section a4 - cardinal › wp-content › uploads › 2018 › ...2 effective october 2014 200 300...
TRANSCRIPT
www.cardcompro.com
SECTION A4SERIES 200, 300 AND 500 SPECIALTY DOORS
TABLE OF CONTENTS
Features .............................................................................................................2-3
Series 200 Entrance .............................................................................................. 4
Series 300 Entrance .............................................................................................. 5
Series 500 Entrance .............................................................................................. 6
SpecificationsforSeries200,300,and500EntranceDoors ........................ S1-S4
2 www.cardcompro.com Effective October 2014
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
CD203 Beveled Hinge Stile(Series 200 shown)
(4) AF10-3#10-32 x 3/4" FHP SMS
CD400Bottom Rail
CD100-7Heavy Duty Slide-in Interlocking Corner Block AF32-1
5/16-18 x 3/4" Flange Head Cap Screw
CDH-21 5/16"-18 Zinc Plated Square Nut
Adjustable Astragal Allows for Adjustment to Ensure Alignment and Reduce Air Infiltration
CDH-104 SSCone Spring at
Adjustment Screws
CD202Adjustable Astragal
AF8-2 POH SSSelf Drilling
Adjustment Screw
MEETING STILESfor Door Pair
CD204Lock Stile
AdjustableAstragal
Double Weather Stripping
ACTIVE LEAF LOCK STILEfor Door Pair
CD204Active Stile
CD204Active Stile
CD205Inactive Stile
Cardinal Commercial Products door styles: • Series 200 Narrow Stile • Series 300 Medium Stile • Series 500 Wide StileAll aluminum entrance doors featuremechanically connected corner construction allowing for excellent structuralstrength and integrity.Thesemechanically fastened corners remain rigid and squarewithout sagging.All doors arebackedbyaLifetime Limited Warranty.
CardinalDoorsareavailableinawiderangeoffinishesincludingclearandbronzeanodizedandamultitudeofcustompowdercoatedcolors.
Effective October 2014 www.cardcompro.com 3
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
Active Stile includes 3 point Lock:CDH-32 (84" DOH) or CDH-33 (96" DOH)
Inactive Stiles includesTop and Bottom Flush Bolts:CDH-53 (84" DOH) or CDH-53 & CDH-54 (96" DOH)
96" D.O.W.
60" Inactive 36" Active
CDH-13 (84" DOH) or CDH-14 (96" DOH)Continuous Geared Hinge
CF450-34 (Shown) orCF451-35 (Similar)
SHOWROOM DOORS
CF200-3CF200-3
Series 200 Narrow Stile shownSeries 300 Medium Stile and Series 500 Wide Stile are similar
Inactive Stiles includes:CDH-109 Spring loaded caster
96" D.O.W.
60" Bi-Fold 36" Active
30"30"
CF200-3CF200-3
CF450-34 (Shown) orCF451-35 (Similar)
CF450-34 (Shown) orCF451-35 (Similar)
CF200-3CF200-3
Series 200 Narrow Stile shownSeries 300 Medium Stile and Series 500 Wide Stile are similar
BI-FOLD DOORS
4 www.cardcompro.com Effective October 2014
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
21 / 4"
1 / 2"
4"1 / 2
"
4"1 / 2
"
7"1 / 2
"
91 / 2"
1 / 2"
129/32"129/32" 1/2"1/2"
21/8"1/2" 21/8"1/2"3/16"
21/8"1/2" 21/8"1/2"3/16"
Hinge Stile(Geared Hinge Only)
Bi-fold Stiles(Geared Hinge Only)
Hinge Stile(Geared Hinge Only)
Meeting Stiles
CD207CD207 CD207 CD207 CD204CD205CD202
NOTE: CD400 Top Railfor Series 200 withCOC and Offset Armrequires a special glass size
CD100-5 spacer required for Offset Arm
Top RailTop Rail(COC with Offset Arm)
(Optional Bottom Rails)
Bottom Rail
Bottom Rail
ADA approvedBottom Rail
CD100-1(TYP)
GSK-5(TYP)
CD100-8& GSK-6
CD400
CD400 CD700 CD950
CD225
SERIES 200 SPECIALTY NARROW STILE
SHOWROOM DOORS BI-FOLD DOORS
1
1 32 4
6A
55A
6
6B
3 4
6
5
13
42
6
5
Effective October 2014 www.cardcompro.com 5
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
CD100-4 spacer required for Center PivotCD100-5 spacer required for Offset Arm
4"1 / 2
"
4"1 / 2
"
7"1 / 2
"
91 / 2"
1 / 2"
SERIES 300 SPECIALTY MEDIUM STILE
SHOWROOM DOORS BI-FOLD DOORS
CD100-1(TYP)
GSK-5(TYP)
CD400
CD700 CD950
CD400
Top RailTop Rail(COC with Offset Arm)
Bottom Rail
ADA approvedBottom Rail(Optional)
317/32"317/32" 1/2"1/2"
33/4"1/2" 33/4"1/2"3/16"
317/32"1/2" 317/32"1/2"3/16"
Hinge Stile(Geared Hinge Only)
Bi-fold Stiles(Geared Hinge Only)
Hinge Stile(Geared Hinge Only)
Meeting Stiles
CD307CD307 CD307 CD307 CD304CD305CD202
13
42
6
5
1
1 2 3 4
6
5 5A
6A
3 4
6
5
6 www.cardcompro.com Effective October 2014
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
Top RailTop Rail(COC with Offset Arm)
Bottom Rail
ADA approvedBottom Rail(Optional)
SHOWROOM DOORS BI-FOLD DOORS
SERIES 500 SPECIALTY WIDE STILE
CD100-4 spacer required for Center PivotCD100-5 spacer required for Offset Arm
4"1 / 2
"
4"1 / 2
"
7"1 / 2
"
91 / 2"
1 / 2"
CD100-1(TYP)
GSK-5(TYP)
CD400
CD700 CD950
CD400
425/32"425/32"1/2"
1/2" 5"1/2" 5" 1/2"3/16"
425/32"1/2" 425/32"1/2"3/16"
Hinge Stile(Geared Hinge Only)
Bi-fold Stiles(Geared Hinge Only)
Hinge Stile(Geared Hinge Only)
Meeting Stiles
CD507
CD507 CD507
CD507 CD504CD505CD202
13
42
6
5
1
1 3 4
2
6
55A
6A
3 4
6
5
Effective October 2014 www.cardcompro.com 7
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4CardinalCommercialProducts
Aluminum Storefront SystemsSERIES 200, 300 and 500 DOORS
GUIDE SPECIFICATIONS
SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONTSThis suggested guide specification has been developed using the current edition of the Construction Specifications Institute (CSI) “Manual of Practice,” including the recommendations for the CSI 3 Part Section Format and the CSI Page Format. Additionally, the development concept and organizational arrangement of the American Institute of Architects (AIA) MASTERSPEC Program was recognized in the preparation of this guide specification. Neither CSI nor AIA endorse specific manufacturers and products. The preparation of the guide specification assumes the use of standard contract documents and forms, including the “Conditions of the Contract,” published by the AIA.
PART 1 – GENERAL
1.01 Summary A. SectionIncludes:CardinalCommercialProductsaluminumentrancedoors,includingglassandglazing,doorhardwareandcomponents. 1. TypesofCardinalCommercialProductsEntrances: a. [200]SwingDoor;Narrowstile,2-1/8”verticalfacedimension,1-3/4”depth. b. [300]SwingDoor;Mediumstile,3-3/4”verticalfacedimension,1-3/4”depth. c. [500]SwingDoor;Widestile5”verticalfacedimension,1-3/4”depth.
EDITOR NOTE: BELOW RELATED SECTIONS ARE SPECIFIED ELSEWHERE. HOWEVER, CARDINAL COMMERCIAL PRODUCTS RECOMMENDS SINGLE SOURCE RESPONSIBILITY FOR ALL OF THESE SECTIONS AS INDICATED IN 2.07: SOURCE QUALITY CONTROL. B. RelatedSections: 1. Section08450–AllGlassEntrances 2. Section08491–SlidingDoors 3. Section08491–AluminumMallSlidingDoors 4. Section08520–AluminumFramedWindowWall 5. Section08700–FinishHardware 6. Section08900–CurtainWallSystems
1.02 References(IndustryStandards) EDITOR NOTE: REFER TO INDEX FOR ANY AND ALL APPLICABLE STANDARDS.
1.03 System Description A. EntrancePerformanceRequirements: 1. AirInfiltration:Forsingleactingoffsetpivotorbutthungentrancesintheclosedandlockedposition,thetestspecimenshallbetestedin accordance withASTM E 283 at a pressure differential of 6.24 PSF for a single door and 1.567 PSF for a pair.A single 3’0” x 7’0” entrancedoorandframeshallnotexceed0.50CFMperlinearfootofperimetercrack.Apairof6’0”x7’0”entrancedoorsandframeshallnot exceed1.0CFMperlinearfootofperimetercrack. 2. DoorCornerConstruction:Manufacturershallprovidealimitedlifetimewarrantyforthelifeofthedoorundernormaluse.
1.04 Submittals A. General:Prepare,review,approve,andsubmitspecifiedsubmittalsinaccordancewith“ConditionsoftheContract”andDivision1Submittals Sections.Productdata,shopdrawings,samples,andsimilarsubmittalsaredefinedin“ConditionsoftheContract.” B. QualityAssurance/ControlSubmittals. 1. TestReports:Submitcertifiedtestreportsshowingcompliancewithspecifiedperformancecharacteristics.
1.05 Warranty A. ProjectWarranty:Referto“ConditionsoftheContract”forprojectwarrantyprovisions. B. Manufacturer’sProductWarranty:Submit,forOwner’sacceptance,manufacturer’swarrantyforentrancesystemasfollows: 1. WarrantyPeriod:Two(2)yearsfromDateofSubstantialCompletionoftheprojectprovidedhoweverthattheLimitedWarrantyshallbegin innoevent later thansixmonths fromdateofshipmentbyCardinalCommercialProducts. Inaddition,doorcornerconstructionshallbe supportedwithalimitedlifetimewarrantyforthelifeofthedoorundernormaluse.
1.06 Quality Assurance A. Qualifications: 1. InstallerQualifications:Installerexperienced(asdeterminedbycontractor)toperformworkofthissectionwhohasspecializedintheinstallation ofworksimilartothatrequiredforthisprojectandwhoisacceptabletoproductmanufacturer. 2. ManufacturerQualifications:Manufacturercapableofprovidingfieldservicerepresentationduringconstruction,approvingacceptableinstaller andapprovingapplicationmethod. B. Pre-Installation Meetings: Conduct pre-installation meeting to verify project requirements, substrate conditions, manufacturer’s installation instructions,andmanufacturer’swarrantyrequirements.
S1
8 www.cardcompro.com Effective October 2014
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
1.07 Delivery, Storage, and Handling A. Ordering:Complywithmanufacturer’sorderinginstructionsandlead-timerequirementstoavoidconstructiondelays. B. Packing,Shipping,Handling,andUnloading:Delivermaterialsinmanufacturer’soriginal,unopened,undamagedcontainerswithidentification labels intact. C. StorageandProtection:Storematerialsprotectedfromexposuretoharmfulweatherconditions.Handleentrancedoorsandcomponentsto avoiddamage.Protectentrancedoorsagainstdamagefromelements,constructionactivities,andotherhazardsbefore,duringandafter entranceinstallation.
PART 2 – PRODUCTS
EDITOR NOTE: RETAIN BELOW ARTICLE FOR PROPRIETARY METHOD SPECIFICATION; ADD PRODUCT ATTRIBUTES, PERFORMANCE CHARACTERISTICS, MATERIAL STANDARDS, AND DESCRIPTIONS AS APPLICABLE. DO NOT USE THE PHRASE “OR EQUAL” / “OR APPROVED EQUAL,” OR SIMILAR PHRASES. USE OF SUCH PHRASES MAY CAUSE AMBIGUITY IN THE SPECIFICATIONS DUE TO OF DIFFERENT INTERPRETATIONS AMONG THE DIVERGENT PARTIES OF THE CONSTRUCTION PROCESS AND READERS OF THE SPECIFICATIONS. SUCH PHRASES REQUIRE EXTENSIVE AND COMPLETE REQUIREMENTS (PROCEDURAL, LEGAL, REGULATORY, AND RESPONSIBILITY) FOR DETERMINING “OR EQUAL.”
2.01 Manufacturers(AcceptableManufacturers/Products) A. AcceptableManufacturers: 1. Address:CardinalCommercialProducts,LLC 4915HellerStreet Louisville,KY40218 ContactNumbers: a.Telephone:502-969-4059 b.Fax: 502-813-2484 c.Email:[email protected] d.WebAddress:cardcompro.com 2. ProprietaryProduct(s)/System(s)CardinalCommercialProducts a.Series:[(200)(300),or(500)]SwingDoors(Select)Finish/Color:(See2.06Finishes) b.Finish/Color:(See2.06Finishes)
EDITOR NOTE: RETAIN BELOW FOR ALTERNATE MANUFACTURERS/PRODUCTS AS SPECIFIED IN THE CONTRACT DOCUMENTS. COORDINATE BELOW WITH BID DOCUMENTS (IF ANY), AND DIVISION 1 ALTERNATES SECTION. CONSULT WITH CARDINAL COMMERCIAL PRODUCTS FOR RECOMMENDATIONS ON ALTERNATE MANUFACTURERS AND PRODUCTS MEETING THE DESIGN CRITERIA AND PROJECT REQUIREMENTS. CARDINAL COMMERCIAL PRODUCTS RECOMMENDS OTHER MANUFACTURERS REQUESTING APPROVAL TO BID THEIR PRODUCT AS AN EQUAL, MUST SUBMIT THEIR REQUEST IN WRITING (10) DAYS PRIOR TO CLOSE.
B. Alternate(Manufacturers/Products):Inlieuofprovidingbelowspecifiedbasebid/contractmanufacturer,providebelowspecifiedalternatemanufacturers. RefertoDivision1AlternatesSection. 1. BaseBid/ContractManufacturer/Product:CardinalCommercialProducts a. Product:AluminumEntrances b. Series:[(200)(300),or(500)]SwingDoors(Select) c. ProductAttributes: 2. EntranceMemberProfiles 3. Alternate#____Manufacturer/Product: a. Product: b. Series: c. ProductAttributes: 4. Alternate#___Manufacturer/Product: a. Product: b. Series: c. ProductAttributes:C. Substitutions: 1 General:RefertoDivision1Substitutionsforproceduresandsubmissionrequirements. a. Pre-Contract(BiddingPeriod)Substitutions:Submitwrittenrequeststen(10)dayspriortobiddate. b. Post-Contract(ConstructionPeriod)Substitutions:Submitwrittenrequestinordertoavoidentranceinstallationandconstructiondelays. 2. SubstitutionDocumentation: a. ProductLiteratureandDrawings:Submitproductliteratureanddrawingsmodifiedtosuitspecificprojectrequirementsandjobconditions. b. Certificates: Submit certificate(s) certifying substitutemanufacturer (1) attesting to adherence to specification requirements for entrance systemperformancecriteria. c. TestReports:Submittestreportsverifyingcompliancewitheachtestrequirementrequiredbytheproject. d. ProductSampleandFinish:Submitproductsample,withspecifiedfinishandcolor. 3. SubstitutionAcceptance:Acceptancewillbeinwrittenform,eitherasanaddendumormodification,anddocumentedbyaformalchangeorder signedbytheOwnerandContractor.
S2
Effective October 2014 www.cardcompro.com 9
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
2.02 Materials A. Aluminum(EntrancesandComponents): 1. MaterialStandard:ASTMB221;A96063-T6and/orA95050-H32alloyandtemper 2. Thedoorstileandrailfacedimensionsofthe[________](chooseone:[(200)(300)(500)]entrancedoorwillbeasfollows)
3. Majorportionsofthedoormemberstobe0.125”nominalinthicknessandglazingmoldingtobe0.05”thick. 4. Tolerances: Reference to tolerances for wall thickness and other cross-sectional dimensions of entrance members are nominal and in compliancewithAluminumStandardsandData,publishedbyTheAluminumAssociation. B. GlazinggasketsshallbeEPDMelastomericextrusions C. Provideadjustableglassjacktohelpcentertheglassinthedooropening.
2.03 Accessories A. Fasteners:Whereexposed,shallbealuminum,stainlesssteelorplatedsteel. PerimeterAnchors:Aluminum.When steel anchors are used, provide insulation between steel material and aluminummaterial to prevent galvanicaction.
EDITOR NOTE: REVISE BELOW FOR SPECIFIC HARDWARE FOR EACH SPECIFIC ENTRANCE TYPE. TO INSURE SINGLE SOURCE RESPONSIBILITY AND TIMELY COORDINATION, CARDINAL COMMERCIAL PRODUCTS RECOMMENDS THAT YOUR FINISH HARDWARE REQUIREMENTS BE INCLUDED IN THIS SECTION. IF THESE REQUIREMENTS MUST BE FURNISHED UNDER THE “FINISH HARDWARE” SECTION OF THE SPECIFICATIONS, THE FOLLOWING STATEMENT SHOULD BE INCLUDED. “THE FINISH HARDWARE SUPPLIER SHALL BE RESPONSIBLE FOR FURNISHING PHYSICAL HARDWARE TO THE ENTRANCE MANUFACTURER PRIOR TO FABRICATION, AND FOR COORDINATING HARDWARE DELIVERY REQUIREMENTS WITH THE HARDWARE MANUFACTURER, THE GENERAL CONTRACTOR AND THE ENTRANCE MANUFACTURER TO INSURE THE BUILDING PROJECT IS NOT DELAYED.” IF LOCK CYLINDERS FOR ALUMINUM DOORS ARE TO BE MASTER-KEYED, IT IS SUGGESTED THAT CYLINDERS BE INCLUDED UNDER THE “FINISH HARDWARE” SECTION OF THE SPECIFICATIONS.
C. StandardEntranceHardware 1. Weather-stripping: a. Meetingstilesonpairsofdoorsshallbeequippedwithaspring-loadedadjustableastragalwithadoublerowofwoolpileweather-stripping. Gapsinweatheringatlocklocationofmeetingstileondoorpairshallnotbeallowed. b. The doorweathering on a single acting offset pivot or butt hung frame (single or pairs) shall havewool pile or EPDMbulb gasket (Necessarytomeetspecifiedperformancetests.) 2. BottomDoor Sweep: EPDM blade gasket sweep strip in an aluminum extrusion applied to the interior exposed surface of the bottom railwithconcealedfasteners.(Note:BottomDoorSweepsarerequiredtomeetspecifiedperformanceforairinfiltration) 3. Threshold:Extrudedaluminum,onepieceperdooropening,withribbedsurface. 4. CenterPivots:[__________]. 5. OffsetPivots:[__________]. 6. ButtHinge:[____________]. 7. ContinuousGearHinge:[_________]. 8. Push/Pull:[___________]style. 9. PanicDevice:[___________]. 10.Closer:[______________]. 11. SecurityLock/DeadLock:ActiveLeaf[___________];InactiveLeaf[___________]. 12.LatchHandle:[___________]. 13.Cylinder(s)/Thumb-turn:[_____________]. 14.ElectricStrike/StrikeKeeper:[____________].
2.04 Related Materials A. Sealants:RefertoJointTreatment(Sealants)Section. B. Glass:RefertoGlassandGlazingSection.
2.05 Fabrication A. EntranceSystemFabrication: 1. Doorcornerconstructionshallconsistofaninterlockingslide-instabilizercornerblock,mechanicallyfastenedtodoorstilewith5/16”diameter boltsthreadedintosteelsquarenutback-upplates.Topandbottomrailsaremechanicalattachedtocornerblocksatallfourcornerswith #10x3/4”steelfasteners.GlazingstopsshallbecompressionfittypewithEPDMglazinggaskets. 2. Accuratelyfitandsecurejointsandcorners.Makejointshairlineinappearance. 3. Preparecomponentswithinternalreinforcementfordoorhardware. 4. Arrangefastenersandattachmentstoconcealfromview.
DoorSeries
VerticalStile
TopRail
BottomRail
ADABottom Rail
TrafficApplication
200 2¼" 4" 9½" (optional) Normal
300 4" 7" 9½" (optional) Normal toHeavy
500 4" 7" 9½" (optional) Normal toAbusive
129/32"
317/32"
425/32"
S3
10 www.cardcompro.com Effective October 2014
SERIES 200, 300 AND 500 SPECIALTY DOORS - A4
2.06 Finishes
EDITOR NOTE: SELECT BELOW FINISH AND COLOR FROM CARDINAL COMMERCIAL PRODUCTS’S STANDARD COLORS. POWDER COATINGS ARE AN EPA RECOMMENDED FINISHING METHOD FOR ARCHITECTURAL ALUMINUM AND FURTHER CONTRIBUTES TOWARDS THE “GREEN BUILDING INITIATIVE” OF THE U.S. GOVERNMENT. CUSTOM COLORS ARE AVAILABLE UPON REQUEST FROM CARDINAL COMMERCIAL PRODUCTS. OTHER POLYESTER POWDER COATINGS CONFORMING TO AAMA 2604 ARE AVAILABLE. CONSULT WITH YOUR CARDINAL COMMERCIAL PRODUCTS REPRESENTATIVE FOR OTHER SURFACE TREATMENTS AND FINISHES. A. ShopFinishing: 1. ColorAnodizingConformingtoAA-M12C22A44,AAMA608.1,ColorAnodicCoating(Color:#21DarkBronze).(Standard) 2. ClearAnodizingCoatingConformingtoAA-M12C22A31,AAMA607.1,ClearAnodicCoating(Clear#11)(Standard) 3. AAMA2605,FluoropolymerPowderCoating(Color:__________). 4. AAMA2604,PolyesterPowderCoating.(Color:__________). 5. Other:Manufacturer____________Type____________(Color__________).
2.07 Source Quality Control A. SourceQuality:Providealuminumentrancesspecifiedhereinfromasinglesource. 1. BuildingEnclosureSystem:Whenaluminumentrancesarepartofabuildingenclosuresystem, includingstorefront framing,windowwall systems,curtainwallsystemandrelatedproducts,providebuildingenclosuresystemproductsfromasinglesourcemanufacturer. B. FabricationTolerances:Fabricatealuminumentrancesinaccordancewithentrancemanufacturer’sprescribedtolerances.
PART 3 – EXECUTION
3.01 Examination A. SiteVerificationofConditions:Verifysubstrateconditions(whichhavebeenpreviouslyinstalledunderothersections)areacceptableforproduct installationinaccordancewithmanufacturer’sinstructions.Verifyopeningsaresizedtoreceiveentrancesystemandsillislevelinaccordance withmanufacturer’sacceptabletolerances.
EDITOR NOTE: COORDINATE BELOW ARTICLE WITH MANUFACTURER’S RECOMMENDED INSTALLATION DETAILS AND INSTRUCTIONS. 1. FieldMeasurements:Verifyactualmeasurements/openingsbyfieldmeasurementsbeforefabrication;showrecordedmeasurementsonshop drawings.Coordinatefieldmeasurements,fabricationschedulewithconstructionprogresstoavoidconstructiondelays.
3.02 Installation A. General:Installentrancesysteminaccordancewithmanufacturer’sinstructionsandAAMAstorefrontandentranceguidespecificationsmanual. 1. Attachtostructuretopermitsufficientadjustmenttoaccommodateconstructiontolerancesandotherirregularities. 2. Providealignmentattachmentsandshimstopermanentlyfastensystemtobuildingstructure. 3. Alignassemblyplumbandlevel,freeofwarpandtwist.Maintainassemblydimensionaltolerancesaligningwithadjacentwork. 4. Setthresholdsinbedofmasticandsecure. 5. Adjusting:Adjustoperatinghardwareforsmoothoperation. B. RelatedProductsInstallationRequirements: 1. Sealants(Perimeter):RefertoSection7JointTreatment(Sealants). 2. Glass:RefertoSection8GlassandGlazing. a. Reference:ANSIZ97.1,CPSC16CFR1201andGANAGlazingManual.
3.03 Cleaning and Protection A. Cleaning:Removetemporarycoveringsandprotectionofadjacentworkareas.Repairorreplacedamagedinstalledproducts.Installedproducts mustbecleanedinaccordancewithmanufacturer’sinstructionspriortoowner’sacceptance.Removeconstructiondebrisfromprojectsiteand legallydisposeofdebris. B. Protection:Protectinstalledproduct’sfinishsurfacesfromdamageduringconstruction.Protectaluminumentrancesfromdamagefromgrinding andpolishingcompounds,plaster,lime,acid,cement,orotherharmfulcontaminants.Removeandreplacedamagedaluminumentrancesatno extracost.
DISCLAIMER STATEMENT Thisguidespecificationistoonlybeusedbyqualifiedconstructionspecifiers.Theguidespecificationisnotintendedtobeverbatimasaproject specification without appropriate modifications for the specific use intended. The guide specification must be used and coordinated with the proceduresofeachdesignfirm,andtheparticularrequirementsofaspecificconstructionproject.
END OF SECTION 08410
S4