Sezionatori di linea Sezionatori di linea ed anelli di dred anelli di drenaggioenaggioSpectacle flanges and drip rings

INDICE INDEX

DRIP RINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . pag. 111CLASS 150. . . . . . . . . . . . . . . . . . . . . . . . . . . . . “ 112CLASS 300. . . . . . . . . . . . . . . . . . . . . . . . . . . . . “ 113CLASS 600. . . . . . . . . . . . . . . . . . . . . . . . . . . . . “ 114CLASS 900. . . . . . . . . . . . . . . . . . . . . . . . . . . . . “ 115CLASS 1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . “ 116CLASS 2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . “ 117CLASS 150 MALE-FEMALE RING TYPE . . . . . . . . 118-119CLASS 300 MALE-FEMALE RING TYPE . . . . . . . . 120-121CLASS 600 MALE-FEMALE RING TYPE . . . . . . . . 122-123CLASS 900 MALE-FEMALE RING TYPE . . . . . . . . 124-125CLASS 1500 MALE-FEMALE RING TYPE . . . . . . . 126-127CLASS 2500 MALE-FEMALE RING TYPE . . . . . . . 128-129

SEZIONASEZIONATORI DI LINEA TORI DI LINEA ED ANELLI DI DRENAGGIOED ANELLI DI DRENAGGIOSPECTACLE FLANGES AND DRIP RINGS

111

ANELLI DI DRENAGGIODRIP RINGS

CLASSECLASS150

SELEZIONATORI DI LINEAPER FLANGE CON FACCIA A SEMPLICE RISALTO SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RAISED FACE FLANGES

112

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Optional raised face may be specified by the purchaser.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS300

SELEZIONATORI DI LINEAPER FLANGE CON FACCIA A SEMPLICE RISALTO SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RAISED FACE FLANGES

113

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Optional raised face may be specified by the purchaser.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS600

SEZIONATORI DI LINEAPER FLANGE CON FACCIA A SEMPLICE RISALTO O PIANESPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RAISED FACE OF FLAT FACE FLANGES

114

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Optional raised face may be specified by the purchaser.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

115

CLASSECLASS900

SEZIONATORI DI LINEAPER FLANGE CON FACCIA A SEMPLICE RISALTO O PIANESPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RAISED FACE OF FLAT FACE FLANGES

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Optional raised face may be specified by the purchaser.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS1500

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

116

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Optional raised face may be specified by the purchaser.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

117

CLASSECLASS2500

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Optional raised face may be specified by the purchaser.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS150

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

118

TIPO MASCHIO MALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Oval or octagonal ring shapes may be provided; only the oval ring is illustrated for simplicity. Ring dimensions shall be in

accordance with ASME B16.20 except Th = T + t where T is the ring height specified in ASME B16.20.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS150

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

119

TIPO FEMMINA FEMALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Female ring-joint groove dimensions shall be in accordance with ASME B16.5.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS300

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

120

TIPO MASCHIO MALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Oval or octagonal ring shapes may be provided; only the oval ring is illustrated for simplicity. Ring dimensions shall be in

accordance with ASME B16.20 except Th = T + t where T is the ring height specified in ASME B16.20.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS300

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

121

TIPO FEMMINA FEMALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Female ring-joint groove dimensions shall be in accordance with ASME B16.5.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS600

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

122

TIPO MASCHIO MALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Oval or octagonal ring shapes may be provided; only the oval ring is illustrated for simplicity. Ring dimensions shall be in

accordance with ASME B16.20 except Th = T + t where T is the ring height specified in ASME B16.20.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS600

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

123

TIPO FEMMINA FEMALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Female ring-joint groove dimensions shall be in accordance with ASME B16.5.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS900

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

124

TIPO MASCHIO MALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Oval or octagonal ring shapes may be provided; only the oval ring is illustrated for simplicity. Ring dimensions shall be in

accordance with ASME B16.20 except Th = T + t where T is the ring height specified in ASME B16.20.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS900

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

125

TIPO FEMMINA FEMALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Female ring-joint groove dimensions shall be in accordance with ASME B16.5.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS1500

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

126

TIPO MASCHIO MALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Oval or octagonal ring shapes may be provided; only the oval ring is illustrated for simplicity. Ring dimensions shall be in

accordance with ASME B16.20 except Th = T + t where T is the ring height specified in ASME B16.20.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS1500

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

127

TIPO FEMMINA FEMALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Female ring-joint groove dimensions shall be in accordance with ASME B16.5.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS2500

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

128

TIPO MASCHIO MALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Oval or octagonal ring shapes may be provided; only the oval ring is illustrated for simplicity. Ring dimensions shall be in

accordance with ASME B16.20 except Th = T + t where T is the ring height specified in ASME B16.20.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.

CLASSECLASS2500

SELEZIONATORI DI LINEAPER FLANGE CON GIUNTO AD ANELLO METALLICO (R.T.J.)SPECTACLE FLANGES - SINGLES BLINDS - RING SPACERFOR RING JOINT TYPE FLANGES

129

TIPO FEMMINA FEMALE RING TYPE

GENERAL NOTE: dimensions are in millimeters.

NOTES:1. Hole size (where required due to bolt spacing) shall be the same as the flange bolt hole and located such that it will not

interfere with bolting between two flanges.2. Female ring-joint groove dimensions shall be in accordance with ASME B16.5.3. The thickness of the web (or tie bar) dimension Wt, shall be 0.25 inch (6,4 millimeter) minimum, except when t is less

than 0.25 inch, Wt shall equal t.