INSTRUCTIONS

Sparta Series865BLED

2

Thank you for choosing Angler.

The 865BLED from Angler’s Sparta Series is a slim, lightweight, and powerful LED fixture that will add versatility to your set. This fixture is ideal for head shots, portraits, and interviews on small sets due to its color accuracy and precise brightness and color temperature control. It operates on plug-in power, but when you need to take it to a location shoot, it also operates on two NP-F batteries.

Exact color temperature control lets you match other light fixtures or natural daylight. Brightness is adjusted in 1% increments, so you can dial in the exact brightness for your exposure. Included barndoors limit direction of your beam by controlling light spill. With an additional wireless remote (sold separately), you can control the output and color temperature of multiple 865BLED lights as well as several lights from Genaray.

Precautions Please read and follow these instructions, and keep this manual in a safe place.

Keep this unit away from water and any flammable gases or liquids.

Do not leave the device in a closed vehicle under the sun or in other areas subject to very high temperatures.

3

Do not attempt to disassemble or repair the equipment. There are high-voltage components inside the unit. Failure to observe this precaution could result in electric shock or product malfunction. This will void the warranty, and Angler will not be responsible for any damage.

Use only the correct, recommended voltage.

Make sure the unit is powered off when plugging it into a power source.

Disconnect the power cord when not in use.

Do not stare directly at the lights when they are powered on.

Use only parts provided by the manufacturer.

Handle this product with care.

Clean this product with a soft, dry cloth.

Keep this unit away from children.

Make sure the item is intact and that there are no missing parts.

All photos are for illustrative purposes only.

4

OverviewBarndoors

Two-way 5/8 inch receiver

LEDarray

Locking tab

Yoke

Locking knob

Diffuser

Accessory slots

5

Also included:

AC power cord AC power adapter and cord Travel Case

Tilt locks

Power input

LEDdisplay

Battery plates

Channel select button Power button

Check battery button

Adjustment knob

Tab release buttons

6

Mounting the 865BLED

1. Make sure the tilt locks are securely tightened before mounting the fixture.

2. Loosen the locking knob, and mount the receiver vertically or horizontally onto a light stand with a 5/8 in. baby pin.

3. Tighten the locking knob until secure.

4. Once the light is securely mounted, loosen the tilt locks to adjust to position of the light.

Powering On the Light AC Power When operating on AC power, remove the batteries.

1. Plug the power adapter into the light, and plug the power cord into an available outlet.

2. Press and hold the power button until the light comes on.

2

7

Battery Power

When operating on battery power, unplug the power adapter from the AC outlet and from the light.

1. Place two NP-F batteries into the battery plates, and slide them toward the contacts until the battery is firmly in place.

2. Press and hold the power button until the light comes on.

Press the battery check button to see the remaining charge in your batteries. Pro tip: For uninterrupted operation, pack a few extra batteries in your gear bag.

Adjusting the Color Temperature

1. Press the adjustment dial so the LED appears under Color.

2. Use the adjustment knob to set the color temperature from 3200 K (tungsten balance) to 5600 K (daylight balance).

1

1

8

Adjusting the Brightness

1. Press the adjustment dial so the LED appears under Dimmer.

2. Select the output level from 10 to 99.

Wireless Operation The brightness and color temperature settings can be controlled remotely from up to 100 feet away with the Genaray MB-WRT Wireless Remote (sold separately).

1. To set a channel on the 865BLED, press the channel button, and select the channel with the adjustment knob.

2. Press the channel button again to confirm the selection.

Important! Make sure the remote is set to the same channel as the 865BLED. For more information about wireless operation, refer to the MB-WRT user manual.

2

9

Diffuser and Barndoors

Removing the Barndoors and Diffuser

1. Move either one of the tab release buttons and lower the locking tab.

2. Slide the barndoors and/or the diffuser off the accessory rails.

To replace the Barndoors and Diffuser

1. Raise one of the locking tabs to its locked position. Make sure the other locking tab is lowered to the unlocked position.

2. Slide the diffuser into the inner accessory slot, and slide the barndoors into the outer accessory slot.

3. Pull the locking tab up until it locks into place.

1

2

10

LIGHT FIXTURE

LED Chip Type SMD LED

Output Power 36 W

Beam Angle 60°

Color Temperature 3200 to 5600 K

Color Accuracy Standard

CRI 94.6TLCI 96.5

Cooling System None

Dimming Yes, 10% - 100% in 1% increments

Display LED

Housing Material Metal

Photometrics3200 K: 2609 lx @ 3 ft.4400 K: 2854 lx @ 3 ft.5600 K: 2766 lx @ 3 ft.

Number of LEDs 160

Expected Lamp Life 50,000 HR.

Dimensions (W×H×D)Light: 8 × 6.9 × 1.5 in. (20.3 × 17.5 × 3.8 cm)With Yoke: 12 × 10.75 × 2 in. (30.5 × 27.3 × 5.1 cm)

WeightLight (with yoke and barndoors): 3.2 lb. (1.45 kg)

Specifications

CONNECTORS

Battery Plate NP-F (×2)

Power INPUT CONNECTOR

bARREL

11

YOKE

Yoke Material Metal

Yoke Type Yoke/Bracket

Tilt 360°

Remote Operation

Remote Control Type

2.4 GHz

Number of Channels 99

Wireless Range 100 ft. (30 m)

POWER

AC Input Power 100 to 240 V AC, 50/60 Hz

DC Input Power 13 to 19 V DC

Power Adapter 15 V, 2.4 A DC

Power Source AC adapter, NP-F battery (×2)

Max Power Consumption

36 W

MOUNTING

Fixture Mount Two-way 5/8 in. receiver

One-Year Limited WarrantyThis Angler product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state.To obtain warranty coverage, contact the Angler Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Angler along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense.

For more information or to arrange service, visit www.anglerlights.com or call Customer Service at 212-594-2353.

Product warranty provided by the Gradus Group.www.gradusgroup.com

Angler is a registered trademark of the Gradus Group. © 2019 Gradus Group LLC. All Rights Reserved.

ANGLERA Gradus Group Brand

GG1