sonora design directv mfh2 (6) input products 1 · pdf filesonora design directv mfh2 (6)...

Contact: Sonora Design Associates 805.644.8913 www.sonoradesign.com [email protected]

Revised May 19 2011

1SONORA DESIGN DIRECTV MFH2 (6) INPUT PRODUCTS

SD PI-6S Trunk Power Inserter

• Powers SL5, 95W & 72.5W ODUs

• Regulated DC Voltages

• F-Connector Power Input

• Dual 10 AWG Ground Lugs

• Dual Color LED Indicators

• SCTE Indoor F-Connectors

SD MST-6xx Trunk Tap

• Passes DC Voltage Out-to-In

• DC Blocking on Tap Port


• Tap values 6 dB, 9 dB, 12 dB & 16 dB


SD SA-6AL Trunk Amplifi er

• Automatic Gain Control: 20 dB window

• Weather Sealed Die-Cast Housing


• Variable Color Signal Indicators



PS242000A & PS121000A DC Power Supplies

• UL Approved

• 24 Volt 2 Amp or 12 Volt 1 Amp

• Interchangeable AC Cord

• F-Connector for DC Input

• Overload Protection

SD SWM-E2 Dual SWM Expander

• Connect (2) SWM8 or SWM16 switches to one dish

without splitters or jumpers

• Passes LNB power to dish from one SWM


• Replaceable F threaded to push-on quick connects




Revised May 19 2011

2SD PI-6S TRUNK POWER INSERTER

Parameter UNIT SD PI-6S

Operating Frequency Range MHz 250 - 2150

Insertion Loss dB 1.5 (max.)

Flatness in operating frequency range dB ± 0.5

Number of Input Ports Each (6) SCTE Indoor F

Number of Output Ports Each (6) SCTE Indoor F

Isolation between ports dB > 35 dB

Input / Output Return Loss dB > 10 (min)

DC Power provided to inputs VDC

Port #1 (20 V 101º & 99º) VDC 20 ± 0.5

Port #2 (13 V 101º & 99º) VDC 13.5 ± 0.5

Port #3 (22 kHz & 20 V 119º & 103º) VDC 20 ± 0.5 (+ 22 kHz)

Port #4 (22 kHz & 13 V 119/110º & 103º) VDC 13.5 ± 1 (+ 22 kHz)

Port #5 (Flex Port 1) VDC 20 ± 1 or 13.5 ± 1

(Internally switch able)

Port #6 (Flex Port 2) VDC20 ± 1 or 13.5 ± 1

(Internally switch able)

LED Color corresponding to: GREEN

AMBER

VDC

VDC

10.0 - 14.5

17.0 - 20.5

Number of LEDs Each 7 (1 per input & 1 for adaptor input)

22 kHz Tone to ODU kHz

Frequency kHz 22.0 ± 0.5

Duty Cycle % 50

Amplitude mVpp 800 (min)

DC Power Path mA 1000 (max.) From DC Input to each

Input

DC Power Connector Type Each (1) SCTE Indoor F

Switching Mode Power Supply 24 V, 1.2 A (min)

Short Circuit Protection Yes, 1 A Multi fuse

Lightning Surge Protection 32 V p-p, max shunt current 200 A;

8 msec, 1.5 kW max dissipation

Ground Screws Each 2 Green Screw Ground pt.

Dimensions L x W x H mm 136 x 217 x 23

Environmental Requirements Indoor use only

Operating Temperature range ºC -34 to + 60 Indoor housing

HumidityShall survive 95% relative humidity

over operating temperature

MDU switch able Power Inserter and Tone Generator UnitSimplifi es MDU installations by providing an integrated module for

locking LNB polarizations and satellite selection

SD PI-6S Trunk Power Inserter

• Powers SL5, 95W & FLEX2 ODUs

• Regulated DC Voltages



• Dual Color LED Indicators

PS242000A DC Power Supplies

• UL Approved

• 24 Volt 2 Amp





Revised May 19 2011

3SD SA-6AL (6)TRUNK AMPLIFIER

Self-adjusting in-line trunk amplifi er with LED signal level indicators

• Simplifi es MDU installations by providing self-adjusting, automatic gain control for optimum signal level

• Provides LED indicators to show signal levels

Parameter UNIT SD SA-6AL Operating Frequency Range MHz 250 - 2150

Maximum Output (IM3, 35 dBc) 2 carriers

@ 250 MHz

@ 750 MHz

@ 950 MHz

@ 1450 MHz

@ 2150 MHz

dBm

dBm

dBm

dBm

dBm

-6.0 min

-5.0 min

-4.0 min

-3.0 min

-3.0 min

Gain Below AGC dB 20 - 25 min Fixed Slope

Input Level (Colored LED Indicator)

Red Blinking: Signal Below AGC window

Green : Signal Inside AGC window

Red : Signal is Above AGC window

dBm

dBm

dBm

Input Signal < - 51

Input Signal @ - 50 to - 28

Input Signal > -28

Inter Stage Attenuator dB 0 to 20 dB min

Isolation Satellite to Satellite dB > 30 dB

Input Return Loss dB >10

Output Return Loss dB >10

Noise Figure dB 7 (2150 MHz)

Number of Inputs Each 6 SCTE Indoor F

Number of Outputs Each 6 SCTE Indoor F

Power Model PS121000A

DC Power Pass (any Output to Input) mA 1000 (max)

Input DC voltage VDC 10 (min.), 20 (max.) from any Output

or 12 VDC from SMPS Power Adaptor

Max Power Consumption mA 600 (max.)

Lightning Surge Protection 32 V p-p, max shunt current 200 A;

8 msec, 1.5 kW max dissipation

Ground Screws Each 2 Green Screw Ground pt.


Environmental Requirements Indoor Only

Operating Temperature range ºC -34 to + 60

Storage Temperature ºC -50 to + 85

Humidity Shall survive 95% relative humidity


SD SA-6AL Trunk Amplifi er

• Maximum Gain 30 dB @ 2150 MHz

• Automatic Gain Control 22 dB

• Weather sealed Die-Cast Housing


• Variable Color Signal Indicators

PS121000A DC Power Supply

• UL Approved

• 12 Volt 1 Amp





Revised May 19 2011

4SD MST6xx MFH2 (6) TRUNK TAP

PARAMETER UNIT SD MST6xx

Operating Frequency MHz 5 -2150 MHz

Number Input / Output /

Tap PortsEach 6 SCTE Indoor

DC Power Output to Input Amps 3

Ground Studs Each 2


Operating Temperature ºC -34 to + 60 Indoor / Lock box



SD MST606

6 dBInsertion Loss

In-OutInsertion Loss

In - TapIsolationOut - Tap

Return LossINPUT

Return LossOUTPUT

Return LossTAP

Port to Port Isolation

5-250 MHz 3.4 ±0.2 6.3 ±0.2 >18 dB >12 dB >12 dB >12 dB >45 dB

250-1850 MHz 3.9 ±0.2 6.3 ±0.2 >18 dB >12 dB >12 dB >12 dB >45 dB

1850-2150 MHz 5.3 ±0.2 6.9 ±0.2 >18 dB >12 dB >12 dB >12 dB >40 dB

SD MST609

9 dBInsertion Loss



Return LossINPUT

Return LossOUTPUT

Return LossTAP


5-250 MHz 1.8 ±0.2 8.3 ±0.2 >18 dB >12 dB >12 dB >12 dB >45 dB

250-1850 MHz 2.7 ±0.2 8.3 ±0.2 >18 dB >12 dB >12 dB >12 dB >45 dB

1850-2150 MHz 5.2 ±0.2 7.2 ±0.2 >18 dB >12 dB >12 dB >12 dB >45 dB

SD MST612

12 dBInsertion Loss



Return LossINPUT

Return LossOUTPUT

Return LossTAP


5-250 MHz 1.5 ±0.2 11.5 ±0.2 >18 dB >12 dB >12 dB >12 dB >35 dB

250-1850 MHz 2.1 ±0.2 11.4 ±0.2 >18 dB >12 dB >12 dB >12 dB >35 dB

1850-2150 MHz 3.3 ±0.2 10.6 ±0.2 >18 dB >12 dB >12 dB >12 dB >35 dB

SD MST616

16 dBInsertion Loss



Return LossINPUT

Return LossOUTPUT

Return LossTAP


5-250 MHz 1.0 ±0.2 16 ±0.2 >18 dB >12 dB >12 dB >12 dB >35 dB

250-1850 MHz 1.4 ±0.2 15.5 ±0.2 >18 dB >12 dB >12 dB >12 dB >35 dB

1850-2150 MHz 2.2 ±0.2 15.5 ±0.2 >18 dB >11 dB >12 dB >10 dB >35 dB

MFH2 Multi-Satellite Tap allows SWM expansion Chassis to be connected to a common satellite distribution backbone

SD MST6xx Trunk Tap

• (6) Trunk Capacity

• Passes DC Voltage Out-to-In

• DC Blocking on Tap Port

• 10 AWG Ground Lug

• LED Indicators

MODEL# Description UPC #SD MST606 (6) Input , 6 dB Multi-Tap 609465599014

SD MST609 (6) Input , 9 dB Multi-Tap 609465599021




Revised May 19 2011

5SD SA-6AL & SD MST6xx HIGH RISE MDU

Tap per Floor, (5) Floor Amp Spacing

Amplifier spacing is (5) floors with a minimum IDF

output of -45 dBm.

Model SD SA-6AL with automatic gain control simplifi es

the expansion of DBS Ka/Ku signals. They serve well in

cascades for MDU multiple IDF applications.

Note the FLEX2 port has extended bandwidth to allow

amplifi cation of Off -Air or CATV signals.

Model SD MST6xx directional couplers follow amplifi ers

to feed distribution hubs. The typical insertion loss is

listed.

MHz/ dB 250 950 1450 1850

RG-6 100 ft 3.1 6.4 7.9 9.0

MST616 1.0 1.3 1.5 2.0

MST616 1.0 1.3 1.5 2.0

MST612 1.5 1.8 2.5 3.0

MST609 1.8 2.0 3.0 4.0

MST606 3.4 3.8 4.0 4.5

TOTAL 11.8 16.6 20.4 24.5

Tap output is the input level to the tap less the tap value

( -20 dBm into a 16 dB tap = -36 dBm)

SONORA measured 24 dB insertion loss of the cascade

for (5) taps and 100 feet of RG-6 at 1850 MHz to

determine the 5 dB average loss per tap.

The loss at 250 MHz was 11 dB. The SD SA-6AL internal

slope compensation off sets 9 dB of the 12 dB slope.

Select SWMBOX size and quantity based on subscriber

penetration rates.

TT T T T T

ROOF

9

8

7

6

4

3

2

1

FLOOR10

FLOOR5

CA24RIN DC OUT

10199

SL5103

110 119 worldDIRECT10195

-49 dBm

-30 dBm

-20 dBm

150 feet RG6

DC

SD SA-6ALFLEX 1 FLEX 2

FLEX 1 FLEX 2

SEQ509

FLEX 1

FLEX 1

DC


FLEX 1 FLEX 2

PS12

1000

DC

SD PI-6S

FLEX 2

FLEX 1 FLEX 2

PS242000A

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SD MST616

-37 dBm

SDMST616

-40 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST612

-40 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST609

-41 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST606

-44 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST612

-41 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST609

-41 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST606

-44 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST616

-36 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST616

-40 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

-21 dBm

-24 dBm

-28 dBm

-33 dBm

-38 dBm

-20 dBm

-45 dBm

-23 dBm

-27 dBm

-32 dBm

-38 dBm

20 ft RG6 per floor1 floor spacing5 dB ave loss including taps

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx


Revised May 19 2011

6

Tap per (2) Floors, (8) Floor Amplifi er Spacing

Model SD SA-6AL amplifi er spacing is (8) fl oors when

taps are placed on alternating fl oors.

Model SD SA-6AL is followed with model HRvT1xx taps spaced on alternating fl oors connected via RG-6

coax. The confi guration lowers costs for low penetration

buildings.

Model SD MST6xx directional couplers follow amplifi ers

to feed distribution hubs. The typical insertion loss is

listed.

MHz/ dB 250 950 1450 1850

RG-6 144 ft 4.7 9.2 11.4 13.0

MST616 1.0 1.3 1.5 2.0

MST612 1.5 1.8 2.5 3.0

MST609 1.8 2.0 3.0 4.0

MST606 3.4 3.8 4.0 4.5

TOTAL 12.4 18.1 22.4 26.5

Tap output is the input level to the tap less the tap value

( -20 dBm into a 16 dB tap = -36 dBm)

SONORA measured 26 dB insertion loss for the cascade

of (4) taps and 144 feet of RG-6 at 1850 MHz to

determine the 6 dB average loss per tap.

The loss at 250 MHz was 12 dB. The SD SA-6AL internal

slope compensation off sets 9 dB of the 14 dB slope. Use

model SEQ509 in front of the SD SA-6AL on fl oor 8 for

an additional 8 dB slope compensation.

Select SWMBOX based on penetration rates.

TT T T T T

ROOF

14

15

12

13

11

10

9

6

7

5

4

3

2

1

FLOOR16

FLOOR8

CA24RIN DC OUT

10199

SL5103


-48 dBm

-30 dBm

-45 dBm

-20 dBm

150 feet RG6

DC


FLEX 1 FLEX 2

SEQ509

FLEX 1

FLEX 1

DC


FLEX 1 FLEX 2

PS12

1000

DC

SD PI-6S

FLEX 2

FLEX 1 FLEX 2

PS242000A

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SD MST616

-37 dBm

SDMST612

-38 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

SDMST616

-36 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

-21 dBm

-26 dBm

SDMST609

-41 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

-32 dBm

SDMST606

-44 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

-38 dBm

-46 dBm

-20 dBm

SDMST612

-37 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

-25 dBm

SDMST609

-40 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

-31 dBm

SDMST606

-43 dBm

FLEX 1 FLEX 2

FLEX 1 FLEX 2

-37 dBm

18 ft RG6 per floor2 floor spacing6 dB ave loss including taps

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SWMBOX-xx

SD SA-6AL & SD MST6xx HIGH RISE MDU


Revised May 19 2011

7SD SWM-E2 (2) SWM EXPANDER

Parameter UNIT SD SWM-E2

Operating Frequency Range MHz 250 - 2150

Number of Input Ports Each 6

Number of Output Ports Each 12 (6 per SWM Module)

Insertion Loss dB -6 dB

Flatness @ 36 MHz dB ± 0.5

Isolation In / Out dB > 40 dB

Out / Out dB 15 dB typ.

Input / Output Return Loss dB > 10 dB

Connectors

Inputs type F female

Outputs F female

Output Adaptors type (10) F male to F female push on

Quick F (model PF71-HR)

Ground Studs Each 2 with Green Screw


Environmental Requirements

Operating Temperature Range ºC -34 to + 60 Indoor / Lock box



MODEL# Description UPC #

SD SWM-E2MFH2 (6) Input splitter with Quick F

interface to (2) SWM switches609465599052

PS242000A SMPS power adaptor for SWM powering 609465599373

Features • Simplifi es MDU installations by providing easy connection of (2)

SWM8 or SWM16 switches • Push-On adaptors are fi eld replaceable (Model PF71-HR)

SD SWM-E2 SWM Expander

• Splits MFH2 signals to (2) SWMs

• Weather sealed Die-Cast Housing

• Precision Push-on F-Connectors

• (2) #10 AWG Ground Lugs


• UL Approved

• 24 Volt 2 Amp





Revised May 19 2011

8

SD PI-6S and SD SWM-E2

When the dish is within 100 feet of the distribution

closet, only polarity locking is required.

Model SD PI-6S powers the LNBs’ polarity locks the

internal LNB switches and blocks control signals from

SWM switches from talking to the LNBs’.

Model SD SWM-E2 is connected to the SD PI-6S with

color coded mini-jumpers model 5mJFP24.

Model MSAT-4 splitters are connected to SWM1 and

SWM2 output connectors of the SWM8.

Model BSFR0-01 band-stop fi lters prevent ALL multi-

room viewing programs from being viewed by another

apartment.

Most residential properties require more than two tuners

per apartment.

The above example can be quickly upgraded to (4)

tuners per apartment (at 75% penetration) by replacing

the SWM8 switches with SWM16 switches press-fi t into

the SD SWM-E2 expander.

Model MSAT-2 splitters are connected to SWM1 and

SWM2 output connectors of the (2) SWM16s’.

Model BSFR0-01 band-stop fi lters prevent ALL multi-

room viewing programs from being viewed by another

apartment.

GARDEN STYLE MDU, 100 FT TO DISH

APT 1 APT 4APT 3APT 2



MS

AT

-2 BS

BS

MS

AT

-2 BS

BS

MS

AT

-2 BS

BS

MS

AT

-2 BS

BS

MSAT-2MSAT-2MSAT-2MSAT-2


(2) TUNER 75% PENETRATION

Legacy 1

Legacy 3

Legacy 2

OFF-AIR

SWM1 PWR

SWM2

S W M 8

99º/101º 103º/110º/119º

18V 13V18V22k

13V22k

FlexPort1

FlexPort2

Legacy 1

Legacy 3

Legacy 2

OFF-AIR

SWM1 PWR

SWM2

S W M 8

99º/101º 103º/110º/119º

18V 13V18V22k

13V22k

FlexPort1

FlexPort2

FACE DOWN

DC

DC+RFDC+RF

HRFPIB2-2300 MHz

PS242000A

-40 dBm (MIN)

DC

SD PI-6S

FLEX 2

FLEX 1 FLEX 2

PS242000A

10199

SL5103





MS

AT

-2 BS

BS

MS

AT

-2 BS

BS

MS

AT

-2 BS

BS

MS

AT

-2 BS

BS

Legacy 1

Legacy 3

Legacy 4

FLEX1 OUT

FLEX2 OUT

Legacy 2

SWM2

SWM1 PWR

DC / PWR

S W M 1 6

99º/101º 103º/110º/119º

18V 13V18V22k

13V22k

FlexPort1

FlexPort2

Legacy 1

Legacy 3

Legacy 4

FLEX1 OUT

FLEX2 OUT

Legacy 2

SWM2

SWM1 PWR

DC / PWR

S W M 1 6

99º/101º 103º/110º/119º

18V 13V18V22k

13V22k

FlexPort1

FlexPort2

FACE DOWN

DC

DC+RF DC+RFHRFPIB2-2300 MHz

PS242000A



(4) TUNER 75% PENETRATION

LA141R

12V

OUT

SWM

12V

24V

24V

PS12

250

-40 dBm (MIN)

DC

SD PI-6S

FLEX 2

FLEX 1 FLEX 2

PS242000A

10199

SL5103



Revised May 19 2011

9SONORA DESIGN DIRECTV TRUNK POWER SUPPLIES

Parameter UNIT PS121000A

Rated Input Voltage Vac 100 to 240

Operating Input Range Vac 90 to 264

Rated Input Frequency Hz 47 to 63

Rated Input Current A 0.4 max

No Load Input Current mA < 20

Maximum Input Power W 16.58

AC Input Cable Feet 6

AC Input connector Mini 2 pin

Nominal DC Output Voltage Vdc 12

Rated load current A 1 max

Minimum load current A 0.05A

Ripple & Noise mVp-p 120

DC Output Cable Feet 6

Switching Effi ciency % 72

DC Power Connector Type Each (1) F Female

DC Adaptor included Each (1) F71 Male to Male

Short Circuit Protection Yes, Multi fuse



Ambient Temperature range ºC 0 to + 45



Safety Ratings Agencies USA

Canada

Europe

Japan

Taiwan

China

Britain

UL60950-1

CSA C22.2 NO.950

TUV/VDE-EN60950-1

J60950(H14)/J55001(H14)

CNS13438

GB4943-2001

EN60950-1:2000


• UL Approved


• F-Connector for DC Output



Revised May 19 2011

1 0SONORA DESIGN DIRECTV TRUNK POWER SUPPLIES

Parameter UNIT PS242000A







AC Input Cable Feet 6

AC Input connector Mini 2 pin


Rated load current A 2.08 max

Minimum load current A 0.05A













Canada

Europe

Japan

Taiwan

China

Britain

UL60950-1

CSA C22.2 NO.950

TUV/VDE-EN60950-1

J60950(H14)/J55001(H14)

CNS13438

GB4943-2001

EN60950-1:2000


• UL Approved





Revised May 19 2011

1 1LA141R-T MFH2 SWM EXTENDER

SWiM Output amplifi er with integrated sub-band diplexer• Provides 14 dB of gain which off sets an additional 200 ft of RG-6

• Passes 2 to 40 MHz signals in both directions for SWM & data modem communication

Parameter UNIT LA141R-T

Operating Frequency Range MHz

MHz

MHz

MHz

54-940 (Off -Air / SMATV)

950 - 2150 (SWiM)

2.3 (FSK Communication Channel)

30 - 40 (Return Path)

IM2 / IM3 2 carriers

@ 250 MHz (-2 dBm Out)

@ 750 MHz (-1 dBm Out)

@ 950 MHz ( 0 dBm Out)

@ 1450 MHz ( +2 dBm Out)

@ 1650 MHz (+3 dBm Out)

@ 2150 MHz (+3 dBm Out)

dBc

dBc

dBc

dBc

dBc

dBc

IM3 ΔF 6 MHz, IM2 ΔF 400 MHz

> 45

> 45

> 45

> 45

> 45

> 45

Number of Input / Output Ports Each (1) F

Input / Output Return Loss

2 to 40 MHz

54 to 250 MHz

250 to 2150 MHz

dB

dB

dB

> 8 dB

> 10 dB

>14 dB

Gain / Loss Note

2.3 MHz dB -3 maximum

54 MHz dB 8 minimum

250 MHz dB 9 minimum



Flatness @ 36 MHz dB ± 0.25

DC Power Model PS12250

DC Power pass (Output to Input) mA 1500 (max)

Input DC Voltage VDC 10 (min.), 28 (max.) from Input,

Output or SMPS Power Adaptor

AMP DC Power Connector Type (2) “F”

DC Power Indication Each Green LED

Power Consumption W 1.2 @ 12V max

Lightning Surge Protection 32V p-p, max shunt current 200A; 8

msec, 1.5kW max dissipation

Ground Screw Each 1 Screw Ground point


Environmental Requirements Indoor Only

Operating Temperature range ºC -34 to + 60 Indoor / Lock box




Revised May 19 2011

1 2SONORA DESIGN POWER SUPPLIES

Parameter UNIT PS12250







AC Input Connector Type US PIN


Rated load current A 0.25 max

Minimum load current A 0.0 A













Canada

Europe

Japan

Taiwan

China

Britain

UL60950

CSA C22.2 NO.950

TUV/VDE-EN60950

J60950(H14)/J55001(H14)

CNS13438

GB4943-2001

EN60950-1:2000

PS12250 DC Power Supply

• UL Approved

• Small Footprint



sonora design directv mfh2 (6) input products 1 · pdf filesonora design directv mfh2 (6)...

Documents