sony cdx gt460us fm am

7/24/2019 Sony Cdx Gt460us Fm Am

1/46

SERVICE MANUAL

Sony CorporationeVehicle Division

Published by Sony Techno Create Corporation

US Model

Canadian Model

CDX-GT41UW/GT410U

E ModelCDX-GT460U/GT460US

Chinese ModelCDX-GT460U

9-887-470-032007C04-1

2007.03

Ver. 1.2 2007.03

SPECIFICATIONS

CD player section

Signal-to-noise ratio 120 dB

Frequency response 10 20,000 Hz

Wow and flutter Below measurable limit

Tuner sectionFM

Tuning range GT41UW/GT410U:

87.5 107.9 MHz

GT460U/GT460US:

87.5 108.0 MHz (at 50 kHz step)

87.5 107.9 MHz (at 200 kHz step)

FM tuning interval GT460U/GT460US:

50 kHz/200 kHz switchable

Antenna terminal External antenna connector

Intermediate frequency 10.7 MHz/450 kHz

Usable sensitivity 9 dBf

Selectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo), 69 dB (mono)

Harmonic distortion at 1 kHz

0.5% (stereo), 0.3% (mono)

Separation 35 dB at 1 kHz

Frequency response 30 15,000 Hz

AM

Tuning range GT41UW/GT410U:

530 1,710 kHz

GT460U/GT460US:

531 1,602 kHz (at 9 kHz step)

530 1,710 kHz (at 10 kHz step)

AM tuning interval GT460U/GT460US:

9 kHz/10 kHz switchable

Antenna terminal External antenna connector

Intermediate frequency 10.7 MHz/450 kHz

Sensitivity 30 V

USB player section

Interface USB (Full-speed)

Maximum current 500 mA

Power amplifier section

Outputs Speaker outputs (sure seal connectors)Speaker impedance 4 8 ohms

Maximum power output

52 W 4 (at 4 ohms)

The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism NEW

CD Drive Mechanism Type MG-101U-188//Q

Optical Pick-up Name DAX-25A

Continued on next page

CDX-GT41UW/GT410U/GT460U/GT460US

FM/AM COMPACT DISC PLAYER

(Photo: CDX-GT460U)

AUDIO POWER SPECIFICATIONS (US MODEL)POWER OUTPUT AND TOTAL HARMONIC DISTORTION

23.2 watts per channel minimum continuous average power into

4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more

than 5% total harmonic distortion.


2/462


NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostatic

breakdown because of the potential difference generated by the

charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic breakdown and also use

the procedure in the printed matter which is included in the repair

parts.

The flexible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused on

the disc reflective surface by the objective lens in the optical pick-

up block. Therefore, when checking the laser diode emission,

observe from more than 30 cm away from the objective lens.

If the optical pick-up block is defective, please replace the whole

optical pick-up block.

Never turn the semi-fixed resistor located at the side of optical pick-up block.

SERVICE NOTES

CAUTIONUse of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

GeneralOutputs Audio outputs terminal (sub/rear switchable)

Power antenna relay control terminal

Power amplifier control terminal

Inputs BUS control input terminal

BUS audio input terminal

Antenna input terminal

AUX input jack (stereo mini jack)

Tone controls Low: 10 dB at 60 Hz (XPLOD)

Mid: 10 dB at 1 kHz (XPLOD)

High: 10 dB at 10 kHz (XPLOD)

Power requirements 12 V DC car battery (negative ground)

Dimensions Approx. 178 50 179 mm

(71/82 71/8in.) (w/h/d)

Mounting dimensions Approx. 182 53 162 mm

(71/421/861/2in.) (w/h/d)

Mass Approx. 1.2 kg (2 lb. 11 oz.)

Supplied accessories Card remote commander: RM-X151

Parts for installation and connections (1 set)

USB cap

Design and specifications are subject to change without

notice.

US and foreign patents licensed from Dolby

Laboratories.

optical pick-up

semi-fixed resistor

Notes on Chip Component Replacement Never reuse a disconnected chip component.

Notice that the minus side of a tantalum capacitor may be damaged

by heat.

TEST DISCSPlease use the following test discs for the check on the CD section.

YDES-18 (Part No. 3-702-101-01)

PATD-012 (Part No. 4-225-203-01)

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK0

OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!!

LES COMPOSANTS IDENTIFIS PAR UNE MARQUE0

SUR LESDIAGRAMMES SCHMATIQUES ET LA LISTE DES PICESSONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT.NE REMPLACER CES COMPOSANTS QUE PAR DES PICESSONY DONT LES NUMROS SONT DONNS DANS CE MANUELOU DANS LES SUPPLMENTS PUBLIS PAR SONY.

Ver. 1.1


3/463


UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

SERVO BOARDCN2

MAIN BOARDCN350 J-2502-076-1

EXTENSION CABLE AND SERVICE POSITIONWhen repairing or servicing this set, connect the jig (extension cable)

as shown below.

Connect the MAIN board (CN350) and the SERVO board (CN2)

with the extension cable (Part No. J-2502-076-1).

This compact disc player is classified as a CLASS 1 LASER

product. The CLASS 1 LASER PRODUCT label is located on the

exterior.

E model

CD playbackYou can play CD-DA (also containing CD TEXT*), CD-R/CD-

RW (MP3/WMA/AAC files also containing Multi Session) and

ATRAC CD (ATRAC3 and ATRAC3plus format).

Type of discs Label on the disc

CD-DA

MP3

WMA

AAC

ATRAC CD

* A CD TEXT disc is a CD-DA that includes information such as

disc, artist and track name.

This label is located on the bottom of the chassis.

Chinese model


4/464


TABLE OF CONTENTS

1. GENERALLocation of Controls ........................................................ 5

Connections ..................................................................... 6

2. DISASSEMBLY2-1. Sub Panel (FL) Assy ........................................................ 11

2-2. CD Mechanism Block ..................................................... 11

2-3. Main Board ...................................................................... 12

2-4. Servo Board ..................................................................... 12

2-5. Chassis (T) Sub Assy....................................................... 13

2-6. Roller Arm Assy .............................................................. 13

2-7. Chassis (OP) Assy ........................................................... 14

3. DIAGNOSIS FUNCTION ........................................ 15

4. DIAGRAMS4-1. Block Diagram Main Section ...................................... 19

4-2. Block Diagram Display Section .................................. 20

4-3. Printed Wiring Board Main Section ............................ 224-4. Schematic Diagram Main Section (1/3) ...................... 23

4-5. Schematic Diagram Main Section (2/3) ...................... 24

4-6. Schematic Diagram Main Section (3/3) ...................... 25

4-7. Printed Wiring Board Key Section .............................. 26

4-8. Schematic Diagram Key Section ................................. 27

5. EXPLODED VIEWS5-1. Main Section.................................................................... 32

5-2. Front Panel Section ......................................................... 33

5-3. CD Mechanism Section (MG-101U-188//Q) .................. 34

6. ELECTRICAL PARTS LIST .................................. 35

NOTE FOR REPLACEMENT OF THE USB CONNECTOR

(CN902)To replace the USB connector requires alignment.

1. Insert the USB connector into the front panel.

2. Place the KEY board on the front panel and align the terminals

of the USB connector with the holes in the KEY board.

3. Solder the four terminals of the connector.

KEY board

front panel

USB (socket) connector

NOTE FOR REPLACEMENT OF THE SERVO BOARDWhen repairing, the complete SERVO board (A-1206-357-A) should

be replaced since any parts in the SERVO board cannot be repaired.

NOTE FOR THE 24-PIN CONNECTOR (CN901)Do not use alcohol to clean the 24-pin connector (CN901) connecting

the front panel with the main body.

Do not touch the connector directly with your bare hand. Poor contact

may be caused.

Ver. 1.2


5/46


6/466


CONNECTIONS CDX-GT41UW/GT410U

A

B

AUDIO OUT REAR*

BUS AUDIO IN

BUS CONTROL IN

BUS AUDIO IN

BUS CONTROL IN

Source selector*Slecteur de source*

XA-C40

*not supplied non fourni

*AUDIO OUT SUB/REAR

Exemple de raccordement

Remarques (2-A) Raccordez dabord le cble de mise la masse avant de

raccorder lamplificateur. Lalarme est mise uniquement lorsque lamplificateur intgr

est utilis.

Conseil (2-B- )Dans le cas du raccordement de deux changeurs de CD/MD ouplus, le slecteur de source XA-C40 (non fourni) est requis.

Connection example

Notes (2-A) Be sure to connect the ground (earth) lead before connecting

the amplifier.

The alarm will only sound if the built-in amplifier is used.Tip (2-B- )For connecting two or more CD/MD changers, the sourceselector XA-C40 (not supplied) is necessary.


7/467


L

R

BUS AUDIO IN

AUDIO OUT REAR*2

BUSCONTROL IN

2

4

5

1

3

AUDIO OUTREAR/SUB

BUSIN

AMP REM

Max. supply current 0.3 ACourant max. fourni 0,3 A

Fuse (10 A)Fusible (10 A)

Blue/white stripedRay bleu/blanc

ANT REM

RedRouge

YellowJaune

BlackNoir

BlueBleu

WhiteBlanc

GreenVert

PurpleViolet

White/black stripedRay blanc/noir

Gray/black stripedRay gris/noir

Green/black stripedRay vert/noir

GrayGris

Left

Gauche

RightDroit

LeftGauche

RightDroit

*1RCA pin cord (not supplied)*2 AUDIO OUT can be switched SUB or

REAR. For details, see the suppliedOperating Instructions.

*1Cordon broche RCA (non fourni)*2 AUDIO OUT peut tre commut sur SUB

ou REAR. Pour obtenir plus de dtails,reportez-vous au mode demploi fourni.

Purple/black stripedRay volet/noir

*1

Source selector(not supplied)

Slecteur de source(non fourni)

XA-C40

Supplied with the CD/MD changerFourni avec le changeur de CD/MD

Max. supply current 0.1 ACourant max. fourni 0,1 A

from car antenna (aerial) partir de lantenne du vhicule

Supplied with XA-C40Fourni avec le XA-C40

2

Schma de raccordement

1 un point mtallique de la voitureBranchez dabord le cble de mise la masse noir et,ensuite, les cbles dalimentation jaune et rouge.

2 Au cble de commande dantenne lectriqueou au cble dalimentation de lamplificateurdantenneRemarques Il nest pas ncessaire de raccorder ce cble sil ny a pas

dantenne lectrique ni damplificateur dantenne, ou avecune antenne tlescopique manuelle.

Si votre voiture est quipe dune antenne FM/AMintgre dans la vitre arrire/latrale, voir Remarquessur les cbles de commande et dalimentation .

3 Au niveau de AMP REMOTE IN delamplificateur de puissance en optionCe raccordement sapplique uniquement aux amplificateurs.Le branchement de tout autre systme risquedendommager lappareil.

4 la borne +12 V qui est alimente quand lacl de contact est sur la position accessoiresRemarques Sil ny a pas de position accessoires, raccordez la borne

dalimentation (batterie) +12 V qui est alimente enpermanence.Raccordez dabord le cble de mise la masse noir unpoint mtallique du vhicule.

Si votre voiture est quipe dune antenne FM/AMintgre dans la vitre arrire/latrale, voir Remarquessur les cbles de commande et dalimentation .

5 la borne +12 V qui est alimente enpermanenceRaccordez dabord le cble de mise la masse noir unpoint mtallique du vhicule.

Connection diagram

1 To a metal surface of the carFirst connect the black ground (earth) lead, then connect theyellow and red power supply leads.

2 To the power antenna (aerial) control lead orpower supply lead of antenna (aerial) boosterNotes It is not necessary to connect this lead if there is no power

antenna (aerial) or antenna (aerial) booster, or with amanually-operated telescopic antenna (aerial).

When your car has a built-in FM/AM antenna (aerial) inthe rear/side glass, see Notes on the control and powersupply leads.

3 To AMP REMOTE IN of an optional poweramplifierThis connection is only for amplifiers. Connecting any othersystem may damage the unit.

4 To the +12 V power terminal which isenergized in the accessory position of theignition switchNotes If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times.Be sure to connect the black ground (earth) lead to ametal surface of the car first.


5 To the +12 V power terminal which is

energized at all timesBe sure to connect the black ground (earth) lead to a metalsurface of the car first.

Remarques sur les cbles de commande et dalimentation Le cble de commande dantenne lectrique (bleu) fournit une

alimentation de + 12 V CC lorsque vous mettez la radio soustension.

Lorsque votre voiture est quipe dune antenne FM/AMintgre dans la vitre arrire/latrale, raccordez le cble decommande dantenne (bleu) ou le cble dalimentation desaccessoires (rouge) la borne dalimentation de lamplificateurdantenne existant. Pour plus de dtail s, consultez votredtaillant.

Une antenne lectrique sans botier de relais ne peut pas treutilise avec cet appareil.

Raccordement pour la conservation de la mmoireLorsque le cble dalimentation jaune est raccord, le circuitde la mmoire est aliment en permanence mme si la cl decontact est sur la position darrt.

Remarques sur le raccordement des haut-parleurs Avant de raccorder les haut-parleurs, mettez lappareil hors

tension. Utilisez des haut-parleurs ayant une impdance de 4 8 ohms

avec une capacit lectrique adquate pour viter de lesendommager.

Ne raccordez pas les bornes du systme de haut-parleurs auchssis de la voiture et ne raccordez pas les bornes du haut-parleur droit celles du haut-parleur gauche.

Ne raccordez pas le cble de mise la masse de cet appareil la borne ngative () du haut-parleur.

Nessayez pas de raccorder les haut-parleurs en parallle. Raccordez uniquement des haut-parleurs passifs. Le

raccordement de haut-parleurs actifs (avec amplificateursintgrs) aux bornes des haut-parleurs peut endommagerlappareil.

Pour viter tout problme de fonctionnement, nutilisez pas lescbles des haut-parleurs intgrs installs dans votre voiture silappareil partage un cble ngatif commun () pour les haut-parleurs droit et gauche.

Ne raccordez pas entre eux les cordons des haut-parleurs delappareil.

Remarque sur le raccordementSi les haut-parleurs ne sont pas raccords correctement, lemessage FAILURE saffiche. Dans ce cas, assurez-vous queles haut-parleurs sont bien raccords.

Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner. When your car has built-in FM/AM antenna (aerial) in the rear/

side glass, connect the power antenna (aerial) control lead(blue) or the accessory power supply lead (red) to the powerterminal of the existing antenna (aerial) booster. For details,consult your dealer.

A power antenna (aerial) without a relay box cannot be usedwith this unit.

Memory hold connectionWhen the yellow power supply lead is connected, power willalways be supplied to the memory circuit even when the ignitionswitch is turned off.

Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of theleft speaker.

Do not connect the ground (earth) lead of this unit to thenegative () terminal of the speaker.

Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers

(with built-in amplifiers) to the speaker terminals may damagethe unit.

To avoid a malfunction, do not use the built-in speaker leadsinstalled in your car if the unit shares a common negative ()lead for the right and left speakers.

Do not connect the units speaker leads to each other.

Note on connectionIf speaker and amplifier are not connected correctly, FAILUREappears in the display. In this case, make sure the speaker andamplifier are connected correctly.


8/468


CDX-GT460U/GT460US

AUDIO OUT REAR*

BUS AUDIO IN

BUS CONTROL IN

A

B

BUS AUDIO IN

BUS CONTROL IN

Source selector*Selector de fuente*

*

XA-C40

*not suppliedno suministrado

*AUDIO OUT SUB/REAR

Connection example

Notes (2-A) Be sure to connect the ground (earth) lead before connecting

the amplifier. The alarm will only sound if the built-in amplifier is used.

Tip (2-B- )For connecting two or more CD/MD changers, the sourceselector XA-C40 (not supp lied) is necessary.

Ejemplo de conexiones

Notas (2-A) Asegrese de conectar primero el cable de conexin a masa

antes de realizar la conexin del amplificador. La alarma sonar nicamente si se utiliza el amplificador

incorporado.

Sugerencia (2-B- )Si desea conectar dos o ms cambiadores de CD/MD,necesitar el selector de fuente XA-C40 (no suministrado).


9/469


L

R

BUS AUDIO IN

AUDIO OUT REAR*2

BUSCONTROL IN

2

4

5

1

3

AUDIO OUTREAR/SUB

BUSINfrom car antenna (aerial)

desde la antena del automvil

*1RCA pin cord (not supplied)*2AUDIO OUT can be switched SUB or

REAR. For details, see the suppliedOperating Instructions.

*1Cable con terminales RCA(no suministrado)

*2AUDIO OUT (Salida de audio) puedecambiarse a SUB (Secundaria) o REAR(Posterior). Para obtener informacin,consulte el manual de instruccionessuministrado.

*1

*2

AMP REM

Max. supply current 0.3 ACorriente mx. de alimentacin de 0,3 A

Fuse (10 A)Fusible (10 A)

Blue/white stripedCon rayas azules y blancas

RedRojo

YellowAmarillo

WhiteBlanco

GreenVerde

PurpleMorado

White/black striped

Con rayas blancas y negras

Grey/black stripedCon rayas grises y negras

Green/black stripedCon rayas verdes y negras

GreyGris

LeftIzquierdo

RightDerecho

LeftIzquierdo

RightDerecho

ANT REM

BlackNegro

BlueAzul

Max. supply current 0.1 ACorriente mx. de alimentacin de 0,1 A

Purple/black stripedCon rayas moradas y negras

Source selector(not supplied)

Selector de fuente(no suministrado)

XA-C40

Supplied with the CD/MD changerSuministrado con el cambiador de CD/MD

*1

Supplied with XA-C40Suministrado con el XA-C40

2

Connection diagram1 To a metal surface of the car

First connect the black ground (earth) lead, then connect theyellow and red power supply leads.

2 To the power antenna (aerial) control lead orpower supply lead of antenna (aerial) boosterNotes It is not necessary to connect this lead if there is no power

antenna (aerial) or antenna (aerial) booster, or with amanually-operated telescopic antenna (aerial).


3 To AMP REMOTE IN of an optional poweramplifierThis connection is only for amplifiers. Connecting any othersystem may damage the unit.

4 To the +12 V power terminal which isenergized in the accessory position of theignition switchNotes If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times.Be sure to connect the black ground (earth) lead to ametal surface of the car first.


5 To the +12 V power terminal which isenergized at all timesBe sure to connect the black ground (earth) lead to a metalsurface of the car first.

Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner. When your car has built-in FM/AM antenna (aerial) in the rear/

side glass, connect the power antenna (aerial) control lead(blue) or the accessory power supply lead (red) to the powerterminal of the existing antenna (aerial) booster. For details,consult your dealer.

A power antenna (aerial) without a relay box cannot be usedwith this unit.

Memory hold connectionWhen the yellow power supply lead is connected, power willalways be supplied to the memory circuit even when the ignitionswitch is turned off.

Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of theleft speaker.

Do not connect the ground (earth) lead of this unit to thenegative () terminal of the speaker.

Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers

(with built-in amplifiers) to the speaker terminals may damagethe unit.

To avoid a malfunction, do not use the built-in speaker leadsinstalled in your car if the unit shares a common negative ()lead for the right and left speakers.

Do not connect the units speaker leads to each other.

Note on connectionIf speaker and amplifier are not connected correctly, FAILUREappears in the display. In this case, make sure the speaker andamplifier are connected correctly.

Diagrama de conexin1 A una superficie metlica del automvil

Conecte primero el cable de conexin a masa negro, ydespus los cables amarillo y rojo de fuente de alimentacin.

2 Al cable de control de la antena motorizadao al cable de fuente de alimentacin delamplificador de seal de la antenaNotas Si no se dispone de antena motorizada ni de amplificador

de antena, o se utiliza una antena telescpica accionadamanualmente, no ser necesario conectar este cable.

Si el automvil incorpora una antena de FM/AM en elcristal trasero o lateral, consulte Notas sobre los cablesde control y de fuente de alimentacin.

3 A AMP REMOTE IN de un amplificador depotencia opcionalEsta conexin es slo para amplificadores. La conexin decualquier otro sistema puede daar la unidad.

4 Al terminal de alimentacin de +12 V querecibe energa en la posicin de accesoriodel interruptor de encendidoNotas Si no hay posicin de accesorio, conctelo al terminal de

alimentacin (batera) de +12 V que recibe energa sininterrupcin.Asegrese de conectar primero el cable de conexin amasa negro a una superficie metlica del automvil.

Si el automvil incorpora una antena de FM/AM en elcristal trasero o lateral, consulte Notas sobre los cables

de control y de fuente de alimentacin.

5 Al terminal de alimentacin de +12 V querecibe energa sin interrupcinAsegrese de conectar primero el cable de conexin a masanegro a una superficie metlica del automvil.

Notas sobre los cables de control y de fuente dealimentacin El cable de control de la antena motorizada (azul) suministrar

cc de + 12 V cuando conecte la alimentacin del sintonizador. Si el automvil dispone de una antena de FM/AM incorporada

en el cristal trasero o lateral, conecte el cable de control deantena motorizada (azul) o el cable de fuente de alimentacinauxiliar (rojo) al terminal de alimentacin del amplificador deantena existente. Para obtener ms informacin, consulte a sudistribuidor.

Con esta unidad no es posible utilizar una antena motorizadasin caja de rel.

Conexin para proteccin de la memoriaSi conecta el cable de fuente de alimentacin amarillo, el circuitode la memoria recibir siempre alimentacin, aunque apague elinterruptor de encendido.

Notas sobre la conexin de los altavoces Antes de conectar los altavoces, desconecte la alimentacin

de la unidad. Utilice altavoces con una impedancia de 4 a 8 con la

capacidad de potencia adecuada para evitar que se daen. No conecte los terminales de altavoz al chasis del automvil,

ni conecte los terminales del altavoz derecho con los delizquierdo.

No conecte el cable de conexin a masa de esta unidad alterminal negativo () del altavoz.

No intente conectar los altavoces en paralelo. Conecte solamente altavoces pasivos. Si conecta altavocesactivos (con amplificadores incorporados) a los terminales dealtavoz, puede daar la unidad.

Para evitar fallas de funcionamiento, no utilice los cables dealtavoz incorporados instalados en el automvil si la unidadcomparte un cable negativo comn () para los altavocesderecho e izquierdo.

No conecte los cables de altavoz de la unidad entre s.

Nota sobre la conexinSi el altavoz no est conectado correctamente, aparecerFAILURE en la pantalla. Si es as, compruebe la conexin delaltavoz.


10/4610


SECTION 2

DISASSEMBLY

Note:This set can be disassemble according to the following sequence.

2-1. SUB PANEL (FL-U) ASSY

(Page 11)

2-2. CD MECHANISM BLOCK(Page 11)

SET

2-3. MAIN BOARD(Page 12)

2-5. CHASSIS (T) SUB ASSY(Page 13)

2-6. ROLLER ARM ASSY(Page 13)

2-7. CHASSIS (OP) ASSY(Page 14)

2-4. SERVO BOARD(Page 12)

1. CHUCKING ARM SUB ASSY(SUPPLEMENT-1 Page 1)

2. SLED MOTOR ASSY(SUPPLEMENT-1 Page 2)

3. OPTICAL PICK-UP SECTION(SUPPLEMENT-1 Page 3)

4. OPTICAL PICK-UP(SUPPLEMENT-1 Page 3)

Ver. 1.2


11/4611


2-2. CD MECHANISM BLOCK

Note:Follow the disassembly procedure in the numerical order given.

2-1. SUB PANEL (FL) ASSY

2 two claws

3 two claws

4sub panel (FL-U) assy

1two screws (+PTT 2.66)

4 CN350

5 CN352 (3P)

3

1 screw(+PTT 2.66)

2 screw(+PTT 2.66)

6 two screws(+PTT 2.64)

7 bracket (CD)8 CD mechanism block


12/4612


2-4. SERVO BOARD

2-3. MAIN BOARD

0 MAIN board

insulating sheet3


8 screw(+PTT 2.610)

7 screw(+P 2.610)

9 heat sink

5 two screws(+P 2.68)



1 three screws(+BTT 2.65)

5 SERVO board

SERVO board

claw

claw

3 toothed lock screw(M 1.72.5)

2 toothed lock screw(M 1.72.5)

1 Remove the eleven solders.

GRYYELBLU

ORGREDBLK

REDWHT

BLKRED

WHT

4 optical pick-up (16 core)(CN1)


13/4613


2-6. ROLLER ARM ASSY

2-5. CHASSIS (T) SUB ASSY

4 chassis (T) sub assy

3 claw

1 two precision screws(+P 1.72.2)

2 two precision screws(+P 1.72.2)

3 washer

4 gear (RA1)

5 roller arm assy

1 spring (RAL)

2 spring (RAR)


14/4614


2-7. CHASSIS (OP) ASSY

Ver. 1.2

7 coil spring (damper) (natural)

8 coil spring (damper) (green)

6chassis (OP) assy

5

1 tension spring (KF)

2 gear (LE1)

3 lever (D)

4 slider (R)


15/4615


SECTION 3DIAGNOSIS FUNCTION

Description of the Diagnostics function:

1. Setting the Diag display modeWith the power off, press the [4]button, [5]button, and [4]button

on the set body or the remote control (for more than 2 seconds)

in turn.

2. Canceling the Diag display modeDuring the Diag function mode, press the [OFF]button.

3. Initial display in the Diag display mode.Just when the Diag mode is entered, reset count is displayed.

The display mode is switched by each rotation of

SEEK +/M> or SEEK /.m keys.

4. Contents of each display mode4-1. Reset count display mode

4-2. Reset count by watchdog timer display mode

4-3. Number of connected units display mode

The display mode is switched by each rotation of [2/GP/ALBM+]or

[1/GP/ALBM--]keys during the number of connected units displaymode.

4-4. Operating hours display mode

Reset count

(in hexadecimal format)Diag code01: Reset count

0 1 X X

Reset count(in hexadecimal format)

Diag code02: Number of resets by watchdog timer

0 2 X X

Show the number of connected units forCD-C, MD-C and XM respectively fromthe rightmost (in hexadecimal format).

Recency of information1-3: 1 represents the latest.

Diag code03: Number of connected unit.

0 3 1 X X X

No. of connected units history 1 (latest) display

No. of connected units history 3 display

No. of connected units history 2 display

0 3 1 X X X

0 3 2 X X X

0 3 3 X X X

Operating hours

(in hexadecimal format)Diag code04: Operating hours

0 4 X X X X

Reset count display

OFFSET/FAILURE error display

CD error information display

Operating hours display

Number of connected units display

Reset count by watchdog timer display

0 1 X X

0 2 X X

0 3 1 X X X

0 4 X X X X

0 5 1 X X

0 6 1 X X X X X

USB error information display

0 7 1 X X


16/4616


4-5. CD error information display mode4-5-1. Error description

4-5-2. Disc type and operating hours


[1/GP/ALBM--]keys during the CD error information display mode.

4-6. OFFSET/FAILURE error display mode


[1/GP/ALBM--] keys during the OFFSET/FAILURE error display

mode.

Error description(in hexadecimalformat)


Diag code05: CD error information

0 5 1 X X

Operating hours


Diag code05: CD error information

0 5 1 X X X X

CD error info history 1 (latest)Error description plus error details display

CD error info history 3

Disc type plus operating hours display

CD error info history 3Error description plus error details display

CD error info history 2Disc type plus operating hours display

CD error info history 2Error description plus error details display

CD error info history 1 (latest)Disc type plus operating hours display

0 5 1 X X X X

0 5 2 X X

0 5 2 X X X X

0 5 3 X X

0 5 3 X X X X

0 5 1 X X

Operating hours


Diag code06: OFFSET/FAILURE

Error description

(0: OFFSET, 1: FAILURE)

0 6 1 X X X X X

OFFSET/FAILURE error history 1 (latest) display

OFFSET/FAILURE error history 3 display

OFFSET/FAILURE error history 2 display

0 6 2 X X X X X

0 6 3 X X X X X

0 6 1 X X X X X

Error information

Indication Description

1X SERVO ERROR3X LOADING ERROR

4X TRACK JUMP

5X TEXT ERROR

FX MECHA ERROR

Disc type

Indication Disc type

0 MP3

1 WMA

2 AAC

3 ATRAC

8 CD/DA

F UNKNOWN

4-7. USB error information display mode4-7-1. Error description

Error description(in hexadecimalformat)


Diag code07: USB error information

0 7 1 X X

Error information

Indication Description

15 DEVICE ERROR

17FILE ERROR

(NO MUSIC)

1E POWER ON ERROR

1F BOOT ERROR

3A INVALID EJECTERROR

43 READ ERROR

44INVALID

FORMAT FILE

FANOT SUPPORT

DEVICE

FBHUB NOT

SUPPORT


17/4617


4-7-2. Disc type and operating hours The display mode is switched by each rotation of [2/GP/ALBM+]or[1/GP/ALBM--]keys during the CD error information display mode.

USB error info history 1 (latest)Error description plus error details display

USB error info history 3Disc type plus operating hours display

USB error info history 3Error description plus error details display



USB error info history 1 (latest)Disc type plus operating hours display

0 7 1 X X X X X

0 7 2 X X

0 7 2 X X X X

0 7 3 X X

0 7 3 X X X X X

0 7 1 X X





0 7 4 X X

0 7 4 X X X X

0 7 5 X X

0 7 5 X X X X

Operating hours


Diag code07: USB error information

0 7 1 X X X X


18/4618


MEMO


19/46


20/46


21/46

21 21CDX-GT41UW/GT410U/GT460U/GT460US


Waveforms

MAIN Board

NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note isprinted in each block.)

For schematic diagrams.Note: All capacitors are inF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

All resistors are inand 1/4W or less unless otherwise

specified. f : internal component.C : panel designation.

For printed wiring boards.Note:X : parts extracted from the component side.Y : parts extracted from the conductor side. a : Through hole.

: Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

A : B+ Line.B : B Line.H : adjustment for repair. Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions. no mark : FM

( ) : AM< > : CD PLAY

: Impossible to measure Voltages are taken with a VOM (Input impedance 10 M).

Voltage variations may be noted due to normal productiontolerances.

Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.

Circled numbers refer to waveforms. Signal path.

J : CD PLAYF : FMf : AML : AUX

Caution:Pattern face side: Parts on the pattern face side seen from the(Side B ) pat te rn face a re ind icated .

Parts face side: Parts on the parts face side seen from the( Si de A) p art s f ac e a re in di ca te d.

Q

C

These are omitted

EB

E

These are omitted

CB

C

These are omitted

BE

0.8 Vp-p

32.768 kHz

1 IC501 i;(XOUT)

1 Vp-p

18.432 MHz

2 IC501 is(OSC IN)

0.2 V/DIV, 20sec/DIV

0.5 V/DIV, 0.1sec/DIV

Note:The components identi-fied by mark0or dottedline with mark0are criti-

cal for safety.Replace only with part

number specified.

Note:Les composants identifis parune marque 0sont critiquespour la scurit.

Ne les remplacer que par unepice portant le numrospcifi.


22/46

2222CDX-GT41UW/GT410U/GT460U/GT460US


: Uses unleaded solder.4-3. PRINTED WIRING BOARD MAIN SECTION

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

L RJ1

(ANTENNA) L R

J652

-1 -2 -3 -4

AUDIO OUTREAR/SUB

BUSAUDIO IN

CN2

CN101

CDMECHANISM

UNIT(MG-101U)

1

3

S501

9K

10K

FREQUENCYSELECT

1

4

8 7

3 2 1

6 5 4

3

4

2

1

1

5

1

7

1

5

X501 S103

RESET

1-872-031- 11

R552

JC38

C890

D153

C951C

820

C704

C705

R673

D503

JC905

IC802

R672

C302

R553JC912

IC401

D802

R815

R814

R813 D801

R816

R818

R890

C812 R8

19

R8

20

Q805C8

14

C808

IC804

R891

JC810

C807

C445

R812

R811

C805

R810

IC681

C804

R809

C802R529

C810

Q3

R351

R570

JC907

L402

L411

JC909

JC910

JC927

JC924

R903

JC923

JC922

JC929

R612R615

R912

C317

JC931

JC930JC928

C7

R917

D105

C329

D107

D106

JC21

D111

D112

JC921

R152

D109

R606

D108

R607

D113

JC926

JC939

C509

JC940R920

R817

JC943

C703

C313

R923

C315

R925

R924

R709

D703

D702

R706

Q702

R708

R

707

D605

D606

D603

D602

R611

L409

R616

JC22

C601

R601

R602

C402

R402

R401

L410

C418

C419

L406

L401

C307

IC6 02

C305

C309

L403

C417

IC601

C415

L405

JC19

R901

R902

JC906

JC941

C301

C325

C516

C330

C304

JC933

C515

JC36

R537

R551

R507

GT460U/GT460U S

GT460U/GT460US

GT460U/GT460U S

GT460U/GT460US

GT41UW/GT410U

GT41UW/GT410U

R538

R523

R534

R557

R544

R556

R545

R546

R559

R520

JC811

JC934

IC801

C702

JC938

JC935

R511

JC33

JC32

R555

R568

C507

C508

C320

R910

C504

R521

R522

C513

C501

C512 C514

R504

R505

R502

R503

C502

R671

R565

R567

R561

L4

R517

Q664

JC16

C510

R519

D502

R674

R563

C519

R569

R636

JC18

JC24

D353R600

D901

JC23

JC903

C312

JC920

JC904

R61

C681

Q420

Q440

C412

C682

D604

D2

Q605

R531

Q491

Q492

R604

R491

JC902

D491

R603

R2

R3R4 R5

R10

C3

C15

C6

L1

R12

R13R6

R7

C8

JC5

D110

CN352

R151

R154

R155

JC932

R153

L151

L901

L902

JC17

R533R532

L407

JC901

JC936

JC913

JC914

R509

JC942

R919

R918

JC12

C816

R558

JC28

C361

C362

C413C414

R357

R358

R355R356

R420

R440

R460

R470

R452

R430

R485

C484 R

451

R431

JC4

JC30

JC29

C443

C426C423

Q432

Q452

C454

C318

R301

JC8

JC14

JC31

R 4 50 R 4 49

C432 C452

R448 R447

R442

R421

R471

R461

Q460

Q470

C434

R462

R472C463

C462

C472 C473

JC9

C444

C424

R540

R510

R526

JC1

R951

R952

C319

R961

R302

C157

D102

D101D

104

D103

C905

C891

C892

C921

C924

JC911

R150

R354

JC11

L501

R913

IC501

R802

R803

R591

L804

L805

R592 R

593

Q401

Q402

JC401

Q411

Q412R411

R493

R916

R915

R914

R403

R404

D152

D151

(CHASSIS)

R926

R927

R536

R550

R595

R596

R597

R598

R599

R156

R157

R158

D156

JC10

R800

C706

C707

D706

D707

JC705

C158

C159

C953

C493

C494

TU1

(TUNER UNIT)

JW1

JW2

JW22

JW23

JW24

JW28

JW34

JW35

JW38

JW42

JW43

JW44

JW45

JW46

JW49

JW50

YEL

JW51

JW52

JW53

JW56

JW57

JW58

JW59

JW60

JW61

JW66

JW68

JW74

JW75

JW76

JW77

JW79

JW95

JW96

JW97

JW98

JW99

JW101

JW102

JW103

JW105

JW106

JW26

JW25

JW33

JW32

JW31

JW36

JW29

JW81

JW80

JW19

JW20

JW21

JW12

JW11

JW10

JW9

JW109

JW108

JW100

JW110

JW17

JW16

JW15

JW14

JW13

JW92

JW91

JW89

JW86

JW83

JW62

JW64

JW63

JW65

JW69

JW84

JW67

JW48

JW47

JW27

JW3

JW4

JW30

JW70

JW71

JW72

JW73

JW78

JW82

JW85

JW87

JW88

JW90

JW104

JW111

JW113

JW114

JW115

JW116

JW119

JW120JW121

JW122

JW123

JW124

JW125

JW126

JW127

JW128

JW129

JW130

JW131

JW132

JW133

JW134

JW135

JW136

JW137

JW138

D607

S103

C803

D304

D303

D308

C623

D30

7

C622

C683

D311

D312

L818

D310

C316

C314

R705

D301

C809

IC803

D302

C403

C401

C701

YEL

C308

C306

C405

C409

C806

C811X50

1

CN350

D309D30

6

D30

5

TH400

X502

L300

L802

L803

C491

CN300

C2

C5

C153

C152

C151

C818

CN370

C364

C363

C365

C366

C486

C485

C431

C451

C461C471

C441

C421

C303

C801

JW18

JW54

JW55

JW118

D804

JW139

C624

C625

C626

C815

JW107

JW5

JW117

JW112

JW94

JW93

CNJ400

CNJ400(BUS CONTROL IN)

IC300

C406

C407

JW140

JW41

JW40

JW39

C819

C600

JW7

F901

R710

CN351

R9

(Page 26)

D2 E-2

D101 I-4

D102 I-4

D103 I-4

D104 I-4

D105 J-7

D106 I-4

D107 I-4

D108 I-3

D109 I-2

D110 I-4

D111 I-4

D112 I-4D113 H-3

D151 I-2

D152 I-2

D153 I-3

D156 I-2

D301 C-8

D302 D-8

D303 C-9

D304 D-9

D305 C-6

D306 C-6

D307 C-6

D308 C-6

D309 C-6

D310 C-6

D311 C-7

D312 C-7

D353 H-8

D491 E-5

D502 H-7

D503 I-6

D602 D-10

D603 D-10

D 60 4 E- 10

D605 D-9

D606 D-9

Semiconductor LocationRef . No. Locat ion Ref . No. Locat ion

D607 D-9

D702 C-8

D703 C-9

D706 C-9

D707 D-8

D 801 F-10

D802 F-9

D804 H-9

D 901 B-10

I C3 00 B -6

I C4 01 D -3

I C5 01 G -6I C6 01 E -1 0

I C6 02 G -7

I C6 81 D -6

I C8 01 I -1 0

I C8 02 H -1 0

I C8 03 G -1 0

I C8 04 H -9

Q3 F-2

Q401 F-4

Q402 E-4

Q411 E-5

Q412 E-4

Q420 B-4

Q432 B-3

Q440 B-4

Q452 C -3

Q460 C -4

Q470 C -4

Q491 E-5

Q492 E-5

Q 60 5 D -1 0

Q664 I-6

Q702 C -8

Q 80 5 G -11


23/46

23 23 CDX-GT41UW/GT410U/GT460U/GT460US


4-4. SCHEMATIC DIAGRAM MAIN SECTION (1/3) Refer to page 28 for IC Block Diagrams.

IC B/D

IC B/D

C701

C303

C600

D606

C622

C306

R301

R302

C623

R604 R603

R706 R708

Q492

C491

R491

R600

R531

JC36

JC905

C626

C625

C624

R599

Q491

C601

JC909

C 70 2 C 70 3

C705

C704

L300

C319 C318

C317

C325

C301

C302

C444 C424 C330

C304

C454 C434

C3 05 C3 07

C309

JC939

JC940

R615

JC31JC30JC29

L902

L901C308

JC12

C312

C320

C314

C313

C316

C315

C681C682C683

IC681IC602

R961

R493 JC8

JC1

R705

R709

R707

R612

R607

R606

JC21

JC 22 R 611

R616 R602

R601

IC300

IC601

JC33 JC32

F901

Q702

Q605

CNJ400

TH400

JC910

JC19

D302

D301

D304

D303D305D306D307D308D309D310D311D312

C706

C707

JC705

CN300

D706

D703

D607

D702

D707

D603 D602

D 60 5 D 604D901

D491

R710

C329

(Page 25)

(Page 24)


24/46



4-5. SCHEMATIC DIAGRAM MAIN SECTION (2/3) Refer to page 28 for IC Block Diagrams.

(Page 23)

(Page 25)

IC B/D

R442R421 R451 R431

C441C421 C451 C431

R10

Q440Q420 Q452 Q432

R447R448 R449 R450

R12 R13

R430

R420

R460

R470

R440

R452

R 35 7 R 35 8

R 35 5 R 3 56

C365

C366

C461

R461

C471

R471

R462R472

C485

R153R155

L1

JC9

JC28

R918

R919

C953

R150

C406

C407

Q401

Q402

Q411

Q460Q470

Q412

C426 C423

C 4 45 C 4 43

C 4 73 C 4 72

C484

JC4

C463 C462

C452 C 432 C413 C414

C905

C362

C361

JC943

C6

C3

C8

C157

JC926

L818

C921

CN352

L805

R152

R151

L151

JC927

C924

JC923

L804

C818

JC928JC930

JC929JC931

R913

J1

R5

R4

R2

R3

C15

JC5

JC11

R354

R920

JC401

R411

R156

R158

R157

R485

J C9 42 J C9 41

C7

R 6 R 7

L4

R558

R61

C151

C153

C152

R154

C820

R912

JC920

J C9 21 J C9 22

R952

R951

JC924

CN370

J652TU1

Q3

C486

IC401

C2

C364

C363

R403

R404

C158

C159

C493

C494

D106

D107

D109

D108

D113

D111

D112

D110

D105

D153

D104

D103

D102

D101

D151

D152D156

C5

D2

R9

JC10

(Page 27)


25/46



4-6. SCHEMATIC DIAGRAM MAIN SECTION (3/3)

Refer to page 21 for Waveforms. Refer to page 29 for IC Block Diagrams. Refer to page 30 for IC Pin Description of IC501.

(Page 23) (Page 24)

IC B/D IC B/D

IC B/D

X502

C409

R351

R502

R401

R402 L401

L410

L403

L407

R551

R557

R511

R510

R532

R534

R553

R567R565

R561

R503

D353

R540

R555

R520

R523

L501

L803

R813

L802

C803 C806

Q805

R811

R812R810

R809

R816

R817

JC901 R901

L411

R925

C891

R552

R591

R592

R593

R927

R595

CN350

R507

R545

S501

JC902

JC903

C415

L406

L405

C892

C804

C402

C419

C412

C507

C508

C510

JC14

C519

C512

C501

C513

R672

JC913

R526

R556

R559 C504R916

R914

R915

R544

JC911

R671

C516C515R521

R522

J C9 32 J C9 33

JC934

R517

JC935

JC936

JC938

JC23

R673

C502

C514 JC16

R 50 5 R 50 4

R596

R598

JC24

JC914

R570

R529

JC912

C509

R674

R519

JC17

R536

JC38

R546

R 8 02 R 8 03

JC811

C815C816

R891

R819R820

C814

R818

C812

JC810

R890

C810

C811

C890

R815R800

JC907R814

C808

C809

C807

C805

IC802IC801

C802C801

R917

R926

CN351

JC18

R636

R563

R 9 23 R 9 24

R533

L402 L409

C418

C401

JC906JC904

R902

R903

C417C405

IC803

R910

R509

X501

S103

Q664

C403

R568

D502

C951

D804

C819

IC804

D802

D801

IC501

R597

D503

R569

R550

R537

R538


26/46



4-7. PRINTED WIRING BOARD KEY SECTION : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13

1-872-032-

1-872-032- (11)

11

1-872-033- (11)

11

1-872-033- (11)

11

(11)

11

LED846,946,S903

SOURCE

M >

SEEK+

LSW901LED861864,LED961963

(RING ILLUMINATION)

LED843,943,S902

SEEK

LSW902

OFF

LED844,944,S904

EQ3

LED845,945,S906

BTM/CAT

1/GP/ALBM 2/GP/ALBM+ 5 6/PAUSE SCRL

PUSH SELECT

(VOLUME)

RE901

AUX

J901

DSPL/DIM

IC971

MODE

LED 847,947,S907

LED 850,950,S908

LED 851,951,S909

LED852,952,S910

LED 853,953,S911

LED854,954,S912

LED855,955,S913

LED 856,956,S914

LED857,957,S915

3/REP 4/SHUF

LED841,941,S901

A

MAIN BOARD CN370

1 2

5 4 3

LED 842,942(CD INDICATOR)

LED944

LED943LED843

LED863

LED961

LED862

LED864

LED846

LED946

LED847

R904

LED947

LED842

LED942

LED850

LED950

LED851L

ED951

LED852

LED845

LED952

S908 S909

S903

S902

LED853L

ED953

LED854

S907

LED945

LED856

LED956

LED857

LED957

LED941LED841

R909

LED861

LED963

LED962

IC971

S906

S904

S910

R854

R954

R947

R847

R961

R861

R862

R843

R943

R906

R907

R908

R902

R903

C974R977

R853

R953

LSW902

S915

LSW901

LED844

S901

S911 S912 S913 S914

LED954

LED855

LED955

1

2

3

4

CN902

ORG

REDFB901

FB903

FB902

BRN

ORG

RED

BRN

R989

C981

R988

C982R901

C992

C975

D906 D953D

904

D903

R971

R888

R889

R887

C976

R978

R984

R983

C979

R850

R950

R910

CN901

Q882Q881 Q883

R911

FB907

FB906C991

R849

R949

R951

R851

R912

R952

R852

R914

R915

R962

R848

R948R946

R846

R845

R945

R944

R844

R905

D971 R976

R975

R864R 863

Q991 Q992

R922

R921

D907

R913

C977

R982

R942 R842

R841

R941

R981

D905

D908 FB904FB905

R993

R994R995

LF901

D951

D955

R881 R882

R886

R883

R885R884IC972

C905

RB901

FL901FLUORESCENT INDICATOR TUBE

CN902

RE901

(Page 22)

LE D844 B -2LE D845 C-2LE D846 B -4LE D847 C-4LE D850 D-5LE D851 D-6LE D852 D-7LE D853 D-8LE D854 D-8LE D855 D-9L ED 85 6 D -1 0L ED 85 7 D -11LE D861 B -3LE D862 B -2

Ref. No. Location

D903 I-10D904 I-9D905 I-10D906 I-10D907 I-10D908 H-9D971 H-4

IC971 D-4IC972 I-11

L ED 84 1 A -13LE D842 B -7LE D843 A -1

Semiconductor LocationRef. No. Location

LE D863 B-3LE D864 C-3L ED 94 1 A -1 3LE D942 B-7LE D943 A-2LE D944 B-2LE D945 C-2LE D946 B-4LE D947 C-4LE D950 D-5LE D951 D-6LE D952 D-7LE D953 D-7LE D954 D-8

Ref . No. Locat ion Ref . No. Locat ion

LE D955 D-9LE D9 56 D -10LE D9 57 D -11LE D961 B -3LE D962 C-3LE D963 C-2

Q881 I-8Q882 I-8Q883 I-9Q991 I-6Q992 I-6


27/46



4-8. SCHEMATIC DIAGRAM KEY SECTION

R989

R988

R901 R904

R978

R984R983

R909

R850R950

R910

Q882

Q881

Q883

R911

R849R949

R 95 1 R 85 1

R912

R 95 2 R 85 2

R 91 4 R 91 5

R954

R962

R961

R943

R948

R946

R945

R9 06 R 907 R 90 8

R944

R 90 2 R 90 3

R977

R976

R975

R913

R982

R953

R981

R881

R886

R883

R885

R884

IC972

R941

R942

R947

R841

R842

R843

R844

R845

R846

R847

R848

R853

R854

R861

R862

FB905

FB904

C905

FB902

FB901

FB903

S901

S902

S903

S904

LSW901(2/2)

LSW902(2/2)

S907

S908

S909

S910

S911

S912

S913

S914

S915

S906

R 92 2 R 92 1

C974C975

C976

C977

C979

C982

C981

Q991Q992

C992 C991

IC971

R971

FB906

FB907

R905

R882

R887

R888

R889

R994

R993

R995

LSW901(1/2)

LSW902(1/2)

R863

R864

FL901RE901

CN901

CN902

J901

LED941

LED942

L ED9 43 L ED8 43

LED945

LED842

LED841

LED944

LED946

LED844

LED947

LED845

LED847

LED846

LED950

LED951

LED952

LED955

LED852

LED954

LED851

LED953

L ED 85 0 L ED 957

LED853

LED956

LED854

L ED 85 5 L ED 96 3

LED962

LED856

LED857

LED961

LED861

LED863

LED862

LED864

D971

D904

D903

D908

D906

D907

D951 D953

D955

LF901

RB901

D905

(Page 24)


28/46


29/4629


IC801 NJM2387ADL3 (MAIN Board (3/3))IC802 NJM2387ADL3 (MAIN Board (3/3))

1 2 3 4 5

CURRENT

LIMIT

THERMAL

PROTECTION

OVERVOLTAGE

PROTECTION

BANDGAP

REFERENCE

VIN CONTROL VOUT VADJ GND

IC803 BD9778HFP (MAIN Board (3/3))

1 2 3 4 5

CURRENT

LIMIT

PWM

COMPARATOR

ERROR

AMP

L:OFF

H:ON

VREF

VIN

TSD

OSC

VIN SW PB GND INV

6

RT

7

EN

VREFSOFT

START

ON/OFF

LATCH

DRIVER

RESET


30/4630


IC PIN DESCRIPTIONIC501 MB90F046PF-G-101E1 (SYSTEM CONTROL) (MAIN BOARD (3/3))

Pin No. Pin Name I/O Pin Description

1 AREASEL0 I Destination setting pin 0

2 AREASEL1 I Destination setting pin 1

3 AREASEL2 I Destination setting pin 24 B-OUTSEL I Black-out with/without discrimination signal input H: Black-out

5 DIAG I Status signal input from power amplifier

6 AAC SEL I AAC play setting signal input

7 BEEP O Beep signal output to power amplifier

8 AMPSTB O Standby signal output to power amplifier

9 VOLATT O Electronic volume attenuate control signal output

10 FSW IN I D/D converter oscillator frequency count signal input

11 VSS Ground pin

12 TUATT O Tuner mute control signal output

13 NSMASK O Noise mask signal output Not used in this set.

14 ILLUMI SEL I Illumination voltage setting signal input

15 COL SEL I Two colors change setting signal input

16, 17 NCO O Not used. (Open)

18 FL CS O Fluorescent indicator tube chip select signal output

19 FL SO O Fluorescent indicator tube serial data signal output

20 FL SCK O Fluorescent indicator tube serial clock signal output


23 VCC5 Power supply pin (+3.3 V)

24 EEP SIO I/O EEPROM bus serial data signal input/output

25 EEP CKO O EEPROM bus serial clock signal output

26 RDS ON O RDS (Radio Data System) on signal output Tuner on: L Not used in this set.27 MC RX I Mechanism microcomputer comunication signal input RX

28 MC TX O Mechanism microcomputer comunication signal output TX


31 RE IN0 I Rotary encoder signal input 0

32 RE IN1 I Rotary encoder signal input 1

33 I2C SCK O I2C bus serial clock signal output

34 I2C SIO I/O I2C bus serial data signal input/output

35 DAVDD A/D converter power supply pin (+3.3 V)

36 AVRH A/D converter external reference power supply pin (+3.3 V)

37 DAVSS Ground pin

38 QUALITY I Noise detect signal input

39 VSM I S-meter voltage detect signal input

40 KEYIN1 I Key signal input 1

41 KEYIN0 I Key signal input 0

42 VSS Ground pin

43 RCIN0 I Rotary commander key signal input Not used in this set.

44 to 47 NCO O Not used. (open)

48 AD ON O A/D converter power supply control signal output

49 MD0 I Operation mode setting pin (Connect to VDD.)

50 MD1 I Operation mode setting pin (Connect to VDD.)

51 MD2 I Operation mode setting pin (Connect to VSS.)

52 KEYACK I Key acknowledgment detect signal input

53 TUATTIN I Tuner mute zero cross detect signal input Not used in this set.

54 BUIN I Back-up power supply detect signal input


31/4631


55 NCO O Not used. (Open)

56 DAVN IRDS (Radio Data System) data block synchronized detect signal input

Not used in this set.


58 UNISI I SONY bus data signal input59 UNISO O SONY bus data signal output

60 UNISCK O SONY bus clock signal output

61 Z MUTE I Mute signal input

62 NOSE SW I Front panel attachment detect signal input L: With panel, H: Without panel

63 FLASH W IMemory mode change signal input Normally H: Single chip mode, after reset

L: flash write mode

64 SIRCS I Remote control signal input

65 to 70 NCO O Not used. (Open)

71 RC IN1 I Rotary commander shift key signal input Not used in this set.

72 to 74 NCO O Not used. (Open)

75 FSW OUT OD/D converter oscillator frequency shift control signal output

L: 350 kHz, H: 415 kHz


77 RESET I CPU reset signal input

78 NCO (OPEN REQ) O Not used. (Open)

79 XIN I Low speed operation clock signal input (32.768 kHz)

80 XOUT O Low speed operation clock signal output (32.768 kHz)

81 VSS1 Ground pin

82 OSCIN I High speed operation clock signal input (18.432 MHz)

83 OSCOUT O High speed operation clock signal output (18.432 MHz)

84 VCC3 Power supply pin (+3.3 V)

85 CYRIL SEL I Cyril correspondence discrimination signal input L: No correspondence

86 DEMOSEL I DEMO select signal input H: DEMO on, L: DEMO off


88 SYSRST O System reset signal output

89 FL ON O Fluorescent indicator tube power on/off control signal output

90 DD ON O D/D converter power on/off control signal output

91 USB OVER I USB overcurrent detection signal input L: Overcurrent detection

92 USB ON O USB overcurrent detection IC control signal output H: On, L: Off

93 WAKE UP O Mechanism microcomputer wake up signal output H: Wake up, L: Sleep

94 CDON I CD mechanism servo power supply control request signal input95 CDMON I CD mechanism deck power supply control request signal input

96 BUSON O Bus on signal output

97 TESTIN I Test mode detect signal input

98 TELATT I Telephone attenuate detect signal input

99 ACC IN I Accessory power supply detect signal input

100 ATT O Audio mute control signal output

Pin No. Pin Name I/O Pin Description


32/4632


SECTION 5

EXPLODED VIEWS

1 X-2149-438-1 PANEL (FL-U) ASSY, SUB

2 3-042-244-11 SCREW (T)

3 X-2108-670-1 LOCK ASSY (S)

4 2-050-124-01 SCREW +BTT 2.6X5

5 A-1215-219-A MAIN BOARD, COMPLETE (GT460U/GT460US)

5 A-1215-247-A MAIN BOARD, COMPLETE (GT41UW/GT410U)

6 2-021-848-01 SHEET (TU), GROUND7 1-833-100-11 CORD (WITH CONNECTOR) (POWER)

(EXCEPT GT460US:IND)

7 1-833-762-11 CONNECTION CORD FOR AUTOMOBILE

(POWER) (for Maruti Suzuki) (GT460US:IND)

F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A

TU1 A-3220-961-B TUNER UNIT (TUX-032)

#1 7-685-792-09 SCREW +PTT 2.6X6 (S)

#2 7-685-790-01 SCREW +PTT 2.6X4 (S)

#3 7-685-793-09 SCREW +PTT 2.6X8 (S)

#4 7-685-794-09 SCREW +PTT 2.6X10 (S)

#5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT#6 7-621-284-40 SCREW +P 2.6X10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

NOTE:

The mechanical parts with no reference

number in the exploded views are not supplied.

Items marked * are not stocked since

they are seldom required for routine service.

Some delay should be anticipated

when ordering these items.

-XX and -X mean standardized parts, so

they may have some difference from the

original one.

Color Indication of Appearance Parts

Example :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinets Color

Accessories are given in the last of this parts list.

Abbreviation

CND : Canadian model

IND : Indian model

5-1. MAIN SECTION

R R

not supplied

not supplied

not supplied

F901

not supplied

TU1

not supplied

not supplied

#1

#1

#1

#3

#4

#4

#5

#6

#3

#4

#2

#1

MG-101U-188//Q

A

A

B

B

1

2

3

4

7

6

A

5

not supplied

The components identified by

mark0or dotted line with mark

0are critical for safety.

Replace only with part number

specified.

Les composants identifis par une

marque0sont critiques pour

la scurit.

Ne les remplacer que par une pice

portant le numro spcifi.

Ver. 1.2


33/4633


51 A-1215-221-A PANEL COMPLETE ASSY, FRONT (GT460US)

51 A-1215-232-A PANEL COMPLETE ASSY, FRONT (GT460U)

51 A-1215-249-A PANEL COMPLETE ASSY, FRONT (GT41UW:US)

51 A-1215-256-A PANEL COMPLETE ASSY, FRONT (GT410U:US)

51 A-1222-410-A PANEL COMPLETE ASSY, FRONT

(GT41UW:CND)

51 A-1222-411-A PANEL COMPLETE ASSY, FRONT

(GT410U:CND)

52 X-2149-756-1 BUTTON ASSY (S) (GT460US)

52 X-2149-757-1 BUTTON ASSY (S) (GT41UW/GT410U/GT460U)53 X-2149-760-1 PANEL (SV) ASSY, FRONT (GT460US)

53 X-2149-761-1 PANEL (SV) ASSY, FRONT (GT460U)

53 X-2149-762-1 PANEL (SV) ASSY, FRONT (GT41UW)

53 X-2149-763-1 PANEL (SV) ASSY, FRONT (GT410U)

54 X-2149-353-1 KNOB (VOL) (SV) ASSY

55 2-693-599-01 SPRING (RELEASE)

56 2-686-937-02 PANEL (FL-U), BACK

57 3-250-543-21 SCREW (+B P-TITE M2)

58 X-2149-228-2 CASE ASSY (for FRONT PANEL) (EXCEPT US)

59 2-686-941-01 HOLDER (USB)

60 X-2176-322-1 CAP (USB) ASSY

61 3-251-320-01 EMBLEM (NO. 2.5), SONY

CN902 1-820-877-11 CONNECTOR, USB (SOCKET) (USB)

FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENT

RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT,VOLUME)


5-2. FRONT PANEL SECTION

58

59FL901CN902

not supplied(KEY board)

not supplied

not supplied

not supplied

not supplied

not suppliednot supplied(AUX board)

51

52

53

60

54

55

56

57

57

RE901

61

Ver. 1.1


34/4634


101 A-1177-168-A MECHANICAL BLOCK ASSY

102 A-1177-169-A DAXEV//Q

0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)

104 2-626-869-01 SCREW (M2X3), SERRATION

105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN

106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK

107 A-1206-357-A SERVO BOARD, COMPLETE

#7 7-627-000-08 SCREW, PRECISION +P 1.7X2.2 TYPE3


5-3. CD MECHANISM SECTION(MG-101U-188//Q)

NOTE:Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.

not supplied

#7#7

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

101

102

103

105

104

107

106not supplied106

Ver. 1.2


35/4635


SECTION 6

ELECTRICAL PARTS LIST

AUX BOARD

**********

< FERRITE BEAD >

FB901 1-414-595-11 INDUCTOR, FERRITE BEAD



< JACK >

J901 1-819-732-21 JACK (DIA. 3.5) (AUX)

*************************************************************

KEY BOARD

**********

< CAPACITOR >

C905 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC974 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C975 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V








< CONNECTOR >

CN901 1-820-620-11 PLUG, CONNECTOR 24P

< DIODE >

D903 8-719-057-80 DIODE MA8180-M-TX

D904 8-719-057-80 DIODE MA8180-M-TX

D905 8-719-977-12 DIODE DTZ6.8B

D906 8-719-977-12 DIODE DTZ6.8B

D907 8-719-977-12 DIODE DTZ6.8B

D908 8-719-977-12 DIODE DTZ6.8B

D951 1-804-988-21 VARISTOR, CHIP (1608)

D953 1-804-988-21 VARISTOR, CHIP (1608)

D955 1-804-988-21 VARISTOR, CHIP (1608)

D971 8-719-420-90 DIODE MA8051-M

< FERRITE BEAD >



FB906 1-216-295-11 SHORT CHIP 0

FB907 1-216-295-11 SHORT CHIP 0

< FLUORESCENT INDICATOR TUBE >

FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENT

< IC >

IC971 6-600-163-01 IC RS-770 (IR)

IC972 6-706-715-01 IC NJM2867F33(TE2)

< DIODE >

LED841 8-719-078-21 LED SML-310PTT86 (Z)

LED842 8-719-078-21 LED SML-310PTT86 (CD INDICATOR)

LED843 8-719-078-21 LED SML-310PTT86 (OFF)

LED844 8-719-078-21 LED SML-310PTT86 (EQ3)

LED845 8-719-078-21 LED SML-310PTT86 (BTM/CAT)

LED846 8-719-078-21 LED SML-310PTT86 (SOURCE)

LED847 8-719-078-21 LED SML-310PTT86 (MODE)

LED850 8-719-078-21 LED SML-310PTT86 (DSPL/DIM)

LED851 8-719-078-21 LED SML-310PTT86 (1/GP/ALBM )

LED852 8-719-078-21 LED SML-310PTT86 (2/GP/ALBM +)

LED853 8-719-078-21 LED SML-310PTT86 (3/REP)

LED854 8-719-078-21 LED SML-310PTT86 (4/SHUF)

LED855 8-719-078-21 LED SML-310PTT86 (5)

LED856 8-719-078-21 LED SML-310PTT86 (6/PAUSE)

LED857 8-719-078-21 LED SML-310PTT86 (SCRL)

LED861 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)

LED862 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)

LED863 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED864 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)

LED941 8-719-053-09 LED SML-310VTT86 (Z)

LED942 8-719-053-09 LED SML-310VTT86 (CD INDICATOR)

LED943 8-719-053-09 LED SML-310VTT86 (OFF)

LED944 8-719-053-09 LED SML-310VTT86 (EQ3)

LED945 8-719-053-09 LED SML-310VTT86 (BTM/CAT)

LED946 8-719-053-09 LED SML-310VTT86 (SOURCE)

LED947 8-719-053-09 LED SML-310VTT86 (MODE)

LED950 8-719-053-09 LED SML-310VTT86 (DSPL/DIM)

LED951 8-719-053-09 LED SML-310VTT86 (1/GP/ALBM )

LED952 8-719-053-09 LED SML-310VTT86 (2/GP/ALBM +)

LED953 8-719-053-09 LED SML-310VTT86 (3/REP)

LED954 8-719-053-09 LED SML-310VTT86 (4/SHUF)

LED955 8-719-053-09 LED SML-310VTT86 (5)

LED956 8-719-053-09 LED SML-310VTT86 (6/PAUSE)


NOTE:

Due to standardization, replacements in

the parts list may be different from the

parts specified in the diagrams or the

components used on the set.

-XX and -X mean standardized parts, so

they may have some difference from the

original one.

RESISTORS

All resistors are in ohms.

METAL:Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F:nonflammable

Items marked * are not stocked since

they are seldom required for routine service.

Some delay should be anticipated

when ordering these items.

SEMICONDUCTORS

In each case, u : , for example:

uA.. : A.. uPA.. : PA..

uPB.. : PB.. uPC.. : PC.. uPD.. : PD..

CAPACITORS

uF : F

COILS

uH : H

Abbreviation

CND : Canadian model

IND : Indian model

KEYAUX

The components identified by

mark0or dotted line with mark

0are critical for safety.

Replace only with part number

specified.

Les composants identifis par une

marque0sont critiques pour

la scurit.

Ne les remplacer que par une pice

portant le numro spcifi.

When indicating parts by reference

number, please include the board.

Ver. 1.1


36/4636


LED957 8-719-053-09 LED SML-310VTT86 (SCRL)

LED961 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)



< COIL >

LF901 1-457-223-11 COIL, COMMON MODE CHOKE

< SWITCH >

LSW901 1-798-018-11 SWITCH, TACTILE (WITH LED)

(M>SEEK+)

LSW902 1-798-018-11 SWITCH, TACTILE (WITH LED)

(.mSEEK)

< TRANSISTOR >

Q881 8-729-600-22 TRANSISTOR 2SA1235-F

Q882 8-729-600-22 TRANSISTOR 2SA1235-F

Q883 8-729-600-22 TRANSISTOR 2SA1235-F

Q991 6-550-752-01 TRANSISTOR DTC614TKT146Q992 6-550-752-01 TRANSISTOR DTC614TKT146

< RESISTOR >

R841 1-216-810-11 METAL CHIP 120 5% 1/10W

R842 1-216-810-11 METAL CHIP 120 5% 1/10W

R843 1-216-811-11 METAL CHIP 150 5% 1/10W

R844 1-216-810-11 METAL CHIP 120 5% 1/10W

R845 1-216-811-11 METAL CHIP 150 5% 1/10W

R846 1-216-810-11 METAL CHIP 120 5% 1/10W

R847 1-216-811-11 METAL CHIP 150 5% 1/10W

R848 1-216-810-11 METAL CHIP 120 5% 1/10W

R849 1-216-807-11 METAL CHIP 68 5% 1/10W

R850 1-216-807-11 METAL CHIP 68 5% 1/10W

R851 1-216-807-11 METAL CHIP 68 5% 1/10W

R852 1-216-807-11 METAL CHIP 68 5% 1/10W

R853 1-216-811-11 METAL CHIP 150 5% 1/10W

R854 1-216-810-11 METAL CHIP 120 5% 1/10W

R861 1-216-811-11 METAL CHIP 150 5% 1/10W

R862 1-216-810-11 METAL CHIP 120 5% 1/10W

R863 1-216-811-11 METAL CHIP 150 5% 1/10W

R864 1-216-810-11 METAL CHIP 120 5% 1/10W

R881 1-216-821-11 METAL CHIP 1K 5% 1/10W

R882 1-216-821-11 METAL CHIP 1K 5% 1/10W

R883 1-216-821-11 METAL CHIP 1K 5% 1/10W

R884 1-216-833-11 METAL CHIP 10K 5% 1/10W

R885 1-216-833-11 METAL CHIP 10K 5% 1/10W

R886 1-216-833-11 METAL CHIP 10K 5% 1/10W

R887 1-216-845-11 METAL CHIP 100K 5% 1/10W

R888 1-216-845-11 METAL CHIP 100K 5% 1/10W

R889 1-216-845-11 METAL CHIP 100K 5% 1/10W

R901 1-216-820-11 METAL CHIP 820 5% 1/10W

R902 1-216-821-11 METAL CHIP 1K 5% 1/10W

R903 1-216-821-11 METAL CHIP 1K 5% 1/10W

R904 1-216-822-11 METAL CHIP 1.2K 5% 1/10W

R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R906 1-216-820-11 METAL CHIP 820 5% 1/10W

R907 1-216-821-11 METAL CHIP 1K 5% 1/10WR908 1-216-821-11 METAL CHIP 1K 5% 1/10W

R909 1-216-822-11 METAL CHIP 1.2K 5% 1/10W

R910 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R911 1-216-824-11 METAL CHIP 1.8K 5% 1/10W

R912 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R913 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R914 1-216-828-11 METAL CHIP 3.9K 5% 1/10W

R915 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR921 1-216-295-11 SHORT CHIP 0

R922 1-216-295-11 SHORT CHIP 0

R941 1-216-813-11 METAL CHIP 220 5% 1/10W

R942 1-216-813-11 METAL CHIP 220 5% 1/10W

R943 1-216-812-11 METAL CHIP 180 5% 1/10W

R944 1-216-811-11 METAL CHIP 150 5% 1/10W

R945 1-216-812-11 METAL CHIP 180 5% 1/10W

R946 1-216-811-11 METAL CHIP 150 5% 1/10W

R947 1-216-812-11 METAL CHIP 180 5% 1/10W

R948 1-216-811-11 METAL CHIP 150 5% 1/10W

R949 1-216-809-11 METAL CHIP 100 5% 1/10W

R950 1-216-809-11 METAL CHIP 100 5% 1/10W

R951 1-216-809-11 METAL CHIP 100 5% 1/10WR952 1-216-809-11 METAL CHIP 100 5% 1/10W

R953 1-216-812-11 METAL CHIP 180 5% 1/10W

R954 1-216-811-11 METAL CHIP 150 5% 1/10W

R961 1-216-809-11 METAL CHIP 100 5% 1/10W

R962 1-216-809-11 METAL CHIP 100 5% 1/10W

R971 1-216-809-11 METAL CHIP 100 5% 1/10W

R975 1-216-811-11 METAL CHIP 150 5% 1/10W

R976 1-216-811-11 METAL CHIP 150 5% 1/10W

R977 1-216-809-11 METAL CHIP 100 5% 1/10W

R978 1-216-864-11 SHORT CHIP 0

R981 1-218-893-11 METAL CHIP 82K 0.5% 1/10W

R982 1-216-841-11 METAL CHIP 47K 5% 1/10W

R983 1-216-801-11 METAL CHIP 22 5% 1/10W

R984 1-216-801-11 METAL CHIP 22 5% 1/10W

R988 1-216-864-11 SHORT CHIP 0

R989 1-216-845-11 METAL CHIP 100K 5% 1/10W

R993 1-216-809-11 METAL CHIP 100 5% 1/10W

R994 1-216-809-11 METAL CHIP 100 5% 1/10W

R995 1-216-809-11 METAL CHIP 100 5% 1/10W

< NETWORK RESISTOR >

RB901 1-239-662-81 RESISTOR, NETWORK 10X2

< ROTARY ENCODER >

RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT,VOLUME)

< SWITCH >

S901 1-786-653-21 SWITCH, TACTILE (Z)

S902 1-786-653-21 SWITCH, TACTILE (OFF)

S903 1-786-653-21 SWITCH, TACTILE (SOURCE)

S904 1-786-653-21 SWITCH, TACTILE (EQ3)

S906 1-786-653-21 SWITCH, TACTILE (BTM/CAT)

S907 1-786-653-21 SWITCH, TACTILE (MODE)

S908 1-786-653-21 SWITCH, TACTILE (DSPL/DIM)

S909 1-786-653-21 SWITCH, TACTILE (1/GP/ALBM )

S910 1-786-653-21 SWITCH, TACTILE (2/GP/ALBM +)S911 1-786-653-21 SWITCH, TACTILE (3/REP)

S912 1-786-653-21 SWITCH, TACTILE (4/SHUF)


KEY


37/4637


S913 1-786-653-21 SWITCH, TACTILE (5)

S914 1-786-653-21 SWITCH, TACTILE (6/PAUSE)

S915 1-786-653-21 SWITCH, TACTILE (SCRL)

*************************************************************

A-1215-219-A MAIN BOARD, COMPLETE (GT460U/GT460US)

A-1215-247-A MAIN BOARD, COMPLETE (GT41UW/GT410U)*********************

7-621-284-40 SCREW +P 2.6X10

7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT

7-685-794-09 SCREW +PTT 2.6X10 (S)

< CAPACITOR >

C2 1-126-947-11 ELECT 47uF 20% 35V


C5 1-124-589-11 ELECT 47uF 20% 16V




C151 1-126-960-11 ELECT 1uF 20% 50V

C152 1-126-960-11 ELECT 1uF 20% 50V

C153 1-126-961-11 ELECT 2.2uF 20% 50V






C303 1-128-551-11 ELECT 22uF 20% 63V



C306 1-124-233-11 ELECT 10uF 20% 16V


C308 1-124-233-11 ELECT 10uF 20% 16V




C314 1-124-233-11 ELECT 10uF 20% 16V


C316 1-124-233-11 ELECT 10uF 20% 16V


C318 1-162-923-11 CERAMIC CHIP 47PF 5% 50V








C363 1-126-160-11 ELECT 1uF 20% 50V

C364 1-126-160-11 ELECT 1uF 20% 50V

C365 1-126-960-11 ELECT 1uF 20% 50V

C366 1-126-960-11 ELECT 1uF 20% 50V

C401 1-124-234-00 ELECT 22uF 20% 16V


C403 1-124-584-00 ELECT 100uF 20% 10VC405 1-124-234-00 ELECT 22uF 20% 16V

C406 1-124-257-00 ELECT 2.2uF 20% 50V

C407 1-124-257-00 ELECT 2.2uF 20% 50V

C409 1-124-233-11 ELECT 10uF 20% 16V







C421 1-126-964-11 ELECT 10uF 20% 50V

C423 1-165-908-11 CERAMIC CHIP 1uF 10% 10V



C431 1-126-964-11 ELECT 10uF 20% 50V



C441 1-126-964-11 ELECT 10uF 20% 50V


C444 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC445 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C451 1-126-964-11 ELECT 10uF 20% 50V



C461 1-126-964-11 ELECT 10uF 20% 50V



C471 1-126-964-11 ELECT 10uF 20% 50V




C485 1-126-933-11 ELECT 100uF 20% 16V

C486 1-126-964-11 ELECT 10uF 20% 50V

C491 1-124-589-11 ELECT 47uF 20% 16V
















C600 1-126-935-11 ELECT 470uF 20% 16V


C622 1-126-924-11 ELECT 330uF 20% 10V

C623 1-126-916-11 ELECT 1000uF 20% 6.3V

C624 1-124-584-00 ELECT 100uF 20% 10V

C625 1-124-584-00 ELECT 100uF 20% 10V

C626 1-124-584-00 ELECT 100uF 20% 10V



C683 1-124-584-00 ELECT 100uF 20% 10V


MAINKEY


38/4638


C701 1-131-868-81 ELECT 3300uF 20% 16V

C702 1-164-005-11 CERAMIC CHIP 0.47uF 25V

C703 1-164-005-11 CERAMIC CHIP 0.47uF 25V




C801 1-126-933-11 ELECT 100uF 20% 16V


C803 1-124-589-11 ELECT 47uF 20% 16V



C806 1-124-589-11 ELECT 47uF 20% 16V



C809 1-126-933-11 ELECT 100uF 20% 16V


C811 1-124-584-00 ELECT 100uF 20% 10V


C815 1-126-933-11 ELECT 100uF 20% 16V

sony cdx gt460us fm am

Documents