security systems bu communication systemsdcn st/seu-co 1 stand alone camera control 09.12.2004 how...
TRANSCRIPT
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 1
How to configure Stand Alone Camera Control
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 2
This presentation is intended to guide the installer step by step through camera control installation.
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 3
Standalone DCN system with Camera Control
• Direct Camera Control
• With Allegiant Video Switcher
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 4
Direct Camera Control (Stand Alone)
Requirements :
• One Dome Camera
• One Monitor
• CCU with TCB4
• DCN software V9.30 or higher!!!
• Temporary installation PC
• Software LBB3562 V2.0 or higher!!!
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 5
Step 1 Connect PC and Monitor to Dome Camera
Temporary PCwith one ComportTemporary PCwith one Comport
RS232 AutoDome
Camera
Make sure that the Dome camera has an address.
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 6
Step 2Install virtual keyboard software LTC 5138/00
Virtual KeyboardProgram
Virtual KeyboardProgram
Temporary PCwith one ComportTemporary PCwith one Comport
RS232 AutoDome
Camera
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 7
Step 3Configure Virtual Keyboard
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 8
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 9
Make sure you choose the right camera!!
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 10
Camera nr = Camera Address
Keep in mind !!
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 11
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 12
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 13
Step 4Set Pre-Positions
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 14
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 15
Repeat Step 4 to set all Pre-Positions
Set the highest Pre-Position as overview
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 16
Step 5Check the Pre-Positions
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 17
If you were not successful setting up the pre-positions please don’t continue with the next steps.
First make sure that the pre-positions are set.
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 18
DCN CCU Temporary PCwith one ComportTemporary PCwith one Comport
LBB 3500/x5
RS232
Step 6 Connect CCU to PC
Baudrate 9.6K
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 19
Step 7Change baudrate of CCU
Now you have to change the baudrateof Port 1(on the CCU) to 9.6K!!
Port 1Protocol = Camera ControlBaudrate = 9.6K
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 21
If you are using the LBB3500/15 or /35 make sure you connect the RS232 cable to Port 2.
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 22
DCN CCU
Camera Control Program
Camera Control Program
Temporary PCwith one ComportTemporary PCwith one Comport
LBB 3500/x5
RS232
Step 8Install Camera Control Software LBB3562
Baudrate 9.6K
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 23
Make sure you choose the configuration without Allegiant Video Switcher
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 24
Step 9Start Camera Installation software
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 25
Step 10Combine seat numbers with
camera pre positions
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 26
Make sure you choose the right camera!!Camera nr = Camera Address
Keep in mind !!
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 27
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 28
5
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 29
DCN CCU
AutoDomeCameraRS232
Step 11Connect CCU to AutoDome Camera
Baudrate 9.6KBaudrate 9.6K
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 30
© Robert Bosch GmbH reserves all rights even in the event of industrial
property rights. We reserve all rights of disposal such as copying and
passing on to third parties.
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 31
With use of Allegiant Video Switcher
Requirements :
• Allegiant switcher
• Video Switcher keyboard
• Fixed and /or AutoDome cameras
• Monitor(s)
• DCN software V8.00 or higher
• Temporary installation PC with two Comports
• Software LBB3562 V1.0 or higher
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 32
If you have DCN software V9.30 or higherthen you need LBB3562 V2.0 or higherOtherwise it will not work.
Keep in mind
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 33
Step 1Connect Camera(s),Monitor(s) and Keyboard
to Video Switcher
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 34
Step 2Connect PC to Allegiant Switcher and CCU
DCN CCU Allegiant SwitcherAllegiant SwitcherRS232 RS232
Temporary PCwith two ComportsTemporary PC
with two Comports
Baudrate 19.2K Baudrate 19.2K
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 35
The default COM port settings are:
Com 1 for communication with the CCU Com 2 for communication with the Video Switcher
Keep in mind !!
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 36
Step 3CCU protocol and Serial Port settings
Make sure that the port you use of the CCU is set to :
Protocol = Camera ControlBaudrate = 19.2K
LBB3500/05
The default setting for the LBB3500/05 is :
Port 1Protocol = Camera ControlBaudrate = 19.2K
Keep in mind !!
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 37
LBB3500/15 & LBB3500/35
The default settings for the LBB3500/15 &LBB3500/35 is :
Port 1Protocol = FullBaudrate = 115.2K
Port 2Protocol = Camera ControlBaudrate = 19.2K
Keep in mind !!
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 38
If you are using the LBB3500/15 or /35 make sure you connect the RS232 cable to Port 2.
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 39
Step 4Install Camera Control software LBB3562
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 40
Make sure you choose the configuration with Allegiant Video Switcher
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 41
Step 5Start Camera Installation software
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 42
Step 6Set Pre-Positions using the Video Switcher Keyboard
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 43
Step 7Combine seat numbers with
camera pre positions
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 44
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 45
5
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 46
Step 8Connect CCU to Allegiant Video Switcher
DCN CCU Allegiant SwitcherAllegiant SwitcherRS232
Baudrate 19.2K Baudrate 19.2K
Security Systems BU Communication Systems
Stand Alone Camera Control09.12.2004 DCNDCN ST/SEU-CO 47
How to configure Stand Alone Camera Control
End of section
Robert Bosch GmbH
All rights are reserved. Reproduction or passing on to
third parties in whole or in parts is prohibited without the
written consent of the copyright owner.