simulation of flow
DESCRIPTION
pls don't readTRANSCRIPT
![Page 1: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/1.jpg)
SIMULATION OF FLOW BOILING HEAT TRANSFER IN A
SINGLE HORIZONTAL MICROCHANNEL
![Page 2: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/2.jpg)
• In this study both the single phase and multiphase models are used for solving the
Problems.
![Page 3: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/3.jpg)
At first the single phase model is used to obtain fully developed velocity profile at outlet of the pipe and then this velocity profile is used as the inlet profile of multiphase pipe flow simulation
![Page 4: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/4.jpg)
WHY???
![Page 5: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/5.jpg)
• THIS IS AN TECHNIQUE TO REDUCE COMPUTATIONAL BURDEN.
![Page 6: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/6.jpg)
FOR SINGLE PHASE FLOW1)Continuity eqn2)Momentum eqn3)Energy eqn
To calculate velocity
To calculate turbulent energy and energy dissipation rate
![Page 7: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/7.jpg)
TWO PHASE MODELING EQUATIONS there are two approaches for the numerical calculation of multiphase flows: 1)Euler-Lagrange approach. 2)Euler-Euler approach.
![Page 8: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/8.jpg)
Euler-Lagrange approachThe fluid phase is treated as a continuum by solving the Navier Stokes equation.
Dispersed phase is solved by tracking a large number of particles, bubbles, or droplets through the calculated flowfield.
![Page 9: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/9.jpg)
Euler-Euler approach In the Euler-Euler approach, the different phases are treated mathematically as interpenetrating continua.
![Page 10: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/10.jpg)
Three different Euler-Euler multiphase models are available: • Volume of fluid (VOF) model • Mixture model • Eulerian model.
![Page 11: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/11.jpg)
VOF
It is used for two or more immiscible fluids where the position of the interface between the fluids is of interest.
![Page 12: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/12.jpg)
MIXTURE MODELThe mixture model is designed for two or more phases (fluid or particulate).The mixture model solves for the mixture momentum equation .
This is applicable for liquid-solid flows.
![Page 13: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/13.jpg)
EULERIAN MODEL
The phases can be liquids, gases, or solids in nearly any combination.
Eulerian multiphase model, the number of secondary phases is limited only by memory requirements and convergence behavior.
![Page 14: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/14.jpg)
A single pressure is shared by all phases.
Momentum and continuity equations are solved for each phase.
![Page 15: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/15.jpg)
![Page 16: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/16.jpg)
In ANSYS Workbench a rectangular cross-sectional micro channel of equivalent hydraulic diameter is drawn and is represented as a 2-D computational domain. The geometry consists of inlet, outlet, wall (upper wall) & heated wall (uniform heat flux is given to this wall)
![Page 17: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/17.jpg)
WHY 2-D
In 3-D we need more mesh ,that means more calculation, so for a particular caser if we can represent our 3-D model into 2-D it will save a lot of time.
![Page 18: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/18.jpg)
![Page 19: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/19.jpg)
![Page 20: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/20.jpg)
![Page 21: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/21.jpg)
MESHING OF THE COMPUTATIONAL DOMAIN In meshing the geometry is divided into small small computational domain.
![Page 22: Simulation of Flow](https://reader034.vdocuments.net/reader034/viewer/2022042821/563db8e0550346aa9a97cbe1/html5/thumbnails/22.jpg)