singly on wood/metaldoors 35-55mm thick.Finishes: SS • PS • MA • TA • PB • PZ

47

42

Modric 251147øx42mm Fixed knob assembly withradius edge for 10-13mm thick glass doors,pair. Can also be used in pairs or singly onwood/metal doors 35-55mm thick.Finishes: SS • PS • MA • TA • PB • PZ

47

42

47

62

Knobs


Knobs and accessories

Knobs and accessories

2504*47øx62mm Reflex knob furniture, pair,with 8mm spindle. Suitable for doors 35-55mm thick. Product shown with 750rose. Right hand shown.Finishes: SS • PS • MA • TA • PB • PZ

251447øx62mm Reflex knob assembly, pair,for glass doors 10-13mm thick. Can also be used in pairs or singly on wood/metaldoors 10-55mm thick.Finishes: SS • PS • MA • TA • PB • PZ

62

47

20

47

62

20

75047øx3mm Rose for knobs.Finishes: SS • PS • MA • TA • PB • PZ

3

47

76147øx3mm Plain multi-purpose disc,concealed fixings.Finishes: SS • PS • MA • TA • PB • PZ

3

47

79647øx3mm Escutcheon for Euro profilecylinders, concealed fixings.Finishes: SS • PS • MA • TA • PB • PZ

3

47

2155N47øx3mm Escutcheon for lever lock,concealed fixings.Finishes: SS • PS • MA • TA • PB • PZ

3

47

771/252147øx3mm Rose and snib turn for bathroomlocks, concealed fixing, 5 and 8mm spindlesincluded.Finishes: SC • PC • MA • PB • PZ

3

47

22

771/253147øx3mm Rose and heavy snib turn forbathroom locks, concealed fixing, 5 and8mm spindles included.Finishes: SS • PS • MA • TA • PB • PZ

3

47

30

77947øx3mm Rose with indicator and stainlesssteel emergency release, concealed fixing,for use with 5001A indicating bolt,771/2521 or 771/2531 rose and snib turn.5mm spindle.Finishes: SS • PS • MA • TA • PB • PZ

3

47

60

78647øx3mm Rose with stainless steelemergency release only, concealed fixing,for use with 5001A indicating bolt,771/2521 or 771/2531 rose and snib turn. 5mm spindle.Finishes: SS • PS • MA • TA • PB • PZ

3

47

60

79447øx3mm Escutcheon for oval cylinders,concealed fixings.Finishes: SS • PS • MA • PB • PZ

3

47

215747øx3mm Escutcheon with pierced keyholeand swing cover.Finishes: SS • PS • MA • PB • PZ

47

33


Lock functions

latch – free access

FunctionLatchbolt is withdrawn by lever handlefrom both sides. No security is provided.

UsageDoors which are required to be held shutfor environmental or privacy reasons. Notusually specified for self-closing corridor orlobby doors.

Inside Edge Outside

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop, 2 kicking plates, 2 “Fire door keepshut” symbols*.

Ancillary hardware (leaf & a half, with plain meeting stile)3 pairs of hinges, 1 Fig.1 door closer*, 1 flush bolt set, 2 door stops, 4 kicking plates,4 “Fire door keep shut” symbols*.

Ancillary hardware (double door, with plain meeting stile)3 pairs of hinges, 2 Fig.1 door closers*, 1 flush bolt set, 2 door stops, 4 kicking plates,4 “Fire door keep shut” symbols*.

* It is usually required that fire rated doors be self-closing and have the appropriate firedoor signage. Non-fire rated doors need not have either of these items. For double doors adoor selector is usually required in order to ensure correct closing sequence.

All details are based on a leaf size of 2100x800mm.For details of the ancillary hardware suggested, please refer to Section 5.

Examples


Lock functions

lock – controlled access

FunctionLatchbolt is operated by lever handle fromboth sides. Deadbolt and latchbolt areoperated by key from outside and eitherturn (as shown above) or key from inside(see cylinder options, Section 5.2). Boltthrow is 20mm with single turn of the key.

UsageDoors which are required to be held shutfor privacy or environmental reasons butalso to be capable of being locked forsecurity purposes. Not usually specified forself-closing corridor or lobby doors.

Inside Edge Outside

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop, 2 kicking plates, 2 “Fire door keepshut” symbols*.

Ancillary hardware (leaf & a half, with plain meeting stile)3 pairs of hinges, 1 Fig.1 door closer*, 1 flush bolt set, 2 door stops, 4 kicking plates,4 “Fire door keep shut” symbols*.

Ancillary hardware (double door, with plain meeting stile)3 pairs of hinges, 2 Fig.1 door closers*, 1 flush bolt set, 2 door stops, 4 kicking plates,4 “Fire door keep shut” symbols*.

* It is usually required that fire rated doors be self-closing and have the appropriate firedoor signage. Non-fire rated doors need not have either of these items. For double doors adoor selector is usually required in order to ensure correct closing sequence.


Examples


Lock functions

bathroom – privacy

FunctionLatchbolt is operated by lever handle fromboth sides. Deadbolt for privacy is operatedby inside snib turn. External emergencyrelease, with indicator if required (bothversions are supplied).

UsageAny bathroom, toilet, examination orsimilar room where privacy is required butwhere access in emergency is desired.

Inside Edge Outside

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 door stop, 2 kicking plates, 1 toilet door gender symbol.

NoteThe Building Regulations state clear requirements for toilet facilities for disabled people.Section 8 lists the products required. We recommend the use of a delayed action doorcloser on a disabled toilet door.

Fire rated doors would require a door closer and “Fire door keep shut” signage but toiletdoors are not usually fire rated.

For details of bathroom snib turns and emergency releases, please see Bathroomaccessories, Section 9.


Examples


Lock functions

deadlock – secure

FunctionKey operates bolt from outside. Can havekey or turn operation from inside (seecylinder options, Section 5.2). Bolt throw is20mm with single turn of the key.

UsageCorridor, store, entrance and lockable lobbydoors where a pull handle/push platecombination is being used. Can also beused on duct doors.

Inside Edge Outside

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop, 1 pull handle, 1 push plate,2 kicking plates, 2 “Fire door keep shut” symbols*.

Ancillary hardware (leaf & a half, with plain meeting stile)3 pairs of hinges, 1 Fig.1 door closer*, 1 flush bolt set, 2 door stops, 1 pull handle,1 push plate, 4 kicking plates, 4 “Fire door keep shut” symbols*.

Ancillary hardware (double door, with plain meeting stile)3 pairs of hinges, 2 Fig.1 door closers*, 1 flush bolt set, 2 door stops, 2 pull handles,2 push plates, 4 kicking plates, 4 “Fire door keep shut” symbols*.

Floor springs are available as an alternative to door closer(s) and hinges (see Section 5.4).For double action doors specify push plates both sides or back-to-back pull handles.

* It is usually required that fire rated doors be self-closing and have the appropriate firedoor signage. Non-fire rated doors need not have either of these items.

Examples


Contents

• Care and maintenance

• Introduction

• Flush bolts

• Floor sockets

• Barrel boltsStraightNecked

• Heavy duty bolt

• Mortice bolt with knob turn

• Door chain

Care and MaintenanceCare and maintenance are importantfactors in ensuring that Allgood Hardwaremaintains the high quality finish for manyyears to come, and that workingcomponents give trouble-free operation.The frequency of maintenance will dependon the amount of use.

FixingsAll Allgood Hardware items are fixed usingPozidriv/Supadriv screws and the correctscrewdrivers must be used. Ask for AllgoodHardware XX5321/2/3 drivers. Do not usePhillips drivers as they are not compatible.

Bolts and floor sockets


Introduction to bolts and floor sockets

A bolt is defined simply as any lockingdevice that is not operated by a key.

Allgood Hardware includes an extensiverange of flush bolts and surface mountedbarrel bolts, all of which are covered by theAllgood 10 year guarantee.

Many are available in the full range ofmetallic and Spectra colour coated finishes– 90 colours are available as standard – tocomplement the aesthetics of any interior.

This section also provides details of easyclean and dirt excluding floor sockets tosuit the Allgood Hardware range of bolts,and the classic leather covered door chain.



25

8

2238

13

14150

72

28

2521

35

22

7010150 x 25mm lever action flush bolt with‘dovetail’ shaped return, and flange toconceal mortice.

Finishes: SC • PC • MA • TA • PB • PZ

7010/0QComplete bolt set, comprising 2x7010bolts, 7051 easy clean floor socket andintumescent pack for FD30 and FD60 firedoors.

Finishes: SC • MA • PC • PZ

7010/2QComplete bolt set, comprising 1x7010 and1x7012 bolts, 7051 easy clean floor socketand intumescent pack for FD30 and FD 60fire doors.


7010/3QComplete bolt set, comprising 1x7010 and1x7013 bolts, 7051 easy clean floor socketand intumescent pack for FD30 and FD 60fire doors.




25

8225

72

13

14

35

22

2238

28

2521



7012/2QComplete bolt set, comprising 2x7012bolts, 7051 easy clean floor socket andintumescent pack for FD30 and FD 60 firedoors.


7012/3QComplete bolt set, comprising 1x7012 and1x7013 bolts, 7051 easy clean floor socketand intumescent pack for FD30 and FD60fire doors.






25

8300

72

13

14

35

22

2238

28

2521

7013/3QComplete bolt set, comprising 2x7013bolts, 7051 easy clean floor socket andintumescent pack for FD30 and FD60 firedoors.




Finishes: AS • PBSatin nickel plated – XX48800.4 (full ref.)Polished chrome – XX48800.5 (full ref.)Colour coated aluminium – XX48800C (full ref.)

19

25

203

11

14

38

20

48800Single 203 x 19mm lever action flush bolt.Supplied with flat strike plate.

48800/QComplete bolt set, comprising 2x48800bolts, 7051 easy clean floor socket andintumescent pack for FD30 and FD60 firedoors.

Finishes: MA • PC

XX48800/0QAs above, with satin nickel plated finish.

XX48800/1QComplete bolt set, comprising 1xXX48800and 1xXX48801.4 bolts, 7051 easy cleanfloor socket and intumescent pack for FD30and FD60 fire doors.Satin nickel plated.

XX48800/2QComplete bolt set, comprising 1x48800 and1xXX48802.4 bolts, 7051 easy clean floorsocket and intumescent pack for FD30 andFD60 fire doors.Satin nickel plated.



19

25

457

11

14

38

20

XX48801.4457 x 19mm lever action flush bolt.Supplied with flat strike plate.Satin nickel plated finish.

19

25

609

11

14

38

20

XX48802.4609 x 19mm lever action flush bolt.Supplied with flat strike plate.Satin nickel plated finish

19

25

914

11

14

38

20

XX48803.4914 x 19mm lever action flush bolt.Supplied with flat strike plate.Satin nickel plated finish



25

8

300

13

14

35

22

22

20

38

28

252115

7014300 x 25 x 22mm projecting knob slideflush mounted bolt, with ‘dovetail’ shapedreturn, and flange to conceal mortice.


7018150 x 25 x 22mm projecting knob slideflush mounted bolt, with ‘dovetail’ shapedreturn, and flange to conceal mortice.


25

8

150

13

14

35

22

22

20

38

28

252115



7051Easy clean floor socket suitable for wood andstone.For use with flush bolts.

• Complete with rawlplugs

• Automatically supplied with flush boltkits


7053Dirt excluding floor socket suitable forwood and stone.For use with 13mmø flush bolts.


20

15

32

44

Finishes: PBSatin nickel plated –XX48812.4 (full ref.)Polished chrome –XX48812.5 (full ref.)

18

13

27

43

48812Dirt excluding floor socket for wood andstone.For use with 11mmø flush bolts.



6954150 x 35mm Dom straight surface bolt.

Finishes: MA • TA • PB • PC • PZ

35

11130.5

26

150 16

32

1620


Finishes: MA • TA • PB • PC • PZ35

36

26

75 16

30.5

32

1620



35

150 11130.5

35

26

300 16

32

1620



6965300 x 35mm Dom necked surface bolt.


35

150 11130.5

26

300

32

1616



11130.5

26

150

32

16

16



36

3526

75

30.5

16

20



6971Mortice bolt with knob turn.


29 29

3

47

Ø13

22.5

45

16 63.5

6972152 x 38 x 13mm door chain, with blackleather covered chain.

Finishes: MA • TA

38

152 38

1357 57

6970152 x 38.5 x 40mm heavy duty surfacebolt.

Finishes: MA • TA • PB • PC • PZ 38.5

12.5

19.5

9.5

9.525

5.5

5.5152 19

1912.5

19


Contents


• Introduction

• Concealed Newton Bearing hingesFor timber doorsFor metal doorsPower transfer hinges (for use withaccess control equipment orelectromagnetic door controls)Fixing instructions for power transferhinges

• Rising and falling butt hinges

• Butterfly butt hinges

• Pivot set and emergency release door stop



Hinges


Introduction to hinges

Allgood Hardware hinges, where specifiedcorrectly to the recommendations of BS EN1935, are capable of withstanding a severedegree of use. Most are particularlysuitable for use with door closers and willhelp to ensure the smooth operation of thedoor. The range includes rising and fallinghinges suitable for bathrooms and toiletcubicles and a series of hinges designedspecifically for fire doors. In addition, manyare suitable for metal doors and frames.

marking of these products for theiruse on fire and escape doors is required(see Standards for Architectural Hardware).

Many Allgood Hardware hinges incorporatethe new fully concealed Newton Bearings.They never stick or seize, are totallycorrosion proof and, with the factoryapplied Teflon lubricant, are entirelymaintenance-free.

All stainless steel items are supplied withstainless steel screws for fixing to timber asstandard. Fixings for metal doors/framesare provided with the appropriate metalpattern hinges.

TolerancesPositional tolerances of holes are +/-0.1mm. All other tolerances are subject to aproduction tolerance of +/- 0.5mm.

HandingThe following hinges are handed. Thecorrect handing should be ascertainedusing the drawing below, and stated at theordering stage (e.g. 8025L or 8025R).

8025L/R, 8026L/R, 8066CT2L/R, 8066CT8L/R

Standards and PerformanceMost hinges are suitable for fire doors, areCertifire approved, marked andconform to BS EN 1935 and therequirements of PSA MOB. Allgood hingesare tested with the fixings supplied. Anysubstitution of these fixings may affectultimate performance.

All CB hinges are guaranteed for 25 years.

Hinge choice and fixing positionIt is recommended that three hinges beused on all doors. On heavy doors the loadis eventually borne by the three hinges. Onlight doors the centre hinge reduceswarping and whip. The top hinge resistsmost of the bending forces which resultfrom the door width (the leaf tends to pullaway from the frame at the top andtowards the frame at the bottom).

Where doors are not expected to warp, it isadvantageous to position the middle hingecloser to the top one, typically 200mmbelow. Doors of height above 2100mmshould have four hinges per leaf. Again,equal spacing gives maximum resistance towarping and two high and two low givesthe best load carrying ability.

Recommended hinge loadingsFor most CB hinges, the maximumrecommended load has increased by over30% to 160kg for doors up to 925mmwide.

It is rare for a newly hung door to have itsweight evenly distributed between thehinges. It is more likely that the load will beborne by one hinge which then settles to thepoint that the next hinge takes a share of theload until eventually all the hinges share theload equally.

Because, initially, all the load is on onehinge, they are rated as a single item, thetotal weight of the door being equal to therated loading.

For doors fitted with backcheck door closers,BS EN 1935 recommends that the actualdoor mass should be increased by 50%when selecting the hinge, due to the extraforces directed onto the hinges when thedoor reaches the backcheck position.However,Allgood Hardware hinges haveundergone successful testing through fivemillion cycles, with the backcheck operated onevery cycle and, as Allgood warrant theirhinges, there is no need to make the BSrecommended allowance.

Maximum door mass/BS EN Grade

40kg/7 60kg/10 80kg/11 100kg/12 120kg/13 160kg/14

8075 48293 8075BB 8067CB 8064CB

8026 8025 8066CB

8068CB

8080CB

8081CB

As door width increases so do the bendingforces on the top hinge. For this reason therecommended loading is reduced toaccommodate this extra mass. Hingesshould be set into accurate mortices toavoid hinge bind. They should also be fittedexactly vertical and in alignment with eachother.

Door width (mm) Reduction in loadcapacity

926–1050 10%1051–1150 20%1151–1250 30%

Door weight chart (weight, in Kg, per m2)

Thickness (mm) 35 45 55 65

Hollow core 10 10 10 10

Pine 14.5 16 17 21

Mahogany 22 25 28 35.5

Oak 30 34 37.5 46

Hollow metal 33 33 33 33

Left Hand (L) Right Hand (R)


Hinges

• 100 x 100 x 3mm

• Triple knuckle

• Twin concealed Newton Bearings

• Button tipped

• Jig drilled

• Grade 316 stainless steel

• Maintenance free

• Totally corrosion proof

• Smoother action than ball bearings

• Load bearing capacity to 160kg

• Certifire approved

• Satisfy test requirements to BS EN 1935Grade 14, and is marked 1121-CPD-AC001

• Compatible with backcheck door closers,i.e. the performance rating is notreduced

• Guaranteed for 25 years

• No.12x11⁄4 stainless steel screws

Finishes: SS • PS • TSBrass – XX8064CBA (full ref.)

4 7 7 1 1 4 0 14

100

100

12.5

25

25

13.5 12 12 13.5

25

12.5

12.5

8064CBConcealed twin Newton Bearing butthinges for doors up to 160kg, pair.

950

60 80 100 120 140 160

1050

1150

1250

1350

Door Mass (kg)

Door Width (m

m)

Maximum door mass and width

MARKED


Hinges

• 100 x 75 x 3mm

• Triple knuckle


• Button tipped

• For easy routing 10mm radiused cornersare available, suffix ‘R’

• Jig drilled








• Finished with softened edges



• No.12x11⁄4 stainless steel screws


4 7 7 1 1 4 0 14

100

75

12.5

25

25

10 1010 10 12.5

25

12.5

8066CBConcealed twin Newton Bearing butthinges for doors up to 160kg, pair.

950

60 80 100 120 140 160

1050

1150

1250

1350

Door Mass (kg)

Door Width (m

m)


100

75

12.5

25

25

10 1010

R=10

10 12.5

25

12.5

8066RCB8066CB

MARKED


Hinges

• 114 x 114 x 3mm

• Triple knuckle


• Button tipped

• Template drilled to ANSI 156.7 with M6x 12MT posidrive truncated undercutstainless steel machine screws




• Smoother action disc bearings

• Load bearing capacity to 160kg• Certifire approved





4 7 6 1 1 4 0 14

114

114

12.5

28.5

16 99 16

31.5

28.5

12.5

12.5

8068CBConcealed twin Newton Bearing butthinges for metal doors up to 160kg, pair.

950

60 80 100 120 140 160

1050

1150

1250

1350

Door Mass (kg)

Door Width (m

m)


MARKED


Hinges

100

75

12.5

25

25

10 1010 10

25

12.5

12.5

8080CBConcealed twin Newton Bearing butthinges for metal doors/frames up to 160kg,pair.

• 100 x 75 x 3mm

• Triple knuckle


• Button tipped

• Jig drilled for metal doors/framescomplete with M6 x 12MT posidrivetruncated undercut stainless steelmachine screws




• Smoother action disc bearings






Finishes: SS • PS • TS

4 7 7 1 1 4 0 14

950

60 80 100 120 140 160

1050

1150

1250

1350

Door Mass (kg)

Door Width (m

m)


MARKED


Hinges

• STATE HAND (e.g. 8066CT2L or8066CT2R – see pages xxx and xxx)

• Left hand shown, for clockwise closingdoors

• Twin power conductors

• Maximum 50v/5000mA per conductor

• 152mm free tails

• 100 x 75 x 3mm

• Triple knuckle

• One Concealed Newton Bearing

• Button tipped

• Jig drilled







100

75

12.5

25

25

10 1010 10 12.5

25

12.5

DOOR FRAME

8066CT2L/RLoad bearing power transfer butt hingewith concealed Newton Bearing.For doors up to 160kg, when used inconjunction with a pair of 8066CB hinges.


Hinges

• STATE HAND (e.g. 8066CT8L or8066CT8R – see over)

• Left hand shown, for clockwise closingdoors

• 8 way power conductors

• Maximum 50v/5000mA per conductor

• 152mm free tails

• 100 x 75 x 3mm

• Triple knuckle

• One Concealed Newton Bearing

• Button tipped

• Jig drilled







100

75

12.5

25

25

10 1010 10 12.5

25

12.5

DOOR FRAME

8066CT8L/RLoad bearing 8 way power transfer butthinge with concealed Newton Bearing.For doors up to 160kg, when used inconjunction with a pair of 8066CB hinges.


Hinges

Fixing Power Transfer Hinges 8066CT2/8066CT8ApplicationThese hinges have integral cables whichwill pass a current from the frame into thedoor or side panel. They are suitable for usewith any Allgood Secure access controlequipment, or electro-magnetic doorclosers. The hinges are designed specificallyfor use with standard Allgood Hardware8066CB hinges.

Technical Information

Maximum voltage: 24V.

Number of conductors: 2 (8066CT2)8 (8066CT8).

Max. current per conductor: 5A.

Cable tails: 152mm long.

Material: Grade 316 stainless steel.

Finishes: SS & PS from stock. Other finishesto order.

Fixings: Supplied with 8 x No.12 woodscrews, 8 x M6 undercut head metal threadscrews.

Handing and Positioning1. The hinges are handed and for long

term durability it is essential that thecorrect hinge is fitted and with the TOPuppermost, as shown below.

2. The hinge should be fitted as the centralhinge of a set of three, in a positionsuitable for the type of use (i.e. Option1: access control or Option 2: doorcloser).

Fixing Instructions1. The door and frame must be prepared

for the cable run to the electronichardware items and to accept the hingeflaps in the normal way.Note: the cable entry hole (10mmø) inthe frame should be approximately27mm above the cable entry hole in thedoor.

2. Fix the door to the frame with the otherload-bearing hinges and check that thedoor swings freely.

3. Check that you have the correct hand ofpower transfer hinge (see opposite).

4. Ensure that cables to the otherhardware project sufficiently to makethe connections. Using standardconnector blocks, make all thenecessary connections to the hinge fromthe door and from the frame. (The doorand frame may need to be cut awaylocally to accept the connector blocks.)

5. Feed the wires back inside the door andframe and fix the hinge with the screwsprovided, making sure no wires aretrapped behind the hinge flaps.

TOPDoorFrame Door Frame

Clockwise closing door(Left hand hinge)

Anti-clockwise closing door(Right hand hinge)

200mm

Option 1 Option 2

27 mm


Hinges

• STATE HAND (e.g. 8025L or 8025R) – left hand shown

• 100 x 77 x 3mm

• Minimum door thickness 29mm

• To ensure correct working, pairs of risingbutts must be fitted coaxially withscrews supplied

• Only 2 butt hinges for each door

• Supplied with recommended lubricant

Finishes: SS • PS • PB

100

77

8

28

28

7.56.5

6.57.5

26

19ø

16

1

28

8

8025L/RRising butt hinges for doors up to 60kg,pair



Hinges

• STATE HAND (e.g. 8026L or 8026R) – left hand shown

• 100 x 77 x 3mm

• Maximum door opening 120°

• Minimum door thickness 29mm

• To ensure correct working, pairs offalling butts must be fitted coaxially withscrews supplied

• Only two butt hinges for each door

• Supplied with recommended lubricant


77

8

28

28

7.56.5

2626

28

8

100

6.57.5 19ø

8026L/RFalling butt hinges for doors up to 50kg,pair



Hinges

• For emergency use in hospitals, nursinghomes or wherever the ill or infirm runthe risk of falling over and blocking aninward opening bathroom or toilet door

• Allows the door to swing in eitherdirection. Specifically designed for usewith the XX13005 emergency releasedoor stop

• For doors up to 44mm thick

• Bottom bracket is frame mounted butmust be floor supported when used ondoors weighing in excess of 30kg

• Medium duty assembly for interior doorsof average frequency traffic

• For doors weighing up to 80kg and up to1100mm wide

• Top and bottom door plates have oilimpreganted bronze bearings

80

6

6

6

6

5237

58

110

110

52

52

130

XX13001Double action pivot set.For emergency access to toilet cubicles.

DOOR

FLOOR

FRAME20x86x35 High Cavity


Hinges

• Stainless steel

• Stop release resets automatically

• Built-in fingertip release

• Rubber insert for quieter action

• Allows double action doors to operate assingle action when hung on centre pivots

42

25

112 96 60

203

XX13005Emergency release door stop.For use in conjunction with XX13001double action pivot set.


Contents• Care and maintenance

• Introduction

• Overhead door closersAlternative fixing brackets

• Electromagnetic release overhead doorclosers

• Transom mounting kit for Fig.1 doorclosers

• Armoured loop

• Fully concealed overhead door closers

• Adjustments for fully concealed overhead door closers

• Fully concealed transom door closers

• Floor springsCommander floor springsCavalier floor springsElectromagnetic Commander floorspringAccessories for floor springs

• Electromagnetic release fire door holdersFloor mountedWall mounted

• Selector stays

• Concealed overhead door restraining stay

Care and MaintenanceCare and maintenance are importantfactors in ensuring that AllgoodHardware maintains the high qualityfinish for many years to come, and thatworking components give trouble-freeoperation. The frequency ofmaintenance will depend on theamount of use.

FixingsAll Allgood Hardware items are fixedusing Pozidriv/Supadriv screws and thecorrect screwdrivers must be used. Askfor Allgood Hardware XX5321/2/3drivers. Do not use Phillips drivers asthey are not compatible.

Overhead door closers and floor springsThe internal mechanisms are completelyimmersed in oil and they are designedso that no maintenance is required. Theunits are also protected by overloadabuse safety valves against accidentalor deliberate misuse. Once the doorcontrol has been correctly fitted to suitlocal conditions, no further adjustmentsshould be necessary. However, afrequent check should ensure that thedoor closes freely and positively into theframe without slamming (a little lightoil or aerosol lubricant on the latch boltand arm pivot point for overhead doorclosers may be helpful) and that allfixing screws are tight.

The storage and use of door controlsshould be in dry conditions between -5°C and +40°C. The shelf life isindefinite within the guarantee period.

Warning: Door controls containpowerful springs which are inserted intothe body under pressure and should notbe removed except by the manufacturer.

Door controls & stays


Introduction to door controls

Door controls are placed under morearduous conditions of use and abuse thannearly all other items of hardware. It isessential that their operation is smooth,efficient and reliable at all times, especiallywhen used on fire resistant and smokecontrol doors.

Allgood Hardware door controls areproduced to the highest standards ofdesign and most have adjustable controlfeatures. Allgood plc is a leading UKsupplier of adjustable backcheck overheaddoor closers including versions that haveCertifire approval, and every AllgoodHardware door control carries a 10 yearguarantee.

These devices are marked. Please askfor our Declaration of Conformity, or visitour website (www.allgood.co.uk). The ECCertificate of Conformity for them is1121-CPD-AD0001.

All door controls are manufactured infactories holding accreditation to theBS EN ISO 9001 2000 Quality ManagementSystem.

OVERHEAD DOOR CLOSERSMost closers are to BS EN 1154:1997 (seemain Introduction, Standards forArchitectural Hardware) and Certifireapproved.

Door closers are available in the full rangeof metallic and Spectra colour coatedfinishes.

Configuration of Door Closers

FLOOR SPRINGSAllgood Hardware floor springs areconstructed to the highest specification andare available in single and double actionoptions.

The slimline Commander and Cavalier rangesof floor springs incorporate many uniquefeatures to ensure easy installation andadjustment as well as providing attractiveaesthetics and long-term reliability.

The ranges include double action andcentre pivoted single action floor springsfor internal and external doors: a multi-functional adjustable power (1 to 6) unit, amechanical hold-open version and anelectromagnetic hold-open model. Floorsprings feature fully adjustable housing toallow fine setting of door alignment andfully adjustable closing speed and aproportional backcheck action at 90°.Commander unit installation is achieved bya unique micro-adjustable toe-in andcentering control and a built-in levellingdevice. Satin stainless steel grade 316cover plates are fitted as standard. Allother metallic and Spectra finishes areavailable.

FIRE DOOR CONTROLSMechanical hold-open devices whichpermanently hold a door open untilphysically released are unsuitable for useon fire resisting doors. Electromagneticrelease closers, however, hold openelectrically and, when connected to acentral fire-alarm system, will allow thedoor to close automatically in the event ofsupply failure or alarm activation.

All Allgood Hardware door releases are‘fail-safe’. The door will be released andclose immediately when the alarm is setoff, either manually or by the automaticsmoke or heat sensitive devices. The doorwill also be released and closedautomatically in the event of power failure.The door can always be closed manually.

SpecificationFire door holders 9408 and 9409 must beused in conjunction with an overhead doorcloser or floor spring. In principle, to avoiddistortion of the door, the release deviceshould be positioned at the same height asthe door closing device.

Integral hold/release mechanisms (9431/4,9451 and 9461) have an advantage overstandard closing devices combined withelectromagnetic door releases, since theydo not induce any twisting forces to thedoor which can lead to warping of woodendoors after prolonged use.

RegulationsElectromagnetic release and swing freedoor closing devices are accepted by FireOfficers and local authorities and complywith the 1991 Building RegulationsApproved Document B, 2000 Edition,Appendix B.

Maximum door mass/widthThe table below shows the door massesand widths as contained in the BS EN 1154European Standard.

Table 1 (from BS EN 1154)Power size of door control Max. mass of hinged leaf Width of door leaf

1 20kg <750mm2 40kg 850mm3 60kg 950mm4 80kg 1100mm5 100kg 1250mm6 120kg 1400mm7 160kg 1600mm

However, Allgood Hardware floor springswill carry door masses up to 250kg (singleaction) and 400kg (double action) whenfitted with the standard height spindle.

Figure 1

Figure 6


Overhead door closers

Fitting to opening face of door (Fig.1). Integralintumescent protected soffit fixing plate.

Power: adjustable EN Power 2–4.

Max. door mass/width: see Introduction.

Closing speed: fully adjustable and withindependent latch action.

Backcheck: fully adjustable angle ofoperation, 60°–130°. To limit the openingangle, a doorstop is recommended.

Opening angle: up to 180°.

Fixings: single fixing position. Concealedscrews for wood or metal. Special brackets/plates for metal doors/frames readily availableto order. For internal and external doors.

9151ASO – Hold-open version: push doorapproximately 3° past the 90° holdingposition and release; the door will moveback to the 90° position required (not forfire door use).

9151ADC – Delayed closing version withminimum 20 second delay between 65°and 90°. Maximum 45 seconds.

Standards performanceIndependently tested and complies withthe requirements of BS EN 1154:1997

with backcheck and is marked 1121-CPD-AD0001 (see Standardsfor Architectural Hardware in the mainIntroduction). Has been included in manysuccessful 3rd party tests on fire doorassemblies to BS EN 1634-1and BS 476 Pt22 up to 120 minutes on timber doors andis Certifire approved, for use on certainlatched and unlatched assemblies andsingle and double doors. UL listed.

Finishes: MA • TA • PB • PCSatin stainless steel plated –XX9151ASS (full ref.)

4 8 2 /4 1 1 3

9151AHeavy duty overhead door closer with fullyadjustable power and adjustablebackcheck, as well as latching and speed.

50

48 290

273

123

27

160

24

MARKED



Fitting to closing face of door (Fig.6).






Fixings: single fixing position. Concealedscrews for wood or metal. Special brackets/plates for metal doors/frames readily availableto order. For internal and external doors.

9156ASO – Hold-open version: push doorapproximately 3° past the 90° holdingposition and release; the door will moveback to the position required (not for firedoor use).

9156ADC – Delayed closing version withminimum 20 second delay between 65°and 90°. Maximum 45 seconds.

Standards performanceHas been independently tested andcomplies with the requirements ofBS EN 1154:1997 withbackcheck and is marked1121-CPD-AD0001 (see Standards forArchitectural Hardware in the mainIntroduction). Has been included in manysuccessful 3rd party tests on fire doorassemblies to BS EN 1634-1 and BS 476 Pt22 up to 120 minutes and is Certifireapproved, for use on certain latched andunlatched assemblies and single anddouble doors. UL listed.

Finishes: MA • TA • PB • PCSatin stainless steel plated –XX9156ASS (full ref.)

4 8 2 /4 1 1 3

50

48 290

9156AHeavy duty overhead door closer with fullyadjustable power and adjustablebackcheck.

273

93

21

27

50

180

Underside of headframe

Hingecentreline

MARKED



Fitting to opening face of door (Fig.1).Suitable for up to 4 hour fire doors. Forinternal and external metal doors. Non-flammable hydraulic fluid.






Fixings: single fixing position. Concealedscrews for wood or metal. Specialbrackets/plates for metal doors/framesreadily available to order.

Please Note: No hold-open version isavailable.

Standards performanceHas been independently tested andcomplies with the requirements ofBS EN 1154:1997 .Has been included in many successful 3rdparty tests on fire door assemblies toBS 476 Pt 22 up to 240 minutes and isCertifire approved, for use on certainlatched and unlatched assemblies andsingle and double doors. UL listed.

Finishes: MA • TA • PB • PCSatin stainless steel plated –XX9151ASF (full ref.)

4 8 2 /4 1 1 3

9151AFFHeavy duty overhead door closer with fullyadjustable power and adjustablebackcheck. For steel fire doors.

50

48 290

273

123

27

160

24



Fitting to closing face of door (Fig.6).Suitable for up to 4 hour fire doors. Internaland external metal doors. Non-flammablehydraulic fluid.






Fixings: single fixing position. Concealedscrews for wood or metal. Special brackets/plates for metal doors/frames readilyavailable to order. For internal and externaldoors.

Please Note: No hold-open version isavailable.

Standards performanceHas been independently tested andcomplies with the requirements ofBS EN 1154:1997 .Has been included in many successful 3rdparty tests on fire door assemblies toBS EN 1634-1 and BS 476 Pt 22 up to 240minutes and is Certifire approved, for useon certain latched and unlatchedassemblies and single and double doors. ULlisted.

Finishes: MA • TA • PB • PCSatin stainless steel plated –XX9156ASF (full ref.)

4 8 2 /4 1 1 3

9156AFFHeavy duty overhead door closer with fullyadjustable power and adjustablebackcheck. For steel fire doors.

50

48 290

273

93

21

27

50

180

Underside of headframe

Hingecentreline



9156FNAlternative fixing bracket.

21

31.54565

102.5

9151FNAlternative fixing bracket.

Alternative opening face fixing bracket for9151A, 9151AFF, 9171, 9451 and 9461door closers.

Finishes: SC • PC • MA • TA • PB

Fixing instructions1. Fix the closer as instructed.

2. Position the face fixing bracket asshown on the template.

3. Join the arm to the bracket with thebutton and pivot pin provided.

25

20 (to topof pin)

50

32.5

16

Alternative face fixing bracket for flushframe for 9156A, 9156AFF, 9176, 9456 and9466 door closers.

Finishes: SC • PC • MA • TA • PB

Fixing instructions1. Fix the closer as instructed.

2. Position the face fixing bracket asshown on the template.

3. Join the arm to the bracket with thebutton and pivot pin provided.



9471Surface mounted armoured loop.

To simplify installation a surface mountedarmoured loop is available to carry thepower from the door frame to the doorcloser unit. Can be used with 9451/9461and 9456/9466 electromagnetic releasedoor closers.

For timber and metal door frames.

Concealed loop (XX79053 – see SecureSection 7.7) and power transfer hinges(8066CT2 and 8066CT8 – see Hinges Section 5.5) are alsoavailable.

Finishes: MA • TA • PB • PCSatin stainless steel plated –XX9471SS (full ref.)

9472Transom mounting kit for 9151A, 9151AFFand 9171/6 door closers, and 9451electromagnetic release door closer.

Adjustable arm suits frame projectionsfrom 0–80mm.

Finishes: MA • TA • PB • PCSatin stainless steel plated –XX9472SS (full ref.)

0–80mm


Floor springs

9231Commander multi-functional floor springcomplete with accessories (seeAccessories).

Adjustable power (2–6) to BS EN 1154,adjustable closing speed, proportionalbackcheck, levelling device and centringadjustment and micro-adjustable toe-in.With box, 60mm deep.

Max. door mass/widthAll floor springs will carry door masses upto 250kg (single action) and 400kg (doubleaction). Note: stand open version notsuitable for use on fire doors.

Standards performanceCertifire listed and independently assessedto BS EN 1154 and is marked 1121-CPD-AD002.

Incorporated in successful fire tests andassessed to BS 476 Pt 22 120 minutes andBS EN 1634.

For single action doors, specify:16mm offset 9231S616mm offset ‘stand open’ 9231S6S25mm offset 9231S525mm offset ‘stand open’ 9231S5S

For double action doors, specify:9231D

‘Stand open’ 9231DSO


To prevent moisture entering the box,specify XX9231XG gel pack, which sealsthe floor spring unit in the floor box.

4 8 1/6 1 1 3

60

45/51

307 78

MaintenanceThe integral mechanism of the floor springis immersed in oil and has been designedso that it requires no maintenance. It isprotected from misuse by an overloadsafety feature. On no account should anyattempt be made to dismantle a floorspring, since it contains a pre-stressedspring which could be dangerous.

Once the floor spring has been installedand adjusted to suit local conditions, nofurther maintenance should be necessary.However, an annual check should ensurethat:

a) the door leaf closes freely and positivelyinto its frame from any angle withoutslamming.

b) all fixing screws to the unit andaccessories are tight.

TestingTo ensure that the floor spring meets therequirements of the Building Regulations1991 Approved Document B, 2000 Edition,Appendix B, it has to be capable of closingthe door leaf from any angle against anylatch fitted.

To test this, open the door to its maximumopening angle and release. The door leafshould close fully into the door frame andovercome any latch or seals.

Any failure to close the door leaf should beinvestigated. It may indicate that the powerof the floor spring requires adjustment orthat excessive force is required to close thedoor leaf, due to distortion ormisalignment.

MARKED


Floor springs

9247Cavalier adjustable power floor springcomplete with accessories (seeAccessories).

Adjustable fixed power (1–4) toBS EN 1154, adjustable closing speed, fixedbackcheck. With box, 50mm deep.


Standards performanceCertifire listed and independently assessedto BS EN 1154 .

Incorporated in successful fire tests andassessed to BS 476 Pt 22 120 minutes andBS EN 1634.

For single action doors, specify:16mm offset 9247S616mm offset SO 9247S6S25mm offset 9247S525mm offset SO 9247S5S


SO 9247DS


To prevent moisture entering the box,specify XX9231XG gel pack, which sealsthe floor spring unit in the floor box.

4 8 1/4 1 1 3

50

45/51

307 78

MaintenanceThe integral mechanism of the floor springis immersed in oil and has been designedso that it requires no maintenance. It isprotected from misuse by an overloadsafety feature. On no account should anyattempt be made to dismantle a floorspring, since it contains a pre-stressedspring which could be dangerous.

Once the floor spring has been installedand adjusted to suit local conditions, nofurther maintenance should be necessary.However, an annual check should ensurethat:a) the door leaf closes freely and positively

into its frame from any angle withoutslamming.

b) all fixing screws to the unit andaccessories are tight.


To test this, open the door to its maximumopening angle and release. The door leafshould close fully into the door frame andovercome any latch or seals.



Floor springs

9431Commander electromagnetic floor springcomplete with accessories (seeAccessories).

Commander electromagnetic floor spring,24vDC / 2.8W. Fixed power 4. With micro-adjustable toe-in and unique levellingdevice. With box, 60mm deep and cable 3metres long.

The unit will hold at any angle to which itis opened beyond 75°. Note that the holdopen angle may be up to 5° less. Toelectrically release, it is recommended thata test button is located nearby.

To mechanically release, simply pull thedoor towards the closed position. TheCommander electromagnetic floor spring isfail safe; in the event of a power failure,the unit will automatically close.


Standards performanceCertifire approved and independentlyassessed to BS EN 1155 andis marked 1121-CPD-AE002.

For single action doors, specify:16mm offset 9431S625mm offset 9431S5



Power supply: 24v DC.

3 8 4 1 1 3

60

45/51

307 78

MaintenanceThe integral mechanism of the floor springis immersed in oil and has been designedso that it requires no maintenance. It isprotected from misuse by an overloadsafety feature. On no account should anyattempt be made to dismantle a floorspring, since it contains a pre-stressedspring which could be dangerous.Once the floor spring has been installedand adjusted to suit local conditions, nofurther maintenance should be necessary.However, an annual check should ensurethat:a) the door leaf closes freely and positively

into its frame from any angle withoutslamming.

b) all fixing screws to the unit accessoriesare tight.


To test this, open the door to its maximumopening angle and release (with powerremoved). The door leaf should close fullyinto the door frame and overcome anylatch (single action only) or seals.


MARKED


Floor springs accessories (inclusive)

Cover plates for double action floor spring.

Finishes: SS • PS • TS • PB

105

32

323

165

Cover plates for 16mm and 25mm singleaction floor springs.

Finishes: SS • PS • TS • PB

105

323


Floor springs accessories (inclusive)

Single action strap shoe and top centrewith intumescent protection for use withCommander and Cavalier floor springs.Cast 316 stainless steel with integralintumescent protection. Non-handed.

Single action offset strap and top centre.16mm offset.

39

22

8

8194

194

194

Top centre

Strap

Strap cover

3°

8

39

22

30mm ø

22

16

16

Single action strap shoe and top centrewith intumescent protection for use withCommander and Cavalier floor springs.Cast 316 stainless steel with integralintumescent protection. Non-handed.

Single action offset strap and top centre.25mm offset.

48

48

22

8

3°

8194

194

194

Top centre

Strap

22

25

25

22

8

Strap cover

30mm ø

Double action strap and adjustable topcentre for Commander and Cavalier floorsprings. Forged steel with integralintumescent protection.

Top centre allows use within shallow headdetail of 42mm, even when pin is in theraised position.

Double action strap and top centre.

32 23

8

200

40

Top centre

Strap

40

166

200

32

34

42

2164

8

23

18

18


Floor springs accessories (optional)

XX9231SPExtension spindle for Commander and Cavalier floor springs.

The standard clearance between the floorand the underside of door is 8mm.Extended spindle inserts are available toachieve clearance over thresholds, carpets,computer pans etc. (See drawing and usechart below.)

STATE DEPTH:Depth Full Product No. Door

Clearance ‘X’10mm XX9231SP10 18mm20mm XX9231SP20 28mm30mm XX9231SP30 38mm40mm XX9231SP40 48mm50mm XX9231SP50 58mm

X

DOOR

9231POverhead pin stop with rubber buffer forcentre pivoted single action doors.

• Suitable for hardwood frames only

Finishes: SS • PS

40

13

9249Heavy duty floor pivot set with thrust rollerbearing, complete with forged 316stainless steel straps, integratedintumescent protection and 316 stainlesssteel covers.

400kg load capacity.Extended spindle height available tospecial order.

9249CD – Double action9249CS5 – Single action 25mm offset9249CS6 – Single action 16mm offset


45 28

156 4

28

ø40

92

21 50


Selector and restraining stays

75 x 57 x 170mm door selector stay withgravity arm. Suitable for use on wood andmetal fire doors. Ensures correct closingsequence. The door selector will only allowthe stiles to close in the correct ordermaintaining the fire resistant seal.

Standards performanceHas been tested and complies with therequirements of BS EN 1158 and achievedthe following classification , and included in successful 3rd party firetests on fire door assemblies to BS 476 Pt22, up to 120mins. Certifire approved CF349 and marked 1121-CPD-AF0001.

Finishes: SS • MA • TA • PB • PC

57

50103

63

4541

Leaf ‘A’ Leaf ‘B’

9149GSelector stay for pairs of rebated doors.

XX11004Concealed overhead door restraining stay.

• Stainless steel arm and aluminiumchannel and bracket with adjustablefriction slide block and spring buffer tocushion door opening

• Friction can be adjusted to enable thestay to be used in conjunction with asurface mounted overhead door closer

• Not for use with concealed door closingdevices

• Can be fitted to set the maximumopening to 70°, 90° or 110°

93

17.5 16495

3 5 3/5 1 1 0


Floor mounted automatic operators

71961Single floor mounted operator. For use withleft handed doors, opening in (see below).Complete with 71999 safety sensors and71999CO safety sensor cut out switch.Stainless steel finish.

• Allgood Secure’s revolutionary floormounted automatic operator series. Idealfor automatic operation of doors whereaesthetics is of major importance.

• Designed for heavy-duty usage on mostinternal or external, single or double, leftor right handed doors. This includesdesignated fire doors and, whenspecified in conjunction with thenecessary safety devices, the unit willmeet the requirements of the BritishStandard for powered doors (BS7036).

• In combination with the Allgood Securerange of actuators and safety sensors,the automatic operators are capable ofmeeting the most demanding ofsituations.

• Floor mounted unit, suits all standarddoor materials – timber, steel, aluminiumand glass.

• Doors can still be opened manually evenwhen the drive is switched on and in theevent of of a power failure.

• Closing speed, power, latch action,opening angle and hold open time areall adjustable.

• Power – single phase 230v AC 50Hz.

• Maximum door size – weight: 140kg /width: 1400mm / height: 2400mm. Forheavier doors please contact AllgoodSecure.

• Allgood Secure floor mounted automaticoperators are only to be supplied andinstalled by Allgood Secure engineers.

• Pivot and straps supplied separately.

71962As above, but for use with left handeddoors, opening out (see below).

570

210

135

54

OUTSIDE

INSIDE

OUTSIDE

INSIDE

Actuation of automatic door operators maybe achieved by use of any of the AllgoodSecure access control systems in Section6.1 or by the units shown above. A threeposition keyswitch is available to allow anautomatic door operator’s controlswitching to be remotely positioned. Pleasenote that these items should be carefullyspecified to avoid conflict with otherhardware items such as safety sensors.


Floor mounted automatic operators

71963Single floor mounted operator. For use withright handed doors, opening in (see below).Complete with 71999 safety sensors and71999CO safety sensor cut out switch.Stainless steel finish.

71965Double floor mounted operator. For usewith double doors opening in (see below).Complete with 71999 safety sensors and71999CO safety sensor cut out switch.Stainless steel finish.

71967Finger guard. Prevents trapping of fingersduring closing sequence. Can also be usedto truncate cabling.• Suitable for glass door and side panel.

Template must be provided to doormanufacturer.

71964As above, but for use with right handeddoors, opening out (see below).

71966As above, but for use with double doors,opening out (see below).

570

210

135

54

OUTSIDE

INSIDE

OUTSIDE

INSIDE

OUTSIDE

INSIDE

OUTSIDE

INSIDE


Safety sensors, actuators and accessories

71995Standard radar unit.

71999Opening face safety sensor.

122

82

103

42

50

• Safeguards area within opening swingradius of automatic swing leaf door.Operation of door stops as soon as anobstruction is detected within zone ofsensor.

• Compatible with Allgood Secureautomatic door operators.

• Normally specified in conjunction withclosing face safety sensor. Safety sensorsenable compliance with BS7036.

71999COSafety sensor cut out switch to be used inconjunction with electronic locking.

71996Elbow push pad.

• Used in conjunction with, or asalternative to, radar units to preventnormal pedestrian traffic causing falseactuation.

• Cream plastic finish.

71997RAFinger guard.

• Prevents trapping of fingers duringclosing sequence.

• Suitable for 70mm stile width.

• For single doors only.

• Aluminium finish.

71996SS150mm diameter circular satin stainlesssteel push pad.

Used in conjunction with, or as alternativeto, radar units to prevent normal pedestriantraffic causing false actuation.

71997RBAs above, but with bronze finish.

71996BTAs above, but powder coated in BioCote –the latest anti-bacterial technology thatoffers an extra level of protection againstaccumulating infectious bacteria. For moreinformation , please refer to Finish Section2.1.

79230Touchless sensor/exit switch.

81

81

418

65ø

• Adjustable operating field of between10–50cm avoiding the need for contactwith hands to operate, guaranteeingabsolute hygiene.

• Detects persons anywhere within anadjustable field of scan.

• Weatherproof cover available forexternal locations.

• Black plastic finish.


Contents


• Introduction

• Heavy duty

HL72’ modular locks

• Severe duty

HD99’ Redlocks

• Medium duty

Introduction

73’ cylinder locks

75’ cubicle & claw bolts

82’ narrow stile lock

83’ cylinder rim nightlatches

Katkin access panel lock

• Fixing instructions for rebate components

• Padlocks – refer to Cylinders Section 5.2



ConfigurationsAll Allgood configurations lever sets orQuadaxial levers should be fitted using theXX9561 Quadaxial tool kit (see Section5.7).

Lock cases and strikesCheck that all fixings are fully tightened,and check that latchbolt enters the strikesmoothly and adjust if required. Ensurethat the frame mortice allows for deadboltto be fully operated. Apply aerosol lubricantinto the case around the latchbolt anddeadbolt at regular intervals. Werecommend ‘WD40’ or a PTFE lubricant.

CylindersIt is essential that only special aerosollubricant XX9568 be used in and aroundthe cylinder, cylinder and turn and the key.

Locks and Latches


Introduction to locks and latches

The Allgood Hardware range of locks andlatches cover all the standard securityrequirements of a building.

Allgood Hardware locks and latches areavailable in cylinder and lever versions,cover all functions and include padlocks(see Cylinders) and cylinder rimnightlatches.

HEAVY DUTY LOCKS AND LATCHESHL72’The HL72’ Modular Lock System is a fullsuite of heavy duty mortice locks andlatches designed to support the entireAllgood range of levers, knobs and otherunsprung furniture.

SEVERE DUTY LOCKS AND LATCHESHD99’ RedlocksWith fire safety and security in mind,Allgood have designed the HD99‘ Redlocks.The range is particularly suitable for severeusage doors and where a higher degree ofsecurity is required.

MEDIUM DUTY LOCKS AND LATCHES73'73’ is a selected range of the most popularlatch/lock functions. designed tocomplement 72’ in dimensional layout.73’ provides a cost-effective alternative.

75’ cubicle bolt & claw bolt75’ are compact lock cases specifically foruse on sliding or bathroom doors.

NARROW STILE LOCK, RIM NIGHT-LATCHES AND ACCESS PANEL LOCK82’Narrow stile mortice deadlock

83’Cylinder rim nightlatches

Katkin access panel lock

Cylinder locks are supplied case only,complete with cylinder screw of correctlength for the lock. For cylinders andmaster keying, see the Cylinders section.

Each series is based on standard case sizes,allowing simplified door preparation.

Many of the models have alternativebacksets – either to place the lever handlefurther from the door edge, for aestheticreasons, or to accomodate knob furniture.

All locks and latches are heavily sprung forlever handles or softly sprung for knobfurniture.

Most deadbolts have hardened stainlesssteel anti-saw pins for added security.

Latchbolts can easily be reversed withoutremoving the lock case cover, so the samelock or latch can be specified whatever theclosing direction of the door.

Locks generally are packed 1 per box,complete with screws and fixinginstructions/template.

Rebate components are available for allmortice locks, apart from the 82’ deadlock,in 13mm, 19mm and 25mm sizes, and aresuitable for either hand.

Most Allgood Hardware mortice locks andlatches allow for bolt through fixings forlever handles and roses, and forescutcheons on cylinder/bathroom locks.

It is important to check before fixingwhether the holes for furniture and/orkeyhole or cylinder are required on one orboth sides of door. When using a handle onone side only, specify the XX9052NT halfspindle.

Performance standardsFor the latest information, please visitwww.allgood.co.uk.

Allgood 72’ locks & latches have beentested to all the requirements ofBS EN 12209 and where appropriateEN 179.

Many Allgood Hardware locks & latcheshave been incorporated in successful firetests to BS EN 1634-1, BS476 Part 22 andUL10B.

Allgood Hardware was included in the PSAMethod of Building Programme, 3rdEdition: MOB H3 01.

Every Allgood Hardware mechanical productcarries a 10 year guarantee.

TolerancesAll dimensions given are subject to aproduction tolerance of ±0.5mm.

DisclaimerAlthough all the information and details inthis brochure are given in good faith, themanufacturers do reserve the right tochange the products’ specifications withoutnotice.


Heavy duty locks and latches

HL72’HL72’ Modular Lock System is a full suiteof heavy duty mortice locks and latchesdesigned to support the entire Allgoodrange of levers, knobs and other unsprungfurniture. The range is suitable for generalcommercial and heavy industrial use.Offering complementary build quality,design integrity, and choice of externalfinishes, HL guarantees the perfect matchbetween form and function whenever youspecify Allgood architectural ironmongery.

• A full suite of heavy duty Euro profilecylinder mortice locks and latches – tosuit all Allgood lever and knob furniture.

• Modular case sizes – for easier doorpreparation.

• Rebate conversion sets are available for13, 19 and 25mm rebate depths ondouble doors – to allow locks to befitted in most rebated door sections.

• Latchbolts are easily reversible withoutusing tools or removing the lockcasecover – non-handed locks simplifyspecification and save time on site.

• Reversible strike plate.• Low friction latchbolts – give smoother

and quieter locking action and reducedamage to the door and frame.

• 20mm single throw deadbolts (exceptthe 7208 and 7225 bathroom locks) –provide greater security.

• Recent comparison tests between otherranges show that this lock design hasthe easiest latching force of all typestested. This makes it ideal for doorswhere smoke seals are fitted enablinghigh closing efficiency and ease ofaccess for e.g. the disabled. In addition,high efficiency closers complement thefitting of smoke/acoustic seals and allowreduced opening and closing forces to beachieved.

• Unique Griptight followers – preventmovement of the spindle within thefollower, thus eliminating erroneousmovement of lever handles.

• Solid stainless steel latchbolts, deadboltsand followers – provide enhanceddurability and security.

• High quality springs in locks and latchesfor lever handles – provide enhancedcorrosion resistance, durability andprevent lever handles from sagging.

• Two way soft action mechanism in locksand latches for knob furniture – allowseasy and convenient operation.

• Bolt through holes are provided for rosesand/or escutcheons on all locks andlatches.

• All locks and latches are available withthree different backsets – 60mm asstandard for levers, or 80mm to placethe lever handle further from the dooredge, for aesthetic reasons, or 100mm toaccomodate knob furniture.

• Radiused forends and strikes areavailable to allow router pre-preparation of doors and frames in thefactory, saving time.

• Forends and strikes are available invarious metallic finishes – to match thefine aesthetics of associated Allgood doorfurniture. Forends are available in Spectracolours – 90 colours are available asstandard.

• Supplied with pre-formed strike – forease of installation and to provideconsistent door closing forces.

• Fixing screws are provided (Type AB self-tapping) – suitable for both timber andmetal.



7204Vertical mortice latch.

102

38

11

b

a

16521.5

4631

42 24

9 9

24

25 22

16

13.5

145 235 233206 209235

20

Case sizesRef. No. Handle Forend a b7204.60 Lever Square 92 607204.80 Lever Square 112 807204K10 Knob Square 132 1007204F60 Lever Radius 92 607204F80 Lever Radius 112 807204KF10 Knob Radius 132 100

• Three modular case sizes – see table below

• Latchbolt– reversible without using tools or

removing lockcase cover

• Unique Griptight follower

• High quality springs in latch for leverhandles

• Two-way soft action mechanism in latchfor knob furniture (i.e. locks with 100mmbackset)

• 60mm backset options Certifireapproved, CF 347

• 60mm backset options to BS EN 12209

• Forend and strike plate– option of square or radius– range of metallic finishes– forends available in Spectra colours– pre-formed strike plate– reversible strike plate

• Type AB self-tapping fixing screwsprovided – suitable for both timber andmetal

• Bolt through fixing holes for levers

• When using a handle on one side only,specify the XX9052NT half spindle

• Rebate conversion set 7245 available forthis latch – specify 13mm, 19mm or25mm

Finishes: SS • PS • TS • PB • PZ

3 X 8 1 0 F 1 B 0 3 0



7208Vertical mortice bathroom lock.

78

38

11

b

a

165

12

21.5

4631

35

42 24

24

25 22

145 235 233206 209235

16

13.5

11

9 9

20

Case sizesRef. No. Handle Forend a b7208.60 Lever Square 92 607208.80 Lever Square 112 807208K10 Knob Square 132 1007208F60 Lever Radius 92 607208F80 Lever Radius 112 807208KF10 Knob Radius 132 100

• Three modular case sizes – see table below

• Deadbolt– 12mm

• Latchbolt– reversible without using tools or

removing lockcase cover


• 78mm centres





• Bolt through fixing holes for levers andturn/emergency release

• Rebate conversion set 7245 available forthis lock – specify 13mm, 19mm or25mm




7225Lift to lock (L2L) Easy Action privacy lock.Specify 7225ASS for full assembly ofnecessary components (see facing page).

78

38

11

60

92

165

12

21.5

4631

35

42 24

24

25 22

145 235 233206 209235

16

13.5

11

9 9

20

The 7225 “L2L” Easy Action privacy lock andcomponents are specially designed and uniqueto Allgood.The installation is visually clean andsimple to use. This hardware is particularlysuitable for bathrooms and similar situationswhere it is desirable to lock the door easilyfrom the inside. Other examples of use arelaboratories, darkrooms, bedrooms etc.

The inside lever has a dual function. Whenlifted up it simultaneously locks the externallever and actuates the external indicator. Thevertical position of the locked lever veryclearly indicates that the door is indeedlocked. Depressing the inside lever withdrawsboth bolts and resets the indicator.

A Modric external indicator and emergencyrelease should be used. Any Allgood levermay be specified.• Deadbolt

– 12mm

• Latchbolt– reversible without removing lockcase

cover


• 78mm centres




• Type AB self-tapping fixing screws provided– suitable for both timber and metal

• Bolt through fixing holes for both leversand cylinder

• Rebate conversion set 7245 available forthis lock – specify 13mm, 19mm or 25mm




7225 InstructionsFunctionThe 7225 Lift to lock easy action privacylock is operated by a lever from both sidesof the door but unlike normal locks onelever is higher than the other. The top leveroperates the latch and is always fixed tothe outside face of the door. When liftedthe lower lever throws the dead bolt, locksthe door and turns the indicator the showthat the room is occupied. When this leveris depressed the dead bolt and the latchbolt are withdrawn and the indicatorshows that the room is vacant.

Door preparation1. Prepare lock mortice, ensuring that the

outer lock forend is flush with theedge of the door.

2. Fold the lock template on the line ofthe outer lock forend and place it onthe edge of the door.

3. OUTSIDE FACE (TOP FOLLOWER)Position the template on the door andmark the centre of the top followersquare (top square on outside). Drillthrough Ø25mm into the mortice and6mm into the opposite side.

4. INSIDE FACE (BOTTOM FOLLOWER)Position the template on the door andmark the bottom follower (inside), drillthrough Ø25mm into the mortice and6mm into the opposite side.

5. Before inserting the lock into themortice check the hand of thelatchbolt and if necessary change thehand. Insert the lever fixing plates intothe lock so that the flat plate is theopposite side of the lock to the lever.Insert the lock into the morticecomplete with the lock fixing plates &secure with the screws provided.

6. Push lock into mortice and secure itwith the wood screws provided.

7. Fix the 9052NT spindle into the topfollower and slip the black plastic drilljig over the spindle so that it is pushedagainst the outside face of the door.With the two holes of the jighorizontal and the third at the bottom,drill all three holes Ø8mm through tothe lock case.

8. Push the lever over the spindle and fixthe inner rose to the lever fixing platethat is held between the lock and thelock mortice.

9. Check the function and tighten thespindle fixing screw, check functionagain.

10. From the outside face of the door pushthe 9055 spindle (5mm square hole upcentre) through the lock, push thelever & rose assembly onto the spindleand with the M3.5 x 25mm screws fixinto the lever fixing plate.

11. Check that the lever operates thelatch bolt when pressed down andthat the deadbolt is thrown when thelever is lifted. Tighten the spindle grubscrew and check the function again. Ifthe lock does not function correctlythen the fixing screws could havebeen overtightened.

12. Finally fix the ‘Lift lever to lock’ roseand the indicating rose

Inside face Outside face

LiftLeverto Lock



7279Vertical Euro profile cylinder mortice lock.

72

38

11

b

a

165

20

21.5

4631

35

42 24

24

25 22

145 235 233206 209235

16

13.5

11

9 9

20

Case sizes

Ref. No. Handle Forend a b7279.60 Lever Square 92 607279.80 Lever Square 112 807279K10 Knob Square 132 1007279F60 Lever Radius 92 607279F80 Lever Radius 112 807279KF10 Knob Radius 132 100

• Three modular case sizes – see tablebelow

• Cylinder can withdraw both latch anddeadbolt in one action – offers conven-ience and safety combined with security

• Deadbolt– high security 20mm single throw

• Latchbolt– reversible without removing the

lockcase cover




• All 3 case sizes have 72mm centres





• Bolt through fixing holes for levers andcylinder

• When escutcheons are being used, on adouble cylinder, extra rigidity can be obtainedby using the XX9501 distance piece forback-to-back fixing through the lockcase –this is essential on metal doors

3 X 8 1 0 F 1 K A 3 0






7282Vertical Euro profile cylinder morticeapartment lock.

72

38

11

60

92

165

20

21.5

4631

35

42 24

24

25 22

145 235 233206 209235

16

13.5

11

9 9

20

Lever handles on both sides will withdrawlatch bolt, except if deadbolt is projectedwhen inside handle only will withdraw bothbolts. Door then remains unlocked untilmanually re-locked by key from outside orturn from inside. Satisfies Building Regulationrequirements for multi-occupancy buildings.

• Single case size as illustrated


lockcase cover


• Follower – 2 part to enable security and safety

functions to operate


• Forend and strike plate– square 7282.60– radiused 7282F60– range of metallic finishes– forends available in Spectra colours– pre-formed strike plate– reversible strike plate


• Bolt through fixing holes for levers andcylinder

• When escutcheons are being used, on adouble cylinder, extra rigidity can be obtainedby using the XX9501 distance piece forback-to-back fixing through the lockcase –this is essential on metal doors





7286Vertical Euro profile mortice deadlock.

30

38

b

a

165

20

24 22

235 233209

35

16

11

125136 125

25

25 17

11.5

62

40

62

Case sizesRef. No. Forend a b7286.60 Square 92 607286.80 Square 112 807286.10 Square 132 1007286F60 Radius 92 607286F80 Radius 112 807286F10 Radius 132 100

• Three modular case sizes – see tablebelow




• Forend and strike plate– option of square or radius– range of metallic finishes– forends available in Spectra colours– supplied with pre-formed box strike– for common frame preparation, a

lipped strike is available as 7279


• Bolt through fixing holes for cylinderescutcheon

• When escutcheons are being used, on adouble cylinder, extra rigidity can beobtained by using the XX9501 distancepiece for back-to-back fixing through thelockcase – this is essential on metaldoors



3 X 8 1 0 F 1 K A 0 0


Severe duty locks and latches

HD99’ RedlocksWith fire, safety and security in mind,Allgood has designed the HD99‘ Redlocks.The range is particularly suitable for severeusage doors and where a higher degree ofsecurity is required. Redlocks are availablewith a special bolt to allow use withapproved 19mm electric release or monitorstrikes and can be manufactured toincorporate microswitch monitors for alarmand access control (add the suffix “E” tothe lock reference number).

• Common case size for all functions –makes locks interchangeable, and doorscan be upgraded with the minimum ofjoinery alteration.

• Oval cylinder locks are supplied asstandard. Euro profile cylinder versionsare also available from stock – add suffix“P” to lock number.

• Inner forends are rounded – to assistwith factory morticing.

• The back of the inner forend is flat – toease door preparation on steel doors.

• Specially designed to suit standard ANSIpreparation – making Redlocks suitablefor steel doors.

• The 9990HD Redlock has an ‘always freeto escape’ facility – thus meeting theconflicting requirements of fireregulations and the need for security.

• Latchbolts are reversible withoutremoving the lockcase cover – non-handed locks simplify specification andsave time on site.

• Supplied with a pre-formed strike – forease of installation.

• Latchbolts are guided and comprise a 3part easy action stainless steelconstruction with a 19mm throw (except9964 – 25mm – see overleaf) – veryhigh durability and security. Additionalsecurity is gained from the hardenedanti-saw trigger.

• Lockcases have bolt through fixing holes.• Strikeplates are hardened 3I6 stainless

steel to resist surface scratches.• UL listed and comply with ANSI 115.1

and PSA performance requirements.• Fixing screws are provided (Type AB self-

tapping) – suitable for both timber andmetal.

• Rebate conversion sets for allRedlocks are available for 13, 19 and25mm rebate depths on double doors– to allow locks to be fitted in mostrebated door sections. Redlocks arenot suitable for rebated doors lessthan 50mm thick.

• The locking function on the 9962HDand 9990HD locks can be changedwithout removing the cover. Thesebolts have 2 part followers to allowthe security and safety functions tooperate, and require furniture withspecial security spindles; Modric andMode door furniture should bespecified with the suffix “/9N”.

• All locks except 9960 and 9964incorporate an anti-thrust bolt – toprevent bolt being pushed back.

• The 9971HB and 9981HB have alatch holdback. The latchbolt isdepressed and the holdback activatedby the key 789A, through the forend.Reversing the procedure releases thebolt.

• The deadlocking night latches 9980 and9981HB are especially suitable toprovide extra security for glass panelleddoors, as the bolt and the handles aredeadlocked at the same time and canonly be released by the key.

• The 9964 Redlock has a 25mmprojecting deadbolt which incorporateshardened steel anti-saw rollers. Thematching strike plate is reinforced.


HD 99’ Redlocks

9960Vertical mortice latch.

9960-000 Levers/knobs both sides to withdraw latchbolt.9960-002 Lever/knob inside only to withdraw latchbolt.

-000 -002

36

134

37

56

203

19

72

108

35–38

124

184 203

44 5186105

32

32

28.5

26 10

16

17

17

21

• Case size – 134x108x20mm

• Backset – 72mm


lockcase cover– guided and comprises a 3 part low

friction anti-saw trigger stainless steel construction with a 19mm throw

• Inner forend– rounded– flat backed for flush fitting in metal

doors

• Suits standard ANSI preparation formetal doors

• Supplied with preformed strike

• Bolt through fixing holes


• UL listed and complies with ANSI 115.1and PSA performance requirements


• Heavily sprung for lever handles – addthe suffix “K” when using knobs

• Rebate conversion set 9952 available forthis latch – specify 13mm, 19mm or25mm (Note: Redlocks are not suitablefor rebated doors less than 50mm thick)



HD 99’ Redlocks

9962HDVertical oval cylinder mortice apartmententrance lock. Euro profile version available(add suffix “P” to lock number).

9962HD-060 Levers/knobs both sides with ‘/9N’ spindle to operate latchbolt except when external handle isrendered inoperative by cylinder either side. Depressing inside handle withdraws latchbolt andreleases external handle.

9962HD-140 Levers/knobs from both sides with ‘/9N’ spindle to operate latchbolt except when external handle isrendered inoperative by cylinder or inside turn. Depressing inside handle withdraws latchbolt andreleases external handle.

-060 -140

36

72

16

134

37

10203

19

10

72

108

35–38

124

184 203

44 5186105

32

32

28.5

26 10

16

12

17

17

21

• Case size: 134x108x20mm

• Backset and centres – 72mm

• Anti-thrust bolt

• Latchbolt:– reversible without removing lockcase

cover – guided and comprises a 3 part low

friction anti-saw trigger stainless steel construction with a 19mm throw

• Locking function: changeable withoutremoving lockcase cover

• Follower 9.5mm:– 2 part to enable security and safety

functions to operate

– requires furniture with special security spindles: Door furniture should be specified with the suffix “/9N”

• Inner forend:– rounded– flat backed for flush fitting in metal

doors



• Bolt through fixing holes for levers



• When using Modric, Mode leverbackplates, add the suffix “HD” to theplate number

• Heavily sprung for lever handles – add the suffix “K” when using knobs,

and remove the “HD” suffix

• Rebate conversion set 9952 available forthis lock – specify 13mm, 19mm or25mm. (Note: Redlocks are not suitablefor rebated doors less than 50mm thick)



HD 99’ Redlocks

9964 Vertical oval cylinder mortice deadlock witha 25mm throw. Euro profile versionavailable (add suffix “P” to lock number).

9964-060 Cylinder operation from both sides.9964-080 Cylinder operation from one side only.9964-140 Cylinder operation from one side and turn from the other.

-060 -080 -140

108

16

134

38

61

203

25

72

108

124

184 203

66105

6438

32

32

28.5

26

12.5

17

14


• Backset – 72mm

• Deadbolt– 25mm in a single throw– incorporating hardened steel pins– reinforced matching strike plate


doors


• Supplied with flat strike






HD 99’ Redlocks

9970 Vertical oval cylinder mortice non-deadlocking night latch. Euro profileversion available (add suffix “P” to locknumber).

9970-060 Cylinder operation from both sides to withdraw latchbolt.9970-080 Cylinder operation from outside and lever/knob from inside to withdraw latchbolt.9970-140 Cylinder operation from outside and turn from inside to withdraw latchbolt.

-060 -080 -140

36

72

16

134

37

10203

19

10

72

108

35–38

124

184 203

44 5186105

32

32

28.5

26 10

16

12

17

17

21






friction stainless steel construction with a 19mm throw


doors










HD 99’ Redlocks

9971HBVertical oval cylinder mortice non-deadlocking night latch with holdbackfacility. Euro profile version available (add suffix “P” to lock number).

9971HB-060 Cylinder operation both sides to withdraw latchbolt.9971HB-080 Cylinder operation from outside and lever from inside to withdraw latchbolt.9971HB-140 Cylinder operation from one side and turn on the other to withdraw latchbolt

-060 -080 -140

36

72

16

134

37

10203

19

10

72

108

35–38

124

184 203

44 5186105

32

32

28.5

26 10

16

12

17

17

21




• Latch holdback– latchbolt is depressed and hold back is

activated by the key 789A, through the forend

– reversing the procedure releases the bolt





doors









9980Vertical oval cylinder mortice deadlockingnight latch. Euro profile version available(add suffix “P” to lock number).

36

72

16

134

37

10203

19

10

72

108

35–38

124

184 203

44 5186105

32

32

28.5

26 10

16

12

17

17

21

9980-060 Lever/knob from inside withdraws latchbolt except when deadlocked. Cylinder operation from bothsides to withdraw or deadlock latchbolt.

9980-061 Levers/knobs from both sides withdraw latchbolt except when deadlocked. Cylinder operation fromboth sides to withdraw or deadlock latchbolt.

9980-080 Lever/knob from inside withdraws latchbolt except when deadlocked. Cylinder operation from outsideto withdraw or deadlock latchbolt.

9980-081 Levers/knobs from both sides withdraw latchbolt except when deadlocked. Cylinder operation fromoutside to withdraw or deadlock latchbolt.

9980-140 Lever/knob from inside withdraws latchbolt except when deadlocked. Cylinder operation from outsideand turn inside both withdraw or deadlock latchbolt.

9980-141 Levers/knobs from both sides withdraw latchbolt except when deadlocked. Cylinder operation fromoutside and turn inside both withdraw or deadlock latchbolt.

9980-170 Lever/knob from inside withdraws latchbolt except when deadlocked. Turn operation from inside towithdraw or deadlock latchbolt.

9980-171 Levers/knobs from both sides withdraw latchbolt except when deadlocked. Turn operation from insideto withdraw or deadlock latchbolt.

-060 -061 -080 -081

-140 -141 -170 -171








doors


• Especially suitable to provide extrasecurity for glass panelled doors; handlesare deadlocked at the same time andcan only be released by the key









HD 99’ Redlocks


HD 99’ Redlocks

9981HBVertical oval cylinder mortice deadlockingnight latch with holdback facility. Europrofile version available (add suffix “P” tolock number).

9981HB-060 Cylinder operation from both sides to withdraw or deadlock latchbolt.9981HB-080 Cylinder operation from one side only to withdraw or deadlock latchbolt.9981HB-140 Cylinder operation from one side and turn on the other to withdraw or deadlock latchbolt.

-060 -080 -140

36

72

16

134

37

10203

19

10

72

108

35–38

124

184 203

44 5186105

32

32

28.5

26 10

16

12

17

17

21




• Latch hold back– latchbolt is depressed and hold back is

activated by key 789A, through the forend

– reversing the procedure releases the bolt





doors


• Especially suitable to provide extrasecurity for glass panelled doors; handlesare deadlocked at the same time andcan only be released by the key








9990HDVertical oval cylinder mortice escape nightlatch. Euro profile version available (addsuffix “P” to lock number).

9990-060 Levers/knobs from both sides with ‘/9N’ spindle to operate latchbolt, except when external handlerendered inoperative by cylinder either side.

9990-080 Levers/knobs from both sides with ‘/9N’ spindle to operate latchbolt, except when external handlerendered inoperative by cylinder outside.

9990-140 Levers/knobs from both sides with ‘/9N’ spindle to operate latchbolt, except when external handlerendered inoperative by cylinder outside or turn inside.

-060 -080 -140

36

72

16

134

37

10203

19

10

72

108

35–38

124

184 203

44 5186105

32

32

28.5

26 10

16

12

17

17

21



• ‘Always free to escape’ facility – solvesconflict between fire regulations andsecurity requirements, as per “Secure byDesign” proposals


• Latchbolt– reversible without removing lockcase

cover– guided and comprises a 3 part low


• Locking function – changeable withoutremoving lockcase cover

• Follower 9.5mm:– 2 part to enable security and safety

functions to operate– requires furniture with special security

spindles: Door furniture should be specified with the suffix “/9N”


doors






• Heavily sprung for lever handles – addthe suffix “K” when using knobs, andremove the “HD” suffix



HD 99’ Redlocks


7518Cubicle mortice deadlock.

2

5022

76

58

388

10

89

8

3371

18 18

13

10

89 8971 50 26

• Deadbolt operated by indicator/releasefrom outside and by snib from inside

• 8mm follower


• Satin nickel plated bolt


75’ locks


75’ locks

7519Claw bolt cubicle sliding door morticedeadlock.

2

6

24

26

13

36.5

48

75.5

57

11

89

8

8

28.5

33

28.5

71

25 25

13

10

90 71 4889

32

6.5

66

6.5

32

• 8mm follower


• Claw bolt operated by indicator/releasefrom outside and by snib from inside



83’ locks

8397Katkin access panel lock.

MA8397AKatkin key with hole for chain.Plated steel finish.

3

16

2X

76

16 14

1719

35

76

Not approved forfire as insufficientdoor thickness

FD 30

FD 60

• Suitable for duct doors, removableskirtings, access panels, cupboards etc.

• Flush fitting

• Suitable for left or right hand hingeddoors or removable panels

• Thief resistant

• Special captive key can only be removedin the locked position

• Key can be used as a handle to lift outaccess panels

• Has been included in satisfactory firetests to BS EN 1634 (30/60 mins) – seetable below

Finishes: PB • SC • PCSee below for ordering product accordingto length of panel lock and finish (in thisexample the finish is satin chrome – SC)

ALSO AVAILABLEXX8397R Katkin rubbing plateZinc plated steel finish

XX8397S Katkin slot plateZinc plated steel finish

XX8397U Katkin angle plateZinc plated steel finish

“X” door thickness Product number13 SC8397/1319 SC8397/1925 SC8397/2535 SC8397/3538 SC8397/3845 SC8397/4550 SC8397/5054 SC8397/5463 SC8397/63

}}}


Fixing instructions

Fixing Instructions for Rebate ComponentsBefore fixing:

a) Check that the hand of the lock is

correct. If not, reverse the bolt as shown

on the lock fixing template supplied

with the lock.

b) The rebate set is reversible. With

Redlocks it is only suitable for doors

50mm minimum thickness. The size of

the rebate is defined by the distance (z)

on the drawing. The components are

available for 13mm, 19mm or 25mm

rebate.

c) The lock must be fitted into the opening

door leaf and the strike plate into the

fixed leaf.

1. Mortice the lock into the centre of the

door edge at the required height.

2. Insert the lock and mark around the

forend plate (b) on the projecting edge

of the door. Cut out to the required

depth to suit the rebate strip (a).

3. If required, holes for furniture or

cylinders should now be made in the

door faces as required. See lock fixing

template.

4. Hold the rebate strip (a) behind the lock

forend plate (b) and fix the lock into the

prepared door using the screws

provided. Fix the lock face plate (c).

5. With the lock firmly secured, mark the

position of the bolts on the other door

and cut out holes to the required depth.

Important: Before cutting the holes,

check whether both holes are required

(for locks) or latchbolt hole only (for

latches or night latches) or deadbolt

hole only (for deadlocks and some

escape deadlocks).

6. Position the strike plate and cut into the

edge of the door until it is morticed

flush with the back edge of the rebate.

7. Cut out a notch for the tongue of the

strike plate (d).

8. The lip on the long outer edge of the

rebate strip (d) must be morticed into the

projecting edge of the door for a neat

finish.

9. Hold the strike plate in position and fix

into the door edge, through the strike

plate, using the screws provided.

z

x y

Lock sideOpening door leaf

Strike plate sideFixed door leaf

Assembled view

a

b

c

Lock in opening leaf (x)

d

Striking plate in fixed leaf (y)(viewed from open edge for clarity)

Assembled view


Mechanical cylinder master keying

A full master keying service is available forAllgood Hardware cylinders. These can beproduced under sub and grand master keysystems to customers’ details, which in turncan incorporate construction master keying.

Allgood Hardware Euro profile, oval, roundthreaded and rim cylinders and cylinderpadlocks can be suited together. However,it should be noted that the AdvancedCylinder Series and the Advanced HighSecurity Cylinder Series use different keysections, so they cannot be suited togetherunder the same master keying system.

Allgood also offers the convenience of aconstruction master key system. Keys areprovided for the construction phase whichare then rendered void on completion of theproject, by simple insertion of the new key.From this moment on, the full master keysystem comes into effect. So site personnel,for example, can be given a key which willmeet their needs but which will cease to beof use once client/building owner uses hiskey. The only alternatives are either to riskleaving a key in the wrong hands or tochange over cylinders when construction iscomplete – clearly a costly and arduoustask. With Allgood’s construction master keysystem, security is maximised whilst labourand materials costs are kept to a minimum.

Master key suites can be delivered with acomputer generated keyplan. Key and doornumbers are recorded.

Master key systems are tailored to yourrequirements. Opposite some examples areillustrated of the various master keyingarrangements available. Please contactyour nearest Allgood office for assistance.

Figure 1 Figure 2

Figure 3

Master Key

Different Servant Keys

Common Lockopened by more than one Key

Grand Master Key

DifferentMaster Keys


Grand Master Key

Different Master Keys

DifferentSubmaster Keys


Figure 1 shows the simplest form – a plainmaster keyed system. In this system asingle key – the master key – will operateall locks in the system while each lock hasits own individual key – the servant key. Itis sometimes required that several servantkeys should be able to operate onecommon lock (e.g. the lock for the entrancedoor of a block of flats). This arrangementis shown in dotted lines on the illustration.

Provided the number of different keyswhich are to operate the common lock arefew in number, the arrangement issatisfactory and convenient. With a largenumber of different keys the security of thecommon lock is reduced almost toextinction. Under these circumstances it ispreferable to fit, for the common lock, onewhich is outside the master keyed systemaltogether.

Figures 2 & 3 show more elaborate masterkeyed systems wherein there are two ormore different levels of master key.

In Figure 3 the dotted lines show that agroup of locks, each with their own servantkey, can be made to accept the grandmaster key only and exclude any masterkey of lower levels.

A suite expansion of approximately 20% isbuilt into all plans. More can be catered for,only if requested when ordering.


Advanced cylinder series

7418AEuro profile double cylinder with keyoperation on both sides.

Variations (mm)V W

a 65 32.5 (standard)b 73 36.5c 85 42.5

Finishes: MA • SC • PC • TA • PB • PZSatin nickel – XX7418NA (full ref.)

33

17

10

WV

Variations (mm)V W

a 65 32.5 (standard)b 73 36.5c 85 42.5


33

1726

17 25WV

10

7419AEuro profile cylinder with key operation onone side and unique Allgood turn on theother.

7420A Euro profile single cylinder with keyoperation on one side only.

Variations (mm)V W

a 42.5 32.5 (standard)b 46.5 36.5c 52.5 42.5


33

17 WV

10

• 65 or 42.5mm length cylinder suppliedas standard. If door thickness is greaterthan 49mm, please state on your order

• Available in three lengths, to suit a widerange of door thicknesses. A wider rangeof cylinder lengths is available to specialorder

• If lock is installed off-centre, pleasecontact your nearest Allgood office forassistance

• Tested to BS EN 1303, Grade 6 durability,Grade 2 security

• Double paracentric keyway overlappingin three positions; resists picking

• Mushroom type drivers; make aligning ofthe pins by a picking tool almostimpossible

• Off-centre cam protrudes from thecylinder body when the key is removed;prevents cylinder being driven throughthe lockcase by severe force such as by ahammer

• 5 pins with a hardened steel pin anddriver in the first position; resist drillingthrough pins

• Hardened steel anti-drill pin at each endresist drilling through body

• Exclusive “TG” Triple Grooved anti-pickpins provide even greater resistence topicking

• Supplied with 2 keys as standard (unlessspecified). Additional keys providedwithin 24 hours (excluding Mastersuiting), are available from Allgood;greater assurance of security

• Available individually keyed or as part ofa master key suite to customerrequirements

• Allgood can also provide a constructionmaster key system affording convenienceduring the construction phase and theassurance of total security on buildingcompletion, without the need to changeover cylinders (see Master Keyingsection)

Advanced mechanical cylinder seriesFeatures and their benefits

• It is essentail that only special aerosollubricant XX9568 be used in and aroundthe cylinder/cylinder & turn, and the key.Do not use oil, grease or otherlubricants.

Finishes: MA • TA


• Tested to BS EN 1303, Grade 6 durability,Grade 2 security

• Double paracentric keyway overlappingin three positions; resists picking

• Mushroom type drivers; make aligning ofthe pins by a picking tool almostimpossible

• 5 pins with a hardened steel pin anddriver in the first position; resist drillingthrough pins

• Hardened steel anti-drill pin at each endof the body; resist drilling through body

• Exclusive “TG” Triple Grooved anti-pickpins; provide even greater resistance topicking

• Supplied with 2 keys as standard (exceptcylinders to pass, where one key issupplied)

• Replacement keys are available fromAllgood

7401ARound cylinder for 8369 and 8370 rimnight latches and 9315 Touchbar panichardware.

32

5

29

25

21

32

110

Advanced cylinder series

7402ARound threaded cylinder to suit 9316Aexternal access device and Adams Ritelocks.

32

2532

29

7402TRound threaded cylinder turn to suit AdamsRite locks.

32

2532

29

Finishes: MA • TA • PZFinishes: SC • PC • TA • PB • PZ Finishes: SC • PC • TA • PB • PZ

Round threaded advancedcylindersFeatures and their benefits

• Available individually keyed or as part ofa master key suite to customerrequirements

• Allgood can also provide a constructionmaster key system affording convenienceduring the construction phase and theassurance of total security on buildingcompletion, without the need to changeover cylinders (see Master Keyingsection)

• It is essential that only special aerosollubricant XX9568 be used in and aroundthe cylinder, and the key. Do not use oil,grease or other lubricants.


Cylinder and turn only

7447APREuro profile cylinder with unique Allgoodturn only.

1726

25 WV

33

17

10

Variations (mm)V W

a 42.5 32.5 (standard)b 46.5 36.5c 52.5 42.5

Finishes: MA • SC • PC • TA • PB • PZ

7447AOval cylinder with unique Allgood turnonly.

Variations (mm)V W

a 42.5 32.5 (standard)b 46.5 36.5c 52.5 42.5

Finishes: MA • SC • PC • TA • PB • PZ

32

1726

17.5 25 WV

• 42.5mm length cylinder supplied asstandard. If door thickness is greaterthan 49mm, please state on your order.

• If lock is installed off-centre, pleasecontact your nearest Allgood office forassistance.

• A wider range of cylinder lengths isavailable to special order.

• Available in three lengths, to suit a widerange of door thicknesses.

• It is essential that only special aerosollubricant XX9568 be used in and aroundthe cylinder, and the cylinder and turn.Do not use oil, grease or otherlubricants.

Cylinder and turn onlyFeatures and their benefits


Contents


• Roller catch

• Magnetic catch

• Construction levers

• Special spindles

• Distance piece

• Screwdrivers

• Budget mortice lock

• Door silencers

• Configurations fixing list



Micellaneous hardware


Miscellaneous hardware

XX9030Construction levers (8mm spindle), pair.

Combined levers and 8mm spindles foruse with standard locks duringconstruction phase to prevent damageto finished ironmongery.

XX9030NConstruction levers (9.5mm spindle),pair.

Combined levers and 9.5mm spindlesfor use during construction phase toprevent damage to finishedironmongery.

XX9032Construction lever (8mm spindle).

Single sided fix combined lever and8mm spindle for use during constructionphase to prevent damage to finishedironmongery.

63 53 70 60

17 14

64 51 76 65

442222

XX10772Adjustable heavy duty roller catch.

Brass finish.For satin chrome finish, specify XX10772SC.

XX10780Magnetic catch.

• 6kg holding force

• White moulded finish



9.5mm heavy duty HT singletite spindle for38–57mm thick doors, to be used with9962HD and 9990HD HD99’ Redlocks.

XX9069NSingletite spindle.

8mm heavy duty HT singletite spindlefor 38–57mm thick doors, to be usedwith 7282, 9962K and 9990K HD99’Redlocks.

XX9069TSingletite spindle.

XX9070NAs above, but for 58–76mm thick doors.

XX9070TAs above, but for 58–76mm thick doors.

XX9064TSupplied as standard with through bolts forAllgood quadaxial handles.For doors 35–55mm thick.

XX9066TFor 44–64mm thick doors.


XX9068T

For 91–114mm thick doors. Pleasenote this door thickness optioncomes with face fix screws, ratherthan through bolts.


The options below are for other doorthicknesses.



XX9501Back-to-back fixing.

Indicator drive spindle to allow use of 5mmindicators with 8mm followers.

XX9055Indicator drive spindle.

8mm HT Taylor spindle for single-sided rigidfixing knob.

XX9050TTaylor spindle.

Mortice rigidiser for rigid fixing of mostdoor furniture. Suits 8mm spindles and38mm centre fixing roses.

182

5585

18

6 8 6

XX47460Rigidiser.

8mm HT half spindle to be used withlever/knob half sets. Requires hole drilledthrough door.

XX9051THalf spindle.

8mm HT half spindle for 35–54mm thickdoors, to be used with half sets of Modricor Mode lever or knob furniture withAllgood locks or latches. Requires singleside drilling only.

XX9052NTHalf spindle.



XX5321Pozidriv/Supadriv screwdriver, for 4–6g self-tapping screws.

XX5322Pozidriv/Supadriv screwdriver, for 6–10gwood screws.

XX5323Pozidriv/Supadriv screwdriver, for 12–16gscrews.

Note: Allgood Hardware Pozidriv/Supadrivscrews should be driven home so that theslots on the heads are horizontally andvertically aligned. The correct AllgoodHardware screwdriver must be used.Particular care should be taken when fixingSpectra colour coated screws; each fixingshould first be ‘piloted’ with an equivalentscrew which can then be replaced with theSpectra coated one.

XX5321 / XX5322 / XX5323

19

1018

XX11010WGrey rubber door silencer for woodframes.

13

14 13

XX11010SGrey rubber door sliencer for steelframes.

Requires XX10793 ‘T’ keyFinish: Bright zinc plate

XX10795Steel budget mortice lock with slottedstrike plate.

XX9568Special aerosol lubricant for allcylinders.



2

100

10

8 25 25

100

8

117

7

75

2

810

25 25 25

90

25

50

19

25mmø piloted cutter

22mmø Forstner bit

8mm drill bit

XX9562Ball-ended T-bar hex driver. Use instead ofthe ball-ended hex wrench (supplied withall lever handles).

XX9561Quadaxial tool kit comprising 22mmøForstner bit, 25mmø piloted cutter, 8mmødrill bit, XX9562 ball-ended T-bar hex driverand ball-ended ‘whizzer’. To suit Quadaxiallever handle assemblies.

XX9560Recycled plastic drill alignment jig.Supplied as standard with all pairs of leverhandles. Once spindle hole has been drilledaccording to the lock template, it fits overthe spindle to allow accurate drilling ofbolt-through holes.

XX9563Pack of 5 ball-ended ‘whizzers’ to suitpower drivers or low torque electric drills.Maximum recommended torque is 1.5Nm(use the lowest setting available). Useinstead of the ball-ended hex wrench(supplied with all lever handles) or the ball-ended T-bar hex driver.

2

100

Ball-ended T-bar hex driverAlso available separately (see right).

Ball-ended ‘whizzer’Packs of 5 also available separately (see right).

Fixing toolsThe tools listed on this page ensure thatfixing Quadaxial lever handle assemblies isfast, simple and accurate.

Comprehensive fixing instructions, theunique Allgood drill alignment jig and aball-ended hex wrench are included withevery assembly, so it is possible to fixSembla, Mode and Modric lever handleswith your own cutting and drilling tools.

However, we strongly recommend that youdo specify the Allgood tools – they areextremely competitively priced and themore lever handles are to be installed, themore time will be saved. Furthermore, youwill be assured of accurate fixings andlong-lasting, reliable performance toreinforce Allgood’s 10-year warrantyagainst mechanical defect on all products.

The XX9561 tool kit comprises all thecutting and drilling tools needed to fix yourlever handles. It also includes an XX9562ball-ended T-bar driver that provides forfaster and easier tightening of the bolt-through fixings – a very useful alternativeto the ball-ended hex wrench supplied withevery lever handle assembly.

If you already have the necessary cuttingand drilling tools, the XX9562 ball-ended T-bar driver is also available as a separateitem.

For the ultimate in speed and convenience,specify the XX9563 pack of 5 ball-endedwhizzers. These do the same job as theT-bar and the hex wrench but are designedto be used with a power driver orlow-torque electric drill.

7

75

2


Contents

• Foreword

• Mechanical digital locks

ForewordMechanical digital locks are the simplestform of access control. Without the needfor mains power, or any external wiring oradditional equipment, they provide a stepup in security and convenience frommechanical keyed locks. They are perfectwhere a simple ‘all-in-one’ solution isrequired.

Keyed locks can provide different accesslevels through master keying. Some digitallocks can be ‘master keyed’ and they alsoprovide many other features (depending onthe lock) which allow for a moresophisticated control of access and egress.You can have a special one-time emergencyor service entry code, for instance, whicherases the memory once used. Lock releasetimes are adjustable. Management cantemporarily or permanently disable any orall user codes. Locks can provide visibleand audible entry indicators, and beoverridden from a remote point.

Above all, mechanical (and the batterypowered 72102N) digital locks canconveniently solve the problems that comewith key based locking systems. There isalways the issue of lost or unreturned keysor there may simply be an unwieldynumber of keys, or perhaps there is now achange of priority for a given door. Withcode entry instead of keys, problems aresolved. Easily changed, as often as you like,codes provide a flexible means of accesscontrol. You will see on the following pagesthat all the options of sophisticated morticelocks are also available, examples beingalways-free-to-escape, key override, andlatch holdback facilities.

Please bear in mind that these locks aredesigned for low-to-medium frequency use.Where there is higher traffic, you shouldconsider some form of electronic accesscontrol. In this case The functionalequivalent to mechanical digital locks, isthe range of electronic code keypads(Section 6.1).

Mechanical digital locks



71202NStand-alone, digital lock.

• Designed for medium frequency use.

• Suitable for internal and externalmounting.

• Powered by on-board batteries, providing120,000 operations.

• Full size lever (or knob – see right)operation from both sides allows single-handed use for access and egress.

• Inside handle provides free escape at alltimes.

• Clutch mechanism only engages outsidelever when correct code entered,preventing forced entry and damage tolock.

• Key override and passage set functionsallow access without needing to usecode.

• Anti-thrust deadlocking latchbolt providessmooth, secure locking action.

• Up to 15 user codes with managementand master codes provide hierarchicallevels.

• One-off service code option allows visitoror contractor to use code which willimmediately be cancelled after its firstoperation.

• Adjustable lock release time.

• Remote release option available.

• Low power audible alert.

• Automatic penalty time after threeincorrect entries.

• Easy to install – retrofits to doorspreviously fitted with Unican locks.

• Suitable for doors 41–48mm thick.

• Version 71205 is also available for doors48–54mm thick.

Finish: SC

83 8347 43

65 65121

188 210

1270

(backset)

71123Conversion component for 13mm, 19mm or25mm rebates.

7112595mm backset extension.


71204NKnob version of 72102N.

83

83

47 43

75 75

188

210

1270

(backset)

• Suitable for internal mounting only.



71101Digital mortice night latch.

71102As 71101, but with key override.

• Designed for medium-frequency use.

• Deadlocking anti-thrust latchbolt,providing smooth, secure locking action.

• Full size knob operation from both sidesallows single-handed use for access andegress.

• Inside knob provides free escape at alltimes.

• ‘Slipping clutch’ mechanism preventsillegal entry and damage to lock.

• Codes easily changed without removinglock from door.

• Access to this panel is by locked coverplate so only authorised personnel canundertake combination changeprocedure.

• Non-handed.

• Adjustable for door thicknesses of 35-54mm.

Finish: SC.

The variations on the right allow forcombinations of passage set – wherebyboth knobs will retract the latchboltwithout the use of a code – and keyoverride facilities.

79

95 8360

60

1970

(backset)

188 228

71123Conversion component for 13mm, 19mm or25mm rebates.



71103With passage set (set by thumbturn).

71104With both passage set (set by thumbturn)and key override.

71105With passage set (set by keyed cylinder).

71106With both passage set (set by keyedcylinder) and key override.



71080Digital night latch.

• Designed for low- to medium-frequencyuse.

• Deadlocking anti-thrust latchbolt.

• Inside turn allows free escape at alltimes.

• The base of outside of unit operates asintegral pull.

• ‘Slipping clutch’ mechanism allowsoutside turn to slip through 90º if forced,preventing illegal entry and damage tolock.

• Codes easily changed without removinglock from door.

• Key override facility is not available.

• Compatible with Allgood rimnightlatches.

• Suitable for doors 44mm.

• Other finishes available on request.

Finish: SC

57 12

51

57

6070

156

57

51


Electric strikes for timber frames

75019NCElectric strike for timber frames with lockswith 13mm bolt projection.

31.82.4

25.1

43

201.685.6 85.6

41.616.5

For locks with 19mm bolt projection.

31.82.4

25.1

45.4

201.685.6 85.6

46.421.3

Specification table 13mm bolt 19mm bolt

12v DC Fail Secure Non Monitored 75019NC 75055NCSingle Monitored 75025NC 75061NCTwin Monitored 75027NC 75063NC

12v DC Fail Safe Non Monitored 75021NC 75057NCSingle Monitored 75029NC 75065NCTwin Monitored 75033NC 75069NC



Electric strikes are fitted in place ofstandard striking plates to allow electricallycontrolled access and egress without theneed to operate the mechanical lock fittedto the door.

Specification

Select your strike according to thefollowing criteria.

• Door type – timber or metal

• Lock bolt projection – 13mm or 19mm

• Voltage – 12v DC or 24v DC

• Fail secure (fail locked) or fail safe (failunlocked)

• Monitoring– single monitoring indicates that thelock bolt is within the cam of the electricstrike

– twin monitoring also indicates theposition of the solenoid and whether thecam is locked or unlocked.


Electric strikes for metal frames

75001NCElectric strike for metal frames with lockswith 13mm bolt projection.

Specification table 13mm bolt 19mm bolt





31.82.4

25.1

43

123.785.6 85.6

41.616.5

For locks with 19mm bolt projection.

31.82.4

25.1

45.4

123.785.6 85.6

46.421.3

Electric strikes are fitted in place ofstandard striking plates to allow electricallycontrolled access and egress without theneed to operate the mechanical lock fittedto the door.

Specification

Select your strike according to thefollowing criteria.• Door type – timber or metal

• Lock bolt projection – 13mm or 19mm

• Voltage – 12v DC or 24v DC

• Fail secure (fail locked) or fail safe (failunlocked)

• Monitoring – single monitoring indicates that thelock bolt is within the cam of the electricstrike

– twin monitoring also indicates theposition of the solenoid and whether thecam is locked or unlocked.


Gravity shearlocks

With Allgood Secure 75000 range ofshearlocks, both armature and magnet aresprung, allowing gaps of up to 6mmbetween door and frame to be overcome.Once engaged, they provide over 1200kgholding force, achieved without the highoperating temperatures associated withother shearlocks.

Being fully concealed within the door andframe, mortice shearlocks also providesuperior security and aesthetics. AllgoodSecure gravity shearlocks are fire tested toBS 476 Part 22 for 30 minutes. Shearlockscan be supplied for surface mounting, flushdoor and frame application, or semi-concealed for doors in recessed frames.

For shearlocks to function correctly, thearmature and magnet must align exactly.As such, Allgood Secure does notrecommend their use on double actiondoors.

Certain locks incorporate magnetic bondsensing (MBS). This is a self-monitoringdevice incorporated within the magnetwhich detects the holding force of thearmature and magnet when the door isclosed. If the full holding force has notbeen achieved it can signal a visual alarm,either locally or at a remote console, toindicate the magnet is not operating at itsmaximum holding capacity.

75403As above, but with magnetic bond sensing(MBS).

75401Mortice gravity shearlock electromagnetwith armature.

270

213

241

208

38

38

35

• 1225kg holding force.

• BS 476pt22 for 30 minutes.

• Built-in auto-relock switch withadjustable time delay and cooltemperature regulator.

• Automatic 12/24v DC voltage selection.

• Current draw: 900mA @ 12v or 450mA@ 24v.


T 0870 609 0009 www. allgood.co.uk Secure 6.2

Mini shearlocks

Allgood mini-shearlocks are ideal for fittinginto narrow frames and doors. The slimlinestyle of the shearlock is achieved by havinga separate PCB, which can be fixed eitherin the PSU or mounted separately inside aprotective box, which is supplied with theshearlock. (The PCB must be fitted within20 metres of the shearlock). Being fullyconcealed within the door and frame, theshearlock provides enhanced aestheticsand security. Allgood Secure mini-shearlocks have been tested toindependently meet BS EN 1634-1 fire testsfor 60 minutes in 54mm thick doors and for30 minutes in 44mm thick doors.

By combining magnetic field force andphysical interference between lock bodyand armature, the mini-shearlock canovercome gaps of 5mm between door andframe, creating a shear holding force of1500kg.

Mini-shearlocks can also be supplied forsurface mounting or fixing to glassdoors with the use of the glass doorfixing pack (75582). For mini-shearlocksto function correctly, the armature andmagnet must align exactly. As such,Allgood Secure does not recommendtheir use on double action doors.

75580Mortice mini shearlock electromagnet witharmature.

106

116

164164

30

35

30

25

• 1500kg holding force.

• BS EN 1634-1 for 60 minutes in 54mmthick doors and 30 minutes in 44mmthick doors.

• For use in single action doorapplications.

• Dual 12/24v DC voltage.

• Current draw @ 12/24v: current surge of1.6 Amps reducing to 450mA at normaloperation.

When using with Emit systems, please addsuffix ‘E’.


Power transfer units

79052NSatin anodised aluminium armoured loop.

79053Concealed armoured loop.

323

FRAME

DOOR

25025 25

50

8066CT2(L/R)Load bearing power transfer butt hingewith Newton Bearing.

8066CT8(L/R)As above, but with 8 way powerconductors.

100

75

Clockwise closing door(Left hand hinge)

Anti-clockwise closing door(Right hand hinge)

• Surface mounted.

• Designed for carrying maximum 24v,8mm diameter cable from door frame todoor.

• Grey nylon covered spring cable.

• No connections/cable provided.

• Designed for carrying maximum 24v,6mm diameter cable from door frame todoor.

• When door is closed there are no visiblesigns of connection.

• Loop may be installed either way up,with channel in door or frame.

• Not suitable for double action doors.

• Nickel plated on steel (other finishesavailable on request).

• Do not use for 240v AC cable.

• Twin power conductors.

• Grade 316 stainless steel.

• Maintenance free and totally corrosionproof, with smoother action than ballbearings and uprated load bearing.

• 152mm free tails.

• Maximum 50v/500mA per conductor.

• For doors up to 120kg, when used inconjunction with pair of 8066CB hinges(see Allgood Hardware section).

• State hand (e.g. 8066CT2L or8066CT2R). See handing diagram below.

Finishes: TS • SS • PS


Limbar handles

675125øx228x90mm Limbar push/pull handle,with bolt through fixings.Suitable for doors 10-55mm thick. Fixingcentres at 203mm.

Finishes: MA ● TA

228

203

90

76

152

127

90

7625

6751BBAs above, pair, with back-to-back fixings.

Finishes: MA ● TA

6750BBAs above, pair, with back-to-back fixings.

Finishes: MA ● TA

675025øx152x90mm Limbar push/pull handle,with bolt through fixings.Suitable for doors 10-55mm thick. Fixingcentres at 127mm.

Finishes: MA ● TA

6752L/R25øx465x88mm Limbar push/pull handlewith bolt through fixings. STATE HAND.Left hand shown.

Finishes: MA ● TA

88 152

465

25

6752BBL/R25øx465x88mm Limbar push/pull handles,pair, with back-to-back fixings. Suitable fordoors 10-55mm thick. STATE HAND.Left hand shown

Finishes: MA ● TA


Limbar

6753L/R25øx610x80mm Limbar push/pull handlewith bolt through fixings. STATE HAND.Right hand shown.

Finishes: MA ● TA

610

610

80

25

6753BBL/RAs above, pair, with back-to-back fixingsfor doors 10-55mm thick. STATE HAND.Right hand shown

Finishes: MA ● TA


Grab handle

6560 L/R25øx457x457x79mm Grab handle with 3point fixing.STATE HAND. Left hand shown.Finishes: MA ● TA

457

79

457

25

47

3

6749N47mmøx3mm Heavy duty roses, pair, forpull handles and grab handles.

Finishes: MA ● TA ● SS ● PS


latch – free access

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop,2 kicking plates, 2 “Fire door keep shut” symbols*.

Ancillary hardware (double door, with plain meeting stile)3 pairs of hinges, 2 Fig.1 door closers*, 1 flush bolt set, 2 door stops,4 kicking plates, 4 “Fire door keep shut” symbols*.

The illustrations below are typical door sets showing the necessary hardware items for each side of the door. To assist in the selection of the correctitems, the door sets are grouped by configuration – door types. See overleaf for more details on Configurations.

lock – controlled access

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop, 2 kicking plates,2 “Fire door keep shut” symbols*.

Ancillary hardware (double door, with plain meeting stile)3 pairs of hinges, 2 Fig.1 door closers*, 1 flush bolt set, 2 door stops,4 kicking plates, 4 “Fire door keep shut” symbols*.

no lock or latch (push–pull)

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop, 1 pull handle,1 push plate, 2 kicking plates, 2 “Fire door keep shut” symbols*.

Ancillary hardware (double door, with plain meeting stile)3 pairs of hinges, 2 Fig.1 door closers*, 1 flush bolt set, 2 door stops,2 pull handles, 2 push plates, 4 kicking plates, 4 “Fire door keep shut”symbols*.

deadlock – secure

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop, 1 pull handle,1 push plate, 2 kicking plates, 2 “Fire door keep shut” symbols*.

Ancillary hardware (double door, with plain meeting stile)3 pairs of hinges, 2 Fig.1 door closers*, 1 flush bolt set, 2 door stops, 2pull handles, 2 push plates, 4 kicking plates, 4 “Fire door keep shut”symbols*.

nightlatch – apartment

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 Fig.1 door closer*, 1 door stop, 1cylinder pull, 1 letter plate, 1 inside letter plate tidy, 1 doorchain, 1 door viewer.

bathroom – privacy

Ancillary hardware (single door)11⁄2 pairs of hinges, 1 door stop, 2 kicking plates, 1 toiletdoor gender symbol.

2. Door types & hardware sets

Pram Park and Lobby

WaitingArea

Reception

ConsultingRoom

Plant Room

RecordsReception

StaffRoom

ConsultingRoom

Recovery

HealthVisitor

CommunityPracticeNurse

Children'sPlay Area

ReceptionSeating

Kitchen

Surgery

ChangingRoom

WC

This plan shows a typical doctor’s surgery with our recommended configurations/door types in bold text.Details about configuration can be found on the reverse side of the page. Once you have selected theconfiguration/door type, move to Section 2, there is an illustrated guide to help select door hardware sets.

Deadlock (push/pull)

No lock (push/pull)

Lock

Lock

Lock

Lock

No lock (push/pull)

Lock

Lock

Latch

Lock

Latch

Bathroom

Bathroom

Panic hardware

Nightlatch

1. A guide for selecting door hardware

As market leaders, you would expect Allgoodto be the most dedicated supplier in terms oftesting and certification of its products tomeet all standards.

Every essential piece of ironmongery hasbeen rigorously tested by independentNAMAS-approved test houses, whether it befor fire rating, corrosion resistance, strengthor durability. All products have beenincorporated in successful fire tests andassessed to BS476 Pt 22 (30, 60 and 120minutes) and BS EN 1634 (30 and 120minutes).

Our customers can be assured that whereverrelevant our products have been designedand tested to exceed the requirements of thenew stringent EN Standards for productperformance and we are happy to provideyou with full copies of these independenttest reports.

Where necessary, design amendments havebeen made to ensure that every productmeets the ultimate criteria. This enablesAllgood to offer a minimum ten-yearwarranty on its products.

Every product is supplied with a certificate ofauthenticity, verifying its performancetesting, and the mark, stamped on itemsfrom hinges to cylinders, is your assurance ofproduct excellence.

Allgood prides itself on being unconfined indesign concept, aspirational in productdevelopment but always meticulous inimplementation.

– the hallmark of excellence.

Standards 3. Special needs fittings for WC facilitiesThe following are examples from BS 8300. The standard itselfhowever lists many more specific situations in detail and shouldbe consulted if in doubt.

Free information about the Act can be obtained by contacting theDDA helpline:Telephone: 0345 622 633

The Code and information about the Act are also available inalternative formats or via the Internet (http://www.dfee.gov.uk)

1000720–740

480

600

750

1050

680

1100

1400

2500

2700

500 200

250

400min

600

Bath transferseat

Towel rail

Door positionallowing transferthrough doorway

Verticalgrab bars

Horizontalgrab barmounted oncranked wall

1500 x 1500wheelchairturning space

Rear support

rail

Pull down

rail

Verticalgrabbar

Two clotheshooks at 1050mm& the other one at

1400mm abovethe floor

550max

19mm ø return to door lever

19mm ø pull handle to help close doorbehind user

1000720–740

480

600

750

680

1100

2200

2400

1400 1000

150 150320320

750

750

Drop down rails

Towel rail

Two clotheshooks(1050mm& 1400mm)

Mirror

1500x1500wheelchairturning space

19mm ø return to door lever

19mm ø pull handle to help close doorbehind user

Verticalgrabbar

Verticalgrabbar

(600mm)

Verticalgrab bars (600mm)

Bathroom for independent use incorporating acorner WC.

Unisex accessible peninsular WC for assisted use.

wallchart

All information and details in this brochure are correct at time of going to press. However, Allgood plc reserves the right to change the product specifications without notice.

, , sembla, , , , andare registered trademarks.

© Allgood plc. 07/02

Allgood plce-mail: [email protected]: www.allgood.co.uk

297 Euston Road London NW1 3AQTelephone 020 7387 9951Facsimile 020 7380 1232

63/83 Brearley StreetBirmingham B19 3NTTelephone 0121 359 4415Facsimile 0121 359 5832

28 Queen StreetManchester M2 5HXTelephone 0161 834 6717Facsimile 0161 834 6839

13 Newton Place Glasgow G3 7PRTelephone 0141 332 2454Facsimile 0141 331 2729

121 Donegall RoadBelfast BT12 5JLTelephone 028 9023 2072Facsimile 028 9032 2020

Allgood Worldwide Ltd

Telephone +44 (0)20 7255 9330Facsimile +44 (0)20 7383 7950e-mail: [email protected]: www.allgoodww.com

*It is usually required that fire rated doors be self-closing and have theappropriate fire door signage. Non-fire doors need not have either of theseitems.

The door type shown below includes the latch Configuration,see overleaf for more details on the latch Configuration.

The door type shown below includes the lock Configuration,see overleaf for more details on the lock Configuration.

The door type shown below includes the deadlock Configuration,see overleaf for more details on the deadlock Configuration.

The door type shown left includes the nightlatch Configuration,see overleaf for more details on the nightlatch Configuration.

The door type shown left includes the bathroom Configuration,see overleaf for more details on the bathroom Configuration.

The grab rails, support rails & lift-up rails illustrated in the diagram (in white) can be selected in the “Special Needs fittings”section overleaf.

section 1.qxd p1

Documents