span guideline
TRANSCRIPT
Updated 01-02-2013
1
GUIDELINES FOR LISTING AND REGISTRATION OF SUPPLIERS UNDER
SECTION 180(m) WATER SERVICES INDUSTRY ACT 2006
1. INTRODUCTION
Any supplier who wishes to supply equipment, device, material, system or
facility (collectively called as product) for water supply and sewerage system
in Peninsular Malaysia, Wilayah-Wilayah Persekutuan Putrajaya and Labuan
is required to be listed or registered with SPAN prior to carrying out such
activities.
2. DEFINITION
For this purpose, a supplier refers to company incorporated in Malaysia (sole
proprietorship, partnership, limited partnership or corporation) that has been
established to offer goods and/or services.
3. PRODUCT CATEGORY
Registration of supplier will be classified in accordance to two (2) main
product categories as listed below:
Category A -
-
Products that can undergo full certification to any SPAN
recognised standards/specifications from any
Certification Bodies recognised by SPAN. Products under this category and the respective
approved standards are listed in Appendix I.
Updated 01-02-2013
2
4. APPLICATION FOR LISTING/REGISTRATION OF SUPPLIER
4.1 Application
Effective 6 February 2013, application for listing or registration of suppliers for
products under category A and category B shall be made via on-line supplier
e-registration at SPAN website.
4.2 Certificate of Conformity Application for products in category A shall be accompanied with a copy of
certificate of conformity issued by SPAN recognised certification bodies to
show that product has complied with product standard.
4.3 Certification Body
SPAN only recognises certificates produced by certification bodies which are
accredited by Standard Malaysia under the Accreditation of Certification
Bodies (ACB) Scheme and other international certification bodies recognised
by Standard Malaysia through the Pacific Accreditation Cooperation (PAC)
Category B -
-
Products without any specific standards/specifications or
product with standards for test compliance that can
undergo performance testing by any accredited test
laboratory recognised by SPAN.
Products under this category and the respective
approved testing standards/requirements are listed in
Appendix II.
Updated 01-02-2013
3
and International Accreditation Forum (IAF) Multilateral Recognition
Arrangement (MRA).
List of accredited certification bodies recognised by SPAN can be referred to
at Standard Malaysia website at www.standardmalaysia.gov.my or at
www.apec-pac.org for certification bodies under the PAC MRA as well as at
www.iaf.nu for certification bodies under the IAF MRA.
4.4 Test Report
Application for products under category B shall be accompanied with test
report to show compliance to the testing standard/requirements (e.g.
performance requirement of a product) as determined in Appendix II. Test
report to be submitted for this purpose shall be the original copy and is written
either in English or Bahasa Malaysia. Report in other languages shall be
translated into either in English or Bahasa Malaysia before the submission to
SPAN.
4.5 Testing Laboratory
SPAN only accepts testing report produced by testing laboratories which are
accreditated by Standard Malaysia under the SAMM scheme and other
international testing laboratories recognised by Standard Malaysia through the
International Laboratory Accreditation Cooperation (ILAC) Mutual Recognition
Arrangement (MRA) and International Accreditation Forum (IAF) Multilateral
Recognition Arrangement (MLA). List of accredited testing laboratories can
be referred to at Standard Malaysia website.
Updated 01-02-2013
4
4.6 Certified True Copy of Certificate
Copy of certificates (e.g. product certificate, HALAL certificate) shall be
certified as a true copy by any of the following bodies:
(i) the certification body that produces the certificate
(ii) Commission of Oath
5. APPROVAL FOR LISTING OF SUPPLIER AND PRODUCT UNDER CATEGORY A
5.1 Listing of Supplier
Any application under category A which has been approved will be listed in
the “Listing of Supplier” at SPAN website.
5.2 Confirmation Letter
Confirmation letter to confirm the listing will be issued to the supplier.
5.3 Responsibilities of Supplier
All listed supplier under this category shall be responsible to ensure his
product certificate is continuously maintained and valid throughout the listing
period.
Updated 01-02-2013
5
5.4 Maintaining Supplier’s name in the Listing
Any listed supplier under this category is required to submit a copy of
renewed product certificate on yearly basis in order to maintain his company
and his product in the listing. Failing to comply with these requirements may
lead to an automatic delisting of the supplier without prior notice.
6. APPROVAL FOR REGISTRATION OF SUPPLIER AND PRODUCT UNDER CATEGORY B
6.1 Certificate of Registration
Any application under category B which has been approved will be given a
Certificate of Registration.
6.2 Validity of a Registration Certificate
The validity period of certificate of registration will be determine by SPAN and
shall be valid for a period of not less than one year and not more than three
years from the date of issuance.
6.3 Listing at the SPAN website
The approved supplier will be listed in the “List of Registered Supplier” at
SPAN website.
Updated 01-02-2013
6
6.4 Responsibilities of a Registered Supplier
All registered supplier are responsible to adhere to all approval conditions as
listed in the certificate of registration. Failing to comply with any of the
conditions may lead to termination of registration.
6.5 Renewal of Certificate
Every application for renewal of certificate shall be made online not later than
three months before the end of the expiry date.
7. PROCESSING TIME
7.1 Product Category A
When a completed application is received by SPAN, the processing time for
listing of supplier at SPAN website and issuing confirmation letter will be
completed within 3 working days.
7.2 Product Category B
For application which does not involve pilot project, certificate of registration
will be issued to the approved supplier within 21 working days.
8. FEE
No fees are imposed for the application of listing or registration of supplier at
this moment.
Updated 01-02-2013
7
9. USE OF SPAN LOGO
Use of SPAN logo is allowed for marketing purpose on product catalogue in
the form of hard and electronic media and subject to the following conditions:
(i) the logo cannot be printed on product to be supplied;
(ii) the logo must be printed with listing or registration number; and
(iii) SPAN logo cannot not be defaced, obstructed, misused, forged,
falsified or altered.
Please refer to “Garis Panduan Penggunaan Logo SPAN” for details
description on how to use SPAN logo.
10. FURTHER INFORMATION
For any further information about listing and registration of suppliers, please
contact the department of Research, Development and Innovation of SPAN at
the following contact number: 03 – 83179333/334/335 and speak to any of the
following officer: Bazlan Mohd Noor (ext. 374)/ Natasha Khairuddin (ext. 218)
/ Zaidah Hassan (ext.219).
11. OFFENCE FOR GIVING FALSE OR MISLEADING INFORMATION
SPAN wish to highlight that it is an offence under Section 130 of the Water
Services Industry Act 2006 for “a person who discloses or provides
information to the Commission or its authorized officers that he knows or has
reason to believe is false or misleading commits an offence and shall, on
conviction, be liable to a fine not exceeding two hundred thousand ringgit or to
imprisonment for a term not exceeding two years or to both.”
Research, Development and Innovation Division Feb 2012
Updated 01-02-2013
i
APPENDIX I
(1) Water supply products under Category A and the respective approved standards
Items Standard Number Standard Title
(a) Water Pipes
Polyethylene (PE) Pipes
MS 1058: Part 2: 2005 Specification for Polyethylene (PE) Piping Systems for Water Supply :
Part 2 : Pipes (Forth Revision)
ISO 4427–2 : 2007 Plastics Piping Systems –
Polyethylene (PE) Pipes and Fittings for Water Supply – Part 2 : Pipes
DIN 8075 (1999 – 08) Polyehtylene (PE) Pipes – General quality requirements, testing.
PE-RT Pipes ISO 22391: Part 2: 2007
Plastics Piping Systems for Hot and Cold Water Installations –
Polyethylene of Raised Temperature Resistance (PE-RT) : Part 2 : Pipes
PE-RT/AL/PE-RT Pipes
BS EN ISO 21003 -1: 2008
Multilayer Piping Systems for Hot and Cold Water Installation Inside
Buildings. General
PE-X Pipes MS 1736 : Part 2 : 2004
Plastic Piping Systems for Hot and Cold Water Installations –
Crosslinked Polyethylene (PE-X): Part 2 : Pipes (ISO 15875-2:2002
MOD)
PE Aluminium (PE-AL-PE)
Pipes ASTM F1282 – 03
Standard Specification for Polyethylene / Aluminium /
Polyethylene (PE-AL-PE) Composite Pressure Pipes
Unplasticized Polyvinylchloride
(uPVC) Pipes
MS 628: Part 1: 1999 AMD.1: 2001 & AMD.2:
2002
Specification for Unplasticised PVC (uPVC) Pipes for Water Supply :
Part 1: Pipes (1st revision)
BS EN ISO 1452-2: 2009
Plastics Piping Systems for Water Supply and for Buried and Above-Ground Drainage and Sewerage Under Pressure. Unplasticized
Poly(vinyl Chloride) (PVC U). Pipes
Updated 01-02-2013
ii
Items Standard Number Standard Title
Chlorinated Polyvinylchloride
(cPVC) Pipes
MS 2045 : 2007 Chlorinated Poly (Vinyl Chloride)
(PVC-C) Plastic Hot-and-Cold-Water Distribution Systems – Specification.
ASTM D2846 / D2846M – 09b
Standard Specification for Chlorinated Polyvinyl Chloride
(cPVC) Plastic Hot and Cold Water Distribution System.
MS 1757 : Part 1 : 2008
Chlorinated Poly (Vinyl Chloride) (PVC-C) – Plastic Piping System – Part 1 : Specification for Schedule
40 & 80 Pipes.
Acrylonitrile-Butadiene-
Styrene (ABS) Pipes
MS 1419: Part 1: 2007
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for Pressure Applications – Part 1: Specification for Compounds, Pipes and Fittings
(First Revision)
AS/NZS 3518 : 2004 Acrylonitrile Butadiene Styrene (ABS) Compounds, Pipes and
Fittings for Pressure Application.
Polypropylene (PP) Pipes
ISO 15874: Part 2: 2003
Plastics Piping Systems for Hot and Cold Water Installations –
Polypropylene (PP). Part 2: Pipes
DIN 8078: 2008 Polypropylene (PP) Pipes – PP-H, PP-B, PP-R, PP-RCT – General
Quality Requirements and Testing
Polybutylene (PB) Pipes
AS/NZS 2642-2: 2008 Polybutylene (PB) Plumbing Pipe Systems – Polybutylene (PB) Pipe
for Hot and Cold Water Applications.
MS ISO 15876-2 : 2004, AMD. 1: 2009
Plastics Piping Systems for Hot and Cold Water Installations –
Polybutylene (PB) Part 2 : Pipes (ISO 15876-2:2003, MOD)
Glass Reinforced Plastic (GRP)
Pipes ISO 10639: 2004
Plastics Piping System for Pressure and Non-pressure Water Supply – Glass Reinforced Thermosetting
Plastics (GRP) Systems Based On Unsaturated Polyester (UP) Resin
Filament-Wounded
Fibreglass Pipes
ASTM D 2996-01 : 2007
Standard Specification for Filament-Wound “Fibreglass” (Glass-Fiber-
Thermosetting-Resin) Pipe
Updated 01-02-2013
iii
Items Standard Number Standard Title
Steel Pipes
BS 534: 1990 Steel Pipes, Joints and Specials for Water and Sewage
MS 1968 : 2007
Non-Alloy Steel Tubes and Fittings for the Conveyance of Aqueous
Liquids Including Water for Human Consumption – Technical Delivery
Conditions
BS EN 10224 : 2002
Non-Alloy Steel Tubes and Fittings for the Conveyance of Aqueous
Liquids Including Water for Human Consumption – Technical Delivery
Conditions
Stainless Steel (SS) Pipes -
Industrial
MS 1841: 2010 Seamless, Welded and Heavily Cold
Austenitic Stainless Steel Pipes - Specification
ASTM A312/A312M-11
Standard Specification for Seamless, Welded, and Heavily
Cold Worked Austenitic Stainless Steel Pipes
Stainless Steel (SS) Light Gauge
Tubes
MS 1988: 2007
Welded Stainless Steel Tubes for the Conveyance of Water and Other
Aqueous Liquids – Technical Delivery Conditions
BS EN 10312 : 2002
Welded Stainless Steel Tubes for the Conveyance of Aqueous Liquids
Including Water for Human Consumption. Technical Delivery
Conditions
JIS G 3448: 2004 Light Gauge Stainless Steel Pipes for Ordinary Piping
Ductile Iron (DI) Pipes
MS 1919: 2006
Ductile Iron Pipes, Fittings, Accessories and Their Joints for
Water Pipelines – Requirement and Test Method
BS EN 545 : 2010
Ductile Iron Pipes, Fittings, Accessories and Their Joints for
Water Pipelines – Requirement and Test Method
Copper Tubes BS EN 1057: 1996
Copper and Copper Alloys. Seamless, Round Copper Tubes for
Water and Gas in Sanitary and Heating Applications
Updated 01-02-2013
iv
Items Standard Number Standard Title
Steel Pipe with Plastic Lining CJ/T 137: 2001 Steel Pipes of Lining Plastic for
Water Supply
(b) Water fittings
Polyethylene (PE) Fittings
BS EN 12201-3:2003 Polyethylene Pipes for Water Supply. Part 3 : Fittings
MS 1058: Part 3: 2006 Polyethylene (PE) Piping Systems for Water Supply – Part 3 : Fittings
AS/NZS 4129: 2008 Fittings for Polyethylene (PE) Pipes for Pressure Applications.
HDPE Joints Assemblies and
Fittings
DIN 16963 : Part 5 : (1999-10)
Pipe Joints and Components of Polyethylene (PE) for Pipes Under Pressure, PE 80 and PE 100 – Part 5 : General Quality Requirements,
Testing.
PE-X Fittings MS 1736 : Part 3 : 2004
Plastics Piping Systems for Hot and Cold Water Installations –
Crosslinked Polyethylene (PE-X): Part 3 : Fittings
PE-RT Fittings ISO 22391 – 3 : 2007
Plastics piping systems for hot and cold water installations –
Polyethylene of raised temperature resistance (PE-RT) – Part 3 :
Fittings
PE-RT/AL/PE-RT Fittings ISO 21003 – 3 : 2008
Multilayer piping systems for hot and cold water installations inside
buildings – Part 3 : Fittings
PPO Fittings ISO 4176 : 1994
Polyethylene/aluminium and cross-linked polyethylene/aluminium
macro-composite pipe systems for pressure applications
Nylon Joints and Compression
Fittings for use with HDPE Pipes
BS 5114: 1975 (1981) Amd.2 – 1987
Specification for Performance Requirements for Joints and
Compression Fittings for Use with Polyethylene Pipes
ISO 14236: 2000
Plastics Pipes and Fittings – Mechanical-Joint Compression
Fittings for Use with Polyethylene Pressure Pipes in Water Supply
Systems.
Polypropylene (PP) Fittings
ISO 15874: Part 3: 2003
Plastics Piping Systems for Hot and Cold Water Installations –
Polypropylene (PP) – Part 3 : Fittings
Updated 01-02-2013
v
Items Standard Number Standard Title
DIN 16962-5: 2000
Pipe Joints and Elements for Polypropylene (PP) for Pipes Under Pressure, PP-H 100, PP-B 80 and PP-R 80 – Part 5: General Quality
Requirements, Testing.
Polybutylene (PB) Fittings
AS/NZS 2642-3: 2008
Polybutylene (PB) Plumbing Pipe Systems – Mechanical Jointing
Fittings for Use with Polybutylene (PB) Pipes for Hot and Cold Water
Applications
MS ISO 15876 – 3 : 2004
Plastics Piping Systems for Hot and Cold Water Installations –
Polybutylene (PB) Part 3 : Fittings
Unplasticized Polyvinylchloride (uPVC) Joints /
Fittings
MS 628: Part 2: Section 2.1: 1999
Specification for Unplasticised PVC (uPVC) Pipes for Water Supply : Part 2: Joints and Fittings for Use
with uPVC Pipes: Section 2.1: uPVC Joints and Fittings
BS EN ISO: 1452-3: 2009
Plastics Piping Systems for Water Supply and for Buried and Above-Ground Drainage and Sewerage Under Pressure. Unplasticized Poly(vinyl Chloride) (PVC U).
Fittings.
BS 4346-1: 1969
Joints and Fittings for use with Unplasticized PVC Pressure Pipes.
Injection Moulded Unplasticized PVC Fittings for Solvent Welding for use with Pressure Pipes, Including
Potable Water Supply.
BS 4346-2: 1970
Joints and Fittings for use with Unplastisized PVC Pressure Pipes.
Mechanical Joints and Fittings, Principally of Unplasticized PVC.
Chlorinated Polyvinylchloride (uPVC) Fittings
ASTM D2846 / D2846M – 09b
Standard Specification for Chlorinated Polyvinyl Chloride
(cPVC) Plastic Hot and Cold Water Distribution System.
MS 1757 : Part 1 : 2008
Chlorinated Poly (Vinyl Chloride) (PVC-C) – Plastic Piping System – Part 2 : Specification for Schedule
40 Socket-type Pipe Fittings.
MS 1757 : Part 1 : 2008
Chlorinated Poly (Vinyl Chloride) (PVC-C) – Plastic Piping System – Part 3 : Specification for Schedule
80 Pipe Fittings.
Updated 01-02-2013
vi
Items Standard Number Standard Title
MS 2045 : 2007
Chlorinated Poly (Vinyl Chloride) (PVC-C) Plastic Hot-and-Cold-Water Distribution Systems –
Specification.
Acrylonitrile-Butadiene-
Styrene (ABS) Fittings
MS 1419: Part 1: 2007
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for Pressure Applications – Part 1: Specification for Compounds, Pipes and Fittings
(First Revision)
AS/NZS 3518: 2004 Acrylonitrile Butadiene Styrene (ABS) Compounds, Pipes and
Fittings for Pressure Application
Glass Reinforced Plastic (GRP)
Fittings ISO 10639: 2004
Plastics Piping System for Pressure and Non-pressure Water Supply – Glass Reinforced Thermosetting
Plastics (GRP) Systems Based On Unsaturated Polyester (UP) Resin
Steel Pipe Specials
BS 534: 1990 Steel Pipes, Joints and Specials for Water and Sewage
MS 1968 : 2007
Non-alloy steel tubes and fittings for the conveyance of aqueous liquids
including water for human consumption – technical delivery
conditions Stainless Steel (SS) Threaded
Fittings ISO 4144: 2003
Pipework – Stainless Steel Fittings Threaded in Accordance with ISO 7-
1.
Stainless Steel (SS) Welded
Fittings
MS 1842: 2010
Wrought Austenitic Stainless Steel Piping Fittings – Specification (First
Revision).
ASTM A403/A403M-10a
Standard Specification for Wrought Austenitic Stainless Steel Piping
Fittings Stainless Steel
(SS) Press Fittings
SAS 322: 2003 Stainless Steel Press Fittings
Ductile Iron Fittings
MS 1919: 2006
Ductile Iron Pipes, Fittings, Accessories and Their Joints for
Water Pipelines – Requirement and Test Method
BS EN 545 : 2010
Ductile Iron Pipes, Fittings, Accessories and Their Joints for
Water Pipelines – Requirement and Test Method
Copper Fittings BS EN 1254-1: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings with
Short Ends for Capillary Brazing to Copper Tubes.
Updated 01-02-2013
vii
Items Standard Number Standard Title
BS EN 1254-2: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings with Compression Ends for Use with
Copper Tubes.
BS EN 1254-4: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings
Combining Other End Connections with Capillary or Compression Ends.
Steel Fittings with Plastic Lining CJ/T 136: 2001 Malleable Iron Threaded Fittings of
Lining Plastic for Water Supply.
Variable Adapter Spesifikasi JKR 20200-0045-99
JKR Standard Specification for Detachable Joints and Variable
Adaptors for uPVC, Ductile Iron and AC Pipes.
Flange Adapter Spesifikasi JKR 20200-0048-99
JKR Standard Specification For Flexible Couplings and Flange
Adaptors.
Flexible Coupling Spesifikasi JKR 20200-0048-99
JKR Standard Specification For Flexible Couplings and Flange
Adaptors.
Detachable Joint Spesifikasi JKR 20200-0045-99
JKR Standard Specification for Detachable Joints and Variable
Adaptors for uPVC, Ductile Iron and AC Pipes.
Ferrous Saddle Spesifikasi JKR 20200-0044-99
JKR Standard Specification for Ferrous Saddles.
Pillar Hydrant
Spesifikasi JKR 20200-0042-99
JKR Standard Specification for Ductile Iron Pillar Hydrants.
MS 1395: 1996 Specification for Pillar Hydrants
Ductile Iron (DI) Strainer
Spesifikasi JKR 20200-0100-01
JKR Standard Specification for Ductile Iron Strainer (DN 50 to DN
600)
Updated 01-02-2013
viii
Items Standard Number Standard Title
Swivel Ferrules Spesifikasi JKR 20200-0174-04
JKR Standard Specification for Ferrules
Under Pressure Vertical Ferrules MS 1396: 2006 Ferrules – Specification (First
Revision)
Manhole Cover BS EN 124 : 1994
Gully Tops and Manhole Tops for Vehicular and Pedestrian Areas.
Design Requirements, Type Testing, Marking, Quality Control.
(c) Tank
Glass Coated / Glass Lined / Glass Fused /
Epoxy Coated / Epoxy Lining
AWWA D103-97, ANSI/AWWA D103-09
Factory-Coated Bolted Steel Tanks For Water Storage
PE / HDPE Tanks Storage
Tank
MS 1225 : Pt 1 : 2007 Polyethylene (PE) Tanks For Cold Water Storage; Part 1: Capacity up
to 600G (Second Revision)
MS 1225 : Pt 2: 2006 Polyethylene (PE) Tanks For Cold Water Storage; Part 2: Capacity more than 600G (First Revision)
GRP/FRP Sectional Water
Tank MS 1390 : 2010
Specification for glass reinforced polyester panels & panel water
tanks
FRP One-Piece Water Tank
BS EN 13280 : 2001
Specification for glass fibre reinforced cistern of one-piece and sectional construction for storage
above ground of cold water
MS 1241 : 1991 Specification for Fibreglass Water Tanks – Effective Capacity of Less
Than 2000L
BS 7491: Pt 2 : 1992
Glass Fibre Reinforced Plastic Cisterns for Cold Water Storage.
Specification for one piece cisterns of nominal capacity for 500L to
25000L.
Updated 01-02-2013
ix
Items Standard Number Standard Title
Pressed Steel Sectional
Rectangular Tank Panel
BS 1564 : 1975 Specification for Pressed Steel Sectional Rectangular Tanks
Stainless Steel Storage Tank JKR 20200-0041-99 Stainless Steel Water Tanks (With
Effective Capacity Up to 15,000L)
Stainless Steel Storage Tank (Rectangular / Panel Tank)
CNS 9443 : 1989 Stainless Steel Storage Tanks
(d) Valves
Butterfly Valve BS EN 593 : 2004 Industrial Valves. Metallic Butterfly Valves
Air Valve
JKR 20200-0097-01 Ductile Iron Air Valves (Revised Edition 2001)
JKR 20200-0043-99 Ductile Iron Air Valves (Revised Edition 1999)
ANSI / AWWA C512-2004
Air Release, Air Vacuum, and Combination Air Valve for
Waterworks Service.
BS EN 1074-4 : 2000
Valves for Water Supply. Fitness for Purpose Requirements and
Appropriate Verification Tests. Air Valves.
Gate Valve
MS 1049 : 1986 Specification for Double Flanged Cast Iron Wedge Gate (sluice)
valves for waterworks purposes.
BS EN 12288 : 2010 Industrial Valves. Copper Alloy Gate Valves
BS EN 1171 : 2002 Industrial Valves. Cast Iron Gate Valves
JKR 20200-0077-00 Ductile Iron Type B Large Sluice Valves (DN700-DN1800)
BS 5163-1 : 2004 Valves for Waterworks Purposes. Predominantly key-operated cast iron gate valves. Code of practice
Updated 01-02-2013
x
Items Standard Number Standard Title
BS 5163-2 : 2004
Valves for Waterworks Purposes. Stem Caps for use on isolating
valves and associated water control apparatus. Specification.
Check Valve
BS EN 12334 : 2001 Industrial Valves. Cast Iron Check Valves.
BS EN 14341 : 2006 Industrial Valves. Steel Check Valves
BS 1953 : 1964 Copper Alloy Check Valve for general purposes.
BS EN 12288 : 2003 Specification for copper alloy globe, globe stop, check and gate valves
Control Valve BS EN 1074-5:2001
Valves for Water Supply – Fitness for Purpose Requirements and
Appropriate Verification Tests. Part 5 : Control Valve
Stopvalve
MS 1022 : 2005 Stopvalves – Specification (First Revision)
BS 6675 : 1985 Specification for servicing valves (copper alloy) for water services.
BS EN 1213 : 2000 Building Valves. Copper alloy
stopvalves for potable water supply in buildings. Test & Requirements.
JKR 20200-0055-99 Specification of Mechanical Stopvalve for water supply usage
Ball Valves
BS 1212 : Part 1 : 1953 Piston Type Ball Valves (Excluding Floats)
BS 1212 : Part 2 : 1971 Diaphragm Type (Brass Body) ball Valves (Excluding Floats)
Landing Valve
BS 5041 : Pt 1 : 1987 Fire Hydrant Systems Equipment. Specification for landing valves for
wet risers
BS 5041 : Pt 3 : 1975 Fire Hydrant System Equipment.
Specification for landing valves for dry risers.
Updated 01-02-2013
xi
Items Standard Number Standard Title
Mixing Valve (Manually Operated)
BS EN 1286 : 1999
Mixing Valves (Manually Operated) for ablutionary and domestic
purposes. Non Thermostatic, non-
compensating mixing valves
Float Operated Valve
MS 1882 : 2005 Piston Type Float Operated Valves – Specification
JKR 20200-0059-99 Specification of Brass Float Valves
Pressure Reducing Valves BS EN 1567 : 2000
Building Valves. Water Pressure Valves and Combination Water
Reducing Valves. Requirements and Test.
Penstock
BS 7775 : 2005 Penstocks for use in Water and Other Liquid Flow Applications.
Specification.
JKR 20200-0108-01 JKR Standard Specification for Penstocks (Revised Edition 2001)
(e) Back flow preventer
Dual Check
Backflow Preventer
BS EN 14454 : 2005
Devices to prevent pollution by backflow of potable water. Hose
Union backflow preventer DN15 to DN32 inclusive. Family H, Type A.
AS/NZS 3500.1:2003 Plumbing and drainage - Water Services
Reduced Pressure Zone
Assembly
BS EN 12729 : 2002
Devices to prevent pollution by backflow of potable water.
Controllable backflow preventer with reduced pressure zone. Family B,
Type A
AS/NZS 3500.1:2003 Plumbing and drainage - Water Services
(f) Meter
Electromagnetic / Ultrasonic Flowmeter
OIML R 49-1
Water Meters Intended for the metering of Cold Potable Water and
Hot Water Part 1 : Metrological and technical
requirement
Water Meter OIML R 49-1
Water Meters Intended for the metering of Cold Potable Water and
Hot Water Part 1 : Metrological and technical
requirement
Updated 01-02-2013
xii
Items Standard Number Standard Title
ISO 4064-1 : 2005
Measurement of Water Flow in fully charged closed conduits – Meters for Clod Potable Water and Hot Water –
Part 1 – Specification
(g) Taps & Mixer
Bib Tap / Pillar Tap/ Faucet
BS EN 200 : 2008
Sanitary Tapware. Single Taps and combination Taps For Water Supply
Systems of Type 1 and Type 2. General Technical Specification.
AS / NZS 3718 : 2005 Water Supply – Tap ware
MS 1461 : 1999 Specification for draw off taps with metal bodies for water service
Mixer
BS EN 817 : 2008 Sanitary tapware. Mechanical
mixing valves (PN 10). General technical specifications.
BS EN 1286 : 1999 Mixing Valves (manually operated)
for ablutionary and domestic purposes.
(h) Water Closet
Water Closet Pan
MS 1522 : 2007 Vitreous China Water Closet Pans – Specification (Second Revision)
MS 147 : 2001 Specification for quality of Vitreous China Sanitary Appliances (First
Revision)
Moulded One-piece Water
Closet
MS 1522 : 2007 Vitreous China Water Closet Pans – Specification (Second Revision)
MS 795 : 2002 Specification For WC Flushing Cisterns & Flush Pipe
MS 147 : 2001 Specification for quality of Vitreous China Sanitary Appliances (First
Revision)
(i) Water Closet and Flushing Cistern
Water Closet Flushing Cistern & Flush Pipes
MS 795 : 2002 Specification For WC Flushing Cisterns & Flush Pipe
Updated 01-02-2013
xiii
Items Standard Number Standard Title
(j) Flush valve
Flush Valve JKR 20200-0130-01 JKR Standard Specification For Flush Valve
(k) Sanitary Appliances
Urinal bowls, Pedestal, Bidets,
WC Pans
MS 147 : 2001 Specification for quality of Vitreous China Sanitary Appliances (First
Revision) Cistern & Cover
Wash Basin
(l) Urinals
Urinals MS 1799 : 2008 Urinals - Specification
(m) Water Treatment Chemical – Coagulant & Flocculant.
Product Based on Aluminium
MS 699:2008 Aluminium Sulphate for Use in
Potable Water Supply –Specification (Second Revision)
MS 1454:2007 Liquid polyaluminium chloride for
use in potable water supply – specification (first revision), 2007
MS 1572:2003 Specification for Sodium Aluminate used for potable water supply
Product Based on Iron
MS 1450:1999 Specification for liquid ferric chloride for potable water treatment
MS 1452:1999 Specification for liquid ferric sulphate for potable water treatment
MS 1456:1999 Guidelines for the application of
liquid ferric based salts in potable water treatment
Product Based on PolyDADMAC MS 1930:2007
Poly(polydiallyldimethyl ammonium chloride) or polyDADMAC for use in
potable water supply
Updated 01-02-2013
xiv
Items Standard Number Standard Title
Product based on Polyacrylamide MS 1928:2007 Polyacrylamides for use in potable
water supply (specification)
Product based on Polyamine MS 1929: 2007 Polyamines for use in potable water
supply (specification)
(n) Water Treatment Chemical – Softening Agent and PH Adjustment.
Hydrated Lime / Calcium
Carbonate MS 1836:2005 Hydrated Lime and slurry lime for
use in potable water supply
Sodium Carbonate / Soda
Ash MS 1551 : 2002
Specification for soda ash (sodium carbonate) used for potable water
supply
(o) Water Treatment Chemical – Chemicals for Disinfection.
Chlorine MS 171:2003 Specification for liquid chlorine used for potable water supply
Sodium Hypochlorite MS 1718:2003 Sodium Hypochlorite for use in
potable water supply
Calcium Hypochlorite MS 1548:2003
Specification for calcium hypochlorite use for potable water
supply 2003
Potassium Permanganate MS 1576: 2003
Specification for potassium permanganate used for potable
water supply
Copper Sulphate MS 1571:2003 Specification for Copper Sulphate used for potable water.
(p) Water Treatment Chemical – Chemicals for Flouridation.
Sodium Flouride MS 1573 : 2003 Specification for sodium fluoride used for potable water supply
Sodium Silicoflouride MS 1724:2004
Sodium silicofloride for use in potable water supply specification
2004
(q) Water Treatment Chemical – Filter Media & Other Chemicals.
Sand MS 847: 1983 Specification for silica sand for the manufacturer of sodium silicate.
Updated 01-02-2013
xv
Items Standard Number Standard Title
Sodium Hydroxide /
Caustic Soda MS 700: 1981 (Specification) for sodium hydroxide
(technical grades)
Activated Carbon
MS 873:2005 Powdered activated carbon for use
in potable water supply – specification
MS 1815 : 2005 Granular activated carbon for use in potable water supply (specification)
(2) Sewerage products under Category A and the approved respective standards
Items Standard Number Standard Title
Package
plant
TS SPAN 1401:2010 Technical Specifications for Sewage
Treatment System, Part 1: Prefabricated Tanks - Packaged Plants.
Septic tank
MS 2441-1:2012
Onsite sewage treatment units Part 1:
Prefabricated septic tanks specifications (Note: Standards had been approved, pending publication by end Feb 2012)
Manholes
MS 881: Pt 1 Specification for precast concrete pipes and fittings for drainage and sewerage
Manhole
cover
BS EN 124 Gully tops & manhole tops for vehicular &
pedestrian areas design req., type testing, marking, quality control
Vitrified clay
pipe
a) MS 1061 b) BS EN 295-1
Jacking pipe c) BS EN 295-7
Vitrified clay pipes and fittings and pipes
joints for drains and sewers : Part 1 : Requirement (First Revision)
Vitrified clay pipes and fittings and pipe
joints for drains and sewers.
Jacking pipe
Vitrified clay pipes and fittings and pipe joints for drains and sewers.
Requirements for vitrified clay pipes and joints for pipe jacking
Updated 01-02-2013
xvi
Items Standard Number Standard Title
Reinforced
concrete pipe
MS 881: Pt 1
Specification for precast concrete pipes and fittings for drainage and sewerage Part:2 Specification for Inspection Chambers and gullies
AS 4058
Precast concrete pipes (pressure and non-pressure)
BS 5911-1
Jacking pipe
Concrete pipes and ancillary concrete products
HDPE pipe
Profile Wall
DIN 16961
Profile Wall
Thermoplastics pipes and fittings with profiled wall and smooth pipe inside
Solid Wall
MS 1058
Solid Wall
Polyethylene (PE) piping systems for water supply
Ductile iron pipe
BS EN 598
Ductile iron pipes, fittings, accessories
and their joints for sewerage applications. Requirements and test methods
Glass-fibre reinforced
pipe
BS 5480
Specification for GRP pipes, joints and fittings for use for water supply or sewerage
ASTM D 3262
Specification for GRP Sewer Pipe
PVC pipe (PVC-U,
PVC-M, PVC-
AS/NZS 1477
PVC pipes and fittings for pressure applications
Updated 01-02-2013
xvii
Items Standard Number Standard Title
C)
BS 4660
Specification for unplasticized polyvinyl chloride (PVC-U) pipes and plastics fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage
BS 5481
Specification for unplasticized PVC pipe and fittings for gravity sewers
JIS K 6741
uPVC Pipes for General Fluids
(Excluding Potable Water )
MS 979
Specification for unplasticizies sewerage pipe and fitting Part 1: pipes of diameter
100mm and 155mm
MS 979
Part 2 Pipes of diameter 200mm and
above
AS/NZS 1477
PVC pipes and fittings for pressure
application
BS EN 1401-1
Unplasticized Polyvinyl Chloride (PVC-U) Fittings For Non-Pressure Underground
Drainage and Sewerage
ABS pipe
MS 1419: Part 1
Specification for acrylonitrile butadiene styrene (ABS) pipes and fittings for pressure application Part 3 Solvent
cement & priming (cleaning) fluids for use with ABS pipes & fittings
Steel Pipes BS 534 Steel Pipes, Joints and Specials for Water and Sewage
Stainless Steel Pipes ASTM A312
Standard Specification for Seamless, Welded, and Heavily Cold Worked
Austenitic Stainless Steel Pipes
Updated 01-02-2013
xviii
Items Standard Number Standard Title
Stainless Steel Fittings ASTM A403 Standard Specification for Wrought
Austenitic Stainless Steel Piping Fittings
Penstock
(Wall mounted,
channel type, weir gate)
BS7775
Penstocks for use in water and other liquid flow applications. Specification
Cast Iron Pipes & Fittings
ISO 6594 Cast Iron Pipes & Fittings - Spigot Series
Gate valve
MS 1049
Specification for double flanged cast iron wedge gate (sluice) valves for
waterworks purposes
BS 5163
Valves for waterworks purposes. Stem
caps for use on isolating valves and associated water control apparatus.
Specification
EN 1074 (Part 2)
Valves for water supply - Fitness for
purpose requirements and appropriate verification tests - Part 2:
Isolating valves
BS EN 1171
Industrial valves. Cast iron gate valves
Check valve
BS EN 12334
Industrial valves. Cast iron check valves
Butterfly valve
BS EN 593
Industrial valves. Metallic butterfly valves
Air/air release
valve
JKR20200-0097-01
JKR specification for air valves
(as of July 2012)
Updated 01-02-2013
i
APPENDIX II
(1) Water supply products under Category B and the respective standards/requirements
Product Testing Standards / Requirements
(a) Lining / coating / waterproofing / sealant / adhesive
Lining / coating / waterproofing /
sealant / adhersive
MS 1583 : Part 1 : 2003
Suitability of Non-Metallic Products
for Use in Contact with Water Intended for Human Consumption with Regard to Their Effect on the
Quality of the Water : Part 1 : Specification
BS 6920 – 1 : 1996
Suitability of Non-Metallic Products for Use in Contact with Water
Intended for Human Consumption with Regard to Their Effect on the Quality of the Water : Specification
AS/NZS 4020: 2005 Testing of Products for Use in Contact with Drinking Water
(b) Tank
Cylindrical Double Fold System BS 5950-1:2000
Structural Use of Steelwork in Building Part 1 : Code of Practice for
Design – Rolled and Welded Section.
Corrugated Steel Panel With
Polyethylene-Lined Water Storage Tank
BS 1449:Pt 1: 1991 Steel Plate, Sheet & Strip. Carbon and carbon-manganese sheet and
strip. SS 245:1995 (Cl.
10.2.1 & Cl 10.2.2)
Specification for Glass Reinforced Polyester Sectional Water Tank
(c) Pump
Pump ISO 9906 : Rotodynamic pumps – Hydraulic Performance Acceptance Tests –
Grades 1 and 2.
(d) Chemical for Water Treatment
Chlorine Dioxide (for disinfection &
NSF/ANSI 60-2011
Drinking Water Treatment Chemical – Health Effects
Updated 01-02-2013
ii
oxidation)
BS EN 12671:2009 –
Chemical Used for Treatment of
Water Intended for Human Consumption – Chlorine Dioxide
Generated in Situ
All kind of imported
polymer for flocculant
NSF/ANSI 60-2011
Drinking Water Treatment Chemical
– Health Effects
(e) Small Water Treatment System
Small Water Treatment System/
Compact Water treatment System
Require for a pilot project to show that the system work as claimed and treated water produced comply with the National Standard for Drinking Water.
(f) New Innovative Product for Water Treatment
Any product which is not listed in category
A or B for water supply application
Require for a pilot project to show that the product/system work as claimed.
(as of July 2012)
Updated 01-02-2013
i
(2) Sewerage products under Category B and the respective standards/requirements
Product
Testing Standards / Requirements
Small Sewage Treatment System
CAN/CSA B66-05 Design, material and manufacturing requirements for prefabricated septic tanks and sewage holding tanks. (Note: Standards is only for prefabricated tanks components. Conformity assessment for treatment efficiency is subject to either pilot project for new application or sampling & testing by 3rd party for existing installation)
Screw conveyor
a) BS 4409-1 Screw conveyors. Specification for
fixed trough type.
Pump (Centrifugal- submersible, end suction, self priming)
a) BS EN ISO 5198 Centrifugal, mixed flow and
axial pumps. Code for hydraulic performance tests. Precision class.
b) BS EN ISO 5199 Technical specifications for centrifugal pumps. Class II.
c) BS EN ISO 9905 Technical specifications for centrifugal pumps. Class I.
d) BS EN ISO 9908 Technical specifications for centrifugal pumps. Class III.
e) ISO 9906 Rotodynamic pumps. Hydraulic performance acceptance tests - Grades 1 and 2.
f) JIS B 8325 Submersible Motor Pumps for Sump.
Pump (Positive displacement - screw, lobe)
) BS EN 14343 Rotary positive displacement pumps.
Performance tests for acceptance.
Surface aerator, brush aerator, paddle wheel aerator, hydrojet aerator, ejector, aspirating aerator, submersible aerator, diffuser
a) BS EN 12255-15 Wastewater treatment plants.
Measurement of the oxygen transfer in clean water in aeration tanks of activated sludge plants
b) ASCE/EWRI 2-06 Measurement of oxygen transfer in clean water
Updated 01-02-2013
ii
Product
Testing Standards / Requirements
(Note: Standards for material is subject to manufacturer recommendations)
Mixer, agitator
a) BS ISO 21630 Pumps. Testing. Submersible
mixers for wastewater and similar applications.
Air blower
For blowing application a) JIS B 8341 Testing methods for displacement
compressors. For vacuum application a) BS ISO 21360 Vacuum technology. Standard
methods for measuring vacuum-pump performance. General description.
Vacuum sewerage system
a) BS EN 1091 Vacuum sewerage systems outside
buildings b) WSA 06 Vacuum sewerage code of Australia Vacuum pump a) BS ISO 21360 Vacuum technology. Standard
methods for measuring vacuum-pump performance. General description.
Sewer liner
CIPP a) BS EN 13566 Part 1 – 4 Plastics piping systems
for renovation of underground non-pressure drainage and sewerage networks
b) ASTM F2019-03, Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in- Place Thermosetting Resin Pipe (CIPP)
c) ASTM D5813 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
FRP slip lining & HDPE lining a) BS EN 13566 Part 1 – 4 Plastics piping systems
for renovation of underground non-pressure drainage and sewerage networks
Updated 01-02-2013
iii
Product
Testing Standards / Requirements
b) BS EN ISO 178 Plastics. Determination of
flexural properti
Grit & Grease Removal – Grit & grease collector/ Grit collector/ Grease collector
Require for a pilot project to show that the
product/system work as claimed.
Clarifier/ Sedimentation - Sludge scrapper & scum skimmer/ Sludge scrapper/ Scum skimmer
Require for a pilot project to show that the
product/system work as claimed.
Gravity thickener
Require for a pilot project to show that the
product/system work as claimed. Odour Control & Treatment
Require for a pilot project to show that the
product/system work as claimed.