service manuall lg-tv 42px3rv

PLASMA TVSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : MF-056A

MODEL : 42PX3RV/RVB42PX3RV/RVB-ZA

website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html

- 2 -

CONTENTS

SAFETY PRECAUTIONS ....................................................................................3

DESCRIPTION OF CONTROLS ..........................................................................4

SPECIFICATIONS................................................................................................9

ADJUSTMENT INSTRUCTIONS .......................................................................11

TROUBLE SHOOTING GUIDE..........................................................................15

BLOCK DIAGRAM.............................................................................................24

EXPLODED VIEW..............................................................................................26

EXPLODED VIEW PARTS LIST ........................................................................27

REPLACEMENT PARTS LIST...........................................................................28

SCHEMATIC DIAGRAM.........................................................................................

PRINTED CIRCUIT BOARD ..................................................................................

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.

It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.

When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

POWERMUTE

TV/AV MULTIMEDIA

LIST ARC MENU

PR

PR

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM PIP/DW SLEEP

REVEAL TEXT/PIP PR+

WIN. SIZE MIXPIP PR-

POSITION TIMESWAP

HOLD INDEXPIP INPUT

?

i

I/II

MULTIMEDIASelects the Component, RGB or DVI

modes.switches the set on from standby.

PIP/DWSwitches the sub picture on or off.

Selects PIP or DW modes.PIP PR + /-

Selects a programme for the sub picture.SWAP

Alternates between main and sub pic-ture.

PIP INPUTSelects the input mode for the sub pic-

ture.WIN.SIZE

Adjusts the sub picture size.POSITION

Moves the sub picture to DD / EE or FF / GGdirection.

POWERswitches the set on from standby oroff to standby.

ARC Changes the picture format.

MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.

SWAPReturns to the previously viewedprogramme.Note : This function works onlywhen Favourite programme is set toOff. Otherwise each press of this but-ton will select a stored favorite pro-gramme.

SSMTo select the sound appropriate toyour viewing programme character.

NUMBER buttons

SLEEPSets the sleep timer.

I/IISelects the language during dual lan-guage broadcast.Selects the sound output.

TEXT/*These buttons are used for teletext.For further details, see the ÔTeletextÕsection.Note : In teletext mode, the PIP PR+/-, SWAP and PIP INPUT buttons areused for teletext function.

LISTDisplays the programme table.

TV/AVSelects the TV, AV, Component, RGB

or DVI modes.switches the set on from standby.

MUTESwitches the sound on or off.

DD / EE (Programme Up/Down)selects a programme or a menu item.

switches the set on from standby.FF / GG (Volume Up/Down)

adjusts the volume.adjusts menu settings.

OKaccepts your selection or displays the

current mode.

PSMAdjusts the factory preset picture

according to the room.

SPLIT ZOOMEnlarge the screen with regular

ration.

- 4 -

DESCRIPTION OF CONTROLS

- 5 -

<Front Panel Controls>

PRVOLMENUTV/AV OK

PRVOLMENUTV/AV OK

1 32 4 5 6 7

1. Remote Control Sensor

2. Power IndicatorIlluminates red in standby mode, Illuminates green when theset is turned on.

3. Power ButtonSwitches the set on from standby or off to standby.

4. TV/AV ButtonSelects the TV, AV, Component, RGB or HDMI modes. Switches the set on from standby.

5. MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.

6. OKAccepts your selection or displays the current mode.

7. DD / EE (Programme Up/Down)Selects a programme or a menu item.Switches the set on from standby.FF / GG (Volume Up/Down)Adjusts the volume.Adjusts menu settings.

- 6 -

<Back Panel>

S-VIDEO

VID

EO

AU

DIO

RL/

MO

NO

A/V INPUT2A/V INPUT2

AC INPUT

RS-232C INPUT(CONTROL/SERVICE)

S-VIDEOS-VIDEO

(MONO)

AUDIO AUDIO

L R

AUDIO AUDIO

L R

AUDIO AUDIO

L R

Antenna

VIDEO VIDEO

REMOTECONTROL

HDMI/DVI(VIDEO) AUDIO INPUT RGB INPUT

VIDEOVIDEO

COMPONENTCOMPONENT INPUT INPUT 2 2

COMPONENTCOMPONENT INPUT INPUT 1 1

MONITMONITOR OUTPUTOR OUTPUT

A/V INPUTA/V INPUT 1 1

VVARIABLE ARIABLE AUDIO OUTAUDIO OUT

1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER, DVD or STB to this socket.Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or theEMI Filter core along with separate cable.

2. CONTROL LOCK / REMOTE CONTROL

3. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.

4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.

5. VIDEO/AUDIO IN/OUT SOCKETS (A/V INPUT 1)Connect the video/audio out sockets of external equipmentto these sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in A/V INPUT 1.

6. VARIABLE AUDIO OUTPUT

7. ANTENNA INPUT

8. POWER CORD SOCKETThis the set operates on an AC power. The voltage is indicat-ed on the Specifications page. Never attempt to operate theset on DC power.

9. AUDIO/VIDEO INPUT (A/V INPUT 2)S-VIDEO/AUDIO IN SOCKETS

1 42 3 5 7 86

9

- 7 -

RGB / HDMI mode

Resolution

640x350

720x400

640x480

848x480

800x600

HorizontalFrequency(KHz)

VerticalFrequency(Hz)

852x480

832x624

1024x768

1152x864

1152x870

1280x960

1280x1024

70.09

85.08

70.08

85.03

59.94

66.66

72.80

75.00

85.00

60.00

70.00

75.00

60.00

70.00

75.00

56.25

60.31

72.18

75.00

85.06

74.55

60.00

70.06

75.02

85.00

60.05

70.01

75.00

75.06

60.02

60.02

31.468

37.861

31.469

37.927

31.469

35.000

37.861

37.500

43.269

31.500

37.799

39.375

31.500

37.799

39.375

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.677

54.348

63.995

67.500

68.681

60.023

63.981

- 8 -

AS mark

LG TV

OwnerÕs Manual

1.5V1.5V

Alkaline batteries Power Cord

POWERMUTE

TV/AV MULTIMEDIA

LIST ARC MENU

PR

PR

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM PIP/DW SLEEP

REVEAL TEXT/PIP PR+

WIN. SIZE MIXPIP PR-

POSITION TIMESWAP

HOLD INDEXPIP INPUT

?

i

I/II

Remote Control handset

- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.

- Contract your dealer for buying these items.

Optional Extras

AccessoriesAccessories

Tilt wall mounting bracket Video cables Audio cablesCeiling mounting bracket

40

4250

42

40

- Secure the TV assembly by joinning it to a wall by using the Eye Bolts/Wall brackets.

Joinning the TV assembly to the wall to protect the set tumbling

¥ After the set must be mounted on a desktop, install the Eye Bolts on the set asshown.Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 2 bolts, (not supplied with the product),as shown.Match the height of the Eye Bolts and the wall brackets. Check to be sure the brackets are tightened securely.

¥ Secure the TV assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.

2-Wall brackets

2-Eye Bolts

SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.

- 9 -

V Application RangeThis spec is applied to the 42ÓPDP TV used MF-056A Chassis.

V Specification

Each part is tested as below without special appointment.1) Temperature : 25±5¡C (77±9¡F), CST : 40±52) Relative Humidity: 65±10%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)

* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification

Safety: CE, IEC specificationEMC : CE, IEC

V General Specification

1. Module Specification

Remark

Safety : IEC/EN60065, EMI : EN55013, EMS : EN55020

Model Name

42PX3RV-ZA

Market

EU

Remark

PDP

LGE SPEC

Maker : SONY/ Sanken

Specification

42 inch wide Color Display Module

16:9

PDP42V7xxxx

RGB Closed Type, Film Filter

1) Temp : 0~40 deg

2) Humidity : 0~85%

1) Temp : -20~60 deg

2) Humidity : 0~85%

100-240V~, 50/60Hz

No

1

2

3

4

5

6

Item

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

2. Model Specification (42PX3RV-ZA)

- 10 -

Item

Market

Broadcasting system

Available Channel

Receiving system

SCART Jack(3EA)

Video Input (2EA)

S-Video Input(3EA)

Component Input(1EA)

RGB Input(1EA)

HDMI Input(1EA)

Audio Input(4EA)

Wired Control

Audio variable out

No

1

2

3

4

5

6

7

8

9

10

11

12

13

Specification

EU

PAL B/G/I/D/K, NTSC

BAND PAL NTSC

VHF/UHF C1~C69 2~83

CATV S1~S47 1~71

Upper Heterodyne

PAL, SECAM, NTSC

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

RGB-DTV

HDMI-PC

HDMI-DTV

PC Audio, Component(1EA), AV(2EA)

Remark

4 System : PAL, SECAM, NTSC,PAL60



L/R Input

- 11 -

ADJUSTMENT INSTRUCTIONS

1. Application ObjectThese instructions apply to the MF-056A Chassis.

2. Specification(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolationtransformer will help protect test instrument.

(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of

25±5¡C of temperature and 65±10% of relative humidity ifthere is no specific designation.

(4) The input voltage of the receiver must keep 100-220V,50/60Hz.

(5) The receiver must be operated for about 15 minutes priorto the adjustment.

O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.

O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE

PATTERN.

[ Set is activated HEAT-RUN without signal generator inthis mode.

[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.

Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), afterimage may be occur in the black level part of thescreen.

3. Channel memory

3-1. Setting up the LGIDS1) Install the LGIDS. (idsinst.exe)2) After installation, restart your PC.3) Extract [files.zip] to folder [c:\LGIDS\files].4) Start LGIDS.

3-2. Channel memory Method 1) Select ÒPDPÓ and ÒHurricaneÓ on Model dialog. And check

your connection in Communication dialog. (If yourconnection is ÔNGÕ, then set your PORT(COM1,2,3,...)correctly.)

2) Connect RS-232C cable and turn on the power.(If your connection has completed, you can see ÒReadyÓ.)

[ If your set is not an end products but only a board, youhave to make your board to Stand-by state (LED_R). Andyou have to Download in Stand_by power state.

3) Select proper CH_memory file(*.nvm) for each model at[NVRAM Download] $ [Write Batch]Next, select proper binary file(*.bin) including the CHinformation for each model at [NVRAM File].

4) Click the [Download] button.It means the completion of the CH memory download if allitems show ÔOKÕ and Status is changed by ÔPASSÕ at thelower right corner of the window.

5) If you want to check whether the CH information ismemorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CHinformation downloaded.

3-3 Sub program download

1) Select ÒPDPÓ and ÒHurricaneÓ on Model dialog. And checkyour connection in Communication dialog. (If yourconnection is ÔNGÕ, then set your PORT(COM1,2,3,...)correctly.)(Fig. 1)

(Fig. 3)

(Fig. 3-1)

- 12 -

2) Connect RS-232C cable and turn on the power. (Use thespecial Cable For Sub-program) (If your connection hascompleted, you can see ÒReadyÓ)

4. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage Adjustments)

4-1. Test Equipment : D.M.M. 1EA

4-2. Adjustment Method[P/No 3501V00220A(Sanken PSU) B/D]

(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P807, connect

- terminal to GND pin of P807.3) After turning RV501, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)

(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P807, connect

Ð terminal to GND pin of P805.2) After turning RV401, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)

5. EDID (The Extended DisplayIdentification Data)/ DDC (DisplayData Channel) download

5-1. Required Test Equipment1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID

TESTER Ver.2.5)2) A Jig for EDID Download3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable

5-2. Setting of device

5.3. Preparation for Adjustment1) As above Fig. 5, Connect the Set, EDID Download Jig, PC

& Cable.2) Turn on the PC & EDID Download Jig. And Execute the

S/W : EDID TESTER Ver,2.53) Set up S/W option

Repeat Number : 5Device Address : A0PageByte : 8

4) Power on the Set

5.4. Sequence of Adjustment

(1) DDC data of Analog-RGB1) Init the data

2) Load the EDID data.(Open File)[Analog-RGB : MF056A_RGB.ANA][digital(HDMI) : MF056A_DMI.DVI]

3) Set the S/W as below.4) Push the ÒWrite Data & VerifyÓbutton. And confirm ÒYesÓ.5) If the writing is finished, you will see the ÒOKÓ message.

Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)

(Fig. 4) Connection diagram of power adjustment for measuring

(Fig. 5) Connection Diagram of DDC download

- 13 -

6. Auto AV(CVBS) Color Balance

6-1. Required- This AV color balance adjustment should be performed beforwhite Balance Adjustment

6-2. Required Equipment1) Remote controller for adjustment2) AV Pattern Generator

: 802F Pattern Generator, Master(MSPG-925FA), etc(Which has PAL Composite Video format output withstandard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)

6-3. Method of Auto Color Balance1) Input the PAL Composite Video (Fig6. 100% Color Bar

Pattern) into video input.(42PX4RV-TA : AV1/AV2 Input 50Hz,42PX4RV-ZA : AV4/AV5 Input)

2) Set the PSM to Standard mode in Picture menu.3) Press INSTAR key on R/C for adjustment.4) Press the G(Vol. +) key operate to set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

7. Adjustment of White Balance

7-1. Required Equipment1) Remote controller for adjustment2) Color Analyzer (CA-100 or same product)3) Auto W/B adjustment instrument(only for auto adjustment)4) AV Pattern Generator

7-2. Connecting diagram of equipment formeasuring (For Auto Adjustment)

W Auto adjustment Map(RS-232C)

7-3. Adjustment of White Balance

O Operate the zero-calibration of the CA-100, then sticksensor to PDP module surface when you adjust.

O For manual adjustment, it is also possible by the followingsequence.

1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operate heatrun more than 15 minutes.

2) As below Fig.7-1, Supply 216Level (85 IRE) full screenpattern to Video input.(42PX4RV-TA : AV1/AV2 INPUT 50Hz,42PX4RV-ZA : AV4/AV5 INPUT)

3) Press the TV/AV KEY on R/C for converting input mode.4) Set the PSM to Standard mode in Picture menu.5) Enter the White Balance adjustment mode by pressing the

INSTART key twice(White Balance) on R/C.6) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and offset) using D / E(CH +/-) keyon R/C.

7) Adjust Only High Light with R Gain/ B Gain using F / G(VOL+/-) key on R/C.

8) Adjust it until color coordination becomes as below.(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset7E, B Offset 80 is Fixed)[MF-056A : 42PX4RV-TA/ZA] - VGA 42ÓBright : High Light : 80 ± 20cdColor-Coordinate : High Light : X : 0.285 ± 0.003

Y : 0.295 ± 0.003Color Temperature : 9,300¡K ± 500¡K

9) When adjustment is completed, Exit adjustment modeusing EXIT key on R/C

(Fig. 7-1) Pattern for Adjustment of White Balance

216 Level (85 IRE)

Type

Baud Rate

115200

Index

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Data bit

8

Cmd1 Cmd2

j a

j b

j c

j d

j e

j f

Stop bit

1

Parity

NONE

MF-056A : RT-42PX40/ RZ-42PX40

ProtocolSetting

Data Min Value

00(00)

00(00)

00(00)

00(00)

00(00)

00(00)

Max Value

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern

(Fig. 7) Connection Diagram of Auto W/B adjustment

MSPG-2100 /MSTG- 5200

216 Level (85 IRE)

COLORANALYZERTYPE ; CA-100

CVBSsignalinput

RS-232C Serial Communication

- 14 -

8. Auto Component Color Balance

8-1. Required Test Equipment1) Remote controller for adjustment2) 802F Pattern Generator

(Which has 720p Ypbpr output & PC 1024x768 60Hz withStandard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.8)

8-2. Method of Auto Component Color Balance1) Input the Component 720p 100% Color Bar signal into

Component1 or Component2.2) Set the PSM to Standard mode in Picture menu.3) Press INSTART key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means complete adjustment

9. Auto RGB Color Balance

9-1. Required Test Equipment1) Remote controller for adjustment2) 802F Pattern Generator, Master (MSPG-925FA), etc.

(Which has XGA 60Hz PC Format output with standard(0.7Vpp) horizontal black and white pattern as Fig.10)

9-2. Method of Auto RGB Color Balance1) Input the PC 1024x768 60Hz horizontal black and white

pattern into RGB.2) Set the PSM to Standard mode in Picture menu.3) Press ADJ key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

9. Default Value in Adjustment mode

9-1. Auto Color Balance (Component/RGB)

9-2. White Balance

Level : 0

Level : 255

(Fig. 9) Auto RGB Color Balance Test Pattern

(Fig. 10) Default Value on OSD

(Fig. 10-1) Default Value on OSD

Auto Color Balance(HEX)

Auto-RGB) G To SetRed ) Offset1)) 80Green)Offset1)) 80Blue) Offset1)) 80Red) Offset2)) 80Green)Offset2)) 80Blue) Offset2)) 80Red) Gain)) 80Green)Gain)) 80Blue) Gain)) 80Reset)) G To Set

White Balance(Hex)

Red ) Gain)) 80Red ) Offset)) 80Green)Gain)) 80Green)Offset)) 80Blue) Gain)) 80Blue) Offset)) 80Reset)) G To Set

(Fig. 8) Auto Component Color Balance Test Pattern

- 15 -

TROUBLE SHOOTING GUIDE

1. Power Board

1-1. The whole flowchart which it follows in voltage output state

Start check

Manufacture enterprisemeaning of a passage

1. Check the Power Offcondition.

Doesn't the screen whole come

out?

It is identical with Power Off

condition?

Yes

Yes

No

No

No

No

No

2. Check the Interfacesignal condition.

Is the Interface signal operated?

Yes

3. Check the St-by 5Vsignal circuit.

Doesn't the low pressure output

come out?

Doesn't the St-by 5V signal

come out?

Yes

Yes

No

4. Check the 5V Monitorsignal circuit.

Doesn't the 5V Monitor signal

come out?

Yes

7. Check the VSC Vs-ONsignal

Doesn't the high tension output

come out?

Doesn't the VSC signal Vs-ON

come out?

Yes

Yes

Doeshigh tension

output voltage dropoccur?

When theY B/D Module

Input Connector isremoved, does output

voltage Drop occurs?

When theY,Z B/D Module

input connector is remove,does Power B/D hightension

output voltage dropoccur?

Yes No No

9. Check the PowerBoard Output high

tension circuit

Yes

10. Check the Z B/DModule output circuit

Yes

When theZ B/D Module

Input Connector isremoved, does output

voltage Drop occurs?

11. Check the Y B/DModule output circuit

Yes

No

8. Check the Vs, Vavoltage output circuit.

Doesn't the Vs, Va voltage output

come out?

Yes

No

No

5. Check the VSC RL-ONsignal.

Doesn't the VSC signal RL-ON

come out?

Yes

6. Check the VSC lowpressure output

Doesn't the VSC low pressureoutput come out?

Yes

- 16 -

1-2. Sony Power Board Structure

1 2 3

T502: Vs Trans

T702: Va Trans

T101: St-by Trans

T103: Low Voltage Trans

- 17 -

1-3. Sanken Power Board Structure

1 2 3

T221: Vs Trans

T271: Va Trans

T121: St-by Trans

T201: Low Voltage Trans

- 18 -

2. No Power

(1) Symptom¯ DoesÕt minute discharge at module. ¯ Non does not come in into the front LED.

(2) Check following

Is plug in power cord? Plug in power cord.

Yes

No

Is the Line Filter and Power BoardCable connected?

Connect the Cable.

Yes

No

Is the Fuse(F101) normal on PowerBoard ?

Replace the Fuse.

Yes

No

Is the Power Board and 7P of VSCBoard Cable connected?

Connect the Cable.

Yes

No

After the cable connect isremoved to Power Board(exceptthe CN101 connection cable), theAC voltage marking is authorizedon manual. When ST-BY 5V is notoperated, replace Power Board.

- 19 -

3. Protect Mode

(1) Symptom¯ After once shining, it does not discharge minutely

from module¯ The Rely falls(The sound is audible ÒclickÓ) ¯ It is converted with the color where the front LED

is red from green.

(2) Check following

Is the Power Boardnormal?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replace theconnector.

Replace Y-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Boardnormal?

Replace X-Board.

Is the output voltage normalafter remove P1, 2, 4, 9, 10

connector of Ctrl-B/D?

Yes

No Yes

Is the Y- Boardnormal?

Is the output voltagenormal after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)

Yes

No Yes Yes

Replace Z-Board.

Is the Z- Boardnormal?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)

Yes

No Yes

Is the X- Boardnormal?

Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of

X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D

Yes

No Yes

Is the VSC Boardnormal?

Is the output voltage normalafter remove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, 1100 normaloperation: Replace VSC Board

Yes

No

Is the COF of X, Y, Znormal?

No

Yes

Yes

- 20 -

4. No Raster

(1) Symptom¯ DoesÕt minute discharge at module. ¯ It maintains the condition where the front LED is green.

(2) Check following

Is the Power Boardnormal?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replaceconnector.

Replace Y-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Boardnormal?

Replace X-Board.


connector of Ctrl-B/D?

Yes

No Yes

Is the Y- Boardnormal?

Is normal the outputvoltage after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)

Yes

No Yes Yes

Replace Z-Board.

Is the Z- Boardnormal?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is the Fuse(FS1, FS2) on Z-B/Dnormal? (In case of open is replace)

Yes

No Yes

Is the X- Boardnormal?


connector of X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D

Yes

No Yes


Is the output voltage normalafter remove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, P1100 normaloperation: Replace VSC Board

Yes

No

Is the COF of X, Y, Znormal?

No

Yes

Yes

- 21 -

5. In case of occurring strange screen into specific mode

5-1. In case the OSD does not displayed

(1) Symptom¯ LED is green¯ The minute discharge continuously becomes accomplished from module

(2) Check following

Is the LVDS cablenormal?


Is the LVDS cableconnected well?

Cable inserts well.Yes

No

No

Yes

Does the FIL8532IC(IC800) Operates ?

Replace FIL8532IC(IC800).

No

Is the Ctrl Board ofModule normal?

Replace Ctrl B/D.No

No

YesReplace VSC B/D

Replace the cable.Yes

- 22 -

5-2. In case of doesÕt display the screen into specific mode

(1) Symptom¯ The screen does not become the display from specific input mode

(RF, AV, Component, RGB, DVI).

(2) Check following¯ Check the all input mode should become normality display.¯ Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become

normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode

(4) In the case of becomes unusual display from RF, AV mode

(5) In the case of becomes unusual display from Component, RGB mode

(6) In the case of becomes unusual display from HDMI mode

Is the Tuner normal?

Is the CXA2069Qnormal?

Is the Tuner Cableconnected well?

Cable inserts well.Yes

No

No

Yes

Is the FIL8532normal?

Replace the Tuner

No

Is normal the Input voltage, IICCommunication and CVBS output?

Yes

Is the Input voltage, IICCommunication and HV

sync normal?

NoReplace the IC

No


sync normal?

NoReplace the IC

No

Is the CXA2069Qnormal?

Yes



sync normal?

NoReplace the IC

No


sync normal?

NoReplace the IC

No



sync normal?

NoReplace the IC

No

Is the Sil9011normal?

Yes



sync normal?

NoReplace the IC

No


sync normal?

NoReplace IC

No

- 23 -

6. In case of no sound

(1) Symptom¯ LED is green¯ Screen display but sound is not output

(2) Check following

Is the SPK cablenormal?

Is the SPK cableconnected well?

Cable inserts well.

No

No

Replace IC400

No

Replace IC401

No

Replace SPK cableYes

Yes

Is the RF/ AV/Component/ RGB/

HDMI soundnormal?

No Does IC400Operates ?

Does IC401Operates ?

Replace IC402

No

Does IC402Operates ?

Replace VSC B/D

Yes Yes

- 24 -

BLOCK DIAGRAMca

ble

'

MEMO

- 25 -

- 26 -

EXPLODED VIEW

300

301

304

302

202206

203

204

201

205

580

410

530

121

601600

120

501

401

400

303

207

200

520

430

- 27 -

120 6401VD0032A SPEAKER ASSEMBLY, FULL RANGE(R) RZ-42PX30 FILM TYPE

121 6401VD0033A SPEAKER ASSEMBLY, FULL RANGE(L) RZ-42PX30 FILM TYPE

200 6348Q-E080W PDP, 42Ó 852*480 PDP42V70102.ADLGB

201 6871QCH053A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V7 FPGA

202 6871QDH084A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV TOP B/D

203 6871QDH085A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV BTM B/D

204 6871QLH047A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42V7 XL B/D

205 6871QRH055A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42V7 XR B/D

206 6871QYH036A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V7

207 6871QZH041A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V7

300 3091V00816D CABINET ASSEMBLY, RZ-42PX31 STEREO MF056C FILM TYPE SKD

3091V00816H CABINET ASSEMBLY, 42PX3RVB STEREO RF052C FILM TYPE SKD

301 4980V01203B SUPPORTER, ASSY AL FILTER TOP RZ-42PX30 C/SKD

302 4980V01204B SUPPORTER, ASSY AL FILTER BOTTOM RZ-42PX30 C/SKD

303 4980V01205B SUPPORTER, ASSY AL FILTER RIGHT RZ-42PX30 C/SKD

304 4980V01206B SUPPORTER, ASSY AL FILTER LEFT RZ-42PX30 C/SKD

400 3809V00605B BACK COVER ASSEMBLY, 42PX17/30 CHASSIS CHANGE C/SKD

3809V00605G BACK COVER ASSEMBLY, 42PX3RVB CHASSIS CHANGE BK SPRAY

401 3301V00085A PLATE ASSEMBLY, ASSY 3300V00552A RZ-42PX30 PLATE TUNER COVER

3301V00085E PLATE ASSEMBLY, ASSY 3300V00552A 42PX3RVB PLATE TUNER COVER BK

410 4980V01071B SUPPORTER, ASSY AL VERTICAL RZ-42PX10 SKD

430 3501V00216E BOARD ASSEMBLY, ASSY AP-42DX30 MF056C C/SKD

3501V00216F BOARD ASSEMBLY, ASSY AP-42DX30 MF056C BK C/SKD

501 3301V00083A PLATE ASSEMBLY, ASSY 3300V00550A 3301V00084A 42PX17/30 PLATE TUNER

3301V00083G PLATE ASSEMBLY, ASSY 42PX3RVB BK PRESS AV PLATE

520 6871VMMF71A PWB(PCB) ASSEMBLY,MAIN MF-056A RZ-42PX31 SUSAB SKD

530 6871VSMS36B PWB(PCB) ASSEMBLY,SUB CONT MF056C RZ-42PX30 SKD NO VINYL

580 6709V00010A POWER SUPPLY ASSEMBLY, PDP 42INCH MF056A 350W YPSU-J006A

600 6871VSMS18B PWB(PCB) ASSEMBLY,SUB A/V MF056A RT/RZ-42PX40 SIDE A/V SUSAB

601 4811V00118A BRACKET ASSEMBLY, DECO RZ-42PX10 RF043B SIDE AV

4811V00118N BRACKET ASSEMBLY, SIDE AV 42PX3RVB-ZA AF044A BLACK

EXPLODED VIEW PARTS LIST

No. Part No. Descriptions

MIC39100 MICREL 3P SOT223 R/TP

BA033FP-E2 ROHM 3P-SOP,TO252-3

KA7809R, FAIRCHILD 2P D-PAK, R/TP

SC156515M-1.8TR SEMTECH 5P/TO-263-5





SC156515M-1.8TR SEMTECH 5P/TO-263-5

KIA78R05F KEC 5PIN DPAK R/TP 1A,5V

SC156515M-1.8TR 5P/TO-263-5


SII9011CLU(PB FREE) SILICON IMAGE 128P

AT24C02N-10SI-2.7 ATMEL 8P SOIC

MC34063ADR2G ON SEMI SO-8P

CXA2069Q QFP64 BK I2C BUS AV S/W

LA7217M MFP14 TP SYNC SEPARATOR

MSP4410K MICRONAS 80P/PQFP

NSP-2100A,LF NEOFIDELITY TQFP

TAS5122DCAR 56P/TSSOP R/TP 30W

KA4558D 8SOP OP AMP

74HC14D 14SOP TP SHITTER TRIGGER

AT24C02N-10SI-2.7 ATMEL 8P SOIC

74HC14D 14SOP TP SHITTER TRIGGER

ICL3232CBNZ INTERSIL 16P/SOP R/TP

FLI8125AA-LF GENESIS 208P/PQFP

AT24C32AN-10SI-2.7 ATMEL 8PIN SOP

SST25VF040-20-4C-S2AE-T SST SOIC 8P

FLI8532BC-LF GENESIS 416P/PBGA

24LC256-I/SM 8P,SOP TP 256K IIC

K4D261638F-LC50,LF TSOPII 66P

K4D261638F-LC50,LF TSOPII 66P

BSS83 TP PHILIPS N-CHANNEL S/W TR






CHIP 2SC3875S(ALY) KEC








KRA102S R/TP KEC SOT23 CHIP TR



REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

Q104

Q1200

Q200

Q201

Q202

Q203

Q204

Q205

Q206

Q207

Q300

Q301

Q302

Q303

Q304

Q305

Q400

Q401

Q402

Q403

Q404

Q405

Q407

Q408

Q409

Q410

Q411

D1005

D1006

D1007

D1008

D1009

D1010

D1012

D1013

D102

D103

D104

D105

D106

D108

D1100

D1105

D1106

D1107

D1109

D1110

D112

D113

D114

D1200

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR387500AA

0TR150400BA

0TR150400BA

0TR387500AA

0TR150400BA

0TR150400BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR102008AA

0TR387500AA

0TR102008AA

0TR387500AA

0TR387500AA

0TR387500AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD200009AF

0DD200009AF

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD184009AA



CHIP 2SA1504S(ASY) KEC

























KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

RU2M V(1) TP SANKEN

RU2M V(1) TP SANKEN

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS184 TP KEC - 85V - 300MA


IC1000

IC1001

IC1002

IC1003

IC1004

IC1005

IC1100

IC1101

IC1102

IC1103

IC1104

IC1105

IC1200

IC1201

IC202

IC300

IC301

IC400

IC401

IC402

IC403

IC404

IC500

IC502

IC600

IC700

IC701

IC703

IC800

IC802

IC901

IC902

IC1202

IC1203

IC200

IC201

IC503

IC504

Q100

Q1000

Q1001

Q1002

Q1003

Q1004

Q101

Q101

Q102

Q102

Q103

0IPRPML001A

0IMCRRH001A

0IMCRFA010A

0IPMG00027A

0IMCRRH001A

0IMCRRH001A

0IMCRRH001A

0IPRPML001A

0IPMG00027A

0IPMGKE030A

0IPMG00027A

0IPRPML001A

0IPRPS5005A

0IMMRAL014B

0IPMGON013B

0ISO206900A

0ISA721700C

0IMCRMN028B

0ILNR00015A

0IMCRTI028C

0ISS455880A

0IPH741400E

0IMMRAL014B

0IPH741400E

0IPRP00009A

0IMCR02006A

0IMMRAL025A

0IMMR00004A

0IMCR02005A

0IMP242560A

0IMMR00002A

0IMMR00002A

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR102008AA

0TR387500AA

0TR387500AA

IC

TRANSISTOR

- 28 -

DIODE

- 29 -


D1201

D300

D500

D501

D502

D504

D505

D506

ZD100

ZD101

ZD107

ZD300

ZD301

ZD400

ZD600

C1000

C1005

C1007

C1009

C1010

C1019

C1022

C103

C1030

C1043

C1046

C1047

C1050

C1051

C1064

C1065

C1066

C1067

C1068

C1069

C1071

C1073

C108

C1082

C1083

C1084

C1085

C1087

C1098

C1099

C1102

C1105

C1107

C1108

C1110

0DS113379BA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DZRM00248A

0DR050008AA

0CE477SF6DC

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

0CE4763F618

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE477SF6DC

0CE477SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE477SF6DC

0CE227SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE477SF6DC

1SS133 T-72 TP ROHM KOREA DO34 90V

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

SD05.TC R/TP SEMTECH SOD323 5V 5A 15A








RLZ8.2B-TE11 ROHM R/TP LLDS(LL-34)


470UF MVG 16V 20% R/TP(SMD) SMD


100UF MVG 16V 20% SMD R/TP





47UF SRE 16V M FL TP5





























C1115

C1116

C1117

C1118

C1119

C1120

C1126

C1135

C1136

C1137

C1138

C1148

C1149

C1150

C1151

C1154

C1159

C1162

C1165

C1166

C117

C118

C1185

C1186

C1187

C1188

C1189

C119

C1190

C1191

C1192

C1193

C1195

C1199

C120

C1200

C1201

C121

C1225

C1230

C1231

C1245

C1247

C129

C130

C1302

C1304

C1306

C1309

C131

C1311

C1312

0CE477DJ618

0CE477SF6DC

0CE227VF6DC

0CE477SF6DC

0CE477DJ618

0CE227VF6DC

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE227SF6DC

0CE106SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CK105DF64A

0CK105DF64A

0CE106SF6DC

0CE476SF6DC

0CE227SF6DC

0CE227SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

470UF STD 35V 20% FL TP 5


220UF MV 16V 20% R/TP(SMD) SMD


470UF STD 35V 20% FL TP 5

220UF MV 16V 20% R/TP(SMD) SMD


































1UF 2012 16V 20% R/TP F(Y5V)

1UF 2012 16V 20% R/TP F(Y5V)












CAPACITOR

For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;

CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic

RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible

- 30 -


C1313

C1314

C1315

C1316

C1317

C1318

C135

C1414

C1415

C1419

C1420

C1424

C1425

C1428

C1438

C1441

C1506

C203

C204

C208

C210

C211

C214

C215

C221

C238

C241

C300

C304

C305

C307

C310

C315

C318

C319

C320

C321

C325

C328

C330

C338

C340

C342

C347

C402

C403

C413

C418

C425

C444

C451

C456

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE475SK6DC

0CE475SK6DC

0CE106SF6DC

0CK105DF64A

0CE106SF6DC

0CE106SH6DC

0CE106SH6DC

0CE106SH6DC

0CE106SH6DC

0CE476SF6DC

0CE475SK6DC

0CE477SF6DC

0CE477SF6DC

0CE475SK6DC

0CE477SF6DC

0CE106SF6DC

0CE475SK6DC

0CE477SF6DC

0CE107SF6DC

0CE476SK6D8

0CE107SF6DC

0CE226SF6DC

0CE107SF6DC

0CE476SF6DC

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CE476SF6DC

0CE105SK6DC

0CE105SK6DC

0CE476SF6DC

0CE226SF6DC

0CE335VK6DC

0CE107SF6DC

0CE226SF6DC

0CE107SF6DC

0CK105DF64A

0CK105DF64A








4.7UF MVG 50V 20% SMD R/TP



1UF 2012 16V 20% R/TP F(Y5V)
















47UF MVG,MC 50V 20% SMD TAPPING





2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP






3.3UF MV 50V 20% R/TP(SMD) SMD




1UF 2012 16V 20% R/TP F(Y5V)

1UF 2012 16V 20% R/TP F(Y5V)


C457

C462

C463

C464

C465

C480

C481

C482

C483

C484

C495

C527

C610

C728

C729

C730

C731

C735

C737

C739

C745

C750

C752

C760

C762

C764

C767

C771

C832

C833

C834

C835

C836

C837

C838

C839

C840

C851

C853

C884

C896

C901

C904

C905

C930

C950

L1000

L1101

L1102

L1103

0CE335VK6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SK6DC

0CE108DJ618

0CE475SK6DC

0CE475SK6DC

0CF4741L438

0CF4741L438

0CE108DJ618

0CE476SF6DC

0CE107SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

3.3UF MV 50V 20% R/TP(SMD) SMD





1000UF STD 35V 20% FL TP 5



0.47UF D 63V 5% TP 5 M/PE NI

0.47UF D 63V 5% TP 5 M/PE NI

1000UF STD 35V 20% FL TP 5




































26UH 1UEWPHY 22.5TURN YL-9N 0.4







COIL

- 31 -


L1104

L404

L405

L406

L407

AR1200

AR1201

AR1202

AR1203

AR1204

AR1205

AR700

AR701

AR702

AR703

AR704

AR705

AR806

AR807

AR808

AR809

AR810

AR811

AR812

AR813

AR814

AR815

AR816

AR817

R230

D1003

D1103

LD101

SW101

SW102

SW103

SW104

SW105

SW106

SW107

SW108

SW700

SW800

L100

6140VB0004B

6140VB0032A

6140VB0032A

6140VB0032A

6140VB0032A

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RD0331H609

0DL233309AC

0DL233309AC

0DL200000CA

140-315A

140-315A

140-315A

140-315A

140-315A

140-315A

140-315A

140-315A

6600VR1004A

6600VR1004A

6200J000013


DBF-1015A 15.5UH 10PIE DIGITAL AUDIO




22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

MNR14-E0A-J-510 R OHM 51 OHM 5%












3.3 OHM 1/2 W 5.00% TA52

SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD

SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD

SAM5670(DL-2LRG) BK Y-GREEN -

TACT SKHV17910B LG C&D 12V








SKHMPW 5P CHIP TACT J-ALPS

SKHMPW 5P CHIP TACT J-ALPS

MLB-321611-0500P-N2 MAG LAYERS


L1004

L1005

L1006

L1007

L1008

L1009

L101

L1010

L1011

L1012

L1013

L1014

L1015

L1016

L1017

L1018

L1019

L1020

L1021

L1022

L1023

L1024

L1025

L110

L1105

L1106

L1107

L1108

L1109

L111

L1110

L1111

L1112

L1113

L1115

L1116

L1117

L1118

L1119

L1120

L1121

L1122

L1123

L1125

L1126

L1127

L1128

L1129

L1130

L114

L115

L119

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200JB8010L

6200JB8010L


















































MLB-201209-1000L-N2 MAG LAYERS






SWITCH

FILTER & CRYSTAL

LED

RESISTOR

- 32 -


L120

L1204

L1205

L1206

L1207

L1208

L1209

L121

L122

L123

L124

L125

L126

L200

L201

L202

L203

L204

L300

L301

L302

L400

L401

L402

L403

L408

L409

L410

L500

L502

L503

L506

L604

X1200

X300

X400

X700

X800

JK100

JK101

JK101

JK102

JK103

JK104

JK1200

JK400

JK502

JK600

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6210VC0005A

6210VC0005A

6210VC0005A

6210VC0005A

6210VC0005A

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200JB8010L

6200J000013

6200J000013

6212AB2845A

166-E02F

156-A02M

6212AB2844A

6212AB2844A

6612J00043C

6612J00043C

6613V00026A

6612J00043C

6612J10012A

6612J00038B

6612B00015B

6612J00037A

6612F00087A

6612F00087A









BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP





















RESONATOR,CRYSTAL ABLS-27.000MHZ

RESONATOR,CERAMIC CSBLA500KECZF09

RESONATOR,CRYSTAL HC49U 18.432MHZ



UPJ-R1-031 UGCOM S/T


UJB-03-28A UGCOM 6613V00004S


UJB-05-02C GR/BL/RD/WH/RD 1*5 SHIELD

UJB-03-25B UGCOM 6612J00038A

DC1R019WDH JAE 0.5MM,19PIN+2PIN,HDMI

UJB-02-12A UGCOM 2P RCA

UEJ-CV-032 UGCOM EAR JACK

UEJ-CV-032 UGCOM EAR JACK


A1

A2

A3

C1

C2

C3

JK500

JK601

PA101

TU200

TU201

3828VA0545F

6710V00126R

6410VEH003C

6850VA0004J

6851V00022C

6850J00005B

6630G70016A

6630G70017A

6712000002B

6700MF0010B

6700MF0010A

MANUAL,OWNERS MF056A EU/42PX3RV

REMOTE CONTROLLER, RF043A PIP

POWER CORD, M2511A-001 2800MM

CABLE,COAXIAL UL1365#26 150MM UCA-EX-069

CABLE,COAXIAL UL1365#26 VW-1,SOLDERLESS

CABLE,DVI LVDS UL20276 AWG30 500MM

CONNECTOR, A03-7071-094 SPG

CONNECTOR, A02-0915-101 SPG

REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1

TUNER, TAFM-W502P MINI 4SYSTEM SUB

TUNER, TAUM-W501P MINI 4 SYSTEM MAIN

ACCESSORIES

MISCELLANEOUS

JACK

PRINTED CIRCUIT BOARD

MAIN (TOP) MAIN (BOTTOM )

SIDE A/V(BOTTOM)

CONTROL

Apr., 2005Printed in KoreaP/NO : 3828VD0209Q

service manuall lg-tv 42px3rv

Documents