single lever c-spout bar faucet with 6 1/2” reach...consult your local rohl showroom for...

1

1 4

3 /

3 2

"

A3606/6.5LP (Porcelain Lever without Handspray)A3606/6.5LM (Metal Lever without Handspray)A3606/6.5LPWS (Porcelain Lever with Handspray)A3606/6.5LMWS (Metal Lever with Handspray)

FEATURES COLORS/FINISHES WARRANTY

www.rohlhome.com

• 6 1/2" reach spout• Ceramic disc single lever

cartridge • C- spout• 1 3/8" cutout• Swivel spout• 4” extension kit C7555EXT

• Polished Chrome• Polished Nickel• Satin Nickel• Tuscan Bronze• Inca Brass

Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.

• Limited Lifetime

ROHL Country Kitchen

Single Lever C-Spout Bar Faucet with 6 1/2” Reach

2

www.rohlhome.com


A3606/6.5 Spare Parts

Spout Ring SetC7593SET

A5556CR

C7676P

C7675M

A5556CR

3

www.rohlhome.com


A3606/6.5WS Spare Parts

C7005KIT (*)DIVERTER

spout ring setC7593SET

C7108N

-C3608/5KIT

-C7005MKIT

4


www.rohlhome.com

Installation Instructions

ART. A3606 / 6.5

4 5


www.rohlhome.com


ART. A3606 / 6.5 WS

6

www.rohlhome.com



6 7

www.rohlhome.com



INSTALLATION OF SINGLE HOLE FAUCET WITH SIDESPRAYMODELS INCLUDE:

DUAL LEVER MODELS: A1679WS, A1676WSSINGLE TOP LEVER MODELS: A3606WS, A3608, A3479

SINGLE LEVER SIDE LEVER MODELS: A3650WS

Model A3608WS shown

Install the supply hoses into the body- Note: hand tighten only, do not over tighten.

Install mounting stud securely or verify it is installed.

8

www.rohlhome.com



Insert faucet into mounting hole.

8 9

www.rohlhome.com



Under the sink, stack the half ring rubber gasket - 6, the half ringmouting plate - 7, then the mounting nut -9 onto the stud.

10

www.rohlhome.com



Check the position on the sink of the faucet, then tighten the nut with a 13mm wrench.

Note: the under deck mounting surface must be flat. If the mounting surface isirregular, the nut may not be secured, and the faucet will be loose on the sink.

10 11

www.rohlhome.com



• Insert the hand spray escutcheon into the sink holePlease note: make sure the hand spray hole is a minimum of 4 3/4” away from the

main body of the faucet.• Install the rubber washer -13, the flat metal washer -14, then the nut -15. Secure on the deck, butdo not over tighten.

4 3/4”

12

www.rohlhome.com



• Install the black hand spray hose to the supply from the faucet under the sink.- Guide the 9mm male end up through the escutcheon.- Install the hand spray with the required flat washer with screen on top of the sink.

• Connect the supply lines to the hot and cold supplies securely. - Please note: make sure the rubber washers with the screens are used. These screens

will prevent debris from entering the diverter.

•Turn on the water for the hot and cold.• Check the diverting action by operating the hand shower.

Please note: If there is a 99% divert or small trickle of water out the spout when using thehand spray that is acceptable. Due to water conditions, a 100% diverting action is notalways possible.• Check for leaks.

12 13

www.rohlhome.com



Please note: Only replace the cartridge if, the lever is stiff on to off, or from hot to cold.

Do not replace the cartridge if there is low flow or no flow. Low flow or no flow iscaused by obstruction or kinking of supply hoses.

If the hand spray is leaking, do not replace the diverter. Service or replace the handspray if there is a continous leak.

• Turn off the hot and cold supply lines to the faucet.

• Remove the handle and dome.- Remove the screw cover cap - 1

MAINTENANCEINSTRUCTIONS FOR REPLACEMENT OF THE C3009 CARTRIDGE

MODELS AFFECTED: A3608WS, A3606WS

14

www.rohlhome.com



• Tip the lever and dome up to access the 3mm allen key.- Loosen but do not remove the 3mm allen key- Note: use only a 3mm wrench. Not other size will work

• Remove lever and dome.

• Remove the ring nut cover-3

14 15

www.rohlhome.com



MAINTENANCE

Remove the cartridge nut with a smooth jawed wrench.

Remove the cartridge.

• Clean the cavity and remove all debris.• Liberally grease the cavity.• Install the cartridge as shown with the ports in the right alignment.• Install the nut

-Correct torque on the nut is 16 ± Newton (NM)-If no gauge is available

- Hand tighten the nut- Tighten a 1/4 turn or until snug- Do not over tighten

• With the dome and lever off, turn on the water and test for leaks• Then install the lever and dome and test the diverter by using the hand sprayPlease note: If there is a 99% divert or small trickle of water out the spout when using the hand

spray that is acceptable. Due to water conditions, a 100% diverting action is not always possible.

16

www.rohlhome.com



7 • Clean the cavity and remove all debris.• Liberally grease the cavity.• Grease the new diverter and install.• Install the cartridge as shown with the ports in the right alignment.• Install the nut

-Correct torque on the nut is 16 ± Newton (NM)-If no gauge is available

- Hand tighten the nut- Tighten a 1/4 turn or until snug- Do not over tighten

• With the dome and lever off, turn on the water and test for leaks• Then install the lever and dome and test the diverter by using the hand sprayPlease note: If there is a 99% divert or small trickle of water out the spout when using the hand

spray that is acceptable. Due to water conditions, a 100% diverting action is not always possible.

INSTRUCTIONS FOR REPLACEMENT OF THE C7005M DIVERTER

MODELS AFFECTED: A3608WS, A3606WS

C7005M(DIVERTER)

Please note: Only replace the diverter if no water is coming out the spout.

If the hand spray is leaking, do not replace the diverter. Service or replace the hand sprayif there is a continous leak.

1. Turn off the hot and cold supply lines to the faucetRemove the handle and dome

2. Remove the screw cover cap - 13. Tip the lever and dome up to access the 3mm allen key.Loosen but do not remove the 3mm allen key.Note: use only a 3mm wrench. No other size will workRemove lever and dome

4. Remove the ring nut cover - 35. Remove the cartridge nut with a smooth jawed wrench.6. Remove cartridgeRemove the diverter with a dental tool or needle nose pliers.• Please note: There are serveral types of diverters. Verify the diverter being removed is the same as the diverter being installed. They will be similar in appearance. Improper

installation will cause a malfuntion.

2 3 4

5 6 7

16 17

www.rohlhome.com



18

www.rohlhome.com



18 19

www.rohlhome.com



Spare Parts

THE O-RING MUST BE ALWAYS PALACEDBETWEEN THE HANDSPRAY AND HOSE VALVES

RING

20

www.rohlhome.com



Current kitchen faucets have a flow rate of 1.5 GPM from the aerator and the handspray.

If you are experiencing low flow from the spout: Do not change the cartridge

• Unscrew and clean the aerator 1 • Unscrew and clean the filters inside the supply connections. 3• Check the supply lines for kinks or obstructions. 3• Make sure the supply line stops are fully on. Not shown

If you faucet has a hand spray, and your hand spray has obstructed flow or no flow:

• Check the hand spray hose for kinks.5• Unscrew and clean the hand spray filter.4• Clean the aerator in the hand spray. 2

LOW FLOW OR NO FLOW TROUBLESHOOTING INSTRUCTIONS(ALL MODELS: A3608 shown)

5

4

20 21


www.rohlhome.com



single lever c-spout bar faucet with 6 1/2” reach...consult your local rohl showroom for...

Documents