service manual us model - diagramas dediagramas.diagramasde.com/otros/cdx-s2210x.pdfservice manual...

1

Ver. 1.3 2005. 11

Model Name Using Similar Mechanism NEW

CD Drive Mechanism Type MG-611TA-186//K

Optical Pick-up Name KSS1000E

SERVICE MANUAL US ModelCDX-S2210/SW330

Canadian ModelCDX-S2210

E ModelCDX-S2210S/S2210X

East European ModelCDX-S2250EE

CDX-S2210/S2210S/S2210X/S2250EE/SW330

AUDIO POWER SPECIFICATIONS (US Model)POWER OUTPUT AND TOTAL HARMONIC DISTORTION23.2 watts per channel minimum continuous average power into4 ohms, 4 channels driven from 20 Hz to 20 kHz with no morethan 5% total harmonic distortion.

CD player sectionSignal-to-noise ratio 120 dBFrequency response 10 – 20,000 HzWow and flutter Below measurable limit

Tuner sectionFMTuning range US, Canadian Model:

87.5 – 107.9 MHzE model:FM tuning interval:50 kHz/200 kHzswitchable87.5 – 108 MHz (at 50 kHz step)87.5 – 107.9 MHz (at 200 kHz step)East European Model:FM1/FM2: 87.5 – 108.0 MHz (at 50 kHz step)FM3: 65 – 74 MHz (at 30 kHz step)

Antenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzUsable sensitivity 9 dBfSelectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo),

69 dB (mono)Harmonic distortion at 1 kHz

0.5% (stereo),0.3% (mono)

Separation 35 dB at 1 kHzFrequency response 30 – 15,000 Hz

SPECIFICATIONSAMTuning range US, Canadian Model:

530 – 1,710 kHzE Model:AM tuning interval:9 kHz/10 kHz switchable531 – 1,602 kHz (at 9 kHz step)530 – 1,710 kHz (at 10 kHz step)East European Model:531 – 1,602 kHz

Antenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzSensitivity 30 µV

Power amplifier sectionOutputs Speaker outputs

(sure seal connectors)Speaker impedance 4 – 8 ohmsMaximum power output Except East European model:

52 W × 4 (at 4 ohms)East European model:50 W × 4 (at 4 ohms)

GeneralOutputs Audio outputs terminal (sub/rear switchable)

Power antenna relay control terminalPower amplifier control terminal

Inputs Antenna input terminalRemote controller input terminal (CDX-S2210C only)

• The tuner and CD sections have no adjustments.

Sony CorporationeVehicle Division

Published by Sony Engineering Corporation

9-879-323-042005K04-1

© 2005. 11

– Continued on next page –

FM/AM COMPACT DISC PLAYER

Photo: CDX-S2250EE

2

CDX-S2210/S2210S/S2210X/S2250EE/SW330

If the optical pick-up block is defective, please replace the wholeoptical pick-up block.Never turn the semi-fixed resistor located at the side of opticalpick-up block.

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCESSONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCESSONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUELOU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

Tone controls Low: ±10 dB at 60 Hz (XPLOD)Mid: ±10 dB at 1 kHz (XPLOD)High: ±10 dB at 10 kHz (XPLOD)

Power requirements 12 V DC car battery(negative ground)

Dimensions Approx. 178 × 50 × 178 mm(7 1/8 × 2 × 7 1/8 in.) (w/h/d)

Mounting dimensions Approx. 182 × 53 × 161 mm(7 1/4 × 2 1/8 × 6 3/8 in.) (w/h/d)

Mass Approx. 1.2 kg(2 lb. 10 oz.)

Supplied accessories Card remote commander: RM-X151 (CDX-S2210S/SW330only) Parts for installation and connections (1 set)Front panel case (1)

Design and specifications are subject to change withoutnotice.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and also usethe procedure in the printed matter which is included in the repairparts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, ob-serve from more than 30 cm away from the objective lens.

Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

TEST DISCSThis set can playback CD-R and CD-ROM discs. The followingtest discs should be used to check the capability:

CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)CD-RW test disc TCD-W082L (Part No. J-2502-063-2)

SERVICE NOTES

• E, East European Model

This label is located on the bottom of the chassis.

optical pick-up

semi-fixed resistor

3

z UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!

• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

CDX-S2210/S2210S/S2210X/S2250EE/SW330

• CD Playback:You can play CD-DA (also containing CD TEXT*1), CD-R/CD-RW (MP3 files also containing Multi Session and ATRAC CD(ATRAC3 and ATRAC3plus format).

Type of discs Label on the disc

CD-DA

MP3

ATRAC CD

*1 A CD TEXT disc is a CD-DA that includes information such asdisc, artist and track name.

EXTENSION CABLE AND SERVICE POSITIONWhen repairing or servicing this set, connect the jig (extension cable)as shown below.

• Connect the MAIN board (CNP301) and the SERVO board (CN2)with the extension cable (Part No. J-2502-076-1).

SERVO BOARDCN2

MAIN BOARDCNP301

J-2502-076-1

4

CDX-S2210/S2210S/S2210X/S2250EE/SW330

TABLE OF CONTENTS

1. GENERALLocation of controls and basic operations (CDX-S2210) ....... 5Location of controls and basic operations (CDX-S2250EE) .. 5Location of controls and basic operations(CDX-S2210S/S2210X) .......................................................... 5Location of controls and basic operations (CDX-SW330) ..... 6Connections (CDX-S2210) ..................................................... 7Connections (CDX-S2210S/S2210X) ..................................... 8Connections (CDX-S2250EE) ................................................ 9Connections (CDX-SW330) .................................................. 10

2. DISASSEMBLY2-1. Sub Panel (LCD) Assy ...................................................... 112-2. CD Mechanism Block ....................................................... 122-3. Main Board ....................................................................... 122-4. Chassis (T) Sub Assy ........................................................ 132-5. Roller Arm Assy ................................................................ 132-6. Chassis (OP) Assy ............................................................. 142-7. Optical Pick-up ................................................................. 142-8. SL Motor Assy (M902) ..................................................... 152-9. LE Motor Assy (M903) ..................................................... 152-10. Servo Board ....................................................................... 16

3. DIAGRAMS3-1. Block Diagram –CD Section– ........................................... 173-2. Block Diagram –Main Section– ........................................ 183-3. Block Diagram –Display Section– .................................... 193-4. Printed Wiring Boards –SERVO Board– .......................... 213-5. Schematic Diagram –SERVO Board (1/2)– ...................... 223-6. Schematic Diagram –SERVO Board (2/2)– ...................... 233-7. Printed Wiring Board –Main Board– ................................ 243-8. Schematic Diagram –Main Board (1/4)– .......................... 253-9. Schematic Diagram –Main Board (2/4)– .......................... 263-10. Schematic Diagram –Main Board (3/4)– .......................... 273-11. Schematic Diagram –Main Board (4/4)– .......................... 283-12. Printed Wiring Board –KEY Board– ................................ 293-13. Schematic Diagram –KEY Board– ................................... 30

4. EXPLODED VIEWS4-1. Main Section ..................................................................... 394-2. Front Panel Section ........................................................... 404-3. CD Mechanism Section (1) (MG-611TA-186//K) ............ 414-4. CD Mechanism Section (2) (MG-611TA-186//K) ............ 424-5. CD Mechanism Section (3) (MG-611TA-186//K) ............ 434-6. CD Mechanism Section (4) (MG-611TA-186//K) ............ 44

5. ELECTRICAL PARTS LIST ......................................... 45

5

CDX-S2210/S2210S/S2210X/S2250EE/SW330

Location of controls and basic operations

Main unit

Refer to the pages listed for details.

a Volume +/– buttonTo adjust volume.

b SEL (select) button 4, 7To select items.

c SOURCE buttonTo power on/change the source (Radio/CD).

d MODE button 6To select the radio band (FM/AM).

e Disc slotInsert the disc (label side up), playback starts.

f Display windowg ATT (attenuate) button

To attenuate the sound. To cancel, press again.

h EQ3 (equalizer) button 7To select an equalizer type (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM or OFF).

i Z (eject) buttonTo eject the disc.

j SEEK +/– buttonRadio:To tune in stations automatically (press); find a station manually (press and hold).CD:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); fast-forward/reverse a track (press and hold).

k (front panel release) button 4

l DSPL (display)/DIM (dimmer) button 4To change display items (press); change the display brightness (press and hold).

m SENS buttonTo improve weak reception: LOCAL/MONO.

n RESET button (located behind the front panel) 4

o Number buttonsRadio:To receive stored stations (press); store stations (press and hold).CD:(1)/(2): GROUP* –/+To skip groups (press); skip groups continuously (press and hold).(3): REP 6(4): SHUF 6

p BTM button 6To start the BTM function (press and hold).

q OFF buttonTo power off/stop the source.

r Receptor for the card remote commander 8

* When an MP3/ATRAC CD is played.

SENS BTM OFFDSPL 1 2 3 4 5 6

SEL

DIM SHUFREP

EQ3ATTSOURCE MODE SEEK

CDX-S2250EE

– +GROUP

qa

1 2 3 4 5 6 7 8 9 0

qs qd qg qh qj qkqf


Main unit

Refer to the pages listed for details.











k (front panel release) button 4

l DSPL (display)/DIM (dimmer) button 4, 6To change display items (press); change the display brightness (press and hold).






r Receptor for the card remote commander 8



SEL

DIM SHUFREP


CDX-S2210

– +GROUP

qa

1 2 3 4 5 6 7 8 9 0

qs qd qg qh qj qkqf


Main unit

Card remote commander RM-X151(CDX-S2210S only)

)


SEL

DIM SHUFREP


CDX-S2210XCDX-S2210SCDX-S2210C

– +GROUP

qa

1 2 3 4 5 6 7 8 9 0

qs qd qg qh qj qkqf ql


SEL

DIM SHUFREP


CDX-S2210XCDX-S2210SCDX-S2210C

– +GROUP

qa

1 2 3 4 5 6 7 8 9 0

qs qd qg qh qj qkqf ql

OFF

DSPL SCRL

SELSOURCE MODE

1 32

4 65

ATT

VOL+

–

+

–

7

qs

qk

342

wd

w;

wa

wf

ws

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.











k (front panel release) button 4l DSPL (display)/DIM (dimmer) button

4, 8To change display items (press); change the display brightness (press and hold).



o Frequency select switch (located on the bottom of the unit)See “Frequency select switch” in the supplied installation/connections manual.

p Number buttonsRadio:To receive stored stations (press); store stations (press and hold).CD:(1)/(2): GROUP* –/+To skip groups (press); skip groups continuously (press and hold).(3): REP 8(4): SHUF 8

q BTM button 8To start the BTM function (press and hold).

r OFF buttonTo power off/stop the source.

s Receptor for the card remote commander 10

The following buttons on the card remote commander have also different buttons/functions from the unit.

t < (.)/, (>) buttonsTo control radio/CD, the same as (SEEK) +/– on the unit. (For details of other operations, see “With the card remote commander” on each pages.)

u VOL +/– buttonTo adjust volume.

v M (+)/m (–) buttonsTo control CD, the same as (1)/(2) –/+ on the unit. (For details of other operations, see “With the card remote commander” on each pages.)

w SCRL buttonTo scroll the display item.

x Number buttonsTo receive stored stations (press); store stations (press and hold).


NoteIf the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 13.

SECTION 1GENERAL This section is extracted

from instruction manual.

(CDX-S2210) (CDX-S2250EE)

(CDX-S2210S/S2210X)

6

CDX-S2210/S2210S/S2210X/S2250EE/SW330


Main unit

Card remote commander RM-X151


SEL

DIM SHUFREP


CDX-SW330

– +GROUP

qa

1 2 3 4 5 6 7 8 9 0

qs qd qg qh qjqf qk

OFF

DSPL SCRL

SELSOURCE MODE

1 32

4 65

ATT

VOL+

–

+

–

7

qs

qj

342

ws

ql

w;

wd

wa

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.


b SEL (select) button 4, 9, 9, 9To select items.









k (front panel release) button 4l DSPL (display)/DIM (dimmer) button

4, 8To change display items (press); change the display brightness (press and hold).






r Receptor for the card remote commander

The following buttons on the card remote commander have also different buttons/functions from the unit.

s < (.)/, (>) buttonsTo control radio/CD, the same as (SEEK) +/– on the unit. (For details of other operations, see “With the card remote commander” on each pages.)

t VOL +/– buttonTo adjust volume.

u M (+)/m (–) buttonsTo control CD, the same as (1)/(2) –/+ on the unit. (For details of other operations, see “With the card remote commander” on each pages.)

v SCRL buttonTo scroll the display item.

w Number buttonsTo receive stored stations (press); store stations (press and hold).


NoteIf the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 11.

(CDX-SW330)

7

CDX-S2210/S2210S/S2210X/S2250EE/SW330

Connections (CDX-S2210)

BUSAUDIO

IN

L

R

AUDIOOUT

L

R

AUDIO OUT REAR*2

2

4

5

1

3

Schéma de raccordement (3)1 À un point métallique de la voiture

Branchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’entrée d’alimentation jaune et rouge.

2 Vers le câble de commande d’antenne électrique ou le câble d’alimentation de l’amplifi cateur d’antenneRemarques• Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas

d’antenne électrique ni d’amplifi cateur d’antenne, ou avec une antenne télescopique manuelle.

• Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».

3 Au niveau de AMP REMOTE IN de l’amplifi cateur de puissance en optionCe raccordement s’applique uniquement aux amplifi cateurs. Le branchement de tout autre système risque d’endommager l’appareil.

4 À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoiresRemarques• S’il n’y a pas de position accessoires, raccordez la borne

d’alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.


5 À la borne +12 V qui est alimentée en permanenceRaccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.

Connection diagram (3)1 To a metal surface of the car

First connect the black ground lead, then connect the yellow and red power input leads.

2 To the power antenna control lead or power supply lead of antenna booster amplifi erNotes• It is not necessary to connect this lead if there is no power

antenna or antenna booster, or with a manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

3 To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.

4 To the +12 V power terminal which is energized in the accessory position of the ignition key switchNotes• If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal

surface of the car fi rst.• When your car has a built-in FM/AM antenna in the rear/

side glass, see “Notes on the control and power supply leads.”

5 To the +12 V power terminal which is energized at all timesBe sure to connect the black ground lead to a metal surface of the car fi rst.

AMP REM

Max. supply current 0.3 ACourant max. fourni 0,3 A

Fuse (10 A)Fusible (10 A)

Blue/white stripedRayé bleu/blanc

from car antenna à partir de l’antenne de la voiture

ANT REM

2

*1

RedRouge

YellowJaune

BlackNoir

BlueBleu

WhiteBlanc

GreenVert

PurpleMauve

White/black stripedRayé blanc/noir

Gray/black stripedRayé gris/noir

Green/black stripedRayé vert/noir

GrayGris

LeftGauche

RightDroit

LeftGauche

RightDroit


*1 RCA pin cord (not supplied)*2 AUDIO OUT can be switched to SUB

or REAR. For details, see the supplied

operating instructions.

*1 Cordon à broche RCA (non fourni)*2 AUDIO OUT peut être commuté sur

SUB ou REAR. Pour obtenir plus de détails, reportez-

vous au mode d’emploi fourni.

Purple/black stripedRayé mauve/noir

Remarques sur les câbles de commande et d’alimentation• Le câble de commande d’antenne électrique (bleu) fournit une

alimentation de + 12 V CC lorsque vous mettez la radio sous tension.

• Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplifi cateur d’antenne existant. Pour plus de détails, consultez votre détaillant.

• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil.

Raccordement pour la conservation de la mémoireLorsque le câble d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt.

Remarques sur le raccordement des haut-parleurs• Avant de raccorder les haut-parleurs, mettez l’appareil hors

tension.• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms

avec une capacité électrique adéquate pour éviter de les endommager.

• Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes des haut-parleurs droit à celles du haut-parleur gauche.

• Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur.

• N’essayez pas de raccorder les haut-parleurs en parallèle.• Raccordez uniquement des haut-parleurs passifs. Le

raccordement de haut-parleurs actifs (avec amplifi cateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil.

• Pour éviter tout dysfonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un câble négatif commun (–) pour les haut-parleurs droit et gauche.

• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil.

Remarque sur le raccordementSi les haut-parleurs et l’amplifi cateur ne sont pas raccordés correctement, le message « FAILURE » s’affi che. Dans ce cas, assurez-vous que les haut-parleurs et l’amplifi cateur sont bien raccordés.

Notes on the control and power supply leads• The power antenna control lead (blue) supplies +12 V DC

when you turn on the tuner.• When your car has built-in FM/AM antenna in the rear/side

glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer.

• A power antenna without a relay box cannot be used with this unit.

Memory hold connectionWhen the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the left speaker.

• Do not connect the ground lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage the unit.

• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connectionIf speaker and amplifi er are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.

8

CDX-S2210/S2210S/S2210X/S2250EE/SW330

Connections (CDX-S2210S/S2210X)

9

CDX-S2210/S2210S/S2210X/S2250EE/SW330

Connections (CDX-S2250EE)

10

CDX-S2210/S2210S/S2210X/S2250EE/SW330

Connections (CDX-SW330)

Diagrama de conexión (3)1 A una superfi cie metálica del automóvil

Conecte primero el cable de conexión a masa negro, y después los cables con rayas naranjas y blancas, amarillo, y rojo de entrada de alimentación.

2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplifi cador de señal de la antenaNotas• Si no se dispone de antena motorizada ni de amplifi cador

de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable.

• Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.

3 A AMP REMOTE IN de un amplifi cador de potencia opcionalEsta conexión es sólo para amplifi cadores. La conexión de cualquier otro sistema puede dañar la unidad.

4 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de la llave de encendidoNotas• Si no hay posición de accesorio, conéctelo al terminal de

alimentación (batería) de +12 V que recibe energía sin interrupción.

Asegúrese de conectar primero el cable de conexión a masa negro a una superfi cie metálica del automóvil.

• Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.

5 Al terminal de alimentación de +12 V que recibe energía sin interrupciónAsegúrese de conectar primero el cable de conexión a masa negro a una superfi cie metálica del automóvil.

Notas sobre los cables de control y de fuente de alimentación• El cable de control de la antena motorizada (azul) suministrará

cc de + 12 V cuando conecte la alimentación del sintonizador.• Si el automóvil dispone de una antena de FM/AM incorporada

en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de entrada de alimentación auxiliar (rojo) al terminal de alimentación del amplifi cador de antena existente. Para obtener más información, consulte a su distribuidor.

• Con esta unidad no es posible utilizar una antena motorizada sin caja de relé.

Conexión para protección de la memoriaSi conecta el cable de entrada de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague la llave de encendido.

Notas sobre la conexión de los altavoces• Antes de conectar los altavoces, desconecte la alimentación

de la unidad.• Utilice altavoces con una impedancia de 4 a 8 Ω con la

capacidad de potencia adecuada para evitar que se dañen.• No conecte los terminales de altavoz al chasis del automóvil,

ni conecte los terminales del altavoz derecho con los del izquierdo.

• No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz.

• No intente conectar los altavoces en paralelo.• Conecte solamente altavoces pasivos. Si conecta altavoces

activos (con amplifi cadores incorporados) a los terminales de altavoz, puede dañar la unidad.

• Para evitar fallos de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo.

• No conecte los cables de altavoz de la unidad entre sí.

Nota sobre la conexiónSi el altavoz y el amplifi cador no están conectados correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos.

*1 RCA pin cord (not supplied)*2 AUDIO OUT can be switched to SUB or

REAR.For details, see the supplied operating instructions.

*1 Cordon à broche RCA (non fourni)*2 AUDIO OUT peut être commuté sur SUB

ou REAR. Pour obtenir plus de détails, reportez-vous

au mode d’emploi fourni.

*1 Cable con terminales RCA (no suministrado)

*2 AUDIO OUT (Salida de audio) puede cambiarse a SUB (Secundaria) o REAR (Posterior).Para obtener información, consulte el manual de instrucciones suministrado.BUS

AUDIOIN

L

R

L

R

AUDIO OUT REAR*2

2

4

5

1

3

2

AMP REM

Max. supply current 0.3 ACourant max. fourni 0,3 ACorriente máx. de alimentación de 0,3 A

Fuse (10 A)Fusible (10 A)Fusible (10 A)

Blue/white stripedRayé bleu/blancCon rayas azules y blancas

from car antennaà partir de l’antenne de la voituredesde la antena del automóvil

*1

RedRougeRojo

YellowJauneAmarillo

WhiteBlancBlanco

GreenVertVerde

PurpleMauveMorado

White/black stripedRayé blanc/noirCon rayas blancas y negras

Gray/black stripedRayé gris/noirCon rayas grises y negras

Green/black stripedRayé vert/noirCon rayas verdes y negras

GrayGrisGris

LeftGaucheIzquierdo

RightDroitDerecho

LeftGaucheIzquierdo

RightDroitDerecho

ANT REM

BlackNoirNegro

BlueBleuAzul


Corriente máx. de alimentación de 0,1 A

Purple/black stripedRayé mauve/noirCon rayas moradas y negras

Schéma de raccordement (3)1 À un point métallique de la voiture

Branchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’entrée d’alimentation jaune et rouge.

2 Vers le câble de commande d’antenne électrique ou le câble d’alimentation de l’amplifi cateur d’antenneRemarques• Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas

d’antenne électrique ni d’amplifi cateur d’antenne, ou avec une antenne télescopique manuelle.


3 Au niveau de AMP REMOTE IN de l’amplifi cateur de puissance en optionCe raccordement s’applique uniquement aux amplifi cateurs. Le branchement de tout autre système risque d’endommager l’appareil.

4 À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoiresRemarques• S’il n’y a pas de position accessoires, raccordez la borne

d’alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.


5 À la borne +12 V qui est alimentée en permanenceRaccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.

Remarques sur les câbles de commande et d’alimentation• Le câble de commande d’antenne électrique (bleu) fournit une

alimentation de + 12 V CC lorsque vous mettez la radio sous tension.

• Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplifi cateur d’antenne existant. Pour plus de détails, consultez votre détaillant.

• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil.

Raccordement pour la conservation de la mémoireLorsque le câble d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt.

Remarques sur le raccordement des haut-parleurs• Avant de raccorder les haut-parleurs, mettez l’appareil hors

tension.• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms

avec une capacité électrique adéquate pour éviter de les endommager.

• Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes des haut-parleurs droit à celles du haut-parleur gauche.

• Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur.

• N’essayez pas de raccorder les haut-parleurs en parallèle.• Raccordez uniquement des haut-parleurs passifs. Le

raccordement de haut-parleurs actifs (avec amplifi cateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil.

• Pour éviter tout dysfonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un câble négatif commun (–) pour les haut-parleurs droit et gauche.

• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil.

Remarque sur le raccordementSi les haut-parleurs et l’amplifi cateur ne sont pas raccordés correctement, le message « FAILURE » s’affi che. Dans ce cas, assurez-vous que les haut-parleurs et l’amplifi cateur sont bien raccordés.

AUDIOOUT

Connection diagram (3)1 To a metal surface of the car

First connect the black ground lead, then connect the yellow and red power input leads.

2 To the power antenna control lead or power supply lead of antenna booster amplifi erNotes• It is not necessary to connect this lead if there is no power

antenna or antenna booster, or with a manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

3 To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.

4 To the +12 V power terminal which is energized in the accessory position of the ignition key switchNotes• If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal

surface of the car fi rst.• When your car has a built-in FM/AM antenna in the rear/

side glass, see “Notes on the control and power supply leads.”

5 To the +12 V power terminal which is energized at all timesBe sure to connect the black ground lead to a metal surface of the car fi rst.

Notes on the control and power supply leads• The power antenna control lead (blue) supplies +12 V DC

when you turn on the tuner.• When your car has built-in FM/AM antenna in the rear/side

glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer.

• A power antenna without a relay box cannot be used with this unit.

Memory hold connectionWhen the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the left speaker.

• Do not connect the ground lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage the unit.

• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connectionIf speaker and amplifi er are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.

11

CDX-S2210/S2210S/S2210X/S2250EE/SW330

SECTION 2DISASSEMBLY

Note : This set can be disassemble according to the following sequence.

Note : Follow the disassembly procedure in the numerical order given.

2-1. SUB PANEL (LCD) ASSY

2-1. SUB PANEL (LCD) ASSY ()

2-2. CD MECHANISM BLOCK(Page 12)

SET

2-3. MAIN BOARD(Page 12)

2-4. CHASSIS (T) SUB ASSY(Page 13)

2-5. ROLLER ARM ASSY(Page 13)

2-6. CHASSIS (OP) ASSY(Page 14)

2-8. SL MOTOR ASSY (M902)(Page 15)

2-10. SERVO BOARD(Page 16)

2-7. OPTICAL PICK-UP(Page 14)

2-9. LE MOTOR ASSY (M903)(Page 15)

2 two claws

3 two claws

4 sub panel (LCD) assy

1 two screws (+PTT 2.6 x 6)

12

CDX-S2210/S2210S/S2210X/S2250EE/SW330

2-2. CD MECHANISM BLOCK

2-3. MAIN BOARD

7 bracket (CD)

5 CD mechanism block

4 CNP301

3

1 screw (+PTT 2.6 x 6)

2 screw (+PTT 2.6 x 6)


1 three screws (+BTT)

3 MAIN board

4 insulating sheet


13

CDX-S2210/S2210S/S2210X/S2250EE/SW330

2-4. CHASSIS (T) SUB ASSY

2-5. ROLLER ARM ASSY

3 washer (1.1-2.5)

4 gear (RA1)

5 roller arm assy

1 spring (RAL)

2 spring (RAR)

5 SENSOR board

6 chassis (T) sub assy

4 claw

3 claw

1 two screws (+P 1.7 x 2.2)

2 two screws (+P 1.7 x 2.2)

14

CDX-S2210/S2210S/S2210X/S2250EE/SW330

2-6. CHASSIS (OP) ASSY

2-7. OPTICAL PICK-UP

4 washer

0 coil spring (damper)

9 two coil springs (damper)

qa chassis (OP) assy

5 gear (LE1)

1 CN2 (16P)

lever (D)

slider (R)

6

7

8

2 Remove the six solderings.

3 tension coil spring (KF60)

1 tension coil spring (CHKG)

2 chucking arm sub assy

3 screw (+B 1.4 x 5)

4 rack (SL)

5 claw

6 main shaft

7 optical pick-up

15

CDX-S2210/S2210S/S2210X/S2250EE/SW330

2-9. LE MOTOR ASSY (M903)

2-8. SL MOTOR ASSY (M902)

1 screw (+P 1.4 x 1.8)

2 SL motor assy (M902)

2 washer

4

qd

3 gear (LE1)

7 leaf spring (LE)

5

lever (D)

bracket (LEM-N)

slider (R)

6 screw (+P 1.7 x 2.2)

8 screw (+M 1.7 x 2.5)

qa screw (+M 1.7 x 2.5)qf two toothed lock screws

(+M 1.4 )

qs screw (+M 1.7 x 2.5)

9 bearing (LEB-N)

0 gear (LE) assy

qg LE motor assy (M903)

1 Remove the soldering.

16

CDX-S2210/S2210S/S2210X/S2250EE/SW330

2-10. SERVO BOARD

3 CN2 (16P)

5 claw

6 SERVO board

4 toothed lock screw (M 1.7)

1 Remove the eight solderings.

2 Remove the three solderings.

17 17

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-1. BLOCK DIAGRAM – CD SECTION –

SECTION 3DIAGRAMS

87RFO

RF AMP,DIGITAL SERVO,DIGITAL SIGNAL PROCESSOR

IC2

79RFEQO

3RFRP

6TEI

77 RFI78 RFRPI

1 RFZI

7 TEZI

9 F0O

PD1

PD2

E

F

I-V A

MP

PD LD

DETECTOR

85 AGCI86 RFDCI

94

96

95

97

99

98

TNI

FPI1

FNI1

FPI2

FNI2

TPI

91 LDO 92MDI

(FOCUS)

(TRACKING)

2-AXIS DEVICE

OPTICALPICK-UP BLOCK

(KSS1000E)

• Signal Path: CD PLAY

LASER DIODE

M

M

M

18

17

VO3–

VO3+

14

13

VO1+

VO1–

12

11 VO2–

VO2+

10

9

VOL+

VOL–FWD

REV

1

28

OPIN4– 26

OPOUT4 25

10 TROOPIN3– 23

46 IO0(/HSO)OPOUT3 22

12 FMOOPOUT1 4

13 DMOOPIN2 7

47 IO1(/UHSO)MUTE 21

16

15

VO4–

VO4+

M903(LOADING)

M901(SPINDLE)

M902(SLED)

FOCUS/TRACKING COIL DRIVE,SLED/SPINDLE/LOADING

MOTOR DRIVEIC1

56MUTE53REQ43STBY18ZDET42/RST41/CCE40BUCK39BUS3

CD-L MAIN SECTIONA30LO

27RO R-CH

27 DEC SSTBY15 CD ZDET14 CD XRST13 CD XCCE

53 MEC_SELFSW

45 MEC_INSW

42 MEC_LIMIT

12 CD BUCK11 CD BUS3

38BUS2 10 CD BUS237BUS1 8 CD BUS136BUS0 7 CD BUS014SBSY 52 CD SBSY

81 X1

80 X0

MEC LOAD43

MEC EJECT44

CDSYSTEM CONTROL

IC3

+1.5V REGIC6

SYSTEM CONTROLIC501 (1/3)

37 DEC XMUTE30 DEC INT

SW2(SELF)

46 MEC_DSWSW1(DOWN)

SW3(DISC IN)

SW4(LIMIT)

56UNISI25RXD57UNISO

58UNICKI50BUS ON51BU IN

75RSTX

61EJECT OK

67MECON CHK

11.5V ON

63MECON64CDON66ZMUTE

60A ATT

26TXD

PD1

E

F

LD

MON OUT

FCS+

FCS–

TRK+

TRK–

PD2

AUTOMATICPOWER

CONTROLQ1

+1.5V ON/OFFSWITCH

Q2,3

• R-ch is omitted due to same as L-ch.

24

23X2

16.934MHzX1

12MHz

XI

XO

DISPLAY SECTIONC

MAIN SECTIONB

EJECT OK SW

UNI SI

UNI SO

ATT

UNI CLKBUS ONB/U CHECK

SYS RST

89

CD ON

VOUT

98CDM ON99

Z MUTE

MECHA+6V

93

68CDON CHK

15 VDD3CE

BU+3.3V

+1.5V

+1.5V

BU+3.3V

(Page 18)

(Page 18)

(Page 19)

1818

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-2. BLOCK DIAGRAM – MAIN SECTION –

1 ANT 7 TU LCH

ELECTRONIC VOLUMEIC401

J1(ANTENNA)

TU1(TUNER UNIT)

POWER AMP, POWER SUPPLY

IC750


CN601

6 TU RCH

R-CH (FRONT)R-CH (REAR)

BATT

9 CD LCH8 CD RCH

R-CH

43

10VCC11TU VDD15E2P VDD

13TU-SCL14TU-SDA

6S-METER7TU MUTE

16E2P SCL17E2P SDA

39 VSM

AUDIO+8.3VTU+5VBU+3.3V

12 TU ATT

25 EEP CKO24 EEP SIO

L-CHR-CH

CD-L

R-CH 1718

OUT SUB-LOUT SUB-R

R-CH

L

R

53

OUT FL+OUT FL-

97

OUT RL+OUT RL-

2927

AMP-REM

R-CH

ANT-REM

BATT

3037

AUDIO8.3VB.UP+B

3133

SERVO3.3VMECHA6V

34PANEL+B

TU+5V

BATT

2524

OUT FROUT RR

29MUTE

2 SDA

AUDIO+8.3VBU+3.3VSERVO+3.3VMECHA+6VPANEL+B

4 SCL

SDASCL

16 BEEP22 STB25 DIAG

AUDIO+8.3V

35 VP

15

7

10

12

11

16

19

2

4

3

56

3031

SCLSDA

SCLSDA

SCLSDA

SCLSDA

33I2C CKO34I2C SIO

9VOL ATT

86ATT5BEEP26AMP STB8DIAG

54BU IN

73

UNI SI58UNI SO59UNI SCK60BUS ON87

UNI SIUNI SOUNI CLKBUS ONB/U CHECK

ATT

TEST IN

12 IN FL FL+FL-

RL+RL-

FR+FR-RR+RR-

AMP-REMANT-REM

ACC

TEST

23OUT FL

11 IN RL22OUT RL

MUTEQ441

MUTEQ481

AUDIO OUTJ330

MUTE DRIVEQ478,479

BATT

72

74

ACC IN

TEL ATT

BATTERY CHECKQ580-582

ACC CHECKQ631

+5V REGQ1

MUTEQ461

13TEL-MUTE

D479

D571

D580,581

FU601

CD SECTION A

CD SECTION B

TEL MUTEQ651

• Signal Path• R-CH is omitted due to same as L-CH.

: CD PLAY

: FM

: MW/LW

S2250EE

(Page 17)

(Page 17)

19 19

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-3. BLOCK DIAGRAM – DISPLAY SECTION – • Circuit Boards Location

MAIN boardKEY board

SENSOR board

SERVO board

tuner unit(TU1)

KEY ACK ONQ664

X50232.678kHz

79

80

82

83

41

282927

40

52

76

77


LCD DRIVERIC901

KEYIN0

CLKCE

LCD SOLCD CKO

LCD CE

DIMMER

KEYIN1

KEY ACK

XKEY ON

7 NOSE DET

3 AREA SEL0

88 SYS RST

RESET2 1

XOUT

XIN

OSC IN

OSC OUT

X50118.432MHz

S702RESET

6364

62

1

COM4

COM1

LCD901

LIQUIDCRYSTALDISPLAYPANEL

D503

S502(FREQUENCY SELECT)

9k T 10k

BU+3.3.V

S2210S,S2210X

D510

4|

50•

55

51|

54|

S1

S48|

CLDI

CE

64SIRCS IR

LED951,952LSW901-911,

913-921

Q921LED

CONTROL

LED931,932

PANEL+B

IR RECEIVERIC971

2 OUTBU+3.3V

SYS RST

( )

KEY MATRIX

RESETIC602

LSW901-911,913-921

VDD VOUT

LCD BACK LIGHT

CDSECTION C

(Page 17)

2020

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

• Waveforms

— SERVO Board —

(CD PLAY) — MAIN Board —

• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printedin each block.)

For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• f : internal component.• C : panel designation.

For printed wiring boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• a : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

• A : B+ Line.• B : B– Line.• H : adjustment for repair .• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.• CD mechanism section (1/2), (2/2) no mark : CD PLAY• Main (1/4), (2/4), (3/4), (4/4) and Display sections no mark : FM

( ) : AM< > : CD PLAY

∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 M Ω).

Voltage variations may be noted due to normal produc-tion tolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

• Circled numbers refer to waveforms.• Signal path.

J : CD PLAYF : FMf : AM

Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.

Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.

Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepiéce portant le numérospécifié.

Q

C

These are omitted

EB

EThese are omitted

CB

CThese are omitted

BE

1 IC501 i; (XIN)

1.4Vp-p

32.678kHz

1.2Vp-p

18.432MHz

2 IC501 id (OSCOUT)

1 IC2 4 (FEI)

Approx.1Vp-p

0 V

0.6 Vp-p

16.9344 MHz

Approx. 100 mVp-p

50 mV/DIV, 5 msec/DIV 0.5 V/DIV, 0.5 µsec/DIV

2 IC2 6 (TEI)

200 mV/DIV, 5 msec/DIV

6 IC2 oh (FPI2),

0.5 V/DIV, 0.5 µsec/DIV

Approx. 400 mVp-p

3 IC2 wd (XI)


7 IC3 ia (X1)


1.1 Vp-p

12 MHz

4 IC2 uj (RFI)


5 IC2 of (FNI2),og (FNI1)

1.5 Vp-p

oj (FPI1)

1.5 Vp-p0 V

Ver. 1.3

NOTE FOR REPLACEMENT OF THE IC501IC501 on the main board has two types of IC models: MB90487 and MB90F488B.The service part is the model MB90487 only.Check the model number printed on the IC when replacing IC501.If MB90F488 is printed on the IC, mount the capacitor C551 additionally.

JAPANF

MB90487AMB90F488B

company emblem

IC501 C351

MB90487A 0.001µF

MB90F488B NO MOUNT

21 21

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-4. PRINTED WIRING BOARDS – SERVO BOARD – • See page 19 for Circuit Boards Location. : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

(KSS1000E)

SW3

SW2

MAIN BOARD CNP301

TP24

TP40

TP17

TP14

TP18

TP37

TP38

TP39

TP30

FMA4

FMA6

FMA3

TP48

TP49TP51TP53

FMA5C37

C9

C38

C39C40C4

1

C43

C48

C67

C72

FB3

R132

R6

R7

R48

R50

R16

R17

R40

R41

R8

R25 R26

R84

R86

R13

1

R122

Q1

IC6

SW1(DOWN)

C106

R12

0

C65

C64

C19R

123

C20

C61

Q3

FB4

C29

C22

R65

C32

C51

C35

C45

C62

R11

R9

C57

R10

IC3

R12

FB2

C6

R11

2

R58

R42

R113

R43

R47

R54R

56R

57R

66

R68

R69

R70

R73 R100

R10

1R13

R21

R71

Q2

C7

C101

C102

C80

C103

IC1

TP4

TP3

TP5

TP33

TP34

TP35TP

36

TP41

TP42

TP47

TP46

TP25

TP26TP27

TP21

TP22

TP68

TP93

TP15

TP64

FMB3

FMB4

TP11

TP86

TP87

TP10

TP1

TP6

TP7

TP8

TP9

TP12

TP13

TP16

TP20

TP32TP

31

TP66

TP67

TP74

TP75TP76

TP77

TP78

TP79TP80TP81

TP82

TP83

TP84

TP85

TP90

TP89

TP88

TP91

TP92

TP95

TP97TP98

TP99

TP2

TP63

TP44

TP43

TP65

TP62

FMB5

TP101

TP23

TP29

CN1

R4

R24

R5

CN2

R61

C5

R49

R51

R45

R46

R2

R3

X1

X1

IC2

R121

C10

C4

R11

9

C18

C47

C34

R11

8

C17

C23

C42

C16

C60

R125

C36

R62

R117

C21

R116

X2

C24

C31

C28

R12

6

C52

R12

7

C49

R128

C53

R63

R64

C13

R28

R1

C27

R53R55

R67

R60

R74

R77

R78

R80

R81

R82

R83

R90

R91

C33

R19

R22R23

R44

R52

R72R

59

C59

C105

C58

1-864-900-

11

11 1-864-900-

11

11

A(Page 24)

IC1 G-2IC2 B-11IC3 E-2IC6 D-1

Q1 B-4Q2 C-1Q3 C-1

• SemiconductorLocationRef. No. Location

2222

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-5. SCHEMATIC DIAGRAM – SERVO BOARD (1/2) – • See page 32 for IC Block Diagram. • See page 20 for Waveforms.

IC B/D

IC B/D

CN1

R6 R7

Q2 R86

R84

TP41

TP46

TP30

TP47

R22

R71R72

R26

R40

R44

C61

R25

R41

TP42

TP21 TP22

TP29

R23

R21

R24

TP93

TP101

R49

C59R131

R113

C5

C27

C23

C20C19

C17

C18

C21

C29

C35C32

C33

C72C80

Q3

C102

C53

C51

C49 C57

C48

C45

C42

FB2

FB3

C67

R52

C52C47

C16

C13

C31

R19

R46R45

FB4

R123

C36

R132

R5

R4

R51

R112

Q1

C9

TP37

TP38

TP39

TP40

IC6

R13

IC2

R1

C10

X2

C28

C24

C22

C4

C7

C101

TP12

TP13

TP20

TP18TP17

TP16

TP15

TP14

TP27

TP26

TP25

R125R126R127R128 R64

R62

R63

R61

R60

R59

C62

C58C60

C34

C41

C40

C39

C38

TP34

TP36

TP35

TP33

(Page 23)

23 23

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-6. SCHEMATIC DIAGRAM – SERVO BOARD (2/2) – • See page 31 for IC Block Diagram. • See page 20 for Waveforms. • See page 35 for IC Pin Descriptions.

IC B/D

R81

R82

R83

R55 TP

62TP53

TP51

TP49

TP48

TP44

TP65

TP64

TP63

R47

R73

R48

R50

R53

R11

R10

R8

R9

TP32

TP31

TP10

TP11

TP43

TP67

TP66

TP23

TP24

R11

6

R11

8

R11

9

R121

TP97

TP98

TP99

C106

C37

R78

R77

R91

R90

R80

R117R122

R42 R43

R74

R17

R16

C6

R100

R101

IC1

CN2

R12

TP7

TP6

TP9

TP8

SW4

SW1

SW3

SW2

M903

M901

M902

R2

R3

R120

IC3

C105

R28

X1

C43

C64

C65

C103

TP74

TP75

TP76

TP77

TP78

TP79

TP80

TP81

TP82

TP83

TP84

TP85

TP86

TP87

TP88

TP89

TP90

TP91

TP92

TP1

TP2

TP3

TP4

TP5

R58

R54

R56

R66

R68

R69

R67

R65

R57

R70

(Page 22)

2424

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-7. PRINTED WIRING BOARD – MAIN BOARD – • See page 19 for Circuit Boards Location. : Uses unleaded solder.1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

EXCEPT S2250EE

S2250EE

S502S2210S,S2210X

S2210,SW330

9K

10K

FREQUENCYSELECT S2250EE

S2210,S2250EE,SW330

S2250EE

EXCEPTS2250EE

Q478

Q479

Q651

Q582

C502

R508

R509

R513

R514

C504

C508

C507R510

R511

R512

Q664

R517

R528

C413

R405

R406

R407

R409

R408

D1

C6

R2

R3

R501

C501

R503

R58

2

D580

Q581

R651

R653

R654

D651

R609

D609

R632R634

R633

Q631

R636

Q580

R521

R522

R585

R584

D581

R58

3

R532

R531

JC75

3

C343

R674

R671

R672

R534

R756

C755

R752

C7

R479

D479

C770

C769

R1

R536

R535

C404

C405

C756

Q1

R537

R453

R463

FMB3

FMB4

C11

C509R504

R505

R673

L1

R540

R541

IC40

1

C510

C512

C513

C514C516

R544

JC681

R550

R546

R471

R472

Q471

R481

R482

Q481

R461

R451

C763

D719

R4

R5

R518

R557

R563

R564

R551

R545

C617

C618

C764C765C751

C750

C602

C12

C13

JC401

R410

R411

R301

R302

C306

C308

C310C309

FB603

FB605

FB604

R652

C771

R573

R538

R507

R549

FB1 FB309

FB305

FB30

3

FB307

FB308

JC527

C484 C474

JC75

4

JC75

5

JC446

R533R703

D512

IC602

D510

D511

R431 R433

Q43

1

R432

R441

R443

Q44

1

R442

FB302

FB304

C312

R561

R558

R568

R565

R567

R529

R570

JC501

JC503

R12

R13

D702

D701

C519

JC12

R502

JC445

Q46

1

Q451

R462

R452

JC1

FB310

R40

1

JC533

R601D502

R519

D503JC504

L301

C442

C432

C452

C462

C774C775C776

JC58

1

JC511

R575

R577

JC50

6

R566

L501

R542

R543R556

R547

R578

JC75

6

D763

D764

R539

FB501

FB606

1-864-520-

R675R676

R677

R679

R681

D617

R705

R706

R707

IC501

C531

JW10

JW11JW

12

JW13

JW29

JW31

JW32

JW90

JW101

R63

1

JW10

4

JW10

5

C431C461

C451

C401

CN701

S702

S702RESET

C301

C302

C601

J1

TU1TUNERUNIT

C761

X502

C758

C752

C441

D75

7

D75

9

D76

0

D60

1

C631

JW9

D75

8

C759

C754

C407

C406

JW1

JW2

JW95

JW97

JW63

JW51

JW52

JW49

C305

JW91

JW115

JW129

JW130

JW94

JW57

C471

C481

JW13

1

JW13

2

JW110

D75

5

D75

6

JW27

C760

C753

C479

C412

C4C5

C511

C503

JW59

D761

S2250EE

S2250EE

EXCEPT S2250EE

D762

JW78

JW3

JW25

JW109

JW144

JW14

5

JW14

6

L601

JW39

CNP301

JW14

2

JW14

3

JW93

JW89

JW81

JW16

JW15

JW14

JW17

JW56

JW50

CN601

FU601

JW12

0

JW22

JW11

8

JW24

C622

C623

JW18

JW128

JW65

JW82

JW75

JW119

JW14

9

JW45

JW12

7

JW67

JW58

JW83X5

01

JW6

JW8

JW13

7

JW7

JW30

JW99

JW28

JW117

JW62

JW100

JW92

JW14

1

JW66

JW111

JW106

JW113

JW20

JW14

0

JW73

JW74

JW13

3

JW121

JW80

JW122

JW60

JW15

0

JW44

JW48

JW88

JW70

JW53

JW68

J330AUDIO OUT

JW40

JW69

JW10

3

JW10

8

JW42 JW

23

JW5

IC750

JW123

JW54

JW139

JW71

JW76

JW13

8

JW26

JW98

D75

4

D75

3

D75

2

D75

1(Page 21)

(Page 29)

Ref. No. Location

D1 F-3D479 E-6D502 I-7D503 I-5D510 G-8D511 F-6D512 H-8D580 F-10D581 F-10D601 C-10D609 C-8D617 C-9D651 C-9D701 I-3D702 I-3D719 I-4D751 C-7D752 C-7D753 C-7D754 C-7D755 C-6D756 C-6D757 C-6D758 C-6D759 D-8D760 D-8

• Semiconductor Location

Ref. No. Location

D761 C-9D762 D-9D763 D-8D764 D-8

IC401 E-3IC501 H-6IC602 I-9IC750 B-6

Q1 F-3Q431 B-4Q441 B-4Q451 C-4Q461 D-4Q471 B-3Q478 E-6Q479 E-5Q481 C-3Q580 F-10Q581 I-10Q582 I-10Q631 H-10Q651 D-8Q664 I-7

Ver. 1.3

Refer to page 20 forNOTE FOR REPLACEMENT OF THE IC501

25 25

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-8. SCHEMATIC DIAGRAM – MAIN BOARD (1/4) – • See page 32 for IC Block Diagram. • See page 20 for Waveforms.

IC B/D

C401

L1

C406

JC401

FB1

JC446

JC12JC1

R479

R405

R406

R407

R408

R409

C431

C451

C441

C461

R431

R451

R441

R461

R432

R452

R442

R462

R433

R453

R443

R463

D1

R1

R410

R411

C471

C481

R471

R481

R472

R482

R4

C13

C6

C11

C405

C404

C413

C484

C462

C442

C432

C452

C474

IC401

Q481

Q471

Q461

Q451

Q441

Q431

Q479

Q478

D479JC445

C407

R13

R12R3

R2

TU1

J1

Q1

C479

R5

C4

C412

R401

J330

C7C5

C12

(Page 26)

(Page 27)

2626

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-9. SCHEMATIC DIAGRAM – MAIN BOARD (2/4) – • See page 34 for IC Block Diagram.

IC B/D

L601

R609

JC756

D76

3

D76

4

D617

D751

D752

D753

D754

D755

D756

D757

D758

C753D

761

D76

2

R752

C758

C760

C752

C754

C776

C751

JC754

JC753

C770

C769

C763

C775 C765 C764 C774

C617

C618

C602 C601

IC750

C750

JC755

FU601D

759

D76

0

D601

CN601

C755

R651

D651

(Page 25)

(Page 28)

27 27

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-10. SCHEMATIC DIAGRAM – MAIN BOARD (3/4) – • See page 20 for Waveforms. • See page 37 for IC Pin Descriptions.

R636

R51

1

R674

R536

R57

0

FB302

FB30

8

X502

R55

7

R53

2

R55

1

R57

3

R528

R505

R504

R563

R54

4

R522R521

JW14

5JW

146

JW127 R565

FB310

JW28

D50

2

JC533

JC511

R57

5

JW120

JW48

JW49

R75

6

R503R502

R533

C503

R531

R517

R501

R518

R519

FB303

FB305

C306

FB304

C507

C510

L501

C756

C504

C502

C509

JC501

C514

C501

C513

C511

R564

R543

R567

R561

JC503

R671

C512

JC504

R534 R513R514

R51

2R

510

R577

C531

CNP301

C312

FB309

R578

D510

JC527

X501

C508

FB501

R55

0

R566

R673

D503

Q664

D512

R535D511

R54

7

R54

2

R679

C305

C343C301

IC501

R556

R558 R568

C516

R508

R509

L301

C308

R302

R301

FB307

C310

C309

C302

R53

7

R53

8

R50

7R

549

R54

6R

545

S502

R675R676

R681

R677

R539

R67

2

R52

9

(Page 25)

(Page 28)

MB90487APF-G-118-BND1MB90F488BPF-G-9004E1

Ver. 1.3


2828

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-11. SCHEMATIC DIAGRAM – MAIN BOARD (4/4) –

R633

R632R634 R654

R652

R583

R582

C623

JC681

JW98

JW53

R706

R707

C622

R585

CN701

R584

C631

FB605

D701 D702

R601

C519

FB604

R631

JC581

FB603

Q581

Q582

Q580

D581

D580

D609

R653

JC506

R540

R541

R703

R705

D719

S702

IC602

Q651

C759

C771

C761FB606

Q631

(Page 26)

(Page 27)

(Page 30)

29 29

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-12. PRINTED WIRING BOARD – KEY BOARD – • See page 19 for Circuit Boards Location. : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

B

MAIN BOARDCN701

R907

R909

LED941

LED942

LED951

R910IC971

LSW910

LSW911

1-864-522- 11

1-864-522- 11

LSW906

LSW904

LSW903 LSW907

LSW921

LSW921

LSW905

LSW906

VOL

LSW904

SOURCE MODE

LSW920

(LCD

BAC

K LI

GH

T)

(LCD

BAC

K LI

GH

T)

LSW919 LSW918 LSW917 LSW916 LSW915 LSW914 LSW913 LSW902OFFBTM654/SHUF3/REP2/GROUP +1/GROUP –SENSDSPL/DIM

IC971

LSW911,LED942

SEEK

EQ3ATT

LSW901

LSW910,LED941

LSW920 LSW919LSW918 LSW917 LSW916 LSW915 LSW914

LSW913LSW902

LSW909LSW908

R90

8

R95

7

R951R952

R943R944 R939

R94

0

R93

5

R936

JP93

5

R926

R929

R930

LSW905

LED952 LED952(DISC-L)

LED951(DISC-R)

LSW901

LED

931

LED

932

R968

R925

52 40

LCD901LIQUID CRYSTAL DISPLAY PANEL

3020

10 1

R956

R955

R973

R921

R933

R922

R91

1

R91

2R91

3

R914

R91

5R916R

917

R918

R91

9

R901

R902

R90

3R

904

R90

6

IC901

C971

R97

2

R97

4

R97

6

R97

7

R978

R979

D901R981

R982

D98

1

C981

C982R983

R98

4R

985

R98

6

R98

7

C983

C984

C985

D902

D98

2

Q92

1

R947 R948

R90

5

R967 R961

R962R963

FMB4

R995

FMB3

C986

JP961

(Page 24)

D901 G-11D902 G-11D981 G-6D982 G-10

IC901 G-8IC971 D-14

Ref. No. Location


Ref. No. Location

LED931 C-12LED932 C-4LED941 B-14LED942 C-14LED951 A-12LED952 A-2

Q921 G-4

3030

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

3-13. SCHEMATIC DIAGRAM – KEY BOARD –

D901

D902

R901 R902 R903 R904 R905 R906

R919R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917

D981

R972

R981

R982

R918

JP935

R962

R963

JP961

CN901

R973

R976

R974C971

C982

C986C985

C981

R983

D982 R987

LED931

LED932

LSW901(2/2)

LSW909(2/2)

LSW908(2/2)

LSW910(2/2)

LSW911(2/2)

LSW902(2/2)

LSW915(2/2)

LSW913(2/2)

LSW916(2/2)

LSW914(2/2)

LSW904(2/2)

LSW917(2/2)

LSW921(2/2)

LSW918(2/2)

LSW920(2/2)

LSW919(2/2)

LSW907(2/2)

LSW903(2/2)

LSW905(2/2)

LSW906(2/2)

Q921

R995

LCD901

IC901

R921

LED951

R925

LED942

LED941

R929

R936

R935

R939

R943

R940

R968

R944R948

R947

R951

IC971

R961

R967

LED952

R922

R933

R926

R930

R952

R984R985R986

R977

R979R978

C984C983

R955

R956

R957

LSW

908(

1/2)

LSW

909(

1/2)

LSW

910(

1/2)

LSW

911(

1/2)

LSW

913(

1/2)

LSW

914(

1/2)

LSW

915(

1/2)

LSW

916(

1/2)

LSW

917(

1/2)

LSW

918(

1/2)

LSW

919(

1/2)

LSW

920(

1/2)

LSW

921(

1/2)

LSW

901(

1/2)

LSW

902(

1/2)

LSW

903(

1/2)

LSW

904(

1/2)

LSW

905(

1/2)

LSW

906(

1/2)

LSW

907(

1/2)

(Page 28)

31

CDX-S2210/S2210S/S2210X/S2250EE/SW330

1

2

11

13

14

12

LEVELSHIFT

LEVELSHIFT

LEVELSHIFT

LEVELSHIFT

MUTE

FWD

FWD

LDCTL

NC

OPOUT1

NC

NC

OPOUT2

POWVCC VCCVOL–

VOL+

VOL2–

VOL2+

VO1–

VO1+

REV

OPIN4+

OPIN4–

OPOUT4

OPIN3+

OPIN3–

OPOUT3

MUTEVOL+GND

VOL3–

VOL3+

VOL4–

VOL4+

REV

OUTR OUTF

10

98

7

6

5

28

27

26

25

24

23

22

212019

18

17

16

15

4

3

IC1 BA5968FP-E2

• IC Block Diagrams

32

CDX-S2210/S2210S/S2210X/S2250EE/SW330

32 31 30 29 28 27 26 25 24 23 22

I2C BUSLOGIC

VCO

MIX

FADER(0~-58,-∞dB)

FADER(0~-58,-∞dB)

FADER(0~-58,-∞dB)

FADER(0~-58,-∞dB)

VOLUME(+23~-79dB,-∞dB

1dB STEP)


1dB STEP)

INPUT GAIN(0~15dB,1dB STEP)

INPUT SELECTOR(4 STEREO INCLUDE 1 ISOLATION INPUT)


ANTI-ALIASINGFILTER

ANTI-ALIASINGFILTER

MUTE

fc:40kHz fc:40kHz

MUTE

6 7 8 9 10 113 4 521

DGND

AGND FI

L

AN AP2

AP1 B1 B2 C1 C2 NC NC NC NC NC NC NC

12 14 1613 15

SDA

SCL

MUT

E

SEL

ADJ

VCC

OUTF

1

OUTR

1

OUTF

2

OUTR

2

NC NC NC OUTS

1

OUTS

2

21 20 19 18 17

VCC

VCC/2

TONEPASS

BASSfo:60,70,80,100,120,140,160,200HzQ:0.5,0.75,1,1.25

MIDDLEfo:500Hz,1kHzQ:1

TABLEfo:5,7.5,10,12.5kHz

TONEPASS

EFFECT (0dB~+20dB,2dB STEP)

EFFECT (0dB~+20dB,2dB STEP) 2ND ORDER

LPF

2ND ORDER LPFfc:OFF,80,120,160HzQ: 0.707

BASS,TREBLE, MIDDLE(-15dB~+15dB,1dB STEP)


GAIN+ATT(+10~-29,

-∞dB)

IC401 BD3808FS-FE2

1

VREF

VDD

GND

CE

CURRENTLIMIT

2

3

5 VOUT

NC4

IC6 R1114N151D-TR-FA

33

CDX-S2210/S2210S/S2210X/S2250EE/SW330

76

77 EFM SLICE

79

78

82

83

84

88

RFRP

VCOSLCO

RFI

RFRPI

REFQO

RESIN

VRO

VMDIR

TESTR

INVSEL

AGCI

RFDCI

RFO

PNSEL

EQSET

RVDD3

LDO

MDI

RVSS3

FNI2FNI1FPI2FPI1

TPI

TNI

FTE

RFZI

AVSS

3

RFRP FE

ISB

AD/R

FDC

TEI

TEZI

AVDD

3

FOO

TRO

VREF

FMO

DMO

SBSY

SBOK IP

F

SFSY

GPIN

VDD1

5

ZDET

VSS1

5XV

SS3 XI XO

XVDD

3

PVSS

3

VCOR

EF

VCOF

PVRE

FLP

FO

LPFN

TMAX

PDO

PVDD

3

AWRC

VSS1

5VD

D15

LRCK

IBC

KIAI

N

LRCK

OBC

KO

DOUT

PIO3

AOUT

PIO2

PIO1

PIO0

TEST

C

VDDP

VCOIVSSPTESTD

IO1IO0

FGIN

VDDT

STBY

/RST

/CCEBUCKBUS3BUS2BUS1BUS0VSS15

VDDMVDD3VSS3DVSS3

LO

DVR

DVDD3

RO

DVSS3

AUDIOOUT

DIGITALOUT

PLLTMAX

RFEQ

85 AGC

86 RFDC

87 RF

RAMDIGITAL EQAUTO ADJ. ROM

91APC

92

94

FE95

98TE

99

100

21 3 54 6 7 8 9 10 11 12 13 20 21 2214 15 16 17 1918

9697

80VRO

81

89

90

93

23

ANA.LPF

24 25

SYNC SIGNAL PROTECTIONEFM DEMODULATION

69 68 63 62 61 56 55 54 53

50

45

44

43

41403938373635

34333231

30

29

28

27

26

42

4948

4647

60 59 58 57 52 5166 65 6467707475 73

1-BITDAC

CLOCKGEN.PWM

SUBCODEDEMODULATION

CIRCUIT

16KRAM

ADDRESS CIRCUITCPUI/F

CORR

RECT

ION

CIR

CUIT

5-BITR-2R DAC

SERVOCONTROL

10-BITSAR ADC

72 71

CLV SERVO CAV SERVO

AWRC

IC2 TC94A60MFG-301

34

CDX-S2210/S2210S/S2210X/S2250EE/SW330

MUT

EM

UTE

ENABLELOGIC

STANDBY/MUTE

BATTERYDETECTION

CHIP DETECT/DIAGNOSTIC

PROTECTION/DIAGNOSTIC

SWITCH

REGU

LATO

R

SWITCH

REFERENCEVOLTAGE

LOADDUMPPROTECTION

TEMPERATUREPROTECTION

BACK-UPSWITCHREGULATOR

1

3

5

7

9

11

13

15

17

19

21

23

25

27

29

31

33

35

37

2

4

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

TAB

OUT-FL-

OUT-FL+

OUT-RL-

OUT-RL+

IN-RL

S-GND

IN-RR

OUT-RR+

OUT-RR-

OUT-FR+

OUT-FR-

DIAG

ANT-REM

AMP-REM

SERVO5V

MECH6V

VP

B.UP+B

SDA

SCL

VP2

PGND3

SVR

IN-FL

IN-FR

BEEP

PGND2

VP1

STB

PGND1

RST

CRES

AUDIO8.3V

GND

PANEL+B

CBU

FL

RL

RR

VP

FR

I2C BUS

IC750 TDA8588BJ/N2/R1

35

CDX-S2210/S2210S/S2210X/S2250EE/SW330

• IC Pin DescriptionsIC3 MB90487APFV-G-131-BNDE1 (CD SYSTEM CONTROL) (SERVO BOARD (2/2))

Pin No. Pin Name I/O Pin Description

1 NC O Servo 1.5 V power supply control signal output

2 to 6 NC — Not used. (Open)

7 CD BUS0 I/O Bus data signal input/output 0


9 VSS — Ground pin



12 CD BUCK O Bus clock signal output

13 CD XCCE O Chip enable signal output

14 CD XRST O Reset signal output

15 CD ZDET I Zero detection signal input


21 VCC — Power supply pin (+3.3 V)

22 DAC ZDETL I Zero data detection signal input (L-ch)

23 DAC ZDETR I Zero data detection signal input (R-ch)

24 NC — Not used. (Open)

25 RXD I UART RXD data signal input (MCBUS/Flash data input)

26 TXD O UART TXD data signal output (MCBUS/Flash data output)

27 DEC SSTBY O SRAM STANDBY mode control signal output

28, 29 NC — Not used. (Open)

30 DEC INT I Request signal input


33 AVCC — Power supply pin (+3.3 V) for A/D converter

34 AVRH — External reference voltage for A/D converter

35 AVSS — Ground pin


37 DEC XMUTE O Mute signal output L: mute




42 MEC LIMIT I Sled limit in detection switch signal input

43 MEC LOAD O Loading motor signal output (Load direction)

44 MEC EJECT O Loading motor signal output (Eject direction)

45 MEC INSW I Pack-in detection signal input

46 MEC DSW I Chucking end detection switch signal input

47, 48 MD0, MD1 I CPU operation mode designation signal input (Connect to Vcc.)

49 MD2 I CPU operation mode designation signal input (Connect to Vss.)

50 BUS ON I Bus on signal input L: bus on

51 BU IN I Backup on/off signal input H: backup on, L: backup off

52 CD SBSY I SUBQ sync signal input L: interruption

53 MEC SELFSW I Disc insert detection switch signal input L: disc in interruption


56 UNISI I Serial data signal input

57 UNISO O Serial data signal output

58 UNICKI I Serial clock signal input

59 LINEOFF O Line off signal output

60 A ATT O Audio attenuation signal output H: ATT on

61 EJECT OK I Front panel open signal input H: eject

62 OPEN REQ O Front panel open/close request signal output H: open request

63 MECON O Mechanism deck power supply control signal output

64 CDON O Servo power supply control signal output

36

CDX-S2210/S2210S/S2210X/S2250EE/SW330


65 XUART I Sony-Bus/MC-Bus change signal input H: Sony-Bus, L: MC-Bus

66 ZMUTE O Zero detection mute signal output

67 MECON CHK I MECON rising detection signal input

68 CDON CHK I CDON rising detection signal input


75 RSTX I System reset signal input


77 X1A — Sub-clock connect pin Not used in this set. (Open)

78 X0A — Sub-clock connect pin Not used in this set. (Connect to Vss.)


80 X0 I Main-clock connect pin (12 MHz)

81 X1 O Main-clock connect pin (12 MHz)

82 VCC — Power supply pin (+3.3 V)

83 XTS I Not used in this set. (Open)

84 XINIT3 I Not used in this set. (Open)


86 XSJIG I Not used in this set. (Open)

87 to 89 XINIT0 to 2 I Not used in this set. (Open)


98 XLINE I Not used in this set. (Open)


37

CDX-S2210/S2210S/S2210X/S2250EE/SW330

IC501 MB90487A118 (SYSTEM CONTROL) (MAIN BOARD (3/4))


1 AREA SEL2 I Destination setting pin



4 COL SW I Illumination color select signal input

5 BEEP O Beep signal output

6 NCO O Not used

7 NOSE SW I Front panel open/close detect signal input

8 DIAG I Power AMP status signal input

9 VOL ATT O Electronic volume attenuate control signal output

10 NCO O Not used

11 VSS — Ground

12 TU ATT O Tuner mute control signal output

13 NS MASK O Noise mask signal output

14 ILLUMI SEL1 I Illumination voltage setting pin

15 ILLUMI SEL2 I Illumination voltage setting pin

16 NCO O Not used

17 NCO O Not used

18 NCO O Not used

19 NCO O Not used

20 NCO O Not used

21 NCO O Not used

22 NCO O Not used

23 VCC5 — Power supply pin (+3.3V)

24 EEP SIO I/O EEPROM bus serial data input/output

25 EEP CKO O EEPROM bus serial clock output

26 AMP STB O Power AMP satandby signal output

27 LCD CE O LCD driver chip enable output

28 LCD SO O LCD driver serial data output

29 LCD SCK O LCD driver serial clock output

30 RDS ON O RDS ON signal output

31 NCO O Not used

32 NCO O Not used

33 I2C SCK O I2C bus serial clock output

34 I2C SIO I/O I2C bus serial data input/output

35 DAVDD — A/D converter power supply pin (+3.3V)

36 AVRH — A/D converter reference power supply pin (+3.3V)

37 DAVSS — Ground

38 QUALITY I Noise detect signal input

39 VSM I S-meter voltage detect signal input

40 KEY IN1 I Key signal input

41 KEY IN0 I Key signal input

42 VSS — Ground

43 RC IN0 I Rotary commander key signal input

44 NCO O Not used

45 NCO O Not used

46 NCO O Not used

47 NCO O Not used

48 NCO O Not used

49 MD0 I Operation mode setting pin



52 KEY ACK I Key acknowledgment detect signal input

38

CDX-S2210/S2210S/S2210X/S2250EE/SW330


53 TU ATT IN I Tuner mute zero cross detect signal input

54 BU IN I Back-up power supply detect signal input

55 NCO O Not used

56 DAVN I RDS data block synchronized detect signal input

57 NCO O Not used

58 UNI SI I SONY bus data input

59 UNI SO O SONY bus data output

60 UNI SCK O SONY bus clock output

61 NCO O Not used

62 NCO O Not used

63 NCO O Not used

64 SIRCS I Remote control signal input

65 NCO O Not used

66 NCO O Not used

67 NCO O Not used

68 FLASH W I Memory mode select signal input

69 NCO O Not used

70 NCO O Not used

71 RC IN1 I Rotary commander shift key signal input

72 ACC IN I Accessory power supply detect signal input

73 TEST IN I Test mode detect signal input

74 TEL ATT I Telephone attenuate detect signal input

75 NCO O Not used

76 XKEY ON O A/D converter power supply control signal output

77 RESET I CPU reset input

78 NCO O Not used

79 XOUT — Sub-clock output (32.768kHz)

80 XIN — Sub-clock input (32.768kHz)

81 VSS1 — Ground

82 OSC IN — Main-clock input (3.68MHz)

83 OSC OUT — Main-clock output (3.68MHz)

84 VCC3 — Power supply pin (+3.3V)

85 DEMO SEL I Demo select signal input

86 ATT O Audio mute control signal output

87 BUS ON O Bus ON signal output

88 SYS RST O System reset output

89 EJECT OK SW O Eject OK signal output signal

90 NCO O Not used

91 NCO O Not used

92 NCO O Not used

93 Z-MUTE I CD zero cross mute detect signal input

94 NCO O Not used

95 NCO O Not used

96 NCO O Not used

97 NCO O Not used

98 CD ON I CD servo power control request signal input

99 CDM ON I CD deck power control request signal input

100 NCO O Not used

39

CDX-S2210/S2210S/S2210X/S2250EE/SW330

SECTION 4EXPLODED VIEWS

Ref. No. Part No. Description Remark

4-1. MAIN SECTION


The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

Les composants identifiés par unemarque 0 sont critiques pourla sécurité.Ne les remplacer que par une piéceportant le numéro spécifié.

NOTE:• The mechanical parts with no reference

number in the exploded views are not supplied.• Items marked “*” are not stocked since

they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

• Color Indication of Appearance PartsExample :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinet’s Color• Accessories are given in the last of this

parts list.

R R

F901

not supplied

not supplied

TU1

not supplied

#1

#1

#1

#2

#3

#1

MG-611TA-186//K

A

A

B

B

1

2

3

4

5

6

8

7

1 X-2023-967-1 PANEL (LCD) ASSY, SUB2 2-583-939-01 SCREW (+B 2X4)3 X-2024-365-1 LOCK ASSY (S)4 3-246-006-31 COVER5 2-583-940-01 SCREW (+BTT)

6 1-776-206-21 CORD (WITH CONNECTOR) (POWER) (EXCEPT S2250EE)

6 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)(S2250EE)

7 2-345-298-01 PLATE (TU), GROUND8 A-1083-385-A MAIN BOARD, COMPLETE (S2210/SW330)8 A-1083-453-A MAIN BOARD, COMPLETE (S2210S/S2210X)8 A-1083-614-A MAIN BOARD, COMPLETE (S2250EE)F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A

TU1 A-3220-961-A TUNER UNIT (TUX-032)#1 7-685-792-09 SCREW +PTT 2.6X6 (S)#2 7-685-790-01 SCREW +PTT 2.6X4 (S)#3 7-685-793-09 SCREW +PTT 2.6X8 (S)

40

CDX-S2210/S2210S/S2210X/S2250EE/SW330

4-2. FRONT PANEL SECTION

Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark

51 X-2024-506-1 BUTTON ASSY (S) (S2210X)51 X-2024-531-1 BUTTON ASSY (S) (S2210S/S2250EE)51 X-2025-194-1 BUTTON ASSY (S) (S2210/SW330)52 2-187-736-11 FILTER (IR) (S2210S/S2250EE)52 2-187-736-21 FILTER (IR) (S2210/S2210X/SW330)

53 2-187-738-01 SPRING (RELEASE)54 X-2048-526-1 PANEL SUB ASSY, FRONT (S2210S)54 X-2048-527-1 PANEL SUB ASSY, FRONT (S2210)54 X-2048-528-1 PANEL SUB ASSY, FRONT (S2210X)54 X-2048-529-1 PANEL SUB ASSY, FRONT (S2250EE)

54 X-2048-533-1 PANEL SUB ASSY, FRONT (SW330)55 2-187-737-01 PLATE (CD), LIGHT GUIDE56 1-780-199-11 CONDUCTIVE BOARD, CONNECTION

58

61

61

59

60

57

56

51

not supplied(KEY board)

LCD901

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied 52

5354

55

62 55

57 X-2023-711-1 HOLDER (LCD) ASSY58 2-187-728-01 PANEL, FRONT BACK59 X-2024-133-1 CASE ASSY (for FRONT PANEL)60 A-1083-387-A PANEL COMPLETE ASSY, FRONT (S2210)60 A-1083-455-A PANEL COMPLETE ASSY, FRONT (S2210S)

60 A-1083-603-A PANEL COMPLETE ASSY, FRONT (S2210X)60 A-1083-616-A PANEL COMPLETE ASSY, FRONT (S2250EE)60 A-1092-079-A PANEL COMPLETE ASSY, FRONT (SW330)61 3-250-543-31 SCREW (+B P-TITE M2)62 3-251-320-01 EMBLEM (NO. 2.5), SONY

(S2210/S2210X/SW330)

62 3-251-320-11 EMBLEM (NO. 2.5), SONY (S2210S/S2250EE)LCD901 1-805-765-11 DISPLAY PANEL, LIQUID CRYSTAL

41

CDX-S2210/S2210S/S2210X/S2250EE/SW330

4-3. CD MECHANISM SECTION (1)(MG-611TA-186//K)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

not supplied(SENSOR board)

not supplied

not supplied

not supplied

not supplied

#4

101102

103

104

105

106

107

108

101 A-3372-455-A CHASSIS (T) SUB ASSY102 3-253-729-01 SPRING (LTR), TENSION COIL103 3-253-746-14 SPRING (DAMPER), COMPRESSION104 3-253-746-03 SPRING (DAMPER), COMPRESSION105 2-345-767-01 SPRING (KF60), TENSION

106 3-253-748-01 DAMPER (S)107 3-352-758-31 SCREW (M1.7), TOOTHED LOCK108 A-1075-784-A SERVO BOARD, COMPLETE#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

42

CDX-S2210/S2210S/S2210X/S2250EE/SW330





not supplied

SW4

not supplied

not suppliednot supplied

#5

M902

151152

153

154(including M901)

155

156

157

158

151 A-1075-786-A CHASSIS (OP) COMPLETE ASSY152 3-316-938-91 SCREW (B1.4X5), TAPPING

0153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP)154 A-1075-787-A CHASSIS (OP) SUB ASSY (including M901)155 A-3337-641-A ARM SUB ASSY, CHUCKING

156 A-3337-639-A LEVER (SL) SUB ASSY

157 X-3383-454-3 LEVER (SL) ASSY158 3-261-959-02 SPRING (SL), TORSIONM902 A-3337-638-A MOTOR ASSY, SL (SLED)SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)#5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8

43

CDX-S2210/S2210S/S2210X/S2250EE/SW330



#4

M903

208 210

211

209

207

207

207

201202

203

204

205

206

201 3-262-755-01 WASHER (1.1-2.5)202 2-186-699-11 GEAR (RA1)203 A-1075-789-A ARM ASSY, ROLLER204 3-259-455-02 SPRING (RAL)205 3-253-713-01 SPRING (RAR)

206 3-259-469-01 SPRING (LE), LEAF207 2-134-636-31 SCREW (M1.7X2.5)

208 2-186-696-11 BRACKET (LEM-N)209 3-345-648-91 SCREW (M1.4), TOOTHED LOCK210 A-1083-637-A GEAR (LE) ASSY211 2-186-697-11 BEARING (LEB-N)M903 A-1075-792-A MOTOR ASSY, LE (LOADING)

#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

44

CDX-S2210/S2210S/S2210X/S2250EE/SW330



251

252

252254

255

256

257

253

251 2-186-700-11 GEAR (CHK1)252 3-344-223-01 WASHER253 3-259-470-01 GEAR (LE1)254 3-253-755-02 LEVER (D)

255 3-899-829-01 WASHER (SLIT)256 3-259-032-01 GEAR (LE2)257 A-1075-791-A CHASSIS (M) BLOCK ASSY

45

CDX-S2210/S2210S/S2210X/S2250EE/SW330

SECTION 5ELECTRICAL PARTS LIST

NOTE:• Due to standardization, replacements in

the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.


• RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable

• Items marked “*” are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• SEMICONDUCTORSIn each case, u : µ, for example:uA.. : µA.. uPA.. : µPA..uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORSuF : µF

• COILSuH : µH




When indicating parts by referencenumber, please include the board.

KEY

KEY BOARD**********

1-780-199-11 CONDUCTIVE BOARD, CONNECTION

< CAPACITOR >

C971 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC981 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC982 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC983 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC984 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C985 1-131-664-11 CERAMIC CHIP 0.15uF 10% 10VC986 1-127-715-91 CERAMIC CHIP 0.22uF 10% 10V

< CONNECTOR >

CN901 1-794-312-11 PIN, CONNECTOR 12P

< DIODE >

D901 6-500-886-01 DIODE RSA6.1ENTRD902 8-719-083-66 DIODE UDZSTE-1718BD981 8-719-069-54 DIODE UDZSTE-175.1BD982 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC901 6-707-063-01 IC LC75826WH-US-EIC971 6-600-163-01 IC RS-770 (IR)

< JUMPER RESISTOR >

JP935 1-216-864-11 SHORT CHIP 0JP961 1-216-864-11 SHORT CHIP 0

< LIQUID CRYSTAL DISPLAY >

LCD901 1-805-765-11 DISPLAY PANEL, LIQUID CRYSTAL

< DIODE >

LED931 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT)LED932 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT)LED941 6-500-450-01 LED CL-195SR-CD-T (> M)

(EXCEPT SW330)LED941 6-500-510-01 LED CL-195PG-CD-T (> M) (SW330)LED942 6-500-450-01 LED CL-195SR-CD-T (m .)

(EXCEPT SW330)

LED942 6-500-510-01 LED CL-195PG-CD-T (m .) (SW330)

LED951 6-500-450-01 LED CL-195SR-CD-T (DISC-R) (EXCEPT SW330)LED951 6-500-510-01 LED CL-195PG-CD-T (DISC-R) (SW330)LED952 6-500-450-01 LED CL-195SR-CD-T (DISC-L) (EXCEPT SW330)LED952 6-500-510-01 LED CL-195PG-CD-T (DISC-L) (SW330)

< SWITCH >

LSW901 1-786-805-11 SWITCH, TACTILE (WITH LED) (Z)(EXCEPT SW330)

LSW901 1-786-806-11 SWITCH, TACTILE (WITH LED) (Z) (SW330)LSW902 1-786-805-11 SWITCH, TACTILE (WITH LED) (OFF)

(EXCEPT SW330)LSW902 1-786-806-11 SWITCH, TACTILE (WITH LED) (OFF) (SW330)LSW903 1-786-805-11 SWITCH, TACTILE (WITH LED) (SOURCE)

(EXCEPT SW330)

LSW903 1-786-806-11 SWITCH, TACTILE (WITH LED) (SOURCE)(SW330)

LSW904 1-786-800-11 SWITCH, TACTILE (WITH LED) (VOL -)(EXCEPT SW330)

LSW904 1-786-801-11 SWITCH, TACTILE (WITH LED) (VOL -) (SW330)LSW905 1-786-805-11 SWITCH, TACTILE (WITH LED) (SEL)

(EXCEPT SW330)LSW905 1-786-806-11 SWITCH, TACTILE (WITH LED) (SEL) (SW330)

LSW906 1-786-800-11 SWITCH, TACTILE (WITH LED) (VOL +)(EXCEPT SW330)

LSW906 1-786-801-11 SWITCH, TACTILE (WITH LED) (VOL +) (SW330)LSW907 1-786-805-11 SWITCH, TACTILE (WITH LED) (MODE)

(EXCEPT SW330)LSW907 1-786-806-11 SWITCH, TACTILE (WITH LED) (MODE) (SW330)LSW908 1-786-805-11 SWITCH, TACTILE (WITH LED) (ATT)

(EXCEPT SW330)

LSW908 1-786-806-11 SWITCH, TACTILE (WITH LED) (ATT) (SW330)LSW909 1-786-805-11 SWITCH, TACTILE (WITH LED) (EQ3)

(EXCEPT SW330)LSW909 1-786-806-11 SWITCH, TACTILE (WITH LED) (EQ3) (SW330)LSW910 1-786-800-11 SWITCH, TACTILE (WITH LED)

(SEEK +/> M) (EXCEPT SW330)LSW910 1-786-801-11 SWITCH, TACTILE (WITH LED)

(SEEK +/> M) (SW330)

LSW911 1-786-800-11 SWITCH, TACTILE (WITH LED)(SEEK -/m .) (EXCEPT SW330)

LSW911 1-786-801-11 SWITCH, TACTILE (WITH LED)(SEEK -/m .) (SW330)

LSW913 1-786-805-11 SWITCH, TACTILE (WITH LED) (BTM)(EXCEPT SW330)

LSW913 1-786-806-11 SWITCH, TACTILE (WITH LED) (BTM) (SW330)LSW914 1-786-805-11 SWITCH, TACTILE (WITH LED) (6)

(EXCEPT SW330)

46

CDX-S2210/S2210S/S2210X/S2250EE/SW330


LSW914 1-786-806-11 SWITCH, TACTILE (WITH LED) (6) (SW330)LSW915 1-786-805-11 SWITCH, TACTILE (WITH LED) (5)

(EXCEPT SW330)LSW915 1-786-806-11 SWITCH, TACTILE (WITH LED) (5) (SW330)LSW916 1-786-805-11 SWITCH, TACTILE (WITH LED) (4/SHUF)

(EXCEPT SW330)LSW916 1-786-806-11 SWITCH, TACTILE (WITH LED) (4/SHUF)

(SW330)

LSW917 1-786-805-11 SWITCH, TACTILE (WITH LED) (3/REP)(EXCEPT SW330)

LSW917 1-786-806-11 SWITCH, TACTILE (WITH LED) (3/REP) (SW330)LSW918 1-786-805-11 SWITCH, TACTILE (WITH LED) (2/GROUP +)

(EXCEPT SW330)LSW918 1-786-806-11 SWITCH, TACTILE (WITH LED) (2/GROUP +)

(SW330)LSW919 1-786-805-11 SWITCH, TACTILE (WITH LED) (1/GROUP -)

(EXCEPT SW330)

LSW919 1-786-806-11 SWITCH, TACTILE (WITH LED) (1/GROUP -)(SW330)

LSW920 1-786-805-11 SWITCH, TACTILE (WITH LED) (SENS)(EXCEPT SW330)

LSW920 1-786-806-11 SWITCH, TACTILE (WITH LED) (SENS) (SW330)LSW921 1-786-805-11 SWITCH, TACTILE (WITH LED) (DSPL/DIM)

(EXCEPT SW330)LSW921 1-786-806-11 SWITCH, TACTILE (WITH LED) (DSPL/DIM)

(SW330)

< TRANSISTOR >

Q921 8-729-027-58 TRANSISTOR DTC143ZKA-T146

< RESISTOR >

R901 1-216-819-11 METAL CHIP 680 5% 1/10WR902 1-216-819-11 METAL CHIP 680 5% 1/10WR903 1-216-819-11 METAL CHIP 680 5% 1/10WR904 1-216-821-11 METAL CHIP 1K 5% 1/10WR905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R906 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR907 1-216-819-11 METAL CHIP 680 5% 1/10WR908 1-216-819-11 METAL CHIP 680 5% 1/10WR909 1-216-819-11 METAL CHIP 680 5% 1/10WR910 1-216-821-11 METAL CHIP 1K 5% 1/10W

R911 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR912 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR913 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR914 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR915 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R916 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10WR917 1-216-833-11 METAL CHIP 10K 5% 1/10WR918 1-216-835-11 METAL CHIP 15K 5% 1/10WR919 1-216-837-11 METAL CHIP 22K 5% 1/10WR921 1-216-811-11 METAL CHIP 150 5% 1/10W

(SW330)

R921 1-216-813-11 METAL CHIP 220 5% 1/10W(EXCEPT SW330)

R922 1-216-811-11 METAL CHIP 150 5% 1/10WR925 1-216-807-11 METAL CHIP 68 5% 1/10W

(SW330)R925 1-216-809-11 METAL CHIP 100 5% 1/10W

(EXCEPT SW330)R926 1-216-807-11 METAL CHIP 68 5% 1/10W

R929 1-216-807-11 METAL CHIP 68 5% 1/10W(SW330)


R930 1-216-807-11 METAL CHIP 68 5% 1/10WR933 1-216-811-11 METAL CHIP 150 5% 1/10WR935 1-216-807-11 METAL CHIP 68 5% 1/10W

(SW330)


R936 1-216-805-11 METAL CHIP 47 5% 1/10W(SW330)



R939 1-216-810-11 METAL CHIP 120 5% 1/10W(SW330)

R940 1-216-807-11 METAL CHIP 68 5% 1/10W(SW330)


R943 1-216-807-11 METAL CHIP 68 5% 1/10W(SW330)


R944 1-216-805-11 METAL CHIP 47 5% 1/10W(SW330)


R947 1-216-807-11 METAL CHIP 68 5% 1/10W(SW330)


R948 1-216-805-11 METAL CHIP 47 5% 1/10W(SW330)


R951 1-216-807-11 METAL CHIP 68 5% 1/10W(SW330)



(SW330)R955 1-216-813-11 METAL CHIP 220 5% 1/10W

(EXCEPT SW330)

R956 1-216-811-11 METAL CHIP 150 5% 1/10WR957 1-216-811-11 METAL CHIP 150 5% 1/10WR961 1-216-805-11 METAL CHIP 47 5% 1/10WR962 1-216-805-11 METAL CHIP 47 5% 1/10WR963 1-216-803-11 METAL CHIP 33 5% 1/10W


(SW330)R968 1-216-808-11 METAL CHIP 82 5% 1/10W

(EXCEPT SW330)R972 1-216-809-11 METAL CHIP 100 5% 1/10WR973 1-216-864-11 SHORT CHIP 0

R974 1-216-864-11 SHORT CHIP 0R976 1-216-864-11 SHORT CHIP 0

KEY

47

CDX-S2210/S2210S/S2210X/S2250EE/SW330


R977 1-216-809-11 METAL CHIP 100 5% 1/10WR978 1-216-809-11 METAL CHIP 100 5% 1/10WR979 1-216-809-11 METAL CHIP 100 5% 1/10W

R981 1-216-811-11 METAL CHIP 150 5% 1/10WR982 1-216-811-11 METAL CHIP 150 5% 1/10WR983 1-216-864-11 SHORT CHIP 0R984 1-216-821-11 METAL CHIP 1K 5% 1/10WR985 1-216-821-11 METAL CHIP 1K 5% 1/10W

R986 1-216-821-11 METAL CHIP 1K 5% 1/10WR987 1-216-857-11 METAL CHIP 1M 5% 1/10WR995 1-216-864-11 SHORT CHIP 0

*************************************************************

A-1083-385-A MAIN BOARD, COMPLETE (S2210/SW330)A-1083-453-A MAIN BOARD, COMPLETE (S2210S/S2210X)A-1083-614-A MAIN BOARD, COMPLETE (S2250EE)

*********************

7-621-284-40 +P 2.6X107-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT7-685-793-09 SCREW +PTT 2.6X8 (S)7-685-795-09 SCREW +PTT 2.6X12 (S)

< CAPACITOR >

C4 1-126-947-11 ELECT 47uF 20% 35VC5 1-126-947-11 ELECT 47uF 20% 35VC6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC11 1-164-816-11 CERAMIC CHIP 220PF 2% 50V

C12 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC301 1-128-551-11 ELECT 22uF 20% 63VC302 1-104-665-11 ELECT 100uF 20% 25VC305 1-104-665-11 ELECT 100uF 20% 25V


C343 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC401 1-126-964-11 ELECT 10uF 20% 50VC404 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC405 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC406 1-126-960-11 ELECT 1uF 20% 50V

C407 1-126-960-11 ELECT 1uF 20% 50VC412 1-104-665-11 ELECT 100uF 20% 25VC413 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC431 1-126-964-11 ELECT 10uF 20% 50VC432 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V

C441 1-126-964-11 ELECT 10uF 20% 50VC442 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC451 1-126-964-11 ELECT 10uF 20% 50VC452 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC461 1-126-964-11 ELECT 10uF 20% 50V

C462 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC471 1-126-964-11 ELECT 10uF 20% 50VC474 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC479 1-126-947-11 ELECT 47uF 20% 35VC481 1-126-964-11 ELECT 10uF 20% 50V

C484 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC502 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC503 1-104-665-11 ELECT 100uF 20% 25VC504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C507 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC508 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC509 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC510 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC511 1-104-665-11 ELECT 100uF 20% 25V

C512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC513 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC516 1-216-864-11 SHORT CHIP 0C519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C531 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC601 1-131-868-81 ELECT 3300uF 20% 16VC602 1-165-319-11 CERAMIC CHIP 0.1uF 50VC617 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC618 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

C622 1-126-916-11 ELECT 1000uF 20% 6.3VC623 1-126-916-11 ELECT 1000uF 20% 6.3VC631 1-126-960-11 ELECT 1uF 20% 50VC750 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC751 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

C752 1-126-947-11 ELECT 47uF 20% 35VC753 1-128-551-11 ELECT 22uF 20% 63VC754 1-126-961-11 ELECT 2.2uF 20% 50VC755 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC756 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V

C758 1-126-964-11 ELECT 10uF 20% 50VC759 1-126-964-11 ELECT 10uF 20% 50VC760 1-104-665-11 ELECT 100uF 20% 25VC761 1-126-964-11 ELECT 10uF 20% 50VC763 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V


C774 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC775 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC776 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

< CONNECTOR >

CN601 1-774-701-21 PIN, CONNECTOR 16PCN701 1-794-311-21 PLUG, CONNECTOR 12PCNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P

< DIODE >

D1 8-719-069-55 DIODE UDZSTE-175.6BD479 8-719-988-61 DIODE 1SS355TE-17D502 8-719-060-48 DIODE RB751V-40TE-17D503 8-719-988-61 DIODE 1SS355TE-17D510 6-501-013-01 DIODE BAT54ALT1G

D511 8-719-040-04 DIODE MA721WK-(TX)D512 8-719-040-04 DIODE MA721WK-(TX)D580 8-719-056-84 DIODE UDZ-TE-17-7.5B

KEY MAINVer. 1.3


48

CDX-S2210/S2210S/S2210X/S2250EE/SW330


D581 8-719-083-66 DIODE UDZSTE-1718BD601 8-719-049-38 DIODE 1N5404TU

D609 8-719-978-33 DIODE DTZ-TT11-6.8BD617 8-719-083-66 DIODE UDZSTE-1718BD651 8-719-083-66 DIODE UDZSTE-1718B (S2250EE)D701 6-500-886-01 DIODE RSA6.1ENTRD702 6-500-886-01 DIODE RSA6.1ENTR

D719 8-719-083-66 DIODE UDZSTE-1718BD751 6-500-522-01 DIODE 10EDB40-TA1B2D752 6-500-522-01 DIODE 10EDB40-TA1B2D753 6-500-522-01 DIODE 10EDB40-TA1B2D754 6-500-522-01 DIODE 10EDB40-TA1B2

D755 6-500-522-01 DIODE 10EDB40-TA1B2D756 6-500-522-01 DIODE 10EDB40-TA1B2D757 6-500-522-01 DIODE 10EDB40-TA1B2D758 6-500-522-01 DIODE 10EDB40-TA1B2D759 6-500-522-01 DIODE 10EDB40-TA1B2

D760 6-500-522-01 DIODE 10EDB40-TA1B2D761 6-500-522-01 DIODE 10EDB40-TA1B2D762 6-500-522-01 DIODE 10EDB40-TA1B2D763 8-719-988-61 DIODE 1SS355TE-17D764 8-719-988-61 DIODE 1SS355TE-17

< FERRITE BEAD >

FB1 1-469-844-11 INDUCTOR 2.2uHFB302 1-216-864-11 SHORT CHIP 0FB303 1-469-876-11 INDUCTOR, FERRITE BEADFB304 1-216-295-11 SHORT CHIP 0FB305 1-500-245-11 INDUCTOR, FERRITE BEAD

FB307 1-216-864-11 SHORT CHIP 0FB308 1-500-245-11 INDUCTOR, FERRITE BEADFB309 1-216-864-11 SHORT CHIP 0FB310 1-216-864-11 SHORT CHIP 0FB501 1-500-245-11 INDUCTOR, FERRITE BEAD

FB603 1-216-295-11 SHORT CHIP 0FB604 1-216-295-11 SHORT CHIP 0FB605 1-216-864-11 SHORT CHIP 0FB606 1-414-595-11 INDUCTOR, FERRITE BEAD

< IC >

IC401 6-705-372-01 IC BD3808FS-FE2IC501 6-804-912-01 IC MB90487APF-G-118-BND1IC602 8-759-659-13 IC PST3428ULIC750 6-705-360-02 IC TDA8588BJ/N2/R1

< JACK >

J1 1-815-185-13 JACK (ANTENNA)J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT)

< JUMPER RESISTOR >

JC1 1-216-864-11 SHORT CHIP 0JC12 1-216-864-11 SHORT CHIP 0JC401 1-216-864-11 SHORT CHIP 0JC445 1-216-296-11 SHORT CHIP 0JC446 1-216-864-11 SHORT CHIP 0

JC501 1-216-296-11 SHORT CHIP 0JC503 1-216-296-11 SHORT CHIP 0JC504 1-216-864-11 SHORT CHIP 0

JC506 1-216-864-11 SHORT CHIP 0JC511 1-216-296-11 SHORT CHIP 0

JC527 1-216-821-11 METAL CHIP 1K 5% 1/10WJC533 1-216-864-11 SHORT CHIP 0JC581 1-216-296-11 SHORT CHIP 0JC681 1-216-864-11 SHORT CHIP 0JC753 1-216-296-11 SHORT CHIP 0


< COIL >

L1 1-469-844-11 INDUCTOR 2.2uHL301 1-469-844-11 INDUCTOR 2.2uHL501 1-500-245-11 INDUCTOR, FERRITE BEADL601 1-456-617-11 COIL, CHOKE

< TRANSISTOR >

Q1 8-729-106-68 TRANSISTOR 2SD1615A-GPQ431 6-550-752-01 TRANSISTOR DTC614TKT146Q441 6-550-752-01 TRANSISTOR DTC614TKT146Q451 6-550-752-01 TRANSISTOR DTC614TKT146Q461 6-550-752-01 TRANSISTOR DTC614TKT146

Q471 6-550-752-01 TRANSISTOR DTC614TKT146Q478 1-801-806-11 TRANSISTOR DTC144EKAQ479 8-729-027-23 TRANSISTOR DTA114EKA-T146Q481 6-550-752-01 TRANSISTOR DTC614TKT146Q580 8-729-027-43 TRANSISTOR DTC114EKA-T146

Q581 1-801-806-11 TRANSISTOR DTC144EKAQ582 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q631 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q651 8-729-120-28 TRANSISTOR 2SC1623-L5L6 (S2250EE)Q664 8-729-027-23 TRANSISTOR DTA114EKA-T146

< RESISTOR >

R1 1-216-821-11 METAL CHIP 1K 5% 1/10WR2 1-414-595-11 INDUCTOR, FERRITE BEADR3 1-414-595-11 INDUCTOR, FERRITE BEADR4 1-216-839-11 METAL CHIP 33K 5% 1/10WR5 1-216-843-11 METAL CHIP 68K 5% 1/10W

R12 1-216-864-11 SHORT CHIP 0R13 1-216-864-11 SHORT CHIP 0R301 1-216-821-11 METAL CHIP 1K 5% 1/10WR302 1-216-821-11 METAL CHIP 1K 5% 1/10WR401 1-216-797-11 METAL CHIP 10 5% 1/10W

R405 1-218-881-11 METAL CHIP 27K 0.5% 1/10WR406 1-216-809-11 METAL CHIP 100 5% 1/10WR407 1-216-809-11 METAL CHIP 100 5% 1/10WR408 1-216-809-11 METAL CHIP 100 5% 1/10WR409 1-216-809-11 METAL CHIP 100 5% 1/10W

R410 1-216-809-11 METAL CHIP 100 5% 1/10WR411 1-216-809-11 METAL CHIP 100 5% 1/10WR431 1-216-809-11 METAL CHIP 100 5% 1/10WR432 1-216-841-11 METAL CHIP 47K 5% 1/10WR433 1-216-864-11 SHORT CHIP 0

R441 1-216-809-11 METAL CHIP 100 5% 1/10WR442 1-216-841-11 METAL CHIP 47K 5% 1/10WR443 1-216-864-11 SHORT CHIP 0

MAINVer. 1.3


49

CDX-S2210/S2210S/S2210X/S2250EE/SW330


R451 1-216-809-11 METAL CHIP 100 5% 1/10WR452 1-216-841-11 METAL CHIP 47K 5% 1/10W

R453 1-216-864-11 SHORT CHIP 0R461 1-216-809-11 METAL CHIP 100 5% 1/10WR462 1-216-841-11 METAL CHIP 47K 5% 1/10WR463 1-216-864-11 SHORT CHIP 0R471 1-216-809-11 METAL CHIP 100 5% 1/10W

R472 1-216-841-11 METAL CHIP 47K 5% 1/10WR479 1-216-805-11 METAL CHIP 47 5% 1/10WR481 1-216-809-11 METAL CHIP 100 5% 1/10WR482 1-216-841-11 METAL CHIP 47K 5% 1/10WR501 1-216-864-11 SHORT CHIP 0

R502 1-216-809-11 METAL CHIP 100 5% 1/10WR503 1-216-809-11 METAL CHIP 100 5% 1/10WR504 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR505 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR507 1-216-845-11 METAL CHIP 100K 5% 1/10W

(EXCEPT S2250EE)

R508 1-216-864-11 SHORT CHIP 0R509 1-216-811-11 METAL CHIP 150 5% 1/10WR510 1-216-809-11 METAL CHIP 100 5% 1/10WR511 1-216-809-11 METAL CHIP 100 5% 1/10WR512 1-216-809-11 METAL CHIP 100 5% 1/10W

R513 1-216-845-11 METAL CHIP 100K 5% 1/10WR514 1-216-845-11 METAL CHIP 100K 5% 1/10WR517 1-216-841-11 METAL CHIP 47K 5% 1/10WR518 1-216-864-11 SHORT CHIP 0R519 1-216-845-11 METAL CHIP 100K 5% 1/10W

R521 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR522 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR528 1-216-845-11 METAL CHIP 100K 5% 1/10WR529 1-216-809-11 METAL CHIP 100 5% 1/10WR531 1-216-845-11 METAL CHIP 100K 5% 1/10W

R532 1-216-845-11 METAL CHIP 100K 5% 1/10WR533 1-216-845-11 METAL CHIP 100K 5% 1/10WR534 1-216-833-11 METAL CHIP 10K 5% 1/10WR535 1-216-833-11 METAL CHIP 10K 5% 1/10WR536 1-216-845-11 METAL CHIP 100K 5% 1/10W

R537 1-216-845-11 METAL CHIP 100K 5% 1/10W(S2210S/S2210X)

R538 1-216-845-11 METAL CHIP 100K 5% 1/10W(S2210/S2250EE/SW330)

R539 1-216-821-11 METAL CHIP 1K 5% 1/10WR540 1-216-845-11 METAL CHIP 100K 5% 1/10WR541 1-216-845-11 METAL CHIP 100K 5% 1/10W

R542 1-216-821-11 METAL CHIP 1K 5% 1/10WR543 1-216-821-11 METAL CHIP 1K 5% 1/10WR544 1-216-821-11 METAL CHIP 1K 5% 1/10WR545 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2210S/S2210X)R546 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2210S/S2210X)

R547 1-216-864-11 SHORT CHIP 0R549 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2250EE)R550 1-216-845-11 METAL CHIP 100K 5% 1/10WR551 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2210/SW330)

R556 1-216-833-11 METAL CHIP 10K 5% 1/10W(EXCEPT S2250EE)

R557 1-216-809-11 METAL CHIP 100 5% 1/10WR558 1-216-821-11 METAL CHIP 1K 5% 1/10WR561 1-216-845-11 METAL CHIP 100K 5% 1/10WR563 1-216-845-11 METAL CHIP 100K 5% 1/10WR564 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2250EE)

R565 1-216-845-11 METAL CHIP 100K 5% 1/10WR566 1-216-845-11 METAL CHIP 100K 5% 1/10WR567 1-216-845-11 METAL CHIP 100K 5% 1/10WR568 1-216-821-11 METAL CHIP 1K 5% 1/10WR570 1-216-817-11 METAL CHIP 470 5% 1/10W

R573 1-216-845-11 METAL CHIP 100K 5% 1/10W(S2250EE)



R631 1-249-425-11 CARBON 4.7K 5% 1/4WR632 1-216-841-11 METAL CHIP 47K 5% 1/10WR633 1-216-841-11 METAL CHIP 47K 5% 1/10WR634 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR636 1-216-845-11 METAL CHIP 100K 5% 1/10W





R671 1-216-809-11 METAL CHIP 100 5% 1/10W


R677 1-216-821-11 METAL CHIP 1K 5% 1/10WR679 1-216-821-11 METAL CHIP 1K 5% 1/10WR681 1-216-864-11 SHORT CHIP 0R703 1-216-864-11 SHORT CHIP 0R705 1-216-809-11 METAL CHIP 100 5% 1/10W

R706 1-216-864-11 SHORT CHIP 0R707 1-216-864-11 SHORT CHIP 0R752 1-216-811-11 METAL CHIP 150 5% 1/10WR756 1-216-841-11 METAL CHIP 47K 5% 1/10W

< SWITCH >

S502 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT)(S2210S/S2210X)

S702 1-786-826-11 SWITCH, TACTILE (RESET)

MAIN

50

CDX-S2210/S2210S/S2210X/S2250EE/SW330


< TUNER >

TU1 A-3220-961-A TUNER UNIT (TUX-032)

< VIBRATOR >

X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)

*************************************************************

SENSOR BOARD*************

< SWITCH >

SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)

*************************************************************

A-1075-784-A SERVO BOARD, COMPLETE**********************

< CAPACITOR >

C4 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC5 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC7 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC9 1-104-609-11 ELECT CHIP 100uF 20% 4V

C10 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC13 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC16 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC17 1-162-925-11 CERAMIC CHIP 68PF 5% 50VC18 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V



C32 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC33 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC34 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC35 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC36 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C37 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC38 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC39 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC40 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC41 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V


C49 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC51 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC52 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V


C58 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC59 1-112-195-11 ELECT 47uF 20% 4VC60 1-112-195-11 ELECT 47uF 20% 4VC61 1-126-208-21 ELECT CHIP 47uF 20% 4VC62 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

C64 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC65 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC67 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3VC72 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3VC80 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V

C101 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC102 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC103 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC105 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC106 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

< CONNECTOR >

CN1 1-691-380-21 CONNECTOR, FFC/FPC 16PCN2 1-817-275-21 CONNECTOR, BOARD TO BOARD 28P

< JUMPER RESISTOR >

FB2 1-216-864-11 SHORT CHIP 0FB3 1-216-864-11 SHORT CHIP 0FB4 1-216-864-11 SHORT CHIP 0

< IC >

IC1 6-707-327-01 IC BA5968FP-E2IC2 6-707-328-01 IC TC94A60MFG-301IC3 6-805-086-01 IC MB90487APFV-G-131-BNDE1IC6 6-705-364-01 IC R1114N151D-TR-FA

< TRANSISTOR >

Q1 8-729-904-87 TRANSISTOR 2SB1197K-RQ2 8-729-904-87 TRANSISTOR 2SB1197K-RQ3 8-729-928-90 TRANSISTOR DTC114EE

< RESISTOR >

R1 1-218-941-81 RES-CHIP 100 5% 1/16WR2 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16WR3 1-208-912-11 METAL CHIP 11K 0.5% 1/16WR4 1-218-969-11 RES-CHIP 22K 5% 1/16WR5 1-218-969-11 RES-CHIP 22K 5% 1/16W

R6 1-218-929-11 RES-CHIP 10 5% 1/16WR7 1-218-929-11 RES-CHIP 10 5% 1/16WR8 1-218-967-11 RES-CHIP 15K 5% 1/16WR9 1-218-967-11 RES-CHIP 15K 5% 1/16WR10 1-218-965-11 RES-CHIP 10K 5% 1/16W

R11 1-218-965-11 RES-CHIP 10K 5% 1/16WR12 1-218-977-11 RES-CHIP 100K 5% 1/16WR13 1-218-969-11 RES-CHIP 22K 5% 1/16WR16 1-218-967-11 RES-CHIP 15K 5% 1/16WR17 1-218-973-11 RES-CHIP 47K 5% 1/16W

R19 1-218-967-11 RES-CHIP 15K 5% 1/16WR21 1-218-973-11 RES-CHIP 47K 5% 1/16WR22 1-218-990-11 SHORT CHIP 0R23 1-218-979-11 RES-CHIP 150K 5% 1/16W

SENSOR SERVOMAIN

51

CDX-S2210/S2210S/S2210X/S2250EE/SW330



R24 1-218-962-11 RES-CHIP 5.6K 5% 1/16W

R25 1-218-990-11 SHORT CHIP 0R26 1-218-941-81 RES-CHIP 100 5% 1/16WR28 1-218-947-11 RES-CHIP 330 5% 1/16WR40 1-218-941-81 RES-CHIP 100 5% 1/16WR41 1-218-977-11 RES-CHIP 100K 5% 1/16W

R42 1-218-977-11 RES-CHIP 100K 5% 1/16WR43 1-218-941-81 RES-CHIP 100 5% 1/16WR44 1-218-941-81 RES-CHIP 100 5% 1/16WR45 1-218-989-11 RES-CHIP 1M 5% 1/16WR46 1-218-947-11 RES-CHIP 330 5% 1/16W

R47 1-218-977-11 RES-CHIP 100K 5% 1/16WR48 1-218-941-81 RES-CHIP 100 5% 1/16WR49 1-218-941-81 RES-CHIP 100 5% 1/16WR50 1-218-941-81 RES-CHIP 100 5% 1/16WR51 1-218-941-81 RES-CHIP 100 5% 1/16W

R52 1-218-945-11 RES-CHIP 220 5% 1/16WR53 1-218-941-81 RES-CHIP 100 5% 1/16WR54 1-218-941-81 RES-CHIP 100 5% 1/16WR55 1-218-977-11 RES-CHIP 100K 5% 1/16WR56 1-218-941-81 RES-CHIP 100 5% 1/16W


R62 1-218-977-11 RES-CHIP 100K 5% 1/16WR63 1-218-977-11 RES-CHIP 100K 5% 1/16WR64 1-218-977-11 RES-CHIP 100K 5% 1/16WR65 1-218-941-81 RES-CHIP 100 5% 1/16WR66 1-218-941-81 RES-CHIP 100 5% 1/16W

R67 1-218-941-81 RES-CHIP 100 5% 1/16WR68 1-218-941-81 RES-CHIP 100 5% 1/16WR69 1-218-941-81 RES-CHIP 100 5% 1/16WR70 1-218-941-81 RES-CHIP 100 5% 1/16WR71 1-220-804-11 RES-CHIP 2.2M 5% 1/16W

R72 1-218-941-81 RES-CHIP 100 5% 1/16WR73 1-218-973-11 RES-CHIP 47K 5% 1/16WR74 1-218-941-81 RES-CHIP 100 5% 1/16WR77 1-218-941-81 RES-CHIP 100 5% 1/16WR78 1-218-941-81 RES-CHIP 100 5% 1/16W

R80 1-218-941-81 RES-CHIP 100 5% 1/16WR81 1-218-973-11 RES-CHIP 47K 5% 1/16WR82 1-218-973-11 RES-CHIP 47K 5% 1/16WR83 1-218-973-11 RES-CHIP 47K 5% 1/16WR84 1-218-953-11 RES-CHIP 1K 5% 1/16W

R86 1-218-969-11 RES-CHIP 22K 5% 1/16WR90 1-218-941-81 RES-CHIP 100 5% 1/16WR91 1-218-941-81 RES-CHIP 100 5% 1/16WR100 1-220-200-81 RES-CHIP 30K 5% 1/16WR101 1-218-971-11 RES-CHIP 33K 5% 1/16W

R112 1-218-990-11 SHORT CHIP 0R113 1-218-990-11 SHORT CHIP 0R116 1-218-977-11 RES-CHIP 100K 5% 1/16WR117 1-218-977-11 RES-CHIP 100K 5% 1/16WR118 1-218-977-11 RES-CHIP 100K 5% 1/16W

R119 1-218-977-11 RES-CHIP 100K 5% 1/16W

R120 1-218-990-11 SHORT CHIP 0R121 1-218-990-11 SHORT CHIP 0R122 1-218-990-11 SHORT CHIP 0R123 1-218-990-11 SHORT CHIP 0

R125 1-218-941-81 RES-CHIP 100 5% 1/16WR126 1-218-941-81 RES-CHIP 100 5% 1/16WR127 1-218-941-81 RES-CHIP 100 5% 1/16WR128 1-218-941-81 RES-CHIP 100 5% 1/16WR131 1-216-864-11 SHORT CHIP 0

R132 1-218-962-11 RES-CHIP 5.6K 5% 1/16W

< SWITCH >

SW1 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)

< VIBRATOR >

X1 1-813-371-21 VIBRATOR, CERAMIC (12MHz)X2 1-795-561-21 VIBRATOR, CERAMIC (16.9344MHz)

*************************************************************

MISCELLANEOUS**************

6 1-776-206-21 CORD (WITH CONNECTOR) (POWER)(EXCEPT S2250EE)

6 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)(S2250EE)

0153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP)154 A-1075-787-A CHASSIS (OP) SUB ASSY (including M901)F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A

M902 A-3337-638-A MOTOR ASSY, SL (SLED)M903 A-1075-792-A MOTOR ASSY, LE (LOADING)SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)

*************************************************************

ACCESSORIES************

1-479-077-11 REMOTE COMMANDER (RM-X151)(S2210S/SW330)

2-348-404-11 MANUAL, INSTRUCTION, INSTALL(ENGLISH,FRENCH) (S2210)

2-348-404-31 MANUAL, INSTRUCTION, INSTALL(ENGLISH,RUSSIAN) (S2250EE)

2-348-404-41 MANUAL, INSTRUCTION, INSTALL(ENGLISH,SPANISH,TRADITIONAL CHINESE)

(S2210S/S2210X)2-348-404-51 MANUAL, INSTRUCTION, INSTALL

(ENGLISH,SPANISH) (SW330)

2-348-467-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH)(S2210)

2-348-467-31 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN)(S2250EE)

2-348-467-41 MANUAL, INSTRUCTION(ENGLISH,SPANISH,TRADITIONAL CHINESE)

(S2210S/S2210X)2-348-467-51 MANUAL, INSTRUCTION (ENGLISH,SPANISH)

(SW330)2-548-729-01 LID, BATTERY CASE (for RM-X151)

(S2210S/SW330)

X-2024-133-1 CASE ASSY (for FRONT PANEL)*************************************************************


SERVO

52

CDX-S2210/S2210S/S2210X/S2250EE/SW330

PARTS FOR INSTALLATION AND CONNECTIONS**************************************

301 X-3382-647-1 FRAME ASSY, FITTING302 1-465-459-41 ADAPTOR, ANTENNA (S2250EE)303 1-776-206-21 CORD (WITH CONNECTOR) (POWER)

(EXCEPT S2250EE)304 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)

(S2250EE)305 3-246-011-01 KEY (FRAME)

306 2-187-743-01 COLLAR (S2210/S2210X/SW330)306 2-187-743-11 COLLAR (S2210S/S2250EE)307 A-1082-993-A SCREW ASSY (BS4), FITTING

(S2210S/S2210X/S2250EE)308 3-246-471-01 SCREW (+K 5X8 TP)

301 302

304 305

303

306

308307

2

4


1

US ModelCDX-S2210/SW330




SERVICE MANUALVer. 1.1 2005.05

SUPPLEMENT-1File this supplement with the service manual.

Subject : Production country change.

The CDX-S2210S and CDX-S2250EE models has been changed in the production country to Thailand from Chinese.This service manual, SUPPLEMENT-1 only contains the change.When servicing and inspecting, check the Model Number Label to see if the model is made in Thailand or Chinese.

DISCRIMINATION

CDX-S2210/S2210S/S2210X/S2250EE/SW330

9-879-323-81

MADE IN CHINA

CDX-S2210S ( China production model ) CDX-S2210S ( Thailand production model )

CDX-S2250EE ( China production model ) CDX-S2250EE ( Thailand production model )

2-345-224-0

CLASS 1LASER PRODUCT

MODEL NO.CDX-S2210SSONY

MADE IN THAILAND 2-597-426-0


MODEL NO.CDX-S2210SSONY

MODEL NO.CDX-S2250EESONY

2-345-301-0


MODEL NO.CDX-S2250EESONY

2-633-797-0


2

CDX-S2210/S2210S/S2210X/S2250EE/SW330

TABLE OF CONTENTS

1. DIAGRAMS1-1. Printed Wiring Boards –CD Mechanism Section– .............. 41-2. Schematic Diagram –CD Mechanism Section (1/2)– ......... 51-3. Schematic Diagram –CD Mechanism Section (2/2)– ......... 61-4. Printed Wiring Board –Main Section– ................................ 71-5. Schematic Diagram –Main Section (1/3)– .......................... 81-6. Schematic Diagram –Main Section (2/3)– .......................... 91-7. Schematic Diagram –Main Section (3/3)– ........................ 10

2. EXPLODED VIEWS2-1. Main Section ..................................................................... 142-2. CD Mechanism Section (1) ............................................... 152-3. CD Mechanism Section (2) ............................................... 162-4. CD Mechanism Section (3) ............................................... 172-5. CD Mechanism Section (4) ............................................... 18

3. ELECTRICAL PARTS LIST ........................................ 19

3 3

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

• WAVEFORMS

— SERVO BOARD —

— MAIN BOARD —

• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printedin each block.)

For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• f : internal component.• C : panel designation.

For printed wiring boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• a : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.• CD mechanism (1/2), (2/2) sections no mark : CD PLAY• Main (1/3), (2/3), (3/3) sections no mark : FM

( ) : AM< > : CD PLAY

∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc-tion tolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

• Circled numbers refer to waveforms.• Signal path.

J : CD PLAYF : FMf : AM

Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.

Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.

Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepiéce portant le numérospécifié.

Q

C

These are omitted

EB

EThese are omitted

CB

CThese are omitted

BE

SECTION 1DIAGRAMS

1 IC2 4 (FEI)

Approx.1Vp-p0 V

0.6 Vp-p

16.9344 MHz

Approx. 100 mVp-p



2 IC2 6 (TEI)


6 IC2 oh (FPI2),


Approx. 400 mVp-p

3 IC2 wd (XI)


7 IC3 ia (X1)


1.1 Vp-p

12 MHz

4 IC2 uj (RFI)


5 IC2 of (FNI2),og (FNI1)

1.5 Vp-p

oj (FPI1)

1.5 Vp-p

0 V

0.7 Vp-p

32.768 kHz

2 IC501 ul (XIN)

0.2 V/DIV, 20 µsec/DIV

2 Vp-p

18.432 MHz

3 IC501 id (OSC IN)

1 V/DIV, 0.1 µsec/DIV

44

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

1-1. PRINTED WIRING BOARDS — CD MECHANISM SECTION — : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

SW3

SW2

MAIN BOARD CNP301

TP24

TP40

TP17

TP14

TP18

TP37

TP38

TP39

TP30

FMA4

FMA6

FMA3

TP48

TP49TP51TP53

FMA5C37

C9

C38

C39C40C4

1

C43

C48

C67

C72

FB3

R132

R6

R7

R48

R50

R16

R17

R40

R41

R8

R25 R26

R84

R86

R13

1

R122

Q1

IC6

SW1(DOWN)

C106

R12

0

C65

C64

C19

R12

3

C20

C61

Q3

FB4

C29

C22

R65

C32

C51

C35

C45

C62

R11

R9

C57

R10

IC3

R12

FB2

C6

R11

2

R58

R42

R113

R43

R47

R54R

56R

57R

66

R68

R69

R70

R73 R100

R10

1

R13

R21

R71

Q2

C7

C101

C102

C80

C103

IC1

TP4

TP3

TP5

TP33

TP34

TP35TP

36

TP41

TP42

TP47

TP46

TP25

TP26TP27

TP21

TP22

TP68

TP93

TP15

TP64

FMB3

FMB4

TP11

TP86

TP87

TP10

TP1

TP6

TP7

TP8

TP9

TP12

TP13

TP16

TP20

TP32TP

31

TP66

TP67

TP74

TP75TP76

TP77

TP78

TP79TP80TP81

TP82

TP83

TP84

TP85

TP90

TP89

TP88

TP91

TP92

TP95

TP97TP98

TP99

TP2

TP63

TP44

TP43

TP65

TP62

FMB5

TP101

TP23

TP29

CN1

R4

R24

R5

CN2

R61

C5

R49

R51

R45

R46

R2

R3

X1

X1

IC2

R121

C10

C4

R11

9

C18

C47

C34

R11

8

C17

C23

C42

C16

C60

R125

C36

R62

R117

C21

R116

X2

C24

C31

C28

R12

6

C52

R12

7

C49

R128

C53

R63

R64

C13

R28

R1

C27

R53R55

R67

R60

R74

R77

R78

R80

R81

R82

R83

R90

R91

C33

R19

R22R23

R44

R52

R72R

59

C59

C105

C58

1-864-901-

11

11 1-864-901-

11

11

A

1-689-230-

(Page 7)

Ref. No. LocationIC1 G-2IC2 B-11IC3 D-2IC6 D-1

Q1 B-4Q2 C-1Q3 C-1

• SemiconductorLocation

5 5

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

• Refer to page 3 for Waveforms.1-2. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 11 for IC Block Diagrams.

IC B/D

IC B/D

CN1

R6 R7

TP34

Q2 R86

R84

TP41

TP36

TP27

TP26

TP46

TP30

TP47

R22

R71R72

R64

R62R63

R61R60

R59

R26

R40

R44

C61

R25

R41

TP42

TP12

TP13

TP20

TP21 TP22

TP25

TP18TP17

TP16TP15

TP14

R125

R126R127

R128

TP29

R23

R21

R24

TP93

TP101

R49

C58

C59R131

R113

C5

C27

C23

C20C19

C17

C18

C21

C29

C35C32

C34

C33

C72C80

Q3

C102

C53

C51

C49 C57

C48

C45

C42

FB2

FB3

C67

C60

R52

C52C47

C41

C40

C39

C38

C16

C13

C31

R19

R46R45

FB4

R123

TP35

TP33

C36

R132

R5

R4

R51

R112

Q1

C9

TP37

TP38

TP39

TP40

IC6

R13

IC2

R1

C10

X2

C28

C24

C22

C4

C7

C62

C101

(Page 6)

66

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

IC B/D

(3/3)CNP301

R81

R82

R83

R55 TP

62TP53

TP51

TP49

TP48

TP44

TP65

TP64

TP63

R47

R73

R58

R48

R50

R54

R56

R66

R68

R69

R67

R65

R57

R53

R11

R10

R8

R9

R70

TP32

TP31

TP1

TP2

TP3

TP4

TP5

TP10

TP11

TP43

TP67

TP66

TP23

TP24

R11

6

R11

8

R11

9

R121

TP74

TP75

TP76

TP77

TP78

TP79

TP80

TP81

TP82

TP83

TP84

TP85

TP86

TP87

TP88

TP89

TP90

TP91

TP92

TP97

TP98

TP99

C106

C37

R78

R77

R91

R90

R80

R117R122

R42 R43

R74

R17

R16

C6

R100

R101

IC1

CN2

R12

TP7

TP6

TP9

TP8

SW4

SW1

SW3

SW2

M903

M901

M902

R2

R3

R120

C105

R28

X1

C43

C64

C65

C103

IC3

• Refer to page 3 for Waveforms.1-3. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 12 for IC Block Diagrams.

(Page 5)

(Page 10)

7 7

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

S702RESET

F901

S502

9K

10K

FREQUENCYSELECT

S2210S

S2250EE

C502

R508

R509

R513

R514

C504

C508

C507R510

R511

R512

Q664

R517

R528

C413

R405

R406

R407

R409

R408

D1

C6

R2

R3

R501

C501

R503

R58

2

D580

Q581

R651

R653

R654

D651S2250EE

S2250EE

S2250EE

R60

9

D609

R632R634

R633Q631

R636

Q580

R521

R522

R585

R584

D581

R58

3

R532

R531

JC75

3

C343

R674

R671

R672

R534

R756

C755

R752

C7

R479D479

C770

C769

R1

R536

R535

C404

C405

C756

Q1

R537

R538

R453

R463

FMB3

FMB4

C11

C509R504

R505

R673

L1

R540

R541

C510

C512

C513

C514

C516

R544

R507

R545

R546

JC681

R550

R471

R472

R481

R482

R461

R451

C763

D719

R4

R5

R556

R518

R557

R558

R563

R564

R549

C617

C618

C764C765

C751

C750

C602

R568

C12

C13

JC401

R410R411

R301

R302

C306

C308

C309

C310

FB603

FB605

FB604

R652

C771

R573

FB1 FB309

FB305

FB30

3

FB307

FB308

JC527

C484 C474

JC754

JC75

5

JC446

R533D512

IC602

D51

0

D511

R431 R433

R432

R441

R443

R442

FB302

FB304

C312

R561

R565

R567

R529

R570

R59

0

JC501

JC503

R12

R13

1-865-675-

D702

D701

C519R502

JC445

R462

R452

JC1

FB310

R40

1

JC533

R601

D502 R519

D503JC504

L301

C442

C432

C452

C462

C774C775C776

JC511

S2210SR575

R577

JC505

JC50

6

R566

L501

R542

R543

R547

R578

JC75

6

D763

D764

R539

FB501

FB606

R675R676

R677

R679

R681

D617

R705

C530

C531

FMB6

JC12

C523

Q478

Q651

Q582

Q479

IC40

1

Q43

1

Q44

1

Q47

1

Q481

Q46

1

Q451

IC501

C609

JW10

JW11

JW12

JW13

JW29

JW31

JW32

JW33

JW36

JW37

JW64

JW90

JW101

R63

1

JW10

4

JW10

5

C431C461

C451

JW10

2 C401

CN701

S702

C301

C302

C601

TU1 C761

X502

C758

C752

C441

D75

7

D75

9

D76

0

D60

1

C631

JW9

D75

8

C759

C754

D75

4

C407

C406

JW1

JW2

JW95

JW96

JW97

JW63

JW51

JW52

JW49

S2210S

S2210S

S2250EE

S2250EE

S2250EE

S2250EE

S2210S

JW47

C305

JW91

JW115

JW129

JW130

JW43

JW72

JW94

JW57

C471

C481

JW13

1

JW13

2JW110

D75

5

D75

6

JW27

C760

C753

C479

C412

C4C5

C511

C503

JW59

D761

D762

JW77

JW78

S502

JW3

JW25

JW109

JW144

JW14

5

JW14

6

L601

JW39

CNP301

JW14

2

JW14

3

JW93

JW89

JW81

JW16

JW15

JW14

JW17

JW56

JW50

JW116

JW41

CN601

JW12

0

JW21

JW22

JW11

8

JW24

C622C6

23

JW18

JW128

JW65

JW82

JW75

JW119

JW46

JW14

9

JW45

JW12

7

JW12

5

JW55

JW67

JW58

JW83

X501

JW6

JW8

JW13

7

JW7

JW79

JW30

JW99

JW28 JW117

JW62

JW100

JW92

JW14

1

JW66

JW111

JW147

JW107

JW106

JW113

JW134

JW20

JW14

0

JW73

JW74

JW13

3

JW121

JW80

JW122

JW60

JW15

0

JW15

1

JW44

JW48

JW88JW

126JW

70

JW12

4

JW53

JW68

JW86

J330

JW114

JW38

JW35

JW34

JW40

JW69

JW10

3

JW10

8

JW42 JW

23

JW5

D75

3

D75

2

D75

1

IC750

JW123

JW54

JW139

JW71

JW76

JW84

JW85

JW13

8

JW15

2

JW26

JW98

JW15

3

JW154

YEL

YEL

AUDIOOUT

REARL R

J1(ANTENNA)

21

(21)

1-4. PRINTED WIRING BOARD — MAIN SECTION — : Uses unleaded solder.

(Page 4)

Ref. No. LocationD1 F-3D479 E-6D502 I-8D503 I-5D510 H-8D511 F-6D512 I-8D580 F-11D581 F-11D601 C-10D609 D-8D617 C-9D651 C-9D701 I-3D702 I-3D719 I-4D751 D-7D752 D-7D753 D-7D754 D-7D755 C-5D756 C-6D757 C-6D758 C-6D759 D-8D760 D-8


D761 C-9D762 D-9D763 D-8D764 D-8

IC401 E-3IC501 H-6IC602 I-9IC750 B-6

Q1 F-3Q431 B-4Q441 B-4Q451 C-4Q461 D-4Q471 B-3Q478 E-6Q479 E-5Q481 C-3Q580 F-11Q581 I-10Q582 I-10Q631 H-10Q651 D-8Q664 I-7

Ref. No. Location

88

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

IC B/D

C479

L1

C406

JC445

JC401FB1

JC446

JC12JC1

R405

R406

R407R408

R409

C431

C451

C441

C461

R431

R451

R441

R461

R432

R452

R442

R462

R433

R453

R443

R463

D1

C5

R1

R410

R411

C471

C481

R471

R481

R472

R482

R4

R12

R13

R401

C13

C12

C6

C404

C405

Q481

Q471

Q461

Q441

Q451

C413

Q431

C484 C474

C432

C452

C442

C462

C7

C4 R5

C407

C401

C412

Q479

Q478

TU1

Q1

J1

IC401

R3

R2

J330

C11

1-5. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 12 for IC Block Diagrams.

(Page 10)

(Page 9)

9 9

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

1-6. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 13 for IC Block Diagrams.

IC B/D

S2210S

L601

R633

R632R634

JC756

D764

R479

C631

D751

D752

D753

D754

D755

D756

D757

D758

C753

D75

9

D76

0

R752C758

C759

C760

C761

C752

C754

JC754

C750

R631

JW52

C755

JC753

C763

C769

C770

C776

C751

C775 C765 C764 C774

C617

C618

C601C602 D601

C771

CN601

JC755

D763

D61

7

D76

2

D76

1

D609

D479

Q631

IC750

D651R651

F901

JW53Q651

R654

R653

R652JW98

C609

R609

(Page 8)

(Page 10)

1010

CDX-S2210/S2210S/S2210X/S2250EE/SW330

CDX-S2210/S2210S/S2210X/S2250EE/SW330

R636

R671

R67

2

R512R51

1

C302

R583

D719

R674

C623

D510

D512

R53

4

R55

7

R53

7

R528

D511

R505

R504

R563

R54

4

R522R521

R565

JC527

R54

2

R54

7

R578

R705

R301

R302

FB605

R508

R503

R502

R533

C503

C511

R531

R517

R501

R518

D70

2

R519

R566

R539

R675

R676

R677

R681

R601

D70

1

FB308

C306

FB310

C531

C510

C508 C507

C504

FB501

C513

C501

JC501

C509

C519

FB606

FB604

Q580D581

CN701

FB304

L301

CNP301

FB603

R567

C512

C502

C514

JC504

R561

R53

2

R510R756

R570

R51

3

R51

4

R679

R529

R509

JC505

C308

C310

C309

C305

FB309

C312

C301

C343

IC602

Q664

JC506

X501

L501

D50

2

JC503

C756

JC511

S702

X502

R556

R558 R568

R543

C516

S502

R545

R546

R55

0

JC681

C622

R541 R540

Q581Q582

R585

R584

D580 R582

FB302

FB307

FB303

FB305

D503

R673

IC501

R535JC533

R536R564

C523

R57

5

R53

8

R54

9

R57

3

R50

7

R57

7

R590

1-7. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 3 for Waveforms.

(Page 6)

(Page 8) (Page 9)

11

CDX-S2210/S2210S/S2210X/S2250EE/SW330

1

VREF

VDD

GND

CE

CURRENTLIMIT

2

3

5 VOUT

NC4

IC6 R1114N151D-TR-FA (SERVO Board (1/2))

76

77 EFM SLICE

79

78

82

83

84

88

RFRP

VCOSLCO

RFI

RFRPI

REFQO

RESIN

VRO

VMDIR

TESTR

INVSEL

AGCI

RFDCI

RFO

PNSEL

EQSET

RVDD3

LDO

MDI

RVSS3

FNI2FNI1FPI2FPI1

TPI

TNI

FTE

RFZI

AVSS

3

RFRP FE

ISB

AD/R

FDC

TEI

TEZI

AVDD

3

FOO

TRO

VREF

FMO

DMO

SBSY

SBOK IP

F

SFSY

GPIN

VDD1

5

ZDET

VSS1

5XV

SS3 XI XO

XVDD

3

PVSS

3

VCOR

EF

VCOF

PVRE

FLP

FO

LPFN

TMAX

PDO

PVDD

3

AWRC

VSS1

5VD

D15

LRCK

IBC

KIAI

N

LRCK

OBC

KO

DOUT

PIO3

AOUT

PIO2

PIO1

PIO0

TEST

C

VDDP

VCOIVSSPTESTD

IO1IO0

FGIN

VDDT

STBY

/RST

/CCEBUCKBUS3BUS2BUS1BUS0VSS15

VDDMVDD3VSS3DVSS3

LO

DVR

DVDD3

RO

DVSS3

AUDIOOUT

DIGITALOUT

PLLTMAX

RFEQ

85 AGC

86 RFDC

87 RF

RAMDIGITAL EQAUTO ADJ. ROM

91APC

92

94

FE95

98TE

99

100

21 3 54 6 7 8 9 10 11 12 13 20 21 2214 15 16 17 1918

9697

80VRO

81

89

90

93

23

ANA.LPF

24 25

SYNC SIGNAL PROTECTIONEFM DEMODULATION

69 68 63 62 61 56 55 54 53

50

45

44

43

41403938373635

34333231

30

29

28

27

26

42

4948

4647

60 59 58 57 52 5166 65 6467707475 73

1-BITDAC

CLOCKGEN.PWM

SUBCODEDEMODULATION

CIRCUIT

16KRAM

ADDRESS CIRCUITCPUI/F

CORR

RECT

ION

CIR

CUIT

5-BITR-2R DAC

SERVOCONTROL

10-BITSAR ADC

72 71

CLV SERVO CAV SERVO

AWRC

IC2 TC94A60MFG-301 (SERVO Board (1/2))

• IC BLOCK DIAGRAMS

12

CDX-S2210/S2210S/S2210X/S2250EE/SW330

1

2

11

13

14

12

LEVELSHIFT

LEVELSHIFT

LEVELSHIFT

LEVELSHIFT

MUTE

FWD

FWD

LDCTL

NC

OPOUT1

NC

NC

OPOUT2

POWVCC VCCVOL–

VOL+

VOL2–

VOL2+

VO1–

VO1+

REV

OPIN4+

OPIN4–

OPOUT4

OPIN3+

OPIN3–

OPOUT3

MUTEVOL+GND

VOL3–

VOL3+

VOL4–

VOL4+

REV

OUTR OUTF

10

98

7

6

5

28

27

26

25

24

23

22

212019

18

17

16

15

4

3

IC1 BA5968FP-E2 (SERVO Board (2/2))

32 31 30 29 28 27 26 25 24 23 22

I2C BUSLOGIC

VCO

MIX

FADER(0~-58,-∞dB)

FADER(0~-58,-∞dB)

FADER(0~-58,-∞dB)

FADER(0~-58,-∞dB)


1dB STEP)


1dB STEP)


INPUT SELECTOR(4 STEREO INCLUDE 1 ISOLATION INPUT)


ANTI-ALIASINGFILTER

ANTI-ALIASINGFILTER

MUTE

fc:40kHz fc:40kHz

MUTE

6 7 8 9 10 113 4 521

DGND

AGND FI

L

AN AP2

AP1 B1 B2 C1 C2 D1 D2

DS11

DS21

DS31 NC NC

12 14 1613 15

SDA

SCL

MUT

E

SEL

ADJ

VCC

OUTF

1

OUTR

1

OUTF

2

OUTR

2

DS12

DS22

DS32

OUTS

1

OUTS

2

21 20 19 18 17

VCC

VCC/2

TONEPASS

BASSfo:60,70,80,100,120,140,160,200HzQ:0.5,0.75,1,1.25

MIDDLEfo:500Hz,1kHzQ:1

TABLEfo:5,7.5,10,12.5kHz

TONEPASS

EFFECT (0dB~+20dB,2dB STEP)

EFFECT (0dB~+20dB,2dB STEP) 2ND ORDER

LPF

2ND ORDER LPFfc:OFF,80,120,160HzQ: 0.707



GAIN+ATT(+10~-29,

-∞dB)

IC401 BD3806FS-E2 (MAIN Board (1/3))

13

CDX-S2210/S2210S/S2210X/S2250EE/SW330

MUT

EM

UTE

ENABLELOGIC

STANDBYMUTE

CHIP DETECTDIAGNOSTIC

PROTECTIONDIAGNOSTIC

SWITCH

REGU

LATO

R

SWITCH

REFERENCEVOLTAGE

LOADDUMPPROTECTION

TEMPERATUREPROTECTION

BACK-UPSWITCHREGULATOR

1

3

5

7

9

11

13

15

17

19

21

23

25

27

29

31

33

35

37

2

4

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

TAB

OUT FL-

OUT FL+

OUT RL-

OUT RL+

INRL

SGND

INRR

OUT RR+

OUT RR-

OUT FR+

OUT FR-

DIAG

SW2(ANT REM)

SW1(ANT REM)

REG3(SERVO)

REG4(DR+B)

VP(REG)

REG2(BU 5V)

SDA

SCL

VP2

PGND3

SVR

INFL

INFR

AC GND

PGND2

VP1

STB

PGND1

RST

CRES

REG1(AUDIO +B)

GND(REG)

REG5(ILL)

CBU

FL

RL

RR

VP

FR

I2C BUS

IC750 TDA8588BJ/N2/R1 (MAIN Board (2/3))

14

CDX-S2210/S2210S/S2210X/S2250EE/SW330SECTION 2

EXPLODED VIEWS


2-1. MAIN SECTION










Parts Color Cabinet’s Color• Accessories are given in the last of this

parts list.

R R

F901

not supplied

not supplied

TU1

not supplied

#1

#1

#1

#2

#3

#1

MG-611TA-186//Q

A

A

B

B

1

2

3

5

6

7

4

not supplied

1 X-2023-967-1 PANEL (LCD) ASSY, SUB2 2-583-939-01 SCREW (+B 2X4)3 X-2024-365-2 LOCK ASSY (S)4 2-021-848-01 SHEET (TU), GROUND5 2-050-124-01 SCREW +BTT 2.6X5

6 1-776-206-21 CORD (WITH CONNECTOR) (POWER) (S2210S)6 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)

(S2250EE)

7 A-1115-260-A MAIN BOARD, COMPLETE (S2210S)7 A-1124-781-A MAIN BOARD, COMPLETE (S2250EE)F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10ATU1 A-3220-961-A TUNER UNIT (TUX-032)#1 7-685-792-09 SCREW +PTT 2.6X6 (S)

#2 7-685-790-01 SCREW +PTT 2.6X4 (S)#3 7-685-793-09 SCREW +PTT 2.6X8 (S)

15

CDX-S2210/S2210S/S2210X/S2250EE/SW330

2-2. CD MECHANISM SECTION (1)(MG-611TA-186//Q)



not supplied

not supplied

#4

101102

109

110

103

104

105

106

107

108

101 A-3372-444-A CHASSIS (T) SUB ASSY102 3-253-729-11 SPRING (LTR), TENSION COIL103 3-257-892-12 SPRING (DAMPER), COIL104 3-257-892-01 SPRING (DAMPER), COIL105 2-345-767-11 SPRING (KF60), TENSION

106 3-259-033-01 DAMPER (S)

107 2-587-505-01 SCREW108 A-1082-772-A SERVO BOARD, COMPLETE109 X-3384-088-2 LEVER (L) ASSY110 X-3384-089-2 LEVER (R) ASSY#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

16

CDX-S2210/S2210S/S2210X/S2250EE/SW330



not supplied

SW4

not supplied

not suppliednot supplied

not supplied

#5

M902

151152

153

154(including M901)

155

156

157



156 A-3372-446-A LEVER (SL) SUB ASSY157 X-3384-090-2 LEVER (SL) ASSYM902 A-3372-447-A MOTOR ASSY, SL (SLED)SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)#5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8

17

CDX-S2210/S2210S/S2210X/S2250EE/SW330



#4

M903

208 210

211

209

207

207

207

201202

203

204

205

206

201 3-348-993-01 WASHER202 2-186-699-01 GEAR (RA1)203 A-1075-641-B ARM ASSY, ROLLER204 3-259-455-12 SPRING (RAL)205 3-253-713-11 SPRING (RAR)




18

CDX-S2210/S2210S/S2210X/S2250EE/SW330



251

252

252254

255

256

257

253


255 2-630-962-01 WASHER (SLIT)* 256 2-590-545-01 GEAR (LE2-M)

257 A-1075-640-B CHASSIS (M) BLOCK ASSY

19

CDX-S2210/S2210S/S2210X/S2250EE/SW330SECTION 3

ELECTRICAL PARTS LIST

NOTE:• Due to standardization, replacements in

the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.


• RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable

• Items marked “*” are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• SEMICONDUCTORSIn each case, u : µ, for example:uA.. : µA.. uPA.. : µPA..uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORSuF : µF

• COILSuH : µH




When indicating parts by referencenumber, please include the board.

A-1115-260-A MAIN BOARD, COMPLETE (S2210S)A-1124-781-A MAIN BOARD, COMPLETE (S2250EE)

*********************

7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT7-685-794-09 SCREW +PTT 2.6X10 (S)

< CAPACITOR >

C4 1-126-947-11 ELECT 47uF 20% 35VC5 1-126-947-11 ELECT 47uF 20% 35VC6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC11 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C12 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC301 1-128-551-11 ELECT 22uF 20% 63VC302 1-126-934-11 ELECT 220uF 20% 16VC305 1-104-665-11 ELECT 100uF 20% 25V


C343 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC401 1-126-964-11 ELECT 10uF 20% 50VC404 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC405 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC406 1-126-960-11 ELECT 1uF 20% 50V

C407 1-126-960-11 ELECT 1uF 20% 50VC412 1-126-947-11 ELECT 47uF 20% 35VC413 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC431 1-126-791-11 ELECT 10uF 20% 35VC432 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V

C441 1-126-791-11 ELECT 10uF 20% 35VC442 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC451 1-126-791-11 ELECT 10uF 20% 35VC452 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC461 1-126-791-11 ELECT 10uF 20% 35V

C462 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC471 1-126-791-11 ELECT 10uF 20% 35VC474 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC479 1-126-947-11 ELECT 47uF 20% 35V

C481 1-126-791-11 ELECT 10uF 20% 35VC484 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC502 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC503 1-104-665-11 ELECT 100uF 20% 25V


C511 1-104-665-11 ELECT 100uF 20% 25VC512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC513 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC516 1-216-845-11 METAL CHIP 100K 5% 1/10W

C519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC523 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

(S2250EE)C531 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC601 1-131-868-81 ELECT 3300uF 20% 16VC602 1-165-319-11 CERAMIC CHIP 0.1uF 50V

C609 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC617 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC618 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC622 1-126-916-11 ELECT 1000uF 20% 6.3VC623 1-126-916-11 ELECT 1000uF 20% 6.3V

C631 1-126-960-11 ELECT 1uF 20% 50VC750 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC751 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC752 1-126-947-11 ELECT 47uF 20% 35VC753 1-128-551-11 ELECT 22uF 20% 63V

C754 1-126-961-11 ELECT 2.2uF 20% 50VC755 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC756 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC758 1-126-964-11 ELECT 10uF 20% 50VC759 1-126-964-11 ELECT 10uF 20% 50V

C760 1-104-665-11 ELECT 100uF 20% 25VC761 1-126-964-11 ELECT 10uF 20% 50VC763 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC764 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC765 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

C769 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC770 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC771 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC774 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

MAIN

20

CDX-S2210/S2210S/S2210X/S2250EE/SW330



< CONNECTOR >

CN601 1-774-701-21 PIN, CONNECTOR 16PCN701 1-794-311-21 PLUG, CONNECTOR 12PCNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P

< DIODE >

D1 8-719-036-94 DIODE RD5.6SB-T1D479 8-719-081-97 DIODE MMDL914T1D502 6-500-137-01 DIODE BAT54HT1D503 8-719-081-97 DIODE MMDL914T1D510 6-501-013-01 DIODE BAT54ALT1G

D511 6-501-051-01 DIODE BAT54CLT1GD512 6-501-051-01 DIODE BAT54CLT1GD580 8-719-056-83 DIODE UDZ-TE-17-6.8BD581 8-719-056-93 DIODE UDZ-TE-17-18BD601 8-719-049-38 DIODE 1N5404TU

D609 8-719-056-83 DIODE UDZ-TE-17-6.8BD617 8-719-056-93 DIODE UDZ-TE-17-18BD651 8-719-056-93 DIODE UDZ-TE-17-18B (S2250EE)D701 6-500-886-01 DIODE RSA6.1ENTRD702 6-500-886-01 DIODE RSA6.1ENTR

D719 8-719-056-93 DIODE UDZ-TE-17-18BD751 6-500-522-01 DIODE 10EDB40-TA1B2D752 6-500-522-01 DIODE 10EDB40-TA1B2D753 6-500-522-01 DIODE 10EDB40-TA1B2D754 6-500-522-01 DIODE 10EDB40-TA1B2

D755 6-500-522-01 DIODE 10EDB40-TA1B2D756 6-500-522-01 DIODE 10EDB40-TA1B2D757 6-500-522-01 DIODE 10EDB40-TA1B2D758 6-500-522-01 DIODE 10EDB40-TA1B2D759 6-500-522-01 DIODE 10EDB40-TA1B2

D760 6-500-522-01 DIODE 10EDB40-TA1B2D761 6-500-522-01 DIODE 10EDB40-TA1B2D762 6-500-522-01 DIODE 10EDB40-TA1B2D763 8-719-081-97 DIODE MMDL914T1D764 8-719-081-97 DIODE MMDL914T1

< FERRITE BEAD >

FB1 1-469-844-11 INDUCTOR 2.2uHFB302 1-469-876-11 INDUCTOR, FERRITE BEADFB303 1-469-876-11 INDUCTOR, FERRITE BEADFB304 1-500-245-11 INDUCTOR, FERRITE BEADFB305 1-216-295-11 SHORT CHIP 0

FB307 1-469-876-11 INDUCTOR, FERRITE BEADFB308 1-500-245-11 INDUCTOR, FERRITE BEADFB309 1-216-864-11 SHORT CHIP 0FB310 1-216-864-11 SHORT CHIP 0FB501 1-500-245-11 INDUCTOR, FERRITE BEAD

FB603 1-216-295-11 SHORT CHIP 0FB604 1-216-295-11 SHORT CHIP 0FB605 1-216-864-11 SHORT CHIP 0FB606 1-414-595-11 INDUCTOR, FERRITE BEAD

< IC >

IC401 6-705-372-01 IC BD3808FS-FE2IC501 6-804-912-01 IC MB90487APF-G-118-BNDE1IC602 8-759-659-13 IC PST3428ULIC750 6-705-360-02 IC TDA8588BJ/N2/R1

< JACK >

J1 1-815-185-13 JACK (ANTENNA)J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR)

< JUMPER RESISTOR >



JC511 1-216-296-11 SHORT CHIP 0JC527 1-216-821-11 METAL CHIP 1K 5% 1/10WJC533 1-216-864-11 SHORT CHIP 0JC681 1-216-864-11 SHORT CHIP 0JC753 1-216-296-11 SHORT CHIP 0


< RESISTOR >

JW52 1-249-425-11 CARBON 4.7K 5% 1/4W

< COIL >

L1 1-469-844-11 INDUCTOR 2.2uHL301 1-216-295-11 SHORT CHIP 0L501 1-500-245-11 INDUCTOR, FERRITE BEADL601 1-456-617-11 COIL, CHOKE 250uH

< TRANSISTOR >

Q1 8-729-920-85 TRANSISTOR 2SD1664-QRQ431 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ441 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ451 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ461 6-551-070-01 TRANSISTOR KRC283S-B-RPK/P

Q471 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ478 8-729-421-19 TRANSISTOR UN2213Q479 8-729-424-08 TRANSISTOR UN2111Q481 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ580 8-729-421-22 TRANSISTOR UN2211

Q581 8-729-421-19 TRANSISTOR UN2213Q582 8-729-010-25 TRANSISTOR MSD601-RT1Q631 8-729-010-25 TRANSISTOR MSD601-RT1Q651 8-729-010-25 TRANSISTOR MSD601-RT1 (S2250EE)Q664 8-729-424-08 TRANSISTOR UN2111

MAIN

21

CDX-S2210/S2210S/S2210X/S2250EE/SW330


< RESISTOR >

R1 1-216-821-11 METAL CHIP 1K 5% 1/10WR2 1-414-595-11 INDUCTOR, FERRITE BEADR3 1-414-595-11 INDUCTOR, FERRITE BEADR4 1-216-839-11 METAL CHIP 33K 5% 1/10WR5 1-216-843-11 METAL CHIP 68K 5% 1/10W

R12 1-216-864-11 SHORT CHIP 0R13 1-216-864-11 SHORT CHIP 0R301 1-216-821-11 METAL CHIP 1K 5% 1/10WR302 1-216-821-11 METAL CHIP 1K 5% 1/10WR401 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R405 1-218-881-11 METAL CHIP 27K 0.5% 1/10WR406 1-216-809-11 METAL CHIP 100 5% 1/10WR407 1-216-809-11 METAL CHIP 100 5% 1/10WR408 1-216-809-11 METAL CHIP 100 5% 1/10WR409 1-216-809-11 METAL CHIP 100 5% 1/10W

R410 1-216-809-11 METAL CHIP 100 5% 1/10WR411 1-216-809-11 METAL CHIP 100 5% 1/10WR431 1-216-809-11 METAL CHIP 100 5% 1/10WR432 1-216-841-11 METAL CHIP 47K 5% 1/10WR433 1-216-864-11 SHORT CHIP 0

R441 1-216-809-11 METAL CHIP 100 5% 1/10WR442 1-216-841-11 METAL CHIP 47K 5% 1/10WR443 1-216-864-11 SHORT CHIP 0R451 1-216-809-11 METAL CHIP 100 5% 1/10WR452 1-216-841-11 METAL CHIP 47K 5% 1/10W

R453 1-216-864-11 SHORT CHIP 0R461 1-216-809-11 METAL CHIP 100 5% 1/10WR462 1-216-841-11 METAL CHIP 47K 5% 1/10WR463 1-216-864-11 SHORT CHIP 0R471 1-216-809-11 METAL CHIP 100 5% 1/10W

R472 1-216-841-11 METAL CHIP 47K 5% 1/10WR479 1-216-805-11 METAL CHIP 47 5% 1/10WR481 1-216-809-11 METAL CHIP 100 5% 1/10WR482 1-216-841-11 METAL CHIP 47K 5% 1/10WR501 1-216-864-11 SHORT CHIP 0

R502 1-216-809-11 METAL CHIP 100 5% 1/10WR503 1-216-809-11 METAL CHIP 100 5% 1/10WR504 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR505 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR507 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2210S)

R508 1-216-811-11 METAL CHIP 150 5% 1/10WR509 1-216-864-11 SHORT CHIP 0R510 1-216-809-11 METAL CHIP 100 5% 1/10WR511 1-216-809-11 METAL CHIP 100 5% 1/10WR512 1-216-809-11 METAL CHIP 100 5% 1/10W

R513 1-216-845-11 METAL CHIP 100K 5% 1/10WR514 1-216-845-11 METAL CHIP 100K 5% 1/10WR517 1-216-841-11 METAL CHIP 47K 5% 1/10WR518 1-216-864-11 SHORT CHIP 0R519 1-216-845-11 METAL CHIP 100K 5% 1/10W

R521 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR522 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR528 1-216-845-11 METAL CHIP 100K 5% 1/10W


R535 1-216-833-11 METAL CHIP 10K 5% 1/10WR536 1-216-845-11 METAL CHIP 100K 5% 1/10WR537 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2210S)R538 1-216-845-11 METAL CHIP 100K 5% 1/10W

(S2250EE)R539 1-216-821-11 METAL CHIP 1K 5% 1/10W


R545 1-216-845-11 METAL CHIP 100K 5% 1/10W(S2210S)

R546 1-216-845-11 METAL CHIP 100K 5% 1/10W(S2210S)

R547 1-216-864-11 SHORT CHIP 0R549 1-216-845-11 METAL CHIP 100K 5% 1/10W


R556 1-216-845-11 METAL CHIP 100K 5% 1/10W(S2210S)

R557 1-216-809-11 METAL CHIP 100 5% 1/10WR558 1-216-821-11 METAL CHIP 1K 5% 1/10WR561 1-216-845-11 METAL CHIP 100K 5% 1/10WR563 1-216-845-11 METAL CHIP 100K 5% 1/10W



R570 1-216-817-11 METAL CHIP 470 5% 1/10WR573 1-216-845-11 METAL CHIP 100K 5% 1/10W


(S2210S)R577 1-216-845-11 METAL CHIP 100K 5% 1/10WR578 1-216-821-11 METAL CHIP 1K 5% 1/10W

R582 1-216-821-11 METAL CHIP 1K 5% 1/10WR583 1-216-821-11 METAL CHIP 1K 5% 1/10WR584 1-216-841-11 METAL CHIP 47K 5% 1/10WR585 1-216-849-11 METAL CHIP 220K 5% 1/10WR590 1-216-864-11 SHORT CHIP 0

R601 1-216-845-11 METAL CHIP 100K 5% 1/10WR609 1-216-821-11 METAL CHIP 1K 5% 1/10WR631 1-249-425-11 CARBON 4.7K 5% 1/4WR632 1-216-841-11 METAL CHIP 47K 5% 1/10W

MAIN

22

CDX-S2210/S2210S/S2210X/S2250EE/SW330


R633 1-216-841-11 METAL CHIP 47K 5% 1/10WR634 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR636 1-216-845-11 METAL CHIP 100K 5% 1/10WR651 1-216-821-11 METAL CHIP 1K 5% 1/10W


(S2250EE)



R671 1-216-809-11 METAL CHIP 100 5% 1/10WR672 1-216-809-11 METAL CHIP 100 5% 1/10WR673 1-216-833-11 METAL CHIP 10K 5% 1/10W


R681 1-216-864-11 SHORT CHIP 0R705 1-216-809-11 METAL CHIP 100 5% 1/10WR752 1-216-811-11 METAL CHIP 150 5% 1/10WR756 1-216-841-11 METAL CHIP 47K 5% 1/10W

< SWITCH >

S502 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT)(S2210S)

S702 1-692-431-21 SWITCH, TACTILE (RESET)

< TUNER >

TU1 A-3220-961-A TUNER UNIT (TUX-032)

< VIBRATOR >

X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)

*************************************************************

SENSOR BOARD**************

< SWITCH >

SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)

*************************************************************

A-1082-772-A SERVO BOARD, COMPLETE**********************

< CAPACITOR >

C4 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC5 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC7 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC9 1-104-609-11 ELECT CHIP 100uF 20% 4V

C10 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC13 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC16 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC17 1-162-925-11 CERAMIC CHIP 68PF 5% 50VC18 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V



C32 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC33 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC34 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC35 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC36 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V




C58 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC59 1-126-208-21 ELECT CHIP 47uF 20% 4VC60 1-112-195-11 ELECT 47uF 20% 4VC61 1-126-208-21 ELECT CHIP 47uF 20% 4VC62 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

C64 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC65 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC67 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3VC72 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3VC80 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V

C101 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC102 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC103 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC105 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC106 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

< CONNECTOR >

CN1 1-691-380-21 CONNECTOR, FFC/FPC 16PCN2 1-817-275-21 CONNECTOR, BOARD TO BOARD 28P

< JUMPER RESISTOR >

FB2 1-216-864-11 SHORT CHIP 0FB3 1-216-864-11 SHORT CHIP 0FB4 1-216-864-11 SHORT CHIP 0

< IC >

IC1 6-707-327-01 IC BA5968FP-E2IC2 6-707-328-01 IC TC94A60MFG-301

MAIN SENSOR SERVO

23

CDX-S2210/S2210S/S2210X/S2250EE/SW330


IC3 6-805-086-02 IC MB90487APFV-G-142-BNDE1IC6 6-705-364-01 IC R1114N151D-TR-FA

< TRANSISTOR >

Q1 8-729-904-87 TRANSISTOR 2SB1197K-RQ2 8-729-904-87 TRANSISTOR 2SB1197K-RQ3 8-729-928-90 TRANSISTOR DTC114EE

< RESISTOR >

R1 1-218-941-81 RES-CHIP 100 5% 1/16WR2 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16WR3 1-208-912-11 METAL CHIP 11K 0.5% 1/16WR4 1-218-969-11 RES-CHIP 22K 5% 1/16WR5 1-218-969-11 RES-CHIP 22K 5% 1/16W


R11 1-218-965-11 RES-CHIP 10K 5% 1/16WR12 1-218-977-11 RES-CHIP 100K 5% 1/16WR13 1-218-969-11 RES-CHIP 22K 5% 1/16WR16 1-218-967-11 RES-CHIP 15K 5% 1/16WR17 1-218-973-11 RES-CHIP 47K 5% 1/16W

R19 1-218-967-11 RES-CHIP 15K 5% 1/16WR21 1-218-973-11 RES-CHIP 47K 5% 1/16WR22 1-218-990-81 SHORT CHIP 0R23 1-218-979-11 RES-CHIP 150K 5% 1/16WR24 1-218-962-11 RES-CHIP 5.6K 5% 1/16W

R25 1-218-990-81 SHORT CHIP 0R26 1-218-941-81 RES-CHIP 100 5% 1/16WR28 1-218-947-11 RES-CHIP 330 5% 1/16WR40 1-218-941-81 RES-CHIP 100 5% 1/16WR41 1-218-977-11 RES-CHIP 100K 5% 1/16W

R42 1-218-977-11 RES-CHIP 100K 5% 1/16WR43 1-218-941-81 RES-CHIP 100 5% 1/16WR44 1-218-941-81 RES-CHIP 100 5% 1/16WR45 1-218-989-11 RES-CHIP 1M 5% 1/16WR46 1-218-947-11 RES-CHIP 330 5% 1/16W

R47 1-218-977-11 RES-CHIP 100K 5% 1/16WR48 1-218-941-81 RES-CHIP 100 5% 1/16WR49 1-218-941-81 RES-CHIP 100 5% 1/16WR50 1-218-941-81 RES-CHIP 100 5% 1/16WR51 1-218-941-81 RES-CHIP 100 5% 1/16W

R52 1-218-945-11 RES-CHIP 220 5% 1/16WR53 1-218-941-81 RES-CHIP 100 5% 1/16WR54 1-218-941-81 RES-CHIP 100 5% 1/16WR55 1-218-977-11 RES-CHIP 100K 5% 1/16WR56 1-218-941-81 RES-CHIP 100 5% 1/16W


R62 1-218-977-11 RES-CHIP 100K 5% 1/16WR63 1-218-977-11 RES-CHIP 100K 5% 1/16WR64 1-218-977-11 RES-CHIP 100K 5% 1/16WR65 1-218-941-81 RES-CHIP 100 5% 1/16W

R66 1-218-941-81 RES-CHIP 100 5% 1/16WR67 1-218-941-81 RES-CHIP 100 5% 1/16WR68 1-218-941-81 RES-CHIP 100 5% 1/16WR69 1-218-941-81 RES-CHIP 100 5% 1/16WR70 1-218-941-81 RES-CHIP 100 5% 1/16W

R71 1-220-804-11 RES-CHIP 2.2M 5% 1/16WR72 1-218-941-81 RES-CHIP 100 5% 1/16WR73 1-218-973-11 RES-CHIP 47K 5% 1/16WR74 1-218-941-81 RES-CHIP 100 5% 1/16WR77 1-218-941-81 RES-CHIP 100 5% 1/16W


R84 1-218-953-11 RES-CHIP 1K 5% 1/16WR86 1-218-969-11 RES-CHIP 22K 5% 1/16WR90 1-218-941-81 RES-CHIP 100 5% 1/16WR91 1-218-941-81 RES-CHIP 100 5% 1/16WR100 1-220-200-81 RES-CHIP 30K 5% 1/16W

R101 1-218-971-11 RES-CHIP 33K 5% 1/16WR112 1-218-990-81 SHORT CHIP 0R113 1-218-990-81 SHORT CHIP 0R116 1-218-977-11 RES-CHIP 100K 5% 1/16WR117 1-218-977-11 RES-CHIP 100K 5% 1/16W

R118 1-218-977-11 RES-CHIP 100K 5% 1/16WR119 1-218-977-11 RES-CHIP 100K 5% 1/16WR120 1-218-990-81 SHORT CHIP 0R121 1-218-990-81 SHORT CHIP 0R122 1-218-990-81 SHORT CHIP 0

R123 1-218-990-81 SHORT CHIP 0R125 1-218-941-81 RES-CHIP 100 5% 1/16WR126 1-218-941-81 RES-CHIP 100 5% 1/16WR127 1-218-941-81 RES-CHIP 100 5% 1/16WR128 1-218-941-81 RES-CHIP 100 5% 1/16W

R131 1-216-864-11 SHORT CHIP 0R132 1-218-962-11 RES-CHIP 5.6K 5% 1/16W

< SWITCH >

SW1 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)

< VIBRATOR >

X1 1-813-371-21 VIBRATOR, CERAMIC (12MHz)X2 1-795-561-21 VIBRATOR, CERAMIC (16.9344MHz)

*************************************************************

MISCELLANEOUS***************

6 1-776-206-21 CORD (WITH CONNECTOR) (POWER) (S2210S)6 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)

(S2250EE)0153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP)

154 A-1075-645-A CHASSIS (OP) SUB ASSY (including M901)F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A

M902 A-3372-447-A MOTOR ASSY, SL (SLED)M903 A-1075-643-A MOTOR ASSY, LE (LOADING)SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)

*************************************************************

SERVO

24

CDX-S2210/S2210S/S2210X/S2250EE/SW330


ACCESSORIES************

1-479-077-12 REMOTE COMMANDER (RM-X151) (S2210S)2-348-404-61 MANUAL, INSTRUCTION, INSTALL (ENGLISH,

SPANISH,TRADITIONAL CHINESE,FRENCH)(S2210S)

2-348-404-81 MANUAL, INSTRUCTION, INSTALL (ENGLISH,RUSSIAN) (S2250EE)

2-348-467-61 MANUAL, INSTRUCTION (ENGLISH,SPANISH,TRADITIONAL CHINESE,FRENCH) (S2210S)

2-348-467-81 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN)(S2250EE)

2-548-729-01 LID, BATTERY CASE (for RM-X151) (S2210S)X-2024-133-3 CASE ASSY (for FRONT PANEL)

*************************************************************

PARTS FOR INSTALLATION AND CONNECTIONS***************************************

301 X-3382-647-1 FRAME ASSY, FITTING302 1-465-459-31 ADAPTOR, ANTENNA (S2250EE)303 1-776-206-21 CORD (WITH CONNECTOR) (POWER) (S2210S)304 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)

(S2250EE)305 3-246-471-01 KEY (FRAME)

306 2-187-743-11 COLLAR307 X-3381-154-1 SCREW ASSY (BS4), FITTING308 3-349-410-11 BUSHING

301 302

304 305

303

306

308307

× 2

× 4

SERVICE MANUAL

CDX-S2210/S2210S/S2210X/S2250EE/SW330

US ModelCDX-S2210/SW330




SUPPLEMENT-2File this supplement with the service manual.

Subject : Change of CD mechanism.

Ver. 1.2 2005.07

This model provides three types of CD mechanisms.Check the label on the chassis (T) when servicing the CD mechanism.

9-879-323-82

DISCRIMINATION

B T A s s s s s s s s

Model Name

FactoryB : MG-611TA-186//Q (Refer to Supplement-1)D : MG-611TA-186//K (Refer to Service Manual)E : MG-611TA-186//C (Refer to Supplement-2)

2

CDX-S2210/S2210S/S2210X/S2250EE/SW330

EXPLODED VIEWS








Parts Color Cabinet’s Color• Accessories are given in the last of this parts list.

R R

101 A-1088-624-A CHASSIS (T) SUB ASSY102 A-1092-999-A SERVO BOARD, COMPLETE103 2-345-865-11 SPRING (DAMPER), COMPRESSION (BLACK)104 2-345-865-01 SPRING (DAMPER), COMPRESSION (NATURAL)

105 2-345-767-21 SPRING (KF60), TENSION106 3-253-748-11 DAMPER (S)107 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

1. CD MECHANISM SECTION (1)(MG-611TA-186//C)


not supplied

not supplied

not supplied

not supplied

#4

101

103

104

105

106

107

102



3

CDX-S2210/S2210S/S2210X/S2250EE/SW330




156 A-1088-613-A LEVER (SL) SUB ASSY157 X-2024-784-2 LEVER (SL) ASSY

158 3-261-959-21 SPRING (SL), TORSION159 3-253-736-21 SPRING (CHKG), TENSION160 3-264-165-21 SCREW161 3-253-742-21 WHEEL (SL), WORMM902 A-1088-614-A MOTOR ASSY, SL (SLED)

SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)#5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8


not supplied

SW4

not supplied

#5

M902

151152

158

159160

161

153

154(including M901)

155

156

157

4

CDX-S2210/S2210S/S2210X/S2250EE/SW330


201 3-262-755-11 WASHER (1.1-2.5)202 2-186-699-21 GEAR (RA1)203 A-1088-618-A ARM ASSY, ROLLER204 3-259-455-21 SPRING (RAL)205 3-253-713-21 SPRING (RAR)





#4

M903

208 210

211

209

207

207

207

201202

203

204

205

206

5

CDX-S2210/S2210S/S2210X/S2250EE/SW330



255 3-899-829-01 WASHER (SLIT)256 2-590-545-21 GEAR (LE2-M)257 A-1088-620-A CHASSIS (M) BLOCK ASSY258 3-262-755-11 WASHER (1.1-2.5)


251

252258

252254

255

256

257

253

6

CDX-S2210/S2210S/S2210X/S2250EE/SW330

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision1.0 2004.12 New1.1 2005.05 Production country change. (Supplement-1) (ENG-05003)

1.2 2005.07 Change of CD mechanism. (Supplement-2) (ECN-ECB00626)

1.3 2005.11 NOTE FOR REPLACEMENT OF THE IC501 is added. (SPM-05015)

service manual us model - diagramas dediagramas.diagramasde.com/otros/cdx-s2210x.pdfservice manual...

Documents