SMOKE DETECTION SYSTEMS IDENTIFY PARTICLES OF

COMBUSTION MOST COMMON TYPES ARE

PHOTOELECTRIC AND IONIZATION

PHOTOELECTRIC DETECTORS

PHOTOELECTRIC DETECTORS PARTICLES OF COMBUSTION

DISTORT A LIGHT BEAM DISTORTED LIGHT BEAM

ACTIVATES SIGNAL

PHOTOELECTRIC DETECTORS

PHOTOELECTRIC DETECTORS

IONIZATION DETECTORS

USE A PIECE OF OF RADIOACTIVE MATERIAL (ALPHA RADIATION)

The alpha particles generated by the americium ionize the oxygen and nitrogen atoms of the air in the chamber.

To "ionize" means to "knock an electron off of." When you knock an electron off of an atom,

you end up with a free electron (with a negative charge) and an atom missing one electron (with a positive charge).

Ionization Detectors

The electronics in the smoke detector sense the small amount of electrical current that these electrons and ions moving toward the plates represent.

When smoke enters the ionization chamber, it disrupts this current -- the smoke particles attach to the ions and neutralize them.

The smoke detector senses the drop in current between the plates and sets off the horn.

IONIZATION DETECTORS

IONIZATION DETECTORS

HEAT DETECTORS

FUSIBLE ELEMENT BIMETALLIC PNEUMATIC RATE OF RISE VERSUS FIXED

TEMPERATURE

Heat Detectors

Rate of Rise Detector

Thermistor Rate of Rise Detectors If the air temperature increases rapidly,

the change of temperature results in a change in resistance between the thermistors.

When the ratio of resistance exceeds a factory preset level, an alarm is initiated.

Pneumatic Rate of Rise Detectors

Detectors use a reliable pneumatic rate-of-rise element which responds to a rapid rise in temperature of approximately 15°F per minute.

When the air within the sealed chamberexpands faster than it can escape through a calibrated vent, the resultant increase in pressure depresses the diaphragm, causing the electrical contact to close the circuit thus initiating the alarmsignal.

Fixed Temperature Heat Detectors The fixed temperature element uses a fusible

alloy and an efficient heat collector. Detectors are normally open devices and are

available in either 135°F (57°C) or 194°F (90°C) ratings.

When activated, the external heat collector drops away to provide quick visual confirmation that the detector has operated.

Fusible Element Heat Detectors

A spot type of fixed-temperature detectors is used mainly in unattended spaces to detect smoldering fires that increase the temperature of a detector above its design value, usually 135°F to 145°F or 185° to 200°F.

The higher temperature devices are used in spaces that may reach higher temperatures under ordinary conditions, such as boiler rooms, attics, or cooking areas.

Fusible Element Heat Detectors

Fusible Element Detectors

The device usually is actuated by the melting or fusing of an element made of a fusible metal alloy.

Actuated devices usually can be detected by visual examination.

In some devices, the smaller diameter part in the center drops away. In others, the dimple becomes a hole when the detector operates.

These fixed-temperature devices are often designed for one-time operation, and the whole device or the element needs to be replaced.

BIMETALLIC HEAT DETECTORS

BIMETALLIC HEAT DETECTORS USES TWO PIECES OF

SANDWICHED METALS THAT EXPAND AND CONTRACT AT DIFFERENT RATES WHEN HEATED

WHEN EXPOSED TO HEAT, THE METAL BENDS TO COMPLETE AN ELECTRICAL BRIDGE AND ACTIVATES THE DETECTOR

UV FLAME DETECTORS

UV Flame Detectors

Ultraviolet detectors respond to flaming fires emitting light in the ultraviolet portion of the spectrum.

UV detectors can respond to a fire condition in less than 10 milliseconds.

UV Flame Detector Uses

The ultraviolet (UV) flame detector is extremely fast and is used in high-hazard applications, such as aircraft maintenance areas, munitions production, and other areas where flammable or explosive liquids or solids are handled or stored.

These detectors should not be used around arc welding, as they will respond to the ultraviolet light given off by the welding process.

IR Flame Detectors

IR Detectors

Infrared detectors respond to flaming fires emitting light in the infrared portion of the spectrum.

IR detectors can respond to a fire condition in less than 50 milliseconds.

These detectors are designed to alarm to hydrocarbon fires, while ignoring things like arc welding, nuclear radiation and x-rays.

IR Detectors

The IR flame detector is ineffective for smoldering or beginning fires.

It is used where possible fires would develop quickly (fuels, such as combustible gases and liquids, or loose cotton fiber), and it is capable of protecting a large area if it is mounted high on a ceiling or wall (30 to 50 feet).

TESTING FLAME-ACTUATED DETECTORS Flame-actuated detectors should be

inspected monthly for physical damage, accumulation of lens deposits, and paint.

A spot of paint on a lens can prevent the detector from "seeing" a critical area in the protected space.

Testing Flame Detectors

Be sure that auxiliary functions of the flame detection system are deactivated

Inform the fire department and persons who would hear the alarm.

False Alarms and Failure to Detect False alarms or failure to detect during

a test may be caused by environmental factors or the aiming of the detector.

Check that detectors are not blocked and that lenses are shielded from direct rays of the sun and other sources of IR, such as welding equipment, in the case of UV detectors.

Testing IR Detectors

The dark spot or dome at the bottom center of each IR device is the lens.

Detector lenses must be kept clean to ensure the earliest possible detection of a fire.

A 250-watt IR heat lamp several feet from the detector can serve as a flame substitute in testing an IR flame detector.

Cleaning UV Detectors

Keep UV detector lenses totally clean. A gradual buildup of contaminants frequently

found in high-hazard spaces (oil, gasoline, petrochemicals, salt, and dust) block UV radiation.

A layer thin enough to be undetectable to the human eye can cause a UV detector to be completely blind.

Clean lenses according to the manufacturer's instructions.

Testing UV Detectors

Test feature designed into some detectors allows for checking the device.

A small UV source inside the detector housing is shielded from directly illuminating the sensor.

A test switch deactivates alarm circuits and illuminates the test lamp.

The test lamp rays pass through the front window to the sensor.

Detector response to the test indicates that the window is clean and that the sensor and electronic circuits are operational.

ALARM SYSTEMS

TYPES– CENTRAL STATION– LOCAL SYSTEM– PROPRIETARY SYSTEM– VOICE SYSTEMS

INSPECT AND TEST AT LEAST ANNUALLY

Fire Alarm Panels

Fire Alarm Panels

Zone Indicators Alarm Indicators

– Fire– Trouble Alarm– Loss of Signal/Connection

Test and Alarm Resets

Annunciator Panels

Located near main entrance of buildings Identify zones for alarms

Annunciator Panel

Pull Stations

Pull Stations

Activate fire alarm in building Single action or dual action Most types these days have method for

determining activation– Break glass bar– Require key to reset

INSPECTION AND TESTING

The employer shall assure that fire detectors and fire detection systems are tested and adjusted as often as needed to maintain proper reliability and operating condition.

Local Fire Codes stipulate testing requirements

OSHA’s Employee Alarm Systems (1910.165)

– OSHA Standards apply emergency employee alarms installed to meet a particular OSHA standard.

– They also apply to discharge or supervisory alarms required on various fixed extinguishing systems or to supervisory alarms on fire suppression, alarm or detection systems if they are intended to be employee alarm systems.

OSHA’s Fire Detection Systems Standard (1910.164) Applies to all automatic fire detection

systems installed to meet the requirements of a particular OSHA standard.

Example: 1910.38 Emergency Action Plans and Fire Prevention Plans

NFPA 72: National Fire Alarm and Signaling Code Addresses design, installation, testing,

and maintenance of alarm systems. Qualifications for installers, inspectors,

monitoring personnel.