MAIN PARTS

1.Face Plate2.Reverse Stitch Button3.Slow Button4.Start/Stop Button5.Speed Control Lever

6.Extension Table (Accessory Case)7.Bobbin Winder Tension disc8.Needle Up/Down Button

9.Thread Tension Regulator10.Spool pin11.Bobbin winder Shaft12.Bobbin Winder Stop13.Hand Wheel14.Stitch Width Button15.Stitch Length Button16.Pattern Selector Button17.Thread Cutter

1

3

17

4

5

2

6

7 8 9 10 11 12 13

-2-

58

47

5756

4645

59 60

48 49

1615141312

36

25

3534

2423

37 38

26 27

030201 04 05

63

52

61 62

50 51

64 65

53 54

66

55

2120191817

41

30

39 40

28 29

42 43

31 32

0806 07 09 10

22

44

33

11

14

15

16

-3-

20

21

23

22

18

19

32

26

31

27

28

29

3035

34

38

37

36

25

24

39

18.Carrying Handle19.Thread guide for upper threading20.Power switch21.Air vent22.Foot control plug23.Plug socket24.Power cord25.Foot control26.Lower thread guide27.Needle threader lever28.Needle threader29.Buttonhole lever30.Presser foot thumb screw31.Needle plate32.Bobbin cover

34.Presser foot holder35.Presser foot36.Needle thread guide37.Needle clamp screw38.Presser foot lever39.Drop feed lever

33

33.Bobbin cover release lever

40

40.LED light

ACCESSORIES

-4-

1.Needle set2.Bobbins3.Spool pin cap (large)4.Spool pin cap (small)5.Straight stitch foot6.Needle plate screwdriver7.Screwdriver 8.Buttonhole opener with brush9.Oiler

10.Buttonhole Foot11.Overcasting Foot12.Zipper Foot

12 3

4

OPENING THE ACCESSORY CASE

To open the accessory case, lift up on thetop left side of the table and pull toward you.

11 12

8

9

10

Some accessories are provided in the accessory case.

5

7

6

13

13.Blind hem Foot

14

14.Satin Foot

15 1617

15.Rolled hem Foot16.Gathering Foot17.Darning & Embroidery Foot18.General purpose foot(on machine)19.Extension table

18 19

-5-

a.REMOVING THE EXTENSION TABLEHook your finger to the bottom of extensiontable and slid to the left. To attach, insert tothe right.

b.OPENING THE ACCESSORY CASE

Hook your finger to the left side of accessorycase and pull toward you.

DUST COVER

Cover the machine with dust cover when it isnot in use.

This manual will be stored on the holderprovided on the side of the cover.

-6-

CHANGING THE PRESSER FOOT

The presser foot must be changed according to the stitch you sew, or work you do.

CAUTION:To prevent accidents.

Turn off the power switch before you change the presser foot.

1.Turn the hand wheel toward you until the needle is at its highest point.2.Raise the presser foot lifter.3.Remove the presser foot by pushing the presser foot release lever toward you.4.Place desired foot with its pin directly under the slot in presser foot holder.5.Lower the presser foot lifter and the presser foot will snap into place.

REMOVING THE PRESSER FOOT HOLDER

INSERTING THE NEEDLE

Select a needle of the right type and size for the fabric to be sewn.

CAUTION:To prevent accidents.

Turn off the power before removing the needle.

1.Turn the hand wheel toward you until the needle is at its highest point.2.Loosen the needle clamp screw.3.Remove the needle.4.Insert new needle into needle clamp with the flat side to the back and push it up as far as it will go.5.Tighten the needle clamp screw.

A.Do not use bent or blunt needles. Place needle on a flat surface and check to see if bent.

5

A

3

4

1

5

A

3

2

1!

!

4

You may need to remove the presser foot holder to use some presser feet.To remove, raise the presser foot lifter and loosen the presser foot thumb screw (A).To attach, tighten the screw after raising the presser foot holder.

2

-7-

CONNECTING THE MACHINE

1

2

-9-

FOOT CONTROLLER

A

C

B

For this machine use foot controller type YSD 180034.

-11-

BOBBIN WINDING

WINDING THE BOBBIN

spool of thread on the pin.

1.Pivot spool pin into highest horizontal spool pin position.

2.Pass a spool of thread on the spool pin. Secure to place a

3.Pass thread from spool through thread guides as shown.

4.Pull end of thread through hole in bobbin as shown.

5.Make sure the bobbin winder shaft is in left position. Place bobbin onto shaft with end

6.Start machine. The thread that is held will snap or may be trimmed with a scissors.

4 532

1

21REMOVING THE BOBBIN

1.Remove the slide cover by sliding the locker to right and push down the left corner of slide cover. At the same time.

2.Remove the bobbin from the machine.

Secure it with the spool cap to ensure smooth flow of thread.

of thread coming from top of bobbin. Push bobbin winder shaft to right until it

clicks. Hold onto end of thread.

Bobbin will cease turning when completely filled. Push shaft to left to removebobbin.

-12-

2

CB

3

4

A

1

INSERTING THE BOBBIN

1. Place bobbin into bobbin holder with the

thread unwinding counter clockwise.

2. Draw thread into notch (A).

3. Pull thread toward the left and along the

inside of spring (B) until it slips into notch

(C) being sure that thread does not slip out

of notch (A).

4. Pull thread out about 10 inches and replace

the slide cover.

CB

A