smart craft gauges owners guide
TRANSCRIPT
i
© 2
007
Mer
cury
Mar
ine
Smar
tCra
ft G
auge
s90
-898
2830
15 9
07
ii
TABLE OF CONTENTS
iii
System Tachometer/Speedometer
Basic Operation and Features.....................................................1Automatic Engine Detection Feature...........................................1Master Reset...............................................................................2Alarm Warnings...........................................................................3Warning Display Screens............................................................4Display Screens...........................................................................8System Speedometer Display Screens.......................................9Speedometer Quick CAL Calibration.........................................11Speedometer CAL 1 Calibration................................................11Speedometer CAL 2 Calibration ...............................................14System Tachometer Display Screens........................................15Tachometer Quick CAL Calibration...........................................17Tachometer CAL 1 Calibration..................................................18Tachometer CAL 2 Calibration..................................................21Troll Control Operation..............................................................25
System Tach/Speed Descriptive Text
Basic Operation and Features...................................................28Automatic Engine Detection Feature.........................................28Master Reset.............................................................................29Alarm Warnings with Descriptive Text.......................................30Display Screens.........................................................................31System Speedometer Display Screens.....................................32Speedometer Quick CAL Calibration.........................................34Speedometer CAL 1 Calibration................................................34Speedometer CAL 2 Calibration ...............................................37System Tachometer Display Screens........................................38Tachometer Quick CAL Calibration...........................................40Tachometer CAL 1 Calibration..................................................41Tachometer CAL 2 Calibration..................................................44Troll Control Operation..............................................................48
Smart Tow Tach/Speed GPS
Basic Operation and Features...................................................51
TABLE OF CONTENTS
iv
Automatic Engine Detection Feature.........................................52Master Reset.............................................................................52Alarm Warnings with Descriptive Text.......................................53Display Screens.........................................................................55Smart Tow Speedometer with GPS Display Screens................56Smart Tow Speedometer with GPS Quick CAL Calibration......58Smart Tow Speedometer with GPS CAL 1 Calibration..............59Smart Tow Speedometer with GPS CAL 2 Calibration .............62Smart Tow Tachometer Display Screens..................................63Smart Tow Tachometer Quick CAL Calibration.........................66Smart Tow Tachometer CAL 1 Calibration................................66Smart Tow Tachometer CAL 2 Calibration................................70Cruise Control Operation...........................................................74Precise Speed Control Calibration (Optional)............................76Launch Control Operation..........................................................78Creating a Customized Launch Setting.....................................80
SYSTEM TACHOMETER/SPEEDOMETER
1
Basic Operation and Features
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL 30158
System Tachometer System SpeedometerPower up: Each gauge will power up when the ignition is turnedon. The gauges will stay on as long as the ignition is on.Lights: Adjusts the brightness and contrast of the gauge.Buttons: The "MODE/SELECT" button is used for selectinginformation screens. The "+" and "‑" buttons are used for settingengine speed for troll control, and setting gauge calibrations.Troll control: Sets and controls the idle speed of the engine fortrolling without using the throttle.Engine Guardian System: Monitors the critical sensors on theengine for any early indication of problems. The system willrespond to a problem by reducing engine speed and alerting theoperator to a potentially damaging situation.Warning system: The system sounds the warning horn anddisplays the warning message.IMPORTANT: Optional sensors such as depth, fuel, paddle wheel,and steering angle, should always be connected to the starboardengine when using SmartCraft gauges version 4.0 or later.
Automatic Engine Detection FeatureThe System Tachometer/Speedometer has an automatic enginedetection feature. This feature automatically detects which enginetype is used and configures the gauge to match that engine type.
SYSTEM TACHOMETER/SPEEDOMETER
2
The first power up of the gauge, or after a Master Reset, the gaugewill display "AUTODETECT". Press the "MODE/SELECT" buttonto start the automatic engine detection feature and the gauge willdetermine the engine type. This will preset the data monitoringscreens to make the initial setup easier.
AUTODETECTENGINE SMARTSCREEN
PRESS MODE/SELECT TO START24298
If the gauge shows a warning of "NO STARBOARD ENGINE" or"MULTIPLE STARBOARD ENGINES", the engine location (portand starboard) must be selected by an authorized dealer equippedwith the computer diagnostic system (CDS) tool.
Master ResetReturns the gauge to the factory defaults through the Master Resetcommand.IMPORTANT: Performing a Master Reset will reset the unit to thefactory defaults, thus eliminating any installation and calibrationsperformed during set up of product.Press the "‑" and "+" buttons simultaneously for approximately 10seconds (until the graphic bars collide) to restore the unit to factorydefault settings. Press the "MODE/SELECT" button to confirm.
22660
MASTERRESET
MASTERRESETERASE CALIBRATION !
PRESS MODE/SELECT TO CONFIRM
SYSTEM TACHOMETER/SPEEDOMETER
3
Alarm WarningsNOTE: Alarm warnings are displayed, as shown, when used withengines prior to Gen I (2007).
3200 RPM
AL
b c
22663
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL- MODE
SPEED
0
2030 40
50
60
70
10
RESET
TROLL+TROLL
-
a
REDUCETHROTTLE
a - Display screenb - Engine Guardian Systemc - Alarm signal
When a problem is detected, the name of the offending alarmappears on the display.If the problem can cause immediate engine damage, the EngineGuardian System will respond to the problem by limiting enginepower. Immediately reduce the throttle speed and refer to thewarning messages on the following pages. Refer to the engineOperation, Maintenance, and Warranty Manual for furtherexplanation of the problem and the correct action to take.The alarm message will stay displayed until the "MODE/SELECT"button is pressed. If there are multiple alarms, these will cycle onthe display at five‑second intervals.If the "MODE/SELECT" button is pressed to display a differentscreen, the flashing alarm signal "AL" will appear in the upper rightcorner to indicate there still is a problem.
SYSTEM TACHOMETER/SPEEDOMETER
4
Warning Display ScreensWhen a problem is detected with the engine, the warning displayscreens will alert the operator to the potential problem. Refer to theengine Operation, Maintenance, and Warranty Manual for anexplanation of the problem and the correct action to take.
PROBLEM TACHOMETERDISPLAY
SPEEDOMETERDISPLAY
BATTERY ×ENGINE DATA BUS ×FAULT‑ HORN ×FAULT‑ IGNITION ×FAULT‑ INJECTOR ×FAULT‑ OIL PUMP ×FAULT‑ SENSOR ×FAULT‑ WATER TEMP ×LOW FUEL ×LOW OIL ×OIL TEMP ×OIL PSI ×OVERHEAT ×OVERSPEED ×PRESSURE ×RESERVE OIL ×WATER IN FUEL ×MAP ×MAT ×TPS ×
SYSTEM TACHOMETER/SPEEDOMETER
5
NOTE: Depending on the engine type, not all screens will apply.
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
OVERHEAT
PRESSURE
OVERSPEED
WATER
FAULT
RESERVE
FAULT
FAULT
7500 RPM
IN FUEL
HORN
90% REMAINING
OIL PUMP
INJECTOR22763
1
2
3
4
5
6
7
8
IMPORTANT: Refer to the engine Operation, Maintenance, andWarranty Manual for further explanation of the problem and thecorrect action to take. Contact the dealer if the problem persists.1. OVERHEAT: The engine has overheated.2. PRESSURE: There is insufficient water pressure in the
cooling system.3. OVERSPEED: Engine speed exceeded the maximum
allowable RPM.4. WATER IN FUEL: Water in the water separating fuel filter
reached the full level.5. FAULT - HORN: The warning horn is not functioning correctly.6. RESERVE OIL LOW - 2-Stroke outboard only: Oil level is
critically low in the engine‑mounted oil reservoir tank.7. FAULT - OIL PUMP: The oil pump has stopped functioning
electrically. No lubricating oil is being supplied to the engine.8. FAULT - INJECTOR: One or more of the fuel injectors have
stopped functioning electrically.
SYSTEM TACHOMETER/SPEEDOMETER
6
NOTE: Depending on the engine type, not all screens will apply.
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
FAULT
BATTERY
FAULT
FAULT
FAULT
FAULT
FAULTSENSOR
WATER TEMP
OIL TEMP22892
ENGINEDATA BUS
IGNITION
NO STARBOARD ENGINE
MULTIPLE STARBOARD ENGINE
8V 18V
9
10
11
12
13
14
15
16
9. FAULT - IGNITION: A problem has developed in the ignitionsystem.
10.BATTERY: The electrical system is not charging or the batterycharge is low.
11.ENGINE DATA BUS: The data communication link betweenthe tachometer and engine is not connected.
12.FAULT - SENSOR: One of the sensors is not functioningcorrectly.
13.FAULT - WATER TEMP: The sensor for measuring outsidelake/seawater temperature is not functioning correctly.
14.NO STARBOARD ENGINE: The instrument does not detectthe starboard engine computer. This usually indicates that nodata is being transferred from the engine's computer to thegauge. Check the wiring. Make sure both terminator resistorsare installed in the bus. Make sure the PCM/ECM's are notconfigured for the same location using computer diagnosticsystem (CDS).
15.MULTIPLE STARBOARD ENGINE: SmartCraft gauges arerecognizing multiple engines as starboard.
NOTE: In multiple engine applications, each engine must beassigned a position (starboard, port, starboard2, or port2) with aCDS before the system will function properly.16.OIL TEMPERATURE: The engine oil is overheating.
SYSTEM TACHOMETER/SPEEDOMETER
7
NOTE: Depending on the engine type, not all screens will apply.
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
FAULT
LOW FUEL
LOW OIL
FAULT
FAULT
FAULT
MAP
MAT
TPS
OIL PRESSURE
E F
E F
22897
17
18
19
21
22
20
17.OIL PRESSURE: There is insufficient oil pressure.18.LOW FUEL LEVEL: The fuel level in the fuel tank is critically
low. Stop for fuel immediately to avoid running out.19.LOW OIL LEVEL - 2-Stroke outboard only: The oil level in
the remote oil tank is low. Stop and refill the oil tankimmediately to avoid running out.
20.FAULT - MAP: Engine problem occurred. Have the enginechecked by a dealer.
21.FAULT - MAT: Engine problem occurred. Have the enginechecked by a dealer.
22.FAULT - TPS: Engine problem occurred. Have the enginechecked by a dealer.
SYSTEM TACHOMETER/SPEEDOMETER
8
Display ScreensTachometer Display Screen Speedometer Display Screen
Engine Break‑in (2‑Stroke outboard only) SpeedEngine Temperature Fuel UsedOil Temperature Cog/Sog ‑ If there is a GPS inputOil PSI Distance and Fuel to WaypointTrim and RPM Clock ‑ Air/Sea TempTrim and Water Pressure Instant and Average Fuel EconomyWater Pressure Trip OdometerBattery Voltage and Engine Hours Fuel Tank LevelsFuel Flow and Fuel Used Oil Tank LevelsSpeed and Sea Temperature Fresh Water LevelsBattery Voltage Waste Water levels% Fuel Remaining (Fuel Tank 1) Steering Angle (MerCruiser only)DepthTrim Position Dual Engine
Fuel PSI Trim and RPM SynchronizerTrailer and RPMRPMQuick Reverence ScreenBattery, Temperature, PSI
SYSTEM TACHOMETER/SPEEDOMETER
9
System Speedometer Display ScreensNOTE: Depending on the engine type, not all screens will apply.
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
5:30 PM
70 60 FAIR
FSEA
FUEL
E FGALLONS60
OIL
E FGALLONS0.6
RPM SYNCH
TRIM SYNCH
STBD 23462PORT
STBDPORT
1
2
3
4
5
When the ignition is turned on, the speedometer will show the lastscreen that was displayed before the ignition was turned off.Press "MODE/SELECT" to change display screens. Revert backto the previous screen by pressing and holding "MODE/SELECT"for two seconds.NOTE: Readings can be displayed in English (U.S.) or metric.Refer to Speedometer Cal 1 Calibrations.NOTE: The descriptions may not be in order on the gauge. Theorder may change depending on engine type.1. Clock - Temp: Clock, air temperature, and water temperature.
The air and water temperature sensors must be connected toobtain display readings.
2. Fuel Level: Displays the amount of fuel remaining.3. Oil Level: Displays the amount of engine oil remaining
(2‑Stroke outboard only), or water/waste tank level (ifattached).
4. RPM Synchronizer: Dual engines only ‑ Monitors therevolutions of both engines.
5. Trim Synchronizer: Dual engines only ‑ Displays the trimposition of both engines. Simplifies keeping trim levels equal.
SYSTEM TACHOMETER/SPEEDOMETER
10
NOTE: Depending on the engine type, not all screens will apply.
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
300INST M/G AVG
1.5 3.2
23477
ESTIMATED RANGE
MILES
TRIP
25MILES
42.3 MPH
STEERING ANGLE
52 PORT
6
7
8
9
10
6. Range: The estimated range is based on boat speed, fuelconsumption, and fuel remaining in the tank. The numbersdisplayed are an estimate of the distance you can travel withthe remaining fuel. Speed input required (paddle wheel, pitotpressure or GPS).
7. Fuel Economy: Displays the average "AVG" fuelconsumption as well as Instantaneous "INST" fuel economy.The numbers displayed indicate miles per gallon "M/G" orkilometers per liter "KM/L". Fuel Reset: To reset, select thedisplay screen and press "MODE/SELECT" and "‑"simultaneously.
8. Trip Odometer: Displays the distance traveled since thegauge was last reset to zero. Trip Reset: To reset, select thedisplay screen and press "MODE/SELECT" and "‑"simultaneously.
9. Digital Speedometer: Displays the boat speed in miles perhour, kilometers per hour, or nautical miles per hour. Thespeedometer will use the paddle wheel for its low speedreadings, but will switch to the speedometer or GPS (ifconnected) for high speed readings. The transition pointsetting is described in Cal 2.
SYSTEM TACHOMETER/SPEEDOMETER
11
10.Steering Angle: Displays the relative position of the steeringsystem. Available on Mercury MerCruiser models only. Asteering angle sensor must be installed on the engine.
Speedometer Quick CAL Calibration
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
24159
SC1000 System SpeedometerThis calibration is for setting the lighting and contrast.1. Press the "MODE/SELECT" and "+" buttons simultaneously
for two seconds to bring up the "Quick Cal" display screen.2. Press the "‑" or "+" button to select the option choice displayed
in the [ ] brackets on the screen.3. Press "MODE/SELECT" to save the setting and advance
through the calibration selections.
Quick CAL
LIGHT[DOWN] [SAVE] [ UP ]
23517
Adjusts the brightness of the gauge lighting.
CONTRAST[DOWN] [SAVE] [ UP ]
23519
Adjusts the contrast of the display screen.
Speedometer CAL 1 CalibrationThis calibration turns the system display screens on and off.NOTE: Depending on the engine type, not all screens will apply.
SYSTEM TACHOMETER/SPEEDOMETER
12
1. Press the "MODE/SELECT" and "+" buttons simultaneouslyfor approximately six seconds to bring up the "Cal 1" displayscreen.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration selections.
Remote Lighting and Contrast
[ NO ] [SAVE] [YES ]23532
REMOTE LCD LIGHT ?Adjusts the lighting levels on all gaugessimultaneously from this gauge.
[ NO ] [SAVE] [YES ]
23533
REMOTE LCD CONTRAST ? Adjusts the contrast of another SystemTachometer/Speedometer simultaneously fromthis gauge.
Time
( NO ) ( SKIP ) ( EDIT )23534
CALIBRATION 1 TIME Sets the time. Select "EDIT" to format the time
or "SKIP" to advance to the next screen.
(DOWN) (SAVE) ( UP )23535
CALIBRATION 1 TIME FORMAT 12H - M, D, Y
Formats the time as either 12 hourmonth‑day‑year or as 24 hour day‑month‑year.Select "DOWN" or "UP" to change the format.
(DOWN) (SAVE) ( UP )23536
CALIBRATION HOUR
1:42PM Adjusts the hours to match your local time.Select "DOWN" or "UP" to change the hoursetting.
(DOWN) (SAVE) ( UP )23538
CALIBRATION MINUTE
1:42PM Adjusts the minutes to match your local time.Select "DOWN" or "UP" to change the minutesetting.
Display Units
[DOWN] [SAVE] [ UP ]23539
DISPLAY UNITS
ENGLISH Changes units of measurement betweenEnglish or metric. Select "DOWN" or "UP" tochange between English or metric units.
SYSTEM TACHOMETER/SPEEDOMETER
13
Display Units
23540
SPEED UNITS
MPH[DOWN] [SAVE] [ UP ]
Changes the units in which speed is displayed.Choose from: MPH (Miles Per Hour), KN(Knots), or KMH (Kilometers Per Hour).
Display Screens
[ NO ] [SAVE] [ YES ]23542
STEERING ANG. SCREEN ?
YESThe steering angle is displayed "YES" or off"NO". The steering angle sensor must be set to"YES" in the tachometer "CAL 2" externalsensors calibration.
23543
TEMP/CLOCK SCREEN ?
YES[ NO ] [SAVE] [ YES ]
The split screen showing air temperature andtime is displayed "YES" or off "NO".
( NO ) (SAVE) ( YES )23544
FUEL USED SCREEN ?
YES The fuel used screen is displayed "YES" or off"NO".
(SKIP) (EDIT)30164
CALIBRATION 1 FUEL USED Selects how fuel used is calibrated. Press "+" to
select "EDIT" or "SELECT" to by‑pass how thefuel used is calibrated.
[FUEL]
FUEL USED CAL : ENTER MULTIPLIER, OR REFUELED ?
[MULT]30166
Selects how fuel used is calibrated with amultiplier or with refueling. Press "‑" to selectmultiplier "MULT" or "+" to select refueling"FUEL."
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : MULTIPLIER = 1.0
30167
Adjusts multiplier between 0.50 and 1.50. Press"‑" to select "DOWN", or "+" to select "UP."
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : AMOUNT REFUELED = 0.0 G
30168
Adjust fuel used calibration using the amount offuel replaced. Press "‑" to select "DOWN", or "+"to select "UP."
( NO ) (SAVE) ( YES )23545
TRIP SCREEN
YES The trip screen is displayed "YES" or off "NO".
SYSTEM TACHOMETER/SPEEDOMETER
14
Display Screens
( NO ) (SAVE) ( YES )23546
FUEL MGMNT SCREEN
YES The fuel management screen is displayed"YES" or off "NO".
Simulator Mode
[ NO ] [SAVE] [ YES ]23547
SIMULATOR MODE
NO Enables the simulation mode. (Used fordemonstration purposes only.)
Exit
[ NO ] [ YES ] [CAL 2]23549
SIMULATOR MODE
EXIT ? Press "MODE/SELECT" to exit. Press "‑" to goto the start of CAL 1. Press "+" to continue to"CAL 2".
Speedometer CAL 2 CalibrationThis calibration configures the system sensor inputs.NOTE: Screens may vary depending upon the version of the gaugeand the engine type.1. Press and hold the "MODE/SELECT" and "+" buttons
simultaneously for approximately nine seconds until the "CAL2" display screen appears.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration selections.
External Sensors
(SKIP) (EDIT)23569
CALIBRATION 2 EXTERNAL SENSORS
Selects and calibrates external sensors that areinstalled in the system. Select (SKIP) to proceedto the next selection. Select (EDIT) to proceedto external sensor selection.
(SAVE) ( YES )23574
CALIBRATION 2 EXTERNAL SENSORS
( NO )AIRTEMP ? YES
Is an air temperature sensor installed? Press "‑"to select "NO" or "+" to select "YES".
SYSTEM TACHOMETER/SPEEDOMETER
15
External Sensors
(SAVE) ( YES )23582
CALIBRATION 2 EXTERNAL SENSORS
( NO )GPS ? YES
Is a GPS sensor installed? Press "‑" to select"NO" or "+" to select "YES".
(SAVE) ( YES )23596
CALIBRATION 2 EXTERNAL SENSORS
( NO ) USE GPS SPEED ? YES
Use the GPS input to drive the speed display?Press "‑" to select "NO" or "+" to select "YES".
(SAVE) ( UP )23592
CALIBRATION 2 SEA TEMP
(DOWN)OFFSET = 0 F
Adjust the seawater temperature sensor tocorrect display readings that are too high/low.Press "‑" or "+" to calibrate the temperaturedisplay "DOWN" or "UP".
(SAVE) ( YES )23617
CALIBRATION 2 TROLL CONTROL ?
( NO )ENABLED
To enable troll control select "YES", to disableselect "NO".
(SAVE) ( CAL1 )23618
CALIBRATION 2
( NO )EXIT ? Press "MODE/SELECT" to exit. Press "‑" to go
to the start of CAL 2. Press "+" to continue to"CAL 1".
System Tachometer Display Screens
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
23495
BREAK-IN TIME
MINLEFT65
OK OK OKBAT TMP PSI
TRIM WATER PSI
12.51.5
12.5 H20PSI
F125
1
2
3
4
5
6
TRIM 1.5
When the ignition is turned on, the tachometer will display the lastscreen that was displayed before the ignition was turned off.
SYSTEM TACHOMETER/SPEEDOMETER
16
Press "MODE/SELECT" to change display screens. Revert backto the previous screen by pressing and holding "MODE/SELECT"for two seconds.NOTE: Readings can be displayed in English (U.S.) or metric.Refer to Tachometer Calibration.1. Engine Break-in: Displays the time remaining on the break‑in
period of a new engine. This screen will automaticallydisappear after the break‑in period is complete.
2. Quick Reference Screen: Indicates that the battery, enginetemperature, and pressures are operating properly.
3. Temperature: Displays the engine coolant temperature.4. Power Trim Angle: Displays the trim angle of the outboard or
sterndrive up to the maximum trim angle and then displays thetrailer angle. 0 = down, 10 = maximum trim, and 25 = full trailer.
5. Power Trim Angle/Water Pressure: Displays the trim angleof the engine and cooling system water pressure.
6. Water Pressure: Displays the cooling system water pressureat the engine.
NOTE: Depending on the engine type, not all screens will apply.
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
23511
OILPSI12.5
VOLTS HOURS
12.2 1.5
RPM3500
GPH USED
12.54.5FUEL
SPEED SEA TEMP
MPH 45 45 F
7
8
9
10
11
12
35 FT
7. Oil Pressure: Displays the engine oil pressure in "PSI" or"BAR".
SYSTEM TACHOMETER/SPEEDOMETER
17
8. Battery Voltage: Displays the voltage level (condition) of thebattery. Also records the running time of the engine.
9. Fuel Flow: Displays the engine fuel use in gallons per hour orliters per hour.
10.Digital Tachometer: Displays the engine speed in revolutionsper minute (RPM).
11.Water Depth: Displays the depth of water under thetransducer if connected. The water depth screen can beturned on or off in CAL 1 calibration. The alarm can be set totrigger whenever the boat moves into water shallower than thealarm level. Refer to CAL 2 calibration for water depth alarmand offset settings.
NOTE: A depth transducer (purchased separately) must beconnected to the system for this screen to operate.12.Speed/Temp: Displays a split screen of seawater
temperature and vessel speed.NOTE: A speed input sensor must be connected to the system forthis screen to operate.
Tachometer Quick CAL Calibration
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
30214
SC1000 System TachometerThis calibration is for setting lighting and contrast.1. Press the "MODE/SELECT" and "+" buttons simultaneously
for approximately two seconds or until the "QUICK CAL"screen appears.
SYSTEM TACHOMETER/SPEEDOMETER
18
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration screens.
Quick CAL
LIGHT[DOWN] [SAVE] [ UP ]
23517
Adjusts the brightness of the gauge lighting.
CONTRAST[DOWN] [SAVE] [ UP ]
23519
Adjusts the contrast of the display screen.
Tachometer CAL 1 CalibrationThis calibration turns the system screens on and off.NOTE: The screens may vary depending upon the version of thegauge.1. Press and hold the "MODE/SELECT" and "+" buttons for
approximately seven seconds until the "CAL 1" screenappears.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration screens.
Tachometer CAL 1 Calibration ‑ Remote Light and Contrast
[SAVE] [ YES ]23620
REMOTE SCREENS ?
[ NO ]
If "YES" is selected, then screen changes madeon this tachometer will effect all tachometers inthe system. All tachometers need the screen setto "YES" for this function to work.
[ NO ] [SAVE] [YES ]23532
REMOTE LCD LIGHT ?Adjusts the lighting levels on all gaugessimultaneously from this gauge. If "YES" isselected, then lighting level changes made onthis tachometer will effect all tachometers in thesystem. All tachometers need the screen set to"YES" for this function to work.
SYSTEM TACHOMETER/SPEEDOMETER
19
Tachometer CAL 1 Calibration ‑ Remote Light and Contrast
[ NO ] [SAVE] [YES ]
23533
REMOTE LCD CONTRAST ?
Adjusts the contrast of another System/SmartTow Tachometer simultaneously from thisgauge. If "YES" is selected, then contrast levelchanges made on this tachometer will effect alltachometers in the system. All tachometersneed the screen set to "YES" for this function towork.
Tachometer CAL 1 Calibration ‑ Trim
[SAVE] [ YES ]23621
HIGH RESOLUTION TRIM ?
[ NO ]
Enables the trim angle to be displayed in 0.1°increments if "YES" is selected.
[SAVE] [ YES ]23641
TRIM POPUP ?
[ NO ]
The trim display screen pops up when the trimsetting is changed if "YES" is selected.
TRIM CALIBRATIONCALIBRATION 1
[SKIP] [EDIT]23910
Select "EDIT" to calibrate the gauge to thestandard 0 ‑ 10° unit trim and 11 ‑ 25° trailerposition scale. Select "SKIP" to advance to thenext selection.
TRIM FULL DOWNCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SKIP] [SAVE]
23911
Trim the system to the full down position, thenpress the "+" button to save the setting.
TRIM FULL UPCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SKIP] [SAVE]
23912
Trim the system to the full up position, thenpress the "+" button to save the setting.
TRIM TO TRAILER POINTCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SKIP] [SAVE]
23919
Trim the system to the trailer point, then pressthe "+" button to save the setting.
Tachometer CAL 1 Calibration ‑ Display Units
[DOWN] [SAVE] [ UP ]23539
DISPLAY UNITS
ENGLISHChanges units of measure between English ormetric. Select "DOWN" or "UP" to changebetween "ENGLISH" or "METRIC" units ofmeasure.
SYSTEM TACHOMETER/SPEEDOMETER
20
Tachometer CAL 1 Calibration ‑ Display Units
23540
SPEED UNITS
MPH[DOWN] [SAVE] [ UP ]
Changes the units in which speed is displayed.Choose from: MPH (Miles Per Hour), KN(Knots), or KMH (Kilometers Per Hour).
Tachometer CAL 1 Calibration ‑ Display Screens
QUICK REF SCREEN ?
[ NO ] [SAVE] [ YES ]23978
The quick reference screen is displayed "YES"or off "NO".
ENGINE TEMP SCREEN ?
[ NO ] [SAVE] [ YES ]23783
The engine temperature screen is displayed"YES" or off "NO".
OIL TEMP SCREEN ?
[ NO ] [SAVE] [ YES ]23786
The oil temperature screen is displayed "YES"or off "NO".
OIL PRESS SCREEN ?
[ NO ] [SAVE] [ YES ]23787
The oil pressure screen is displayed "YES" oroff "NO".
TRIM AND PSI SCREEN ?
[ NO ] [SAVE] [ YES ]23788
The split screen showing trim angle and waterpressure is displayed "YES" or off "NO".
WATER PSI SCREEN ?
[ NO ] [SAVE] [ YES ]23789
The water pressure screen is displayed "YES"or off "NO".
TRIM AND RPM SCREEN ?
[ NO ] [SAVE] [ YES ]23979
The split screen showing trim angle and engineRPM is displayed "YES" or off "NO".
RPM SCREEN ?
[ NO ] [SAVE] [ YES ]23980
The engine RPM screen is displayed "YES" oroff "NO".
SYSTEM TACHOMETER/SPEEDOMETER
21
Tachometer CAL 1 Calibration ‑ Display Screens
FUEL USED SCREEN ?
[ NO ] [SAVE] [ YES ]23981
The fuel used screen is displayed "YES" or off"NO".
VOLT / HOUR SCREEN ?
[ NO ] [SAVE] [ YES ]23982
The split screen showing volts and engine hoursis displayed "YES" or off "NO".
SPEED / SEA SCREEN ?
[ NO ] [SAVE] [ YES ]23983
The split screen showing speed and seatemperature is displayed "YES" or off "NO".
DEPTH SCREEN ?
[ NO ] [SAVE] [ YES ]23984
The depth screen is displayed "YES" or off"NO".
[ NO ] [SAVE] [ YES ]23547
SIMULATOR MODE
NO Enables the simulation mode. (Used fordemonstration purposes only.)
[ NO ] [ YES ] [CAL 2]23549
SIMULATOR MODE
EXIT ? Press "MODE/SELECT" to exit. Press "‑" to goto the start of CAL 1. Press "+" to continue to"CAL 2".
Tachometer CAL 2 CalibrationThis calibration configures the system sensor inputs.NOTE: The screens may vary depending upon the version of thegauge.1. Press and hold the "MODE/SELECT" and "+" buttons for
approximately ten seconds until the "CAL 2" screen appears.2. Press the "‑" or "+" button to select the option choice displayed
in the [ ] brackets on the screen.3. Press "MODE/SELECT" to save the setting and advance
through the calibration screens.FUEL TANK CALIBRATIONThere are three methods for calibrating the fuel tank levelmonitoring feature:
SYSTEM TACHOMETER/SPEEDOMETER
22
1. Do nothing. The linear readout is based on raw sensor values.This mode does not factor in irregular tank shapes.
2. Performing the tank calibration procedure without adding fuel;the System Tachometer/Smart Tow Tachometer will supplyan estimated range value based on linear interpolation of thesensor range values. This mode does not factor in irregulartank shapes. You must edit the tank calibration by entering anumerical value for the capacity of the fuel tank. The linearreadout is based on raw sensor values.
3. Performing the tank calibration procedure with adding fuel ateach calibration point; the System Tachometer/Smart TowTachometer will display an estimated range value that factorsin the tank shape. You must edit the tank calibration by addingfuel for 1/4, 1/2, 3/4, and full. Failure to edit the tank calibrationwill automatically default the fuel level to the liter/galloncapacity.
CAL 2 Tachometer Calibration ‑ Tank 1 and 2 Level Calibration
FUEL TANK 1 CAPACITYCALIBRATION 2
CAPACITY = 26.2 G[DOWN] [SAVE] [ UP ]
23992
Enter the capacity of the tank. Select "DOWN"or "UP" to set the tank capacity. Then press"SAVE". This option is the same for tank 1 as itis for tank 2.
FUEL TANK 1CALIBRATION 2
[SKIP] [EDIT]23993
Select "EDIT" to enter the calibration mode ofthe fuel tank. The calibration procedure is thesame for tank 1 as it is for tank 2. Select "EDIT"to begin tank level calibration.
DEFAULT CALIBRATION,TANK CALIBRATION :
OR ADD FUEL ?[DFLT] [ADD ]
23994
Select "DFLT" to let SmartCraft calibrate thetank levels. Select "ADD" to calibrate the tanklevels by adding fluid to the tank.
EMPTY TANKCALIBRATING :
THEN PRESS PLUS BUTTON[SKIP] [SAVE]
23995
Empty the tank. Select "SAVE" to calibrate thetank level to empty.
FILL TANK TO 1/4
THEN PRESS PLUS BUTTON[SAVE]
30427
Fill the tank to 1/4 full. Select "SAVE" to calibratethe tank level to 1/4 full.
SYSTEM TACHOMETER/SPEEDOMETER
23
CAL 2 Tachometer Calibration ‑ Tank 1 and 2 Level Calibration
FILL TANK TO ½
THEN PRESS PLUS BUTTON[SAVE]
30428
Fill the tank to 1/2 full. Select "SAVE" to calibratethe tank level to 1/2 full.
FILL TANK TO 3/4
THEN PRESS PLUS BUTTON[SAVE]
30429
Fill the tank to 3/4 full. Select "SAVE" to calibratethe tank level to 3/4 full.
FILL TANK TO FULL
THEN PRESS PLUS BUTTON[SAVE]
30430
Fill the tank to full. Select "SAVE" to calibratethe tank level to full.
TANK 2 INPUTOIL TANK
CALIBRATION 2
[SAVE][DOWN] [ UP ]24148
Select tank 2 input: oil tank, fuel tank 2, watertank, waste tank, or not installed.
EXTERNAL SENSORS
CAL 2 Tachometer Calibration ‑ External Sensors
EXTERNAL SENSORS ?CALIBRATION 2
[SKIP] [EDIT]24006
Selects and calibrates external sensors that areinstalled in the system. Select "SKIP" to proceedto the speed options. Select "EDIT" to proceedto external sensor selection.
EXTERNAL SENSORSCALIBRATION 2
PITOT SENSOR ? YES[ NO ] [SAVE] [YES ]
24007
Is the boat equipped with a pitot sensor tomeasure boat speed? Press "‑" to select "NO"or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
PADDLE SENSOR ? YES[ NO ] [SAVE] [YES ]
24008
Is the boat equipped with a paddle wheel tomeasure boat speed? Press "‑" to select "NO"or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
TRIM SENSOR ? YES[ NO ] [SAVE] [YES ]
24009
Is the boat equipped with a trim sensor? Press"‑" to select "NO" or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
SEA TEMP ?[ NO ] [SAVE] [YES ]
24010
YESIs the boat equipped with a seawatertemperature sensor? Press "‑" to select "NO" or"+" to select "YES".
SYSTEM TACHOMETER/SPEEDOMETER
24
CAL 2 Tachometer Calibration ‑ External Sensors
EXTERNAL SENSORSCALIBRATION 2
STEERING SENSOR ?[ NO ] [SAVE] [YES ]
24011
YES Is the boat equipped with a steering sensor?Press "‑" to select "NO" or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
INVERT STEERING ?[ NO ] [SAVE] [YES ]
30432
YESChanges the position (direction) of the steeringdisplay. Press "‑" to select "NO" or "+" to select"YES".
SPEED OPTIONCALIBRATION 2
[SKIP] [EDIT]24012
This section configures the following speedsensors. Select "EDIT" to calibrate the sensors.Select "SKIP" to proceed to the depth sensorscreen.
PITOT SENSOR100 PSI TYPE
CALIBRATION 2
[ NO ] [SAVE] [YES ]24014
Select pitot transducer type. Choose between100 or 200 psi. (100 psi is the most common.)
PITOT SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24018
MULTIPLIER = 1.00
Adjust the pitot pressure sensor to correctdisplay readings that are too high/low. Press "‑"or "+" to calibrate the pitot sensor multiplier"DOWN" or "UP".
PADDLE SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24021
PULSEFACTOR = 3.0
Adjust paddle wheel frequency to correctdisplay readings that are too high/low. Press "‑"or "+" to calibrate the paddle sensor pulse factor"DOWN" or "UP".
TRANSITION SPEEDCALIBRATION 2
[DOWN] [SAVE] [ UP ]24022
TRANSITION = 30 MPH
Set the speed at which the gauge stops readingthe paddle wheel and starts using pitot sensorto measure boat speed. Press "‑" or "+" tocalibrate the transition speed "DOWN" or "UP".
DEPTH SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24023
OFFSET = 3 FEET
Electronically configure a depth offset. Enteringa negative number gives you a waterline offset.A positive number gives you a keel offset. Press"‑" or "+" to calibrate the depth sensor offset"DOWN" or "UP".
DEPTH ALARMCALIBRATION 2
[DOWN] [SAVE] [ UP ]24024
LEVEL = 2.5 FEET
Enter a depth value. When the depth transducerreads that value or below, the shallow wateralarm will sound. Press "‑" or "+" to calibrate thedepth alarm level "DOWN" or "UP".
[ NO ] [ YES ] [CAL 1]24025
CALIBRATION 2
EXIT ? Press "MODE/SELECT" to exit. Press "‑" to goto the start of CAL 2. Press "+" to continue to"CAL 1."
SYSTEM TACHOMETER/SPEEDOMETER
25
Troll Control OperationNOTE: The troll control feature is only available on the SystemTachometer and Speedometer.
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLLMODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
a a
Troll Speed On
10.5 ACTMPH 12.0
PUSH SELECT TO DISENGAGE
SETMPH
feTroll Speed On
1000 ACTRPM 1500
PUSH SELECT TO DISENGAGE
SETRPM
dc
FAIR
FSEA70 62
10:35TR
b b
30350
a - Increase troll speedb - Decrease troll speedc - Actual RPM
d - Set RPMe - Actual MPHf - Set MPH
NOTE: Troll control may not be available on all engine models.NOTE: The troll control minimum and maximum range may changedepending on engine type.Set the troll control by using the System Tachometer orSpeedometer. The speedometer will set the speed in MPH, KPH,or KN, while the tachometer will set the speed in RPM.The troll control can be shut off at anytime by adjusting the throttleor by pushing the "MODE/SELECT" button when in the troll displayscreen.When the troll control is shut off, the system will remember the setspeed. When the troll control is engaged, it will return to the setspeed.
SYSTEM TACHOMETER/SPEEDOMETER
26
The display screen will revert back to the previous screen after fiveseconds of inactivity. Push the "+" or "‑" button to reactivate thetroll control display screen.When the troll control is engaged and not in the troll control displayscreen, a flashing "TR" signal will appear in the upper left cornerof the screen to indicate the troll control is still active.SETTING TROLL CONTROL
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
600575PUSH SELECT TO DISENGAGE
TROLL SPEED ON OFFACTRPM
SETRPM
TROLL SPEED ON OFF
PUSH SELECT TO DISENGAGE
3.02.5 ACTMPH
SETMPH
SETMPH
TROLL SPEED TOO FAST
REDUCE TROLL SPEED
7.54.5 ACTMPH
SETMPH
TROLL SPEED TOO SLOW
INCREASE TROLL SPEED
3.02.5 ACTMPH
c d 23035
a afe
b b
a - Increase troll set speedb - Decrease troll set speedc - Setting is too fast, reduce set troll speedd - Setting is too slow, increase set troll speede - Actual speedf - Set speed
1. With the engine running, shift the engine into gear. Set theengine speed at idle.
2. Push in either the "+" or "‑" buttons to bring up the troll controldisplay screen.
3. Press "MODE/SELECT" to engage the troll control.
SYSTEM TACHOMETER/SPEEDOMETER
27
4. Use the "+" and "‑" buttons to set the desired speed. Use "+"to increase the set speed and use "‑" to decrease the setspeed.
5. If the troll speed is set to a higher speed than the troll controlcan maintain, the "TROLL SPEED TOO FAST" display willappear. Reduce the set troll speed.
6. If the troll speed is set to a slower speed than the troll controlcan maintain, the "TROLL SPEED TOO SLOW" display willappear. Increase the set troll speed.
CANCELING TROLL CONTROLThere are three ways to cancel the troll control:• Press the "MODE/SELECT" button when in the troll display
screen.• Move the throttle to a different speed.• Shift the engine into neutral.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
28
Basic Operation and FeaturesNOTE: Descriptive text alarm warning screens are displayed withGen I (2007) engines and newer.
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL 30158
System Tachometer System SpeedometerPower up: Each gauge will power up when the ignition is turnedon. The gauges will stay on as long as the ignition is on.Lights: Adjusts the brightness and contrast of the gauge.Buttons: The "MODE/SELECT" button is used for selectinginformation screens. The "+" and "‑" buttons are used for settingengine speed for troll control, and setting gauge calibrations.Troll control: Sets and controls the idle speed of the engine fortrolling without using the throttle.Engine Guardian System: Monitors the critical sensors on theengine for any early indication of problems. The system willrespond to a problem by reducing engine speed and alerting theoperator to a potentially damaging situation.Warning system: The system sounds the warning horn anddisplays the warning with descriptive text.IMPORTANT: Optional sensors such as depth, fuel, paddle wheel,and steering angle, should always be connected to the starboardengine when using SmartCraft gauges version 4.0 or later.
Automatic Engine Detection FeatureThe System Tachometer/Speedometer has an automatic enginedetection feature. This feature automatically detects which enginetype is used and configures the gauge to match that engine type.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
29
The first power up of the gauge, or after a Master Reset, the gaugewill display "AUTODETECT". Press the "MODE/SELECT" buttonto start the automatic engine detection feature and the gauge willdetermine the engine type. This will preset the data monitoringscreens to make the initial setup easier.
AUTODETECTENGINE SMARTSCREEN
PRESS MODE/SELECT TO START24298
If the gauge shows a warning of "NO STARBOARD ENGINE" or"MULTIPLE STARBOARD ENGINES", the engine location (portand starboard) must be selected by an authorized dealer equippedwith the computer diagnostic system (CDS) tool.
Master ResetReturns the gauge to the factory defaults through the Master Resetcommand.IMPORTANT: Performing a Master Reset will reset the unit to thefactory defaults, thus eliminating any installation and calibrationsperformed during set up of product.Press the "‑" and "+" buttons simultaneously for approximately 10seconds (until the graphic bars collide) to restore the unit to factorydefault settings. Press the "MODE/SELECT" button to confirm.
22660
MASTERRESET
MASTERRESETERASE CALIBRATION !
PRESS MODE/SELECT TO CONFIRM
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
30
Alarm Warnings with Descriptive TextNOTE: Descriptive text alarm warning screens are displayed withGen I (2007) engines and newer.
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL 30158
System Tachometer System SpeedometerWhen a problem is detected, the "SYS FAULT" alarm appears onthe display. Press the "+" button to show the faulty component. Theupper bar in this screen displays the system where the fault islocated. The faulty component is described in the scrolling text.Press the "+" button for more information. This screen gives adetailed description of the fault in the scrolling text. Press the "+"button to view the required corrective action.The alarm message will stay displayed until the "‑" button ispressed. If there are multiple alarms, press the "MODE/SELECT"button to display.If a problem can cause immediate engine damage, the EngineGuardian System will respond to the problem by limiting enginepower. Immediately reduce the throttle speed to idle and refer tothe warning messages on the following pages. Refer to theappropriate service manual for further explanation of the problemand the correct action to take.If the "MODE/SELECT" button is pressed to display a differentscreen, the flashing alarm signal "AL" will appear in the upper rightcorner to indicate there still is a problem.
Alarm Warning with Descriptive Text
[ SHOW ]
SYS FAULT
24184
The "SYS FAULT" bar indicates there is aproblem in the system. "SHOW" displaysthe faulty component.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
31
Alarm Warning with Descriptive Text
[ MORE ][ NEXT ][ EXIT ]
STBD SYSTEM FAULT
<FAULTY COMPONENT>
24186
STBD SYSTEM FAULT The top bar indicates the system with thefaulty component. The scrolling textdisplays the faulty component. "NEXT"displays the next fault. "MORE" displays adetailed description of the fault.
[ ACTION ][ NEXT ][ EXIT ]
STBD SYSTEM FAULT
<FAULT DESCRIPTION>
24187
The scrolling text explains in detail thedescription of the fault. "ACTION" displaysthe course of action required by theoperator.
[ BACK ][ NEXT ][ EXIT ]
STBD SYSTEM FAULT
<CORRECTIVE ACTION>
24189
The scrolling text displays the course ofaction required by the operator.
Display ScreensTachometer Display Screen Speedometer Display Screen
Engine Break‑in (2‑Stroke outboard only) SpeedEngine Temperature Fuel UsedOil Temperature Cog/Sog ‑ If there is a GPS inputOil PSI Distance and Fuel to WaypointTrim and RPM Clock ‑ Air/Sea TempTrim and Water Pressure Instant and Average Fuel EconomyWater Pressure Trip OdometerBattery Voltage and Engine Hours Fuel Tank LevelsFuel Flow and Fuel Used Oil Tank LevelsSpeed and Sea Temperature Fresh Water LevelsBattery Voltage Waste Water levels% Fuel Remaining (Fuel Tank 1) Steering Angle (MerCruiser only)DepthTrim Position Dual Engine
Fuel PSI Trim and RPM SynchronizerTrailer and RPMRPMQuick Reverence ScreenBattery, Temperature, PSI
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
32
System Speedometer Display ScreensNOTE: Depending on the engine type, not all screens will apply.
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
5:30 PM
70 60 FAIR
FSEA
FUEL
E FGALLONS60
OIL
E FGALLONS0.6
RPM SYNCH
TRIM SYNCH
STBD 23462PORT
STBDPORT
1
2
3
4
5
When the ignition is turned on, the speedometer will show the lastscreen that was displayed before the ignition was turned off.Press "MODE/SELECT" to change display screens. Revert backto the previous screen by pressing and holding "MODE/SELECT"for two seconds.NOTE: Readings can be displayed in English (U.S.) or metric.Refer to Speedometer Cal 1 Calibrations.NOTE: The descriptions may not be in order on the gauge. Theorder may change depending on engine type.1. Clock - Temp: Clock, air temperature, and water temperature.
The air and water temperature sensors must be connected toobtain display readings.
2. Fuel Level: Displays the amount of fuel remaining.3. Oil Level: Displays the amount of engine oil remaining
(2‑Stroke outboard only), or water/waste tank level (ifattached).
4. RPM Synchronizer: Dual engines only ‑ Monitors therevolutions of both engines.
5. Trim Synchronizer: Dual engines only ‑ Displays the trimposition of both engines. Simplifies keeping trim levels equal.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
33
NOTE: Depending on the engine type, not all screens will apply.
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
300INST M/G AVG
1.5 3.2
23477
ESTIMATED RANGE
MILES
TRIP
25MILES
42.3 MPH
STEERING ANGLE
52 PORT
6
7
8
9
10
6. Range: The estimated range is based on boat speed, fuelconsumption, and fuel remaining in the tank. The numbersdisplayed are an estimate of the distance you can travel withthe remaining fuel. Speed input required (paddle wheel, pitotpressure or GPS).
7. Fuel Economy: Displays the average "AVG" fuelconsumption as well as Instantaneous "INST" fuel economy.The numbers displayed indicate miles per gallon "M/G" orkilometers per liter "KM/L". Fuel Reset: To reset, select thedisplay screen and press "MODE/SELECT" and "‑"simultaneously.
8. Trip Odometer: Displays the distance traveled since thegauge was last reset to zero. Trip Reset: To reset, select thedisplay screen and press "MODE/SELECT" and "‑"simultaneously.
9. Digital Speedometer: Displays the boat speed in miles perhour, kilometers per hour, or nautical miles per hour. Thespeedometer will use the paddle wheel for its low speedreadings, but will switch to the speedometer or GPS (ifconnected) for high speed readings. The transition pointsetting is described in Cal 2.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
34
10.Steering Angle: Displays the relative position of the steeringsystem. Available on Mercury MerCruiser models only. Asteering angle sensor must be installed on the engine.
Speedometer Quick CAL Calibration
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
24159
SC1000 System SpeedometerThis calibration is for setting the lighting and contrast.1. Press the "MODE/SELECT" and "+" buttons simultaneously
for two seconds to bring up the "Quick Cal" display screen.2. Press the "‑" or "+" button to select the option choice displayed
in the [ ] brackets on the screen.3. Press "MODE/SELECT" to save the setting and advance
through the calibration selections.
Quick CAL
LIGHT[DOWN] [SAVE] [ UP ]
23517
Adjusts the brightness of the gauge lighting.
CONTRAST[DOWN] [SAVE] [ UP ]
23519
Adjusts the contrast of the display screen.
Speedometer CAL 1 CalibrationThis calibration turns the system display screens on and off.NOTE: Depending on the engine type, not all screens will apply.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
35
1. Press the "MODE/SELECT" and "+" buttons simultaneouslyfor approximately six seconds to bring up the "Cal 1" displayscreen.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration selections.
Remote Lighting and Contrast
[ NO ] [SAVE] [YES ]23532
REMOTE LCD LIGHT ?Adjusts the lighting levels on all gaugessimultaneously from this gauge.
[ NO ] [SAVE] [YES ]
23533
REMOTE LCD CONTRAST ? Adjusts the contrast of another SystemTachometer/Speedometer simultaneously fromthis gauge.
Time
( NO ) ( SKIP ) ( EDIT )23534
CALIBRATION 1 TIME Sets the time. Select "EDIT" to format the time
or "SKIP" to advance to the next screen.
(DOWN) (SAVE) ( UP )23535
CALIBRATION 1 TIME FORMAT 12H - M, D, Y
Formats the time as either 12 hourmonth‑day‑year or as 24 hour day‑month‑year.Select "DOWN" or "UP" to change the format.
(DOWN) (SAVE) ( UP )23536
CALIBRATION HOUR
1:42PM Adjusts the hours to match your local time.Select "DOWN" or "UP" to change the hoursetting.
(DOWN) (SAVE) ( UP )23538
CALIBRATION MINUTE
1:42PM Adjusts the minutes to match your local time.Select "DOWN" or "UP" to change the minutesetting.
Display Units
[DOWN] [SAVE] [ UP ]23539
DISPLAY UNITS
ENGLISH Changes units of measurement betweenEnglish or metric. Select "DOWN" or "UP" tochange between English or metric units.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
36
Display Units
23540
SPEED UNITS
MPH[DOWN] [SAVE] [ UP ]
Changes the units in which speed is displayed.Choose from: MPH (Miles Per Hour), KN(Knots), or KMH (Kilometers Per Hour).
Display Screens
[ NO ] [SAVE] [ YES ]23542
STEERING ANG. SCREEN ?
YESThe steering angle is displayed "YES" or off"NO". The steering angle sensor must be set to"YES" in the tachometer "CAL 2" externalsensors calibration.
23543
TEMP/CLOCK SCREEN ?
YES[ NO ] [SAVE] [ YES ]
The split screen showing air temperature andtime is displayed "YES" or off "NO".
( NO ) (SAVE) ( YES )23544
FUEL USED SCREEN ?
YES The fuel used screen is displayed "YES" or off"NO".
(SKIP) (EDIT)30164
CALIBRATION 1 FUEL USED Selects how fuel used is calibrated. Press "+" to
select "EDIT" or "SELECT" to by‑pass how thefuel used is calibrated.
[FUEL]
FUEL USED CAL : ENTER MULTIPLIER, OR REFUELED ?
[MULT]30166
Selects how fuel used is calibrated with amultiplier or with refueling. Press "‑" to selectmultiplier "MULT" or "+" to select refueling"FUEL."
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : MULTIPLIER = 1.0
30167
Adjusts multiplier between 0.50 and 1.50. Press"‑" to select "DOWN", or "+" to select "UP."
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : AMOUNT REFUELED = 0.0 G
30168
Adjust fuel used calibration using the amount offuel replaced. Press "‑" to select "DOWN", or "+"to select "UP."
( NO ) (SAVE) ( YES )23545
TRIP SCREEN
YES The trip screen is displayed "YES" or off "NO".
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
37
Display Screens
( NO ) (SAVE) ( YES )23546
FUEL MGMNT SCREEN
YES The fuel management screen is displayed"YES" or off "NO".
Simulator Mode
[ NO ] [SAVE] [ YES ]23547
SIMULATOR MODE
NO Enables the simulation mode. (Used fordemonstration purposes only.)
Exit
[ NO ] [ YES ] [CAL 2]23549
SIMULATOR MODE
EXIT ? Press "MODE/SELECT" to exit. Press "‑" to goto the start of CAL 1. Press "+" to continue to"CAL 2".
Speedometer CAL 2 CalibrationThis calibration configures the system sensor inputs.NOTE: Screens may vary depending upon the version of the gaugeand the engine type.1. Press and hold the "MODE/SELECT" and "+" buttons
simultaneously for approximately nine seconds until the "CAL2" display screen appears.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration selections.
External Sensors
(SKIP) (EDIT)23569
CALIBRATION 2 EXTERNAL SENSORS
Selects and calibrates external sensors that areinstalled in the system. Select (SKIP) to proceedto the next selection. Select (EDIT) to proceedto external sensor selection.
(SAVE) ( YES )23574
CALIBRATION 2 EXTERNAL SENSORS
( NO )AIRTEMP ? YES
Is an air temperature sensor installed? Press "‑"to select "NO" or "+" to select "YES".
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
38
External Sensors
(SAVE) ( YES )23582
CALIBRATION 2 EXTERNAL SENSORS
( NO )GPS ? YES
Is a GPS sensor installed? Press "‑" to select"NO" or "+" to select "YES".
(SAVE) ( YES )23596
CALIBRATION 2 EXTERNAL SENSORS
( NO ) USE GPS SPEED ? YES
Use the GPS input to drive the speed display?Press "‑" to select "NO" or "+" to select "YES".
(SAVE) ( UP )23592
CALIBRATION 2 SEA TEMP
(DOWN)OFFSET = 0 F
Adjust the seawater temperature sensor tocorrect display readings that are too high/low.Press "‑" or "+" to calibrate the temperaturedisplay "DOWN" or "UP".
(SAVE) ( YES )23617
CALIBRATION 2 TROLL CONTROL ?
( NO )ENABLED
To enable troll control select "YES", to disableselect "NO".
(SAVE) ( CAL1 )23618
CALIBRATION 2
( NO )EXIT ? Press "MODE/SELECT" to exit. Press "‑" to go
to the start of CAL 2. Press "+" to continue to"CAL 1".
System Tachometer Display Screens
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
23495
BREAK-IN TIME
MINLEFT65
OK OK OKBAT TMP PSI
TRIM WATER PSI
12.51.5
12.5 H20PSI
F125
1
2
3
4
5
6
TRIM 1.5
When the ignition is turned on, the tachometer will display the lastscreen that was displayed before the ignition was turned off.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
39
Press "MODE/SELECT" to change display screens. Revert backto the previous screen by pressing and holding "MODE/SELECT"for two seconds.NOTE: Readings can be displayed in English (U.S.) or metric.Refer to Tachometer Calibration.1. Engine Break-in: Displays the time remaining on the break‑in
period of a new engine. This screen will automaticallydisappear after the break‑in period is complete.
2. Quick Reference Screen: Indicates that the battery, enginetemperature, and pressures are operating properly.
3. Temperature: Displays the engine coolant temperature.4. Power Trim Angle: Displays the trim angle of the outboard or
sterndrive up to the maximum trim angle and then displays thetrailer angle. 0 = down, 10 = maximum trim, and 25 = full trailer.
5. Power Trim Angle/Water Pressure: Displays the trim angleof the engine and cooling system water pressure.
6. Water Pressure: Displays the cooling system water pressureat the engine.
NOTE: Depending on the engine type, not all screens will apply.
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
23511
OILPSI12.5
VOLTS HOURS
12.2 1.5
RPM3500
GPH USED
12.54.5FUEL
SPEED SEA TEMP
MPH 45 45 F
7
8
9
10
11
12
35 FT
7. Oil Pressure: Displays the engine oil pressure in "PSI" or"BAR".
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
40
8. Battery Voltage: Displays the voltage level (condition) of thebattery. Also records the running time of the engine.
9. Fuel Flow: Displays the engine fuel use in gallons per hour orliters per hour.
10.Digital Tachometer: Displays the engine speed in revolutionsper minute (RPM).
11.Water Depth: Displays the depth of water under thetransducer if connected. The water depth screen can beturned on or off in CAL 1 calibration. The alarm can be set totrigger whenever the boat moves into water shallower than thealarm level. Refer to CAL 2 calibration for water depth alarmand offset settings.
NOTE: A depth transducer (purchased separately) must beconnected to the system for this screen to operate.12.Speed/Temp: Displays a split screen of seawater
temperature and vessel speed.NOTE: A speed input sensor must be connected to the system forthis screen to operate.
Tachometer Quick CAL Calibration
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
30214
SC1000 System TachometerThis calibration is for setting lighting and contrast.1. Press the "MODE/SELECT" and "+" buttons simultaneously
for approximately two seconds or until the "QUICK CAL"screen appears.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
41
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration screens.
Quick CAL
LIGHT[DOWN] [SAVE] [ UP ]
23517
Adjusts the brightness of the gauge lighting.
CONTRAST[DOWN] [SAVE] [ UP ]
23519
Adjusts the contrast of the display screen.
Tachometer CAL 1 CalibrationThis calibration turns the system screens on and off.NOTE: The screens may vary depending upon the version of thegauge.1. Press and hold the "MODE/SELECT" and "+" buttons for
approximately seven seconds until the "CAL 1" screenappears.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "MODE/SELECT" to save the setting and advancethrough the calibration screens.
Tachometer CAL 1 Calibration ‑ Remote Light and Contrast
[SAVE] [ YES ]23620
REMOTE SCREENS ?
[ NO ]
If "YES" is selected, then screen changes madeon this tachometer will effect all tachometers inthe system. All tachometers need the screen setto "YES" for this function to work.
[ NO ] [SAVE] [YES ]23532
REMOTE LCD LIGHT ?Adjusts the lighting levels on all gaugessimultaneously from this gauge. If "YES" isselected, then lighting level changes made onthis tachometer will effect all tachometers in thesystem. All tachometers need the screen set to"YES" for this function to work.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
42
Tachometer CAL 1 Calibration ‑ Remote Light and Contrast
[ NO ] [SAVE] [YES ]
23533
REMOTE LCD CONTRAST ?
Adjusts the contrast of another System/SmartTow Tachometer simultaneously from thisgauge. If "YES" is selected, then contrast levelchanges made on this tachometer will effect alltachometers in the system. All tachometersneed the screen set to "YES" for this function towork.
Tachometer CAL 1 Calibration ‑ Trim
[SAVE] [ YES ]23621
HIGH RESOLUTION TRIM ?
[ NO ]
Enables the trim angle to be displayed in 0.1°increments if "YES" is selected.
[SAVE] [ YES ]23641
TRIM POPUP ?
[ NO ]
The trim display screen pops up when the trimsetting is changed if "YES" is selected.
TRIM CALIBRATIONCALIBRATION 1
[SKIP] [EDIT]23910
Select "EDIT" to calibrate the gauge to thestandard 0 ‑ 10° unit trim and 11 ‑ 25° trailerposition scale. Select "SKIP" to advance to thenext selection.
TRIM FULL DOWNCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SKIP] [SAVE]
23911
Trim the system to the full down position, thenpress the "+" button to save the setting.
TRIM FULL UPCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SKIP] [SAVE]
23912
Trim the system to the full up position, thenpress the "+" button to save the setting.
TRIM TO TRAILER POINTCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SKIP] [SAVE]
23919
Trim the system to the trailer point, then pressthe "+" button to save the setting.
Tachometer CAL 1 Calibration ‑ Display Units
[DOWN] [SAVE] [ UP ]23539
DISPLAY UNITS
ENGLISHChanges units of measure between English ormetric. Select "DOWN" or "UP" to changebetween "ENGLISH" or "METRIC" units ofmeasure.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
43
Tachometer CAL 1 Calibration ‑ Display Units
23540
SPEED UNITS
MPH[DOWN] [SAVE] [ UP ]
Changes the units in which speed is displayed.Choose from: MPH (Miles Per Hour), KN(Knots), or KMH (Kilometers Per Hour).
Tachometer CAL 1 Calibration ‑ Display Screens
QUICK REF SCREEN ?
[ NO ] [SAVE] [ YES ]23978
The quick reference screen is displayed "YES"or off "NO".
ENGINE TEMP SCREEN ?
[ NO ] [SAVE] [ YES ]23783
The engine temperature screen is displayed"YES" or off "NO".
OIL TEMP SCREEN ?
[ NO ] [SAVE] [ YES ]23786
The oil temperature screen is displayed "YES"or off "NO".
OIL PRESS SCREEN ?
[ NO ] [SAVE] [ YES ]23787
The oil pressure screen is displayed "YES" oroff "NO".
TRIM AND PSI SCREEN ?
[ NO ] [SAVE] [ YES ]23788
The split screen showing trim angle and waterpressure is displayed "YES" or off "NO".
WATER PSI SCREEN ?
[ NO ] [SAVE] [ YES ]23789
The water pressure screen is displayed "YES"or off "NO".
TRIM AND RPM SCREEN ?
[ NO ] [SAVE] [ YES ]23979
The split screen showing trim angle and engineRPM is displayed "YES" or off "NO".
RPM SCREEN ?
[ NO ] [SAVE] [ YES ]23980
The engine RPM screen is displayed "YES" oroff "NO".
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
44
Tachometer CAL 1 Calibration ‑ Display Screens
FUEL USED SCREEN ?
[ NO ] [SAVE] [ YES ]23981
The fuel used screen is displayed "YES" or off"NO".
VOLT / HOUR SCREEN ?
[ NO ] [SAVE] [ YES ]23982
The split screen showing volts and engine hoursis displayed "YES" or off "NO".
SPEED / SEA SCREEN ?
[ NO ] [SAVE] [ YES ]23983
The split screen showing speed and seatemperature is displayed "YES" or off "NO".
DEPTH SCREEN ?
[ NO ] [SAVE] [ YES ]23984
The depth screen is displayed "YES" or off"NO".
[ NO ] [SAVE] [ YES ]23547
SIMULATOR MODE
NO Enables the simulation mode. (Used fordemonstration purposes only.)
[ NO ] [ YES ] [CAL 2]23549
SIMULATOR MODE
EXIT ? Press "MODE/SELECT" to exit. Press "‑" to goto the start of CAL 1. Press "+" to continue to"CAL 2".
Tachometer CAL 2 CalibrationThis calibration configures the system sensor inputs.NOTE: The screens may vary depending upon the version of thegauge.1. Press and hold the "MODE/SELECT" and "+" buttons for
approximately ten seconds until the "CAL 2" screen appears.2. Press the "‑" or "+" button to select the option choice displayed
in the [ ] brackets on the screen.3. Press "MODE/SELECT" to save the setting and advance
through the calibration screens.FUEL TANK CALIBRATIONThere are three methods for calibrating the fuel tank levelmonitoring feature:
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
45
1. Do nothing. The linear readout is based on raw sensor values.This mode does not factor in irregular tank shapes.
2. Performing the tank calibration procedure without adding fuel;the System Tachometer/Smart Tow Tachometer will supplyan estimated range value based on linear interpolation of thesensor range values. This mode does not factor in irregulartank shapes. You must edit the tank calibration by entering anumerical value for the capacity of the fuel tank. The linearreadout is based on raw sensor values.
3. Performing the tank calibration procedure with adding fuel ateach calibration point; the System Tachometer/Smart TowTachometer will display an estimated range value that factorsin the tank shape. You must edit the tank calibration by addingfuel for 1/4, 1/2, 3/4, and full. Failure to edit the tank calibrationwill automatically default the fuel level to the liter/galloncapacity.
CAL 2 Tachometer Calibration ‑ Tank 1 and 2 Level Calibration
FUEL TANK 1 CAPACITYCALIBRATION 2
CAPACITY = 26.2 G[DOWN] [SAVE] [ UP ]
23992
Enter the capacity of the tank. Select "DOWN"or "UP" to set the tank capacity. Then press"SAVE". This option is the same for tank 1 as itis for tank 2.
FUEL TANK 1CALIBRATION 2
[SKIP] [EDIT]23993
Select "EDIT" to enter the calibration mode ofthe fuel tank. The calibration procedure is thesame for tank 1 as it is for tank 2. Select "EDIT"to begin tank level calibration.
DEFAULT CALIBRATION,TANK CALIBRATION :
OR ADD FUEL ?[DFLT] [ADD ]
23994
Select "DFLT" to let SmartCraft calibrate thetank levels. Select "ADD" to calibrate the tanklevels by adding fluid to the tank.
EMPTY TANKCALIBRATING :
THEN PRESS PLUS BUTTON[SKIP] [SAVE]
23995
Empty the tank. Select "SAVE" to calibrate thetank level to empty.
FILL TANK TO 1/4
THEN PRESS PLUS BUTTON[SAVE]
30427
Fill the tank to 1/4 full. Select "SAVE" to calibratethe tank level to 1/4 full.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
46
CAL 2 Tachometer Calibration ‑ Tank 1 and 2 Level Calibration
FILL TANK TO ½
THEN PRESS PLUS BUTTON[SAVE]
30428
Fill the tank to 1/2 full. Select "SAVE" to calibratethe tank level to 1/2 full.
FILL TANK TO 3/4
THEN PRESS PLUS BUTTON[SAVE]
30429
Fill the tank to 3/4 full. Select "SAVE" to calibratethe tank level to 3/4 full.
FILL TANK TO FULL
THEN PRESS PLUS BUTTON[SAVE]
30430
Fill the tank to full. Select "SAVE" to calibratethe tank level to full.
TANK 2 INPUTOIL TANK
CALIBRATION 2
[SAVE][DOWN] [ UP ]24148
Select tank 2 input: oil tank, fuel tank 2, watertank, waste tank, or not installed.
EXTERNAL SENSORS
CAL 2 Tachometer Calibration ‑ External Sensors
EXTERNAL SENSORS ?CALIBRATION 2
[SKIP] [EDIT]24006
Selects and calibrates external sensors that areinstalled in the system. Select "SKIP" to proceedto the speed options. Select "EDIT" to proceedto external sensor selection.
EXTERNAL SENSORSCALIBRATION 2
PITOT SENSOR ? YES[ NO ] [SAVE] [YES ]
24007
Is the boat equipped with a pitot sensor tomeasure boat speed? Press "‑" to select "NO"or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
PADDLE SENSOR ? YES[ NO ] [SAVE] [YES ]
24008
Is the boat equipped with a paddle wheel tomeasure boat speed? Press "‑" to select "NO"or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
TRIM SENSOR ? YES[ NO ] [SAVE] [YES ]
24009
Is the boat equipped with a trim sensor? Press"‑" to select "NO" or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
SEA TEMP ?[ NO ] [SAVE] [YES ]
24010
YESIs the boat equipped with a seawatertemperature sensor? Press "‑" to select "NO" or"+" to select "YES".
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
47
CAL 2 Tachometer Calibration ‑ External Sensors
EXTERNAL SENSORSCALIBRATION 2
STEERING SENSOR ?[ NO ] [SAVE] [YES ]
24011
YES Is the boat equipped with a steering sensor?Press "‑" to select "NO" or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
INVERT STEERING ?[ NO ] [SAVE] [YES ]
30432
YESChanges the position (direction) of the steeringdisplay. Press "‑" to select "NO" or "+" to select"YES".
SPEED OPTIONCALIBRATION 2
[SKIP] [EDIT]24012
This section configures the following speedsensors. Select "EDIT" to calibrate the sensors.Select "SKIP" to proceed to the depth sensorscreen.
PITOT SENSOR100 PSI TYPE
CALIBRATION 2
[ NO ] [SAVE] [YES ]24014
Select pitot transducer type. Choose between100 or 200 psi. (100 psi is the most common.)
PITOT SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24018
MULTIPLIER = 1.00
Adjust the pitot pressure sensor to correctdisplay readings that are too high/low. Press "‑"or "+" to calibrate the pitot sensor multiplier"DOWN" or "UP".
PADDLE SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24021
PULSEFACTOR = 3.0
Adjust paddle wheel frequency to correctdisplay readings that are too high/low. Press "‑"or "+" to calibrate the paddle sensor pulse factor"DOWN" or "UP".
TRANSITION SPEEDCALIBRATION 2
[DOWN] [SAVE] [ UP ]24022
TRANSITION = 30 MPH
Set the speed at which the gauge stops readingthe paddle wheel and starts using pitot sensorto measure boat speed. Press "‑" or "+" tocalibrate the transition speed "DOWN" or "UP".
DEPTH SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24023
OFFSET = 3 FEET
Electronically configure a depth offset. Enteringa negative number gives you a waterline offset.A positive number gives you a keel offset. Press"‑" or "+" to calibrate the depth sensor offset"DOWN" or "UP".
DEPTH ALARMCALIBRATION 2
[DOWN] [SAVE] [ UP ]24024
LEVEL = 2.5 FEET
Enter a depth value. When the depth transducerreads that value or below, the shallow wateralarm will sound. Press "‑" or "+" to calibrate thedepth alarm level "DOWN" or "UP".
[ NO ] [ YES ] [CAL 1]24025
CALIBRATION 2
EXIT ? Press "MODE/SELECT" to exit. Press "‑" to goto the start of CAL 2. Press "+" to continue to"CAL 1."
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
48
Troll Control OperationNOTE: The troll control feature is only available on the SystemTachometer and Speedometer.
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLLMODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
a a
Troll Speed On
10.5 ACTMPH 12.0
PUSH SELECT TO DISENGAGE
SETMPH
feTroll Speed On
1000 ACTRPM 1500
PUSH SELECT TO DISENGAGE
SETRPM
dc
FAIR
FSEA70 62
10:35TR
b b
30350
a - Increase troll speedb - Decrease troll speedc - Actual RPM
d - Set RPMe - Actual MPHf - Set MPH
NOTE: Troll control may not be available on all engine models.NOTE: The troll control minimum and maximum range may changedepending on engine type.Set the troll control by using the System Tachometer orSpeedometer. The speedometer will set the speed in MPH, KPH,or KN, while the tachometer will set the speed in RPM.The troll control can be shut off at anytime by adjusting the throttleor by pushing the "MODE/SELECT" button when in the troll displayscreen.When the troll control is shut off, the system will remember the setspeed. When the troll control is engaged, it will return to the setspeed.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
49
The display screen will revert back to the previous screen after fiveseconds of inactivity. Push the "+" or "‑" button to reactivate thetroll control display screen.When the troll control is engaged and not in the troll control displayscreen, a flashing "TR" signal will appear in the upper left cornerof the screen to indicate the troll control is still active.SETTING TROLL CONTROL
MODE
RPM x 1000
0
23 4
5
6
7
1
RESET
TROLL+
TROLL-
SPEED
0
2030 40
50
60
70
10
RESET
TROLL- MODE +
TROLL
600575PUSH SELECT TO DISENGAGE
TROLL SPEED ON OFFACTRPM
SETRPM
TROLL SPEED ON OFF
PUSH SELECT TO DISENGAGE
3.02.5 ACTMPH
SETMPH
SETMPH
TROLL SPEED TOO FAST
REDUCE TROLL SPEED
7.54.5 ACTMPH
SETMPH
TROLL SPEED TOO SLOW
INCREASE TROLL SPEED
3.02.5 ACTMPH
c d 23035
a afe
b b
a - Increase troll set speedb - Decrease troll set speedc - Setting is too fast, reduce set troll speedd - Setting is too slow, increase set troll speede - Actual speedf - Set speed
1. With the engine running, shift the engine into gear. Set theengine speed at idle.
2. Push in either the "+" or "‑" buttons to bring up the troll controldisplay screen.
3. Press "MODE/SELECT" to engage the troll control.
SYSTEM TACH/SPEED DESCRIPTIVE TEXT
50
4. Use the "+" and "‑" buttons to set the desired speed. Use "+"to increase the set speed and use "‑" to decrease the setspeed.
5. If the troll speed is set to a higher speed than the troll controlcan maintain, the "TROLL SPEED TOO FAST" display willappear. Reduce the set troll speed.
6. If the troll speed is set to a slower speed than the troll controlcan maintain, the "TROLL SPEED TOO SLOW" display willappear. Increase the set troll speed.
CANCELING TROLL CONTROLThere are three ways to cancel the troll control:• Press the "MODE/SELECT" button when in the troll display
screen.• Move the throttle to a different speed.• Shift the engine into neutral.
SMART TOW TACH/SPEED GPS
51
Basic Operation and FeaturesNOTE: Descriptive text alarm warning screens are displayed withGen I (2007) engines and newer.
30139SELECT
0
23 4
5
6
7
1
RESET
RPM x 1000
SMART TOW
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
Smart Tow Speedometer withGPS
Smart Tow Tachometer
Power up: Each gauge will power up when the ignition is turnedon. The gauges will stay on as long as the ignition is on.Lights: Adjusts the brightness and contrast of the gauge.Buttons: The "SELECT" button is used for selecting informationscreens. The "+" and "‑" buttons are used for setting engine speedfor cruise control, launch control, and setting gauge calibrations.Cruise control: Sets and controls the speed of the engine forcruising on Smart Tow Tachometer and Speedometer.Launch control: Sets and controls the speed of acceleration fromidle to set cruise speed for Smart Tow Tachometer andSpeedometer.Engine Guardian System: Monitors the critical sensors on theengine for any early indication of problems. The system willrespond to a problem by reducing engine speed and alerting theoperator to a potentially damaging situation.Warning system: The system sounds the warning horn anddisplays the warning with descriptive text.IMPORTANT: Optional sensors such as depth, fuel, paddle wheel,and steering angle, should always be connected to the starboardengine when using SmartCraft gauges version 4.0 or later.
SMART TOW TACH/SPEED GPS
52
Automatic Engine Detection FeatureIMPORTANT: Multiple engine applications using only one SmartTow Tachometer, must have the Smart Tow Tachometerconnected to the starboard engine. Multiple Smart TowTachometer applications must have the Smart Tow Tachometersprogramed for their specific engine location manually or throughthe automatic engine detection feature.The System Tachometer/Speedometer has an automatic enginedetection feature. This feature automatically detects which enginetype is used and configures the gauge to match that engine type.The first power up of the gauge, or after a Master Reset, the gaugewill display "AUTODETECT". Press the "MODE/SELECT" buttonto start the automatic engine detection feature and the gauge willdetermine the engine type. This will preset the data monitoringscreens to make the initial setup easier.
AUTODETECTENGINE SMARTSCREEN
PRESS MODE/SELECT TO START24298
If the gauge shows a warning of "NO STARBOARD ENGINE" or"MULTIPLE STARBOARD ENGINES", the engine location (portand starboard) must be selected by an authorized dealer equippedwith the computer diagnostic system (CDS) tool.
Master ResetReturns the gauge to the factory defaults through the Master Resetcommand.IMPORTANT: Performing a Master Reset will reset the unit to thefactory defaults, thus eliminating any installation and calibrationsperformed during set up of product.
SMART TOW TACH/SPEED GPS
53
Press the "‑" and "+" buttons simultaneously for approximately 10seconds (until the graphic bars collide) to restore the unit to factorydefault settings. Press the "MODE/SELECT" button to confirm.
22660
MASTERRESET
MASTERRESETERASE CALIBRATION !
PRESS MODE/SELECT TO CONFIRM
Alarm Warnings with Descriptive TextNOTE: Descriptive text alarm warning screens are displayed withGen I (2007) engines and newer.
30139SELECT
0
23 4
5
6
7
1
RESET
RPM x 1000
SMART TOW
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
Smart Tow Speedometer withGPS
Smart Tow Tachometer
When a problem is detected, the "SYS FAULT" alarm appears onthe display. Press the "+" button to show the faulty component. Theupper bar in this screen displays the system where the fault islocated. The faulty component is described in the scrolling text.Press the "+" button for more information. This screen gives adetailed description of the fault in the scrolling text. Press the "+"button to view the required corrective action.The alarm message will stay displayed until the "‑" button ispressed. If there are multiple alarms, press the "SELECT" buttonto display.
SMART TOW TACH/SPEED GPS
54
If a problem can cause immediate engine damage, the EngineGuardian System will respond to the problem by limiting enginepower. Immediately reduce the throttle speed to idle and refer tothe warning messages on the following pages. Refer to theappropriate service manual for further explanation of the problemand the correct action to take.If the "SELECT" button is pressed to display a different screen, theflashing alarm signal "AL" will appear in the upper right corner toindicate there still is a problem.
Alarm Warning with Descriptive Text
[ SHOW ]
SYS FAULT
24184
The "SYS FAULT" bar indicates there is aproblem in the system. "SHOW" displaysthe faulty component.
[ MORE ][ NEXT ][ EXIT ]
STBD SYSTEM FAULT
<FAULTY COMPONENT>
24186
STBD SYSTEM FAULT The top bar indicates the system with thefaulty component. The scrolling textdisplays the faulty component. "NEXT"displays the next fault. "MORE" displays adetailed description of the fault.
[ ACTION ][ NEXT ][ EXIT ]
STBD SYSTEM FAULT
<FAULT DESCRIPTION>
24187
The scrolling text explains in detail thedescription of the fault. "ACTION" displaysthe course of action required by theoperator.
[ BACK ][ NEXT ][ EXIT ]
STBD SYSTEM FAULT
<CORRECTIVE ACTION>
24189
The scrolling text displays the course ofaction required by the operator.
SMART TOW TACH/SPEED GPS
55
Display ScreensTachometer Display Screen Speedometer Display Screen
Engine Break‑in (2‑Stroke outboard only) SpeedEngine Temperature Fuel UsedOil Temperature Cog/Sog ‑ If there is a GPS inputOil PSI Distance and Fuel to WaypointTrim and RPM Clock ‑ Air/Sea TempTrim and Water Pressure Instant and Average Fuel EconomyWater Pressure Trip OdometerBattery Voltage and Engine Hours Fuel Tank LevelsFuel Flow and Fuel Used Oil Tank LevelsSpeed and Sea Temperature Fresh Water LevelsBattery Voltage Waste Water levels% Fuel Remaining (Fuel Tank 1) Steering Angle (MerCruiser only)DepthTrim Position Dual Engine
Fuel PSI Trim and RPM SynchronizerTrailer and RPMRPMQuick Reverence ScreenBattery, Temperature, PSI
SMART TOW TACH/SPEED GPS
56
Smart Tow Speedometer with GPS Display ScreensNOTE: Depending on the engine type, not all screens will apply.
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
5:30 PM
70 60 FAIR
FSEA
1
2
3
4
TRIP
25 MILES
INST M/G AVG
1.5 3.2
42.3 MPH
3035430.9FUEL USED
GAL
COG MPH- - - - - -
5
6
When the ignition is turned on, the speedometer will show the lastscreen that was displayed before the ignition was turned off.Press "SELECT" to change display screens. Revert back to theprevious screen by pressing and holding "SELECT" for twoseconds.NOTE: Readings can be displayed in English (U.S.) or metric.Refer to Smart Tow Speedometer with GPS CAL 1Calibration.NOTE: The descriptions may not be in order on the gauge. Theorder may change depending on engine type.1. Clock - Temp: Clock, air temperature, and water temperature.
The air and water temperature sensors must be connected toobtain display readings.
2. Fuel Economy: Displays the average "AVG" fuelconsumption and instantaneous "INST" fuel economy. Thenumbers displayed indicate miles per gallon "M/G" orkilometers per liter "KM/L". Fuel Reset: To reset, select thedisplay screen and press "SELECT" and "‑" simultaneously.
SMART TOW TACH/SPEED GPS
57
3. Trip Odometer: Displays the distance traveled since thegauge was last reset to zero. Trip Reset: To reset, select thedisplay screen and press "SELECT" and "‑" simultaneously.
4. Digital Speedometer: Displays the boat speed in miles perhour, kilometers per hour, or nautical miles per hour. Thespeedometer will use the paddle wheel for its low speedreadings and will switch to the pitot pressure or GPS (ifconnected) for high speed readings. The transition pointsetting is described in Cal 2.
5. Fuel Used: Displays the amount of fuel used. This isdetermined by the PCM.
6. Course Over Ground (COG): Displays the direction of traveland current speed through a GPS.
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
7
30356
STEERING ANGLE
52 PORT
8
TO WAYPOINT
OIL
E FGALLONS0.6
FUEL
E FGALLONS60
RPM SYNCH
STBDPORT
TRIM SYNCH
STBDPORT
10
11
12
9
300ESTIMATED RANGE
MILES
13
- - - - - - GAL MIDIST
7. To Waypoint: Displays the amount of fuel to the waypoint andthe distance to the waypoint. A GPS unit with waypointscapability must be installed to display the distance to thewaypoint.
8. Fuel Level: Displays the amount of fuel remaining.
SMART TOW TACH/SPEED GPS
58
9. Oil Level: Displays the amount of engine oil remaining(2‑Stroke outboard only), or water/waste tank level or secondfuel tank.
10.Steering Angle: Displays the relative position of the steeringsystem. Available on Mercury MerCruiser models only. Asteering angle sensor must be installed on the engine.
11.Range: The estimated range is based on boat speed, fuelconsumption, and fuel remaining in the tank. The numbersdisplayed are an estimate of the distance you can travel withthe remaining fuel. Speed input is required from the paddlewheel, pitot pressure, or GPS.
12.RPM Synchronizer: Dual engines only ‑ Monitors therevolutions of both engines.
13.Trim Synchronizer: Dual engines only ‑ Displays the trimposition of both engines. Simplifies keeping trim levels equal.
Smart Tow Speedometer with GPS Quick CALCalibration
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
30163
Smart Tow Speedometer with GPSThis calibration is for setting the lighting and contrast.1. Press the "SELECT" and "+" buttons simultaneously for two
seconds to bring up the "Quick Cal" display screen.2. Press the "‑" or "+" button to select the option choice displayed
in the [ ] brackets on the screen.3. Press "SELECT" to save the setting and advance through the
calibration selections.
SMART TOW TACH/SPEED GPS
59
Quick CAL
LIGHT[DOWN] [SAVE] [ UP ]
23517
Adjusts the brightness of the gauge lighting.
CONTRAST[DOWN] [SAVE] [ UP ]
23519
Adjusts the contrast of the display screen.
Smart Tow Speedometer with GPS CAL 1CalibrationThis calibration turns on and off the system display screens.NOTE: Depending on the engine type, not all screens will apply.1. Press the "SELECT" and "+" buttons simultaneously for
approximately six seconds to bring up the "Cal 1" displayscreen.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "SELECT" to save the setting and advance through thecalibration selections.
Remote Lighting and Contrast
[ NO ] [SAVE] [YES ]23532
REMOTE LCD LIGHT ?Adjusts the lighting levels on all gaugessimultaneously from this gauge.
[ NO ] [SAVE] [YES ]
23533
REMOTE LCD CONTRAST ? Adjusts the contrast of another SystemTachometer/Speedometer simultaneously fromthis gauge.
Time
( NO ) ( SKIP ) ( EDIT )23534
CALIBRATION 1 TIME Sets the time. Select "EDIT" to format the time
or "SKIP" to advance to the next screen.
SMART TOW TACH/SPEED GPS
60
Time
(DOWN) (SAVE) ( UP )23535
CALIBRATION 1 TIME FORMAT 12H - M, D, Y
Formats the time as either 12 hourmonth‑day‑year or as 24 hour day‑month‑year.Select "DOWN" or "UP" to change the format.
[ NO ] [SAVE] [YES ]
CALIBRATION 1 USE GPS TIME ENABLED
30172
Enables or disables time displayed through theGPS. Press "‑" to select "NO", or "+" to select"YES."
[DOWN] [SAVE] [ UP ]
CALIBRATION 1 UTC ZONEUTC CORRECTION = 0 H
30197
Changes the UTC zone corrections from ‑13 Hto 13 H. Press "‑" to select "DOWN", or "+" toselect "UP."
(DOWN) (SAVE) ( UP )23536
CALIBRATION HOUR
1:42PM Adjusts the hours to match your local time.Select "DOWN" or "UP" to change the hoursetting.
(DOWN) (SAVE) ( UP )23538
CALIBRATION MINUTE
1:42PM Adjusts the minutes to match your local time.Select "DOWN" or "UP" to change the minutesetting.
Display Units
[DOWN] [SAVE] [ UP ]23539
DISPLAY UNITS
ENGLISH Changes units of measurement betweenEnglish or metric. Select "DOWN" or "UP" tochange between English or metric units.
23540
SPEED UNITS
MPH[DOWN] [SAVE] [ UP ]
Changes the units in which speed is displayed.Choose from: MPH (Miles Per Hour), KN(Knots), or KMH (Kilometers Per Hour).
Waypoint Display
( NO ) (SAVE) ( YES )30202
TO WAYPOINT SCREEN ?
YES Activates or disables the "TO WAYPOINT"screen. Press "‑" to select "NO", or "+" to select"YES."
( NO ) (SAVE) ( YES )30203
WAYPOINT ALARM ?
YES Activates or disables the "WAYPOINT ALARM."Press "‑" to select "NO", or "+" to select "YES."
SMART TOW TACH/SPEED GPS
61
Waypoint Display
(DOWN) (SAVE) ( UP )30198
WAYPOINT ALARM
DISTANCE = 0.3 MILESSets the distance from the waypoint when thealarm will be activated. Press "‑" to select"DOWN", or "+" to select "UP."
Display Screens
[ NO ] [SAVE] [ YES ]23542
STEERING ANG. SCREEN ?
YESThe steering angle is displayed "YES" or off"NO". The steering angle sensor must be set to"YES" in the tachometer "CAL 2" externalsensors calibration.
23543
TEMP/CLOCK SCREEN ?
YES[ NO ] [SAVE] [ YES ]
The split screen showing air temperature andtime is displayed "YES" or off "NO".
( NO ) (SAVE) ( YES )23544
FUEL USED SCREEN ?
YES The fuel used screen is displayed "YES" or off"NO".
(SKIP) (EDIT)30164
CALIBRATION 1 FUEL USED Selects how fuel used is calibrated. Press "+" to
select "EDIT" or "SELECT" to by‑pass how thefuel used is calibrated.
[FUEL]
FUEL USED CAL : ENTER MULTIPLIER, OR REFUELED ?
[MULT]30166
Selects how fuel used is calibrated with amultiplier or with refueling. Press "‑" to selectmultiplier "MULT" or "+" to select refueling"FUEL."
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : MULTIPLIER = 1.0
30167
Adjusts multiplier between 0.50 and 1.50. Press"‑" to select "DOWN", or "+" to select "UP."
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : AMOUNT REFUELED = 0.0 G
30168
Adjusts fuel used calibration using the amountof fuel replaced. Press "‑" to select "DOWN", or"+" to select "UP."
( NO ) (SAVE) ( YES )23545
TRIP SCREEN
YES The trip screen is displayed "YES" or off "NO".
( NO ) (SAVE) ( YES )23546
FUEL MGMNT SCREEN
YES The fuel management screen is displayed"YES" or off "NO".
SMART TOW TACH/SPEED GPS
62
Simulator Mode
[ NO ] [SAVE] [ YES ]23547
SIMULATOR MODE
NO Enables the simulation mode. (Used fordemonstration purposes only.)
Exit
[ NO ] [ YES ] [CAL 2]23549
SIMULATOR MODE
EXIT ? Press "SELECT" to exit. Press "‑" to go to thestart of CAL 1. Press "+" to continue to "CAL 2."
Smart Tow Speedometer with GPS CAL 2CalibrationThis calibration configures the system sensor inputs.NOTE: Screens may vary depending on the version of the gaugeand engine type.1. Press and hold the "SELECT" and "+" buttons simultaneously
for approximately nine seconds until the "CAL 2" displayscreen appears.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "SELECT" to save the setting and advance through thecalibration selections.
External Sensors
(SKIP) (EDIT)23569
CALIBRATION 2 EXTERNAL SENSORS
Selects and calibrates external sensors that areinstalled in the system. Select [SKIP] to proceedto the next selection. Select [EDIT] to proceedto external sensor selection.
(SAVE) ( YES )23574
CALIBRATION 2 EXTERNAL SENSORS
( NO )AIRTEMP ? YES
Is an air temperature sensor installed? Press "‑"to select "NO" or "+" to select "YES".
(SAVE) ( YES )23582
CALIBRATION 2 EXTERNAL SENSORS
( NO )GPS ? YES
Is a GPS sensor installed? Press "‑" to select"NO" or "+" to select "YES".
SMART TOW TACH/SPEED GPS
63
External Sensors
(SAVE) ( YES )23596
CALIBRATION 2 EXTERNAL SENSORS
( NO ) USE GPS SPEED ? YES
Use the GPS input to drive the speed display?Press "‑" to select "NO" or "+" to select "YES".
(SAVE) ( UP )23592
CALIBRATION 2 SEA TEMP
(DOWN)OFFSET = 0 F
Adjust the seawater temperature sensor tocorrect display readings that are too high/low.Press "‑" or "+" to calibrate the temperatedisplay "DOWN" or "UP".
(SAVE) ( CAL1 )23618
CALIBRATION 2
( NO )EXIT ? Press "SELECT" to exit. Press "‑" to go to the
start of CAL 2. Press "+" to continue to "CAL 1."
Smart Tow Tachometer Display ScreensNOTE: Depending on the engine type, not all screens will apply.
SELECT
0
23 4
5
6
7
1
RESET
RPM x 1000
SMART TOW
BREAK-IN TIME
MINLEFT65
OK OK OKBAT TMP PSI
F125
1
2
3
4
5
6TRIM RPM
19001.5
COLD75 F
HOT
OIL
OILPSI12.5
30406
When the ignition is turned on, the tachometer will display the lastscreen that was displayed before the ignition was turned off.Press "SELECT" to change display screens. Revert back to theprevious screen by pressing and holding "SELECT" for twoseconds.NOTE: Readings can be displayed in English (U.S.) or metric.Refer to Smart Tow Tachometer Cal 1 Calibration.1. Quick Reference Screen: Indicates that the battery, engine
temperature, and pressures are operating properly.
SMART TOW TACH/SPEED GPS
64
2. Engine Break-in: Displays the time remaining on the break‑inperiod of a new engine. This screen will automaticallydisappear after the break‑in period is complete.
3. Temperature: Displays the engine coolant temperature.4. Oil Temperature: Displays the engine oil temperature.5. Oil Pressure: Displays the engine oil pressure in "PSI" or
"BAR".6. Trim Position/RPM: Displays the trim angle of the outboard
or sterndrive up to the maximum trim angle and the engineRPM.
SELECT
0
23 4
5
6
7
1
RESET
RPM x 1000
SMART TOW
TRAILER RPM
190025
TRIM WATER PSI
12.51.5
12.5 H20PSI
VOLTS HOURS
12.2 1.5GPH USED
12.54.5FUEL
RPM3500
7
8
9
10
11
12 30418
7. Trim Position/Water Pressure: Displays the trim angle of theengine or drive system and cooling system water pressure.
8. Trailer Position/RPM: Displays the trailer position and theengine RPM.
9. Water Pressure: Displays the cooling system water pressureat the engine.
10.Battery Voltage/Engine Run Time: Displays the batteryvoltage level and the running time of the engine.
11.Fuel Flow: Displays the engine fuel use per hour and totalamount of fuel used.
SMART TOW TACH/SPEED GPS
65
12.Digital Tachometer: Displays the engine speed in revolutionsper minute (RPM).
SELECT
0
23 4
5
6
7
1
RESET
RPM x 1000
SMART TOW
V12.3TRIM 5
5 %
13
14
35 FTSPEED SEA TEMP
MPH 45 45 F
50.7 FUELPSI
30420
15
16
17
18
13.Water Depth: Displays the depth of water under thetransducer if connected. The water depth screen can beturned on or off in CAL 1 calibration. The alarm can be set totrigger whenever the boat moves into water shallower than thealarm level. Refer to CAL 2 calibration for water depth alarmand offset settings.
NOTE: A depth transducer (purchased separately) must beconnected to the system for this screen to operate.14.Speed/Temp: Displays a split screen of seawater
temperature and vessel speed.NOTE: A speed input sensor (purchased separately) must beconnected to the system for this screen to operate.15.Battery Voltage: Displays the battery voltage level.16.Trim Position: Displays the trim angle of the engine or drive
system.17.Fuel Percentage: Displays the estimated amount of fuel
remaining.18.Fuel Pressure: Displays the pressure of the fuel.
SMART TOW TACH/SPEED GPS
66
Smart Tow Tachometer Quick CAL Calibration
30215SELECT
0
23 4
5
6
7
1
RESET
RPM x 1000
SMART TOW
Smart Tow TachometerThis calibration is for setting lighting and contrast.1. Press the "SELECT" and "+" buttons simultaneously for
approximately two seconds or until the "QUICK CAL" screenappears.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "SELECT" to save the setting and advance through thecalibration screens.
Quick CAL
LIGHT[DOWN] [SAVE] [ UP ]
23517
Adjusts the brightness of the gauge lighting.
CONTRAST[DOWN] [SAVE] [ UP ]
23519
Adjusts the contrast of the display screen.
Smart Tow Tachometer CAL 1 CalibrationThis calibration turns the system screens on and off.NOTE: The screens may vary depending upon the version of thegauge.
SMART TOW TACH/SPEED GPS
67
1. Press and hold the "SELECT" and "+" buttons forapproximately seven seconds until the "CAL 1" screenappears.
2. Press the "‑" or "+" button to select the option choice displayedin the [ ] brackets on the screen.
3. Press "SELECT" to save the setting and advance through thecalibration screens.
Tachometer CAL 1 Calibration ‑ Remote Light and Contrast
[SAVE] [ YES ]23620
REMOTE SCREENS ?
[ NO ]
If "YES" is selected, then screen changes madeon this tachometer will effect all tachometers inthe system. All tachometers need the screen setto "YES" for this function to work.
[ NO ] [SAVE] [YES ]23532
REMOTE LCD LIGHT ?Adjusts the lighting levels on all gaugessimultaneously from this gauge. If "YES" isselected, then lighting level changes made onthis tachometer will effect all tachometers in thesystem. All tachometers need the screen set to"YES" for this function to work.
[ NO ] [SAVE] [YES ]
23533
REMOTE LCD CONTRAST ?
Adjusts the contrast of another System/SmartTow Tachometer simultaneously from thisgauge. If "YES" is selected, then contrast levelchanges made on this tachometer will effect alltachometers in the system. All tachometersneed the screen set to "YES" for this function towork.
Tachometer CAL 1 Calibration ‑ Trim
[SAVE] [ YES ]23621
HIGH RESOLUTION TRIM ?
[ NO ]
Enables the trim angle to be displayed in 0.1°increments if "YES" is selected.
[SAVE] [ YES ]23641
TRIM POPUP ?
[ NO ]
The trim display screen pops up when the trimsetting is changed if "YES" is selected.
TRIM CALIBRATIONCALIBRATION 1
[SKIP] [EDIT]23910
Select "EDIT" to calibrate the gauge to thestandard 0 ‑ 10° unit trim and 11 ‑ 25° trailerposition scale. Select "SKIP" to advance to thenext selection.
SMART TOW TACH/SPEED GPS
68
Tachometer CAL 1 Calibration ‑ Trim
TRIM FULL DOWNCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SKIP] [SAVE]
23911
Trim the system to the full down position, thenpress the "+" button to save the setting.
TRIM FULL UPCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SAVE]
30217
Trim the system to the full up position, thenpress the "+" button to save the setting.
TRIM TO TRAILER POINTCALIBRATION 1
THEN PRESS PLUS BUTTON[DFLT] [SAVE]
30219
Trim the system to the trailer point, then pressthe "+" button to save the setting.
Tachometer CAL 1 Calibration ‑ Display Units
[DOWN] [SAVE] [ UP ]23539
DISPLAY UNITS
ENGLISHChanges units of measure between English ormetric. Select "DOWN" or "UP" to changebetween "ENGLISH" or "METRIC" units ofmeasure.
23540
SPEED UNITS
MPH[DOWN] [SAVE] [ UP ]
Changes the units in which speed is displayed.Choose from: MPH (Miles Per Hour), KN(Knots), or KMH (Kilometers Per Hour).
Tachometer CAL 1 Calibration ‑ Display Screens
QUICK REF SCREEN ?
[ NO ] [SAVE] [ YES ]23978
The quick reference screen is displayed "YES"or off "NO".
ENGINE TEMP SCREEN ?
[ NO ] [SAVE] [ YES ]23783
The engine temperature screen is displayed"YES" or off "NO".
OIL TEMP SCREEN ?
[ NO ] [SAVE] [ YES ]23786
The oil temperature screen is displayed "YES"or off "NO".
OIL PRESS SCREEN ?
[ NO ] [SAVE] [ YES ]23787
The oil pressure screen is displayed "YES" oroff "NO".
SMART TOW TACH/SPEED GPS
69
Tachometer CAL 1 Calibration ‑ Display Screens
TRIM AND PSI SCREEN ?
[ NO ] [SAVE] [ YES ]23788
The split screen showing trim angle and waterpressure is displayed "YES" or off "NO".
WATER PSI SCREEN ?
[ NO ] [SAVE] [ YES ]23789
The water pressure screen is displayed "YES"or off "NO".
TRIM AND RPM SCREEN ?
[ NO ] [SAVE] [ YES ]23979
The split screen showing trim angle and engineRPM is displayed "YES" or off "NO".
RPM SCREEN ?
[ NO ] [SAVE] [ YES ]23980
The engine RPM screen is displayed "YES" oroff "NO".
FUEL USED SCREEN ?
[ NO ] [SAVE] [ YES ]23981
The fuel used screen is displayed "YES" or off"NO".
FUEL USEDCALIBRATION 1
[SKIP] [EDIT]30221
Adjusts the calculation for determining fuel usedbased on the size of the fuel tank.
[FUEL]
FUEL USED CAL : ENTER MULTIPLIER, OR REFUELED ?
[MULT]30166
Selects how fuel used is calculated with amultiplier or with refueling.
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : MULTIPLIER = 1.0
30167
Adjusts multiplier between 0.50 and 1.50.
[DOWN] [SAVE] [ UP ]
FUEL USED CAL : AMOUNT REFUELED = 0.0 G
30168
Adjusts fuel used calibration using the amountof fuel replaced.
FUEL PSI SCREEN ?
[ NO ] [SAVE] [ YES ]30653
Fuel pressure is displayed "YES" or off "NO".
SMART TOW TACH/SPEED GPS
70
Tachometer CAL 1 Calibration ‑ Display Screens
VOLT / HOUR SCREEN ?
[ NO ] [SAVE] [ YES ]23982
The split screen showing volts and engine hoursis displayed "YES" or off "NO".
SPEED / SEA SCREEN ?
[ NO ] [SAVE] [ YES ]23983
The split screen showing speed and seawatertemperature is displayed "YES" or off "NO".
(SAVE) ( UP )30654
SEA TEMP
(DOWN)OFFSET = 0 F
Adjusts the temperature difference betweensensor and what the gauge displays.
DEPTH SCREEN ?
[ NO ] [SAVE] [ YES ]23984
The depth screen is displayed "YES" or off"NO".
[ NO ] [SAVE] [ YES ]23547
SIMULATOR MODE
NO Enables the simulation mode. (Used fordemonstration purposes only.)
[ NO ] [ YES ] [CAL 2]23549
SIMULATOR MODE
EXIT ? Press "SELECT" to exit. Press "‑" to go to thestart of CAL 1. Press "+" to continue to "CAL 2".
Smart Tow Tachometer CAL 2 CalibrationThis calibration configures the system sensor inputs.NOTE: The screens may vary depending upon the version of thegauge.1. Press and hold the "SELECT" and "+" buttons for
approximately ten seconds until the "CAL 2" screen appears.2. Press the "‑" or "+" button to select the option choice displayed
in the [ ] brackets on the screen.3. Press "SELECT" to save the setting and advance through the
calibration screens.FUEL TANK CALIBRATIONThere are three methods for calibrating the fuel tank levelmonitoring feature:
SMART TOW TACH/SPEED GPS
71
1. Do nothing. The linear readout is based on raw sensor values.This mode does not factor in irregular tank shapes.
2. Performing the tank calibration procedure without adding fuel;the System Tachometer/Smart Tow Tachometer will supplyan estimated range value based on linear interpolation of thesensor range values. This mode does not factor in irregulartank shapes. You must edit the tank calibration by entering anumerical value for the capacity of the fuel tank. The linearreadout is based on raw sensor values.
3. Performing the tank calibration procedure with adding fuel ateach calibration point; the System Tachometer/Smart TowTachometer will display an estimated range value that factorsin the tank shape. You must edit the tank calibration by addingfuel for 1/4, 1/2, 3/4, and full. Failure to edit the tank calibrationwill automatically default the fuel level to the liter/galloncapacity and will not factor in irregular tank shapes.
CAL 2 Tachometer Calibration ‑ Tank 1 and 2 Level Calibration
FUEL TANK 1 CAPACITYCALIBRATION 2
CAPACITY = 26.2 G[DOWN] [SAVE] [ UP ]
23992
Enter the capacity of the tank. Select "DOWN"or "UP" to set the tank capacity. Then press"SAVE". This option is the same for tank 1 as itis for tank 2.
FUEL TANK 1CALIBRATION 2
[SKIP] [EDIT]23993
Select "EDIT" to enter the calibration mode ofthe fuel tank. The calibration procedure is thesame for tank 1 as it is for tank 2. Select "EDIT"to begin tank level calibration.
DEFAULT CALIBRATION,TANK CALIBRATION :
OR ADD FUEL ?[DFLT] [ADD ]
23994
Select "DFLT" to let SmartCraft calibrate thetank levels. Select "ADD" to calibrate the tanklevels by adding fluid to the tank.
EMPTY TANKCALIBRATING :
THEN PRESS PLUS BUTTON[SKIP] [SAVE]
23995
Empty the tank. Select "SAVE" to calibrate thetank level to empty.
FILL TANK TO 1/4
THEN PRESS PLUS BUTTON[SAVE]
30427
Fill the tank to 1/4 full. Select "SAVE" to calibratethe tank level to 1/4 full.
SMART TOW TACH/SPEED GPS
72
CAL 2 Tachometer Calibration ‑ Tank 1 and 2 Level Calibration
FILL TANK TO ½
THEN PRESS PLUS BUTTON[SAVE]
30428
Fill the tank to 1/2 full. Select "SAVE" to calibratethe tank level to 1/2 full.
FILL TANK TO 3/4
THEN PRESS PLUS BUTTON[SAVE]
30429
Fill the tank to 3/4 full. Select "SAVE" to calibratethe tank level to 3/4 full.
FILL TANK TO FULL
THEN PRESS PLUS BUTTON[SAVE]
30430
Fill the tank to full. Select "SAVE" to calibratethe tank level to full.
TANK 2 INPUTOIL TANK
CALIBRATION 2
[SAVE][DOWN] [ UP ]24148
Select tank 2 input: oil tank, fuel tank 2, watertank, waste tank, or not installed.
EXTERNAL SENSORS
CAL 2 Tachometer Calibration ‑ External Sensors
EXTERNAL SENSORS ?CALIBRATION 2
[SKIP] [EDIT]24006
Selects and calibrates external sensors that areinstalled in the system. Select "SKIP" to proceedto the speed options. Select "EDIT" to proceedto external sensor selection.
EXTERNAL SENSORSCALIBRATION 2
PITOT SENSOR ? YES[ NO ] [SAVE] [YES ]
24007
Is the boat equipped with a pitot sensor tomeasure boat speed? Press "‑" to select "NO"or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
PADDLE SENSOR ? YES[ NO ] [SAVE] [YES ]
24008
Is the boat equipped with a paddle wheel tomeasure boat speed? Press "‑" to select "NO"or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
TRIM SENSOR ? YES[ NO ] [SAVE] [YES ]
24009
Is the boat equipped with a trim sensor? Press"‑" to select "NO" or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
SEA TEMP ?[ NO ] [SAVE] [YES ]
24010
YESIs the boat equipped with a seawatertemperature sensor? Press "‑" to select "NO" or"+" to select "YES".
SMART TOW TACH/SPEED GPS
73
CAL 2 Tachometer Calibration ‑ External Sensors
EXTERNAL SENSORSCALIBRATION 2
STEERING SENSOR ?[ NO ] [SAVE] [YES ]
24011
YES Is the boat equipped with a steering sensor?Press "‑" to select "NO" or "+" to select "YES".
EXTERNAL SENSORSCALIBRATION 2
INVERT STEERING ?[ NO ] [SAVE] [YES ]
30432
YESChanges the position (direction) of the steeringdisplay. Press "‑" to select "NO" or "+" to select"YES".
SPEED OPTIONCALIBRATION 2
[SKIP] [EDIT]24012
This section configures the following speedsensors. Select "EDIT" to calibrate the sensors.Select "SKIP" to proceed to the depth sensorscreen.
PITOT SENSOR100 PSI TYPE
CALIBRATION 2
[ NO ] [SAVE] [YES ]24014
Select pitot transducer type. Choose between100 or 200 psi. (100 psi is the most common.)
PITOT SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24018
MULTIPLIER = 1.00
Adjust the pitot pressure sensor to correctdisplay readings that are too high/low. Press "‑"or "+" to calibrate the pitot sensor multiplier"DOWN" or "UP".
PADDLE SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24021
PULSEFACTOR = 3.0
Adjust paddle wheel frequency to correctdisplay readings that are too high/low. Press "‑"or "+" to calibrate the paddle sensor pulse factor"DOWN" or "UP".
TRANSITION SPEEDCALIBRATION 2
[DOWN] [SAVE] [ UP ]24022
TRANSITION = 30 MPH
Set the speed at which the gauge stops readingthe paddle wheel and starts using pitot sensorto measure boat speed. Press "‑" or "+" tocalibrate the transition speed "DOWN" or "UP".
DEPTH SENSORCALIBRATION 2
[DOWN] [SAVE] [ UP ]24023
OFFSET = 3 FEET
Electronically configure a depth offset. Enteringa negative number gives you a water line offset.A positive number gives you a keel offset. Press"‑" or "+" to calibrate the depth sensor offset"DOWN" or "UP".
DEPTH ALARMCALIBRATION 2
[DOWN] [SAVE] [ UP ]24024
LEVEL = 2.5 FEET
Enter a depth value. When the depth transducerreads that value or below, the shallow wateralarm will sound. Press "‑" or "+" to calibrate thedepth alarm level "DOWN" or "UP".
[ NO ] [ YES ] [CAL 1]24025
CALIBRATION 2
EXIT ? Press "MODE/SELECT" to exit. Press "‑" to goto the start of CAL 2. Press "+" to continue to"CAL 1."
SMART TOW TACH/SPEED GPS
74
Cruise Control OperationNOTE: Cruise control is only available with Gen I (2007) and newerDTS engines.
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
b a
SMART TOW ON
1000 CRUISELAUNCH
+ / - TO DISENGAGERPM SET
c
30522
a - Increase set cruise RPMb - Decrease set cruise RPMc - Set cruise RPM
NOTE: The cruise control minimum maximum range may changedepending on engine type.There are two modes of cruise control: "RPM MODE" and "SPEEDMODE". Set the cruise control to "RPM MODE" with either theSmart Tow Tachometer or Smart Tow Speedometer. Launchcontrol will inherit the mode of control selected.Press and hold the "SELECT" button for approximately threeseconds to toggle between "SPEED MODE" and "RPM MODE".IMPORTANT: Only the Smart Tow Speedometer can togglebetween cruise control "RPM MODE" and "SPEED MODE". SmartTow Tachometer can change from "SPEED MODE" to "RPMMODE" only.The cruise control can be shut off at anytime by pushing the "+"and "‑" buttons simultaneously.
SMART TOW TACH/SPEED GPS
75
When the cruise control is engaged and the throttle is moved belowthe set cruise engine RPM or speed, the engine RPM will decreasewith the throttle movement. When the throttle is moved above theset cruise speed, the cruise control will actively control the enginespeed to the set cruise speed.When the cruise control is disengaged it will remember the setspeed. It will return to that speed when the cruise control isengaged and the throttle is positioned beyond the set cruise speed.Press "SELECT" twice to exit the cruise control screen.TURNING THE SYSTEM ON/OFF
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
b a
SMART TOW ON
1000 CRUISELAUNCH
+ / - TO DISENGAGERPM SET
c
30524SMART TOW OFF
1000 CRUISELAUNCH
+ / - TO DISENGAGERPM SET
d
a - Increase set cruise RPMb - Decrease set cruise RPMc - Set cruise RPMd - Cruise control off
SETTING CRUISE CONTROLTo set the cruise control RPM:1. Push either the "+" or "‑" button to bring up the cruise control
display screen.2. Set desired cruise RPM. When the throttle is in the wide open
throttle position, the set RPM will be the maximum speed.3. Push "+" and "‑" button simultaneously to engage the cruise
control.
SMART TOW TACH/SPEED GPS
76
NOTE: The cruise control must be engaged for both gauges todisplay the active cruise control setting.CANCELING CRUISE CONTROLTo cancel the cruise control: press the "+" and "‑" buttonssimultaneously.
Precise Speed Control Calibration (Optional)The Smart Tow with GPS speedometer is capable of maintainingthe speed within 0.8 km/h (0.5 MPH) of the cruise control setting.It is not mandatory to complete this tutoring exercise for the speedcontrol to function, it will calibrate itself during normal operation.PRECISE SPEED CONTROL CALIBRATIONNOTE: Cruise control is only available with Gen I (2007) and newerDTS engines.
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
b a
SMART TOW ON
10 CRUISELAUNCH
+ / - TO DISENGAGEMPH
c
31030
a - Increase set cruise speedb - Decrease set cruise speedc - Set cruise speed
There are two modes of cruise control: "RPM MODE" and "SPEEDMODE". Set the cruise control to "SPEED MODE" with the SmartTow Speedometer. Launch control will inherit the mode of controlselected.
SMART TOW TACH/SPEED GPS
77
Press and hold the "SELECT" button for approximately threeseconds to toggle between "SPEED MODE" and "RPM MODE".IMPORTANT: Only the Smart Tow Speedometer can togglebetween cruise control "RPM MODE" and "SPEED MODE". SmartTow Tachometer can change from "SPEED MODE" to "RPMMODE" only.ENGAGING THE CRUISE CONTROL1. Push either the "+" or "‑" button to bring up the cruise control
display screen.2. Set the speed to 10 MPH.3. Push "+" and "‑" button simultaneously to engage the cruise
control. When the throttle is in the wide open throttle position,the engine RPM will increase until the set speed is attained.
4. After cruising at 10 MPH for 20 seconds, increase the speed1 MPH.
5. After cruising at 11 MPH for 20 seconds, increase the speed1 MPH.
6. Continue this speed increment process until the craft hasreached its maximum speed.
CANCELING THE CRUISE CONTROLTo cancel the cruise control: press the "+" and "‑" buttonssimultaneously.When the cruise control is disengaged, it will remember the setspeed. It will return to that speed when the cruise control isengaged and the throttle is positioned beyond the set cruise speed.Press "SELECT" twice to exit the cruise control screen.IMPORTANT: Performing a Master Reset will return all thecalibrations to the factory default settings.
SMART TOW TACH/SPEED GPS
78
Launch Control OperationNOTE: Launch control is only available with Gen I (2007) andnewer DTS engines.
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
SMART TOW ON
1000 5+ / - TO DISENGAGERPM SET LAUNCH
30528
b a
dc
a - Raise launch control settingb - Lower launch control settingc - Set cruise RPMd - Launch control setting
BASIC OPERATIONLaunch control determines how fast the engine accelerates to aset cruise speed.
SMART TOW TACH/SPEED GPS
79
Set the launch control with either the Smart Tow Tachometer orSmart Tow Speedometer. The settings are 1, 2, 3, 4, and 5, with1 the most gradual acceleration and 5 the most aggressive. Press"SELECT" once to highlight the launch control setting. Press "+" toincrease launch control setting and "‑" to decrease the launchcontrol setting. This can be accomplished in either "RPM MODE"or "SPEED MODE". The launch control setting will remain untilchanged.
23481
If the cruise control is engaged and none of the numerical launchcontrol settings are selected ("CRUISE" is displayed), launchacceleration is controlled by the throttle up to the RPM set point.The display screen will revert back to the "RPM SET" screen afterfive seconds of inactivity. Push the "SELECT" button to highlightthe launch control display screen.SETTING LAUNCH CONTROLThere are two modes of launch control: "RPM MODE" and "SPEEDMODE". Set the launch control to "SPEED MODE" with Smart TowSpeedometer. Cruise control will inherit the mode of controlselected.Press and hold the "SELECT" button for approximately threeseconds to toggle between "SPEED MODE" and "RPM MODE".
SMART TOW TACH/SPEED GPS
80
IMPORTANT: Only the Smart Tow Speedometer can togglebetween cruise control "RPM MODE" and "SPEED MODE". SmartTow Tachometer can change from "SPEED MODE" to "RPMMODE" only.1. Press "+" or "‑" to bring up the cruise control display screen.2. Push the "SELECT" button to highlight "SET LAUNCH".3. Push "+" to raise the setting and push "‑" to lower the setting.4. Launch control will automatically turn on with the cruise
control.If the cruise control is engaged and none of the numerical orcustomized launch control settings are selected ("CRUISE" isdisplayed), launch acceleration is controlled by the throttle up tothe RPM set point.The display screen will revert back to the "RPM SET" screen afterfive seconds of inactivity. Push the "SELECT" button to highlightthe "SET LAUNCH".CANCELING LAUNCH CONTROLThe launch control will turn off when the cruise control is turned off.
Creating a Customized Launch SettingBeyond launch setting number 5 are eight customized launchsettings. Each customized launch setting name can have up toseven alpha characters to identify the custom launch. The customlaunch setting can be controlled by RPM or speed. To use thespeed setting control, GPS must be interfaced with the SmartCraftgauge through a junction box.NOTE: If the Smart Tow set point is changed while the customizedlaunch is active, the set point will automatically be saved for thatuser .1. Press the "SELECT" button to highlight "SET LAUNCH".2. Advance the launch control setting beyond number 5. After
number 5 the "NEW USER" launch control setting will activate.
SMART TOW TACH/SPEED GPS
81
3. Press and hold the "SELECT" button for approximately threeseconds to edit the customized launch setting.
SELECT
0
RESET
SMART TOW
10SPEED
GPS
2030 40
50
60
70
SMART TOW ON
35.5+ / - TO DISENGAGE
b a
dc
RPM SET LAUNCH30590
eUSERNEW
a - Raise launch control settingb - Lower launch control settingc - Set cruise RPMd - "SELECT" buttone - Launch control setting
Customized Launch Settings
AAAAAAARPM SETNAME
MPH SET100010.0
[DOWN] [EDIT]30595
Press the "SELECT" button to edit the name.
AAAAAAA [ SAVE ][SCRL ] [NEXT]
30597[SCRL ]
Press the "‑" or "+" to scroll through the alphacharacters. Press the "SELECT" button tosave the character and move to the next setof alpha characters. Press the "‑" and"SELECT" buttons to save the customizedlaunch name.
AAAAAAANAME
MPH SET100010.0
[DOWN] [EDIT]30598
RPM SET
[ UP ]
Press the "‑" to move the cursor to "RPMSET". Press the "SELECT" button to edit theRPM.
SMART TOW TACH/SPEED GPS
82
Customized Launch Settings
RPM SET
[DOWN] [ OK ]30599
[ UP ]
Press "‑" or "+" to change the RPM set point.Press the "SELECT" button to exit the RPMedit.
AAAAAAANAME422510.0
[DOWN] [EDIT]30601
RPM SET
[ UP ]MPH SET
Press the "‑" to move the cursor to "MPHSET". Press the "SELECT" button to edit thespeed.
MPH SET
[DOWN] [ OK ]30609
[ UP ]
Press "‑" or "+" to change the speed setting.Press the "SELECT" button to exit the MPHedit.
1.00 %
0.0 S[DOWN] [EDIT]
30614[ UP ]
LAUNCHOVERSHOOTDURATION
Press the "‑" to move the cursor to "LAUNCH".Press the "SELECT" button to edit the level ofacceleration.
LAUNCH
[DOWN] [ OK ]30612
[ UP ]
Press "‑" or "+" to edit the level of accelerationbetween 1.0 and 5.0. Press the "SELECT"button to exit the "LAUNCH" edit.
4.70 %
0.0 S[DOWN] [EDIT]
30615[ UP ]
LAUNCHOVERSHOOTDURATION
Press the "‑" to move the cursor to"OVERSHOOT". Press the "SELECT" buttonto edit the percentage.
OVERSHOOT
[DOWN] [ OK ]30617
[ UP ]MAX : 20%
12 Press "‑" or "+" to edit the percentage toexceed the level of speed or RPM between 0and 20%. Press the "SELECT" button to exitthe "OVERSHOOT" edit.
4.712 %
0.0 S[DOWN] [EDIT]
30619[ UP ]
LAUNCHOVERSHOOTDURATION
Press the "‑" to move the cursor to"DURATION". Press the "SELECT" button toedit the seconds.
SMART TOW TACH/SPEED GPS
83
Customized Launch Settings
DURATION
[DOWN] [ OK ]30620
[ UP ]
3.4 sPress "‑" or "+" to edit the duration of secondsthe overshoot percentage is activated. Thenumber of seconds is between 0 and 4. Pressthe "SELECT" button to exit the "DURATION"edit.
12 %0.0 S
[ OK ]30621
[ UP ]
OVERSHOOTDURATIONEXIT
Press the "‑" to move the cursor to "EXIT".Press the "SELECT" button to exit the launchsetting or press the "+" to review and edit thecustomized launch settings.