setup instructions...2. slide tool-less connectors across seam of extrusions. * 3. tighten all knobs...

© 2020

Locked layer containsplaceholder marks.

Perspective View

Plan View

10’

10’

Symphony SYK-1019 - 10’ x 10’ Portable Display

If you would like to tell us about your experience with your setup instructions please email us at [email protected] INSTRUCTIONS

© 2020


= 1 sq ft

Plan View

© 2020

General Setup Instructions- Read entire setup instruction manual prior to unpacking parts and pieces.

- The setup instructions are created specifically for this configuration.

- Setup instructions are laid out sequentially in steps, including exploded views with detailed explanation for assembly.

Cleaning & Packing- For Cleaning Metal, Plex, & Laminate Parts: Use a MILD NON-ABRASIVE cleanser and soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat and prolonged sun exposure. Heat and UV exposure will warp and fade components.

- Retain all provided Packing Materials. All provided packing materials are for ease of repacking & component protection.

Disassembly- For loss prevention, keep allknobs & connectors attached toextrusions during disassembly.

Part Identification - Numbering

7A

Engaged Lock

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUSTBE TIGHTLY SECURED

WARNING

General Information

© 2020

TSP49 Profile

All knobs must be tightened securely to ensure a proper connection.

Adjust connectors if necessary toprevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

CornerConnector

CornerConnector

CornerConnector

CornerConnector

COMPLETED ASSEMBLY

Slide verticals overlower connectors.

Then slide upperconnectors intogroove of verticals.

Tighten all knobs.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of corner connectors on lower and upper horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal extrusion into grooves of vertical extrusions.

Disassembly1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during packing & shipping.

Keep straight connectors in groove ofextrusion. Do not remove connectorsduring disassembly.

Straight Connection

3) Tighten all knobs to secure connection.

When assembling frame, first attach all straightconnectors, then attach corner connectors.

1) Place extrusions end-to-end.

Slide connector across seam of extrusions.Tighten all knobs.

All knobs must be tightened securely to ensure a proper connection.

Straight Connector

2) Loosen all knobs, then slide straight connector across the seam of extrusions.

Tool-less Frame Assembly

© 2020

Step 1 of 5


***

*

*

*

**

*

* **

When assembled

Item12345678910111213

Qty.1111111111112

Steps:

Refer to the Tool-less Frame Assembly general information page.

1) Assemble vertical extrusions [1-2], [3-4], [11-12] & horizontals [5-6-7], [8-9-10] together, using Tool-less Spline Connectors.2) Connect vertical assemblies [1/2], [3/4] between horizontal assemblies [5/6/7], [8/9/10], using Tool-less Corner Connectors.3) Install Base Plates [13] to bottom corners of frame assembly as shown. See Base Plate Attachment detail.4) Lift frame to upright position, then connect vertical assembly [11/12] between horizontal assemblies [5/6/7], [8/9/10] using Connection Lock w/ Knob.

Description45”h TSP49 Vertical Extrusion41”h TSP49 Vertical Extrusion45”h TSP49 Vertical Extrusion41”h TSP49 Vertical Extrusion36.166”w TSP49 curved Horizontal Extrusion36.166”w TSP49 curved Horizontal Extrusion36.166”w TSP49 curved Horizontal Extrusion36.166”w TSP49 curved Horizontal Extrusion36.166”w TSP49 curved Horizontal Extrusion36.166”w TSP49 curved Horizontal Extrusion41.209”h Z45 Vertical Extrusion41.209”h Z45 Vertical Extrusion6” x 22” Base Plate w/ flange

**

1

2

3

4

8

10

12

11

9

13

13

56

Connection Lockw/ Knob*

BACK VIEW

Knobs face back of assembly.

Tool-less Spline Connector1. Place extrusions end-to-end.

2. Slide tool-less connectors across seam of extrusions.

*

3. Tighten all knobs to secure connection.

Tool-less Corner Connector1. Slide extrusion onto Corner Connector.

2. Tighten all knobs to secure connection.

*

Keep corner connectors attached to horizontal extrusions.

Assemble frame flat on ground.

7

*

1) Place key hole over bolt on panel & slide down.2) Twist knob to secure connection.

Base Plate Attachment*

bolt

knobBase Plate

threadedhole

key hole

FRONT VIEW

Curvedtool-less

connectorCurvedtool-less

connector

Curvedtool-less

connectorCurvedtool-less

connector

Backwall Frame Assembly

© 2020

Step 2 of 5


Steps:1) Apply SEG Graphic to front of assembled frame.SEG Graphic Installation

Corner A

Corner D

Corner B

Corner C

It is important to first insertgraphic into each alternatecorner, then to the sides ofthe frame. If this is not done,graphic will not fit into theframe correctly.

Step 1Insert corner A. Turn edge ofgraphic so silicon welt isperpendicular to face ofgraphic. Insert narrow sideof welt with fabric to outsideinto the channel. Repeat forother side of this corner.

Step 2Repeat Step 1 for oppositecorner C, then insert cornerB, followed by corner D, tocomplete the installation ofthe corners.

Graphic RemovalTo remove the graphic fromthe frame, locate the fabricpull tab. Gently pull up onthe tab to remove the fabric.

Step 3Once all corners are inserted,press one silicon edge intochannel from corners andwork toward the center.Make sure welt is fully insertedinto channel. Continue untilall sides are done. Smoothout edges of graphic.

When assembled

FRONT VIEW

SEG Graphic

Fabric Graphics Application

© 2020

Step 3 of 5


WorkstationWorkstation

LightLight

* *

Steps:1) Attach Workstation Mounting Brackets to backwall verticals as shown. See Workstation Bracket Attachment detail.2) Assemble Workstation legs & counter tops to brackets. See Workstation Assembly detail.3) Affix Graphics to front of workstation assemblies, using Velcro.4) Attach Lights to top of backwall as shown. See Light Attachment detail.

Attach clamp of stem lightto top of horizontal extrusionwhere desired.

Twist knob on back totighten in place.

Light Attachment*

knob

Light

BACK VIEW

Extrusion

Hook the Mounting Bracketover the vertical extrusion.

SlideBracketforward

Slide down ontoV4 connector

Tighten knobsto secure.

MountingBracket

Workstation Bracket Attachment

Slide bracket forward, thendown onto V4 connector.

Tighten thumb screws tosecure connection to insideof frame.

Bracket

TOP VIEW SIDE VIEW

1 2 3

V4

V4 connectors stay permanentlyattached to vertical extrusion.

*

ThreadedStuds

Wingnuts

Counter Top

MountingBracket

CounterLegs

UNDERSIDE VIEW

3) Attach power cords to wireless chargers.

2) Connect Counter Top to Mounting Bracket, using wing nuts.

1) Attach threaded studs on underside of Counter Top to Counter Legs; secure with wing nuts.

Workstation Assembly

Keep cords attached tounderside of counter top.

Underside View of CounterTo Power

USBcharging

pad

powercordscharging

block

Counter Top

*

When assembled

Graphic

*

Graphic

Backwall Attachments

© 2020

Step 4 of 5


Completed Assembly

Steps:1) Connect Floating Graphics to backwall using brackets. See Floating Graphic Attachment detail.

Floating Graphic Attachment

Hook the Graphic Bracketonto the extrusion & snapinto place.

Affix graphic to Bracketusing Velcro.

Brackets may be attached tohorizontal or vertical extrusion.

Two (2) brackets are required per graphic.

12

Graphic Bracket

Velcro

TOP VIEW

Extrusion

Hook Bracketover

vertical

Snap intoplace

Velcro

Velcro

Velcro

Bracket

Bracket

*

Graphic

** *

*FloatingGraphic

FloatingGraphic

Backwall Attachments (cont’d)

© 2020

Step 5 of 5


Pedestal Base Assembly Pedestal Top Attachment

ScrewCap

ScrewCap

Side Panel

Shelf

Shel

f Sup

port

Shel

f Sup

port

Shel

f Sup

port

Shel

f Sup

port

Floor

Side Panel

Counter Top

Front Panel

Back Panel(with Door)

NOTE: Remove pins for floor from side panels when packing.

1 2

Counter Top Attachment*

Align hole with pin. Rotate pin. Springwill push pin into hole.

* *

When assembled

Steps:1) Attach pins at bottom interior of side panels. Note: Pins are designed to be slightly angled.2) Use screw caps to secure side panels to front & back panels.3) Slide floor into the bottom of assembled pedestal base. The floor will sit on pins of the side panels.4) Connect shelf supports with Velcro inside of panels, then place shelf on top of supports.5) Attach Counter Top to assembled pedestal base. See Counter Top Attachment detail.

SYM-408 Counter Assembly

setup instructions...2. slide tool-less connectors across seam of extrusions. * 3. tighten all knobs...

Documents