“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved. 9069158 BA Revised 06/03/13

Side Jamb Liner Replacementfor E-Series Double-Hung

Thank you for choosing Andersen.

For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com

Please leave this guide with building owner.

▶ Read guide from beginning to end before starting maintenance procedure. Read all warnings and cautions during unit maintenance.

Parts Included (1) Side Jamb Liner

▶ For information, calculating, and design pressure ratings for E-Series windows and doors go to www.eaglewindow.com/Wintelligence/Design-Pressure-Estimator.aspx

▶ Check with your local building code official to identify and confirm compliance with local building code requirements.

Tools Needed ∙ Safety Glasses ∙ Flat Blade Screw Driver ∙ Finish Nailer (for monumental units only) ∙ Pliers (for monumental units only) ∙ Putty Knife (for monumental units only)

Supplies Needed ∙ Denatured Alcohol ∙ Clean Cloth

Side Jamb Liner

Use caution when working at elevated heights and around unit openings. Follow manufacturers’ instructions for ladders and/or scaffolding. Failure to do so may result in injury or death.

Follow manufacturers’ instructions for hand or power tools. Always wear safety glasses. Failure to do so may result in injury and/or product damage.

Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry and install window and door products to avoid injury and/or product damage.

29069158

Slide tilt latches inward while tilting sash in 90 degrees.

Tilt Latches

Tilt Latch

Lower top sash 6”.

6 Inches

6Interior

7Interior

Pivot bottom sash to remove from window frame as shown. Place sash on clean flat work surface, exterior side up.

Rotate and hold lock handles toward center while tilting sash in 90 degrees.

Unlock window and raise bottom sash 4".

Lock Handles

4 Inches

Lock Handles

2Interior

3Interior

4Interior

Bottom Sash

Bottom Sash

Pry interior side stop away from frame. Repeat on opposite side. Remove any nails from frame and interior side stops.

Remove sash stop from the side jamb.

For Monumental Only

Single Hung and Monumental Only

▶ For double hung units proceed to step 6.

1Interior

▶ For single and double hung units proceed to step 2.

5Interior

Pliers

Interior Side Stop

Pivot top sash to remove from window frame as shown. Place sash on clean flat work surface, exterior side up.

8Interior

Top Sash

Putty Knife

Interior Side Stop

39069158

Slide outside side jamb liner insert up 12”.

12 Inches

Pocket Cover

Grasp jamb liner pocket cover at bottom and pull outward and down from behind head stop to remove and save for reuse.

9Interior

12Interior

Outside Jamb LinerInsert

Insert flat blade screwdriver into cam slot, apply firm downward pressure, and rotate 1/4 turn. Hold firmly allowing shoe to rise until it stops. Repeat for other three balances.

BalanceShoe

ShoeBalanceCam

Flat BladeScrewdriver

Balance shoes are under high tension. Use flat blade screwdriver with long handle so that both hands can be used to release balance tension. Suddenly releasing balance shoe could damage window unit. Cam in unlocked

(travel) position2nd

1st

Cam in locked position

Remove existing sill cushion and save for reuse.

Sill Cushion

Flat BladeScrewdriver

11Interior

10Interior

49069158

Remove side jamb liner working from bottom to top, prying jamb liner edge from frame to disengage as shown.

Jamb Liner

Jamb Liner

13Interior

Pull side jamb liner down slowly, while supporting head stop and remove from frame. Dispose of side jamb liner properly.

14Interior

Insert new side jamb liner behind head stop.

15Interior

Position side jamb liner in frame, locking front lip behind interior side stop.

16Interior

Jamb Liner

InteriorSideStop

Jamb Liner

Re-engage side jamb liner, working from bottom to top, pressing jamb liner edge into frame to engage as shown.

17Interior Balance

Shoe

ShoeBalanceCam

Flat BladeScrewdriver

Unlocked Position

Locked Position

Insert flat blade screwdriver into cam and pull down until shoe is aligned with shoe on opposite side. Rotate cam 1/4 turn to lock.

18Interior

Side Jamb Liner

Head Stop

59069158

Slide outside side jamb liner insert down to sill.

19Interior

Jamb LinerExterior Insert

Clean area with a clean cloth and denatured alcohol.

Clean Cloth and Denatured Alcohol

20Interior

CheckrailWeatherstrip

Side CuttingPliers

Position wide end of sill cushion in jamb liner channel, adhesive side down, and press into place.

Sill Cushion

21Interior

Rotate top sash to engage pivot pins into balance shoes of exterior channel. Push down until both pivot pins are fully engaged.

Balance Shoes

Pivot Pin

22Interior

Tilt Latches

Tilt Latches

23Interior

Tilt sash up, retracting tilt latches by sliding inward. Release tilt latches to re-engage sash in frame. Verify top sash operation. Repeat steps 22-23 if sash does not operate correctly.

Insert top of jamb liner pocket cover, beveled side toward exterior, into interior channel, sliding it up behind head stop. Press jamb liner pocket cover firmly into place, starting at top, zippering down full length.

Jamb Liner Pocket Cover

InteriorChannel

Beveled Side24Interior

Jamb Liner Channel

Head Stop

Wide End

Sill Cushion

▶ For double hung units proceed to step 26.

69069158

Rotate bottom sash to engage pivot pins into balance shoes of interior channel. Push down until both pivot pins are fully engaged.

Balance Shoe

InteriorChannel

Pivot Pin

26Interior

Tilt sash up, retracting tilt latches by rotating lock handles toward center, then release lock handles to re-engage sash.

Lock Handles

27Interior

Verify sash operation. Repeat steps 26-27 if sash does not operate correctly.

Lock Handles

28Interior

Close and lock sash.

Lock Handles

30Interior

Verify sash operation. Repeat steps 30-31 if sash does not operate correctly.

Lock Handles

29Interior

▶ Side jamb liner replacement procedure is complete for monumental units.

Reapply interior side stop on frame. Repeat on opposite side. Fasten with finish nailer.

Interior Side Stop

For Monumental Only

31Interior

▶ Side jamb liner replacement procedure is complete for single and double hung units.

▶ For monumental units proceed to step 31.

Replace sash stop in the side jamb.

25Interior

Sash Stop

Single Hung and Monumental Only