series rrgg6600blkegypt.com/wp-content/uploads/2017/08/rg60.pdf · 4 june 2012 rg60 catalogue * the...
TRANSCRIPT
SERIES RGRG6060TECHNICAL CATALOGUETECHNICAL CATALOGUE
Edition June 2012Edition June 2012
3
www.balkan.gr
RG60 Catalogue
1 Catalogue cover
3 Catalogue pages – Overview
4 Design Description
5 System Description
6 System Description
7 Design Description
8 Table Composite Profi les, Table Profi les and Table Profi les for Accessories
9 Table Corner Connectors and Table T-Connectors
10 Table Accessories, Table Gaskets and Table Installation Material
11 Cross Section Values
12 Cross Section Values
13 Explanations regarding the U-Values Table
14 Design Values Table/U-Values Table 30%
15 U-Values Table 20%
16 Nomimal Values of the Heat Transfer Coeffi cient Uf
17 Profi les
18 Profi les
19 Profi les
20 Profi les
21 Profi les
22 Profi les
23 Profi les
24 Profi les
25 Profi les
26 Profi les
27 Profi les
28 Additional profi les
29 Corner profi les
30 Corner profi les
31 Corner connectrors for variable corners
32 Corner connectrors for variable corners
33 T-connector profi les
34 Glazing Beads
35 Glazing Table
36 Corner Connectors
37 Corner Connectors
38 Moving Corner Connectors
39 Corner Connectors
40 T- Connectors
41 T- Connectors
42 T- Connectors
43 T- Connectors
44 Accessories
45 Accessories
46 Sections Overview
47 Sections Overview
48 Sections Overview
49-79 Sections
80-102 Cutting dimensions
104-167 Working pages
4
June 2012
RG60 Catalogue
* The installation depths indicated in the catalogue are reference dimensions for planning. The manufactured dimensions for frame and sash profi les are 0.4 mm above the nominal dimensions in the catalogue, the transom profi les 0.2 mm.
Windows: Heat-insulated composite profi le system with voluminous EPDM multi-chamber center seal with preformed angles. Increased heat insulation with glazing seal seated on the rebate ground. Uf values according to EN ISO 10077. Design values Uf,BW acc. to DIN V 4108-4: 2002.
Doors: Heat-insulated composite profi le system for single- or double-leafed doors, optionally without additional center rebate post profi le, inward and outward opening door leafes. Design in panic function acc. to EN 1125 and emergency exit function acc. to EN 179 possible. The window profi les can be integrated with all performance characteristics.
Fittings: Commercially available fi ttings.
The profi les are implemented with a 10 mm Euro-groove. Increased burglar protection possible due to WK 3 safety class. It is possible to equip the doors with butt hinges or with mulitpart, fi tted hinges.
Design: Double wall, hollow composite profi les (three-chamber system) with even surfaced rebate bed. Dimensions*: Frame profi les: 60 mm installation depth (basic depth); window sashes 70 mm installation depth.Profi le compound: Quality controlled, form-fi tting and tensionally locked compound with at least 25% glass-fi bre reinforced polyamide webs with melted wire inserts. The hollow composite profi les are suitable for subsequent surface working.
Air permeability of joints and Watertightness under heavy rain:Exposure Category C acc. to DIN 18055
5
www.balkan.gr
RG60 Catalogue
The glazing rebate is additionally shielded against thermal radiation and air convection by means of multi-chamber EPDM cover profi les at both sides of the fi lling.The given nominal values of the heat transmission coeffi cient Uf of 2,1 W/m2 K to3,1 W/m2 K for individual profi les and profi le combinations are given in separate tables and documented by respective test certifi cates issued by the Institute for Windows Technology in Rosenheim, registered association.
3. Design3.1 Maximal sash sizesWindows: Sash width 380 - 1600 mm Sash height 600 - 2400 mm max. sash weight: 130 kg additional center locking points for sash heights or widths exceeding 1250 mm.Parallel-slide-and-tilt-doors: 1680 x 2200 mm from sash profi le RG 1220 max. sash weight: 150 kgDoors: 1300x2300 mm max. sash weight: 120 kg3.2 StaticsThe section properties of the profi les (inertia moment and section modulus, etc.) are given in separate statics tables.3.3 Frame and glazing bar connectionThe corner and T-connections of the profi les in both cavities are made with glued in, aluminium corner or T-connectors, which are fi xed with roll pins or with mechanical corner-connection machines.Water tightness at mitres and joints must be ensured by the processor. This applies especially in regard to the lower horizontal frame and glazing bar profi les.All orifi ces at corner and T-connections (continuous grooves of the glazing rebate webs, clamping grooves in the rebate bed, etc.), surfaces of base profi les facing the frame profi le, etc., must be sealed with special care (in thin layers as well) with suitable fl exible silicone and thiokol sealants. 3.4 Center sealEPDM center seal serving as frame with 50 mm preformed angles. Gluing with the preformed angles is effected with contact adhesive 905 410 (cyanoacrylate adhesive). The cut of the seal profi le is calculated as follows:Sash measure minus 100 mm(2 x 50 mm preformed angle)plus 0.5 %. Example: Sash measure 1100 mm. Center seal cut = 1100-100 + 5= 1005 mm.
System Description
1. GeneralThis profi le system includes heat-insulated, two-wall composite profi les (three-chamber system) for the production of windows and doors.Heat insulation is achieved by thermal separation of the inner and outer profi le walls by means of glass-fi bre reinforced isolating webs made of polyamide, with special melted wire inserts. In a quality controlled process, the form-fi tting and tensionally locked compound is created in the pressing plant.The design is in accordance with the state of the art and the directives and recommendations of the insulating glas, fi ttings and sealing materials manufacturers and meets the requirements of the “Directive for the Proof of Stability of Composite Metal-Plastic Profi les” of the German Institute for Construction Engineering,Berlin, as well as the requirements of the provisions regarding quality and testing of aluminium windows.The Uf values of the profi les and profi le combinations have been determined acc. to EN ISO 10077 and are given acc. to DIN V 4108-4: 2007 in design values.The air permeability of joints and watertightness under heavy rain of the windows correspond to the exposure category C of DIN 18055.The construction of solid, safe and operational elements is guaranteed. The “Code of Practice for the Processor” in our latest main catalogue must be observed for the use and processing of our design. With our delivery of composite profi les you are also receiving our guarantee for this product.
2. System ScopeThis profi le system includes window and door profi les for the construction of side-hung, turn and tilt, tilt and double sash windows, doors and parallel-slide-and-tilt doors. The main profi les include narrow and wide outer frame, sash, glazing bar, post and sill rail profi les.Additional profi les are respectively available for wall connections, as well as for expansion and decorative glazing bars. Glazing rebate strips for fi lling thicknesses (glazing thicknesses) from 18 to 34 mm are available.2.1 Heat insulationThe highly heat insulated design includes frame and glazing bar profi les with a frame profi le depth of 75 mm and a sash profi le depth of 70 mm for windows and 60 mm for doors, equipped with a voluminous, multi-chamber EPDM center seal.
6
June 2012
RG60 Catalogue
The processor has to take care that no cold air can reach the internal shells of the frame profi les when the elements have been fi tted.This applies especially, if roller shutters are installed over the elements. In this case the face of the frame profi le must be covered with fi xed sealing strips made of HR polyurethane or polystyrene foam. Thermal bridges must be avoided.
4. Surface WorkingRegarding the surface treatment the FWB Guidelines, Edition 11/91, apply. Variable colouring of the profi les prior to bonding of the semi-shells is possible.4.1 Anodic Oxidation For the anodic oxidation of the aluminium components DIN 17611 applies. The Quality and Testing Provisions „Anodized Aluminium RAL-RG 661” must be observed by the anodic oxidation plant. The oxide layers produced by anodizing must have a minimum layer thickness of 20 μm. Special care must be applied in the case of material that is to undergo anodic axidation according to the E6 procedure (pickled and eloxated). A guarantee regarding the suitability for this procedure can only be given, if the profi les immediately after their production are delivered to the anodizing treatment plant, where they are processed immediately. In the case of deliveries from warehouse stock we do not assume any responsibility for this procedure whatsoever.4.2 Colour CoatingColour coating must be executed according to the „Provisions Regarding Qualtiy and Testing of Components RAL-RG 631”. The coating of the profi les is carried out by fi ring on of coating powders. Normally, polyester-based coating powders are used.Layer thickness should amount from 60 up to 120 μm at most. The coated profi les must be cured in a furnace at a maximal object temperature of 175° ± 10 °C and a fi ring time of about 20 minutes (after reaching object temperature).In order to ensure their faultless colour coating, the aluminium profi les must be subjected to careful pre-treatment acc. to DIN 50939. Chromating is necessary.
5. Dimensioning of the Composite Profi lesThe dimensions given in the catalogue are planning dimensions. Due to different surface treatments they cannot be used as reference dimensions for composite profi les delivered by us.
3.5 GlazingThe glazing on the sealant free rebate bed is effected with preformed EPDM seal profi les. In order to ensure ventilation (vapour pressure equalization) of the rebate space, openings are built in with a minimum cross section of 15x5 mm or 8 mm diameter placed in front of the center seal that are leading to the ambient air. The openings are located at the lowest point of the rebate and are provided at least twice in the lower horizontal. The external openings are located between frame angle and glazing spacer block, at a maximal distance of 100 mm from the angle. It is recommended to place these openings laterally and at the upper part of the profi les.The insertion of glazing spacer blocks (blocking) is effected on glazing rebate inserts of the system. The blocking does not obstruct neither air conduction nor water fl ow (condensate).If sealants are used for the glazing, the table “Exposure Categories for the Glazing of Windows” of the Institute for Windows Technology in Rosenheim, registered association, must be observed.3.6 Drainage of the DesignThe water entering into the antechamber (pressure compensation chamber) is let off via at least 2 water drain holes, with dimensions 28 x 12 mm, in front of the center seal, directly to the outside. These are located at a distance of about 120 mm from the frame end, maximal distance being 600 mm. The openings are covered with drainage inserts.In the case of downward drainage of water, directly on the window sill or over a base profi le, the entering water is let off through drain louvers, sized 35 x 6 mm. Quantity and location as described above. The respective drain louvers in the aluminium base profi le should be placed with an offset of 50 mm with regard to the louvers in the frame profi le.3.7 Condensation Water FormationThe formation of condensation water on the heat-insulated composite profi les is only possible, if under respective interior and exterior temperatures, as well as under respective interior space air humidity, the formation of condensation water (formation of respiration water) would also be observed on the respective insulating glass panes. Profi les like roller shutter guides or window sills that are fi tted additonally on the external side of the composite profi les, have a negative impact on the internal suface temperatures of these profi les and thus on the condensation water behaviour.
20
12
7,5
28
7
www.balkan.gr
RG60 Catalogue
Base Profile
Insulating web, made of glass-fibre
Frame Profile
Insulated layer from Polyurethan-hard
Central Gasket with performed
Sash Profile
Glazing Bead
Glazing Gasket Glazing Gasket outside
Glazing Spacer Block
Glazing Rebate Insert
At least 3pcs rebate drains
Antechamber or pressure
At least 2 pcs water drainage
Supplementary Profile
Windowsill
Design Description
8
June 2012
RG60 Catalogue
Order No. Designation Stock length in mDevelopment in mm
anod. anod.* mech.
AH260-5060030 Frame profi le for facade 24/56 mm 6,00 434 305 86
AH260-RG6121 Frame profi le 34/58 mm 6,00 402 324 92
AH260-RG6131 Frame profi le 44/68 mm 6,00 437 339 112
AH260-RG6211 Sash profi le 51/39 mm 6,00 436 380 90
AH260-RG6220 Sash profi le 77/65 mm 6,00 542 426 142
AH260-RG6245 Transom for sash 34/82 mm 6,00 469 391 116
AH260-RG6260 Rebate profi le 66 mm 6,00 430 354 66
AH260-RG6261 Rebate profi le 66 mm 6.00 433 359 66
AH260-RG6215 Sash profi le perimetrical locking 56/44 mm 6,00 470 387 100
AH260-RG6222 Sash profi le perimetrical locking 77/65 mm 6,00 549 422 142
AH260-RG6406 Transom/Mullion 34/82 mm 6,00 449 371 116
AH260-RG6411 Transom/Mullion 44/92 mm 6,00 489 391 136
AH260-RG6526 Transom/Mullion 44/92 mm 6.00 589 491 236
AH260-RG6301 Door frame profi le 44/70 mm 6,00 447 325 114
AH260-RG6311 Door frame profi le 70/44 mm 6,00 447 325 114
AH260-RG6330 Door sash profi le 74/72 mm 6,00 509 377 146
AH260-RG6335 Door sash profi le 44/98 mm 6,00 509 377 146
AH260-RG6350 Change profi le 50/ 6 mm 6,00 345 255 50
AH260-RG6395 Base profi le 109/133 mm 6,00 661 478 242
AH260-RG6750 Corner post profi le 75x75/ 80X80 mm 6,00 607 365 160
Composite Profi les
Order No. Designation Stock length in mDevelopment in mm
anod. mech.
AH900-TF454 Glazing bead 21mm 6,0 121 43
AH900-TF457 Glazing bead 32 mm 6,0 143 54
AH900-TF457A Glazing bead 34 mm 6,0 147 57
AH900-TF460 Glazing bead 44 mm 6,0 168 66
AH900-TF464 Glazing bead 27 mm 6,0 193 49
AH900-TF465 Glazing bead 37 mm 6,0 212 59
AH900-TF466 Glazing bead 47 mm 6,0 232 69
Profi les
Order No. Designation
AH900-TF481 Corner connector profi le, 6.0 mm 6,0
AH900-TF483 Corner connector profi le, 12,0 mm 6,0
AH900-TF495 Corner connector profi le, 16,4 mm 6,0
AH900-TF496 Corner connector profi le, 20,0 mm 6,0
AH900-TF497 Corner connector profi le, 22,8 mm 6,0
AH900-TF498 Corner connector profi le, 26,8 mm 6,0
AH900-TF499 Corner connector profi le, 30,0 mm 6,0
AH900-TF500 Corner connector profi le, 32,0 mm 6,0
AH900-TF501 Corner connector profi le, 34,0 mm 6,0
AH900-TF502 Corner connector profi le, 45,4 mm 6,0
Profi les for accessoriesOrder No. Designation
AH900-TF649 Joint for mullion 11,5Χ50
AH900-TF558 Profi le for corner 20,5mm
AH900-TF650 Joint for mullion 19,4Χ46
AH900-TF269 Addition for frame & mullion
AH900-TF292 Additional sash drainage
AH900-TF368 H for frame joining
AH900-TF403 Addition for door seal in
AH900-TF403B Addition for door seal in
AH900-TF290 Movement transmition rod
AH900-TF370 Connecting Rod
9
www.balkan.gr
RG60 Catalogue
Order No. Designation Required installation material
Profi le CodeQuantity Order No.
AE001-901440-00 Corner connector for profi les AH260-RG6211, AH260-RG6214, outside 2 pcs AE009-905140-00 AH900-TF481
AE001-901459-00 Corner connector for profi les AH260-RG6121, AH260-5060030, outside 2 pcs AE009-905150-00 AH900-TF495
AE001-901474-00 Corner connector for profi lesAH260-RG6131, outside 2 pcs AE009-905160-00 AH900-TF498
AE001-901484-00 Corner connector for profi le AH260-RG6222, outside 2 pcs AE009-905160-00 AH900-TF500
AE001-901540-00 Corner connector for profi le AH260-RG6215, inside 2 pcs AE009-905150-00 AH900-TF495
AE001-901545-00 Corner connector for profi le AH260-RG6215, outside 2 pcs AE009-905140-00 AH900-TF483
AE001-901550-00 Corner connector for profi le AH260-RG6222, inside 2 pcs AE009-905160-00 AH900-TF501
AE001-901569-00 Corner connector for profi les AH260-5060030, AH260-RG6121,AH260- RG6406, inside 2 pcs AE009-905160-00 AH900-TF496
AE001-901579-00 Corner connector for profi les AH260-RG6211,AH260-RG 6214, inside 2 pcs AE009-905160-00 AH900-TF496
AE001-901589-00 Corner connector for profi les AH260-RG6131and AH260-RG6411, inside 2 pcs AE009-905160-00 AH900-TF499
AE001-901684-00 Corner connector for profi leAH260-RG6221, inside 2 pcs AE009-905160-00 AH900-TF502
AE001-901450-00 Corner connector for profi leAH260-RG6406, outside 2 pcs AE009-905160-00 AH900-TF483
AE001-901469-00 Corner connector for profi leAH260-RG6411, outside 2 pcs AE009-905160-00 AH900-TF497
Order No. Designation Required installation material Profi le CodeQuantity Order No.
AE003-902025-00T-connector for profi les AH260-RG6245 andAH260-RG6406, outside on frame, sash and
transom glazing bar profi les1 pc AE009-905150-00 AH900-TF649
AE003-902028-00 T-connector for profi les AH260-RG6411, on frame and transom profi les 1 pc AE009-905160-00 AH900-TF649
AE003-902026-00 T-connector for profi les AH260-RG6121, outside on frame and transom profi les 1 pc AE009-905160-00 AH900-TF649
AE003-902033-00 T-connector for profi les AH260-RG6131 , outsideon frame and transom profi les 1 pc AE009-905160-00 AH900-TF649
AE003-902046-00T-connector for profi les AH260-RG6121,
AH260- RG6245 and AH260-RG6406 inside, on frame and glazing bar profi les
1 pc AE009-905160-00 AH900-TF650
AE003-902047-00T-connector for profi les AH260-RG6131,
AH260-RG6411, inside on frame and transom profi les
1 pc AE009-905160-00 AH900-TF650
AE003-902050-00 T-connector for profi les AH260-RG6395 inside on frame and transom profi les 2 pcs AE009-905160-00 AH900-TF650
AE003-902295-00 T-connector for profi les AH260-RG6395 outside on door sash profi les 2 pcs AE009-905150-00 AH900-TF649
T- connectors
Corner connectors
10
June 2012
RG60 Catalogue
Order No. Designation
AE011-903005-00 Glass support
AE011-903022-00 Central gasket corner
AE011-903325-00 Sealing element, at top, for double-leaf, inward and outward opening doors, access leaf acc. to DIN left
AE011-903327-00 Sealing element, at top, for double-leaf, inward and outward opening doors,access leaf acc. to DIN right
AE011-903330-00 Sealing element, at top, for double-leaf, inward and outward opening doors,access leaf acc. to DIN right
AE011-903332-00 Sealing element, at top, for double-leaf, inward and outward opening doors,access leaf acc. to DIN left
AE011-903345-00Sealing element for additional rebate sash profi le AH275-RG1260, top arrangement with rebate
sash acc. to DIN to the right, bottom arrangement with rebate sash acc. to DINto the left
AE011-903347-00 Sealing element for additional rebate sash profi le AH275-RG1260, bottom arrangment with rebate sash acc. to DIN to the right, top arrangement with rebate sash acc. to DIN to the left
AE005-000004-02 Plug for central adaptor straight AH275-RG1260
AE005-000007-02 Plug for central adaptor AH275-RG1261
Accessories
Order No. Designation
AE004-904015-00 Stroke gasket for window sash profi les
AE004-904035-00 Stroke gasket for doors
AE004-904285-00 Central gasket (highly insulated)
AE004-904003-20 Glazing gasket 6.5 mm, inside, with two sealing slips
AE004-90403-25 Glazing gasket 8,5 mm, inside, with two sealing slips
AE004-904003-30 Glazing gasket 4.0 mm, outside, with sealing slip
AE004-00004-00 Gasket for bottom rail
Gaskets
Order No. Designation
AE009-905140-00 Roll pin Ø4 mm x 8 mm (conical), for corner connector AE001-901440-00
AE009-905145-00 Roll pin Ø5 mm x 18 mm (cylindrical), for corner cnnector AE001-901499-00
AE009-905150-00 Roll pin Ø7 mm x 13.5 mm (cylindrical), for corner and T-connector
AE009-905160-00 Roll pin Ø7 mm x 18.0 mm (cylindrical), for corner and T-connector
AE009-000002-00 Sping pin Ø4mm x30mm, for bottom rail
Installation material
Inside Outside
Profi le Mobile Corner Connector Inside
Countersunk Screw DIN
963Measure X Mobile Corner
Connector OutsideCountersunk
Screw DIN 963 Measure X
Frame AH260-RG6121 AE001-901567-00 M5X20 12,15 AE001-901457-00 M5X12 10,35
Window Sash AH260-RG16211 AE001-901577-00 M5X20 12,15 AE001-901442-00 M4X8 5,2
Frame with T-Profi le AH260-RG6406 AE001-901-567-00 M5X20 12,15 AE001-901452-00 M5X12 8,55
Corner connectors for variable angles
11
www.balkan.gr
RG60 Catalogue
Cross section values (ideal inertia moments)
x Profi le Order No.
lx id [cm4]
Support width L [cm] {acc. to ifBT directive}
150 200 250 300 400 500 600
AH260-50600030 5,22 19,81 20,86 21,49 22,16 22,49 22,67
AH260-RG6121 17,68 19,36 20,27 20,80 21,37 21,65 21,80
AH260-RG6131 20,90 23,23 24,53 25,32 26,16 26,57 26,80
AH260-RG6211 26,17 28,48 29,74 30,49 31,28 31,66 31,87
AH260-RG6214 35,95 43,05 46,58 48,21 50,35 52,30 55,45
AH260-RG6215 35,95 43,05 46,58 48,21 50,35 52,30 55,45
AH260-RG6220 35,34 39,47 41,86 43,32 44,91 45,70 46,14
AH260-RG6222 47,35 54,23 62,78 65,39 70,12 72,73 73,50
AH260-RG6245 28,91 32,10 33,89 34,97 36,12 36,69 37,01
AH260-RG6260 24,41 28,15 30,36 31,74 33,25 34,00 34,43
AH260-RG6261 29,29 33,50 36,73 38,08 39,9 40,8 41,32
Statics
12
June 2012
RG60 Catalogue
Cross section values (ideal inertia moments)
x'x Profi le Order No.
lx id [cm4]
Support width L [cm] {acc. to ifBT directive}
150 200 250 300 400 500 600
AH260-RG6350 14,86 15,71 16,16 16,43 16,70 16,83 16,90
AH260-RG6406 20,27 22,47 23,69 24,42 25,20 25,58 25,79
AH260-RG6411 31,54 37,89 41,93 44,55 47,54 49,08 46,96
AH260-RG6526 48,52 77,46 111,00 114,50 118,35 120,28 121,36
AH260-RG6301 18,97 20,67 21,60 22,16 22,75 23,04 23,20
AH260-RG6311 22,80 24,83 25,97 26,64 27,37 27,72 27,92
AH260-RG6330 25,98 28,73 30,30 31,26 32,29 32,80 33,08
AH260-RG6335 23,81 26,43 27,93 28,84 29,83 30,32 30,59
AH260-RG6751 34,11 35,91 37,14 37,97 38,96 39,48 39,78
Statics
13
www.balkan.gr
RG60 Catalogue
Type of glazingUg
Single-pane glazing
Table 7 - Allocation of Ur values of individual profiles
to a Uf,BW design value for frames. DIN V 4108-4:2002-02
Uf - value for individual profiles
W / m²K
Uf,BW - design value
W / m²K
<0.90
<1.1
<1.3
<1.6
<2.0
<2.4
<2.8
<3.2
<3.6
<4.0
>4.0
>0.90
>1.0
>1.3
>1.6
>2.0
>2.4
>2.8
>3.2
>3.6
Uf value of framefrom BrokelmannTable 1-3acc. to DIN EN ISO 10077-2
e.g. 1.94 W/m²K
0.80
1.00
1.40
1.20
1.80
2.20
2.60
3.00
3.40
3.80
7.0
Table F0.1: Heat transfer coefficient Uw for windows with a frame surface portion of 30%
to the total surface area of the window. DIN EN ISO 10077-1:2000
5.7
UfW / m²K
Frame surface portion 30%
Two-paneinsulating glazing
3.3
3.1
2.9
2.7
2.5
2.3
2.1
1.9
1.7
1.5
1.3
1.1
4.3
1.0
2.7
2.6
2.4
2.3
2.2
2.1
1.9
1.8
1.6
1.5
1.4
1.2
4.4
1.4
2.8
2.7
2.4
2.5
2.3
2.2
2.0
1.9
1.8
1.6
1.5
1.3
4.5
1.8
2.9
2.8
2.7
2.5
2.4
2.3
2.22.0
1.9
1.6
1.5
1.7
2.2
4.6
3.1
2.9
2.8
2.6
2.6
2.4
2.32.1
2.0
1.9
1.6
1.7
2.6
4.8
3.1
3.2
3.0
2.8
2.7
2.6
2.4
2.3
2.0
2.2
1.9
1.7
3.0
4.9
3.4
3.2
3.1
2.9
2.8
2.7
2.6
2.4
2.32.1
2.0
1.9
2.1
2.0
2.4
2.3
2.7
2.5
3.4
5.0
3.5
3.3
3.2
3.1
3.0
2.8
2.1
2.2
2.4
2.5
2.7
2.8
3.1
2.9
3.3
3.2
3.5
3.6
3.8
5.1
7.0
6.1
3.1
2.9
3.3
3.2
3.5
3.6
3.8
3.9
4.0
4.1
4.3
4.4
Ug value of glazingfrom German Federal Gazette or the DIN 673 Standard
e.g. 1.1 W/m²K
Uw - value of windowe.g. 1.5W/m²K
Determination of nominal values of the heat transfer coeffi cient Uw from the tables of DIN EN ISO 10077-1: 2000
and DIN V 4108-4: 2000.
Determination of Uw values for windows and doors acc. to Example 1:
1. Taking of the nominal value Uf from the Brokelmann Table 1-3 acc. to DIN EN ISO 10077-2
2. Allocation of the Uf value and determination of Uf,BW in Table 7 acc. to DIN V 4108-4:2002-02
3. Transfer of the Uf,BW to Table F.1 or F.2 in order to determine the nominal value of the heat ransfer coeffi cient
Uw ( DIN 10077-1:2000 und DIN V 4108-4 )
4. Determination of the Ug value of the glazing and reading out the nominal value Uw in Table F.1 or F.2.
Attention: The nominal values Uw for windows and doors comprised in Tables F.1 and F.2 have been determined with
standard window sizes 1.23 m x 1.48 m and are taking a frame surface portion of 30% or 20% as a basis.
Example 1:
14
June 2012
RG60 Catalogue
Determination of nominal values of heat ransfer coeffi cient for windows and doors Uw for aluminium profi les.Table 7: Allocation of Uf values to UfBW - design values
Table 7- Allocation of the Uf values of individual profi lesto a Uf,BW design value for frames. DIN V 4108-4:2002-02
Table F.1: For a frame surface portion of 30%
Table F.1: Heat transfer coeffi cient Uw for windows with a frame surface portion of 30%to the total surface area of the window. DIN EN ISO 10077-1:2000
Uf - value forindividual profi les
W / m²K
Uf,BW - design valueW / m²K
<0.90 0.80
>0.90 <1.1 1.00
>1.0 <1.3 1.20
>1.3 <1.6 1.40
>1.6 <2.0 1.80
>2.0 <2.4 2.20
>2.4 <2.8 2.60
>2.8 <3.2 3.00
>3.2 <3.6 3.40
>3.6 <4.0 3.80
>4.0 7.0
Type of glazingUg W/m²K Uf W / m²K Frame surface portion 30%
1.0 1.4 1.8 2.2 2.6 3.0 3.4 3.8 7.0
Single-pane glazing 5.7 4.3 4.4 4.5 4.6 4.8 4.9 5.0 5.1 6.1
Two-paneinsulating glazing
3.3 2.7 2.8 2.9 3.1 3.2 3.4 3.5 3.6 4.4
3.1 2.6 2.7 2.8 2.9 3.1 3.2 3.3 3.5 4.3
2.9 2.4 2.5 2.7 2.8 3.0 3.1 3.2 3.3 4.1
2.7 2.3 2.4 2.5 2.6 2.8 2.9 3.1 3.2 4.0
2.5 2.2 2.3 2.4 2.6 2.7 2.8 3.0 3.1 3.9
2.3 2.1 2.2 2.3 2.4 2.6 2.7 2.8 2.9 3.8
2.1 1.9 2.0 2.2 2.3 2.4 2.6 2.7 2.8 3.6
1.9 1.8 1.9 2.0 2.1 2.3 2.4 2.5 2.7 3.5
1.7 1.6 1.8 1.9 2.0 2.2 2.3 2.4 2.5 3.3
1.5 1.5 1.6 1.7 1.9 2.0 2.1 2.3 2.4 3.2
1.3 1.4 1.5 1.6 1.7 1.9 2.0 2.1 2.2 3.1
1.1 1.2 1.3 1.5 1.6 1.7 1.9 2.0 2.1 2.9
Three-paneinsulating glazing
2.3 2.0 2.1 2.2 2.4 2.5 2.7 2.8 2.9 3.7
2.1 1.9 2.0 2.1 2.2 2.4 2.5 2.6 2.8 3.6
1.9 1.7 1.8 2.0 2.1 2.3 2.4 2.5 2.6 3.4
1.7 1.6 1.7 1.8 1.9 2.1 2.2 2.4 2.5 3.3
1.5 1.5 1.6 1.7 1.9 2.0 2.1 2.3 2.4 3.2
1.3 1.4 1.5 1.6 1.7 1.9 2.0 2.1 2.2 3.1
1.1 1.2 1.3 1.5 1.6 1.7 1.9 2.0 2.1 2.9
0.9 1.1 1.2 1.3 1.4 1.6 1.7 1.8 2.0 2.8
0.7 0.9 1.1 1.2 1.3 1.5 1.6 1.7 1.8 2.6
0.5 0.8 0.9 1.0 1.2 1.3 1.4 1.6 1.7 2.5
15
www.balkan.gr
RG60 Catalogue
Determination of the nominal values of the heat transfer coeffi cientfor windows and doors Uw for aluminium profi les
Table F.2:For a frame surface portion of 20%
Table F.2:Heat transfer coeffi cient Uw for windows with a frame surface protion of 20%to the total surface area of the window. DIN EN 19010077-1:2000
Note: The Tables F.1 and F.2 were calculated with Y-values from Annex E of DINEN ISO 10077-1:2000 for glazing spacers made of aluminium and steel (not of stainless type).
Type of glazingUg W/m²K Uf W / m²K Frame surface portion 30%
1.0 1.4 1.8 2.2 2.6 3.0 3.4 3.8 7.0
Single-pane glazing 5.7 4.8 4.8 4.9 5.0 5.1 5.2 5.2 5.3 5.9
Two-paneinsulating glazing
3.3 2.9 3.0 3.1 3.2 3.3 3.4 3.4 3.5 4.0
3.1 2.8 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.9
2.9 2.6 2.7 2.8 2.8 3.0 3.0 3.1 3.2 3.7
2.7 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.0 3.6
2.5 2.3 2.4 2.5 2.6 2.7 2.7 2.8 2.9 3.4
2.3 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.7 3.3
2.1 2.0 2.1 2.2 2.2 2.3 2.4 2.5 2.6 3.1
1.9 1.8 1.9 2.0 2.1 2.2 2.3 2.3 2.4 3.0
1.7 1.7 1.8 1.8 1.9 2.0 2.1 2.2 2.3 2.8
1.5 1.5 1.6 1.7 1.8 1.9 1.9 2.0 2.1 2.6
1.3 1.4 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.5
1.1 1.2 1.3 1.4 1.4 1.5 1.6 1.7 1.8 2.3
Three-paneinsulating glazing
2.3 2.1 2.2 2.3 2.4 2.5 2.6 2.6 2.7 3.2
2.1 2.0 2.0 2.1 2.2 2.3 2.4 2.5 2.6 3.1
1.9 1.8 1.9 2.0 2.0 2.2 2.2 2.3 2.4 2.9
1.7 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.2 2.8
1.5 1.5 1.6 1.7 1.8 1.9 1.9 2.0 2.1 2.6
1.3 1.4 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.5
1.1 1.2 1.3 1.4 1.4 1.5 1.6 1.7 1.8 2.3
0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.6 2.2
0.7 0.9 1.0 1.0 1.1 1.2 1.3 1.4 1.5 2.0
0.5 0.7 0.8 0.9 1.0 1.1 1.2 1.2 1.3 1.8
Table 1 - 3
16
June 2012
RG60 Catalogue
Nominal values of the heat transfer coeffi cient Uf
Fixed cross sections Moving cross sections
Outer Frame Outer Frame - Sash combination
External visible width External visible width
The nominal values of the heat transfer coeffi cient Uf given below have been determined according to EN ISO 10077-2 : vALUES IN W/m2K
Fixed cross sec-tionsOuter Frame
Moving cross sec-tionsOuter Frame - Sash combination AH260-RG6211
AE004-904935-00AH260-6220AE004-904935-00
AH260-RG6121
2.7 2.9 2.7
AH260-RG6131
2.5 2.8 2.6
AH260-RG6311 AH260-RG6335
17
www.balkan.gr
RG60 Catalogue
Nominal values of the heat transfer coeffi cient Uf
Fixed cross sections Moving cross sections
Outer Frame Outer Frame - Sash combination
External visible width External visible width
The nominal values of the heat transfer coeffi cient Uf given below have been determined according to EN ISO 10077-2 : vALUES IN W/m2K
Fixed cross sec-tionsOuter Frame
Moving cross sec-tionsOuter Frame - Sash combination AH260-RG6211
AE004-904935-00AH260-6220AE004-904935-00
AH260-RG6406
3.0 3.2 2.9
AH260-RG6411
2.8 3.1 2.8
18
June 2012
RG60 Catalogue
Nominal values of the heat transfer coeffi cient Uf
Moving cross sectionsOuter Frame - Sash combination
External visible width
The nominal values of the heat transfer coeffi cient Uf given below have been determined according to EN ISO 10077-2 : vALUES IN W/m2K
Moving cross sec-tionsOuter Frame - Sash combination AH260-RG6211
AE004-904935-00AH260-6220AE004-904935-00
AH260-RG6406
3.1 2.8
AH260-RG6411
3.0 2.7
19
www.balkan.gr
RG60 Catalogue
AH260-RG6121Frame profi le Dev. anod.: 402/324* mm W=1,446 kg/m
Dev. mech.: 92 mm
* Development for the connected profi le
34
60,2
58
4,5
24
55,7
AE001-901569-00
AE003-902046-00
AE003-902026-00
AE001-901459-00
AH260-5060030Frame profi le for facade Dev. anod.: 434/305* mm W=1,624 kg/m
Dev. mech.: 86 mm
30
49,5
56
72,5
4,5
60
28
24
55,5
AE001-901459-00
AE001-901569-00
20
June 2012
RG60 Catalogue
AH260-RG6211Sash profi le Dev. anod.: 436/380* mm W=1,464 kg/m
Dev. mech.: 90 mm
* Development for the connected profi le
In order to achieve the Uf value for specifi c conditions
see Diagram Uf Values
51
4,3
4,5
3936
24
75
65,5
70
AE001-901440-00
AE001-901579-00
44
60,2
68
4,5
14
55,7
AE001-901589-00
AE001-901474-00
AE003-902047-00
AE003-902033-00
AH260-RG6131Frame profi le Dev. anod.: 437/339* mm W=1,640 kg/m
Dev. mech.:112mm
21
www.balkan.gr
RG60 Catalogue
* Development for the connected profi le
AH260-RG6220Sash profi le Dev. anod.: 542/426* mm
W=2,094 kg/m
Dev. mech.: 142 mm
77 24
4,565
70
4,3
101
36
65,5
AE001-901484-00
AE001-901684-00
AH260-RG6214Sash profi le, round Dev. anod.: 449/393* mm W=1,589kg/m
Dev. mech.: 90 mm
12,1
3936
4,3
70
51 24
57,9
AE001-901440-00
AE001-901579-00
22
June 2012
RG60 Catalogue
AH260-RG6215Sash profi le perimetrical locking Dev. anod.: 398 mm W=1,761 kg/m Dev. mech.: 100 mm
4,3
70
56 24
4,536 44
65,5
AE001-901545-00
AE001-901540-00
AH260-RG6222Sash profi le perimetricallocking
Dev. anod.: 432 mm W=2,228kg/m
Dev. mech.: 142 mm
4,3
70
77 24
4,56536
65,5
AE001-901484-00
AE001-901550-00
23
www.balkan.gr
RG60 Catalogue
AH260-RG6245Transom for sash Dev. anod.: 469/391* mm W=1,744 kg/m
Dev. mech.: 116 mm
824,
5
70
3424 24
65,5
AE003-902025-00
AE003-902046-00
AH260-RG6260Rebate profi le Dev. anod.: 430/354* mm W=1,358 kg/m
Dev. mech.: 66 mm
Sealing element AE011-903345-00
for rebate sash acc. to DIN at right = top
for rebate sash acc. to DIN at left = bottom
Sealing element AE011-903347-00
for rebate sash acc. to DIN at right = bottom
for rebate sash acc. to DIN at left = top66
72
4,7
68
34
60
4,5
* Development for the connected profi le
24
June 2012
RG60 Catalogue
* Development for the connected profi le
AH260-RG6406Transom / Mullion Dev. anod.: 449/371* mm W=1,657 kg/m Dev. mech.: 116 mm
AH260-RG6261Transom / MullionPerimetrical Mechanism Dev. anod.: 433/359* mm W=1,641kg/m Dev. mech.: 66 mm
82
4,5
60
3424 24
55,5
AE001-901450-00
AE001-901569-00
AE003-902046-00
AE003-902025-00
66
72
4,5
60,6
29,8
4,7
68,3
25
www.balkan.gr
RG60 Catalogue
AH260-RG6411Transom / Mullion Dev. anod.: 489/391* mm W=1,827g/m Dev. mech.: 136 mm
92 4,5
55,5
60
24 44 24
AE003-902047-00
AE003-902028-00
AE001-901589-00
AE001-901469-00
AH260-RG6526Transom for sash Dev. anod.: 589/491* mm W=2,839kg/m Dev. mech.: 236 mm
* Development for the connected profi le
44 2424
20 52 20
55,5
50
4,5
6050
AE003-902047-00
AE003-902028-00
R
26
June 2012
RG60 Catalogue
AH260-RG6311Door frame profi le Dev. anod.: 460/334* mm W=1,771 kg/m Dev. mech.:114 mm
Outward opening
70
7,5
44 10
4,3
60
55,7
16
AE001-901003-25
AE001-901654-00
AH260-RG6301Door frame profi le Dev. anod.: 465/339* mm W=1,773 kg/m Dev. mech.: 114 mm
Inward opening
44 16
7,5
70
4,3
60
10
55,7
AE001-901375-00
AE001-901654-00
27
www.balkan.gr
RG60 Catalogue
* Development for the connected profi le
AH260-RG6335Door sash profi le
Dev. anod.:526/390* mm W=1,968 kg/m Dev. mech.:146 mm
Outward opening
10 48 24
4,598
16
7,5
60 55,5
AE001-901003-30
AE001-901679-00
AH260-RG6330Door sash profi le
Dev. anod.:522/388* mm W=1,996kg/m Dev. mech.:146 mm
Inward opening
74 24
7216
7,5
60
4,3
10
4,5
55,5
AE001-901375-00
AE001-901679-00
28
June 2012
RG60 Catalogue
AH260-RG6751Corner post profi le Dev. anod.: 607/365* mm W=2,500kg/m Dev. mech.: 160 mm
65
65
605
60 5
AE003-902056-00
AE003-902030-00
AH260-RG6350Change profi le for door frame Dev. anod.: 345/255* mm W=1,276kg/m Dev. mech.: 50 mm
36,5
50
58
52,5
17,2
4,3
53,7
* Development for the connected profi le
29
www.balkan.gr
RG60 Catalogue
109
133
60
4,5 55,5
24
AE
003-902295-00
AE
003-902050-00
AH260-RG6395Base profi le Dev. anod.: 661/478* mm W=2,781 kg/m Dev. mech.: 242mm
AH900-TF403BStop ledge Dev. anod.: 101 mm W=0.198 kg/m Dev. mech.: 14,5 mm
14,5
24,5
4,5
4,5
30
June 2012
RG60 Catalogue
AH900-TF403Stop ledge Dev. anod.: 96 mm W=0.184 kg/m Dev. mech.: 14 mm4
4,5
14,5
23
AL900-911Connecting Rod Dev. anod.: 46 mm W=0.124 kg/m Dev. mech.: 14 mm
AH900-370Connecting Rod Dev. anod.: 132,2 mm W=0.316 kg/m Dev. mech.: 20 mm
AH900-TF290Connecting rod Dev. anod.: 50 mm W=0.161 kg/m Dev. mech.: 13,5 mm
13,5
2,5
2,5
19,5
Opening of connecting rod channels, cutting to length and perforation of the connecting rod for the FWB window fi tting
AH900-TF269Additional profi le Dev. anod.: 151 mm W=0,323 kg/m Dev. mech.: 47 mm34,5
5,8
AH900-TF292Weather rail Dev. anod.: 67 mm W=0.122 kg/m Dev. mech.: 22 mm
B 4,2x16
18
12
AH900-TF368Connecting profi le Dev. anod.: 47 mm W=0.093 kg/m Dev. mech.: - mm
7,5
5
7,5
14
19
1,8
419
20
5
3,9 20,7
39,8 AH900-TF553
Dev. anod.: 94 mm W=0.446 kg/m
31
www.balkan.gr
RG60 CatalogueScale: 1:2
AH900-TF481Corner connector profi leW=1,843 kg/m
AH900-TF483Corner connector profi leW=2,881 kg/m
50
6
65
50
65
12
AH900-TF495Corner connector profi leW=2.285kg/m
50
65
16,4
AH900-TF496Corner connector profi leW=2,422 kg/m
65
50
20
AH900-TF497Corner connector profi leW=2,405 kg/m
50
65
22,8
AH900-TF498Corner connector profi leW=2,673 kg/m
50
26,4
66,4
65
32
June 2012
RG60 Catalogue
AH900-TF499Corner connector profi leW=2,782 kg/m
50
70
30
65
Scale: 1:2
AH900-TF500Corner connector profi leW=2,751 kg/m
AH900-TF501Corner connector profi leW=2,930 kg/m
AH900-TF502Corner connector profi leW=3.503 kg/m
AH900-TF558Corner connector profi leW=2.459 kg/m
50
65
66,4
32
34
50
65
74
45,4
5065
85,4
50
20,5
65
33
www.balkan.gr
RG60 Catalogue
AE001-901442-00Corner Connector for Variable Angle
AE001-901452-00Corner Connector for Variable Angle
AE001-901457-00Corner Connector for Variable Angle
25°-180°
6
612
,1
12,1
25°-180°
16,5
16,5
25°-180°
34
June 2012
RG60 Catalogue
20,1
20,1
25°-180°
20.120
.1
Scale: 1:2
AE001-901567-00Corner Connector for Variable Angle
AE001-901577-00Corner Connector for Variable Angle
35
www.balkan.gr
RG60 Catalogue
AH900-TF649T-connector profi leW=0.813 kg/m
AH900-TF650T-connector profi leW=0.911 kg/m
50,1
11,5
46,5
13
19,4
AH900-TF547T-connector profi leW=0.623kg/m
50,1
11,5
36
June 2012
RG60 Catalogue
AH900-TF460Glazing bead Dev. anod.: 168 mm W=0,281 kg/m Dev. mech.: 66 mm
44
22
AH900-TF457AGlazing bead Dev. anod.: 147 mm W=0,335 kg/m Dev. mech.: 57 mm
Glazing beads for bent elements. Prior to bending cut off ele-ments according to the respective glazing thickness.
for 10 mm receiving groove
for 10 mm receiving groove
34
22
21
22
AH900-TF454Glazing bead Dev. anod.: 121mm W=0,276 kg/m Dev. mech.:43 mm
32
22
AH900-TF457Glazing bead Dev. anod.: 143mm W=0,326kg/m Dev. mech.:54 mm
37
www.balkan.gr
RG60 Catalogue
AH900-TF463Glazing bead Dev. anod.: 152,1 mm W=0,253 kg/m Dev. mech.: 39 mm
AH900-TF465Glazing bead Dev. anod.: 212 mm W=0.363 kg/m Dev. mech.: 59 mm
AH900-TF466Glazing bead Dev. anod.: 232 mm W=0,400 kg/m Dev. mech.: 69 mm
37
22
47
22
for 10 mm receiving groove
for 10 mm receiving groove
for 10 mm receiving groove
27
22
AH900-TF464Glazing bead Dev. anod.: 193 mm W=0,325 kg/m Dev. mech.: 49 mm
for 10 mm receiving groove
1722
38
June 2012
RG60 Catalogue
18
7
8
4
10,8
5
4
60
7
17,3
5
60
Roll Pin AE009-905160-00
Taper Pin AE009-905140-00
Profi le
connector for inner shellMeasure bMeasure h
AH260-RG6121 AH900-TF 496 20,0 AE001-901569-00 AE009-905160-00AH260-RG6131 AH900-TF 499 20,0 AE001-901589-00 AE009-905160-00
Profi le
connector for inner shellMeasure bMeasure h
AH260-RG6211 AH900-TF 496 30,6 AE001-901579-00 AE009-905160-00AH260-RG6220 AH900-TF 502 30,6 AE001-901684-00 AE009-905160-00
Window Frame
Profi le
connector for inner shellMeasure bMeasure h
AH260-RG6121 AH900-TF 495 12,0 AE001-901459-00 AE009-905150-00AH260-RG6131 AH900-TF 498 12,0 AE001-901474-00 AE009-905150-00
Profi le
connector for inner shellMeasure bMeasure h
AH260-RG6121 AH900-TF 481 7,5 AE001-901440-00 AE009-905140-00AH260-RG6131 AH900-TF 500 7,5 AE001-901484-00 AE009-905140-00
7
13,5
18
7
8,5
60
7
7
608,
5
Roll Pin AE009-905160-00
Taper Pin AE009-905140-00
Window Sash
39
www.balkan.gr
RG60 Catalogue
Profi le
connector for inner shellMeasure bMeasure h
AH260-RG6406 AH900-TF 496 20,0 AE001-901569-00 AE009-905160-00
AH260-RG6411 AH900-TF 499 20,0 AE001-901589-00 AE009-905150-00
Profi le
connector for inner shellMeasure bMeasure h
AH260-RG6406 AH900-TF 483 12,0 AE001-901450-00 AE009-905150-00
AH260-RG6411 AH900-TF 497 12,0 AE001-901469-00 AE009-905150-00
8,5
607
7
7
7
8,5
60
Roll Pin AE009-905160-00AE009-905150-00
Roll Pin AE009-905150-00
Profi le
connector for inner shellMeasure bMeasure h
AH260-RG6406 AE003-902046-00 AE009-905160-00 AE003-902025-00 AH900-TF547 12,0 AE003-902001-51 AE009-905150-00
AH260-RG6411 AE003-902047-00 AE009-905160-00 AE003-902028-00 AH900-TF547 22,8 AE003-902001-53 AE009-905150-00
AH260-RG6526 AE003-902047-00 AE009-905150-00 AE003-902028-00 AH900-TF547
60
36
4,5
8,5
36
24
8,5
7
7
Roll Pin AE009-905150-00
Roll Pin AE009-905150-00
40
June 2012
RG60 Catalogue
W1
8.5
X
X
8.5
tan W1
x Layout (marking) measure A = 43,8mm +
Moving corner connector
Countersunk screw M 5x12 mm DIN 963
5.5
Countersunk screwM 5x12 mm DIN 963
Layout
(marking)
measure A
90° countersunk
5.5
* for AH260- RG6211B (outside)Bore hole 4.4 mm Diam.with countersunk screw M 4x8 mm DIN 963
X = half of chamber height + wall thickness (90° measured)
90° countersunk
Layout
(marking)
measure A
Profi le MeasureX
MeasureX
AH260-RG6121 AE001-901567-00 906422 12.15 AE001-901457-00 906418 10.35
AH260-RG6131 AE001-901587-00 906422 17.20 AE001-901472-00 906422 15.40
Profi le MeasureX
MeasureX
AH260-RG6211 AE001-901577-00 906422 12.15 AE001-901577-00 906401 5.2
Window frame inside
inside
outside
Window sash outside
Profi le MeasureX
MeasureX
AH260-RG6406 AE001-901567-00 906422 12.15 AE001-901452-00 906418 8.55
AH260-RG6411 AE001-901587-00 906422 17.20 AE001-901467-00 906422 13.95
Transom to Frame inside outside
41
www.balkan.gr
RG60 Catalogue
maximum 15°
=> 500
15°
75°
AH260-RG6121 AH260-RG6211 AH260-RG6211 AH260-RG6121
42
June 2012
RG60 Catalogue
18
7
8,5
60
7
Roll Pin AE009-905160-00
7
18
Roll Pin AE009-905160-00
60
20,8
7
Profi le
AH260-RG6330 AH900-TF502 22,7 AE001-901003-15 AE009-905160-00 AH900-TF501 6.1 AE001-901375-00AH260-RG6335 AH900-TF502 22,7 AE001-901003-15 AE009-905160-00 AH900-TF501 6.1 AE001-901003-30
43
www.balkan.gr
RG60 Catalogue
Roll Pin AE009-905150-00
Roll Pin AE009-905150-00
36
7
8,5
7
24
36 4,5
8,5
607
36
4,5
8,5
Profi le
AH260-RG6121 AE003-902-046-00 AE009-905150-00 AE003-902026-00 AE009-905150-00AH260-RG6131 AE003-902047-00 AE009-905150-00 AE003-902029-00 AH900-TF547 26.04 90200152 AE009-905150-00AH260-RG6395 AE003-902050-00 2xAE009-905160-00 AE002-902033-00 AH900-TF547 68.9 90200115 2xAE009-905160-00
44
June 2012
RG60 Catalogue
Profi leinner shell outer shell
T- connector Roll Pin T- connector Roll Pin
AH260RG6245 AE003-902046-00 AE009-905160-00 AE003-902025-00 AE009-905150-00
7
8,5 53
7
8,5
70
Roll Pin AE009-905150-00
Roll Pin AE009-905150-00
70
8,58,5
4,5
7
36
24
7
36
Sash ProfilesAH260-RG6211AH260-RG6220
45
www.balkan.gr
RG60 Catalogue
Accessories
AE011-903325-00 Sealing element at top on 2-sash doors, with doorsash profi les AH275-RG2330 andAH275-RG2335Access sash acc.to DIN left
AE011-903330-00 Sealing element at top on 2-sash doors, with door sash profi les AH275-RG2330 andAH275-RG2335Access sash acc.to DIN left
AE011-903001-00Glass Support
AE011-903000-19 Central Gasket Corner
AE011-903327-00 Sealing element at top on 2-sash doors, with door sash profi les AH275-RG2330 andAH275-RG2335Access sash acc.to DIN left
AE011-903332-00Sealing element at top on 2-sash doors, with door sash profi les AH275-RG2330 andAH275-RG2335Access sash acc.to DIN left
39,4
11,7
46
June 2012
RG60 Catalogue
AE011-903009-00 Threshold Stopper
AE011-903010-00 Threshold Stopper
AE011-903011-00 Threshold Stopper
AE011-903012-00 Threshold Stopper
AE011-903013-00 Sealing Piece
AE011-903014-00 Sealing Piece
AE011-903015-00 Sealing Piece
AE011-903016-00 Sealing Piece
AE009-905140-00Roll pin for corner connectors AE001-901440-00
AE009-905145-00Roll pin for corner connectors AE001-901499-00
AE009-905150-00Roll pin for cornerand T-connectors
AE009-905160-00Roll pin for cornerand T-connectors
AA331-012-02-01Brushes No 12mm
8
4
7
18
5
18
13,5
7
12
47
www.balkan.gr
RG60 Catalogue
AE004-904015-00 Stroke gasket for window sash profi le EPDM, black
3
AE004-904035-00 Stroke gasket for doors profi le EPDM, black
4
AE004-904405-00Glazing gasket outside, 4.0 mm EPDM, black
4
4
AE004-904495-00Glazing gasket inside, 6.5 mm EPDM, black
5,5-7,5
AE004-904505-00Glazing gasket inside, 8.5mm EPDM, black
7,5-9,5
5,5-7,5
27,5
AE004-904002-80 Glazing gasket inside, 6.5 mm EPDM, black
AE004-904002-85Glazing gasket inside, 8.5 mm EPDM, black
7,5-9,5
27,4
AE004-904935-00 Central gasket corner mould-ing 50x50mm EPDM, black
5
16,3
AE004-904870-00
36,3
AE013-929270-00 Adapter for AH900-TF269, PVC black
23,4
5,5-7,527
,5
AE004-904003-20Glazing gasket inside, 6.5 mm EPDM, black
AE004-904003-25Glazing gasket inside, 8.5 mm EPDM, black
27,5
7,5-9,5
48
June 2012
RG60 Catalogue
9
7
8 2
5
53
5
11
3
2
2
Fixed
FixedFixed Fixed Fixed
Fixed Fixed Fixed
Fixed Fixed
5
6
4
5
1
3
1
2
2
4 8 2
325
6 63
51
2 5
7 4
65
5
56
9
4 5
65
78
32
2
65
1
32
7 8
4
65
5
5
3
5+1 26
5
3
2
1
4
2+4
2
4
6
5+4
5
6
5
5 5
5+4
5
5
6
6
4
4
5
Fixed
6
4
SECTIONS OVERVIEW
Views From Outside Sash
Sash SashSash
SashSashSash
Sash
Sash
Sash
Sash
Sash
Sash
Sash
Sash
Sash
10
65
5
56
4
Rebate Sash
5
1
37
4 5
2
Fixed
Sash
49
www.balkan.gr
RG60 Catalogue
Section numbers inside brackets aredoor sashes with bottom double seals.
46 (48)
(48)4646 (48)
(48)4646 (48)
(48)46(48)46(48)46
(48)46(48)46(48)46(48)46
46 (48)
(48)46(48)46(48)46(48)46(48)46
(48)46(48)4646 (48)
1143
Optionallyused sash
FlügelFlügel
SashSash
SashSashSashSash
SashSash
Sash
SashSashSash
38 3947
3935 3442
34
4333 2
47 2
5047
2
42
34
341
32
3231 44 4531 32
32
32
31 32 3433
36
3635
43 41
38 39
39
33 34
43 36
47
33
39
39381 2
2
33
47
243 42 341
2
47
21
1 2
2
33 344544 3433
2
21 38 39
39
33 3444 45 3433
39
3938
Fixed
Fixed Fixed
Fixed
Fixed Fixed
Fixed Fixed Fixed
Fixed Fixed
3232
4311 41 40 40 41
43 43 41 41
SECTIONS OVERVIEW
Door sash inward opening
Views From Outside
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Active sash
Active sash
Active sash
Active sash
Active sash
Active sash
50
June 2012
RG60 Catalogue
Section numbers inside brackets are door sashes with bottom double seals.
46 (65)46 (65)
(65)46(65)46
(65)4646 (65)46 (65)
(65)46
46 (65)
(65)4646 (65)
(65)46(65)46(65)46
46 (65)
(65)4646 (65)
52 52
FixedFixed
5251
52
52
5251 444551 52
52
1 52
52
62
247
50
247
251 63
52
Sash
Sash Sash
Views From Outside
Door sash outward opening
SECTIONS OVERVIEW
61616363
2
1
6161
39
39
38
54 535453
63
54
2
53
617
2
FixedFixed
FixedFixed
761
Fixed
FixedFixed
Fixed
Fixed
63
4445
39
39381 2
2
53 5445 44
21
2
4711
263
546263
47
53
1 38 39
39
53
47
263
5453
39
3938
6163
1 2
2
53 54
62 541
39
47
3938
Sash Sash
Sash
Sash Sash Sash Sash
Sash Sash
Sash Sash
1163
1 2
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Active sash
Active sash
Active sash
Active sash
Active sash
Active sash
51
www.balkan.gr
RG60 Catalogue
Section numbers inside brackets are door sashes with bottom double seals.
46 (65)46 (65)
(65)46(65)46
(65)4646 (65)46 (65)
(65)46
46 (65)
(65)4646 (65)
(65)46(65)46(65)46
46 (65)
(65)4646 (65)
52 52
FixedFixed
5251
52
52
5251 444551 52
52
1 52
52
62
247
50
247
251 63
52
Sash
Sash Sash
Views From Outside
Door sash outward opening
SECTIONS OVERVIEW
61616363
2
16161
39
39
38
54 535453
63
54
2
53
617
2
FixedFixed
FixedFixed
761
Fixed
FixedFixed
Fixed
Fixed
63
4445
39
39381 2
2
53 5445 44
21
2
4711
263
546263
47
53
1 38 39
39
53
47
263
5453
39
3938
6163
1 2
2
53 54
62 54139
473938
Sash Sash
Sash
Sash Sash Sash Sash
Sash Sash
Sash Sash
1163
1 2
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Optionallyused sash
Active sash
Active sash
Active sash
Active sash
Active sash
Active sash
52
June 2012
RG60 Catalogue
34
7
58
34
7
58
44
7
68
44
7
68
Frame dimension=
Rebate dimension=
Glazing dimension=
Frame dimension=
Rebate dimension=
Glazing dimension=
AH260-RG6121
AE004-904405-00 AE004-904405-00
AH260-RG6121
AH260-RG6131 AH260-RG6131
AE004-904405-00 AE004-904405-00
53
www.balkan.gr
RG60 Catalogue
51
7
Sash dimension=
Rebate dimension=
Glazing dimension=
28
58 6 39
Frame dimension=
51
7
28
58639
AH260-RG6121
AH260-RG6121
AH260-RG6211
AH260-RG6211AE004-904015-00
AE004-904015-00
AE004-904935-00
AE004-904935-00
AE004-904405-00
AE004-904405-00
54
June 2012
RG60 Catalogue
7738
68 6 65
7540
68665
7
AH260-RG6220
AE004-904015-00
AE004-904935-00
AE004-904405-00
AH260-RG6131
AH260-RG6220
AH260-RG6131
AE004-904405-00
AE004-904015-00
AE004-904935-00
Sash dimension=
Rebate dimension=
Glazing dimension=
Frame dimension=
7
55
www.balkan.gr
RG60 Catalogue
AE004-904015-00
7
56
28
Rebate dimension=
Glazing dimension=
Sash dimension=
Frame dimension=
AE004-904935-00
AH260-RG6215
AH260-RG6121
AE004-904405-0058 6 44
AE004-904015-00
AE004-904935-00
7 Glazing dimension=
AE004-904405-00
77
38
68 6 65
AH260-RG6131
AH260-RG6222
Rebate dimension=
Sash dimension=
Frame dimension=
56
June 2012
RG60 Catalogue
51
7
Sash dimension=
Rebate dimension=
Glazing dimension=
38
92 6 39
Frame dimension=
7 1622
51
7 Glazing dimension=
38
92639
716 22Rebate dimension=
Frame dimension=
Sash dimension=
AH260-RG6411
AH260-RG6211
AE004-904935-00
AE004-904015-00
AE004-904405-00
AE004-904405-00
AE004-904935-00
AE004-904015-00
AH260-RG6211
AH260-RG6411
57
www.balkan.gr
RG60 Catalogue
51
7
Sas
h di
men
sion
=
Reb
ate
dim
ensi
on=
Gla
zing
dim
ensi
on=
926
39
Fram
e di
men
sion
=
7
51
32
639
AE004-904405-00
AH260-RG6211
AE004-904935-00
AH260-RG6411
AH260-RG6211
AE004-904015-00
58
June 2012
RG60 Catalogue
51
7
Sas
h di
men
sion
=
Reb
ate
dim
ensi
on=
Gla
zing
dim
ensi
on=
639
Fram
e di
men
sion
=
7
51
32
639
AH260-RG6211
AE004-904405-00
AE004-904935-00
AE004-904015-00
AH260-RG6260
AH260-RG6211
66
59
www.balkan.gr
RG60 Catalogue
Rebate dimension=34
Glazing dimension=77
AE004-904405-00
AH260-RG6406
7
AE004-904405-00
34
7 AH260-RG6245
Rebate dimension=
Glazing dimension=
60
June 2012
RG60 Catalogue
Glazing dimension=7
72670
644 74 Rebate dimension=
Sash dimension=
AH260-RG6330
AE
004-904405-00
AH260-RG6301AE004-904035-00
50Frame dimension=
7
72 6 70
6 4474
AH260-RG6330
AE004-904405-00
AH260-RG6301AE004-904035-00
50
Glazing dimension=
Rebate dimension=
Sash dimension=
Frame dimension=
61
www.balkan.gr
RG60 Catalogue
Glazing dimension=7
72668
444 74 Rebate dimension=
Sash dimension=
AH260-RG6330
AE
004-904405-00
AH260-RG6331AE004-904035-00
48Frame dimension=
Glazing dimension=
Rebate dimension=
Sash dimension=
Frame dimension=
7
72 6 68
4 4474
AH260-RG6330
AE
004-904405-00
AH260-RG6331AE004-904035-00
48
AH900-TF269
AH900-TF269
62
June 2012
RG60 Catalogue
51
7
38
68639
Glazing dimension=
Rebate dimension=
Sash dimension=
Frame dimension=
AH260-RG6211
AE
004-
9044
05-0
0
AE
004-
9049
35-0
0
AH260-RG6131
AE
04-9
0401
5-00
51
7
38
68 6 39
Glazing dimension=
Rebate dimension=
Sash dimension=
Frame dimension=
AH260-RG6211
AE
004-
9044
05-0
0
AE004-904935-00
AH260-RG6131
AE
04-9
0401
5-00
63
www.balkan.gr
RG60 Catalogue
AH
260-
RG
6211
AE
004-
9040
15-0
0
AE004-904405-00
AE004-904405-00
AE
004-
9049
35-0
0
AH
260-
RG
6411
77
3992
5138
6
Gla
zing
dim
ensi
on=
Reb
ate
dim
ensi
on=
Sas
h di
men
sion
=
Fram
e di
men
sion
=
64
June 2012
RG60 Catalogue
3992
Glazzing dimension =
51
Rebate dimension =
Sash dimension =
38
Frame dimension =6
672
74
4
AH
260-
RG
6211
AE
004-
9040
15-0
0
AE004-904405-00
AE004-904935-00
AH
260-
RG
6411
AH900-TF269AE013-929270-00
AE
004-
9040
35-0
0
AE004-904405-00
AH
260-
RG
6330
7
7
65
www.balkan.gr
RG60 Catalogue
9244
672
74
4
Gla
zing
dim
ensi
on =
Reb
ate
dim
ensi
on =
Sas
h di
men
sion
=
AE
004-
9049
35-0
0
AH
260-
RG
6411
AH900-TF269AE013-929270-00
AE
004-
9040
35-0
0AE004-904405-00
AH
260-
RG
6330
AE004-904405-00
77
66
June 2012
RG60 Catalogue
9244
672
744
Gla
zing
dim
ensi
on =
Reb
ate
dim
ensi
on =
AE
004-
9049
35-0
0
AH
260-
RG
6411
AH900-TF269AE013-929270-00
AE
004-
9040
35-0
0
AE004-904405-00
AH
260-
RG
6330
AE004-904405-00
77
67
www.balkan.gr
RG60 Catalogue
7G
lazi
ng d
imen
sion
=7
72
6
9810
10
6
4874
Reb
ate
dim
ensi
on=
Sas
h di
men
sion
=
AH
260-
RG
6330
AE004-904405-00
AH
260-
RG
6335
AE
004-
9040
35-0
0
68
June 2012
RG60 Catalogue
7G
lazi
ng d
imen
sion
=7
72
6
9810
10
6
4874
Reb
ate
dim
ensi
on=
Sas
h di
men
sion
=
AH
260-
RG
6330
AE004-904405-00
AH
260-
RG
6335
AE
004-
9040
35-0
0
69
www.balkan.gr
RG60 Catalogue
4492
3482
AE004-904405-00
AE004-904405-00
AH
260-
RG
6406
AH
260-
RG
6411
77
77
70
June 2012
RG60 Catalogue
48 Rebate dimension =70 6Sash dimension =76Frame dimension =
Glazing dimension =
9864450 Sash dimension =
47,5 69,5776,5
98 6 4450
AE004-904035-00
AE004-904035-00
AE004-904405-00
AE004-904035-00
AE004-904035-00
AE004-904405-00
AH260-RG6311 AH260-RG6335
AH260-RG6335 AH260-RG6311
7
7
71
www.balkan.gr
RG60 Catalogue
44 7
48694100 Sash dimension =
Rebate dimension =
Glazing dimension =
Frame dimension =
98668
74 Sash dimension =
44
48
7
48 94100
98 6 68
74
AE004-904035-00
AE004-904035-00
AH260-RG6335
AE004-904405-00
AH260-RG6350AH260-RG6131
AE004-904035-00
AE004-904035-00
AH260-RG6335
AE004-904405-00
AH260-RG6350 AH260-RG6131
50
6
72
June 2012
RG60 Catalogue
51
7
Sas
h di
men
sion
=
Reb
ate
dim
ensi
on=
Gla
zing
dim
ensi
on=
88
926
39
Fram
e di
men
sion
=
1622
7
98
648
6 50
AH260-RG6211
AE004-904405-00
AH260-RG6411
AH260-RG6335
AH
275-RG
6350
AE004-904035-00
AE004-904935-00
73
www.balkan.gr
RG60 Catalogue
Sas
h di
men
sion
=
Reb
ate
dim
ensi
on=
Gla
zing
dim
ensi
on=
Fram
e di
men
sion
=
7
98
6
48
650
92
7
44
AH
260-
RG
6350
AE004-904405-00
AH260-RG6411
AH260-RG6335
AE004-904035-00
74
June 2012
RG60 Catalogue
6 39
POST
CENTER LINE
25 103,5
30,5
246,5
1211
50 105,5
4,556
101
2251
13
Section Insert frame RG60 Series for facade
AH260-5060030
AH260-RG6211
AE004-904495-00
AE004-904015-00
AE004-904405-00
AE004-904935-00
75
www.balkan.gr
RG60 Catalogue
672
PO
ST
CE
NTE
R L
INE
136,
5
306,
5
1211
5013
8,5
4,5
5613
4
AH
260-
5060
030
9002
2158
7
74
964
2422
AH
260-
RG
6330
AH900-TF269 PK270
AE004-904495-00
AE004-904035-00
AE004-904405-00
76
June 2012
RG60 Catalogue
6
PO
ST
CE
NTE
R L
INE
6,5
1211
5016
4,5
4,5
56
AH
260-
RG
6335
7
60
2248
5030
806
70
156
162,
5
98
AH
260-
RG
6350
AH
260-
5060
030
9002
2164
AE004-904405-00
AE004-904035-00
AE004-904495-00
77
www.balkan.gr
RG60 Catalogue
Turn, Turn and Tilt Window
Profiles Pcs Dimension Cutting
AH260-RG6121 2 L 45° - 45°Window frame (horizontal)
AH260-RG6121 2 H 45° - 45°Window frame (vertical)
AH260-RG6211 2 L-56 45° - 45°Window sash (horizontal) ( = SW)
AH260-RG6211 2 H-56 45° - 45°Window sash (vertical) ( = SH)
GB1 SW-102 90° - 90°Glazing bead horizontal 2
GB2 SH-146 90° - 90°Glazing bead vertical 2
Gaskets Dimension
AE004-904015-00 2L+2HStroke gasket inside
AE004-904935-00 2L+2HCentral gasket
AE004-904002-80 2L+2HGlazing gasket inside
Glass Length
Glass SW-116For sash
Pcs Height
1 SH-116
AE004-904405-00 2L+2HGlazing gasket outside
Optional Pcs.
AE011-903000-19 4Vulcanized corner joints
Same dimensions for AH260-RG6214
H
LL
H
AH
260-
RG
6121
AH
260-
RG
6211
AE
004-
9040
15-0
0
AE
004-
9049
35-0
0A
E00
4-90
4405
-00
AE
004-
9040
02-8
0
GB 1
SW H
AH260-RG6121
AH260-RG6211AE004-904015-00
AE004-904935-00 AE004-904405-00
AE004-904002-80
GB
2
L
SW
78
June 2012
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6131 2 L 45° - 45°Window frame (horizontal)
AH260-RG6131 2 H 45° - 45°Window frame (vertical)
AH260-RG6220 2 L-76 45° - 45°Window sash (horizontal) ( = SW)
AH260-RG6220 2 H-76 45° - 45°Window sash (vertical) ( = SH)
GB1 SW-154 90° - 90°Glazing bead horizontal 2
GB2 SH-198 90° - 90°Glazing bead vertical 2
Gaskets Dimension
AE004-904015-00 2L+2HStroke gasket inside
AE004-904935-00 2L+2HCentral gasket
AE004-904002-80 2L+2HGlazing gasket inside
Glass Length
Glass SW-168For sash
Pcs Height
1 SH-168
AE004-904405-00 2L+2HGlazing gasket outside
Optionally Pcs.
AE011-903000-19 4Vulcanized corner joints
Same dimensions for AH260-RG6222
LHH
L
Turn, Turn and Tilt Window
AH260-RG6220
AH260-RG6131
AH260-RG6220 AΕ004-90415-00
AH260-RG6131GB2
AE004-904002-80
L
SW
AE004-904405-00 AE004-904935-00AE004-904405-00AE004-904935-00
AE004-904015-00
79
www.balkan.gr
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6121 2 L 45° - 45°Window frame (horizontal)
AH260-RG6121 2 H 45° - 45°Window frame (vertical)
AH260-RG6211 2 L1-31 45° - 45°Window sash (horizontal) ( = SW1)
AH260-RG6211 2 L2-31 45° - 45°Window sash (horizontal) ( = SW2)
Gaskets Dimension
AE004-904015-00 2L+3HStroke gasket inside
AE004-904935-00 2L+3HCentral gasket
AE004-904002-80 2L+4HGlazing gasket inside
Glass Length
Glass1 SW1-116For right sash
Pcs Height
1 SH-116
AE004-904405-00 2L+4HGlazing gasket outside
Optionally Pcs.
8Vulcanized corner joints
AH260-RG6211 4 H-56 45° - 45°Window sash (vertical) ( = SH)
AH260-RG6260 1 SH-72 90° - 90°Rebate profile
GB1 SW1-102 90° - 90°Glazing bead horizontal (right) 2
GB2 SW2-102 90° - 90°Glazing bead horizontal (left) 2
GB3 SH-146 90° - 90°Glazing bead vertical 4
Glass2 SW2-116For left sash 1 SH-116
Same dimensions for AH260-RG6214
H
L
AE011-903000-19
Turn, Turn and Tilt Window
AH
260-
RG
6121
AH
260-
RG
6211
AE
004-
9040
15-0
0
AE
004-
9049
35-0
0A
E00
4-90
4405
-00
AE
004-
9040
02-8
0
GB 3
HSW
GB1,GB2
GB3 GB3GB3GB3
SW1SW2
L
L1L2
AH260-RG6211AH260-RG6260
AE004-904015-00
AE00
4-90
4935
-00
AE004-904405-00AH260-RG6211
AE004-904002-80
AE004-904405-00AE004-904935-00
AE004-904015-00 AH260-RG6211
AH260-RG6121
80
June 2012
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6131 2 L 45° - 45°Window frame (horizontal)
2 H 45° - 45°Window frame (vertical)
AH260-RG6220 2 L1-41 45° - 45°Window sash (horizontal) ( = SW1)
2 L2-41 45° - 45°Window sash (horizontal) ( = SW2)
Gaskets Dimension
AE004-904015-00 2L+3HStroke gasket inside
AE004-904935-00 2L+3HCentral gasket
AE004-904002-80 2L+4HGlazing gasket inside
Glass Length
Glass1 SW1-168For right sash
Pcs Height
1 SH-168
AE004-904405-00 2L+4HGlazing gasket outside
Optionally Pcs.
AE011-903000-22 8Vulcanized corner joints
4 H-76 45° - 45°Window sash (vertical) ( = SH)
AH260-RG6260 1 SH-72 90° - 90°Rebate profile
GB1 SW1-154 90° - 90°Glazing bead horizontal (right) 2
GB2 SW2-154 90° - 90°Glazing bead horizontal (left) 2
GB3 SH-198 90° - 90°Glazing bead vertical 4
Glass2 SW2-168For left sash 1 SH-168
Same dimensions for AH260-RG6222
L
H
AH260-RG6131
AH260-RG6220
AH260-RG6220
Turn, Turn and Tilt Window
AH260-RG6220AH260-RG6131
GB3
AE004-904002-80AE004-904002-80
AH260-RG6220
AH260-RG6260
AH260-RG6220AH260-RG6131
SW2SW1
L1L2
L
AE004-904405-00AE004-904935-00
AE004-904015-00
AE004-904405-00
AE004-904015-00
AE004-904405-00AE004-904935-00 AE004-904405-00 AE004-904935-00
AE004-904015-00
81
www.balkan.gr
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-5060030 2 L 45° - 45°Window frame (horizontal)
AH260-5060030 2 H 45° - 45°Window frame (vertical)
AH260-RG6211 2 L-87 45° - 45°Window sash (horizontal) ( = SW)
AH260-RG6211 2 H-87 45° - 45°Window sash (vertical) ( = SH)
GB1 SW-102 90° - 90°Glazing bead horizontal 2
GB2 SH-146 90° - 90°Glazing bead vertical 2
Gaskets Dimension
AE004-904015-00 2L+2HStroke gasket inside
AE004-904935-00 2L+2HCentral gasket
AE004-904002-80 2L+2HGlazing gasket inside
Glass Length
Glass SW-116For sash
Pcs Height
1 SH-116
AE004-904405-00 2L+2HGlazing gasket outside
Optional Pcs.
4Vulcanized corner joints
Same dimensions for AH260-RG6214
( = LM-24)
( = HM-24)
AA010-070-00 2L+2HGlazing gasket inside
HM
LM
AE011-903000-19
Turn, Turn and Tilt Window
AH
260-
5060
030
AH
260-
RG
6211
AE
004-
9044
95-0
0AE
004-
9040
15-0
0
AE
004-
9044
05-0
0A
E00
4-90
4935
-00
SH
HM
H=H
M-2
4
AE
004-
9040
02-8
0GB1
AH260-5060030
AH260-RG6211
AE004-904495-00
AE004-904015-00
AE004-904405-00AE004-904935-00 AH260-5060030
AH260-RG6211
AE004-904495-00
AE004-904015-00
AE004-904405-00
AE004-904935-00
SW
L=LM-24
LM
GB2
82
June 2012
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-5060030 2 L 45° - 45°Window frame (horizontal)
AH260-5060030 2 H 45° - 45°Window frame (vertical)
AH260-RG6211 2 L1-46,5 45° - 45°Window sash (horizontal) ( = SW1)
AH260-RG6211 2 L2-46,5 45° - 45°Window sash (horizontal) ( = SW2)
Gaskets Dimension
AE004-904015-00 2L+3HStroke gasket inside
AE004-904935-00 2L+3HCentral gasket
AE004-904002-80 2L+4HGlazing gasket inside
Glass Length
Glass1 SW1-116For right sash
Pcs Height
1 SH-116
AE004-904405-00 2L+4HGlazing gasket outside
Optionally Pcs.
8Vulcanized corner joints
AH260-RG6211 4 H-87 45° - 45°Window sash (vertical) ( = SH)
AH260-RG6260 1 SH-72 90° - 90°Rebate profile
GB1 SW1-102 90° - 90°Glazing bead horizontal (right) 2
GB2 SW2-102 90° - 90°Glazing bead horizontal (left) 2
GB3 SH-146 90° - 90°Glazing bead vertical 4
Glass2 SW2-116For left sash 1 SH-116
Same dimensions for AH260-RG6214
AA010-007-00 2L+2HGlazing gasket inside
( = LM-24)
( = HM-24)
HM
LM
AE011-903000-19
Turn, Turn and Tilt Window
AH
260-
5060
030
AH
260-
RG
6211
AE
004-
9044
95-0
0A
E00
4-90
4015
-00
AE
004-
9044
05-0
0A
E00
4-90
4935
-00
HM
H=H
M-2
4
SH
AE
004-
9040
02-8
0
GB1,GB2
GB3GB3
SW1SW2
L1L2
L=LM-24
LM
AH260-RG6211AH260-RG6260
AE00
4-90
4935
-00
AE004-904405-00
AH260-RG6211AE004-904935-00
AE004-904405-00
AE004-904015-00AE004-904495-00
AH260-RG6211
AH260-5060030AE004-904935-00
AE004-904405-00
AE004-904015-00AE004-904495-00
AH260-RG6211
AH260-5060030
83
www.balkan.gr
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6121 2 L 45° - 45°Window frame (horizontal)
AH260-RG6121 2 H 45° - 45°Window frame (vertical)
AH260-RG6215 2 L-56 45° - 45°Window sash (horizontal) ( = SW)
Gaskets Dimension
AE004-904015-00 2L+2HStroke gasket inside
AE004-904935-00 2L+2HCentral gasket
AE004-904002-80 2L+2HGlazing gasket inside
Glass Length
Glass SW-126For right sash
Pcs Height
1 SH-126
AE004-904405-00 2L+2HGlazing gasket outside
Optionally Pcs.
4Vulcanized corner joints
LH
L
H
AH260-RG6215 2 H-56 45° - 45°Window sash (vertical) ( = SH)
GB1 SW-112 90° - 90°Glazing bead horizontal 2
GB2 SH-156 90° - 90°Glazing bead vertical 2
AE011-903000-19
Turn, Turn and Tilt Window
AE
004-904015-00
AE
004-904935-00
AH
260-RG
6215
AH
260-RG
6121
AE
004-904405-00
AE
004-904002-80
HSH
GB1
GB1, GB2
AE004-904015-00
AE004-904935-00
AH260-RG6215
AH260-RG6121
AE004-904405-00
AE004-904002-80
L
SW
GB
2
GB
2
84
June 2012
RG60 Catalogue
H
L
Profiles Pcs Dimension Cutting
AH260-RG6121 2 L 45° - 45°Window frame (horizontal)
AH260-RG6121 2 H 45° - 45°Window frame (vertical)
AH260-RG6215 2 L1-31 45° - 45°Window sash (horizontal) ( = SW1)
AH260-RG6215 2 L2-31 45° - 45°Window sash (horizontal) ( = SW2)
Gaskets Dimension
AE004-904015-00 2L+3HStroke gasket inside
AE004-904935-00 2L+3HCentral gasket
AE004-904002-80 2L+4HGlazing gasket inside
Glass Length
Glass1 SW1-116For right sash
Pcs Height
1 SH-116
AE004-904405-00 2L+4HGlazing gasket outside
Optionally Pcs.
8Vulcanized corner joints
AH260-RG6215 4 H-56 45° - 45°Window sash (vertical) ( = SH)
AH260-RG6261 1 SH-72 90° - 90°Rebate profile
GB1 SW1-102 90° - 90°Glazing bead horizontal (right) 2
GB2 SW2-102 90° - 90°Glazing bead horizontal (left) 2
GB3 SH-146 90° - 90°Glazing bead vertical 4
Glass2 SW2-116For left sash 1 SH-116
Same dimensions for AH260-RG6214
AE011-903000-19
Turn, Turn and Tilt Window
AE
004-904015-00
AE
004-904935-00
AH
260-RG
6215
AH
260-RG
6121
AE
004-904405-00
AE
004-904002-80
HSH
GB3
GB1, GB2
GB3 GB3
AE004-904935-00
L
L1L2
SW1SW2AE004-904015-00
AE004-904 002-80
AE004-904405-00
AH260-RG6121AH260-RG6215
AH260-RG6211AH260-RG6261
AE004-904935-00
AE004-904015-00
AE004-904405-00 AH260-RG6211
85
www.balkan.gr
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6301 1 L 45° - 45°Door frame (top)
1 H 90° - 45°Door frame (left)
1 H 45° - 90°Door frame (right)
AH260-RG6330 1 H-58 90° - 45°Door sash (left) ( = SH)
1 H-58 45° - 90°Door sash (right) ( = SH)
1 L-100 45° - 45°Door sash (top) ( = SW)
AH260-RG6395 1 SW-148 90° - 90°Base profile
GB1 SW-148 90° - 90°Glazing bead horizontal 2
GB2 SH-227 90° - 90°Glazing bead vertical 2
Gaskets Dimension
AE004-904035-00 2L+4HStroke gasket inside + outside
AE004-904002-80 1L+2HGlazing gasket inside
AE004-904405-00 1L+2HGlazing gasket outside
Glass Length
Glass SW-162For sash
Pcs Height
1 SH-197
H
L
AH260-RG6301
AH260-RG6301
AH260-RG6301
AH260-RG6330
Inward Opening Door
GB1
AE
004-
9040
02-8
0
AH
275-
RG
6395
8S
H
H
AE
004-
9044
05-0
0
AE
004-
9040
35-0
0A
H26
0-R
G63
01A
H27
5-R
G63
30
AH275-RG6330 AH260-RG6301AE004-904035-00
AE004-904405-00
SW
L
GB2
86
June 2012
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6311 1 L 45° - 45°Door frame (top)
1 H 90° - 45°Door frame (left)
1 H 45° - 90°Door frame (right)
AH260-RG6335 1 L-100 45° - 45°Door sash (top) ( = SW)
1 H-58 90° - 45°Door sash (left) ( = SH)
1 H-58 45° - 90°Door sash (right) ( = SH)
AH260-RG6395 1 SW-148 90° - 90°Base profile
GB1 SW-148 90° - 90°Glazing bead horizontal 2
GB2 SH-227 90° - 90°Glazing bead vertical 2
Gaskets Dimension
AE004-904035-00 2L+4HStroke gasket inside + outside
AE004-904405-00 1L+2HGlazing gasket outside
AE004-904002-80 1L+2HGlazing gasket inside
Glass Length
Glass SW-162For sash
Pcs Height
1 SH-197
OUTWARD OPENING DOOR
AH260-RG6311
AH260-RG6311
AH260-RG6335
AH260-RG6335
H
L
Outward Opening Door
GB1
GB1
AE
004-
9040
02-8
0
8S
H
AH
260-
RG
6395
HH
AE
004-
9040
35-0
0A
H26
0-R
G63
11A
H26
0-R
G63
35
AE
004-
9044
05-0
0
AH275-RG6330 AH260-RG6301AE004-904035-00
AE004-904405-00
SW
L
GB2
87
www.balkan.gr
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6301 1 L 45° - 45°Door frame (top)
1 H 90° - 45°Door frame (left)
1 H 45° - 90°Door frame (right)
AH260-RG6335 1 H-58 45° - 45°Door sash ( = SH)
AH260-RG6330 2 H-58 90° - 45°Door sash (left) ( = SH)
AH260-RG6330 1 H-58 45° - 90°Door sash (right) ( = SH)
AH260-RG6330 1 L2-40 45° - 45°Door sash (top left) ( = SW2)
AH260-RG6335 1 L1-40 45° - 45°Door sash (top right) ( = SW1)
AH260-RG6395 1 SW2-148 90° - 90°Base profile (left)
AH260-RG6395 SW1-148 90° - 90°Base profile (right) 1
GB1 SW1-148 90° - 90°Glazing bead horizontal 2
GB2 SW2-148 90° - 90°Glazing bead horizontal 2
GB3 SH-227 90° - 90°Glazing bead vertical 4
Gaskets Dimension
AE004-904035-00 2L+6HStroke gasket inside + outside
AE004-904002-80 2L+4HGlazing gasket outside
AE004-904405-00 2L+4HGlazing gasket inside
Glass Length
Glass 1 SW1-162For right sash
Pcs Height
1 SH-197
Glass 2 SW2-162For left sash 1 SH-197
H
L
AH260-RG6301
AH260-RG6301
Inward Opening Door
GB1,GB2
AE
004-
9040
02-8
0
AH
260-
RG
6395
8S
H
HA
E00
4-90
4405
-00
AE
004-
9040
35-
00A
H26
0-R
G63
01A
H27
5-R
G63
30
AH260-RG6335
AE004-904405-00
AH260-RG6330AE004-904035-00
SW2
SW1L1L2
L
AH275-RG6330 AH260-RG6301AE004-904035-00
AE004-904405-00
GB
3
GB
3
88
June 2012
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6311 1 L 45° - 45°Door frame (top)
AH260-RG6311 1 H 45° - 90°Door frame (left)
1 H 90° - 45°Door frame (right)
AH260-RG6330 1 H-58 45° - 90°Door sash ( = SH)
AH260-RG6335 1 H-58 45° - 90°Door sash (left) ( = SH)
2 H-58 90° - 45°Door sash (right) ( = SH)
1 L2-40 45° - 45°Door sash (top left) ( = SW2)
1 L1-40 45° - 45°Door sash (top right) ( = SW1)
AH260-RG6395 1 SW2-148 90° - 90°Base profile (left)
AH260-RG6395 SW1-148 90° - 90°Base profile (right) 1
GB1 SW1-148 90° - 90°Glazing bead horizontal 2
GB2 SW2-148 90° - 90°Glazing bead horizontal 2
GB3 SH-227 90° - 90°Glazing bead vertical 4
Gaskets Dimension
AE004-904035-00 2L+6HStroke gasket inside + outside
AE004-904003-30 2L+4HGlazing gasket outside
AE004-904002-80 2L+4HGlazing gasket inside
Glass Length
Glass 1 SW1-162For right sash
Pcs Height
1 SH-197
Glass 2 SW2-162For left sash 1 SH-197
L
H
AH260-RG6311
AH260-RG6335
AH260-RG6335
AH260-RG6335
Outward Opening Door
GB1,GB2
AE
004-
9040
02-8
0
8S
H
AH
260-
RG
6395
HH
AE
004-
9040
35-0
0A
H26
0-R
G63
11A
H26
0-R
G63
35
AE
004-904405-00
AH260-RG6330
AE004-904405-00
AH260-RG6335AE004-904035-00 AH260-RG6335 AH260-RG6311AE004-904035-00AH260-RG6335AH260-RG6311 AE004-904035-00
SW2
SW1L1L2
L
GB3
89
www.balkan.gr
RG60 Catalogue
Profiles Pcs Dimension Cutting
AH260-RG6131 1 L 45° - 45°Door frame (top)
1 H 90° - 45°Door frame (left)
1 H 45° - 90°Door frame (right)
AH900-TF269 1 L-78 45° - 45°Aditional profile (top)
AH900-TF269 1 H-39 90° - 45°
AH900-TF269 1 H-39 45° - 90°
Aditional profile (left)
Aditional profile (left)
AH260-RG6330 1 L1-38 45° - 45°Door sash (top right) ( = SW1)
L2-38 45° - 45°1Door sash (top left) ( = SW2)
H-56 90° - 45°2Door sash ( = HS)
H-56 45° - 90°1AH260-RG6335 Door sash ( = HS)
AH260-RG6395 1 SW1-148 90° - 90°Base profile(right)
AH260-RG6395 1 SW2-148 90° - 90°Base profile(left)
GB1 SW1-148 90° - 90°Glazing bead horizontal (right) 2
GB2 HS-227 90° - 90°Glazing bead vertical (right) 2
GB3 SW2-122 90° - 90°Glazing bead horizontal (left) 2
GB4 HS-227 90° - 90°Glazing bead vertical (left) 2
Gaskets Dimension
AE004-904035-00 2L+6HStroke gasket inside + outside
AE004-904405-00 1L+4HGlazing gasket outside
AE004-904002-80 1L+4HGlazing gasket inside
Glass Length
Glass1 SW1-162For right sash
Pcs Height
1 SH-197
Cutting dimension for AE013-929170-00 are the same with AH900-TF269
Glass2 SW2-162For left sash 1 SH-197
H-56 45° - 90°1Door sash ( = HS)
H
L
AH260-RG6131
AH260-RG6131
AH260-RG6330
AH260-RG6330
AH260-RG6330
Inward Opening Door
GB1,GB3
AE
004-
9040
02-8
0
AH
260-
RG
6395
8S
H
H
AE
004-
9044
05-0
0
AE
004-
9040
35-0
0A
H26
0-R
G63
11A
H27
5-R
G63
30
AH260-RG6335
AE004-904405-00
AH260-RG6330AE004-904035-00
L
L2 L1SW1
SW2AH260-RG6330 AH260-RG6311AE004-904035-00
AE004-904405-00
GB
2
GB
4
AH275-RG6330AH260-RG6311
90
June 2012
RG60 Catalogue
L
H
Profiles Pcs Dimension Cutting
AH260-RG6131 1 L 45° - 45°Door frame (top)
1 H 90° - 45°Door frame (left)
1 H 45° - 90°Door frame (right)
AH260-RG6350 1 L-83 45° - 45°Aditional profile (top)
1 H-41,5 90° - 45°
1 H-41,5 45° - 90°
Aditional profile (left)
Aditional profile (left)
AH260-RG6335 1 L1-64 45° - 45°Door sash (top right) ( = SW1)
L2-64 45° - 45°1Door sash (top left) ( = SW2)
H-82 90° - 45°2Door sash ( = HS)
H-82 45° - 90°1AH260-RG6330 Door sash ( = HS)
AH260-RG6395 1 SW1-148 90° - 90°Base profile(right)
1 SW2-148 90° - 90°Base profile(left)
GB1 SW1-148 90° - 90°Glazing bead horizontal (right) 2
GB2 HS-227 90° - 90°Glazing bead vertical 4
GB3 SW2-148 90° - 90°Glazing bead horizontal (left) 2
Gaskets Dimension
AE004-904035-00 2L+6HStroke gasket inside + outside
AE004-904405-00 1L+4HGlazing gasket outside
AE004-904002-80 1L+4HGlazing gasket inside
Glass Length
Glass1 SW1-162For right sash
Pcs Height
1 SH-197
AA010-007-00 1L+2HGlazing gasket inside
Glass2 SW2-162For left sash 1 SH-197
H-82 45° - 90°1Door sash ( = HS)
AH260-RG6131
AH260-RG6131
AH260-RG6350
AH260-RG6350
AH260-RG6335
AH260-RG6335
AH260-RG6335
AH260-RG6395
Outward Opening Door
GB1,GB3
AE
004-
9040
02-8
0
8
AH
260-
RG
6331
SH
AH
260-
RG
6395
H
AE
004-
9040
35-0
0
AH
260-
RG
6350
AH
260-
RG
6335
AE
004-904405-00
AH260-RG6330
AE004-904405-00
AH260-RG6335AE004-904035-00 AH260-RG6335 AE004-904035-00AH260-RG6335AE004-904035-00
SW2
SW1L1L2
L
GB2
AH260-RG6350AH260-RG6131
AH260-RG6350AH260-RG6131
91
www.balkan.gr
RG60 Catalogue
Inward Opening Door
Profiles Pcs Dimension Cutting
AH260-5060030 1 L 45° - 45°Door frame (top)
1 H 90° - 45°Door frame (left)
1 H 45° - 90°Door frame (right)
AH900-TF269 1 L-89 45° - 45°Aditional profile (top)
AH900-TF269 1 H-44,5 90° - 45°
AH900-TF269 1 H-44,5 45° - 90°
AH260-RG6330 1 L-107 45° - 45°Door sash (top)
H-61,5 90° - 45°1
H-61,5 45° - 90°1
Gaskets Dimension
AE004-904035-00 2L+4HStroke gasket inside + outside
AE004-904405-00 1L+2HGlazing gasket outside
AE004-904002-80 1L+2HGlazing gasket inside
Glass Length
Glass SW-162For sash
Pcs Height
1 SH-197
( = LM-24)
( = HM-12)
( = HM-12)
Aditional profile (left)
Aditional profile (left)
( = SW)
Door sash (left) ( = SH)
Door sash (right) ( = SH)
AH260-RG6395 1 SW-148 90° - 90°Base profile
GB1 SW-148 90° - 90°Glazing bead horizontal 2
GB2 SH-227 90° - 90°Glazing bead vertical 2
AA010-007-00 1L+2HGlazing gasket inside
Cutting dimension for AE013-929170-00 are the same with AH900-TF269
AH260-5060030
AH260-5060030
AH260-RG6330
AH260-RG6330
HM
LM AH
260-
5060
030
AH
260-
RG
6330
AH900-TF269 PK270AE004-904035-00
AE
004-
9044
05-0
0
AH
260-
RG
6395
GB1
AE
004-
9040
02-8
0
8S
H
H=H
M-1
2
AH260-5060030AH260-RG6330
AH900-TF269
PK
270
AE004-904035-00
AE004-904405-00AH260-5060030AH260-RG6330
AH900-TF269
PK
270
GB2
SW
L=LM-24
LM
92
June 2012
RG60 Catalogue
Outward Opening Door
Profiles Pcs Dimension Cutting
AH260-5060030 1 L 45° - 45°Door frame (top)
AH260-5060030 1 H 90° - 45°Door frame (left)
AH260-5060030 1 H 45° - 90°Door frame (right)
AH260-RG6350 1 L-99 45° - 45°Aditional profile (top)
AH260-RG6350 1 H-49,5 90° - 45°
AH260-RG6350 1 H-49,5 45° - 90°
AH260-RG6335 1 L-157 45° - 45°Door sash (top)
H-87,5 90° - 45°1
H-87,5 45° - 90°1
Gaskets Dimension
AE004-904035-00 2L+4HStroke gasket inside + outside
AE004-904405-00 1L+2HGlazing gasket outside
AE004-904002-80 1L+2HGlazing gasket inside
Glass Length
Glass SW-162For sash
Pcs Height
1 SH-197
( = LM-24)
( = HM-12)
( = HM-12)
Aditional profile (left)
Aditional profile (left)
( = SW)
AH260-RG6335 Door sash (left) ( = SH)
AH260-RG6335 Door sash (right) ( = SH)
AH260-RG6395 1 SW-148 90° - 90°Base profile
GB1 SW-148 90° - 90°Glazing bead horizontal 2
GB2 SH-227 90° - 90°Glazing bead vertical 2
AA010-007-00 1L+2HGlazing gasket inside
HM
LM
GB1
AE
004-
9040
02-8
0H=H
M-1
2
SH
8
AH
260-5060030
AH
260-
RG
6335
AH
260-
RG
6395
AE004-904495-00
AE004-904035-00
AE
004-
9044
05-0
0
AH
260-RG
6350
AH260-RG6335AH260-RG6350
AH260-5060030
AE004-904405-00
AE004-904035-00
AE
004-904495-00
SW
L=LM-24
93
www.balkan.gr
RG60 Catalogue
Inward Opening Door
Profiles Pcs Dimension Cutting
AH260-5060030 1 L 45° - 45°Door frame (top) ( = LM-24)
1 H 90° - 45°Door frame (left) ( = HM-12)
1 H 45° - 90°Door frame (right) ( = HM-12)
AH900-TF269 1 L-89 45° - 45°Aditional profile (top)
AH900-TF269 1 H-44,5 90° - 45°
AH900-TF269 1 H-44,5 45° - 90°
Aditional profile (left)
Aditional profile (left)
AH260-RG6330 1 L1-43,5 45° - 45°Door sash (top right) ( = SW1)
L2-43,5 45° - 45°1Door sash (top left) ( = SW2)
H-61,5 90° - 45°2Door sash ( = HS)
H-61,5 45° - 90°1AH260-RG6335 Door sash ( = HS)
AH260-RG6395 1 SW1-148 90° - 90°Base profile(right)
AH260-RG6395 1 SW2-148 90° - 90°Base profile(left)
GB1 SW1-148 90° - 90°Glazing bead horizontal (right) 2
GB2 HS-227 90° - 90°Glazing bead vertical (right) 2
GB3 SW2-148 90° - 90°Glazing bead horizontal (left) 2
GB4 HS-227 90° - 90°Glazing bead vertical (left) 2
Gaskets Dimension
AE004-904035-00 2L+6HStroke gasket inside + outside
AE004-904405-00 1L+4HGlazing gasket outside
AE004-904002-80 1L+4HGlazing gasket inside
Glass Length
Glass1 SW1-162For right sash
Pcs Height
1 SH-197
AA010-007-00 1L+2HGlazing gasket inside
Cutting dimension for AE013-929170-00 are the same with AH900-TF269
Glass2 SW2-162For left sash 1 SH-197
H-61,5 45° - 90°1Door sash ( = HS)
HM
LM
AH260-5060030
AH260-5060030
AH260-RG6330
AH260-RG6330
AH260-RG6330
AE
004-
9040
02-8
0GB1, GB3
HM
H=H
M-1
2
SH
8
AH
260-
RG
6395
AE
004-
9044
05-0
0
AE004-904035-00PK270
AH900-TF269
AH
260-
RG
6330
AH
260-
5060
030
AH260-5060030AH260-RG6330
AH900-TF269
PK
270
AE004-904035-00
AA010-007-00
AH260-5060030 AH260-RG6330
AH900-TF269
PK
270
AE004-904035-00
AE004-904405-00
AA010-007-00 AH260-RG6335
AE004-904405-00
AH260-RG6330AE004-904035-00
GB
4
GB
2
SW2
LM
L2 L1
L
94
June 2012
RG60 Catalogue
Outward Opening Door
Profiles Pcs Dimension Cutting
AH260-5060030 1 L 45° - 45°Door frame (top) ( = LM-24)
1 H 90° - 45°Door frame (left) ( = HM-12)
1 H 45° - 90°Door frame (right) ( = HM-12)
AH260-GR6350 1 L-99 45° - 45°Aditional profile (top)
AH900-TF269 1 H-49,5 90° - 45°
AH900-TF269 1 H-49,5 45° - 90°
Aditional profile (left)
Aditional profile (left)
AH260-RG6335 1 L1-69,5 45° - 45°Door sash (top right) ( = SW1)
L2-69,5 45° - 45°1Door sash (top left) ( = SW2)
H-87,5 90° - 45°2Door sash ( = HS)
H-87,5 45° - 90°1AH260-RG6330 Door sash ( = HS)
AH260-RG6395 1 SW1-148 90° - 90°Base profile(right)
AH260-RG6395 1 SW2-148 90° - 90°Base profile(left)
GB1 SW1-148 90° - 90°Glazing bead horizontal (right) 2
GB2 HS-227 90° - 90°Glazing bead vertical (right) 2
GB3 SW2-148 90° - 90°Glazing bead horizontal (left) 2
GB4 HS-227 90° - 90°Glazing bead vertical (left) 2
Gaskets Dimension
AE004-904035-00 2L+6HStroke gasket inside + outside
AE004-904405-00 1L+4HGlazing gasket outside
AE004-904002-80 1L+4HGlazing gasket inside
Glass Length
Glass1 SW1-162For right sash
Pcs Height
1 SH-197
AA010-007-00 1L+2HGlazing gasket inside
Glass2 SW2-162For left sash 1 SH-197
H-87,5 45° - 90°1Door sash ( = HS)
HM
LM
AH260-5060030
AH260-5060030
AH260-RG6335
AH260-RG6335
AH260-RG6335
GB1,GB3
AE
004-
9040
02-8
0
HM
H=H
M-1
2
SH
8
AH
260-5060030
AH
260-
RG
6335
AH
260-
RG
6395
AE004-904495-00
AE004-904035-00
AE
004-
9044
05-0
0
AH
260-RG
6350
AE004-904035-00
AE004-904495-00
AH260-RG6335 AH260-RG6350AH260-5060030
AE004-904405-00
AE004-904035-00AE004-904495-00
AH260-RG6335AH260-5060030
AH260-RG6350 AH260-RG6330
AE004-904405-00
AH260-RG6335AE004-904035-00
GB2GB4
Working Pages
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
RG75 C
June 2012
Catalogue
www.balkan.gr
148
June 2012
RG60 CatalogueBALKAN NETWORK
GREECE - BALKAN SA www.balkan.grHead Offi ce: Athens11th km Nat.Road Athens-Lamia, 144 52 MetamorphosiTel.: +30 210 2810 030, Fax: +30 210 2845 025e-mail: [email protected]
Iraklio: +30 2810 370555-6, Fax: +30 2810 311 400Larissa: +30 2410 555 641-2, Fax: +30 2410 288 919Τhessaloniki: +30 2310 753 454, Fax: +30 2310 753 455Τhiva: Tel.: +30 22620 72001-4, Fax: +30 22620 71293
Extrusion Industry79th km Nat. Road Athens-Lamia, Ipato ThivonTel.: +30 22620 72068, Fax: +30 22620 71293e-mail: [email protected]
ROMANIA - BALKAN RO www.balkanro.roHead Offi ce: BucharestB-dul Iuliu Maniu 333, Sector 6Tel.: +40 213 170 695-7-8, Fax: +40 213 160 699e-mail: [email protected]
Alba Iulia: +40 258 810 241, Arad: +40 257 288 588, Bacau: +40 234 562 620Βrasov: +40 286 549 904, Cluj-Napoca: +40 264 415 512, Constanta: +40 241 559 850Craiova: +40 251 483 323, Iasi: +40 232 244 055, Τimisoara: +40 256 296 114
DEALERSGalati: Alprovest, tel/fax: +40 236 458 038, Pitesti: Conarg, tel/fax: +40 248 610 089Satu Mare: Neptun, tel/fax: + 40 261 841 930, Sibiu: Roa Design, tel/fax: +40 269 214 325Ploiesti: Rolir, tel/fax: +40 244 225 170
UKRAINE - BALKAN UAHead Offi ce: KievMoskovsky Av. 6Tel./Fax: +38 044 464 4947/7858
Κharkov: +380 57 757 5161-2Odessa: +380 482 328 402, 335 654, 0487 773 389
BULGARIA - BLK BG www.blk-bg.comΗead Offi ce: Sofi a8 Malashevska Str. 1202Tel.: +359 2 936 6652/91, Fax:+359 2 936 6735e-mail: offi [email protected]
CZECH REPUBLICALUMONT BUILDING A.S. DEALERHradni-Slazska 27/37, 710 00 OstravaTel./Fax: +420 777 800333e-mail: [email protected]
RUSSIAMGM LTD DEALERPromzona 16 Str.-Armavir, 352916 KrasnodarTel./Fax: +7 86137 58100e-mail: [email protected]
BELARUSSOL-FARM DEALERKalvariyskaya 60/2H, 220073 MinskTel./Fax: +37517 204 22 25e-mail: [email protected]
IRANALUMIN.CoNo 6 8th Floor, Negar Tower, Vanak Sq. TeheranTel.: +9821 8864 1422, Fax: +9821 8864 1425 Inspired with passion!