soluções em pelotização (maintenance)
DESCRIPTION
Dean Connor Dean Connor é gerente de vendas para a área de piroprocessamento na Metso nos Estados Unidos. Com 36 anos de experiência na indústria de minério de ferro, Dean começou sua carreira como engenheiro de campo, responsável por sistemas Grate-Kiln da Allis-Chalmers. Desde 2001 tem sido responsável pela linha de produtos que inclui também o carro grelha.TRANSCRIPT
Iron Ore Straight Grate Pelletizing Seminar
Machine Maintenance
to improve operating conditions
October 2014
© Metso© Metso
Tempering
Damper
|
Simplified Grate Kiln System Flow
2
600 oF
315 oC
550 oF
290 oC
1800 oF
980 oC
700 oF
371 oC
230 oF
110 oC
230 oF
110 oC
© Metso© Metso
METSO MINERALS
Rails
Top Strand
Bottom Strand
Burners
Direct Recup Header
Windbox
Double Dump Valve
Air Passage
Downcomer
Furnace Hood
3
© Metso© Metso
Machine AlignmentMachine alignment is critical to health of the major components of the machine.
Pallets, sprockets, guide rails, and machine drive.
4
© Metso© Metso BMH 20075
Measure bushing axial and radial wear.Inspect Shaft Seals
© Metso© Metso
Machine Shaft Alignment
1) Machine drive and idler shaft should be level at the pillow blocks within
1/8”
2) Sprocket Teeth should be aligned perpendicular to the strand centerline
with 1/16” or less. This needs to be done with a laser for accuracy. If
teeth are worn differentially they should be replaced. Sprocket teeth
can be re-aligned using the index provision built into the one of the
sprocket hubs.
6
© Metso© Metso
Sprocket Indexing
7
© Metso© Metso
Sprocket Segment- Profile Gauge
Machine alignment guide rail and roller wear can be caused by sprocket
wear. Use gage to determine. Wear should not be > 3/16”.
8
© Metso© Metso
Machine Alignment- Flanging
If the sprocket shaft and teeth are within acceptable limits, Pallet wheel
flanging can be reduced by re-orientation of the pillow blocks by:
9
© Metso© Metso
Machine Alignment- Flanging
X= B*C/(2 *A)
A is dimension measured to location of flanging pallet wheel from
centerline sprocket (Inches)
B is the wheel gap on opposite side of flanging wheel (Inches)
C is centerline sprocket dimension ( use 254 inches)
Amount Pillow movement= X
10
© Metso© Metso
Possible Causes Guide Rails to Sprocket Misalignment
1) Transverse movement of the sprocket due to end wear of
the shaft bushings
2) Differential or excessive wear of the guide rails
3) Distorted or damaged guide rail supports
11
© Metso© Metso
Guide Rails to Sprocket Alignment
“A” should be within 1/8”12
© Metso© Metso
Machine Alignment- Rails and Guide Rails Gauge
13
© Metso© Metso
Machine Alignment- Rails and Guide Rails Gauge
14
© Metso© Metso
Guide Rails Wear Gauge
15
© Metso© Metso16
© Metso© Metso
Tipping Wheel Assembly
17
© Metso© Metso18
Discharge Sprocket
Discharge Guide Rail
Tipping Wheel assemble Area
Spillage Chute
Bearings
© Metso© Metso BMH 200719
Mechanical ImprovementsTipping Wheel Shaft Seals
© Metso© Metso
Pallet Roller Turner
20
© Metso© Metso BMH 200721
Mechanical ImprovementsProcess Seals - Counterweighted Deadplates
© Metso© Metso Date Author Title
Counterweighted Deadplates
22
Direction of Pallet Travel
© Metso© Metso BMH 200723
Mechanical ImprovementsOne Counterweighted Deadplate
© Metso© Metso BMH 200724
Mechanical ImprovementsOne Set of Counterweighted Deadplates
© Metso© Metso Date Author Title
Pallet End Arrangement
25
Pallet Wheel
(Engages Rails)
Carrying Rail
Pallet Roller (Engages Sprockets)
Hood Seal Bar
(Engages Drop Seal)
Spring Seal (Engages Slide Bars)
WindboxSlide Bars
© Metso© Metso Date Author Title
Lintel Wall & Drop Seal BarDrop Seal Bars ride against seal plate on pallet car. This prevents
gas from entering/leaving machine.
26
© Metso© Metso Date Author Title
Pallet Car Camber
27
© Metso© Metso Date Author Title
Cambered Pallet (New)
28
© Metso© Metso Date Author Title
Sagged Pallet (Need Maintenance)
29
© Metso© Metso
Summary
• ALIGNMENT, rails, drive & tipping wheel shafts, lintel walls and windbox
seals
• Monitor sprocket wear, maximum of 5 mm
• Well maintained Pallet Cars
• Well maintained seals
• Maintain daily, weekly, monthly and yearly recommended inspections
Date Author Title30
© Metso© Metso
Tempering
Damper
|
Simplified Grate Kiln System Flow
31
600 oF
315 oC
550 oF
290 oC
1800 oF
980 oC
700 oF
371 oC
230 oF
110 oC
230 oF
110 oC
© Metso© Metso BMH 200732
Available Services
Pallet Repair Program
• Establishes a pallet weld repair procedure
• Supplies gauges and dimensions to monitor wear, determine degree of reconditioning
and to determine when pallets should be turned over.
• Supplies evaluation procedure for end casting repairs and for maximizing wheel/axle
and bearing life.
• Establishes a constant ongoing program of monitoring, repairing and replacing the
most worn pallets.
© Metso© Metso BMH 200733
Available Services
Maintenance Training
• Establishes the pallet repair procedure at the plant level (pallet removal from
machine, repair, assembly and reinsertion into machine).
• Establishes mechanical and electrical preventative maintenance programs for the
entire indurating machine
General Inspections
• Helps to pre-plan maintenance outages for determining and prioritizing needed repairs
• Recognizes and corrects minor problems that can expand into major problems
• Determines that the pallet repair program is being properly maintained and utilized
34