service manual - freej.mdownload1.free.fr/schemas/jvc/hr-j282_283_285_290_293...important safety...
TRANSCRIPT
SERVICE MANUAL
No.82915June 2002
HR-J282EU, HR-J283EU, HR-J285EU,HR-J290EU, HR-J293EU, HR-J295EK, HR-J295MS,
HR-J582EU, HR-J583EU, HR-J585EU,HR-J590EU, HR-J593EU, HR-J595EK, HR-J595MS
VIDEO CASSETTE RECORDER
SPECIFICATIONS (The specifications shown pertain specifically to the model HR-J290EU, J293EU, J590EU and J593EU.)
This service manual is printed on 100% recycled paper.COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD
V15
Specifications shown are for SP mode unless specified otherwise.E. & O.E. Design and specifications subject to change without notice.
GENERALPower : 200 V – 240 V , 50 Hz/60 HzPower consumption
Power on : Approx. 12 WStandby mode : 3.0 W
Video Head systemHR-J590/J593/J599EU
: DA4 (Double Azimuth) head helical scan system
HR-J290/J293EU : Rotary two-head helical scan systemTape speed
(SP) : 23.39 mm/sec(LP)* : 11.69 mm/sec* HR-J590/J593/J599EU only
Tape format : Tape width 1/2" (12.7 mm high density VHS tape)
Maximum recording time(SP) : 240 min. with E-240 video cassette(LP)* : 480 min. with E-240 video cassette* HR-J590/J593/J599EU only
Rewind time : Approx. 180 sec. with E-180 cassetteDimensions (W x H x D) : 360 mm x 94.5 mm x 270 mmWeight : 4.0 kgOperating temperature : 5°C to 35°COperating humidity : Less than 80 %Timer : 24 hours display type
VIDEOSignal system : PAL-type colour signal and CCIR
monochrome signal, 625 lines 50 fields
Recording Format : PAL/MESECAMRF reception : PAL (B/G)/SECAM (B/G)RF OUT : PAL GRF modulator : UHF channels 22 – 68 (Adjustable)Input level : VIDEO IN (SCART type)
1.0 Vp-p, 75 ohm, unbalancedOutput level : VIDEO OUT (SCART type)
1.0 Vp-p, 75 ohm, unbalancedSignal-to-noise ratio : More than 43 dBm
AUDIOInput level : AUDIO IN (SCART type)
–6.0 dBm, more than 10 kΩOutput level
HR-J590/J593/J599EU
: AUDIO OUT (SCART, RCA type)–6.0 dBm, less than 1 kΩ
HR-J290/J293EU : AUDIO OUT (SCART type)–6.0 dBm, less than 1 kΩ
Audio trackHR-J590/J593/J599EU
: Mono track and Hi-Fi track
HR-J290/J293EU : Mono trackAudio frequency response
Normal audio : 100 Hz to 10,000 Hz(–6/+3 dBm)
Hi-Fi audio* : 20 Hz to 20,000 Hz(–3/+3 dBm)
* HR-J590/J593/J599EU onlyAudio signal to noise ratio [HR-J590/J593/J599EU only]
Hi-Fi audio : More than 70 dB (JIS A filter)Audio dynamic range [HR-J590/J593/J599EU only]
Hi-Fi audio : More than 85 dB (JIS A filter)
ACCESSORIESProvided accessories : RF cable,
Infrared remote control unit,“R3” battery x 2
TABLE OF CONTENTS
SECTION 1SUMMARY
KEY TO ABBREVIATIONS . . . . . . . . . . . . . . . . 1-1IMPORTANT SAFETY PRECAUTIONS . . . . . . . . . . 1-2
PROPOSAL FOR APPLYING SHORTPROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4SERVICE NOTICE ON REPLACING EEPROM . .1-5SERVICE INFORMATION FOR EEPROMIC SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . 1-7
SECTION 2CABINET & MAIN CHASSIS
SERVICE METHOD . . . . . . . . . . . . . . . . . . . . . 2-1Electrical Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
EXPLODED VIEWS . . . . . . . . . . . . . . . . . . . . . . 2-21. Cabinet & Main Frame Section . . . . . . . . . . . . . 2-2
2. Packing & Accessory Section . . . . . . . . . . . . . . 2-3
SECTION 3ELECTRICAL
ELECTRICAL ADJUSTMENT POINTSARRANGEMENT . . . . . . . . . . . . . . . . . . . . . . . .3-1ELECTRICAL ADJUSTMENT PROCEDURES . . 3-2
1. Servo Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
ELECTRICAL TROUBLESHOOTING GUIDE . . . 3-41. Power Circuit(SMPS) . . . . . . . . . . . . . . . . . . . . . 3-4
2. Servo Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
3. System & Front Panel Circuit . . . . . . . . . . . . . . .3-10
4. Y/C Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
5. Tuner/IF Circuit . . . . . . . . . . . . . . . . . . . . . . . . .3-16
6. Hi-Fi Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . .3-211. Power Block Diagram . . . . . . . . . . . . . . . . . . . .3-21
2. Tuner/IF, NICAM & A2 Block Diagram . . . . . . . .3-23
3. VPS Block Diagram . . . . . . . . . . . . . . . . . . . . . .3-24
4. Y/C Block Diagram . . . . . . . . . . . . . . . . . . . . . .3-25
5. Hi-Fi Block Diagram . . . . . . . . . . . . . . . . . . . . .3-26
6. System Block Diagram . . . . . . . . . . . . . . . . . . .3-27
CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . .3-291. Power Circuit Diagram . . . . . . . . . . . . . . . . . . . .3-29
2. Tuner, NICAM/A2 Circuit Diagram . . . . . . . . . . .3-31
3. A/V, SECAM, VPS Circuit Diagram . . . . . . . . . .3-33
4. System Circuit Diagram . . . . . . . . . . . . . . . . . . .3-35
5. Hi-Fi, SCART Circuit Diagram . . . . . . . . . . . . . .3-39
• CIRCUIT VOLTAGE CHART . . . . . . . . . . . . . . . .3-41
PRINTED CIRCUIT BOARD DIAGRAMS . . . . .3-451. MAIN P.C.Board . . . . . . . . . . . . . . . . . . . . . . . .3-45
SECTION 4MECHANISM
SECTION 5REPLACEMENT PARTS LIST
5-1 EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . .5-1
5-2 REPLACEMENT PARTS LIST
.
. . . . . . . . . . . . . . . . .5-4
NOTE) The table of contents for this section is editedNOTE) separately.
1-1
A AC :Alternating CurrentACC :Automatic Color ControlACSS :Automatic Channel Setting SystemADJ :AdjustA/E :Audio EraseAFC :Automatic Frequency ControlAFT :Automatic Fine TuningAGC :Automatic Gain ControlA.H.SW :Audio Head SwitchALC :Automatic Level ControlAM :Amplitude ModulationAMP :AmplifierANT :AntennaAPC :Automatic Phase ControlASS’Y :AssemblyAUX :Auxiliary
B B :BaseBGP :Burst Gate PulseBPF :Bandpass FilterBS :Brodcasting SatelliteBW or B/W :Black and White
C C :Capacitor, Chroma, CollectorCAN :CancelCAP :CapstanCAP.BRK :Capstan BrakeCAP.RVS :Capstan ReverseCATV :Cable TelevisionCBA :Circuit Board AssemblyCCD :Charge Coupled DeviceC.CTL :Chro Control, Capstan ControlCFG :Capstan Frequency GeneratorCHROMA :ChrominanceCNR :Chroma Noise RedutionCOMB :Combination
Comb FilterCOMP :Comparator
CompositeCompensation
CONV :ConverterC.ROT SW :Color Rotary SwitchCS :Chip SelcetC.SYNC :Composite SynchronizationCTL DIV :Control DivideCUR :CurrentCYL :Cylinder
D D :Drum, Digital, Diode, DrainD.ADJ :Drum AdjustDC :Direct CurrentD.CTL :Drum ControlDEMOD :DemodulatorDET :DetectorDEV :DeviationDHP :Double High PassDIGITRON :Digital Display TubeDL :Delay lineDOC :Drop Out CompensatorDUB :DubbingD.V SYNC :Dummy Vertical Synchronization
E E :EmitterEE :Electric to EletricEMPH :EmphasisENA :EnableENV :EnvelopeEP :Extended PlayEQ :EqualizerEXP :Expander
F F :FuseFB :Feed BackFBC :Feed Back ClampFE :Full EraseFG :Frequency GeneratorFL :FilterFM :Frequency ModulationF/R :Front/RearFS :Frequency SynthesizerFSC :Subcarrier FrequencyF/V :Frequency Voltage
G GEN :Generator
H H :High, Horizontal
I IC :Integrated CircuitIF :Intermediate FrequencyINS :Insert
L L :Low, Left, CoilLD :LEDLD VTG CTL :Loading Voltage ControlLECHA :Letter CharacterL.M :Level MeterLP :Long Play
LPF :Low Pass Filter
M MAX :MaximumMD :ModulatorMECHA.CTL :Mechanism ControlMIC :MicrophoneMIN :MinimumMIX :Mixer, MixingM.M. :Monostable, MultivibratorMMV :Mono Multi VibratorMOD :Modulation, ModulatorMODEM :Modulator-DemodulatorMPX :Multiplex
N NR :Noise Reduction
O OSC :OscillatorOSD :On Screen Display
P PB :PlaybackPCB :Printed Circuit BoardP.CTL :Power ControlPRE-AMP :PreamplifierP.F :Power FailurePG :Pulse GeneratorPLL :Phase Locked LoopPREM.DET :Premire DetectP.P :Peak-to-PeakPS :Phase ShiftPWM :Pulse Width ModulationPWR CTL :Power Control
Q Q :TransistorQH :Quasi HorizontalQSR :Quick Setting RecordQTR :Quick Timer RecordQV :Quasi Vertical
R R :Resistor, RightRE(or RC) :Remocon, ReceiverREC :RecordingREC S ‘H’ :Record Start ‘Hight’REF :ReferenceREG :Regulated, RegulatorREMOCON :Remote Control(unit)RF :Radio FrequencyR/P :Record/PlaybackRTC :Reel Time Counter
S S :SerialS.ACCEL :Slow AccelSAOP :Second Audio ProgramSC :Scart, SimulcastS.DET :Secam DetectSH :ShiftSHARP :SharpnessSIF :Sound Intermediate FrequencySLD :Side LockingS/N :Signal to Noise RatioSP :Standard PlayST :StereoSUB :Subtract, SubcarrierSW or S/W :SwitchSYNC :SynchronizationSYSCON :System Control
T T :CoilTP :Test PointTR :TransistorTRK :TrackingTRANS :TransformerTU :Tuner, Take-up
U UHF :Ultra High FrequencyUNREG :Unregulated
V V :Volt, VerticalVA :Always VoltageVCO :Voltage Controlled OscillatorVGC :Voltage Gain ControlVHF :Very High FrequencyV.H.SW :Video Head SwitchVISS :VHS Index SearchVPS :Video Program SystemVR :Variable Resistor or VolumeV-SYNC :Vertical SynchronizationVTG :VoltageVV :Voltage to VoltageVXO :Voltage X-tal Oscillator
W W :WattWHT :WhiteW/O :With out
X X-TAL :Crystal
Y Y/C :Luminance/ChrominanceYNR :Luminance Noise Reduction
Z ZD :Zener Diode
SECTION1 SUMMARYKEY TO ABBREVIATIONS
Important Safety Precautions
Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codesof the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement thefollowing precautions when a set is being serviced.
Fig.1
1. Locations requiring special caution are denoted by labels andinscriptions on the cabinet, chassis and certain parts of theproduct. When performing service, be sure to read and com-ply with these and other cautionary notices appearing in theoperation and service manuals.
2. Parts identified by the symbol and shaded ( ) parts arecritical for safety.Replace only with specified part numbers.Note: Parts in this category also include those specified to com-
ply with X-ray emission standards for products usingcathode ray tubes and those specified for compliancewith various regulations regarding spurious radiationemission.
3. Fuse replacement caution notice.Caution for continued protection against fire hazard.Replace only with same type and rated fuse(s) as specified.
4. Use specified internal wiring. Note especially:1) Wires covered with PVC tubing2) Double insulated wires3) High voltage leads
5. Use specified insulating materials for hazardous live parts.Note especially:1) Insulation Tape 3) Spacers 5) Barrier2) PVC tubing 4) Insulation sheets for transistors
6. When replacing AC primary side components (transformers,power cords, noise blocking capacitors, etc.) wrap ends ofwires securely about the terminals before soldering.
Power cord
Fig.2
10. Also check areas surrounding repaired locations.
11. Products using cathode ray tubes (CRTs)In regard to such products, the cathode ray tubes themselves,the high voltage circuits, and related circuits are specified forcompliance with recognized codes pertaining to X-ray emission.Consequently, when servicing these products, replace the cath-ode ray tubes and other parts with only the specified parts.Under no circumstances attempt to modify these circuits.Unauthorized modification can increase the high voltage valueand cause X-ray emission from the cathode ray tube.
12. Crimp type wire connectorIn such cases as when replacing the power transformer in setswhere the connections between the power cord and powertransformer primary lead wires are performed using crimp typeconnectors, if replacing the connectors is unavoidable, in or-der to prevent safety hazards, perform carefully and preciselyaccording to the following steps.
1) Connector part number : E03830-0012) Required tool : Connector crimping tool of the proper type
which will not damage insulated parts.3) Replacement procedure
(1) Remove the old connector by cutting the wires at a pointclose to the connector.Important : Do not reuse a connector (discard it).
Fig.7
cut close to connector
Fig.3
(2) Strip about 15 mm of the insulation from the ends ofthe wires. If the wires are stranded, twist the strands toavoid frayed conductors.
15 mm
Fig.4
(3) Align the lengths of the wires to be connected. Insertthe wires fully into the connector.
Connector
Metal sleeve
Fig.5
(4) As shown in Fig.6, use the crimping tool to crimp themetal sleeve at the center position. Be sure to crimp fullyto the complete closure of the tool.
1
vPrecautions during Servicing
7. Observe that wires do not contact heat producing parts(heatsinks, oxide metal film resistors, fusible resistors, etc.)
8. Check that replaced wires do not contact sharp edged orpointed parts.
9. When a power cord has been replaced, check that 10-15 kg offorce in any direction will not loosen it.
1.252.0
5.5
Crimping tool
Fig.6
(5) Check the four points noted in Fig.7.
Not easily pulled free Crimped at approx. centerof metal sleeve
Conductors extended
Wire insulation recessedmore than 4 mm
S40888-01
v Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have beenreturned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compli-ance with safety standards.
1. Insulation resistance testConfirm the specified insulation resistance or greater between power cord plug prongs andexternally exposed parts of the set (RF terminals, antenna terminals, video and audio inputand output terminals, microphone jacks, earphone jacks, etc.). See table 1 below.
2. Dielectric strength testConfirm specified dielectric strength or greater between power cord plug prongs and exposedaccessible parts of the set (RF terminals, antenna terminals, video and audio input and outputterminals, microphone jacks, earphone jacks, etc.). See table 1 below.
3. Clearance distanceWhen replacing primary circuit components, confirm specified clearance distance (d), (d’) be-tween soldered terminals, and between terminals and surrounding metallic parts. See table 1below.
4. Leakage current testConfirm specified or lower leakage current between earth ground/power cord plug prongsand externally exposed accessible parts (RF terminals, antenna terminals, video and audioinput and output terminals, microphone jacks, earphone jacks, etc.).Measuring Method : (Power ON)Insert load Z between earth ground/power cord plug prongs and externally exposed accessi-ble parts. Use an AC voltmeter to measure across both terminals of load Z. See figure 9 andfollowing table 2.
5. Grounding (Class 1 model only)Confirm specified or lower grounding impedance between earth pin in AC inlet and externally exposed accessible parts (Video in,Video out, Audio in, Audio out or Fixing screw etc.).Measuring Method:Connect milli ohm meter between earth pin in AC inlet and exposed accessible parts. See figure 10 and grounding specifications.
d'
d
ChassisPower cord,primary wire
Region
USA & Canada
Europe & Australia
Grounding Impedance (Z)
Z 0.1 ohm
Z 0.5 ohm
≤≤
AC inlet
Earth pin
Exposed accessible part
Milli ohm meter
Grounding Specifications
Fig. 10
a b
c
VExternallyexposedaccessible part
Z
Fig. 9
Fig. 8
Clearance Distance (d), (d')
d, d' 3 mm
d, d' 4 mm
d, d' 3.2 mm1 MΩ R 12 MΩ/500 V DC
Dielectric Strength
AC 1 kV 1 minute
AC 1.5 kV 1 miute
AC 1 kV 1 minute
AC Line Voltage
100 V
100 to 240 V
110 to 130 V
110 to 130 V
200 to 240 V
Japan
USA & Canada
Europe & Australia R 10 MΩ/500 V DC
Region Insulation Resistance (R)
R 1 MΩ/500 V DC≤
≤
≥ ≥
≤≤≤
≤≤≤
AC 3 kV 1 minute(Class 2)
AC 1.5 kV 1 minute(Class 1)
d 4 mmd' 8 mm (Power cord)d' 6 mm (Primary wire)
Table 1 Specifications for each region
a, b, cLeakage Current (i)AC Line Voltage
100 V
110 to 130 V
110 to 130 V
220 to 240 V
Japan
USA & Canada
i 1 mA rms Exposed accessible parts
Exposed accessible parts
Antenna earth terminals
Other terminals
i 0.5 mA rms
i 0.7 mA peaki 2 mA dc
i 0.7 mA peaki 2 mA dc
Europe & Australia
Region Load Z
≤
≤
≤≤≤≤
1 kΩ
2 kΩ
1.5 kΩ
0.15 µF
50 kΩ
Table 2 Leakage current specifications for each region
Note: These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.
2 S40888-01
1-4
• The Contents of ExaminationAs all the IC that is applied to VCR is controlled by IIC, mutual communication, if Vcc of IC is short or openwith detecting ‘Acknowledge’ data of the specific IC according to each power(5V, 5VT) µ-COM gets unable todetect ‘ACK’ data.µ-COM regards this case as abnormal one and if it can’t detect ‘ACK’ data for a certain time(3.5 sec) the sig-
nal of ‘Power Control’ and ‘Timer Control’ are switched to ‘Low’. As a result POWER Switching TR is kept fromgenerating heat and fire.
• POWER for each IC
S/ 5V POWER SECAM ICSeries 5VT POWER AVCP ICP/Y/I 5V POWER ModulatorSeries 5VT POWER AVCP IC
*Short protection off mode : DJ01 Diode in
PROPOSAL FOR APPLYING SHORT PROTECTION
IIC BUS
5VT SW POWERCONTROL
MASTER
TIMERCONTROL
5VT SW
SLAVE with 5V
SLAVE with 5V
5.3VA
Timer Control
AVCP ICTUNER
ConceptionBLOCK Diagram
5.2V 5.2VT
• IC to detect ‘ACK’ data is selected as below because IC is different in accordance to region and option
5.3VA
Power Control
Modulator
Hi-Fi IC
NICAM IC
SECAM IC
1-5
In case that defective EEPROM of PAL models is replaced, to operate these sets from the initial state MP KEYmust be repaired as well before delivering to the customer. If MP KEY isn’t repaired the setting of RF OUT channel or LANGUAGE might be different from that for cus-tormer’s country.
•MP KEY : In case of PAL VCR if holding the REC button on the front panel and the CLEAR button on theremote control handset for 5 ~ 7 seconds with power being switch all and no tapes,OK is displayed at FLD for FLD models and LED becomes on for LED CLOCK models.This is the state that initializing EEPROM is finished.(In case of PAL VCP if holding the REC button on the front panel and the MENU button on theremote control handset for 5 ~ 7 seconds with power being off and no tapes, All the LED DOTsbecome on. This is the state that initializing EEPROM is finished.)
•MP KEY's function : MP KEY sets EEPROM's data up to the initial state.
SERVICE NOTICE ON REPLACING EEPROM
TIMER
AM
REC
VCR
OK• FLD MODEL:
MP KEY “OK”
• LED CLOCK MODEL:MP KEY Switch all on a Light
• LED DOT MODEL:MP KEY Switch all on a Light
1-6
SERVICE INFORMATION FOR EEPROM IC SETTING
MODEL NAME HEX BINARYHR-J285EU 02 00 00000000
C0 00 00000000C0 00 00000000B1 00 0000000030 00 0000000048 00 00000000
HR-J290EU E2 00 00000000HR-J293EU C1 00 00000000
C8 00 00000000B1 00 0000000030 00 0000000048 00 00000000
HR-J585EU 0C 00 00000000C0 00 00000000C0 00 00000000B1 00 0000000030 00 0000000048 00 00000000
HR-J590EU/ EC 00 00000000J593EU C1 00 00000000
C8 00 00000000B1 00 0000000030 00 0000000048 00 00000000
HR-J595EK 2C 00 00000000C0 00 00000000C8 00 00000000B4 00 0000000000 00 0000000043 00 00000000
HR-J595MS 6C 00 00000000C0 00 0000000048 00 00000000B0 00 0000000062 00 0000000040 00 00000000
HR-J295MS 62 00 00000000C0 00 0000000048 00 00000000B0 00 0000000062 00 0000000040 00 00000000
HR-J295EK 02 00 00000000C0 00 00000000C8 00 00000000B4 00 0000000000 00 0000000043 00 00000000
HR-J282EU 02 00 00000000C0 00 00000000C0 00 00000000B7 00 0000000000 00 0000000050 00 00000000
MODEL NAME HEX BINARYHR-J283EU 02 00 00000000
C0 00 00000000C8 00 00000000B7 00 0000000000 00 0000000050 00 00000000
HR-J582EU 0C 00 00000000C0 00 00000000C0 00 00000000B7 00 0000000000 00 0000000050 00 00000000
HR-J583EU 0C 00 00000000C0 00 00000000C8 00 00000000B7 00 0000000000 00 0000000050 00 00000000
# Remote control Key action
• OK : Now option data write to EEPROM• MENU : Menu exit• EDIT : (Option data change from 0~F
Hexadecimal)• MOVE : (Cursor move for option data
setting)
1. Power Cord plug-in and Power SW on, then“EEPROM option data setting” screen to the leftwill be displayed.
# If not, press the “Child lock” key on the Remotecontroller to switch with “CANAL” because theVCR set has “CANAL IC” inside.
# If your VCR set has “NTSC Line Record”, switchthe VCR set to “AV” mode after inputting the LineVideo signal. If not, the Blue back screen may beshown in to screen.
2. Refer to option data in the next page and inputthe value to the “HEX” field using “EDIT” keyonly, and then press the “OK” key on the Remotecontroller.
3. Check the basic operation(Tuner/PB/CUE/REV/AV/REC mode...)
4. Initialize the EEPROM IC pressing the “REC” keyon the Front Panel and “CLEAR” key on theRemote controller at the same time.
EEPROM option code No. setting
EEPROM option code No. setting procedure
1-7
SPECIFICATIONS
GeneralPower : 200~240V, 50HzPower consumption : Approx. 12 watts(Energy Saving mode : 3 watts)Video Head system : Rotary 2heads, helical scanning system
(2HD Model)Double azimuth 4 heads, helical scanning system(4HD MONO, 4HD Hi-Fi Model)
Tape speed : 23.39 mm/sec (SP mode)11.69 mm/sec(LP mode)Tape format : Tape width 1/2” (12.7 mm high density VHS tape)Maximum recording time : 4 hours in SP mode/8 hours in LP mode (with E-240 tape)Rewind time : Approx. 150 sec. (with E-180 tape)Dimensions (W X H X D) : 360 x 94.5 x 270 mmWeight : 9.0 lbs. (4.0 kg)Operating temperature : 41°F-95°F (5°C-35°C)Operating humidity : Less than 80%Timer : 24 hours display type
VideoTelevision system : CCIR standard (625 lines, 50 fields)
PAL colour signalRecording format : PAL B/G (HR-J282EU/J283EU/J582EU/J583EU/J285EU/
J290EU/293EU/J585EU/J590EU/J593EU)PAL N (HR-J295EK/J595EK)PAL SECAM-L (HR-J295MS/J595MS)
Input level : VIDEO IN (SCART, RCA type)1.0 Vp-p, 75 ohm, unbalanced
Output level : VIDEO OUT (SCART type)1.0 Vp-p, 75 ohm, unbalanced
Signal to noise ratio : More than 43 dBm
AudioInput level : AUDIO IN (SCART type)
Scart type : -6.0dBm, more than 10kΩOutput level : AUDIO OUT (SCART, RCA type)
Scart type : -6.0dBm, less than 1kΩRCA type : -6.0 dBm, less than 1kΩ
Audio track Mono track & Hi-Fi trackAudio signal to noise ratio : Normal : More than 70 dBm(JIS A filter)Audio dynamic range : Hi-Fi audio : More than 85 dBm(JIS A filter)
• Design and specifications are subject to change without notice.
:Hi-Fi Model only
2-1
SECTION 2 CABINET & MAIN CHASSISSERVICE METHOD
Fig.2-1
Electrical Part
(1) Re-assembly Flow for service like Fig. 2-1
(2) To check and replace Electrical parts2 Re-assemble the unit according to No.1) Re-assembly Flow.3 Place the unit like Fig. 2-14 Check and replace Electrical parts.
NOTE :1 Insert Video Cassette Tape inversely like Fig. 2-1 to check and replace defective parts.2 In disassembling and reassembling, be careful not to damaged CST switch.
Timer C.B.A
Main C.B.A
Housing & DeckAssembly
Timer C.B.A
Housing & Deck Ass'y
Cassette Tape(Upside Down)
Main C.B.A(Positioned Upside Down)
2-2
EXPLODED VIEWS1. Cabinet and Main Frame Section
A46
260
452
330
323
A43
283
280
284
277
300
TU70
1(TU
NE
R)
2SC
AR
T
1SC
AR
T
452
320
452
452
A42
A49
281
250
462
462
A00
275
LED
502(
LED
501)
457
464
A
5
4
3
2
1
B C D
NOTE) Refer to “SECTION 5 REPLACEMENTPARTS LIST” in order to look for thepart number of each part.
OPTIONAL PARTS
2.Packing Accessory Section
OPTIONAL PARTS
CABLE SET ASS'Y(Optional parts)
810
BATTERY808
806
PLUG ASS'Y 2WAY(Optional parts)
812
PLUG ASS'Y 1WAY(Optional parts)
811
REMOCON900
PACKING (RF)803
PACKING (LF)803
BOX CARTON802
BAG. SOFR SHEET804
INSTRUCTION MANUAL801
SCART CABLE821
NOTE) Refer to “SECTION REPLACEMENT PARTS LISTNOTE) in order to look for the part number of each part.
2-3
3-1
NICAM
(COMPONENT SIDE)
SCART JACK
Hi-Fi
SYSTEM
AVCP
Micom
TUNER
Speak-ez SW/IC
SECAM
VPS
EEPROM
CLK IC
W501H.S/W
E2PROM
C+
SMPS
A/VW502
DISPLAY(DOT,CLK)
: Measurement point: Adjustment point
SECTION 3 ELECTRICALELECTRICAL ADJUSTMENT POINTS ARRANGEMENT
3-2
ELECTRICAL ADJUSTMENT PROCEDURES
1. Servo Adjustment1) PG Adjustment
• Test Equipment
• Adjustment And Specification
a) OSCILLOSCOPEb) PAL TEST TAPE (VHS SP)c) JIG REMOCON (AUTO PG SETTING)
MODE
PLAY
• Adjustment Procedure
a) Insert the PAL SP Test Tape and play.Note - Adjust the distance of X, pressing the Tracking(+) or Tracking(-) when the “ATR(OSD on moni-
tor)” is blink after PAL SP test Tape is inserted.
b) Press the Auto PG KEY on JIG Remocon(1’st) or Press “Play” key on set and “0” key onRemocon.(Then check the light 4 Dot LED on CLK/LED - TRK is a Initial)
c) Press the Auto PG Key on JIG Remocon again (2’nd) or press “Play” key on set and “0” key onRemocon again.(Then check the blink 4 Dot LED - At regular 0.25sec internal, Then check blink “PGwaveform” on oscilloscope(MONO Model)).
• Check the PG
a) Connect the CH1 of the oscilloscope to the H/SW and CD2 to the Video out for the VCR.
b) Trigger the mixed Video Signal of CH2 to the CH1 H/SW(W501, W502), and then check the distance (time difference), which is from the selected A(B) Head point of the H/SW(W501, W502) signal to thestarting point of the vertical synchronized signal, to 6.5H ± 0.5H (416µs, 1H=64.0µs).
• CONNECTION
V.OutH/SW(W501, W502)
6.5 ± 0.5H
MEASUREMENT POINT ADJUSTMENT POINT SPECIFICATION
V.Out
H/SW(W501,W502)
OSCILLOSCOPE
CH1 CH2
V.outH/SW(W501, W502)
3-3
ELECTRICAL ADJUSTMENT PROCEDURES
• WAVEFORM
• Attension and Referencea) The PG checking must do when RF Level is Maximum and SERVO system is Locking (MTR MODE)
b) V.H/SW Level is 2Vpp.
H/SW
CompositeVIDEO
6.5H(416us)
3-4
ELECTRICAL TROUBLESHOOTING GUIDE
1. Power Circuit(SMPS)
(1) No 5.3VA.
No 5.3VA.
Is the F101 normal?
Is the BD101 normal?
Is the R101 normal?
Does the oscillation waveform appear atthe IC101 Pin 7?
Is there DC voltage at the IC101 Pin 4?
Is there about 2.5V at the IC103 Vref ?
Is the D106 normal?
Check the Main PCB 5.3VA Line short?
Replace the F101(Use the same Fuse).
Replace the BD101.
Replace the R101.
Is Vcc(about 13~15V) permittable at theIC101 Pin 3?
Check or Replace the D103.
Replace the IC102.
Replace the IC103.
Replace the D106.
NO
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
NO
3-5
Is the D109 normal? Replace the D109.
Check 12VA Line of the Main PCB short.
YES
YES
No 12VA.
Does 5.3VA work normally? Check whether 5.3VA is out of order.
YES
NO
NO
7. Power Circuit(SMPS)
(2) No 12VA.(Capstan)
(3) No 12VA (CANAL, Buffer)
Is Voltage(about 12V) put into theQ155(C)?
Check or Replace the Q155.
YES
YES
No 12VA.
Is Vcc(about 13VA) put into the Q155(E)? Replace the Peripheral Circuitry of D160.
YES
NO
7. Power Circuit(SMPS)
(4) No 5VT(5V)
Is about 4.7V put into theQ152(Q151) Base?
Check the Q163(Q162)whether it works normally.
Check or Replace the Q152(Q151).
YES
YES
No 5VT.(5V)
Is the Q163(Q162) Base “H”?
Is 5.3VA put into the Q152(Q151)collector?
Check the µ-com Control.
YES
YES
NO
NO
3-6
3-7
2. Servo Circuit
Unstable Video in PBMode.
Does the on screen noiselevel change periodically?
Do CTL pulses appear at IC501 pin 8?
Does the CFG dividewaveform appear at IC501pin 9?
Do the CTL pulses movewhen TRK is operated?
Replace IC501.
Does the Video Envelopewaveform appear at IC501 Pin 24?
NO
YES
YES
YES
YES
YES
A.
Is the height of the CTLHead adjusted correctly?
NO
Replace IC501.
NO
Check AVCP IC.
NO
Adjust the CTL Head.
Drum Motor stopped.
Does 12V appear at PMC01 Pin 8?
Does 2.8V appear at PMD01 Pin 12?
Check Connector and Drum Motor Ass’y.
Check the Components and foil Pattern between IC501 Pin 26 and PMC01Pin 12 for shorts.
Does the Drum PWM waveformappear at IC501 Pin 107?
Check the Components and foil PatternConnected to IC501 Pin 107 PMC01Pin 12 for shorts.
Do DFG Pulses appear at IC501 Pin 104?
B.
NO
NO
NO
NO
Check Power.
Does Drum PWM appear at IC501 Pin107?
Do DFG Pulses appear at PMD01 Pin 3?
Check Drum Monitor Ass’y.
Check the Components and foil pattern between PMC01 Pin 11 and IC501Pin 104 for shorts.
Replace IC501.
YES
YES
YES
YES
YES
NO
NO
3-8
3-9
Capstan Motor Stopped.
Check Power.
Does PWM wave appear at IC501Pin 108?
Does the CFG signal appear at PMC01Pin 1?
Check Capstan Motor Ass’y.
Check Components and foil patternsbetween PMC01 Pin 7 and IC501Pin 9 for shorts.
Replace IC501.
Does 13VA appear at PMC01 Pin 2?
Does 2.8V appear at PMC01 Pin 9?
Check Connector and CapstanMotor Ass’y.
Check the Components and foil PatternsConnected between IC501 Pin 108 andPMC01 Pin 9 for shorts.
Does the CFG signal appear at IC501Pin 9?
Does Capstan PWM appear at IC501Pin 108?
Check the components and foil patternconnected between IC501 Pin 108 andPMC01 Pin 9 for shorts
C.
NO
NO
NO
NO
NOYES
YES
YES
YES
YES
YES
NO
YES
YES
YES
Does 5.3V appear at RS501.
Check the Power.
Check the Drum Motor Signal.
Do Take-up reel pulsesappear at the base ofQ514?
Replace the Take-Up ReelPhotocoupler in theDeck(RS501).
Auto stop.
Does SW30 waveformappear at IC501 Pin 105?
Do Take-up reel pulsesappear at IC501 Pin 49?
Change IC501.
A.
NO
NO
NO
NOYES
3. System & Front Panel Circuit
3-10
3-11
YES
YES
Cassette tape loading is unstable.
Is REG 14VA applied to PMC01 Pin 8?
Is High signal applied to IC501 Pin 30when inserting the CST?
Does Low signal occur form PMC01Pin 10 when inserting the CST?
Check the Deck Mechanism.
NOTE : Auto stop may also be caused by lack of lubrication,due to dried grease or oil.
Is 5.4VA applied to R544?
Check the power.
Check IC501 Pins 68, 69, 70, 71.
Check the CST SW andperipheral circuitry. Check the power.
B.
NO
NO
NOYES
NO
YES
Non working finction buttons.
Is the voltage of IC501 Pin 36, 5V?
Does(LED Ass’y) display changewhen a function button is pressed?
Replace IC501.
Replace the defective switch.
Check the power.
Check IC506 Pins 6~14, 17, Pins 20~23pulse output.
Replace IC506.
C.
YES
YESNO
NO
4. Y/C CIRCUIT
(1) No Video in EE Mode,
No Video in EE Mode
Check the Video InputJack.(Line In Jack)
Does the Video signalappear at the IC301 Pin 48?
Is 5V applied to the IC301Pins 18, 24, 42, 55, 72, 91?
Does the Video signalappear at the IC301 Pin 65?
Does the Video signalappear at the IC501 Pin 19?
Does the Video signalappear at the Emitter termi-nal of the Q307, Q308?
Check the 5.2VT, 5.4VALine. (Power Circuit)
Is I2C BUS signal applied tothe IC301 Pins 68, 69?
Check C316. (AGC)Chck the path of the signalbetween the IC301 Pin 5and IC501 Pin 17.
Replace the IC301.Does the 12VT, 5.4VAappear at the Emitter termi-nal of the Q307, Q308.
Replace the Q307, Q308.Check the 12VT, 5.4VALine. (Power Circuit)
Check the System Circuit.(Refer to ‘SYSTEM I2C BUSCHECK Trouble Shooting’)
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO NO
NO
NO
NO
3-12
3-13
3. Y/C CIRCUIT
(2) When the Y(Luminance) signal doesn’t appear on the screen in PB Mode,
Is 5.2VT, 5.4VA applied to theIC301 Pins 24, 42, 55, 72, 91?
Is the I2C Bus siganl applied to the IC301 Pins 68, 69 ?
Does the normal RF signalappear at the IC301 Pin 78?
Check the line of the 5.2VLine. (Power Circuit)
Check the System Circuit.(IC501 Pin 105)
Check the V.H.S/W level.(Check R303, R304)
Replace the IC301.
Refer to ‘SYSTEM I2C BUSCHECK Trouble Shooting’.
Is the V.H.S/W signalapplied to the IC301 Pin 70?
Is V.H.S/W “H” about 3.4Vat the IC301 Pin 70?
Clean the Drum.
Check the path of theY(Luminance) RF signal.(Check C327)
Check the path of the Y(Luminance) RF signal.(Check the C312)
Does the Y(Luminance) RFsignal appear at the IC301Pin 76?
Is the Y(Luminance) Videowaveform showed up attheIC301 Pin 43?
Replace the IC301.
NO
YES
YES
YES
YESYES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
NO
3. Y/C CIRCUIT
(3) When the C(Color) signal doesn’t appear on the screen in PB Mode,
Is 5.2VT/5.4VA applied to theIC301 Pins 24, 42, 55, 72, 91.
Is the Color Rotary signal applied to the IC301Pin 70?
Does the Color signalappear at the IC301Pin 25 ?
Check the line of the 5.2VT/5.4VA Line. (Power Circuit)
Replace the X301.
Check the Color Pass.
Check the Color RotaryCircuit. (IC501 pin 99 )
Check the Color Rotarylevel. (Check the R303)
Does the X301(4.43MHZ)oscillate?
Replace the IC301.
Does the Color signalappear at the IC301 Pin 21?
Is Color Rotary “H”about 3.4V?
Replace the IC301.
NO
YES
YES
YES
YES
NO
NO
NO NO
NO
YES
3-14
3-15
3. Y/C CIRCUIT
(4) When the Video signal doesn’t appear on the screen in REC Mode,
Is the EE signal normal?
Is 5.2VT/5.4VA applied to theIC301 Pins 24,42,55,72,91?
Does the RF signal appearat the IC301 Pin 78?
Check EE Mode.
Check the System of REC‘H’. (the IC501 Pin 47 / the D301)
Replace the IC301.
Check the line of the 5.2VT/5.4VA Line.(Power Circuit)
Check PB Mode.
Is the REC ‘H’ signal(about 4V) applied to theIC301 Pin 80?
Check the circuit of the IC301 Pins 85, 86.
Check REC LuminancePass & Color Pass.
Does PB Mdoe operatenormally?
Does the REC RF signalappear at the IC301Pins 88,89,94,95?
Check the Drum &Drum Connector
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
YES
YES
YES
5. Tuner/IF circuit
(1) No picture on the TV screen
No picture on theTV screen
Does the Video signal atthe TU701 Pin24? Check 33VT line.
Check 5VT line.
Check the liC Clocksignal of µ-com Pin 59.
Is +30VT applied toTU701 Pin 16?
Is +5VT applied toTU701 Pin 13?
Does the Clock signal appear at TU701 Pin 11?
Does the data signalappear at TU701 Pin 12?
Replace Tuner
Check the signal flowfrom TU701 Pin 24 toIC301 Pin 67.
Does Sync appear atIC501 Pin111?
Check the signal flow fromIC501 Pin19 to JK901Pin19.
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
Check the liC Data signalof µ-com Pin 60.
NO
3-16
3-17
(2) No sound (Mono Model)
No sound
Check the Vcc of IC301 Pin 18.
Check the Tuner Audio signalat IC301 Pin 13.
Check the Audio signal at IC301 Pin 11.
Check 5VT power.
Chekc the signal flow from TU701Pin21 to IC301 Pin 13.
Replace IC301.
NO
NO
NO
YES
YES
YES
Check the signal flow from IC301pin 11 to IC901 Pin 6.
YES
3-18
(3) No sound (Hi-Fi Model)
No sound
Check the Vcc of IC751 Pins 1, 19, 33.
Check the Tuner SiF signal at IC751 Pin 2.
Check the oscillator of IC751 Pins 5, 6.
Check the Audio of IC751 Pins 30, 31.
Check the Audio of IC801 Pins 2, 3.
Check the Audio of IC801 Pins 18, 19.
Check the signal flow from IC801pins 18, 19 to JK901 Pins 1, 3.
Check 5V power.
Check the Tuner Audio of TU701 Pin 21.
Replace X751.
Check the IIC Clock and Data atIC751 Pins 12, 13.
Check the signal flow from IC751Pins 30, 31 to IC801 Pins 2,3.
Check the IIC Clock and Data atIC801 Pins 42, 43.
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
3-19
Check power.
Check IC501 Pin 23.(Audio head switch 25)
Check the Vcc ofIC801.(Pins 34, 40)
Is the Head switching signal IC802 Pin 41 O.K?
Check the connection atP3D01 if good thenReplace IC801.
Check Ports of µ-COM.
Replace IC801.
Hi-Fi Playback.
No sound
Check the Hi-Fi SelectionSwitch and the Tape quality.
Is the RF Envelope atIC801 Pin 44 over 2Vp-p?
Check the Signal pathof Audio Output.
Do Audio signals appear atIC801 Pin 16(L-CH), 17(R-CH)?
Check IC801 Pin 42(Data),Pin 43(Clock).
A.
YES
NO
YES
NO
NO
NO
NO
6. Hi-Fi Circuit (Hi-Fi Model)
YES
YES
YES
YES
YES
Hi-Fi REC.
It is impossible to record and playbackHi-Fi Audio signal.
Check Vcc of IC801. (Pins 34,40)
Check Power.
Check ports of µ-COM.
Check Audio input signal of IC801Pins 2, 3(TU.A.), 6, 7(Scart 1)
Replace IC801.
B.
Check IC801 Pin 42(Data),Pin 43(CLOCK).
Do Audio signals appear at IC801Pins 16, 17?
YES
YES
YES
Do FM Audio signals appear at IC801Pin 36?
Check the Contact Points of DrumConnector if good then Replace the Drum.
YES
YESNO
NO
NO
NO
3-20
• Top View...................................................4-1• Bottom View ............................................4-1
1. Drum Assembly .........................................4-22. Plate Top ...................................................4-43. Holder Assembly CST...............................4-44. Opener Door .............................................4-45. Bracket Assembly L/D Motor.....................4-46. Gear Assembly Rack F/L ..........................4-47. Arm Assembly F/L .....................................4-48. Lever Assembly S/W.................................4-49. Arm Assembly Cleaner..............................4-510.Head F/E ...................................................4-511. Base Assembly A/C Head .........................4-512.Brake Assembly RS ..................................4-613.Brake Assembly T .....................................4-614.Arm Assembly Tension..............................4-615.Reel S / Reel T..........................................4-616.Base Assembly P4 ....................................4-717.Opener Lid ................................................4-718.Arm Assembly Pinch .................................4-719.Lever T/up / Arm T/up ...............................4-720.Belt Capstan/Motor Capstan.....................4-821.Lever F/R ..................................................4-822.Clutch assembly D35 ................................4-823.Bracket Assembly Capstan .......................4-824.Gear Drive/Gear Cam ...............................4-925.Gear Sector...............................................4-926.Plate Slider................................................4-927.Lever Tension............................................4-928.Lever Spring..............................................4-929.Gear Assembly P2/
Gear Assembly P3 ..................................4-1030.Base Assembly P2/
Base Assembly P3 ..................................4-1031.Base Loading ..........................................4-1132.Base Tension ...........................................4-1133.Arm Assembly Idler Jog ..........................4-11
• Tools and Fixtures for Service.............4-121. Mechanism and Mode Switch Alignment
Check ......................................................4-132. Deck Preparation for Adjustment ............4-143. Checking Torque .....................................4-144. Guide Roller Height Adjustment..............4-15
4-1. Preliminary Adjustment ....................4-154-2. Precise Adjustment ..........................4-15
5. Audio/Control (A/C) Head Adjustment ....4-165-1. Preliminary Adjustment ....................4-165-2. Confirmation of Tape Path between
Pinch Roller and Take-up Guide .....4-175-3. Precise Adjustment(Azimuth Adjustment)
.........................................................4-176. X-Value Adjustment .................................4-177. Adjustment after Replacing Drum Assembly
(Video Heads) .........................................4-188. Check the Tape Travel after Reassembling
Deck Mechanism.....................................4-188-1. Checking Audio and RF Locking Time
during Playback after CUE or REV.........................................................4-18
8-2. Checking Tape Curling or Jamming.........................................................4-18
1. Check before starting Repairs ................4-192. Required Maintenance ............................4-203. Scheduled Maintenance..........................4-204. Supplies Required for Inspection and
Maintenance............................................4-205. Maintenance Procedure ..........................4-20
5-1. Cleaning...........................................4-205-2. Greasing ..........................................4-21
1. Deck Mechanism.....................................4-232. Front Loading Mechanism.......................4-26
1. Front Loading Mechanism Section .........4-282. Moving Mechanism Section (1)...............4-293. Moving Mechanism Section (2)...............4-30
SECTION 4 MECHANISM
DECK MECHANISM PARTSLOCATIONS
DECK MECHANISM ADJUSTMENT
MAIN TENANCE/INSPECTIONPROCEDURE
EXPLODED VIEWS
CONTENTS
DECK MECHANISMDISASSEMBLY
MECHANISM TROUBLESHOOTINGGUIDE
DECK MECHANISM PARTS LOCATIONS
4-1
4
6
3
2
7
9
5
11
18
16
1917
19
12
13
15
10
1
31
14
8
15
33
• Top View
• Bottom View
20
24
23
20
24
22
21
29
30
29
30
253227
2628
NOTE : When reassembly perform theprocedure in the reverse order.
1 Drum Assembly 3 Screw A-1 T
2 Plate Top 2 Hook A-2 T
2 3 Holder Assembly CST Chassis Hole A-2 T
2 4 Opener Door Chassis Hole A-2 T
5 Bracket Assembly 3 Hook A-2 T
L/D Motor
2,3,4 6 Gear Assembly Rack F/L 1 Hook, Chassis Hole A-2 T
2,3,4,6 7 Arm Assembly F/L Chassis Hole A-2 T
8 Lever Assembly S/W 1 Hook A-2 T
9 Arm Assembly Cleaner Chassis Embossing A-3 T
10 Head F/E Chassis Embossing A-3 T
11 Base Assembly A/C Head 1 Screw A-3 T
2,3 12 Brake Assembly RS 1 Hook A-4 T
2,3 13 Brake Assembly T 1 Hook A-4 T
2,3 14 Arm Assembly Tension 2 Hook A-4 T
2,3,12,13, 15 Reel S/Reel T A-4 T
14
16 Base Assembly P4 Chassis Embossing A-5 T
17 Opener Lid Chassis Embossing A-5 T
17 18 Arm Assembly Pinch Shaft A-5 T
17 19 Lever T/Up / Arm T/Up 1 Hook A-5 T
17,18 20 Belt Capstan/Motor Capstan 3 Screw A-6 B
21 Lever F/R Locking Tab A-6 B
20, 21 22 Clutch Assembly D35 Washer A-6 B
23 Break Assembly Capstan Locking Tab A-6 B
24 Gear Drive/Gear Cam Washer/Hook A-7 B
25 Gear Sector 1 Hook A-7 B
20,21,23, 26 Plate Slider Shaft Guide A-7 B
24,25
20,21,23, 27 Lever Tension 1 Hook A-7 B
24,25,26
2,3,14,20, 28 Lever Spring Locking Tab A7 B
21,25,23,
24,26
25 29 Gear Assembly P2/Gear Assembly P3 Boss A-8 B
2,3,14,25, 30 Base Assembly P2/Base Assembly P3 Chassis Slot A-8 B
29
2,3,14,25, 31 Base Loading 1 Screw A-9 T
29
2,3,14 32 Base Tension Chassis Embossing A-9 B
2,3,20,21, 33 Arm Assembly Idler Locking Tab A-9 T
22
StartingNo.
PracedurePart Fixing Type Fig-
ureVi-ew
1) When reassembling, confirm Mechanism and ModeSwitch Alignment Position (Pefer to Page 4-14)
2) When disassembling, the Parts for Starting No. Shouldbe removed first.
R: Top, B:Bottom
4-2
DECK MECHANISM DISASSEMBLY
(S3)
(S2)
(S2)
(S3)
(A)
Stator
Carbon Brush
Drum Motor
Rotor
Drum Sub Assembly
Drum FPC
(S1)
(S1)
(S1)
Holder FPC
H1
H2
1. Drum Assembly (Fig. A-1-1)1) Unplug the Drum FPC Connector.2) Remove three Screws(S1) on bottom side and separate
the Drum assembly.3) Unhook (H1), (H2) and separate the Holder FPC and
Cap FPC.1-1. Drum Motor1) Remove two Screws(S2) and disassemble the Stator of
the Drum Motor.(2) Remove two Screws(S3) and separate the Rotor of the
Drum Motor from the Drum Sub assembly.
When reassembling, confirm (A) portion of the Drum Subassembly whether the Carbon Brush is in there or not.
Fig. A-1
NOTE
(Fig. B-1)
Holder FPC
Drum FPC
Cap FPC
Figure in the opposite direction
DECK MECHANISM DISASSEMBLY
4-3
(B)
(E)
(C1)
(C)
Plate Top
Arm Assembly F/L
Spring Lever S/W
Gear Assembly Rack F/L
Chassis
Opener Door
Brackert Assembly L/D Motor
Holder Assembly CST
(B')
(C')(D) (E')
(H6)
(A) (B)
Lever Assembly S/W
(H8)
Fig. A-2
(Fig. A-2-1)
(Fig. A-2-2)
(Fig. A-2-6)
(Fig. A-2-7)
(Fig. A-2-5)
(Fig. A-2-3)
(Fig. A-2-4)
4-4
DECK MECHANISM DISASSEMBLY
2. Plate Top (Fig. A-2-1)1) Pull the (B) portion of the Plate Top back in direction of
arrow and separate the right side of it.2) pull the (B’) portion of the Plate Top back in direction of
arrow and separate the left side of it.(Used tools : (-) type Drive, anything tool with sharppoint or flat point.)
(1) When reassembling, push the Plate Top after alignmentthe two position(C), (C’) as Fig.
3. Holder Assembly CST (Fig.A-2-2) 1) Move the Holder assembly CST in direction of arrow and
separate the left side of it first through the (D) position ofthe Chassis.
2) Disassemble the right side of the Holder assembly CSTfrom each guided hole of the Chassis.
When reassembling, insert the (E) part of the Holder assem-bly CST in the (E’) hole of the Chassisfirst and assemble the left side of it.
4. Opener Door (Figure. A-2-3) 1) Turn the Opener Door clockwise and remove it through
the guide hole of the chassis.
5. Bracket assembly L/D Motor(Fig. A-2-4)1) Unplug the Connector(C1).
2) Unhook three Hooks(H3,H4,H5) on bottom side of theChassis, lift up the Bracket assembly L/M and disassem-ble the Bracket assembly L/D Motor.
6. Gear Assembly Rack F/L (Fig. A-2-5)1) Move the Gear Assembly Rack F/L in direction of
arrow(A) and unhook the Hook(H6) pulling back in front.2) Separate the Rear Rack F/L in direction of arrow(B).
When reassembling, align the Gear part of the GearAssembly Rack F/L with the Gear Drive as below Fig.
7. Arm assembly F/L (Fig. A-2-6)1) Move the Arm assembly F/L in direction of arrow and
separate the left side of it first.2) Disassemble the Arm assembly F/L from each guided
Hole of the Chassis.
8. Lever assembly S/W(Fig. A-2-7)1) Hook the Spring Lever S/W on the Hook(H7) first as
below Fig.2) Unhook the Hook(H8) in the left side of the Chassis and
move the Lever assembly S/W.
(B')
(C')
(C)
(B)
(D)
Holder assembly CST Chassis
Gear Rack F/L
Gear Drive
(H8)
(H7)
Chassis
Spring Lever S/W
NOTE
NOTE
(H3)
(H4)
(H5)
Bracket assembly L/M
NOTE
DECK MECHANISM DISASSEMBLY
4-5
9. Arm assembly Cleaner (Fig. A-3-1)1) Breakaway the (A) portion as Fig. A-3-1 from the
Embossing of the Chassis, turn the Arm assemblyCleaner to clockwise direction and lift it up.
10. Head F/E (Fig. A-3-2)1) Breakaway the (A) portion of the Head F/E from the
Embossing of the Chassis, turn it to counterclockwisedirection and lift it up.
11. Base assembly A/C Head (Fig. A-3-3)1) Remove the Screw(S4) and lift the Base assembly A/C
Head up.
(A)
Arm AssemblyCleaner
Base Assembly A/C Head
(S4)
Head F/E
(A)
Chassis
Fig. A-3
(Fig. A-3-1)
*(Fig. A-3-3)
(Fig. A-3-2)
4-6
DECK MECHANISM DISASSEMBLY
Brake Assembly T
Spring TB
(H9)
Reel T
Brake Assembly RS
Spring RS
Arm Assembly Tension
Spring Tension
Reel S
Base Tension
(H11)
(H12)
Chassis
(H10)
Fig. A-4
12. Brake assembly T (Fig. A-4-1)1) Unhook the Spring TB from the Hook(H9) of the Chassis.2) Lift the Brake assembly T up.
13. Brake assembly RS (Fig. A-4-2)1) Unhook the Spring RS from the Hook(H10) of the
Chassis..2) Lift the Brake assembly T up.
14. Arm assembly Tension (Fig. A-4-3)1) Unhook the Spring Tension from the Hook(H11) of the
Arm assembly tension.2) Unhook the Hook(H12) of the Base Tension and lift the
Arm assembly Tension up.
Difference for Springs
15. Reel S / Reel T (Fig. A-4-4)1) Difference for Reel S / Reel T
Spring TBSpring RSSpring Tension
(Difference for Springs)
Color (Black)
Reel S Reel T
NOTE
(Fig. A-4-1)
(Fig. A-4-3)
(Fig. A-4-4)(Fig. A-4-4)
(Fig. A-4-2)
DECK MECHANISM DISASSEMBLY
4-7
Opener Lid
ArmAssembly
Pinch
Base Assembly P4
Arm T/up
Lever T/up
(A)
(B)
(C)
(C)
(H13)
(B)
(H13)
Chassis
Fig. A-5
16. Base assembly P4 (Fig. A-5-1)1) Breakaway the (A) portion of the Base assembly P4 from
the Embossing of the Chassis.2) Turn the Base assembly P4 to counterclockwise direction
and lift it up.
17. Opener Lid (Fig. A-5-2)1) Breakaway the (B) portion of the Opener Lid from the
Embossing of the Chassis.2) Turn the Opener Lid to clockwise direction and lift it up.
18. Arm assembly Pinch (Fig. A-5-3)1) Lift the Arm assembly Pinch up.
19. Lever T/up (Fig. A-5-4)/Arm T/up (Fig. A-5-5)
1) Unhook the Hook(H13) of the bottom Chassis and lift theLever T/up up.
2) Lift the Arm T/up up.
When reassembling, confirm the (C) portion of the Armassembly Pinch is inserted to the Chassis Holecorrectly as Fig.
Place the Mechanism face down, or up side down.
NOTE
(Fig. A-5-2)
(Fig. A-5-1)
(Fig. A-5-3)
(Fig. A-5-5)
(Fig. A-5-4)
4-8
DECK MECHANISM DISASSEMBLY
Chassis
(S5)
Belt Capstan
Motor Capstan
Washer(W1)
Lever F/R
Clutch Assembly D35
Brake Assembly Capstan(L1)
(L2)
(L1)
Fig. A-6
20. Belt Capstan (Fig. A-6-1)/Motor Capstan (Fig. A-6-2)
1) Remove the Belt Capstan.2) Remove the three Screws(S5) on bottom Chassis and lift
the Motor Capstan up.
21. Lever F/R (Fig. A-6-3)1) Unlock the Locking Tab(L1) as Fig. A-6-3 and lift the
Lever F/R up.
22. Clutch assembly D35 (Fig. A-6-4)1) Remove the Washer(W1) and lift the Clutch assembly
D35 up.
23. Brake assembly Capstan(Fig. A-6-5)
1) Pull the Locking Tab(L2) back in direction of arrow and liftit up.
(Fig. A-6-1)
(Fig. A-6-2)
(Fig. A-6-3)
(Fig. A-6-5)
(Fig. A-6-4)
DECK MECHANISM DISASSEMBLY
4-9
Gear Drive
Washer (W2)
Gear Cam
Plate Slider
Lever Tension
Lever spring
Base Loading
Gear Sector
(L3)
(H15)
(H16)
(H14)
(A)
Chassis
Gear Drive Hole(C)
Gear Cam Hole(B)
Gear Drive Hole(A)
Fig. A-7
24. Gear Drive (Fig. A-7-1)/Gear Cam (Fig. A-7-2)
1) Remove the Washer(W2) and lift the Gear Drive up.2) Unhook the Hook(H14) of the Gear Cam and lift the Gear
Cam up.
When reassembling, align the Gear Drive Hole(A) and theGear Cam Hole(B) in a straight line after the Gear DriveHole(C) is aligned with the Chassis Hole as Fig.
25. Gear Sector (Fig. A-7-3)
1) Unhook the Hook(H15) of the Base Loading on bottomChassis and lift the Gear Sector up.
26. Plate Slider (Fig. A-7-4)1) Just lift the Plate Slider up.
27. Lever Tension (Fig. A-7-5)1) Unhook the (A) portion of the Lever Tension from the
Hook(H16) of the Chassis.2) Turn the Lever Tension to counterclockwise direction and
lift it up.
28. Lever Spring (Fig. A-7-6)1) Unlock the Locking Tab(L3) of the bottom Chassis and lift
the Lever Spring up.
(Fig. A-7-4)
(Fig. A-7-5)
(Fig. A-7-6)
(Fig. A-7-1)
(Fig. A-7-2)
(Fig. A-7-3)
NOTE
4-10
DECK MECHANISM DISASSEMBLY
Gear Assembly P3
Gear Assembly P2
Base Assembly P2
Base Assembly P3
(A)(B)
Chassis
Gear assembly P2 Hole
Gear sector Hole(A)
Plate slider Hole(B)
Lever spring Boss
Gear assembly P3 Hole
Fig. A-8
29. Gear assembly P2 (Fig. A-8-1)/Gear assembly P3 (Fig. A-8-2)/
1) Just lift the Gear assembly P2 up.2) Just lift the Gear assembly P3 up.
When reassembling, align the two Holes of the Gear assem-bly P2 and P3 in a straight line after confirmation whether theGear Sector Hole(A) and the Plate Slider Hole(B) are alignedor not as Fig.
30. Base assembly P2 (Fig. A-8-3)/Base assembly P3 (Fig. A-8-4)
1) Move the Base assembly P2 in direction of arrow(A)along the Guided Hole of the Chassis and disassemble iton bottom side.
2) Move the Base assembly P3 in direction of arrow(B)along the Guided Hole of the Chassis and disassemble iton bottom side.
Place the Mechanism face down, or return to originalposition.
NOTE
(Fig. A-8-1)
(Fig. A-8-2)
(Fig. A-8-3)
(Fig. A-8-4)
DECK MECHANISM DISASSEMBLY
4-11
(A)
(B) (C)
(S7)
Arm Assembly Idler JogBase Loading
Base Tension
Chassis(D)
Fig. A-9
31. Base Loading (Fig. A-9-1)1) Remove the Screw(S7).2) Lift the Base Loading up.
32. Base Tension (Fig. A-9-2)1) Breakaway the (A) portion of the Base Tension from the
Embossing of the Chassis.2) Turn the Base Tension to counterclockwise direction and
lift it up.
33. Arm assembly Idler (Fig. A-9-3)1) Make narrower the two parts, (A) and (B), as Fig. A-9-3.2) Lift the Arm assembly Idler up.
When disassembling, be careful not to be caught the (D) partby the Chassis as Fig.
NOTE
(Fig. A-9-1)(Fig. A-9-2)
(Fig. A-9-3)
DECK MECHANISM ADJUSTMENT
4-12
• Tools and Fixfures for Service
1. Cassette Torque meter1. PUJ428811.
4. Post height adjusting driver(Roller driver)PTU94002
2. Alignment tapeMHPE
3. Torque gauge3. PUJ48075-23.
SRKVIDEOCASSETTETORQUEMETERVHT-303
SR
K
- VH T- S
SRK- V HT- T
300250
200150
500
300250
200
150
500
100
DECK MECHANISM ADJUSTMENT
4-13
Purpose:To determine if the Mechanism is in the correct position, when a Tape is ejected.
1.Mechanism Alignment Position Check
1) Turn the Power S/W on and eject the Cassette by press-ing the Eject Button.
2) Remove the Top Cover and Plate Assembly Top, visual-ly check if the Gear Cam Hole is aligned with theChassis Hole as below Fig. C-2.
3) IF not, rotate the Shaft of the Loading Motor to eitherClockwise or Counterclockwise until the Alignment isas below Fig. C-2.
4) Remove the Screw which fixes the Deck Mechanism andMain Frame and confirm if the Gear Cam is aligned withthe Gear Drive as below Fig. C-1(A).
5) Confirm if the Mode S/W on the Main P.C.Board isaligned as below Fig. C-1(B).
6) Remount the Deck Mechanism on the Main P.C.Boardand check each operation.
Gear Cam
Gear Drive
(C)
Mode S/W
(B)
L/D Motor Assembly
Gear Cam
Chassis Hole Gear Cam Hole Gear Cam Hole
(A)(B)(A')
(B')
Test Equipment/ Fixture
• Blank tape
Test Conditions (MechanismCondition)
• Eject Mode (with Cassette ejected)
Check Point
• Mechanism and Mode Switch Position
Fig. C-1
Fig. C-2
CHECK DIAGRAM
BOTTOM VIEW
TOP VIEW
Gear Cam (o) and Gear Drive ( o) groove alignment
4-14
DECK MECHANISM ADJUSTMENT
Purpose: To insure smooth Transport of the Tape during each Mode of Operation.If the Tape Transport is abnormal, then check the Torque as indicated by the chart below.
2. Preparation for Adjustment (To set theDeck Mechanism to the Loading statewithout inserting a Cassette Tape).
1) Unplug the Power Cord from the AC Outlet.2) Disassemble the Top Cover and Plate Assembly Top.3) Plug the Power Cord into the AC Outlet.4) Turn the Power S/W on and push the Lever Stopper of
the Holder Assembly CST to the back for Loading the
Cassette without Tape.Cover the Holes of the End Sensors at the both sides ofthe Bracket Side(L) and Bracket Assembly Door to pre-vent a light leak.Then The Deck Mechanism drives to the Stop Mode.In this case, The Deck Mechanism can accept inputs ofeach mode, however the Rewind and Review Operationcan not be performed for more than a few secondsbecause the Take-up Reel Table is in the Stop State
and can not be detected the Reel Pulses.3. Checking Torque
The Values are measured by using a Torque Gauge andTorque Gauge Adaptor with the Torque Gauge affixed.
The Torque reading to measure occurs when the Tapeabruptly changes direction from Fast Forward of RewindMode, when quick bracking is applied to both Reels.
SRKVIDEOCASSETTETORQUEMETERVHT-303
SR
K
- VH T- S
SRK- V HT- T
300250
200150
500
300250
200
150
500
100
Test Equipment/ Fixture
• Torque Gauge(600g/cm ATG)• Torque Gauge Adaptor• Cassette Torque Meter
Checking Method
• Perform each Deck Mechanism Mode withoutinserting a Cassette Tape(Refer to above No.2Preparation for Adjustment).
• Read the Measurement of the Take-up or SupplyReels on the Cassette Torque Meter(Fig. C-3-2).
• Attach the Torque Gauge Adaptor to the TorqueGauge and then read the Value of it(Fig. C-3-1).
NOTE:
Fig. C-3-2 Fig. C-3-1
Torque Gauge
Torque GaugeAdaptor
Reel Table
Item
Fast Forward Torque
Rewind Torque
Play Take-Up Torque
Review Torque
Mode
Fast Forward
Rewind
Play
Review
Test Equipment
Cassette Torque Gauge
Cassette Torque Gauge
Cassette Torque Meter
Cassette Torque Meter
Measurement Reel
Take-Up Reel
Supply Reel
Take-Up Reel
Supply Reel
Measurement Values
More than 400g/cm
More than 400g/cm
40~100g/cm
120~210g/cm
Test Conditions(Mechanism Condition)
• Play (FF) or Review (REW) Mode
NOTE:
• Cassette Torque Meter • Torque Gauge
DECK MECHANISM ADJUSTMENT
4-15
4.Guide Roller Height Adjustment
Adjustment Procedure
1) Confirm if the Tape runs along the Tape Guide Line of theLower Drum.
2) If the Tape runs the Bottom of the Guide Line, turn the GuideRoller Height Adjustment Screw to Clockwise direction.
3) If it runs the Top, turn to Counterclockwise direction.4) Adjust the Height of the Guide Roller to be guided to the
Guide Line of the Lower Drum from the Starting and EndingPoint of the Drum.
Purpose: To regulate the Height of the Tape so that the Bottom of the Tape runs along theTape Guide Line on the Lower Drum.
Test Equipment/ Fixture
• Post Height Adjusting Driver
Test Conditions (Mechanism Condition)
• Play or Review Mode
Adjustment Point
• Guide Roller Height Adjustmentscrews on the Supply and Take-UpGuide Rollers.
Fig. C-4-1
Upper Flange
Guide RollerRetaining Screw
Guide Roller Height Adjustment screw
ADJUSTMENT DIAGRAM
Test Equipment/Fixture
• Oscilloscope• Alignment Tape• Post Height Adjusting
Driver
Test Equipment Connection Points
• CH-1:PB RF Envelope• CH-2:NTSC: SW 30Hz
PAL: SW 25Hz• Head Switching Output
Point• RF Envelope Output
Point
Test Conditions VCR(VCP) State
• Play an Alignment Tape
Adjustment Point
• Guide Roller HeightAdjustment Screws
Fig. C-4-2
Fig. C-4-3
P3 POSTADJUSTMENT
P2 POSTADJUSTMENT
Turn the Roller Guide HeightAdjustment Screw slightlyto flatten the waveform.
Tracking control at center
RF ENVELOPE OUTPUT TEST POINT
OSCILLOSCOPE
HEAD SWITCHING OUTPUT TESTPOINT
Turn(Move) the trackingcontrol to both directions
4-1. Preliminary Adjustment
4-2. Precise Adjustment
Adjustment Procedure
1) Play an Alignment Tape after connecting the Probe of theOscilloscope to the RF Envelope Output Test Point andHead Switching Output Test Point.
2) Tracking Control(in PB Mode) : Center Position(Whenthis Adjustment is performed after the Drum Assemblyhas been replaced, set the Tracking Control so that theRF Output is Maximum).
3) Height Adjustment Screw : Flatten the RF Waveform.(Fig. C-4-2)
4) Turn(Move) the Tracking Control(in PB Mode)Clockwise and Counterclockwise.(Fig. C-4-3)
5) Check that any Drop of RF Output is uniform at theStart and End of the Waveform.
If the adjustment is excessive or insufficient the tape will jam or fold.
NOTE
Waveform Diagrams
Connection Diagram
4-16
DECK MECHANISM ADJUSTMENT
5. Audio/Control (A/C) Head Adjustment
10.9
Purpose: To insure that the Tape passes accurately over the Audio and Control Tracks inexact Alignment in both the Record and Playback Modes.
Test Equipment/ Fixture
• Blank Tape• Screw Driver(+) Type 5mm • Play the blank tape
Test Conditions (Mechanism Condition) Adjustment Point
• Tilt Adjustment Screw(C)• Height Adjustment Screw(B)• Azimuth Adjustment Screw(A)
Fig. C-5-1
A/C Head Base
Fig. C-5-2
Height AdjustmentScrew(B)
Tilt AdjustmentScrew(C)
Azimuth AdjustmentScrew(A)
X-Value AdjustmentHole
Fixed Screw
Fig. C-5-3
A/C Head Tape
Tape
0.2~0.25mm
P4
5-1. Preliminary Adjustment (Height and Tilt Adjustment)Perform the Preliminary Adjustment, when there is no Audio Output Signal with the Alignment Tape.
1) Initially adjust the Base Assembly A/C Head as shownFig. C-5-1 by using the Height Adjustment Screw(B).
2) Play a Blank Tape and observe if the Tape passes accu-rately over the A/C Head without Tape Curling or Folding.
3) If Folding or Curling is occured then adjust the TiltAdjustment Screw(C) while the Tape is running to resem-ble Fig. C-5-3.
4) Reconfirm the Tape Path after Playback about 4~5 sec-onds.
Ideal A/C head height occurs, when the tape runsbetween 0.2~0.25mm above the bottom edge of the A/Chead core.
NOTE
Adjustment Procedure/Diagrams
A/C Head Assembly
DECK MECHANISM ADJUSTMENT
4-17
Purpose: To obtain compatibility with other VCR(VCP) Models.
5-2. Confirm that the Tape passes smoothlybetween the Take-up Guide and PinchRoller(using a Mirror or the naked eye).
1) After completing Step 5-1.(Preliminary Adjustment),check that the Tape passes around the Take-up Guideand Pinch Roller without Folding or Curling at the Top orBottom.(1) If Folding or Curling is observed at the Bottom of
the Take-up Guide then slowly turn the Tilt Adjustment Screw(C) in the Clockwise direction.
(2) If Folding or Curling is observed at the Top of it then
slowly turn the Tilt Adjustment Screw(C) in theCounterclockwise direction.
Check the RF Envelope after adjusting the A/C Head, ifthe RF Waveform differs from Fig. C-5-4, performsPrecise Adjustment to flat the RF Waveform.
Test Equipment/ Fixture
• Oscilloscope• Alignment Tape(SP)• Screw Driver(+) Type 5mm
Connection Point
• Audio output jack
Test Conditions(Mechanism Condition)
• Play an Alignment Tape6KHz Section
Adjustment Point
• Azimuth Adjustment Screw(A)• Height Adjustment Screw(B)
1) Connect the Probe of the Oscilloscope to Audio OutputJack.
2) Alternately adjust the Azimuth Adjustment Screw(A) andthe Tilt Adjustment Screw(C) for Maximum Output of the6Khz segment.
Adjustment Procedure
5-3. Precise Adjustment (Azimuth adjustment)
6. X-Value Adjustment
Fig. C-5-4
6KHZ
• Oscilloscope• Alignment tape(SP only)• Screw Driver(+) Type 5mm
• CH-1: PB RF Envelope• CH-2: NTSC: SW 30Hz
PAL: SW 25Hz• Head Switching Output
Test Point• RF Envelope Output Test
Point
Test Conditions(Mechanism Condition)
• Play an Alignment Tape
Adjustment PointConnection PointTest Equipment/ Fixture
Adjustment Procedure
1) Release the Automatic Tracking to run long enough forTracking to complete it’s Cycle.
2) Loosen the Fixed Mounting Screw and move the BaseAssembly A/C Head in the direction as shown in theDiagram to find the center of the peak that allows for themaximum Waveform Envelope.This method should allow the 31um Head to be centrallylocated over the 58um Tape Track.
3) Tighten the Base Assembly A/C Head mounting Screw.
A:Maximum
Left
Right
Groove at theBase A/C
Height Adjustment Screw(B)
Tilt Adjustment Screw(C)Azimuth AdjustmentScrew(A)
X-Value Adjustment Hole
Fixed Screw
RF ENVELOPE OUTPUT TEST POINT
OSCILLOSCOPE
HEAD SWITCHING OUTPUT TEST POINT
Connection Diagram
Adjustment Diagram
NOTE:
CH-1 CH-2
4-18
DECK MECHANISM ADJUSTMENT
Purpose: To correct for shift in the Roller Guide and X value after replacing the Drum.
8-2.Check for tape curling or jamming
Test Equipment/ Fixture
• T-160 Tape• T-120 Tape
Specification
• Be sure there is no tape jamming or curling atthe begining, middle or end of the tape.
VCR(VCP) State
• Run the CUE, REV play mode at thebeginning and the end of the tape.
Test Conditions (Mechanism Condition)
1) Confirm that the tape runs smoothly around the rollerguides, drum and A/C head assemblies while abruptlychanging operating modes from Play to CUE or REV.This is to be checked at the begining, middle and endsections of the cassette.
2) Confirm that the tape passes over the A/C head assem-bly as indicated by proper audio reproduction and prop-er tape counter performance.
Checking Procedure
7. Adjustment after Replacing Drum Assembly (Video Heads)
Test Equipment/ Fixture
• Oscilloscope• Alignment tapes• Blank Tape• Post Height Adjusting Driver• Screw Driver(+) Type 5mm
Connection Point
• CH-1: PB RF Envelope• CH-2: NTSC: SW 30Hz
PAL: SW 25Hz• Head Switching OutputTest Point
• RF Envelope Output Test Point
Test Conditions(Mechanism Condition)
• Play the blank tape• Play an alignment tape
Adjustment Points
• Guide Roller PreciseAdjustment
• Switching Point• Tracking Preset• X-Value
Checking/Adjustment ProcedurePlay a blank tape and check for tape curling or creasing aroundthe roller guide. If there is a problem then follow the procedure4. "Guide Roller Height" and 5. "Audio Control(A/C) HeadAdjustment".
RF ENVELOPE OUTPUT TEST POINT
OSCILLOSCOPE
HEAD SWITCHING OUTPUT TESTPOINT
Connection Diagram
Waveform
V1/V MAX <= 0.7
V2/V MAX 0.8RF ENVELOPE OUTPUT
Fig. C-7
8. Check the Tape Travel after Reassembling Deck Assembly.
8-1.Check Audio and RF Locking Time during playback and after CUE or REV (FF/REW)
Test Equipment/ Fixture
• Oscilloscope• Alignment tapes(with 6H
3kHz Color Bar Signal)• Stop Watch
Specification
• RF Locking Time: Less than 5sec.
• Audio Locking Time:Less than 10sec
Test EquipmentConnection Points
• CH-1: PB RF Envelope• CH-2: Audio Output• RF Envelope Output Point• Audio Output Jack
Test Conditions(Mechanism Condition)
• Play an alignment tape(with 6H 3kHz Color Bar Signal)
Checking Procedure
Play an alignment tape then change the operating mode toCUE or REV and confirm if the unit meets the above listedspecifications.
1) CUE is fast forward mode (FF)2) REV is the rewind mode (REW)3) Referenced to the Play mode
NOTES:
V1 V V2
CH1 CH2
Connection Points
<=
MAINTENANCE/INSPECTION PROCEDURE
4-19
(3) F/E Head
(5) Drum Assembly(Video Head)
(4) BaseAssembly P2
(2) Tension Post
(1) Supply Reel
(6) Base Assembly P3
The following faults can be remedied by cleaning and oil-ing. Check the needed lubrication and the conditions ofcleanliness in the unit.Check with the customer to find out how often the unit isused, and then determine that the unit is ready for inspec-tion and maintenance. Check the following parts.
1 Check before starting repairs
Phenomenon InspectionReplace-ment
Color beats Dirt on full-erase head o
Poor S/N, no color Dirt on video head
Vertical orHorizontal jitter
Dirt on Audio/control head
Dirt on pinch roller
If locations marked with o do not operate normally aftercleaning, check for wear and replace.See the EXPLODED VIEWS at the end of this manual aswell as the above illustrations See the Greasing (Page 4-22)for the sections to be lubricated and greased.
NOTE
o
o
o
o
Dirt on video headDirt on tape transport system
Low volume,Sound distorted
Tape does not run.Tape is slack
oIn Review andUnloading (off mode),the Tape is rolled uploosely.
Clutch Assembly D33KTorque reduced
Cleaning Drum andtransport system Fig. C-9-3
(7) A/C Head
(8) P4 Post
(10) Pinch Roller
(11) Take-up Guide Post
(9) Capstan Shaft
(12) Take-up Reel
* No. (1)~(13) Indicates the Tape Path to be traveled from Supply Reel to Take-up Reel.
Fig. C-9-1 Top VIEW
Fig. C-9-2 BOTTOM VIEW
F/E Head
Video Head
A/C Head
Pinch Roller
Belt Capston
ClutchAssembly D33K
Fig. C-9-3 Tape Transport System
MAINTENANCE/INSPECTION PROCEDURE
4-20
The recording density of a VCR(VCP) is much higher thanthat of an audio tape recorder. VCR(VCP) components mustbe very precise, at tolerances of 1/1000mm, to ensure com-patiblity with other VCRs. If any of these components areworn or dirty, the symptoms will be the same as if the part isdefective. To ensure a good picture, periodic inspection andmaintenance, including replacement of worn out parts andlubrication, is necessary.
Schedules for maintenance and inspection are not fixedbecause they vary greatly according to the way in which thecustomer uses the VCR(VCP), and the environment in whichthe VCR(VCP) is used.But, in general home use, a good picture will be maintainedif inspection and maintenance is made every 1,000 hours.The table below shows the relation between time used andinspection period.
Table 1
(1) Grease : Kanto G-311G (Blue) or equivalent(2) Isopropyl Alcohol or equivalent(3) Cleaning Patches(4) Grease : Kanto G-381(Yellow)
(1) Cleaning video headFirst use a cleaning tape. If the dirt on the head is toostubborn to remove by tape, use the cleaning patch. Coatthe cleaning patch with Isopropyl Alcohol. Touch thecleaning patch to the head tip and gently turn thehead(rotating cylinder) right and left.(Do not move the cleaning patch vertically. Make surethat only the buckskin on the cleaning patch comes intocontact with the head. Otherwise, the head may be dam-aged.)Thoroughly dry the head. Then run the test tape. If lso-propyl Alcohol remains on the video head, the tape maybe damaged when it comes into contact with the headsurface.
(2) Clean the tape transport system and drive system, etc,by wiping with a cleaning patch wetted with IsporopylAlcohol.
1 It is the tape transport system which comes into contactwith the running tape. The drive system consists of thoseparts which moves the tape.
2 Make sure that during cleaning you do not touch the tapetransport system with the tip of a screw driver and no thatforce is that would cause deforming or damage applied tothe system.
2. Required Maintenance
3. Scheduled Maintenance
5) Maintenance Procedure5-1) Cleaning
NOTES:
About 1year
One hour
Two hours
Three hours
Wheninspection is
necessary
Averagehours usedper day
About 18months
About 3years
4. Supplies Required for Inspection and Maintence
Fig. C-9-4
Drum(Rotating Cylinder)
Head Tip
Coat With Isopropyl AlcoholTouch this section of cleaningpatch to the head tip and gentlyturn the Drum (Rotating Cylinder)
Cleaning Patch
MAINTENANCE/INSPECTION PROCEDURE
4-21
(1) Greasing guidelinesApply grease, with a cleaning patch. Do not use excessgrease. It may come into contact with the tape transportor drive system. Wipe any excess and clean with cleaning patch wetted in Isopropyl Alcohol.
(2) Periodic greasingGrease specified locations every 5,000 hours.
5-2) Greasing
NOTE:Greasing Points
3
5
6
1
2
4
1) Loading Path Inside & Top side2) Base Tension Boss inside Hole3) Arm Assembly F/L "U" Groove4) Arm Take-up Rubbing Section5) L/D Motor Gear Wheel Part
6) Shaft7) Arm Assembly F/L of Buming
Inside Hole8) Reel S, T Shaft (G381:Yellow)9) Brake T Groove
Guide Rail
Base Loading Gear Drive
Gear Sector Gear Cam
Gear Part
Bracket Side (L) Bracket Assembly Door
5
7
8
1
2
6
4
3
1) Loading Path Inside & Top side2) Shaft3) Gear Rack F/L Moving Section4) Shaft
5) Lever Tension Groove6) Clutch Assembly D33 Shaft7) Brake "S" Rubbing Section
Chassis (Top)
Chassis (Bottom)
Guide Rack F/L Gear Rack F/L
4-22
GEAR , F/R GEAR AY, P2 & P3
MECHANISM TROUBLESHOOTING GUIDE
4-23
Auto REW doesn't work.
Is the output of END sensor of supply side "H"?“H”: more than 3.5V
“L”: less than 0.7V~1V
Is the voltage across IR LEDbetween 0.8~1.5V?
Replace LED.
Is the Vcc. voltage of End sensor 5V? Check the syscon power.
Replace End sensor.
Check syscon circuit.
NO
YES
YES
YES
NO
NO
NO
1.Deck MechanismA.
NO
NO
NO
No F/R modes.
Is the present mode,F/R Mode?
Is the mode SW assembled correctly (refer to Pages 4-14.)
Is the normal voltage supplied tothe Capstan Motor Vcc1, Vcc2.?
Does terminal voltage(Vctl) ofCapstan Motor supply side
more than 4V?Check Servo, Power Circuits.
Replace the Capstan Motor.
Does the Capstan Motor rotate?
Do the T/Up, Supply Reelrotate?
Check syscon circuit.
YES
YES
YES
YES
YES
YES
B.
4-24
MECHANISM TROUBLESHOOTING GUIDE
AUTO STOP.(PLAY/CUE/REV)
Are there T/up and supply reelpulses.
In Play/Cue/Rev is the pinchroller in contact with the capstan
shaft.
Replace Reel Sensor.
Is the output of DFG, DPG OK?
Check aligment positions (page 4-14) Check spring Pinch.
Replace Drum Motor.
Check Servo, Syscon.
Check the Syscon, µ-COM.
No cassette loading.
Insert the cassette.
Check Holder Assembly CST.
Is there variation for CST IN S/WOutput?
(In Tape with REC Tab “L”→“H”→“L”)
(In Tape without REC Tab “L”→“H”→“L”→“H”)
Does the CST IN S/W worknormally?
Does the lever Assembly S/Wwork normally.
Check Syscon Circuit. Check Syscon Circuit.
Replace CST IN S/W.
YES
YES
YES
YES YES
YES
NO
NO
NO
NO
NO NO
NOYES
C.
D.
4-25
MECHANISM TROUBLESHOOTING GUIDE
In PB mode Tape Presencenot sensed.
Is the Pinch Roller attached to the Capstan Motor Shaft?
Check Alignment positions(page 4-14)
Does the T/Up Reel turn? Replace the Belt.Is the Belt ok?
Does the Drum Motor turn?
Are there DPG, DFG Pulses?
Are the T/Up Supply Reel Sensorsok?
Check Syscon,Circuit.
Check Syscon,Circuit.
Check Servo, Syscon.
Does the Capstan Motor turn?
Is the terminal voltage of theDrum Motor more than 2.3V?
Replace the Drum Motor.
Is the Vcc voltage of the DrumMotor normal?
Check the clutch and the IdlerAssembly.
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
Is the terminal voltage of CapstanMotor supplied more than 4V?
Replace the Capstan Motor.
Is the Voltage supplied to theCapstan Motor Vcc1,Vcc2 each?
YES
YES
YES
Check Servo,Power.
NO
NO
NO
E.
MECHANISM TROUBLESHOOTING GUIDE
4-26
Cassette cannot be inserted.
Does the Lever AssemblySwitch work?
Is the Lever Assembly SwitchSpring damaged or omitted?
Does the CST IN Switch worknormally?
Replace or add the LeverAssembly Switch Spring.
Is the Vcc of Main P.C.Board5V?
YESYES
Check syscon circuit.
YES
Check power circuit.
NO
Is the voltage between cassetteswitch and GND on Main
P.C.Board 5V??
YES
Is there a short circuit between cassetteswitch and GND on main P.C.Board?
Remove the short circuit part orReplace the main P.C.Board.
NO
Check Mode switch location andsyscon circuit.
Replace CST IN Switch.
YES
NOYES
NO NO
Replace CST IN Switch.NO
NO
Cassette will not eject.
Does the L/D motor rotate in reverse? Check L/D Motor or Drive IC.
Replace lever Assembly Switch.Does the Lever Assembly Switch work?
YESNO
NODoes the Arm Assembly F/L work normally?
YES
NODoes the Opener Door work?
YES
Replace Arm Assembly F/L.
Replace the Opener Door.
2. Front Loading MechanismA.
B.
MECHANISM TROUBLESHOOTING GUIDE
4-27
Cassette will not load.
Does the CST insert?
Does the opener Lid work?
Is the opener Door assembled correctly?
Replace the Opener Lid.
Replace the Arm Assembly F/L.
Check the power of L/D Motor.
Is the Holder Assembly Cassetteassembled correctly?
Replace the Gear Rack F/L.
Does the Gear Assembly Rack F/Lwork?
Does the Opener Door work?
Does the Arm Assembly F/L work?
Does the L/D Motor work?
Does the Holder Assembly Cassettemove the Arm Assembly F/L?
Replace the Front Loading Mechanism Assembly.
YES
YES
YES
YES
NO
NO
NO
YES NO
YES NO
YES NO
C.
4-28
EXPLODED VIEWS
117103
105117
100
106
107A
21
114113
112110115
A24
116
102
A23
032
A22
109054
054A
1. Front Loading Mechanism Section
EXPLODED VIEWS
4-29
401
402
001
008
001
031
079
017
032
024406
020
021028
019
018
029
030
026
A03
A04
A01
002
002A
025
027
022
003
004
006
007
010
405
014
015
009409
013
023016
405
012
402
2. Moving Mechanism Section(1)
EXPLODED VIEWS
4-30
051
052
517
061
056
058
518052A
055
060
410
070
069
076
032
077
068064
066065
067A
11
078
A12
3. Moving Mechanism Section(2)
MEMO
VICTOR COMPANY OF JAPAN, LIMITEDVIDEO DIVISION
Printed in Japan
S40894
3-21 3-22
BLOCK DIAGRAMS1. Power Block Diagram
5.4VATO SYS, TU/IF
HOT CIRCUIT
BD101 R101
R106 R102
C103
C113 C112
HOT GND
F101
WH(BL)
BK(BR)
PW101
6 7
8
9
10
3
2
4
3
11
12
1
2IC102
IC103
4
T101TRANSFORMER
4
2
3
1RECTIFIER& SMOOTHING
DRIVE & S/W BLOCKOVER CURRENT LIMITBLOCK
+
TO Canal+
TO TU/IF
12VA
TO CAPSTAN M24/12VA
33V
TO AV, TU/IF,5.2VT
TO DRUM12VA
5.2V
TO Hi-Fi, SensorSECAM
TIMER "H"
D155
SNUBBERBLOCK
(IC101, R109, C135, D103,
R103,C109, R125, R126)
(D102,R104,C105,C106)
(D109, C120,L104,C121)
NOTES : Symbol denotes AC ground.
Symbol denotes DC chassis ground.
!
!
!
!!
!
!
!
FROM µ-COM
FROM µ-COM
P.CTL"H"
LINE FILTERBLOCK
(C101,L102,C102)
RECTIFIER& SMOOTHING(D105, C115)
36V S/WBLOCK
(Q154, R157, R158,R155)
5VT SWBLOCK
(Q152, R153, R154, D156)
5V S/WBLOCK
PWR CTLBLOCK
Q163
(Q151, R151, R152)
(Q162, R161)
FEED-BACKBLOCK(R116,R117,R118R119,R120,R121C114)
'00 11. 30
F. µ-com SEARCH "H"
Q161R163
Q155
24V S/WQ159,R166,R167
RECTIFIER& SMOOTHING
(D106, C116,L103,C117)
RECTIFIER& SMOOTHING
(D110, C123)
3. VPS Block Diagram
1411
109
8
14
56
DAT
A/S
YN
VS
LIC
ER
CLO
CK
PLL
DAT
AA
QU
ISIT
ION
IIC B
US
INTE
RFA
CE
TIM
ING
VP
S B
LOC
KIC
7V1
SD
A56
50
141
5.2
VA
358 VPS V.out
59
CLK
60
DAT
A
55
DAV
VSUP
CVBS
Iref
VC01
VCS
CSO
SDA
SCL
GND
PD1
EH
BD
A V
IN
T1
PD2/VC02
23
7
1312
3-23 3-24
2. Tu/IF, NICAM & A2 Block Diagram
(From Power)
144
27 731
60
59
93
94
146
143
396
144
875
1415.4VA
5.2VT
S.V.W
3-25 3-26
4. Y/C Block Diagram(PB MODE)
90
93
96
84V.ENV
87
70
V.H
.SW
C.R
OTA
RY
DA
TA
CLO
CK
C.S
YN
C
V.O
UT
(MIC
OM
)
S2
V.O
UT
S1
V.O
UT
SYNC IN
69 68 67
C-Delay(1H/2H)BPFMAIN
CONVACCC LPF
CCDLPF
ACCDET
CNC
2521
IC201LA70100M
IC301LA71750M
29
18 14
PB FM EQ FM OEM
PB FM AGC
MAINDE EMP
Y-LPF
YNR
SUB LPF
60dB AMP
Y/C MIX
65 63 61
46
43Y-Delay
79 78
(REC MODE)
80
RE
C'H
'
V.H
.SW
C.R
OTA
RY
DA
TA
CLO
CK
C S
YN
C
V.O
UT
MIC
OM
V.IN
4F
RO
NT
V.IN
3D
EC
79 78 76 75 70 69 68 67 65 59 58 54 52
50 V.IN2 S1
V.IN1 TUNER48
46
43
33
32
31
CLK-IN2928
4.43MHz
2721
95
94
89
88
Killer C-LPF ACC
BPF
MainConv
MainConv
DETAILENH
NLEMPHA
W/DCLIP
IC301LA71750M
UP REC
SP REC
(To Drum)
(To Drum)
W/DCLIP
RECFM EQ
Y-LPF FBC
AGC
SW
Y-DELAY
KILL DEC
REC APC
VX02 VX02
COMPAMP
1H/2HDELAY
YNR
29 16
2 12
IC201 LA70100M
5. Hi-Fi Block Diagram
1 2 3 4 5 6 7 8 9 10
1316
1719
2021
3536
37
22
3233 31 30 29 28 27 26 25 24 23
Aud
io in
put
Blo
ck
• Tun
er• F
.A/V
• Sca
rt1• S
cart2
Mod
ulat
orA
.out
(To
Tune
r)S
cart
1A
udio
Out
Sca
rt 2
Aud
io O
ut
Nor
mal
A.o
ut(T
o AV
CP
)
Nor
mal
A.IN
(Fro
m A
VC
P)
Hi-F
iP
NR
Blo
ck
Hi-F
iR
EC
Blo
ck
A B
IC80
1
3-27 3-28
6. System Block Diagram
RC501, R5R7R5R7, R5R8C5R, C5R2
RC501
2fscR524, R514, R518,R516, R589, C577,C576, L501, Q504
LD(+)LD(-)
L/M CONTROLR525, R526
IC501HD6432197A
3-29 3-30
CIRCUIT DIAGRAMS1. Power Circuit Diagram
NOTES) Symbol denotes AC ground.
NOTES) Symbol denotes DC chassis ground.
NOTE) WarningNOTE) Parts that are shaded are criticalNOTE) With respect to risk of fire orNOTE) electricial shock.
BD101, R101 are defective.Power dead.
F101 is defective.Power dead.
IC101 is defective.Switching dead.
D102 is defective.No power.
D106 is defective.No 5.3VA and 5VG, 5VT.
No 14VA, 12VA are 12VT.D109, C120 are defective.
Q152 is defective.No 5.2VT.
IC102, IC103 are defective.Power dead.
NOTE : 1. Shaded( ) parts are critical for safety. Replace only
with specified part number.2. Voltages are DC-measured with a digital voltmeter
during TUNER mode.
3-31 3-32
2. Tuner, NICAM Circuit Diagram
EE MODE(VIDEO)
TU MODE (AUDIO)
FROMPOWER
F.A/V -
F.A/V -
To A/V -
F/To Hi-Fi
To Hi-Fi
F. SYS
3-33 3-34
3. A/V, SECAM, VPS Circuit Diagram
1
4
5
2
7
8 1311 12
239
1014
6
2
PB SECAM COLOR
REC AUDIOPB Y+C
PB Y
PB C
REC Y+C
REC Y
REC C
REC SECAM COLOR
PB AUDIO(MONO)
WAVEFORM
F/To SYS
Audio Tracking is failed.IC301 Pin 84 is defective.
PB COLOR Signal disappear.IC301 Pin 10 is defective.
EE, PB Screen doesn’t appear.Q305 is defective.
REC is failded.D301 or IC301 Pin30 is defective.
PB COLOR Signal disappear.IC301 Pin70 is defective.
PB COLOR Signal disappear.IC301 is defective.
D301or IC301 Pin 80REC is defective.
PB and Recording is failed.(IC301 doesn’t operate.)
IC301 Pin 69, 68 are defective.
Normal Audio signal is not recorded.FL301, Q301, Q306 are defective.
No mono Audio Signalin PB MODE.
Q302, Q303, Q314are defective.
4. System Circuit Diagram
8763 4
55
1
2
9
WAVEFORM
LED DOT MODEL ONLY
PWR
VCR
TIMER
REC/STANDBY
Q501, Q503 are defective.µ-COM is unstable.
IC505 is defective.VCR will not operate.
RC501 is defective.Remote control’s Pulse will not received.
X501 is defective.CLOCK SETTING will not operate.
X502 is defective.µ-COM will not operate.
ES501, ES502, LD501 aredefective.
Auto Rew will not working.RS501,RS502,Q514,Q515 are defective.
Auto stop occures.
R575, R576, R577,R578 are defective.
Deck will not operate.
IC504 is defective.
Reset is defective.Set dead.
3-35 3-36
3-37
WAVEFORM & VOLTAGE SHEET
IC301 Pin 20PB mode500mvp-p
IC301 Pins 38,32,3138, 38
Video in 1Vp-p
IC301 Pin 28PB/REC mode4.0Vp-p
IC301 Pin 7REC mode1.1Vp-p
IC301 Pin 6REC mode2.0Vp-p
IC301 Pin 29PB mode2.02Vp-p
IC301 Pin 41PB mode400mVp-p
IC301 Pin 64PB mode400mVp-p
IC301 Pin 23PB/REC mode5Vp-p
IC301 Pin 24PB/REC mode5Vp-p
IC301 Pins 71 72REC mode340mVp-p
IC301 Pins 51 54 PB mode300mVp-p
IC301 Pin 63PB mode400mVp-p
IC301 Pin 11PB mode3.6Vp-p
_ IC301 Oscilloscope Waveform
* IC501 Waveform Photographs
V.HSW(IC501 Pin 105)1V/10mSREC/PB MODE
DV.SYNC(IC501 PIN 109)1V/100uSQUE/REV MODE
CTL(+)(IC501 Pin 3)1V/10mS
CTL(-)(IC501 Pin4)1V/10mS
DFG/FG(IC501 PIN 103,104)1V/10mSREC/PB MODE
CFG(IC501 Pin9)1V/10mS
V.IN(IC501 Pin 17)500mV/20uS
V.OUT(IC501 Pin 19)500mV/20uSEE/PB MODE
C.SYNC(IC501 Pin 111)1.0V/100uSEE/PB MODE
3-38
3-39 3-40
5. Hi-Fi, SCART Circuit Diagram
V.OUT
V.IN
PB Hi-Fi
NORMAL Audio
F/To A/V
F/To SYS
F/To A/V
F. PWR
F/To PWR
F/To A/V
- To STSor SYSTEM
- F. POWER
F. SYS
F. S
YS
F. S
YS
F. P
WR
F/To A/V
F/SYS
F/SYS
F/SYS
F/To SYS
F/To Tuner
F/To A/V
All Audio is not appear.IC801 42, 43 Pins are defective.
• CIRCUIT VOLTAGE CHART
EE PB RECMODE
PIN NO.
R
A
K
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
10
2.45
-0.03
4.05
2.52
2.4
0
0
0
2.8
0
0
3.04
2.53
2.1
3.32
4.01
2.55
3.06
6.2
2.34
0.13
2.23
2.08
2.27
1.42
5.05
5.05
2.31
2.3
2.09
0.18
0.48
2.08
0
5.21
2.19
0
2.91
0
2.92
0
0
2.86
5.15
5.29
4.94
5.29
5.29
2.57
0
5.29
2.45
-0.03
4.06
2.52
2.41
3.35
2.59
0
3.72
0
0
3.02
2.51
2.08
1.96
4.01
2.54
1.94
3.2
4.25
3.44
2.21
2.22
2.4
1.43
5.02
5.02
2.07
2.02
2.08
0.19
0.26
2.07
0.01
5.2
2.2
0
2.91
0
2.92
0
0
2.86
5.16
5.29
4.94
5.29
5.2
2.57
0
5.29
2.44
0
4.07
2.52
2.41
3.37
0
0
0
0
0
3.04
0
2.19
3.25
4.01
2.56
3.06
3.22
0.22
0.13
2.22
2.06
2.28
0
5.06
5.06
2.37
2.38
2.11
0.18
0.41
2.11
0
5.21
2.19
0
2.91
0
2.92
0
0
2.85
0
5.29
4.94
5.29
5.29
2.57
0
5.29
I C 1 0 3
I C 2 0 1
I C 4 0 1
I C 4 0 2
EE PB RECMODE
PIN NO.
11
12
13
14
15
16
17
18
31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
2.41
2.1
0
5.26
0
0
0
0
5.15
0.02
2.29
2.28
2.29
2.28
2.27
2.26
2.29
2.37
0
2.26
2.26
5.17
2.26
5.17
4.24
0
3.36
3.07
3.06
5.16
0.13
1.44
2.07
4.23
2.83
0
4.7
4.7
2.85
0.33
2.17
3.35
2.09
1.99
9.45
0
0
5.17
2.4
2.34
2.33
2.69
2.41
2.1
5..29
5.26
0
0
0
0
5.14
0.03
2.29
1.46
2.26
2.28
2.28
2.27
2.26
2.29
2.39
0.02
2.3
0.02
2.26
0.16
2.26
5.17
4.25
0
1.96
3.06
3.03
5.16
3.44
1.82
2.1
4.21
2.83
0
4.7
4.7
2.06
0.31
2.16
3.35
2.11
2.03
9.43
0
0
5.16
2.42
4.42
2.46
2.67
2.42
2.08
5.29
5.25
0
0
0
0
1.7
0.75
0
0.5
2.47
2.29
2.27
2.27
3.05
2.28
2.28
0.11
2.28
2.29
5.05
2.27
5.14
3.07
0
3.25
3.06
3.05
5.13
5.13
0
1.42
4.18
2.9
0
4.69
4.69
2.07
0.31
2.16
3.35
2.09
2.02
9.39
0
0
5.14
2.39
0.08
2.46
2.68
I C 3 0 1
EE PB RECMODE
PIN NO.
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
4.17
2.35
3.18
1.97
0
1.97
2.34
1.97
5.24
2.25
2.02
2.37
2.94
1.42
1.72
0.09
1.75
0
1.85
0
0.
4.79
4.75
5.27
0.01
5.13
2.55
2.46
2.47
1.59
2.7
2.02
1.06
1.11
0
5.13
0.46
0
0
0.71
0.71
0.71
5.17
0
1.95
1.95
1.95
1.95
0
2.29
0
2.29
4.17
2.37
3.18
1.97
0
1.97
2.35
1.99
5.24
2.31
2.14
2.95
1.55
1.85
0.11
1.84
0
1.85
0
0.44
4.91
4.81
2.69
0
5.11
1.98
2.63
2.63
0.77
1.59
3.39
1.91
1.06
1.12
0
1.47
2.43
0
0
0.72
0.72
0.72
0.72
5.16
0
1.93
1.93
1.93
1.93
0
2.29
2.29
2.29
4.17
2.33
3.18
1.97
0
1.97
2.35
1.99
5.24
2.29
1.99
2.4
2.93
1.38
2.05
0.11
0.
1.81
0
0.4
4.81
4.79
2.69
0.01
5.09
2.21
2.53
2.45
2.45
1.49
2.69
2.52
4.72
1.11
0
1.51
1.75
1.36
2.03
0.7
0.7
0.7
0.7
5.11
0
0.73
0.72
0.72
4.33
0
2.4
2.4
2.53
EE PB RECMODE
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
0
2.39
2.57
2.57
2.57
2.56
2.58
2.55
4.62
4.85
1.89
1.89
2.61
0.4
0.08
1.99
2.39
5.14
2.41
0
2.47
2.46
0
0.51
2.81
5.27
2.46
5.27
5.22
0
0.17
0.12
0.18
0.31
5.27
5.28
4.93
4.88
2.29
0
0
0
4.88
5.24
0
0
0
0
0.01
5.25
4.48
5.28
0
5.25
0
2.57
2.57
2.57
2.57
2.57
2.59
2.55
2.31
5.16
1.91
1.9
2.5
0.4
0.1
1.91
2.34
5.14
2.37
0
2.47
2.46
0
2.47
2.88
2.28
2.5
5.28
5.27
5.01
0.18
0.3
5.28
5.29
4.94
4.88
2.29
0
0
0
4.88
5.25
0
0
0
0
5.28
0
0.04
5.29
0
5.26
0
2.57
3.04
2.1
2.57
2.57
2.58
2.55
2.31
5.016
1.9
1.89
2.49
0.4
0.56
1.98
2.31
5.11
2.33
0
0
0
0
0.01
2.8
5.28
2.54
5.28
5.27
0.05
1.9
0.18
0.43
5.28
5.28
4.94
4.87
2.28
0
0
0
4.87
5.24
0
0
0
0
0
0.02
5.29
0
5.27
I C 5 0 1
EE PB RECMODE
PIN NO.
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
5.27
5.27
0
0
4.91
4.91
5.17
5.17
2.84
5.14
0.01
5.1
0.83
0.01
0.01
5.29
5.29
0.03
5.24
0
1.49
1.3
5.27
2.55
0
5.29
3.25
5.28
0
0
0
2.65
0
0
0
0
0
0.95
0
0
0.29
0
0
5.26
0
0.01
0.7
0
0.12
0.12
0
0
0
0
0.05
5.29
5.28
0
0
4.92
4.91
5.18
5.19
2.83
5.14
0.01
5.11
0.83
5.3
5.3
5.3
0
0.03
5.23
0
1.5
1.4
5.27
2.53
0
2.58
3.25
5.28
2.7
2.77
3.55
2.68
3.3
0
0
0
0
5.16
0
0
0.1
0
0
5.26
2.7
0
0.13
0
1.39
1.39
2.7
2.64
2.75
2.78
0.05
0.08
5.28
0
0
4.79
4.79
5.18
5.18
2.86
5.15
0.02
5.11
0.89
5.3
5.3
5.3
0.01
0.04
5.22
0
1.5
1.21
5.27
2.54
0
2.58
3.25
5.28
2.69
2.77
3.55
2.86
3.21
0
0
0
0
0
0
0.07
0
0
5.25
0
0
0.57
0
1.39
1.39
0
5.12
2.74
2.77
0.05
EE PB RECMODE
PIN NO.
110
111
112
1
2
3
4
5
6
7
8
1
2
3
1
2
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
0
4.2
5.29
0
0
0
0
5.01
5.01
0
5.29
5.28
0
5.28
5.28
0
4.87
0
5.01
5.01
0
5.28
5.28
0
0
0.01
0
0.01
1.56
0.99
5.28
2.84
2.92
2.91
2.82
2.8
2.8
2.79
2.78
2.79
2.79
2.77
2.76
2.71
2.49
2.48
2.64
2.64
1.48
2.63
0
0.4
5.28
0
0
0
0
4.95
4.95
0
5.29
5.28
0
5.28
5.28
0
4.87
0
4.94
4.94
0
5.28
5.28
0
0
0.01
0
0
1.56
0.99
5.29
2.91
2.91
2.9
2.81
2.86
2..86
2.85
2.85
2.84
2.84
2.83
2.82
2.75
2.51
2.51
2.67
2.68
2.57
2.67
0
0.4
5.27
0
0
0
0
4.79
4.8
0
5.28
5.28
0
5.28
5.28
0
4.87
0
4.79
4.78
0
0.39
2.66
0
2.31
2.36
2.31
1.56
1.39
5.28
2.7
2.81
2.81
2.68
2.67
2.66
2.65
2.65
2.66
2.66
2.65
2.64
2.59
2.33
2.32
2.49
2.5
2.32
2.5
I C 5 0 3
I C 5 0 4
I C 5 0 5
I C 7 V 1
I C 8 0 1
EE PB RECMODE
PIN NO.
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
2.6
2.57
2.66
2.63
2.5
2.52
2.36
0.01
2.51
2.6
2.34
0.03
0.03
12.6
3.35
3.29
3.29
3.55
0
5.2
2.27
4.96
5.05
2.8
5.14
1.51
1.51
0
2.47
2.47
0.54
0
0
0
5.16
4.91
4.9
2.58
2.58
2.41
0.53
0.54
5.13
0
0.53
5.16
0
0
0
0
0.05
0
0
2.63
2.59
2.86
2.64
2.5
2.53
2.37
0
2.47
2.57
2.41
0.02
0.04
12.5
3.31
3.3
3.3
3.56
0
5.2
2.29
4.98
5.06
2.79
5.15
1.51
1.51
0
2.48
2.48
0.5
0
0
0
5.16
4.86
4.8
0.51
0.5
0.51
0.53
0.51
5.14
0
0.51
5.16
0.02
0.02
0
0.05
0.05
0
0
2.5
2.47
2.55
2.51
2.39
2.4
2.27
0
2.41
2.46
1.38
-0.07
-0.06
12.57
2.89
2.9
2.9
3.42
0.01
5.21
2.5
4.91
4.97
2.69
5.15
1.51
1.51
0
2.48
2.48
0.46
0.45
0.45
0
5.16
4.79
4.79
0.57
0
0.57
0
0.58
5.14
0
0
5.16
0
0
0
0
0
0
2.8
I C 7 5 1
3-41 3-42
3-43 3-44
EE PB RECMODE
PIN NO.
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
2.8
2.79
0
5.16
4.2
0
2.8
2.84
2.85
2.59
2.31
3.3
2.8
2.79
0.02
5.14
4.2
0
2.8
2.84
2.83
2.59
2.31
2.8
2.79
0
5.15
4.21
0
2.8
0
0
0
2.79
2.79
2.59
2.3
0
EE EE EEEE Mode PB Mode REC Mode
PB PB PBREC REC RECTran-sistor
Q151
Q152
Q154
Q155
Q157
Q159
Q161
Q162
Q163
Q164
Q165
Q166
Q301
Q302
Q303
Q304
Q305
Q306
Q307
Q308
Q309
Q501
Q502
Q503
Q504
Q5S1
Q514
Q515
Q906
Q901
Q7S1
Q902
Q903
4.55
5.31
32.99
12.73
0.03
29.84
0.03
0.02
0.03
-0.03
14.06
4.4
0
5.18
0.01
0.01
2.01
5.14
2.69
2.66
3.09
0
0
5.3
0
0.43
0
0
0
0
0
12.73
0
5.34
5.31
33.53
12.68
0.03
29.79
0.03
-0.02
0.03
-0.03
13.74
5.3
0
5.18
0
0
2.53
5.19
2.69
2.63
3.05
0
0
5.3
0.05
2.22
0
0
0
0
0
12.66
0
5.3
5.3
33.76
12.76
-0.03
30.14
-0.03
-0.02
-0.03
-0.03
13.95
5.3
0
5.14
-18.22
-18.22
2.5
1.9
2.64
2.6
3.01
0
0
5.3
0.05
1.92
0
0
0
0
0
12.72
0
5.3
4.52
32.34
13.4
0.84
29.78
0
0.69
5.18
4.38
-0.01
5.3
0.01
5.18
-0.42
-0.4
1.29
5.19
1.98
1.98
2.41
0.67
0.71
4.61
0.14
0
5.09
0
0.12
5.26
0
0.01
0
4.54
4.52
32.89
13.35
0.84
29.8
0
0.69
5.18
4.38
-0.01
4.41
0
4.52
0.69
0.71
1.83
5.16
1.98
1.96
2.37
0.67
0.22
4.61
0.63
0
0.07
5.25
0
0.01
0
4.55
4.51
33.12
13.42
0.84
30.13
0
0.69
5.18
4.38
-0.01
4.4
0.75
5.13
-24.85
-24.7
1.81
2.14
1.93
1.93
2.33
0.67
0.23
4.61
0.67
0
0.13
5.25
0
0.01
0
5.24
5.22
32.97
14.05
4.38
13.21
29.82
0
0.03
-0.01
14.04
5.11
5.15
-0.42
0
0
0
5.19
0
0
0
0.01
0.01
5.28
2.69
1.61
0.01
5.16
1.93
0.01
1.32
12.73
12.72
5.24
5.22
33.5
13.77
4.38
12.48
29.8
0
0.03
-0.01
13.71
5.13
5.15
5.12
0.01
0
0
5.19
0
0
0
0.01
2.33
5.28
2.65
2.53
2.37
0.01
12.66
12.64
5.24
5.22
33.72
13.98
4.38
12.73
30.11
0
0.03
0
13.95
5.1
1.69
-24.71
0.01
0
0
4.89
0
0
0
0.01
2.29
5.28
2.67
2.5
2.4
0.01
0.98
12.71
12.71
3-45 3-46
LOCATION GUIDE
PRINTED CIRCUIT BOARD DIAGRAMS1. MAIN P.C.Board
(Solder Side)
5-1
SECTION 5REPLACEMENT PARTS LIST
SAFETY PRECAUTIONParts identified by the ! symbol are critical for safety. Replace only with specified part numbers.
5.1.1 PACKING AND ACCESSORY ASSEMBLY <M1>The instruction manual to be provided with this product will differ according to the destination.
OPTIONAL PARTS
CABLE SET ASS'Y(Optional parts)
810
BATTERY808
806
PLUG ASS'Y 2WAY(Optional parts)
812
PLUG ASS'Y 1WAY(Optional parts)
811
REMOCON900
PACKING (RF)803
PACKING (LF)803
BOX CARTON802
BAG. SOFR SHEET804
INSTRUCTION MANUAL801
SCART CABLE821
5.1 EXPLODED VIEW
5-2
5.1.2 FINAL ASSEMBLY <M2>
BEWARE OF BOGUS PARTSParts that do not meet specifications maycause trouble in regard to safety and per-formance. We recommend that genuine JVCparts be used.
452330
260
300
250462
462
A43
283
280
284
277
A42
A49
281
OPTIONAL PARTS
A46
323
TU701(TUNER)
2SCART
1SCART
452320
452
452
275LED502(LED501)
A00
457464
5-3
051
052
517
061
056
058
518052A
055
060
410
070
069
076
032
077
068064
066
065
067A11
078
A12
401
402
001
008
011
031
079
017
032
024406
020
021028
019
018
029
030
026
A03
A04
A01
002
002A
025
027
022
003
004
006
007
010
405
014
015
009409
013
023 016
405
012
402
117103
105 117
100
106
107A21
114113112
110
115
A24
116
102
A23
A22
109054
054A [ BOTTOM VIEW ]
[ TOP VIEW ]
5.1.3 MECHANISM ASSEMBLY <M4>
# REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN # REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN
5-4
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------ ---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
******************************PACKING AND ACCESSORY ASSEMBLY <M1>
801 LG-3835RP0075B INSTRUCTION ASSEMBLY (EN,GE,FR,IT,DU) A C801 LG-3835RP0075C INSTRUCTION ASSEMBLY (PT,GR,SP) A C801 LG-3835RP0075D INSTRUCTION ASSEMBLY (SW,DA,FI,NO,GE) A C801 LG-3835RP0075E INSTRUCTION ASSEMBLY (EN,GE,FR,IT,DU) B DE J801 LG-3835RP0075F INSTRUCTION ASSEMBLY (PT,GR,SP) B DE J801 LG-3835RP0075G INSTRUCTION ASSEMBLY (SW,DA,FI,NO,GE) B DE J801 LG-3835RP0075H INSTRUCTION ASSEMBLY (FR) FG801 LG-3835RP0075K INSTRUCTION ASSEMBLY (EN) I801 LG-3835RP0075L INSTRUCTION ASSEMBLY (PO,CZ,HU) K M801 LG-3835RP0075M INSTRUCTION ASSEMBLY (EN) H801 LG-3835RP0075N INSTRUCTION ASSEMBLY (PO,CZ,HU) L N802 LG-3890R-H768D BOX EDJ200P NA3GJJX SW3-A 0.858 4 ABCDEFGH I JKLMN803 LG-3920R-0067A PACKING AF999NS 0.02 65 EPS 12 1190 23 ABCDEFGH I JKLMN804 LG-292-053A BAG SOFT(VCP) ABCD FG K804 LG-3880R-H001A BAG HDPE 500 500 0.03 VCR MIDI E H I J LMN806 LG-6850R-CAA26 CABLE,COAXIAL 1200M/M PAL-PAL DOUBLE SHIELD ABCDEFGH I JKLMN808 — BATTERY,MANGANESE AAAM(R03) SEOTONG 1-5 V - 1PA ABCDEFGH I JKLMN810 LG-6851RP0003A CABLE ASSY,RF CABLE ASSY,RF/SCART/RCA USING ABCDEFGH I JKLMN821 LG-6850R-SMA21 CABLE,COAXIAL 14PIN 1200M/M SCART-SCART DOUB FG900 LG-6711R1P037A REMOTE CONTROLLER ASSEMBLY N5 NOR EDJ209P NA3GJJX JVC W/S B D FGH I L N900 LG-6711R1P037B REMOTE CONTROLLER ASSEMBLY N5 EDJ200P NAEGJJX JVC W/O SHO A C K M900 LG-6711R1P037C REMOTE CONTROLLER ASSEMBLY N5 EDJ209P NA6NJJY JVC W/SHOWV E J
MODEL MARK MODEL MARK MODEL MARKHR-J285EU A HR-J595MS F HR-J282EU KHR-J290EU B HR-J295MS G HR-J283EU LHR-J585EU C HR-J595EK H HR-J582EU MHR-J590EU D HR-J295EK I HR-J583EU NHR-J593EU E HR-J293EU J
5.2 REPLACEMENT PARTS LIST
******************************FINAL ASSEMBLY <M2>
A00 LG-6721RF0700D DECK ASSEMBLY,VIDEO D35(N) DI(2HD, SP ONLY, AHC(X) AB G JKLA00 LG-6721RF0710D DECK ASSEMBLY,VIDEO D35(N) DI (2HD, NP, AHC(X), B/ IA00 LG-6721RF0750D DECK ASSEMBLY,VIDEO D35(N) DI (4HF, PAL, AHC(X), B CDEF H MNA43 LG-3721R-F253A PANEL ASSEMBLY,FRONT EDJ200P (J285EU) AA43 LG-3721R-F253B PANEL ASSEMBLY,FRONT EDJ209P (J290EU) BA43 LG-3721R-F253C PANEL ASSEMBLY,FRONT EDJ904NS (J595MS) FA43 LG-3721R-F253D PANEL ASSEMBLY,FRONT EDJ900NP (J585EU) CA43 LG-3721R-F253E PANEL ASSEMBLY,FRONT EDJ209P (J293EU) JA43 LG-3721R-F253F PANEL ASSEMBLY,FRONT EDJ909NP (J590EU) DA43 LG-3721R-F253G PANEL ASSEMBLY,FRONT EDJ909NP (J593EU) EA43 LG-3721R-F253H PANEL ASSEMBLY,FRONT EDJ204S (J295MS) GA43 LG-3721R-F253J PANEL ASSEMBLY,FRONT EDJ904NI(J595EK) HA43 LG-3721R-F253K PANEL ASSEMBLY,FRONT EDJ200Y (J282EU) KA43 LG-3721R-F253L PANEL ASSEMBLY,FRONT EDJ203Y (J283EU) LA43 LG-3721R-F253M PANEL ASSEMBLY,FRONT EDJ203NI (J295EK) IA43 LG-3721R-F253N PANEL ASSEMBLY,FRONT EDJ903NY (J583EU) NA43 LG-3721R-F253Q PANEL ASSEMBLY,FRONT EDJ900NY (J582EU) MA46 LG-3501R-5739A BOARD ASSEMBLY JVC DI EC(D) SERIES B JA46 LG-3501R-5739B BOARD ASSEMBLY JVC DI EC(D) SERIES AA46 LG-3501R-5739C BOARD ASSEMBLY JVC DI EC(D) SERIES FA46 LG-3501R-5739D BOARD ASSEMBLY JVC DI EC(D) SERIES CA46 LG-3501R-5739E BOARD ASSEMBLY JVC DI EC(D) SERIES DEA46 LG-3501R-5739F BOARD ASSEMBLY JVC DI EC(D) SERIES GA46 LG-3501R-5739G BOARD ASSEMBLY JVC DI EC(D) SERIES MNA46 LG-3501R-5739H BOARD ASSEMBLY JVC DI EC(D) SERIES HA46 LG-3501R-5739J BOARD ASSEMBLY JVC DI EC(D) SERIES KLA46 LG-3501R-5739K BOARD ASSEMBLY JVC DI EC(D) SERIES I250 LG-3110R-0128C CASE TOP(Q280G:B/K),SIDE E J250 LG-3110R-0223G CASE TOP( 0128 A288G SIDE SCREW 4EA ABCD FGH I KLMN260 LG-3210R-0023B FRAME MAIN (VII-PJT, 60HR) ABCDEFGH I JKLMN280 LG-3720R-F193A PANEL,VIDEO FRONT(B589G-SLVER) ABCD FGH I KLMN280 LG-3720R-F193B PANEL,VIDEO FRONT (Q280G) E J283 LG-3580R-V031A DOOR,CASE CST (VCR) (MONO-B589G-SILVER) AB G I KL283 LG-3580R-V031B DOOR,CASE CST (VCR) (MONO-Q280G-B.K) J283 LG-3580R-V031C DOOR,CASE CST (VCR) (HIFI-B589G-SILVER) CD F H MN283 LG-3580R-V031D DOOR,CASE CST (VCR) (HIFI-Q280G-BK) E284 LG-442-681A SPRING DOOR ABCDEFGH I JKLMN
! 300 LG-6410RBHV01A POWER CORD H03VVH2-F2 X 0.75MM FILTER VOL H I ! 300 LG-6410RCHP03B POWER CORD HIT-102/H03VVH2-F (NM) HARNESS ABCDEFG JKLMN
320 LG-3720R-D020A PANEL DISTRIBUTOR (PAL-1SCART) A I KL320 LG-3720R-D020B PANEL DISTRIBUTOR (PAL-SCART MONO) B G J320 LG-3720R-D020C PANEL DISTRIBUTOR (PAL-2SCART HI-FI) DEF H320 LG-3720R-D020D PANEL DISTRIBUTOR (PAL-1SCART HI-FI) C MN323 LG-3111R-0089C CASE ASSEMBLY PRE-AMP (02-PAL) ABCDEFGH I JKLMN330 LG-3550R-0210A COVER BOTTOM(LARGE) ABCDEFGH I JKLMN452 LG-353-051A SCREW SPECIAL ABCDEFGH I JKLMN457 LG-353-051E SCREW SPECIAL (3X12) ABCDEFGH I JKLMN462 LG-353-136A SCREW SPECIAL(FBK) (353S353A) ABCDEFGH I JKLMN
******************************MECHANISM ASSEMBLY <M4>
A01LG-6723R-0401A DRUM(CIRC) ASSEMBLY D35-2CH SP ONLY (8P2) AB G JKL
A01 LG-6723R-0401B DRUM(CIRC) ASSEMBLY D35-2CH SP/EP (8M2) IA01 LG-6723R-0403C DRUM(CIRC) ASSEMBLY D35-6CH PAL (8P6C) CDEF H MNA04 LG-4421R-0008A BRAKE ASSEMBLY RS AB G JKLA04 LG-4811RF0038A BRACKET ASSEMBLY L/D(S) ABCDEFGH I JKLMNA11 LG-4471R-0005A GEAR ASSY P3 ABCDEFGH I JKLMNA12 LG-4471R-0004A GEAR ASSY P2 ABCDEFGH I JKLMNA21 LG-4931R-0047A HOLDER ASSY CST ABCDEFGH I JKLMNA22 LG-4471R-0006A GEAR ASSY RACK F/L ABCDEFGH I JKLMNA23 LG-4261R-0023A ARM ASSY F/L ABCDEFGH I JKLMNA24 LG-4510R-0046A LEVER ASSY SWITCH ABCDEFGH I JKLMN001 LG-6723R-0304A DRUM(CIRC) ASSEMBLY SUB D35-2CH (8P2) AB G JKL001 LG-6723R-0304B DRUM(CIRC) ASSEMBLY SUB D35-2CH (8M2) I001 LG-6723R-0306C DRUM(CIRC) ASSEMBLY SUB D35-6CH (8P6C) CDEF H MN002 LG-4680R-B005A MOTOR(MECH) DRUM I2OAL05 SEJIN-SANKYO ICLE ABCDEFGH I JKLMN002A LG-5202R00002C BRUSH,CARBON ASSY D33 (TIP+2 SPRING) 1.4, ABCDEFGH I JKLMN003 LG-4930R-0284A HOLDER,SHELF FPC(6CH) ABCDEFGH I JKLMN004 LG-5006R-0034A CAP FPC ABCDEFGH I JKLMN008 LG-6850R-HG18Z CABLE,FLAT P=1.25 FFC UL2896(0.05X0.8) 7 ABCDEFGH I JKLMN009 LG-4260R-0038A ARM T/UP(D35) ABCDEFGH I JKLMN010 LG-4810R-0125A BRACKET CHASSIS ABCDEFGH I JKLMN011 LG-4261R-0022A ARM ASSY TENSION(D35) ABCDEFGH I JKLMN012 LG-3041R-0037A BASE ASSY P2 ABCDEFGH I JKLMN013 LG-3041R-0038A BASE ASSY P3 ABCDEFGH I JKLMN014 LG-3041R-0039A BASE ASSY P4 ABCDEFGH I JKLMN015 LG-5870R-0005A OPENER LID(D35) ABCDEFGH I JKLMN016 LG-3041R-0036A BASE ASSEMBLY A/C HEAD (ALPS) ABCDEFGH I JKLMN017 LG-4408R-0003A REEL S ABCDEFGH I JKLMN018 LG-4970R-0140A SPRING COIL RS D35 ABCDEFGH I JKLMN019 LG-4421R-0008A BRAKE ASSEMBLY RS CDEF H I MN020 LG-4970R-0128A SPRING COIL D35 (TB) ABCDEFGH I JKLMN021 LG-4421R-0006A BRAKE ASSY T ABCDEFGH I JKLMN022 LG-6520D00002A HEAD(CIRC) D35 FE ST FE HEAD ABCDEFGH I JKLMN023 LG-3040R-0057A BASE LOADING ABCDEFGH I JKLMN024 LG-4261R-0029A ARM ASSEMBLY IDLER (N) ABCDEFGH I JKLMN025 LG-4810R-0118A BRACKET L/D(S) ABCDEFGH I JKLMN026 LG-4680R-D002A MOTOR(MECH) LOADING MDB2B66 SANKYO D35 ASP ABCDEFGH I JKLMN027 LG-4470R-0093A GEAR WHEEL ABCDEFGH I JKLMN028 LG-4408R-0004A REEL T ABCDEFGH I JKLMN029 LG-4261R-0019A ARM ASSY PINCH ABCDEFGH I JKLMN030 LG-4510R-0043A LEVER T/UP ABCDEFGH I JKLMN031 LG-4970R-0123A SPRING COIL TENSION(D35) ABCDEFGH I JKLMN032 LG-3141R-0040A CHASSIS ASSY D35 ABCDEFGH I JKLMN051 LG-4400R-0005A BELT CAPSTAN ABCDEFGH I JKLMN052 LG-4680R-A007A MOTOR(MECH) CAPSTAN F2QVB06 SANKYO D35 ASR ABCDEFGH I JKLMN052A LG-4980R-0023A SUPPORTER CAPSTAN(D35) ABCDEFGH I JKLMN054 LG-4470R-0100A GEAR RACK F/L ABCDEFGH I JKLMN054A LG-4970R-0124B SPRING COIL D35 (RACK F/L) ABCDEFGH I JKLMN055 LG-4470R-0097A GEAR DRIVE(D35) ABCDEFGH I JKLMN056 LG-4470R-0096A GEAR CAM(D35) ABCDEFGH I JKLMN058 LG-4421R-0007A BRAKE ASSY CAPSTAN ABCDEFGH JKLMN060 LG-4510R-0040A LEVER F/R(D35) ABCDEFGH I JKLMN061 LG-4265R-0006A CLUTCH ASSEMBLY D35 (N) ABCDEFGH I JKLMN064 LG-4470R-0098A GEAR SECTOR(D35) ABCDEFGH I JKLMN065 LG-4261R-0021A ARM ASSY P3 ABCDEFGH I JKLMN066 LG-4970R-0122A SPRING COIL D35 ABCDEFGH I JKLMN067 LG-4470R-0095A GEAR P3 ABCDEFGH I JKLMN068 LG-4470R-0094A GEAR P2 ABCDEFGH I JKLMN069 LG-4970R-0122A SPRING COIL D35 ABCDEFGH I JKLMN070 LG-4261R-0020A ARM ASSY P2 ABCDEFGH I JKLMN076 LG-4510R-0047A LEVER SPRING ABCDEFGH I JKLMN077 LG-3300R-M116A PLATE SLIDER ABCDEFGH I JKLMN078 LG-4510R-0041A LEVER TENSION ABCDEFGH I JKLMN079 LG-3040R-0056A BASE TENSION(D35) ABCDEFGH I JKLMN100 LG-3301R-M022A PLATE ASSEMBLY TOP ABCDEFGH I JKLMN102 LG-4970R-0130A SPRING COIL D35 (STOPPER) ABCDEFGH I JKLMN103 LG-4930R-0276A HOLDER,SHELF SIDE(L) ABCDEFGH I JKLMN105 LG-4930R-0274A HOLDER,SHELF CST ABCDEFGH I JKLMN106 LG-4930R-0275A HOLDER,SHELF SIDE(R) ABCDEFGH I JKLMN107 LG-4510R-0044A LEVER STOPPER ABCDEFGH I JKLMN109 LG-5870R-0004A OPENER DOOR ABCDEFGH I JKLMN110 LG-4260R-0035A ARM F/L(L) ABCDEFGH I JKLMN112 LG-3070R-0002A BODY F/L ABCDEFGH I JKLMN113 LG-4970R-0127A SPRING COIL D35 (F/L(R)) ABCDEFGH I JKLMN114 LG-4260R-0036A ARM F/L(R) ABCDEFGH I JKLMN115 LG-4510R-0042A LEVER SWITCH ABCDEFGH I JKLMN116 LG-4970R-0138A SPRING COIL D35 SWITCH ABCDEFGH I JKLMN117 LG-3300R-M137A PLATE SPRING CST ABCDEFGH I JKLMN401 LG-1MEC0261518 SCREW MACHINE,PAN HEAD SPR W D2.6 L4.5 MSWR3/FZY ABCDEFGH I JKLMN402 LG-1MPC0261418 SCREW MACHINE,PAN HEAD D2.6 L4.0 MSWR3/FZY ABCDEFGH I JKLMN405 LG-1SZZR-0031B SCREW,DRAWING D2.6 L5.8 SWRCH16A/FZY TAP ABCDEFGH I JKLMN406 LG-1MEC0302018 PAN HEAD MACHINE SCREW S/W + D3.0 L6.0 MSWR3/FZY ABCDEFGH I JKLMN409 LG-1SZZR-0032B SCREW,DRAWING D2.6 L5.0 SWRCH18A/FZY TAP ABCDEFGH I JKLMN410 LG-1APF0262218 SCREW TAP TITE(B),PAN HEAD D2.6 L6.8 MSWR3/FZY ABCDEFGH I JKLMN517 LG-1WZZR-0004D WASHER STOPPER ABCDEFGH I JKLMN518 LG-1WZZR-0004A WASHER STOPPER ABCDEFGH I JKLMN
# REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN # REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN
5-5
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------ ---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
******************************MAIN BOARD ASSEMBLY <03>
PBM00 LG-6871R-5739A PWB(PCB) ASSEMBLY,TOTAL EDJ209P (PCB ASSY) B JPBM00 LG-6871R-5739B PWB(PCB) ASSEMBLY,TOTAL EDJ200P (PCB ASSY) APBM00 LG-6871R-5739C PWB(PCB) ASSEMBLY,TOTAL EDJ904NS (PCB ASSY) FPBM00 LG-6871R-5739D PWB(PCB) ASSEMBLY,TOTAL EDJ900NP (PCB ASSY) CPBM00 LG-6871R-5739E PWB(PCB) ASSEMBLY,TOTAL EDJ909NP (PCB ASSY) DEPBM00 LG-6871R-5739F PWB(PCB) ASSEMBLY,TOTAL EC(D) SERIES (PCB ASSY) GPBM00 LG-6871R-5739G PWB(PCB) ASSEMBLY,TOTAL EDJ SERIES (HIFI) MNPBM00 LG-6871R-5739H PWB(PCB) ASSEMBLY,TOTAL EDJ904NI (HIFI) HPBM00 LG-6871R-5739J PWB(PCB) ASSEMBLY,TOTAL EDJ SERIES (MONO) KLPBM00 LG-6871R-5739K PWB(PCB) ASSEMBLY,TOTAL EDJ203I (MONO) IIC101 STR-A6351 IC,POWER MANAGEMENT STR-A6351 SANKEN 8 DIP ST SMPS ABCDEFGH I JKLMN
! IC102 LTV-817B SENSOR LTV-817B,PHOTO COUPLER(LITEON) ABCDEFGH I JKLMNIC103 LG-0IKE431000A IC,KEC KIA431 3 PIN TP ABCDEFGH I JKLMNIC201 LG-0ILNRSA007A IC,LINEAR LA70100M SANYO 30 SOP ST SECAM FGIC301 LG-0ILNRSA005A IC,LINEAR LA71750AM SANYO 100 QFP TRAY A ABCDEFGH I JKLMNIC501 LG-0IMCRHI014B IC,MICRO CONTROLLER HD6432197SA06F HITACHI 112 QFP ABCDEFGH I JKLMNIC501 LG-0IMCRHI019A IC,MICRO CONTROLLER HD6432197SA09F HITACHI 112P QF KLMNIC503 LG-0IAL241600B IC,ATMEL AT24C16 - - - - ABCDEFGH I JKLMNIC504 LG-0IKE703100A IC,KEC KIA7031P 3P 3.1V RESET(TAPING) ABCDEFGH I JKLMNIC505 LG-0IKE704200B IC,KEC KIA7042P 3P 4.2V RESET(TAPING) ABCDEFGH I JKLMNIC751 LG-0IIT341700B IC,ITT MSP3417D-QG QFP44 BK NICAM+A2 CDEF H MNIC7V1 LG-0ILNRMN001A IC,LINEAR SDA5650 MICRONAS 14 DIP ST VPS B DE JIC801 LG-0IPH960500A IC,PHILIPS TDA9605H QFP44 BK HIFI AMP+HIF CDEF H MNIC901 MM1443XJ IC,MITSUMI MM1443XJ SSOP-34 TP CANAL S/W B G JQ151 LG-0TR127309AA TRANSISTOR KTA1273-TP-Y (KTA966A)KEC ABCDEFGH I JKLMNQ152 LG-0TR127309AA TRANSISTOR KTA1273-TP-Y (KTA966A)KEC ABCDEFGH I JKLMNQ154 LG-0TR126809BA TRANSISTOR,BIPOLARS KTA1268-BL TP KEC ABCDEFGH I JKLMNQ155 LG-0TR320509AB TRANSISTOR KTC3205-TP-Y (KTC2236A)KEC ABCDEFGH I JKLMNQ157 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ162 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ163 LG-0TR120109AC TRANSISTOR SRC1201 TP AUK TO92 4.7K,4.7K ABCDEFGH I JKLMNQ164 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ165 LG-0TR220309AF TRANSISTOR SRA2203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ166 LG-0TR127309AA TRANSISTOR KTA1273-TP-Y (KTA966A)KEC ABCDEFGH I JKLMNQ301 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ302 LG-0TR198009CA TRANSISTOR 2SA1980G TP AUK TO92 ABCDEFGH I JKLMNQ303 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ304 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ305 LG-0TR198009CA TRANSISTOR 2SA1980G TP AUK TO92 ABCDEFGH I JKLMNQ306 LG-0TR534409AA TRANSISTOR 2SC5344Y TP ABCDEFGH I JKLMNQ307 LG-0TR198009CA TRANSISTOR 2SA1980G TP AUK TO92 B DEFGH JQ308 LG-0TR198009CA TRANSISTOR 2SA1980G TP AUK TO92 ABCDEFGH I JKLMNQ309 LG-0TR198009CA TRANSISTOR 2SA1980G TP AUK TO92 ABCDEFGH I JKLMNQ501 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ502 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ503 LG-0TR127309AA TRANSISTOR KTA1273-TP-Y (KTA966A)KEC ABCDEFGH I JKLMNQ504 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ514 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ515 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ5P2 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ5P3 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ5P4 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ5P5 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ5S1 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMNQ7S1 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 FGQ901 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ902 LG-0TR220309AF TRANSISTOR SRA2203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ903 LG-0TR120309AE TRANSISTOR SRC1203 TP AUK TO92 22K,22K ABCDEFGH I JKLMNQ906 LG-0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ABCDEFGH I JKLMN
! BD101 S1WBA60 DIODE S1WBA60(1A 600V) SHIDENKEN ABCDEFGH I JKLMND102 EG01CW DIODE,RECTIFIER EG01CW(R-FORM 5MM) TP SANKEN ABCDEFGH I JKLMND103 LG-0DR180209AA DIODE,RECTIFIER ERA18-02KFRB TP FUJI DO204AL 2 ABCDEFGH I JKLMND104 1SS133DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND105 LG-0DR104009BA DIODE,RECTIFIER RL104F TP RECTRON NON 400V 1A ABCDEFGH I JKLMND106 1N5822DIODE,RECTIFIER 1N5822 BK RECTRON DO201AD 40V ABCDEFGH I JKLMND109 LG-0DR202000AB DIODE,RECTIFIER HER202 BK RECTRON NON 100V 2A ABCDEFGH I JKLMND155 LG-0DR104009AB DIODE,RECTIFIER RL104 R. TP GULF SEMICONDUCTOR ABCDEFGH I JKLMND156 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND159 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND160 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND301 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND502 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND509 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND901 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND902 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND903 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP ABCDEFGH I JKLMND904 1SS133 DIODE,SWITCHING 1SS133 DETECT,SW TP HZD151 MTZ13CT-77 DIODE,ZENERS MTZ13C TP ROHM-K ABCDEFGH I JKLMN
ZD503 LG-0DZ622609CA DIODE,ZENER GDZJ6.2C 26MM TP GRANDE DO34 0 ABCDEFGH I JKLMNZD801 UZ5.6BSB-T2 DIODE,ZENER UZ-5.6BSB 26MM TP PYUNG CHANG CDEF H MNZD802 UZ5.6BSB-T2 DIODE,ZENER UZ-5.6BSB 26MM TP PYUNG CHANG CDEF H MNZD803 MTZ13AT-77 DIODE,ZENER MTZ13A TP ROHM-K CDEF H MNZD804 MTZ13AT-77 DIODE,ZENER MTZ13A TP ROHM-K CDEF H MN
! C101 LG-624-088F CAPACITOR,DRAWING PCX2 275V 0.1UF,M (PILKO) ABCDEFGH I J ! C101 LG-624-088L CAPACITOR,DRAWING 435D SUNIL ELECTRONICS 0.1UF/2 KLMN ! C102 LG-624-088F CAPACITOR,DRAWING PCX2 275V 0.1UF,M (PILKO) ABCDEFGH I J ! C102 LG-624-088L CAPACITOR,DRAWING 435D SUNIL ELECTRONICS 0.1UF/2 KLMN
C103 LG-0CE476CU611 CAPACITOR,AL.ELECTROLYTIC 47UF SHL,SD 400V M FL BK7.5 ABCDEFGH I JKLMNC105 LG-0CQ1031Y519 CAPACITOR,POLYESTER 0.01UF D 630V K PE NI TP ABCDEFGH I JKLMNC106 LG-624-087B CAPACITOR HIGH-VOL 100P/1KV SMPS SAMHWA ABCDEFGH I JKLMNC109 QET41HM-106 CAPACITOR,FIXED ELECTROLYTIC 10M SRA 50V M FM5 TP(5) ABCDEFGH I JKLMN
! C112 LG-0CG3320U630 CAPACITOR,SEMI CERAMIC 3300 PF 400V M E R(NK,AD,SD) ABCDEFGH I JKLMN ! C113 LG-0CG1010U510 CAPACITOR,SEMI CERAMIC 100 PF 400V K B R (NK,AD,SD) ABCDEFGH I JKLMN
C114 LG-0CQ4732K409 CAPACITOR,FIXED FILM 0.047UF S 50V J PE TP ABCDEFGH I JKLMNC115 LG-624-085D CAPACITOR CE 47UF/50V KME (SMPS) ABCDEFGH I JKLMNC116 LG-0CE108BF630 CAPACITOR,FIXED ELECTROLYTIC 1000UF KME 16V M FM5 BULK ABCDEFGH I JKLMNC117 LG-624-082H CAPACITOR CE 1000UF/10V SHL(10*12.5)T/P ABCDEFGH I JKLMNC120 LG-0CE477BH630 CAPACITOR,AL.ELECTROLYTIC 470UF KME TYPE 25V M FM5 BULK ABCDEFGH I JKLMNC121 LG-0CE227CH618 CAPACITOR,FIXED ELECTROLYTIC 220UF SHL,SD 25V 20% FL TP 5 ABCDEFGH I JKLMNC127 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S ABCDEFGH I JKLMNC135 LG-0CN4710K518 CAPACITOR TUBULA(HIGH DIELE) 470P 50V K B TA26 ABCDEFGH I JKLMNC153 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC190 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC201 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 FGC202 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 FGC203 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) FGC204 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) FGC205 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA FGC206 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 FGC207 QET41HM-474 CAPACITOR,ELECTROLYTIC 0.47M SRA 50V M FM5 TP(5) FGC208 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 FGC209 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 FGC210 QET41HM-474 CAPACITOR,ELECTROLYTIC 0.47M SRA 50V M FM5 TP(5) FGC211 LG-0CN2220F668 CAPACITOR,TUBULAR(HIGH DIELEC) 2200P 16V M X TA26 FGC212 LG-0CN2220F668 CAPACITOR,TUBULAR(HIGH DIELEC) 2200P 16V M X TA26 FGC213 QET41HM-225 CAPACITOR,FIXED ELECTROLYTIC 2.2UF SRA,SS 50V 20% FM5 TP 5 FGC214 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 FGC215 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) FGC216 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 FGC301 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 ABCDEFGH I JKLMNC302 QET41CM-226 CAPACITOR,ELECTROLYTIC 22M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC303 LG-0CN1220F668 CAPACITOR TUBULA(HIGH DIELE) 1200P 16V M X TA26 ABCDEFGH I JKLMNC304 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC305 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC306 LG-0CN1220F668 CAPACITOR TUBULA(HIGH DIELE) 1200P 16V M X TA26 ABCDEFGH I JKLMNC307 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC308 LG-0CQ1532K409 CAPACITOR,FIXED FILM 0.015UF S 50V J PE TP ABCDEFGH I JKLMNC309 LG-0CN1210K518 CAPACITOR TUBULA(HIGH DIELE) 120P 50V K B TA26 ABCDEFGH I JKLMNC310 LG-0CQ1032K409 CAPACITOR,POLYESTER(MYLAR) 0.01UF S 50V J PE TP ABCDEFGH I JKLMNC311 LG-0CE4765K618 CAPACITOR,AL.ELECTROLYTIC 47UF SR,SV 50V M FL TP 5 ABCDEFGH I JKLMNC312 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC313 LG-0CQ2232L559 CAPACITOR,POLYESTER 0.022UF S 63V K PP NI TP5 ABCDEFGH I JKLMNC314 QET41CM-226 CAPACITOR,ELECTROLYTIC 22M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC315 LG-0CE2253K636 CAPACITOR,FIXED ELECTROLYTIC 2.2UF SRE,SE 50V 20% FM5 BP(D) ABCDEFGH I JKLMNC316 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC317 LG-0CN8220F668 CAPACITOR,TUBULAR(HIGH DIELEC) 8200P 16V M X TA26 ABCDEFGH I JKLMNC318 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC319 LG-0CQ1032K409 CAPACITOR,POLYESTER(MYLAR) 0.01UF S 50V J PE TP ABCDEFGH I JKLMNC320 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC321 LG-0CX6800K408 CAPACITOR TUBULA(T.C) 68P 50V J SL TA26 ABCDEFGH I JKLMNC322 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC323 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC324 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 ABCDEFGH I JKLMNC325 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC326 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC327 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC328 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC329 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC330 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC331 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC333 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC334 LG-0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V) ABCDEFGH I JKLMNC335 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC336 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC337 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC338 LG-0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V) ABCDEFGH I JKLMNC339 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC340 LG-0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V) ABCDEFGH I JKLMNC341 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S ABCDEFGH I JKLMNC342 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC343 LG-0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V) ABCDEFGH I JKLMN
MODEL MARK MODEL MARK MODEL MARKHR-J285EU A HR-J595MS F HR-J282EU KHR-J290EU B HR-J295MS G HR-J283EU LHR-J585EU C HR-J595EK H HR-J582EU MHR-J590EU D HR-J295EK I HR-J583EU NHR-J593EU E HR-J293EU J
# REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN # REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN
5-6
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------ ---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
MODEL MARK MODEL MARK MODEL MARKHR-J285EU A HR-J595MS F HR-J282EU KHR-J290EU B HR-J295MS G HR-J283EU LHR-J585EU C HR-J595EK H HR-J582EU MHR-J590EU D HR-J295EK I HR-J583EU NHR-J593EU E HR-J293EU J
C344 LG-0CN1010K518 CAPACITOR,TUBULAR(HIGH DIELEC) 100P 50V K B TA26 ABCDEFGH I JKLMNC345 LG-0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V) ABCDEFGH I JKLMNC346 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC347 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC348 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC349 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC353 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC355 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC356 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC357 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC358 LG-0CX6800K408 CAPACITOR TUBULA(T.C) 68P 50V J SL TA26 ABCDEFGH I JKLMNC359 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC360 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC361 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S ABCDEFGH I JKLMNC362 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC363 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC364 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC365 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC366 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC367 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC368 LG-0CQ8224K409 CAPACITOR,FIXED FILM 0.0082UF TE 50V 5% PE TP5 ABCDEFGH I JKLMNC369 LG-0CN1010K518 CAPACITOR,TUBULAR(HIGH DIELEC) 100P 50V K B TA26 ABCDEFGH I JKLMNC370 LG-0CN8200K419 CAPACITOR,FIXED TUBULAR(High d 82PF D 50V 5% B(Y5P) TA52 ABCDEFGH I JKLMNC371 LG-0CN8200K419 CAPACITOR,FIXED TUBULAR(High d 82PF D 50V 5% B(Y5P) TA52 ABCDEFGH I JKLMNC372 LG-0CN8200K419 CAPACITOR,FIXED TUBULAR(High d 82PF D 50V 5% B(Y5P) TA52 ABCDEFGH I JKLMNC373 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC375 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC500 LG-0CE4775C638 CAPACITOR,FIXED ELECTROLYTIC 470UF SR,SV 6.3V 20% FM5 TP 5 B DE JC500 LG-624-074A CAPACITOR SUPER CAP 0.047F/5.5V T/P S/S A C FGH I KLMNC501 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC502 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC503 QET40JM-227 CAPACITOR,ELECTROLYTIC 220M SRA 6.3V M FM5 TP(5) ABCDEFGH I JKLMNC504 QET40JM-227 CAPACITOR,ELECTROLYTIC 220M SRA 6.3V M FM5 TP(5) ABCDEFGH I JKLMNC505 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC506 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S ABCDEFGH I JKLMNC508 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC509 LG-0CC2200K415 CAPACITOR,CERAMIC(TEMP COMP) 22P 50V J NP0 TS ABCDEFGH I JKLMNC510 QET40JM-227 CAPACITOR,ELECTROLYTIC 220M SRA 6.3V M FM5 TP(5) ABCDEFGH I JKLMNC511 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC512 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC513 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC514 LG-0CC1200K415 CAPACITOR,CERAMIC(TEMP COMP) 12P 50V J NP0 TS ABCDEFGH I JKLMNC515 LG-0CC1500K415 CAPACITOR,CERAMIC(TEMP COMP) 15P 50V J NP0 TS ABCDEFGH I JKLMNC516 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S ABCDEFGH I JKLMNC518 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC519 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC520 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC523 QET41HM-225 CAPACITOR,FIXED ELECTROLYTIC 2.2UF SRA,SS 50V 20% FM5 TP 5 ABCDEFGH I JKLMNC524 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC525 QET40JM-227 CAPACITOR,ELECTROLYTIC 220M SRA 6.3V M FM5 TP(5) ABCDEFGH I JKLMNC526 LG-0CE4764J638 CAPACITOR,AL.ELECTROLYTIC 47UF SRA,SS 35V M FM5 TP 5 ABCDEFGH I JKLMNC527 LG-0CN2210K518 CAPACITOR TUBULA(HIGH DIELE) 220P 50V K B TA26 ABCDEFGH I JKLMNC533 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC534 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 ABCDEFGH I JKLMNC535 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 ABCDEFGH I JKLMNC543 LG-0CN2220F668 CAPACITOR,TUBULAR(HIGH DIELEC) 2200P 16V M X TA26 ABCDEFGH I JKLMNC544 LG-0CQ4732K409 CAPACITOR,FIXED FILM 0.047UF S 50V J PE TP ABCDEFGH I JKLMNC545 LG-0CN3330K518 CAPACITOR,FIXED TUBULAR(High d 0.033UF 50V K B TA26 ABCDEFGH I JKLMNC546 LG-0CE4764J638 CAPACITOR,AL.ELECTROLYTIC 47UF SRA,SS 35V M FM5 TP 5 ABCDEFGH I JKLMNC547 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC551 LG-0CQ3332K409 CAPACITOR,FIXED FILM 0.033UF S 50V J PE TP ABCDEFGH I JKLMNC552 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC561 QET40JM-227 CAPACITOR,ELECTROLYTIC 220M SRA 6.3V M FM5 TP(5) ABCDEFGH I JKLMNC564 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC567 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC570 LG-0CC1500K415 CAPACITOR,CERAMIC(TEMP COMP) 15P 50V J NP0 TS ABCDEFGH I JKLMNC571 LG-0CC1500K415 CAPACITOR,CERAMIC(TEMP COMP) 15P 50V J NP0 TS ABCDEFGH I JKLMNC575 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC576 LG-0CC2700K415 CAPACITOR CERAMIC(TEMP COMP) 27P 50V J NP0 TP ABCDEFGH I JKLMNC577 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S ABCDEFGH I JKLMNC578 LG-0CN2220F668 CAPACITOR,TUBULAR(HIGH DIELEC) 2200P 16V M X TA26 ABCDEFGH I JKLMNC581 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC582 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC583 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC589 LG-0CQ2232K409 CAPACITOR,FIXED FILM 0.022UF S 50V J PE TP ABCDEFGH I JKLMNC596 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC5A3 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC5A4 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC5A5 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC5G2 LG-0CE1086C638 CAPACITOR,FIXED ELECTROLYTIC 1000000000 PF SMS,SG 6.3V M FM ABCDEFGH I JKLMNC5G3 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC5K1 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC5P1 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMN
C5P2 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC5R1 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDEFGH I JKLMNC5R2 LG-0CN6810K518 CAPACITOR TUBULA(HIGH DIELE) 680P 50V K B TA26 ABCDEFGH I JKLMNC5S1 LG-0CX4300K408 CAPACITOR TUBULA(T.C) 43P 50V J SL TA26 ABCDEFGH I JKLMNC5S3 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S ABCDEFGH I JKLMNC701 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 ABCDEFGH I JKLMNC703 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) FGC704 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDEFGH I JKLMNC705 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC706 LG-0CE4775C618 CAPACITOR,AL.ELECTROLYTIC 470UF SR,SV 6.3V M FL TP 5 ABCDEFGH I JKLMNC707 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC710 LG-0CX6800K408 CAPACITOR TUBULA(T.C) 68P 50V J SL TA26 ABCDEFGH I JKLMNC711 LG-0CX3300K408 CAPACITOR TUBULA(T.C) 33P 50V J SL TA26 ABCDEFGH I JKLMNC712 LG-0CX5R60K508 CAPACITOR TUBULA(T.C) 5.6PF 50V K SL TA26 ABCDEFGH I JKLMNC713 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) ABCDE H I JKLMNC714 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDE H I JKLMNC751 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) CDEF H MNC752 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 CDEF H MNC753 LG-0CX5600K408 CAPACITOR,TUBULAR(T.C) 56P 50V J SL TA26 CDEF H MNC754 LG-0CX5600K408 CAPACITOR,TUBULAR(T.C) 56P 50V J SL TA26 CDEF H MNC755 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) CDEF H MNC756 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 CDEF H MNC757 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) CDEF H MNC758 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC759 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC760 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 CDEF H MNC761 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 CDEF H MNC764 LG-0CN1520F668 CAPACITOR,TUBULAR(HIGH DIELEC) 1500P 16V M X TA26 CDEF H MNC765 LG-0CN1520F668 CAPACITOR,TUBULAR(HIGH DIELEC) 1500P 16V M X TA26 CDEF H MNC766 QET41HM-335 CAPACITOR,FIXED ELECTROLYTIC 3.3UF SRA,SS 50V 20% FM5 TP 5 CDEF H MNC769 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC770 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC771 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 CDEF H MNC772 LG-0CC0500K015 CAPACITOR,CERAMIC(TEMP COMP) 5P 50V C NP0 TR CDEF H MNC773 LG-0CC0800K015 CAPACITOR CERAMIC(TEMP COMP) 8P 50V C NP0 TS CDEF H MNC790 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 ABCDEFGH I JKLMNC7M2 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) ABCDE H I JKLMNC7M3 LG-0CX2700K408 CAPACITOR TUBULA(T.C) 27P 50V J SL TA26 ABCDE H I JKLMNC7M6 LG-0CX2700K408 CAPACITOR TUBULA(T.C) 27P 50V J SL TA26 ABCDE H I JKLMNC7S1 QET41CM-336 CAPACITOR,ELECTROLYTIC 33M SRA 16V M FM5 TP(5) FGC7V1 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) B DE JC7V2 LG-0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S B DE JC7V3 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) B DE JC7V4 LG-0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V) B DE JC7V5 LG-0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V) B DE JC805 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA CDEF H MNC806 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 CDEF H MNC807 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 CDEF H MNC808 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA CDEF H MNC809 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA CDEF H MNC810 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC811 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC813 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC814 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC817 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC818 QET41HM-475 CAPACITOR,FIXED ELECTROLYTIC 4.7UF SRA,SS 50V 20% FM5 TP 5 CDEF H MNC819 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC820 LG-0CQ6822K409 CAPACITOR,POLYESTER(MYLAR) 6800PF S 50V J PE TP CDEF H MNC821 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) CDEF H MNC822 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC823 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC824 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC825 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) CDEF H MNC826 LG-0CQ6822K409 CAPACITOR,POLYESTER(MYLAR) 6800PF S 50V J PE TP CDEF H MNC827 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) CDEF H MNC828 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) CDEF H MNC829 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 CDEF H MNC830 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA CDEF H MNC831 LG-0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 CDEF H MNC832 QET41CM-476 CAPACITOR,ELECTROLYTIC 47M SRA/SS 16V M FM5 TP(5) CDEF H MNC835 QET41HM-474 CAPACITOR,ELECTROLYTIC 0.47M SRA 50V M FM5 TP(5) CDEF H MNC8R1 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 CDEF H MNC8R2 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 CDEF H MNC901 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 BCDEFGH J MNC902 LG-0CE477CF638 CAPACITOR,AL.ELECTROLYTIC 470UF SHL TYPE 16V M FM5 TP 5 ABCDEFGH I JKLMNC903 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC904 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 ABCDEFGH I JKLMNC908 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 A I KLC909 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC911 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 B DEFGH JC912 LG-0CE477CF638 CAPACITOR,AL.ELECTROLYTIC 470UF SHL TYPE 16V M FM5 TP 5 B DEFGH JC914 LG-0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V K B TA26 B DEFGH JC915 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA B DEFGH J
# REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN # REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN
5-7
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------ ---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
MODEL MARK MODEL MARK MODEL MARKHR-J285EU A HR-J595MS F HR-J282EU KHR-J290EU B HR-J295MS G HR-J283EU LHR-J585EU C HR-J595EK H HR-J582EU MHR-J590EU D HR-J295EK I HR-J583EU NHR-J593EU E HR-J293EU J
C917 LG-0CX2700K408 CAPACITOR TUBULA(T.C) 27P 50V J SL TA26 B DEFGH JC920 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC921 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC952 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA B G JC956 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) ABCDEFGH I JKLMNC957 LG-0CX2700K408 CAPACITOR TUBULA(T.C) 27P 50V J SL TA26 ABCDEFGH I JKLMNC960 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC961 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA ABCDEFGH I JKLMNC962 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) DEFC963 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) DEFC9A1 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) B G JC9A2 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) B G JC9A3 QET41HM-105 CAPACITOR,ELECTROLYTIC 1.0M SRA/SS50V M FM5 TP(5) B G JC9A4 LG-0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA B G JC9A5 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) B G JC9A6 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) B G JC9A7 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) B G JC9A8 QET41CM-106 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) B G JR101 LG-614-007A RESISTOR 2.7/2W CEMENT SMPS V ABCDEFGH I JKLMNR102 QRD161J-184Y RESISTOR,FIXED CARBON FILM 180K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR103 QRD161J-680Y RESISTOR,FIXED CARBON FILM 68 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR104 LG-0RS5602K619 RESISTOR,FIXED METAL OXIDE FIL 56K OHM 2 W 5.00% TR ABCDEFGH I JKLMNR105 LG-0RF0101A619 RESISTOR,DRAWING 1 OHM 1/2 W(7.0) 5.00% TR ABCDEFGH I JKLMNR106 QRD161J-184Y RESISTOR,FIXED CARBON FILM 180K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR109 LG-0RS0350K619 RESISTOR,FIXED METAL OXIDE FIL 0.35 OHM 2 W 5.00% TR ABCDEFGH I JKLMNR112 QRD161J-104Y RESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR116 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR117 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR118 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR119 LG-0RN3301F408 RESISTOR,FIXED METAL FILM 3.3K OHM 1/6 W 1.00% TA26 ABCDEFGH I JKLMNR120 LG-0RN3001F408 RESISTOR,FIXED METAL FILM 3K OHM 1/6 W 1.00% TA26 ABCDEFGH I JKLMNR125 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR126 QRD161J-681Y RESISTOR,FIXED CARBON FILM 680 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR151 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR152 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR153 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR154 QRD161J-331Y RESISTOR,FIXED CARBON FILM 330 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR155 QRD161J-332Y RESISTOR,FIXED CARBON FILM 3.3K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR157 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR158 QRD161J-183Y RESISTOR,FIXED CARBON FILM 18K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR159 QRD161J-471Y RESISTOR,FIXED CARBON FILM 470 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR161 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR170 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR172 QRD161J-271Y RESISTOR,FIXED CARBON FILM 270 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR173 QRD161J-271Y RESISTOR,FIXED CARBON FILM 270 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR201 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 FGR202 QRD161J-124Y RESISTOR,FIXED CARBON FILM 120K OHM 1/6 W 5.00% TA26 FGR204 QRD161J-473Y RESISTOR,FIXED CARBON FILM 47K OHM 1/6 W 5.00% TA26 FGR301 QRD161J-563Y RESISTOR,FIXED CARBON FILM 56K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR303 QRD161J-183Y RESISTOR,FIXED CARBON FILM 18K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR304 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR305 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR306 QRD161J-223Y RESISTOR,FIXED CARBON FILM 22K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR307 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR308 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR309 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR310 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR311 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR312 QRD161J-683Y RESISTOR,FIXED CARBON FILM 68K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR313 QRD161J-2R2 RESISTOR,FIXED CARBON FILM 2.2 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR314 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR315 QRD161J-470Y RESISTOR,FIXED CARBON FILM 47 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR316 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR317 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR318 QRD161J-392Y RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR319 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR320 QRD161J-151Y RESISTOR,FIXED CARBON FILM 150 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR321 QRD161J-122Y RESISTOR,FIXED CARBON FILM 1.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR322 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR323 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR324 QRD161J-334Y RESISTOR,FIXED CARBON FILM 330K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR325 QRD161J-471Y RESISTOR,FIXED CARBON FILM 470 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR326 QRD161J-123Y RESISTOR,FIXED CARBON FILM 12K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR327 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR328 QRD161J-271Y RESISTOR,FIXED CARBON FILM 270 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR329 QRD161J-123Y RESISTOR,FIXED CARBON FILM 12K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR330 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR331 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR334 QRD161J-272Y RESISTOR,FIXED CARBON FILM 2.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR335 QRD161J-682Y RESISTOR,FIXED CARBON FILM 6.8K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR336 QRD161J-104Y RESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR337 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR338 QRD161J-271Y RESISTOR,FIXED CARBON FILM 270 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMN
R339 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR340 QRD161J-183Y RESISTOR,FIXED CARBON FILM 18K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR341 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR342 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR343 QRD161J-750Y RESISTOR,FIXED CARBON FILM 75 OHM 1/6 W 5.00% TA26 B DEFGH JR344 QRD161J-471Y RESISTOR,FIXED CARBON FILM 470 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR345 QRD161J-471Y RESISTOR,FIXED CARBON FILM 470 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR346 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR347 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 B DEFGH JR349 QRD161J-182Y RESISTOR,FIXED CARBON FILM 1.8K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR350 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR351 QRD161J-824Y RESISTOR,FIXED CARBON FILM 820K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR3A1 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR501 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR502 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR503 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR504 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR505 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR506 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR507 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR508 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR509 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR510 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR511 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR512 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR513 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR514 QRD161J-124Y RESISTOR,FIXED CARBON FILM 120K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR515 QRD161J-271Y RESISTOR,FIXED CARBON FILM 270 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR516 QRD161J-474Y RESISTOR,FIXED CARBON FILM 470K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR517 QRD161J-471Y RESISTOR,FIXED CARBON FILM 470 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR518 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR520 QRD161J-392Y RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR521 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR522 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR523 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR524 QRD161J-220Y RESISTOR,FIXED CARBON FILM 22 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR525 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR526 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR527 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR528 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR529 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR530 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR531 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR535 QRD161J-474Y RESISTOR,FIXED CARBON FILM 470K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR542 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR543 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR544 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR546 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR547 QRD161J-123Y RESISTOR,FIXED CARBON FILM 12K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR548 QRD161J-104Y RESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR550 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR553 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR555 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR556 QRD161J-223Y RESISTOR,FIXED CARBON FILM 22K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR557 QRD161J-273Y RESISTOR,FIXED CARBON FILM 27K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR558 QRD161J-223Y RESISTOR,FIXED CARBON FILM 22K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR559 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR560 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR561 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR562 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR563 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR564 QRD161J-273Y RESISTOR,FIXED CARBON FILM 27K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR566 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR567 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR568 QRD161J-683Y RESISTOR,FIXED CARBON FILM 68K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR569 QRD161J-105Y RESISTOR,FIXED CARBON FILM 1M OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR570 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR575 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR576 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR577 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR578 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR579 QRD161J-563Y RESISTOR,FIXED CARBON FILM 56K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR582 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR583 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR589 QRD161J-105Y RESISTOR,FIXED CARBON FILM 1M OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR591 QRD161J-104Y RESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5A2 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5A3 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5A5 QRD161J-474Y RESISTOR,FIXED CARBON FILM 470K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5B3 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5B4 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5B5 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5C1 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMN
# REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN # REF No. PART No. PART NAME, DESCRIPTION SPECIFICATION ABCDEFGH I JKLMN
5-8
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------ ---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
(VP)-V15 E. & O. E. No.82915
MODEL MARK MODEL MARK MODEL MARKHR-J285EU A HR-J595MS F HR-J282EU KHR-J290EU B HR-J295MS G HR-J283EU LHR-J585EU C HR-J595EK H HR-J582EU MHR-J590EU D HR-J295EK I HR-J583EU NHR-J593EU E HR-J293EU J
R5C5 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5C6 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5C7 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5C9 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5P2 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5P3 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5R2 QRD161J-331Y RESISTOR,FIXED CARBON FILM 330 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5R3 QRD161J-331Y RESISTOR,FIXED CARBON FILM 330 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5R4 QRD161J-331Y RESISTOR,FIXED CARBON FILM 330 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5R5 QRD161J-331Y RESISTOR,FIXED CARBON FILM 330 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5R7 QRD161J-331Y RESISTOR,FIXED CARBON FILM 330 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5R8 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5S1 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T1 QRD161J-182Y RESISTOR,FIXED CARBON FILM 1.8K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T2 QRD161J-152Y RESISTOR,FIXED CARBON FILM 1.5K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T3 QRD161J-222Y RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T4 QRD161J-272Y RESISTOR,FIXED CARBON FILM 2.7K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T5 QRD161J-392Y RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T9 QRD161J-182Y RESISTOR,FIXED CARBON FILM 1.8K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T10 QRD161J-152Y RESISTOR,FIXED CARBON FILM 1.5K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR5T11 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR706 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR707 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR709 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR753 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 CDEF H MNR754 QRD161J-332Y RESISTOR,FIXED CARBON FILM 3.3K OHM 1/6 W 5.00% TA26 CDEF H MNR755 QRD161J-332Y RESISTOR,FIXED CARBON FILM 3.3K OHM 1/6 W 5.00% TA26 CDEF H MNR758 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 CDEF H MNR759 QRD161J-562Y RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5.00% TA26 CDEF H MNR7M1 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDE H I JKLMNR7M2 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDE H I JKLMNR7M3 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDE H I JKLMNR7M5 QRD161J-221Y RESISTOR,FIXED CARBON FILM 220 OHM 1/6 W 5.00% TA26 ABCDE H I JKLMNR7S1 QRD161J-223Y RESISTOR,FIXED CARBON FILM 22K OHM 1/6 W 5.00% TA26 FGR7V1 QRD161J-105Y RESISTOR,FIXED CARBON FILM 1M OHM 1/6 W 5.00% TA26 B DE JR7V2 QRD161J-104Y RESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26 B DE JR7V3 QRD161J-682Y RESISTOR,FIXED CARBON FILM 6.8K OHM 1/6 W 5.00% TA26 B DE JR7V4 QRD161J-564Y RESISTOR,FIXED CARBON FILM 560K OHM 1/6 W 5.00% TA26 B DE JR7V5 QRD161J-682Y RESISTOR,FIXED CARBON FILM 6.8K OHM 1/6 W 5.00% TA26 B DE JR7V6 QRD161J-564Y RESISTOR,FIXED CARBON FILM 560K OHM 1/6 W 5.00% TA26 B DE JR7V7 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 B DE JR7V8 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 B DE JR7V9 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 B DE JR801 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 CDEF H MNR802 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 CDEF H MNR817 QRD161J-335Y RESISTOR,FIXED CARBON FILM 3.3M OHM 1/6 W 5.00% TA26 CDEF H MNR818 QRD161J-333Y RESISTOR,FIXED CARBON FILM 33K OHM 1/6 W 5.00% TA26 CDEF H MNR819 QRD161J-272Y RESISTOR,FIXED CARBON FILM 2.7K OHM 1/6 W 5.00% TA26 CDEF H MNR820 QRD161J-393Y RESISTOR,FIXED CARBON FILM 39K OHM 1/6 W 5.00% TA26 CDEF H MNR821 QRD161J-272Y RESISTOR,FIXED CARBON FILM 2.7K OHM 1/6 W 5.00% TA26 CDEF H MNR822 QRD161J-333Y RESISTOR,FIXED CARBON FILM 33K OHM 1/6 W 5.00% TA26 CDEF H MNR823 QRD161J-471Y RESISTOR,FIXED CARBON FILM 470 OHM 1/6 W 5.00% TA26 CDEF H MNR824 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 CDEF H MNR825 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 CDEF H MNR826 QRD161J-182Y RESISTOR,FIXED CARBON FILM 1.8K OHM 1/6 W 5.00% TA26 CDEF H MNR827 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 CDEF H MNR828 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 CDEF H MNR830 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 CDEF H MNR831 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 CDEF H MNR8R1 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 CDEF H MNR8R2 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 CDEF H MNR901 QRD161J-750Y RESISTOR,FIXED CARBON FILM 75 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR902 QRD161J-750Y RESISTOR,FIXED CARBON FILM 75 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR903 QRD161J-392Y RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5.00% TA26 A I KLR903 QRD161J-472Y RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5.00% TA26 BCDEFGH J MNR904 QRD161J-473Y RESISTOR,FIXED CARBON FILM 47K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR905 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR906 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR911 QRD161J-750Y RESISTOR,FIXED CARBON FILM 75 OHM 1/6 W 5.00% TA26 B DEFGH JR912 QRD161J-750Y RESISTOR,FIXED CARBON FILM 75 OHM 1/6 W 5.00% TA26 B DEFGH JR913 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 B DEFGH JR914 QRD161J-561Y RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5.00% TA26 B DEFGH JR943 QRD161J-152Y RESISTOR,FIXED CARBON FILM 1.5K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR962 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 B G JR963 QRD161J-101Y RESISTOR,FIXED CARBON FILM 100 OHM 1/6 W 5.00% TA26 B G JR964 QRD161J-821Y RESISTOR,FIXED CARBON FILM 820 OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR965 QRD161J-102Y RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5.00% TA26 ABCDEFGH I JKLMNR9C1 QRD161J-123Y RESISTOR,FIXED CARBON FILM 12K OHM 1/6 W 5.00% TA26 B DEFG JR9C2 QRD161J-103Y RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5.00% TA26 B DEFG JR9M3 QRD161J-473Y RESISTOR,FIXED CARBON FILM 47K OHM 1/6 W 5.00% TA26 A I KLR9M4 QRD161J-392Y RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5.00% TA26 A I KLFL301 LG-633-032K COIL,IFT BIAC OSC,1CHIP 5V(KS-75M) KWAN ABCDEFGH I JKLMNL101 LG-636-004C COIL BEAD CORE BFS3550R2FD8,R T/P ABCDEFGH I JKLMN
! L102 LG-616-145H FILTER(CIRC) SHT LFS2020V4-04350 ABCDEFGH I JKLMNL103 LG-633-088G COIL,CHOKE CHOCK(22MH) 5MM TOKO TP ABCDEFGH I JKLMNL104 LG-633-088G COIL,CHOKE CHOCK(22MH) 5MM TOKO TP ABCDEFGH I JKLMNL106 LG-636-004C COIL BEAD CORE BFS3550R2FD8,R T/P ABCDEFGH I JKLMNL201 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP FGL301 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 ABCDEFGH I JKLMNL302 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP ABCDEFGH I JKLMNL303 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 ABCDEFGH I JKLMNL304 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 ABCDEFGH I JKLMNL305 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP ABCDEFGH I JKLMNL307 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 ABCDEFGH I JKLMNL501 LG-0LA0122K018 INDUCTOR AXIAL LEAD 12M K 2.3X3.4 L5 TP ABCDEFGH I JKLMNL503 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP ABCDEFGH I JKLMNL504 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 ABCDEFGH I JKLMNL505 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP ABCDEFGH I JKLMNL506 LG-635-027C INDUCTOR,RADIAL LEAD EL0405RA SKI150G-3 K-TDK 15UH ABCDEFGH I JKLMNL5G2 LG-0LR3300K035 INDUCTOR RADIAL LEAD 330M K 6X6 L5 TP ABCDEFGH I JKLMNL5S1 LG-0LA0332K018 INDUCTOR AXIAL LEAD 33M K 2.3X3.4 L5 TP ABCDEFGH I JKLMNL702 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP ABCDEFGH I JKLMNL703 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP ABCDEFGH I JKLMNL704 LG-0LA0821K018 INDUCTOR AXIAL LEAD 8.2M K 2.3X3.4 L5 TP ABCDEFGH I JKLMNL705 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP ABCDE H I JKLMNL751 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 CDEF H MNL753 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 CDEF H MNL7V1 LG-0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP B DE JL801 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 CDEF H MNL802 LG-0LR0102J0N5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 CDEF H MNL8R1 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP CDEF H MNL8R2 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP CDEF H MNL901 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP ABCDEFGH I JKLMNL902 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP ABCDEFGH I JKLMNL904 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP ABCDEFGH I JKLMNL905 LG-636-004C COIL BEAD CORE BFS3550R2FD8,R T/P ABCDEFGH I JKLMNL906 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP ABCDEFGH I JKLMNL907 LG-636-004C COIL BEAD CORE BFS3550R2FD8,R T/P ABCDEFGH I JKLMNL911 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP B DEFGH JL912 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP B DEFGH JL914 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP B DEFGH JL915 LG-0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP B DEFGH JCS501 LG-6600M000002 SWITCH,PUSH MPU11810MLB0 MIC DC 5V 1MA D-3 ABCDEFGH I JKLMNES501 LG-4931R-0050C HOLDER ASSEMBLY END (DI) ABCDEFGH I JKLMNES502 LG-4931R-0050C HOLDER ASSEMBLY END (DI) ABCDEFGH I JKLMN
! F101 LG-585-011T FUSE,SLOW BLOW 1600MA 250 V 5.2X20 CY/GL SEMK ABCDEFGH I JKLMN ! FH01 LG-586-008B HOLDER FUSE CLIP TP SINSUNG ABCDEFGH I JKLMN ! FH02 LG-586-008B HOLDER FUSE CLIP TP SINSUNG ABCDEFGH I JKLMN
JK801 LG-6612R-C002C JACK,RCA RCA-208C-06 YUQIU WH-RD CDEF H MNJK901 LG-6620RM0002J JACK,SCART DSAM-0121 DOOWON 2F-21P(BL-BK) B DEFG JJK901 LG-6620RM0002K JACK,SCART DSAM-0120 DOOWON 1F-21P (BK) A C I KLMNJK901 LG-6620RM0002L JACK,SCART DSAM-0139 DOOWON 2F-21P(BK-BK) HLD501 LG-4931R-0017C HOLDER ASSY LED(DI-CKD)LOCAL ABCDEFGH I JKLMNLED502 LG-6301R2U001F LED ASSEMBLY TOH-30M-G3R1 OASIS UNIVERSAL 4 ABCDEFGH I JKLMNMS501 LG-6600JB8005B SWITCH,MODE NON 5V 1MA VERTICAL -G ABCDEFGH I JKLMNP3D01 LG-561-234S CONNECTOR(CIRC),DRAWING GF120-9S-TS-A LG CABLE 9P 1.25 CDEF H MNP3D01 LG-561-234Z CONNECTOR (CIRC) GF120-3S-TS-A LGC 3PIN 1.25MM AB G I JKLP3D02 LG-6630R5S010A CONNECTOR (CIRC) GF105-06S-TS LG CABLE 6PIN 2MM ABCDEFGH I JKLMNP3D03 LG-561-251B CONNECTOR(CIRC),DRAWING GB201-2P-TS-B(LGC) ABCDEFGH I JKLMNPMC01 LG-6630R-BE01L CONNECTOR (CIRC),BOARD TO BOARJE612-12 JAE EUN 12P 2.0MM ABCDEFGH I JKLMN
! PW101 LG-561-292B CONNECTOR GP390 LGC 3P 3.96 STRAIGHT SN ABCDEFGH I JKLMNRC501 LG-6712R1940GA REMOTE CONTROLLER RECEIVER TSOP2840WE1 VISHAY(TEMIC) 40KH ABCDEFGH I JKLMNRS501 LG-6500RAB003A SENSOR SG-260 KODENSHI D33 REEL SENSO ABCDEFGH I JKLMNRS502 LG-6500RAB003A SENSOR SG-260 KODENSHI D33 REEL SENSO ABCDEFGH I JKLMNSW5T1 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T10 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T11 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T12 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T13 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T3 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T4 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T5 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMNSW5T6 LG-556-213C SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 ABCDEFGH I JKLMN
! T101 LG-642-015G TRANSFORMER,SMPS SJE-015G/SHT-015G SJ/SH/CS/LSE ABCDEFGH I JKLMNTU701 LG-6700PFPL03A TUNER SECAM TADC-S301D LG PAL FS Y2K FGTU701 LG-6700PFPL03B TUNER B/G TADC-G301D LG PAL FS Y2K2 AB JTU701 LG-6700PFPL03E TUNER G/K/I TADC-M301D LG PAL FS Y2 CDE H I KLMNX301 LG-6202R2443AC RESONATOR,CRYSTAL HC49U BUBANG 4-433709MHZ 15 ABCDEFGH I JKLMNX501 LG-6212AA2100C RESONATOR,CRYSTAL HC-49S BUBANG 10MHZ +/- 30 PPM ABCDEFGH I JKLMNX502 LG-6202R-DA01A RESONATOR,CRYSTAL CFS-308 CITIZEN 32-768KHZ ABCDEFGH I JKLMNX751 LG-529-021Q RESONATOR,CRYSTAL 49U BUBANG 18432000HZ 30PPM 16 CDEF H MN