skoda - ecs electronics | welcome following the installation of the electric kit, the fitting...

25
Part No: VW-190-07MU 1/25 This electric kit has to be installed by a professional workshop or a suitable qualified person. The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance! Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit! Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update). All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected. If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted. This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment! Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle’s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system. Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module. We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle’s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module from the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team! Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instruction must be observed! Electric wiring kit for towbars / 7-pin / 12N / 12 Volt / ISO 1724 Skoda Karoq Karoq Scout Karoq Sportline 11/2017 >> 02/2019 >> 02/2019 >> [email protected] www.ecs-electronicsuk.co.uk Revision: 3 / 06.08.2021 VW-190-07MU ECS Electronics UK 20 Speedwell Close Hun�ngton Chester, CH3 6DX Email-sales: [email protected] Email-technical: [email protected] SALE: +44 (0) 7590 564639 TECHNICAL: +44 (0) 7440 202052 WEB: www.ecs-electronicsuk.co.uk

Upload: others

Post on 31-Mar-2021

4 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

Part No: VW-190-07MU

1/25

This electric kit has to be installed by a professional workshop or a suitable qualified person.The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance!Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit!Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update).All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected.If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted.This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment!Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle’s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system.Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module.We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle’s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module from the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team!Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instruction must be observed!

Electric wiring kit for towbars / 7-pin / 12N / 12 Volt / ISO 1724

Skoda

KaroqKaroq ScoutKaroq Sportline

11/2017 >>02/2019 >>02/2019 >>

[email protected]

www.ecs-electronicsuk.co.uk

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 2: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

2/25

5x

M

X

A

C

M1

G

T

U

B

L1

L3

L4

L2

3x3x1x

3x

1x20 Amp.

20 Amp.1x

2x

10x3x

35-48 30-34

14-18

23-29

7-13

With trailer preparation

Without trailer preparation

Part No: **-***-***

*/**

Electric wiring kit for towbars / **-pin / 12 Volt / ISO *****

This electric kit has to be installed by a professional workshop or a suitable qualified person.The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance!Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit!Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update).All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected.If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted.This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment!Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle’s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system.Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module.We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle’s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module from the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team!Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instruction must be observed!

******** **/**** >>

************

[email protected]

www.ecs-electronicsuk.co.uk

Revision: * / **.**.******-***-***

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 3: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

3/25

SYMBOL EXPLANATION

TOOLS

Left (58-L) respectivelyRight (58-R) tail light

Stop light (54) / high mounted, third stop light (54)

Turn signal indicator left

Turn signal indicator right

Rear fog light(s)

Reversing light(s)

Trailer / trailer recognition

Permanent current power supply

Ground or Earth (31)

Ground connection battery terminal lug

Permanent power supply / 13pin socket, chamber 9

Charging wire for trailer battery / 13pin socket, chamber 10

+

15+

+

30+

Positive connection battery terminal lug

54 STOP

L

R

Reverse

B+/30

Fuse / fuse capacity 20 Ampère

Cigarette lighter /accessory socket

Loudspeaker / buzzer

Park Distance Control

Switch / source of function

Connect together

Disconnect

Look at / See further information

Look carefully at selected area

Present / Occupied / OK

Not present / Not occupied / Not OK

Acoustic indication

Attention / important advice

20 Amp.

20 Amp.

12V

1

ATTENTION!

ATTENTION! In order to avoid mal-functions and damage to the vehicle’s electrical system the earth terminal must be disconnected from the vehicle’s battery before starting work!

Both the trailer module and the vehicle’s control unit for the electrical system can be damaged during workon the data bus connections if the battery is not disconnected!

Please pay attention to the manufacturer’s instructions when disconnecting and reconnecting the vehicle’s battery!

The vehicle's cooling capacity may have to be increased when retrofitting a trailer coupling!You must observe the manufacturer's instructions!!

!Code

3:3

Note: It may be necessaryto check if this vehicle hasa stored radio code beforedisconnecting the battery!

Co

Co

ATTENTION!

ATTENTION! In order to avoid mal-functions and damage to the vehicle’s electrical system the earth terminal must be disconnected from the vehicle’s battery before starting work!

Both the trailer module and the vehicle’s control unit for the electrical system can be damaged during workon the data bus connections if the battery is not disconnected!

Please pay attention to the manufacturer’s instructions when disconnecting and reconnecting the vehicle’s battery!

The vehicle's cooling capacity may have to be increased when retrofitting a trailer coupling!You must observe the manufacturer's instructions!!

!Code

3:3

Note: It may be necessaryto check if this vehicle hasa stored radio code beforedisconnecting the battery!

Co

Co

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 4: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

2

3

4/25

Vehicle with trailer preparation4 19

49 57

BK/PE6 pin

BK10 pin

Pos. 22

Pos.

38Pos.

28

Pos.

44Black

10 pinBlack/Purple

BK/PE6 pin

BlackBlack/Purple

6 pin

Vehicle without trailer preparation 20 57

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 5: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

Vehicle with trailer preparation.

5/25

4x

4

5

6

1

1

2 3

23

4

1

2

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 6: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

6/25

1

3

SEAL WITH SILICONE.

4

X

INFO

XT

INFO

XT

2

Vehicle with trailer preparation.

7

8

9

X

X

Option 1 Option 2

Option 3

X

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 7: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

7/25

Option 1

!

!

X

Option 3 1 2 3

Vehicle with trailer preparation.

10

11

12

13

Option 21 2 3

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 25SOCKET CONNECTION

Page 8: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

8/25

M

M

M

1 2 3

4

M

10 mm1

2

G

Vehicle with trailer preparation.

14

15

16

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 9: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

9/25

A

21 3

1

2

Pos. 22

Pos.

38Pos.

28

Pos.

44

49 57

Vehicle with trailer preparation.

17

18

19

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 10: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

10/25

Vehicle without trailer preparation.

4x

20

21

22

1

1

2 3

34

5

1

2

2

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 11: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

11/25

Vehicle without trailer preparation.

23

Option 1

Option 2

12

3

1

2

3

T

T

T

XSEAL WITH SILICONE.

1

2

SEAL WITH SILICONE.

12

3

2

1

4 5

SEAL WITH SILICONE. 4

1

32

XT

X

INFO

X T

INFO X T

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 12: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

12/25

Vehicle without trailer preparation.

24

25

26

X

X

Option 1 Option 2

Option 3

X

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 25SOCKET CONNECTION

Page 13: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

13/25

Vehicle without trailer preparation.

28

29

Option 2 1 2 3

Option 3 1 2 3

M

M

M

1 2 3

4

30

27

Option 1

!

!

X

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 14: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

14/25

Vehicle without trailer preparation.

32

31

M

10 mm1

2

G

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 15: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

15/25

Vehicle without trailer preparation.

35

33

34

AB 1

2

3

21 3

L1

L3

L2 UL3

1

3

2

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 16: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

16/25

Vehicle without trailer preparation.

38

36

37

Body Control Module

Body Control Module

BCM-A BCM-C

1 54 8

2 6

3 7

BCM-A1 2

3

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 17: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

17/25

Vehicle without trailer preparation.

40

39

Can-busDatawireCAN

H

Pos. 17Orange/BrownCAN

L

BCM-A

LOCK Orange/BrownPos. 1

Orange/GreenPos. 2

CAN H

Pos. 1Orange/BrownCAN

L

1

2

3 L1

BCM-A

L2

Can-busDatawire

Pos. 16Orange/Green

Pos. 17Orange/Brown

4

Pos. 2

Orange/Greenor Green

Pos. 16

Orange/Greenor Green

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 18: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

18/25

Vehicle without trailer preparation.

43

41

42

2

1 BCM-A

1 2

3

BCM-C

BCM-C

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Pos. 58STOP

Page 19: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

19/25

Vehicle without trailer preparation.

45

44

LOCK

Black/RedPos. 3

1

2

3 L3

BCM-C

2

1 BCM-C

L4 4

Pos. 58Black/RedSTOP

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Pos. 3STOP

Page 20: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

20/25

Vehicle without trailer preparation.

47

46

8 5

7

6

4 1

3

2

BCM-A BCM-C

Body Control Module

12

3

4

1

2 3

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 21: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

Vehicle with and without trailer preparation.

21/25

Vehicle without trailer preparation.

50

48

49

+30

20 Amp.

20 Amp.

Pos. 28

1 2

Red/BluePos. 28

U

! MAX = 21WReverse

Optional

12S socket

Reverse

Reverse

PinkC

! Code3:3

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Page 22: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

22/25

Vehicle with and without trailer preparation.

51

52

53

Trailer Simulator for 7- and13-pin Sockets

Optional

L 54 STOPR

Reverse

Consult your supplier.

Set up trailer operation

VolkswagenSeatAudi

VolkswagenSeatAudi

!Diagnosis Services or diagnostic methods (local / offline):

Please note:

Always use the latest diagnostic version!The vehicle to be coded must be supported by the diagnostic service provider and already be implemented in the diagnostics version!Please contact your diagnostic service provider in case of any question.

- ODIS (page 24)- Hella Gutmann- VCDS- Autologic- Bosch / KTS- SP Diagnostic- SUN- Jifeline- Autocom- etc. pp.

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Functional test WARNING

OFF

VHz

Hz

Hz

Hz

A

V

COM10A

400mA

mA

V

mV

HOLD MINMAX RANGE

DC

Manual Range 60+

V

part no.

LIGHTMATE IILIGHTMATE III

Page 23: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

23/25

Vehicle with and without trailer preparation.

54

55

56

57

21W

21W

LED LED

LED

LED21W 21W

1

RL RL

RL

1RL

1RL

Adapter socketOptional

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Part No: **-***-***

*/**

Electric wiring kit for towbars / **-pin / 12 Volt / ISO *****

This electric kit has to be installed by a professional workshop or a suitable qualified person.The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance!Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit!Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update).All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected.If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted.This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment!Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle’s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system.Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module.We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle’s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module from the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team!Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instruction must be observed!

******** **/**** >>

************

[email protected]

www.ecs-electronicsuk.co.uk

Revision: * / **.**.******-***-***

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

7-pin 13-pin

Page 24: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

24/25

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

Set up trailer operation

Page 25: Skoda - ECS Electronics | Welcome Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook

25/25

Revision: 3 / 06.08.2021 VW-190-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

SOCKET CONNECTION

1-7 STOP

21W21W 21W 52W 3x21W 52W

DIN/ISO 1724

Pmax

Yellow Blue White Green Brown Red Black

1/L 2 3/31 4/R 5/58-R 6/54 7/58-L

L R

Colour

SOCKET CONNECTION

12

76

54

3

1

6

7

53

4

2

Yellow

Blue

White

Green

Brown

Red

Black