smart lock cam lock pl302 › wp-content › uploads › 2016 › 12 › cam-lo… · 4. attach cam...

13
Smart Lock Cam Lock PL302

Upload: others

Post on 28-Jun-2020

7 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

1

Smart LockCam Lock

PL302

Page 2: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

2 3

OverviewReview entire instruction guide and complete cabinet assessment before starting installation. Proper operation requires cam arm to latch to optional bracket or cabinet structure.

Application & Cabinet SpecificationThe Cam Lock is designed for glass, wood or metal swing-out or pull-out doors and drawers with panels up to 21 mm (0.83”) thick. A 19 mm (0.75”) hole is required to mount the lock body into a fixture latch. Latch brack-ets are optional.

System Components1. Cam Lock (PL302)2. Cam Arm*3. L-Bracket or Flat Bracket (optional)4. IR2 Key (PK4400)

Setup in 5 easy steps:1. Gain access to front and back of door or drawer2. Place Cam Lock body into hole from outside of fixture3. Affix anti-rotation brackets (wood or glass applications)4. Attach cam arm to lock body and test alignment and

rotational direction5. Attach latch bracket (L or flat) to cabinet if needed

*The cam arm should rotate without obstruction when locking and unlocking device. InVue offers a broad range of cam arms should it be determined that a different cam arm dimension is required.

Cam Lock PL302

L-Bracket Flat Bracket

Latch Brackets(optional)

IR2 KeyPK4400

Tool Requirements1. Pencil2. Adjustable Wrench3. Power Drill and Bit4. Phillips #1 Screwdriver

Page 3: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

4 5

LOCK ASSEMBLY – WOOD MOUNTNote: Installation instructions in this guide are for wood mount. For glass and metal mount, see page 22 and 23.

CABINET ASSESSMENT

1

23 4

5 6

7

Assembly Sequence1. Cam Lock 2. Wood Mount Bracket3. Wood Mount Screws4. Anti-Rotation Washer5. Cam Lock Nut6. Cam Arm7. Washer & Screw

Page 4: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

6 7

Determine lock body orientation on cabinet. Deter-mine if lock will be installed vertically or horizontally.Note: If there is no existing hole, consider proximity before drilling (consider latch bracket, internal shelving, frame, etc.).

1

Horizontal Mount Vertical Mount

A new lock will arrive in “unlocked” position. Using IR2 Key, lock Cam.

2

Unlocked

Locked

Page 5: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

8 9

Assemble and hand tighten parts 1 - 5 below.4Begin test fitting assembly. Confirm enough space on back panel to screw mount bracket to panel.Note: DO NOT attach screws.

3

47 mm1.85”

26 mm1.02”

Horizontal Mount Vertical Mount

1

23

4

5

Assembly Sequence1. Cam Lock2. Wood Mount Bracket3. Wood Mount Screws (will be applied later)4. Anti-Rotation Washer5. Cam Lock Nut

Note: If parts do not fit onto wood panel, contact InVue’s sales associate.

Page 6: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

10 11

Unlock Cam Lock with IR2 Key. Confirm cam arm rotates correctly without obstruction. Use small switch to change arm direction if needed.

6Cam arm rotates 90 degrees during operation. Cam arm can be placed in 4 different orientations. Attach cam arm in “locked” orientation relative to future loca-tion of latch. Hand tighten washer and screw.

5

Locked

Locked

Unlocked

Unlocked

Switch

Switch

Locked

Latch

Cab

inet

Wal

l

Page 7: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

12 13

Bend prongs on anti-rotation washer onto nut to lock in place.

8Once cam arm orientation is confirmed, remove all hand tightened parts. Reassemble ALL lock parts onto cabinet in order below. Predrill holes for wood mount screws.

7

Assembly Sequence1. Cam Lock2. Wood Mount Bracket3. Wood Mount Screws4. Anti-Rotation Washer5. Cam Lock Nut6. Cam Arm7. Washer & Screw

Locked

Locked

Prongs Before

Prongs After

1

23 4

5 6

7

Page 8: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

14 15

Determine location of latch bracket. Use measurement from step 9a - 2 mm (0.08”) to measure location of latch bracket on inside of cabinet. Position latch bracket with adhesive on back to test fit.

9bOptional for latch bracket: Return lock to unlocked position. To correctly position latch bracket: Measure width between front of cabinet door/drawer and front of cam arm.

9a

Side View Door Panel Unlocked

Bracket Spacing

Bracket Spacing

Calculation: Step 9a measurement - 2 mmExample: 38 mm - 2 mm = 36 mm

Inside Right Cabinet Panel

Page 9: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

16 17

TEST LOCK

IR2 Key

Close door and operate lock. Confirm cam arm rotates behind bracket or cabinet structure without obstruction. If using bracket, attach bracket to cabinet using wood screws provided.Note: Latch bracket and/or cabinet structure create a security system.

10

Bracket

BRACKET OPTION

CABINET STRUCTURE OPTION

Top View Locked

Top View Locked

Cam Arm

Cam Arm

Page 10: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

18 19

2Close cabinet door. Press gray button on key once and wait for “beep” to confirm cabinet is locked. Confirm Cam Lock is “locked.” If Cam Lock shows error, see page 19.

1

Locked

Error(see page 19)

If error, return lock to “unlocked” position using IR Key.

Unlocked

Page 11: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

20 21

LOCK OPERATION USING IR2 KEY

Position IR2 Key against lock, push button and wait for “beep” before removing key. Lock and unlock cabinets several times to ensure proper operation.

IR2 Key must be charged and activated. See IR2 Key instruction guide.

Hold until you get a confirmation “beep.”Note: If double “buzz,” an error has occurred. Unlock, ensure cabinet is fully closed and try again.

Locked

“BEEP”

LOCK STATUS INDICATORS

Locked

Unlocked

Error (not fully locked)Note: Unlock lock. Confirm no obstructions. Fully close cabinet and try again.

Page 12: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

22 23

LOCK ASSEMBLY – GLASS MOUNTNote: Orientation of glass mount bracket (#2) will dictate horizontal or vertical mounting of Cam Lock.

Assembly Sequence1. Cam Lock2. Glass Mount Bracket3. Plastic Washers4. Anti-Rotation Washer5. Cam Lock Nut6. Cam Arm7. Washer & Screw

1

2

3 34 5 6

7

! Caution:Wear appropriate safety gear (gloves and eye protection) when working with and around glass panels.

LOCK ASSEMBLY – METAL MOUNT

Assembly Sequence1. Cam Lock2. Anti-Rotation Washer3. Cam Lock Nut4. Cam Arm5. Washer & Screw

1

2

3 4

5

Optional. If panel thickness is less than 1.5 mm (0.06”), use wood mount bracket as a spacer.

Back of Panel Back of Panel

Page 13: Smart Lock Cam Lock PL302 › wp-content › uploads › 2016 › 12 › Cam-Lo… · 4. Attach cam arm to lock body and test alignment and rotational direction 5. Attach latch bracket

24

© 2013 InVue Security Products Inc. All rights reserved.

InVue is a registered trademark of InVue Security Products.

SD0157 Rev0 03/18/13

www.invuesecurity.com

Corporate Office (North America) // 704.752.6513 • 888.55.INVUEEurope, Middle East & Africa // +31.23.8900150

Asia Pacific // +65.6766.4844Latin America // +52.55.9000.3957