special lubricants for textile machinery

Lubrication is our World

Special Lubricantsfor Textile Machinery

2

Note: The overview of our partner companies from the textile machine sector shown on pages 4and 5 is not exhaustive.

For the next edition of this brochure, we will be pleased to include in this list the logo of othertextile machine and component manufacturers cooperating with us in the generation of lubri-cant recommendations for textile machine operators.

Contents Page

1.0 Introduction 3

Lubricants for:2.0 Preparatory and spinning machines (staple fibres) 6-73.0 Spinning machines (staple fibres) 8-94.0 Synthetic fibre spinning machines (filaments) 10-115.0 Synthetic fibre processing machines (filaments) 12-136.0 Twisting and spool winding machines 14-157.0 Apparatuses, accessories and special machines 16-178.0 Knitting machines 18-199.0 Warp knitting machines 20-21

10.0 Sizing machines and looms 22-2311.0 Textile finishing machines 24-2912.0 Gear units and electric motors in textile machines 30-3113.0 Lubricants for compressors in the textile industry 32-33

14.0 Product survey14.1 Lubricating oils 34-3514.2 Release agents 3614.3 Lubricating greases 36-3814.4 Lubricating pastes 3914.5 Solid lubricants 39

ALTEMPALTEMPANBARRIERTAFORMINOLGRAFLOSCONHOTEMPISOFLEXKlüber MadolKlüberoil TEXKlüberpasteKlüberplex

Klüber SilvertexKlüberspeedKlüberquietKlüber SummitKlübersynthKlübertempLAMORAMICROLUBEMOLYBKOMBINPARALIQPETAMO

PRIMIUM FLUID SPECIALQUIETSCH-EXSTABURAGSSTRUCTOVISSYNTHESOTEX SYNTHESOUNIMOLYUNISILKONWOLFRACOAT

are registered trademarks of Klüber Lubrication München KG

3

1.0

The operation of modern-day, high-performance textile

machinery involves a multitude of lubrication requirements

which standard lubricants can meet only partly, if at all.

The German Standard DIN 64 921, “Lubricants for textile

dyeing and finishing machinery”, provides a general listing

of only two lubricating greases based on mineral oils, plus

some lubricant groups (e.g. lubricating and hydraulic oils)

and adhesive lubricants on a mineral oil basis, together

with the corresponding standard code letters. This does

not yet amount to overall application engineering guidelines

and standardization options.

Formulating these is rendered more difficult by the

extremely wide variety of different friction points, with their

very different stresses and environmental conditions. It is

here that special lubricants come into their own.

At Klüber Lubrication, application-tailored solutions involv-

ing special lubricants for highly stressed friction points in

textile machinery have a long tradition. All over the world,

machine manufacturers and users can benefit from high-

quality lubricants of proven efficiency. Special lubricants,

when properly selected and utilized, not only improve oper-

ational reliability, they also cut maintenance costs sub-

stantially. The very high sums which still have to be spent

on correcting damage caused by friction and wear can be

effectively reduced by the use of special lubricants. In this

context it is of course of crucial importance to choose the

right lubricant – this is the key to successful lubrication. The

choice of a lubricant must be governed by the technical

and operational requirements profile of the friction point

involved and not primarily by the costs. The performance

and functional reliability of the lubricant are much more

important than a price per pound comparison showing the

supposed advantages of “cheap lubricant purchasing”.

High-quality special lubricants, though they may cost more,

are more economical for you in the long run.

Lubrication and lubricants are today more than ever the

subject of meticulous scrutiny by engineers and materials

planning staff. But special lubricants also make an impor-

tant contribution to reducing environmental pollution; often

only small quantities are needed to provide long-term or

lifetime lubrication in cases where total-loss lubrication

would not only be uneconomical but would also involve

substantial environmental difficulties.

In this brochure we present “intelligent” solutions for the

highly stressed friction points found in textile machinery,

restricting ourselves, of course, to the most important and

widespread cases of typical applications.

Technical development, however, is never at a standstill;

and we will always welcome your suggestions for expand-

ing and supplementing this brochure.

On the following pages, you will find details of typical appli-

cations and solutions to lubrication problems involving the

following types of textile machinery:

• Spinning machines

• Synthetic fibre spinning machines

• Synthetic fibre processing machines

• Twisting and spool machines

• Apparatuses and special machines

• Knitting machines

• Sizing machines and looms

• Textile finishing machines

All Klüber products recommended are high-performance

lubricants, most of them on a synthetic basis.

They offer:

• maximum operational reliability

• low machinery servicing costs

• long maintenance intervals

• environment-friendly utilization

For detailed descriptions of the products, with additional

information on the applications involved, please consult the

appropriate product information leaflets, which you can

obtain from us free of charge.

Please note that due to the extraordinarily large number

of technical solutions possible, the illustrations in this

brochure do not in each and every case relate directly to

the lubricant recommendations accompanying them. They

are intended merely as examples; the operating and main-

tenance instructions of the machine manufacturer as well

as the lubricant recommendations are of course binding.

Our network of production and sales companies all over

the world ensures that you always have a supplier of our

products conveniently near to you, who will also keep you

up-to-date with the latest results from research, develop-

ment and testing.

Introduction

4

GTM

Tessili Impianti

Klüber Lubrication – Partner of Textile Industry

6

2.0

Example Machine / Component Lubrication Problem / Requirements

Rotary plate (plain bearings) in carders anddrawing frames

Top and bottom drawingroller bearings in drawframes

Rolling bearings in thedrawing assembly(ring spinning frame)

Top roller bearings(ring spinning frame)

Frequent maintenance

High bearing temperature, danger of contamination of

the spinning material (sliver) in the can

Insufficient bearing life if lubricated with standard

greases

Overheating of bearings

“Bearing bleeding”

Excessive separation of the oil from the grease in the

bearings, necessitating frequent relubrication

Lubricants for Preparatory and Spinning Machines

7

Staple fibres

Klüberpaste 46 MR 401

Modern white multi-purpose

lubricating paste

or

ALTEMP Q NB 50

Well-proven, light-coloured lubri-

cating and assembly paste

ISOFLEX TOPAS NB 52

Fully synthetic special grease for

high-speed needle bearings

or

STABURAGS NBU 12 / 300 KP


Special high-pressure grease with

excellent long-term effectiveness

Long-term lubrication lasting for

weeks; minimized contamination and

low-wear operation

Klüberpaste 46 MR 401 or

ALTEMP Q NB 50 should be in every

workshop since, being an assembly

paste, they protect against fretting

corrosion.

Relubrication intervals may exceed the

recommended intervals by far.

ISOFLEX TOPAS NB 52

is recommended by Messrs. Vouk for

older machine types.

Rieter / Ingolstadt uses

ISOFLEX LDS 18 SPECIAL A for initial

lubrication and lists it in the lubricant

recommendations.

Excellent corrosion protection and

long-term lubrication of bottom roller

bearings (needle bearings)

On top rollers (deep groove ball bear-

ings) a service life of several years

without relubrication is achievable.

STABURAGS NBU 12 / 300 KP has

been used for initial lubrication for

example by Spindelfabrik SUESSEN

for many years.

Recommended Lubricants Advantages Notes

8

INA

3.0


Needle bearings in bottom drawing rollers(ring spinning frame)

OE spinning turbines(direct or TwinDisc drive)

Opening rollers(OE spinning frame)

Extensive maintenance in case of bearing failure, thus

long-term lubrication required

Extremely high speeds

Overheating and wear of the bearing

Too frequent relubrication

Bearing wear may lead to uneven opening

of the sliver.

Lubricants for Spinning Machines

9

Staple fibres


Special high-pressure grease with

excellent long-term effectiveness

Klüber high-speed lubricants for

open-ended spinning turbines,

opening and pressure rollers

ISOFLEX NBU 15

ISOFLEX NCA 15

ISOFLEX LDS 18 SPECIAL A

Depot and relubricating oil for

Rieter OE machines

ISOFLEX PDP 65

ISOFLEX NBU 15

Besides long-term lubricity, very good

corrosion protection

Low maintenance requirements

Long-term lubrication

Increased operational reliability and

extended bearing life with very long

relubrication intervals

The Klüber high-speed lubricants

listed are recommended by leading

rotor manufacturers.

The range of lubricants is continuously

adjusted to keep up with development

trends in the rotor manufacturing

sector.

Higher operational reliability ensures

flawless opening of the sliver.


10

4.0


Spinning pumps

Spinerets

Godet bearings

Pre-heating temperature 260 °C to 280 °C

Start-up problems due to deficient oil film

or oil residues

Difficulty in dismantling spinerets after long produc-

tion runs, caused by seized screw threads

Clogging of the fine nozzles in the spineret plate

results in malfunctions and delays in production.

“Bleeding” of the grease results in impeded bearing

operation.

Relubrication intervals too short

Lubricants for Synthetic FibreSpinning Machines

11

Filaments

From the

UNISILKON TK 017 THERM oil

series

Essential for testing and start-up of

precision gear pumps in the melt

spinning process

Klüberpaste HEL 46-450

or

WOLFRACOAT C

Well-proven hot screw thread

compound

UNISILKON TK 44 N 2 REC. A

UNISILKON L 50/2

BARRIERTA L 55/2

Excellent rolling bearing greases

with high thermal stability for long-

term lubrication

PETAMO GHY 441

Uniform viscosity for exact metering

adjustment and precise delivery

Low evaporation and sufficient resid-

ual oil for the start-up lubrication of

preheated pumps

Separating effect towards many

synthetic materials

The UNISILKON TK 017 THERM oils

are recommended e.g. by pump man-

ufacturers and successfully used by

numerous synthetic fibre processors.

Protection against seizure of spinerets

Easy removal

Easy dismantling of the spinerets

Klüberpaste HEL 46-450 and

WOLFRACOAT C are suitable for hot

screw threads up to 1200 °C.

Long-term lubrication and improved

bearing life under extreme conditions

Lubrication acc. to OEM recommendation,

e.g. by Starlinger

< 150 °C, PETAMO GHY 441

150 – 170 °C, BARRIERTA L 55/2

or Barmag: up to 180 °C

UNISILKON TK 44 N 2 REC. A

up to 200 °C: UNISILKON L 50/2

(cooperation: Starlinger – Windmöller + Hölscher)

Klübersynth BH 72-422


UNISILKON M 2000-SPRAY

Effective separating lubricant for

polymers during spinning start

No clogging of the spinerets and

secure start-up of production at tem-

peratures up to 180 – 200 °C max.

UNISILKON M 2000-SPRAY is a uni-

versal separating lubricant for thermo-

plastics and duroplastics as well as

elastomers and is also suitable as a

sliding agent for seals.

12

5.0


Cold and hot separator rollers

Spinning rings(sintered metal)

Thread breakage on fine denier caused by dragging

rollers; frequent maintenance

Production losses

Traveller and ring wear

Uneven or excessive yarn tension as well as lubricant

starvation

Filament coiling(after drawing)

High bearing loads resulting from high speeds up to

14,000 rpm

Lubricants for Synthetic FibreProcessing Machines

13

Filaments

ISOFLEX SUPER LDS 18/25 S

Lubricant dispersion system for

long-term lubrication

SYNTHESO XOL 12

Synthetic oil with an extraordinary

performance spectrum

Extremely smooth running, thus no

thread breakage; ensures years of

maintenance-free operation.

ISOFLEX SUPER LDS 18/25 S is a

CFC-free long-term lubricant (disper-

sion). Observe the solvent’s extended

evaporation period during relubrica-

tion.

Very low wear rates

Reduced yarn tension and optimum

distribution on the friction points

SYNTHESO XOL 12 is also suitable

for the lubrication of compressed air

tools.


ISOFLEX NBU 15

One of Klüber’s high-speed lubri-

cants that is being successfully

used worldwide

High operational reliability ensures

accurate coiling of the filament.

Filament coiling bearings are initially

lubricated with ISOFLEX NBU 15 by

Neumag.

14

6.0


Thread guide slides andzig-zag winding guides

Travelling knotter/splicer(Schlafhorst Autoconer®)

Spindle can bearing(see photo)

Belt guide rollers(no photo)

Wear

Yarn staining due to lubricant splashes

Excessive frictional temperature and

power requirement

High mechanical stress

Wear

Friction points difficult to access

Splicer(also knotter)

Flawed operation due to fibre build-up, contaminants

Impaired sliding effect

High energy consumption

Short relubrication intervals

Excessive frictional resistance of the grease

Impeded operation of guide rollers

Lubricants for Twisting and Spool Winding Machines

15

ISOFLEX TEL 3000 ALTEMP

Dynamically very light grease with

emergency lubricating properties

imparted by a light-coloured solid

lubricant compound

MOLYBKOMBIN M 5-SPRAY

Molybdenum disulphide lubricating

oil concentrate ensuring high wear

protection and emergency lubricat-

ing properties

UNIMOLY PLUS

Assembly paste for maintenance

operations


Dynamically light synthetic grease

for long-term or even lifetime

lubrication

STABURAGS N 4

A smooth running grease offering

an alternative to the above product

PETAMO GHY 133 N

Temperature reduction due to less

friction

Long maintenance intervals

Clean lubrication


is also suitable for thread guide

rails/boxes on flat bed knitting

machines.

Easy application by spraying

High protection against wear

Long-term effect

UNIMOLY PLUS for the ball cups on

the swivelling device, generally for the

lubrication of all sliding points and

connections after overhauling

MOLYBKOMBIN M 5-SPRAY is

approved for the lubrication of the

internal mechanism in the housing of

travelling knotters. It is also used for

the internal mechanism of the spool-

ing equipment and for gears in the

gear reducer unit of the travelling

splicer or travelling knotter.

Substantial reduction of power

requirement

Extended relubrication intervals of

5000 h or more

Relubrication interval: up to 10,000

operating hours


is a special grease for high speeds

ensuring uniform speed.

STABURAGS N 4

ensures low-friction guiding of drive

belts.


QUIETSCH-EX SPRAY

is a low-viscous lubricant, corro-

sion protective and rust removing

agent.

Preventive maintenance with a com-

bined cleaning and oil spray. The ultra-

thin oil film ensures the necessary

wear protection, excellent surface

wetting and protection against corro-

sion.

QUIETSCH-EX SPRAY

is also used for guide bars on knitting

machines and for the Jacquard nee-

dles of looms.

An ultra-thin layer ensures efficientlubrication.

16

7.0


Lid seals of dyeing vessels(see photo)

and

yarn steamers(no photo)

Worm gear of overheadtravelling cleaners

Sticking of rubber seals results in excessive seal wear.

Excessive temperature due to high frictional heat

Lubricant leakage

Contamination and severe wear

Lubricants for Apparatuses and Special Machines

17

SYNTHESO PROBA 270

Fully synthetic grease with neutral

properties towards natural and

synthetic rubber

STRUCTOVIS P LIQUID

Synthetic, intrinsically viscous lubri-

cant improving gear efficiency

Due to the sliding film the lids open

and close easily and the seals reach

an extended service life.

Seal relubrication only required weekly

SYNTHESO PROBA 270

The water and steam resistant grease film

is also an ideal assembly aid for all rubber

seals and in the finishing section.

For lubricating bearings in the washing

liquor circulation pumps,

STABURAGS NBU 12/300 KP (Thies)

or

PETAMO GHY 133 N (Then) are recom-

mended

Prevents leaks on shaft seals.

Low gear temperature, suitable for

long-term lubrication

STRUCTOVIS P LIQUID

is recommended for gearboxes that

are not oil-tight.


18

8.0


Needles and sinkers in circular knittingmachines

Flat bed knittingmachines

Application in stitch-

forming elements

Slide rails on flat bedknitting machines,thread guide box

Overheating in the knitting section

Production malfunctions caused by wear resulting in

formation of stripes as well as problems due to insuffi-

cient scouring of the textile machine oils from the knit-

ted fabrics

Neutral towards elastane fibres and elastomers

Hosiery knittingmachines

Application in

stitch-forming elements

and gears

Temperature increase in high-speed machines, along

with increased wear

Neutral towards elastane fibres and elastomers

Drops or splashes of lubricant caused by the sudden

arrest of the thread guide box on reaching its stop as

well as frequent dragging motion

Lubricants for Knitting Machines

19

Running-in oil:Klüber Silvertex P 91

Needle oil:Klüber Silvertex W 22/W 32Klüber Silvertex T 22/T 32Klüberoil TEX 1-22 N/1-32 N

Cleaning oil:Klüber Silvertex R 14/R 20


Needle oil:Klüber Silvertex W 32Klüber Silvertex T 32/T 46Klüberoil TEX 1-32 N/1-46 N

Cleaning oil:Klüber Silvertex R 14/R 20

Klüber Silvertex GREASE 3000 N


Light-coloured, soft sliding greases

replacing oil lubrication

Klüber needle oils reduce the operat-

ing temperatures and protect against

wear and corrosion of the stitch-form-

ing elements, thus reducing mainte-

nance costs of production machines.

They are scourable and neutral

towards elastane fibres and elas-

tomers. Klüber needle oils have been

tested and approved by knitting

machine manufacturers worldwide.

For instance, they are used for initial

lubrication by Mayer & Cie., Terrot,

Stoll and Universal.

There is no universal method to

remove oil stains from the different

types of knitting materials or fibre

mixtures. In consequence, close

cooperation between the knitting and

the finishing sections is required when

selecting a suitable detergent.

Relubrication is usually necessary only

once a week and looping of the thread

is avoided in Jacquard equipment.



for slide rails where smooth sliding

operation is of primary importance



Needle oil:TEX SYNTHESO M 32 NTEX SYNTHESO M 46 NKlüber Madol 172Klüber Madol 183

Cleaning oil:Klüber Silvertex R 14Klüber Silvertex R 20

20

9.0


Friction gears

Guide bars in warp knitting machines

Insufficient traction, non-uniform operation of the gear

Contamination of fabrics and frequent maintenance

work between warp beam changes resulting from

insufficient adhesion and insufficient life of the lubri-

cant film

Lubricants for Warp Knitting Machines

21

FORMINOL DS 23 K

or as a synthetic, long life oil and

super traction fluid

LAMORA VARIOGEAROIL EL 2

QUIETSCH-EX SPRAY

for flat bed frames

and


or

ALTEMP Q NB 50

for ball joint bushes

These gear oils ensure optimum gear

operation, thus allowing precise

thread feed and fabric take-up.

They are indispensable for producing

top-quality fabrics.

FORMINOL DS 23 K and


are recommended by the leading

machine manufacturers.

The performance of these lubricants

lasts at least from one warp beam

change to the next, so trouble-free

production is guaranteed due to the

long-lasting effect and good adhesion

to the friction points.

QUIETSCH-EX is also an excellent

corrosion preventive and rust removal

agent.

Klüberpaste 46 MR 401 and

ALTEMP Q NB 50

also are universal lubricating and

assembly pastes preventing fretting

corrosion.


22

10.0


Bearings of drying cylin-ders and calender rollersin sizing dryers

Gripper looms(tape gripper looms)

Open gears and chains

If mineral-oil-based lubricants are used, high bearingtemperatures (drying cylinders up to max. 165 °C)result in short lubrication intervals and/or increasedresidue formation.

Rolling bearings subject to vibrations, especially in theflywheel support and the crosshead axle

Motor coupling withbrake and sliding block

Rapier guide roller anddistributor cutter

Short oil change intervals in tape driveWeaving machine gears

Dragging motion

Tape grippers of gripper looms

High friction and wear as well as contamination of thewoven fabric by pasty and fluid lubricants

Dripping and splashing of the lubricant, short relubri-cation intervals and thus high maintenance require-ments and wear problems

Furthermore, contamination of the workplace and dis-turbing noise level due to insufficient damping orlubricating effect

Lubricants for Sizing Machines and Looms

23

SYNTHESO D 220Synthetic high-temperature oil.Suitable up to 150 °C and shortpeaks up to 180 °CFor grease lubrication:STABURAGS NBU 30 G 5(contains solid lubricant particles;e.g. for older types of sealing units)

STABURAGS NBU 12 (no solid particles; for cylinderbearings in the sizing section)

MICROLUBE GBU Y 131

or

STABURAGS NBU 12 ALTEMP

White special lubricant (containssolid lubricant particles) with a highpressure absorption capacity

GRAFLOSCON CA ULTRA-SPRAYAdhesive lubricant with graphite anda synergetic additive package sup-plied in a convenient aerosol can

HOTEMP 2000-SPRAYVery adhesive, high-performance oil,resistant to high temperatures, goodpenetration

SYNTHESO D 220 has excellent lubricating properties.

Compared with mineral oil, residueformation is substantially lower, and oilchange intervals can be extendedconsiderably (3 to 5 times longer).

SYNTHESO D 220 is recommendedfor sizing dryers. Calender manufac-turers recommend it for oil-lubricatedrolling and plain bearings subject tohigh thermal stress.

MICROLUBE GBU Y 131 allowsextension of relubrication intervals toone month, even at extremely highspeeds.

STABURAGS NBU 12 ALTEMP provides reliable protection againstfretting corrosion.

MICROLUBE GBU Y 131 has an

excellent backflow behaviour, which is

especially important in friction points

subject to oscillating motion.

This lubricant is recommended by

Sultex (Sulzer Textil).

Excellent wear protection combinedwith high adhesion allow extremelylong relubrication intervals.

Chain and gear lubricant, very adhe-sive, which prevents splashing, gooddamping properties. Suitable for sprayheads with point and wide-jet applica-tion

GRAFLOSCON CA ULTRA-SPRAY isan ideal lubricant for open gears. Well-metered application on drive chainsensures minimum adhesion of lint anddust.

HOTEMP 2000-SPRAY is a universalchain spray – also suitable for drive,control and transport chains runningat high speeds.


SYNTHESO D 150 EP orSYNTHESO D 100 EP (dependingon weaving machine type) Fully synthetic gear oils with highpressure absorption capacity forextreme loads

Longer oil change intervals: approx.15000 op. hrs. instead of approx.5000 op. hrs. (mineral oil)

Recommended by VAMATEX for tapegripper and terry looms

For further information on gear lubri-cation see p. 30/31.

ISOFLEX TOPAS NB 52

ISOFLEX ALLTIME SL 1

Both ISOFLEX types are smooth-run-ning greases with operational reliabilityand long service life.

Recommended for weaving machinesby Sauer-Diederichs

ALTEMPAN POBWhite lubricant powder with extraordi-nary sliding characteristics; consump-tion approx. 1 g per 24 h per machine

This lubricating powder eliminates therisk of contamination and increasesthe service life of the gripper tapes byup to 100 %.

ALTEMPAN POB has been success-fully used for bobbins in bobbinetweaving for many years.

24

11.0


Rolling bearings in wash-ing and mercerisingmachines, dyeingmachines and festoonsteamers

Corrosion protection for the inner lining ofsteamers

Chains in steamers

Bearings in steamers

Bearing failures due to corrosion

Washing-out of the grease from the bearings bydetergents, processing fluids and splash water

Corrosion of steel lining resulting from severe mediaattack

Reduced production and increased costs for repair

Fabric conveyor chains

Condensates from softeners and finishing materials

Increased deposits at temperatures above 160 °C,resulting in dragging chain links, chain rattle and thusexcessive power consumption

Lubricants for Textile Finishing Machines

25

STABURAGS NBU 12 or 30STABURAGS NBU 12 / 300 KPWater and steam resistant specialgrease, which is also resistant toaqueous alkaline and aqueous acidsolutions

The lubricating grease has goodsealing properties and protectsbearings against corrosion.Alternatively: Klüberplex BE 31-222

STABURAGS NBU 30A hot-water, steam, alkali and acidresistant special grease, ideal for theinternal protection of steamers

High-temperature chain oils:Klübersynth CTH 2-260 orPRIMIUM FLUID SPECIAL orHOTEMP PLUS

UNISILKON L 50/2Alternatively: UNISILKON GLK 112

High operational reliability and resist-ance to water, hot water, aggressivevapours and many other mediaencountered in textile finishing

Good corrosion protection and longrelubrication intervals

STABURAGS NBU 12 or 30


are special high-pressure and long-term greases for all lubrication pointsexposed to media.

STABURAGS NBU 30 is a reliable andeconomical long-term protection, as itprovides an internal coating which lastsfor one year or more in most cases.Premature expensive replacement ofthe steamer lining is, consequently, notnecessary.

Note: New steamer wall materials mayrequire a different long-term protectionagent.

STABURAGS NBU 30 is a speciallong-term grease with excellent seal-ing properties suitable for low-speedrolling and plain bearings in wet pro-cessing machines.

It is applied according to the recom-mendations of the machine manufac-turers.


For sliding chains:Klübersynth CTH 2-260Fully synthetic high-performancechain oil for high temperatures orHOTEMP PLUSabove 200 °C orPRIMIUM FLUID SPECIAL

Grease lubrication for chains sup-ported by ball bearings:BARRIERTA L 55/2 for long-term lubrication or in acc.with manufacturer’s instructions. Long-term lubricated bearingshave a different design requiringlower relubrication quantities. Alternative for long-term lubrica-tion:Klübertemp HM 83-402UNISILKON L 50/2

For oil lubrication:HOTEMP PLUS

Separating effect on condensatesand, consequently, less build-up ofresidues. Efficient lubrication of thechain links, rolling bearings and sliderails under varying operating condi-tions (speed, temperature, stretchingtension). Low power consumptionwith practically wear-free operation

Synthetic sliding surfaces on stenterchains with special lubricant require-ments in terms of evaporation, forma-tion of residues, regenerative capacity,friction and wetting behaviour resultedin the development of KlübersynthCTH 2-260.

This special chain oil meets all require-ments and has a considerably betterviscosity-temperature behaviour thanprevious standard chains oils.

Klüber Lubrication high-temperaturechain oils for operating temperaturesup to 250 °C are recommended for alloil-lubricated chain systems in stenterframes, drying and setting machines,multi-layer systems, festoon steamers,steamers, condensers and coatinginstallations by leading machine manu-facturers.

26

11.0


Chains in dryers forprinted fabrics(in combination with the

printing machine)

Needle bars, clip tables

Rolling bearings in fansand exhaust fans in dryers(direct drive)

Deposits of condensates

Formation of residues at a temperature above 160 °C

Dragging chain links, chain rattle and excessive

power requirements

Contamination of the fabric by deposits of burnt-on

softeners and condensed finishing compounds

Extensive cleaning work

Rolling bearings of electric motors in dryers(indirect drive)

Cracking and carbon residues, as well as the loss of

grease due to high temperatures

Bearing wear and premature bearing failures

Increased maintenance and repair costs


27

HOTEMP PLUS

Fully synthetic, high-performance,

high-temperature chain oil or

PRIMIUM FLUID SPECIAL

or

STRUCTOVIS BHDup to 120 °C


or

UNISILKON TK 002/100for semi-automatic application via

drip feed oilers or rotating brushes

Separating effect on condensates

and, consequently, less build-up of

residues

Efficient lubrication of the chain links

at high operating temperatures

Low energy requirement of the

machine and virtually wear-free

operation

High-temperature chain oils produced

by Klüber Lubrication are recommend-

ed for all oil-lubricated chain systems

and fully meet the requirements of

chain and machine manufacturers and

operators.

Smooth opening and closing of clips

ensured by small lubricant quantities

(acting as release agent), which keeps

needle bars and clip tables clean

Regular application of the release

agent to low-speed clips or needle

bars ensures an optimum separatingeffect.

Expressly recommended by

MONFORTS


STABURAGS N 12 MFHigh-temperature and long-term

grease with emergency lubricating

properties imparted by MoS2 solid

lubricant compound

or

according to the recommendation

of other manufacturers, e.g.

PETAMO GHY 133

UNIMOLY GB 2

MICROLUBE GNY 202

Klüberplex BEM 34-132< 150 ºC (Brückner)

Long relubrication intervals

Wear protection under boundary

friction conditions

Reliability at high operating tempera-

tures

STABURAGS N 12 MF for the lubrica-

tion of fan bearings. Exclusively rec-

ommended and time-tested for the

lifetime lubrication of electric motor

bearings

Also suitable for rolling bearings on

chain return wheels as well as grease

lubrication of splined shafts. The syn-

thetic lubricating greases

UNISILKON L 50/2

and

BARRIERTA L 55/2

offer sound technical and economical

solutions to applications with bearing

temperatures in excess of 150 °C,

especially for long-term and lifetime

lubrication.

28

11.0


Width adjustment spindles

Rolling and plain bearings in heated calenders

Compensator and guideroller bearings in Hotfluefinishing machines

Heavy build-up of contaminants with lubricating oils

or greases, as well as carbon and cracking residues

that may impede motion

In heated calenders the oil’s operating viscosity

is too low.

Mineral oils may cause the formation of residues, thus

short oil change intervals required.

Rotary couplings e.g. insteam-heated finishingmachines

Excessive seal wear due to inadequate lubrication of

the rolling bearings at temperatures up to 180 °C and

above

Relubrication intervals too short

Drying-out of the lubricating grease due to extreme

thermal influences


29

MOLYBKOMBIN UMF T 4 – SPRAY

Molybdenum disulphide bonded

coating, providing a dry lubricating

film up to 450 °C

or according to manufacturer’s

special recommendation:

UNISILKON L 50/2

UNISILKON GLK 112

SYNTHESO D oils

Fully synthetic high-temperature

oils with good viscosity-tempera-

ture characteristics

Largely prevents the build-up of lint

and contamination. Consequently,

easy and accurate width adjustment is

possible requiring comparatively little

maintenance.

MOLYBKOMBIN UMF T 4 – SPRAY is

ideal in workshops for assembly pur-

poses, e.g. screwed connections and

bearing seats.

Protects against seizure, especially at

high temperatures.

Can be delivered through oil pumps

and pipe systems, also at room tem-

perature. At higher temperatures up to

150 °C or short peaks up to 180 °C

(maximum film temperature 225 °C)

SYNTHESO D oils have a higher oper-

ational viscosity than mineral oils of a

similar ISO viscosity grade and fulfil

the demands for the required full fluid-

film lubrication.

To suit the recommendations of

machine manufacturers SYNTHESO D

oils are available in all common ISO

viscosity grades.

ISO viscosity grades 220, 460 and

1000 are recommended.


PETAMO GY 193

at temperatures up to 180 °C;

BARRIERTA L 55/2

or

Klübertemp HM 83-402

at temperatures above 180 °C;

Alternatively:


Particularly good resistance to

aggressive media

High wear protection

Good sealing effect

Klübertemp HM 83-402,

PETAMO GY 193 and

BARRIERTA L 55/2

are expressly recommended by

Messrs. Maier Heidenheim.

STABURAGS NBU 30 G 5 is used in

older types of sealing units.


or

BARRIERTA L 55/2

Synthetic high-temperature

lubricating greases

Alternatively:


Very good resistance to aggressive

media and temperatures

Excellent lubricating properties

Klübertemp HM 83-402 and

BARRIERTA L 55/2

are also suitable for wear protection of

electrical contacts and suitable for the

lubrication of sliding material combi-

nations, i.e. plastic to plastic.

30

12.0


Spur and bevel gears

Rolling bearings in electric motors

High temperatures lead to rapid oil ageing and short

oil change intervals.

Extremely high specific flank pressure under mixed

friction conditions (e.g. with high torques at low

speeds)

Worm gears Excessive oil sump temperature

Rapid oil ageing and short oil change intervals

Excessive wear of wheel resulting in low efficiency

Premature bearing failure resulting in machine

downtime

Lubricants for Gear Units and Electric Motors in Textile Machines

31

Oil series:

Klübersynth EG 4 oils

High-performance gear oils on a

PAO basis

SYNTHESO D ... EP oils

Synthetic gear oils for extreme

loads on a PG basis

Other alternatives:

Klübersynth 100 KV(Klübersynth GE 4 75 W 90)Klübersynth G 4-130

(see Notes)

Good friction behaviour resulted in

gear temperature reduction by 10 °K

or more. Oil change intervals are at

least three times as long as those of

mineral oils.

Klübersynth EG 4 oils are available in

all common ISO viscosity grades.

They are miscible with mineral oil and

show mostly neutral behaviour

towards paints and seals.

SYNTHESO D ... EP oils are not misci-

ble with mineral oils or oils on a PAO

basis. We recommend testing com-

patibility with sealing materials, paints

and inspection glass.

The optimum choice for gear lubrica-

tion in weaving machines if long oil life

is desired. Approvals by several man-

ufacturers, e.g. by VAMATEX NUOVA

for Klübersynth 100 KV and by

SOMET for Klübersynth G 4-130

(for relubrication)


Klübersynth GH 6 oils

High-performance gear oils on a

PG basis

Alternatively:

Klübersynth EG 4 oils

(see above)

or

STRUCTOVIS BHD MF

Klübersynth GH 6 oils have an excel-

lent friction behaviour. They reduce

gear temperatures considerably and

increase gear efficiency by more than

25 %. Owing to their special additives

they reduce wear substantially, espe-

cially on materials that are typically

used for worm gears. Oil change inter-

vals are at least five times longer than

those of mineral oils.

STRUCTOVIS BHD MF is an intrinsi-

cally viscous long-term and high-tem-

perature lubricant. It contains solid

lubricant particles and is especially

suitable for worm gear drives of width

adjustment spindles.

Klübersynth GH 6 oils are available in

all common ISO viscosity grades.

They are not miscible with mineral oils

or oils on a PAO basis. We recom-

mend testing compatibility with seal-

ing materials, paints and inspection

glass.

BRÜCKNER recommend

STRUCTOVIS BHD MF for the lubrica-

tion of worm gears in stenters.

Klüberquiet BQH 72-101, BQ 72-72for long-term and lifetime lubrica-

tion mostly of rolling bearings that

do not allow relubrication running

at > 100 °C and high speeds

For rolling bearings that can berelubricated:

Klüberplex BEM 41-132

Klüberquiet greases are characterized

by a wider service temperature range

and an extremely high resistance to

temperature and speed.

At high temperatures, runtimes

> 4000 hours are possible without

relubrication; the same applies to

Klüberplex BEM 41-132 at low tem-

peratures.

Klüberquiet/Klüberplex greases meet

most requirements to be satisfied by

today’s rolling bearing lubricants.

Our tried-and-tested greases

STABURAGS N 12 MF and

STABURAGS NBU 8 EP continue to

be good choices for many applica-

tions.

32

High-Pressure Stage

13.0


Screw-type compressor

Rotary vane compressor

High operating temperatures leading to rapid oil

ageing through oxidation, and short oil change

intervals

High operating temperatures leading to rapid oil

ageing through oxidation, and short oil change

intervals

Coking of the oil leads to formation of residues.

Cleaning of screw-typeand rotary vane com-pressors

(before)

(after)

Deposits due to pronounced oxidation especially of

mineral-oil-based products

This will inevitably lead to contamination of the new oil

fill unless the compressor is cleaned during

changeover.

Lubricants for Compressors in the Textile Industry

33

Klüber Summit SH oils

High-performance compressor oils

on a PAO basis

Klüber Summit DSL oils

High-performance compressor oils

on a diester basis

Clean compressor thanks to good

oxidation stability

Oil change intervals at least three

times longer than those of mineral oils

When changing over from mineral oils,

energy cost cuttings by 3 to 5% are

possible.

Klüber Summit SH oils are available in

all common viscosity grades. They are

miscible with any residual mineral oil in

the compressor and are mostly neutral

towards paints and seals.

Low tendency towards residue forma-

tion reduces deposits and gluing of

vanes.

Oil change intervals at least three

times as long as those of mineral oils

When changing over from mineral oils,

energy cost cuttings by 3 to 5% are

possible.

Klüber Summit DSL oils are available

in all common viscosity grades.

Compatibility with seals and paints

should be tested.


Concentrated compressor

conditioner

Klüber Summit VARNASOLV

Concentrated conditioner for cleaning

screw-type and rotary vane compres-

sors, especially when changing over

from mineral-oil-based products to the

synthetic Klüber Summit DSL or SH oil

Klüber Summit VARNASOLV is added

to the oil fill at a concentration of 10 %

and should remain in the compressor

for 40 to 60 operating hours.

Then drain the compressor while the

oil is still hot.

When used at a concentration of

10 %, VARNASOLV is compatible with

all materials resistant to mineral oil.

The oil ageing condition can be visual-

ly inspected (preferably before oil

change) by means of the

Klüber Summit TAN kit.

34

14.0

Highly efficient lubricating oil on a mineral hydrocarbon basis for friction

gears

Synthetic high-temperature chain oil, retards wear, spreads easily and

adheres excellently

Very adhesive, fully synthetic high-temperature chain oil;

solvent: hydrocarbon; propellant: propane-butane

Instrument oil for a wide service temperature range

Needle and sinker oil for hosiery knitting machines with anticorrosive and

antiwear effect; dampens vibration and noise; for oil circulating systems

Special running-in oil with a synthetic ester basis for problem-free running-

in of knitting machines, especially at low ambient temperatures (new or

overhauled machines)

Special cleaning oil for stitch-forming elements in circular, flat-bed and

hosiery knitting machines; dissolves contaminants such as yarn dust, fibre

particles and paraffins during machine operation

Special cleaning oil for stitch-forming elements in circular, flat-bed and

hosiery knitting machines; dissolves contaminants such as softening

agents from synthetic fibres or unsuitable needle and sinker oils during

machine operation

High-performance needle and sinker oil for the knitting industry; based on

universal and synthetic oils; scourable with customary washing liquors

High-performance needle and sinker oil with a mineral oil basis; scourable

with customary washing liquors; compatible with elastane fibres

Synthetic compressor oil with excellent low-temperature behaviour; espe-

cially for application in screw-type compressors

Synthetic compressor oil with reduced deposit formation; preferred choice

for piston and rotary vane compressors

Synthetic high-performance gear oil with excellent load-bearing capacity

and viscosity-temperature behaviour for use in weaving machines

Synthetic high-performance gear oil without additives for use in weaving

machines; neutral towards nonferrous metals such as brass, bronze, copper

Synthetic long-term gear oil on a PAO basis with very high scuffing load

capacity (GL 5) for use in weaving machines

Fully synthetic high-temperature oil for oil-lubricated stenter chains; effi-

cient lubrication also at high operating temperatures; low evaporation

losses; spreads and penetrates easily, also when used on chains with plas-

tic sliders

Klüber products

FORMINOL DS 23 K

HOTEMP PLUS

HOTEMP 2000-SPRAY

ISOFLEX PDP 65

Klüber Madol 172Klüber Madol 183

Klüber Silvertex P 91

Klüber Silvertex R 14

Klüber Silvertex R 20

Klüber Silvertex T 22 / T 32 / T 46

Klüber Silvertex W 22 / W 32

Klüber Summit SH 32…100

Klüber Summit DSL 32…125

Klübersynth 100 KV

Klübersynth G 4-130

Klübersynth GE 4 75 W 90

Klübersynth CTH 2-260

Application notes

Product Overview14.1 Lubricating Oils

Please order further information on the a.m. products

35

Fully synthetic high-performance gear oils for cylindrical, bevel and worm

gears; they are miscible with mineral oils and almost neutral towards

commercial sealing materials and paints; these oils offer good wear and

corrosion protection, as well as resistance to ageing and oxidation; in the

FZG test (A 10/16,6R/90) they achieve the scuffing load stage GL 4.

High-performance gear oils on a polyglycol basis with a high scuffing load

stage and good protection against wear; in the stringent FZG test

A/16.6/140 they achieve a scuffing load stage > 12 and a work-related

change in weight < 0.2 mg/kWh; GH 6 oils are particularly resistant to age-

ing and oxidation, they have a good viscosity-temperature behaviour and

are especially suitable for high-temperature lubrication1) (up to 150 °C, oil

sump temperature > 100 °C). Developed for the lubrication of steel/bronze

worm gears, GH 6 oils are also suitable for the lubrication of all types of

spur and bevel gears; Klübersynth GH 6 oils are not miscible with mineral

or PAO oils; we recommend testing compatibility with sealing materials,

paints and inspection glass.

Traction fluid for infinitely variable frictional control gears made of soild

steel

Fully synthetic high-temperature chain oil

Thin-bodied universal fluid on a mineral hydrocarbon basis ensuring excel-

lent wetting and penetration; suitable as a lubricant, rust dissolving and

anticorrosion agent; free from solvents

Intrinsically viscous long-term and high-temperature lubricant on the basis

of mineral oil and synthetic hydrocarbon oil

Intrinsically viscous long-term and high-temperature lubricant on the basis

of mineral oil and synthetic hydrocarbon oil; contains solid lubricant parti-

cles (MoS2)

Synthetic high-temperature lubricating and heat transfer oil on a PAG

basis; not miscible with mineral and PAO oils; we recommend testing com-

patibility with sealing materials, paints and inspection glass.

High-performance gear oils for the lubrication of spur and bevel gears

operating under extreme loads; also suitable for hypoid gears; the oil of

ISO VG 220 passes the FZG-L-42 test (hypoid gear test); not miscible with

mineral and PAO oils; we recommend testing compatibility with sealing

materials, paints and inspection glass.

Mineral-oil-based antiwear needle and sinker oils; scourable with custom-

ary washing liquors

Klüber products

Klübersynth EG 4-150Klübersynth EG 4-220Klübersynth EG 4-320Klübersynth EG 4-460Klübersynth EG 4-680Klübersynth EG 4-1000

Klübersynth GH 6-32Klübersynth GH 6-80Klübersynth GH 6-100Klübersynth GH 6-150Klübersynth GH 6-220Klübersynth GH 6-320Klübersynth GH 6-460Klübersynth GH 6-680Klübersynth GH 6-1000


PRIMIUM FLUID SPECIAL

QUIETSCH-EX UNIVERSAL FLUID-SPRAY

STRUCTOVIS BHD

STRUCTOVIS BHD MF

SYNTHESO D 220

SYNTHESO D 100 EPSYNTHESO D 150 EPSYNTHESO D 220 EP

TEX SYNTHESO M 32 NTEX SYNTHESO M 46 N

Application notes

1) see page 39Please order further information on the a.m. products

36

Klüber products

Klüberoil TEX 1-22 NKlüberoil TEX 1-32 NKlüberoil TEX 1-46 N

Klüber Summit VARNASOLV


UNISILKON TK 002 / 100

UNISILKON TK 017 / 200 THERM (as example)

BARRIERTA L 55 /2

GRAFLOSCON CA ULTRA-SPRAY

ISOFLEX ALLTIME SL 1


ISOFLEX NBU 15

ISOFLEX NCA 15

ISOFLEX SUPER LDS 18 / 25 S

Application notes

14.2 Release agents

Please order further information on the a.m. products

Anti-wear and biodegradable needle and sinker oils; good scourability with

commercial washing liquors, protect against corrosion, dampen oscillation

and noise, compatible with elastane fibers

Concentrated compressor conditioner; reliably dissolves varnish and

carbon build-ups during operation

Clear silicone film, free from solvents; suitable as a release agent to prevent

softening or finishing agents from sticking to needle bars and clip tables

Colourless, clear synthetic oil on a methyl silicone oil basis; suitable as a

release agent to prevent softening or finishing agents from sticking to

needle bars and clip tables

Lubricating oil on a methyl phenyl silicone oil basis with an excellent resist-

ance to high temperatures; no polymerization after 1000 h at 250 °C1)

High-temperature lubricating grease, resistant to water, extremely resistant

to oxidation, not aggressive towards most elastomers and plastics, not

corrosive towards ferrous and nonferrous metals, resistant to most chemi-

cals and organic solvents (also to CHC solvents); not resistant to

fluorinated hydrocarbon solvents

Adhesive spray lubricant with a high solid lubricant content (fine graphite),

CFC-free, contains solvent; suitable for small open spur and bevel gear

stages and for the external lubrication of chains; good absorption of high

pressure, good anticorrosion properties; thermal load carrying capacity,

depending on relubrication, up to approx. 200 °C1)

Dynamically light rolling bearing grease for high speeds and a wide service

temperature range

Dynamically light grease for plain and rolling bearings subject to high

speeds; good pressure absorption capacity

Lubricating grease for plain and rolling bearings subject to high speeds;

good pressure absorption capacity

Lubricating grease for plain and rolling bearings, especially for spindle and

taper roller bearings subject to very high speeds

Dynamically light grease for plain and rolling bearing subject to high

speeds; dispersed in a solvent (aliphatic hydrocarbon) for easier

application

14.3 Lubricating greases

1) see page 39

37

Sliding grease for friction points in textile machines and optical equipment

Plain and rolling bearing grease for a wide service temperature range,

excellent resistance to water, good pressure absorption capacity

Fully synthetic lubricating grease manufactured under clean-room condi-

tions, hence very high purity and low noise; for use at up to 180 °C1)

Lubricating grease forming a lubricating film of high mechano-dynamical load resi-

stance; very good wear protection and resistance to aggressive media; sealing effect

Special grease offering high resistance to water and aggressive media

Special grease offering good high-temperature resistance1) (up to 150 °C)

as well as wear and corrosion protection

High-performance grease for lubrication of carriage guides and the bases

of needle and selection slides

Long-term and high-temperature grease for slow moving rolling bearings,

plain bearings and slideways; operating temperature1) up to 220 °C; friction

points can be cleaned with organic solvents

High-temperature and long-term grease with a fully synthetic basis; neutral

towards a large number of plastic materials, especially FKM; high resist-

ance to chemicals and aggressive media

Low-noise rolling bearing grease for long-term lubrication; very good com-

patibility with elastomers and excellent low-temperature behaviour

Long-term grease for plain and rolling bearings to prevent tribocorrosion;

suitable for high temperatures, very adhesive, resistant to oxidation, pro-

longed working and water; excellent pressure absorption capacity and

good protection against corrosion

High-temperature grease for plain and rolling bearings

Long-term and high-temperature grease for rolling bearings in electric

motors, high-temperature fans, driers, textile machinery

High-temperature grease for rolling bearings

High-temperature grease with synthetic base oil for plain and rolling bea-

rings; good pressure absorption capacity

Smooth-running grease for long-term lubrication e.g. of belt guiding rollers

High-temperature long-term or lifetime grease for encased rolling bearings

that are not relubricated, especially for electric motors; good emergency

lubrication properties owing to the MoS2 solid lubricant combination

Long-term grease for plain and rolling bearings; suitable for high tempera-

tures, resistant to hot water, good pressure absorption capacity

Klüber products


ISOFLEX TOPAS NB 52

Klüberquiet BQH 72-102

Klüberplex BE 31-222






Klüberquiet BQ 72-72

MICROLUBE GBU Y 131

MICROLUBE GNY 202

PETAMO GHY 133 N

PETAMO GY 193

PETAMO GHY 441

STABURAGS N 4

STABURAGS N 12 MF

STABURAGS NBU 12

Application notes

Please order further information on the a.m. products 1) see page 39

38

Lubricating grease for plain and rolling bearings, especially for lubrication

points subject to external vibrations or oscillations

Long-term grease for plain and rolling bearings; suitable for high tempera-

tures, resistant to hot water, good pressure absorption capacity

Adhesive grease, resistant to steam, good pressure absorption capacity;

suitable as a valve and sealing grease for plain and rolling bearings operat-

ing at low speeds

Adhesive grease, resistant to steam, good pressure absorption capacity;

suitable as a valve and sealing grease for plain and rolling bearings operat-

ing at low speeds

Fluid grease with a wide service temperature range; especially suitable for

splash lubrication of steel/bronze worm gears; universally suitable for long-

term and lifetime lubrication

Valve and bearing grease for hot water valves and rubber seals, e.g. in

autoclaves and HT dyeing installations; resistant to water and oxidation;

protects against corrosion

Emulsifiable and scourable grease for ring travellers

High-temperature grease for rolling bearings; especially suitable for electric

motors, fans, chain wheel bearings

Silicone grease for a service temperature range1) between – 50 °C and

180°C; good wetting of surfaces

Lubricating grease for plain and rolling bearings with a wide service tem-

perature range; protects against seizure at high temperatures

Rolling bearing grease containing solid lubricant particles; suitable for

increased loads and for emergency lubrication in case of surface pressure

or sliding friction

Klüber products

STABURAGS NBU 12 ALTEMP


STABURAGS NBU 30

STABURAGS NBU 30 G 5

STRUCTOVIS P LIQUID

SYNTHESO PROBA 270

TEX SYNTHESOTRAVEL 45WEISS A

UNIMOLY GB 2

UNISILKON GLK 112

UNISILKON L 50 / 2

UNISILKON TK 44 N 2 REC A

Application notes

Please order further information on the a.m. products 1) see page 39

39

1) Service temperatures are guide values which depend on the lubricant’s composition, the intended use and the application method. Lubricantschange their consistency, apparent dynamic viscosity or viscosity depending on the mechano-dynamical loads, time, pressure and temperature.These changes in product characteristics may affect the function of a component.

The data in this technical brochure is based on our general experience and knowledge at the time of printingand is intended to give information of possible applications to a reader with technical experience. It consti-tutes neither an assurance of product properties nor does it release the user from the obligation of per-forming preliminary tests with the selected product. We recommend contacting our Technical Consult-ing Staff to discuss your specific application. If required and possible we will be pleased to provide asample for testing. Klüber products are continually improved. Therefore, Klüber Lubrication reservesthe right to change all the technical data in this technical brochure at any time without notice.

Publisher and design: Klüber Lubrication München KG

Copyright: Klüber Lubrication München KG

5.49 e, edition 07.03

replaces edition 04.99

Reprints, total or in part, are permitted if source is indicated

and a voucher copy is forwarded.

Light-coloured multi-purpose and assembly paste reducing stick slip and

fretting corrosion

“White” multi-purpose paste with a very high pressure absorption capacity;

prevents tribocorrosion and protects against corrosion

Assembly paste on a synthetic oil basis; free from heavy metals and halo-

gen; service temperature range1) – 40 °C to 1000 °C; above 200 °C dry

lubrication, below 200 °C excellent corrosion protection

Multi-purpose and assembly paste, e.g. for the initial lubrication of sliding

points and joints after maintenance

High-temperature compound, release and sliding agent for screws, guide-

ways, gates and low-speed plain bearings

Klüber products

ALTEMP Q NB 50


Klüberpaste HEL 46-450

UNIMOLY PLUS

WOLFRACOAT C

White lubricating powder for weaving machines

Solid lubricant suspension in mineral oil supplied as a spray; solvent:

hydrocarbon; propellant: propane-butane

Solid lubricant with binding agent for spray lubrication of threaded spindles

in stenters; solvent: acetone; propellant: dimethyl ether

ALTEMPAN POB

MOLYBKOMBIN M 5-SPRAY

MOLYBKOMBIN UMF T 4-SPRAY

Application notes

14.4 Lubricating pastes

Please order further information on the a.m. products.

14.5 Solid lubricants

Klüber Lubrication München KGGeisenhausenerstraße 781379 MünchenGermany� +49 89 7876-0Telefax +49 89 [email protected]

Klüber Lubrication AustriaGes.m.b.H.Franz-Wolfram-Scherer-Straße 32Postfach 845028 Salzburg-KasernAustria� +43 662 452705-0Telefax +43 662 [email protected]

Klüber Lubrication BeneluxS.A./N.V.Rue Cardinal Mercier 1007711 DottigniesBelgium� +32 56 483311Telefax +32 56 [email protected]

Klüber Lubrication CZ s.r.o.Prazakova 1061900 BrnoCzech Republic� +420 5 43424836-7Telefax +420 5 [email protected]

Klüber Lubrication Skandinavien A/SLiterbuen 92740 SkovlundeDenmark� +45 70 234277Telefax +45 70 [email protected]

Klüber Lubrication SkandinavienA/S, Filial FinlandMartinkyläntie 6701720 VantaaFinland� +358 9 8545610Telefax +358 9 [email protected]

Klüber Lubrication France S.A.S.Z.I. des Auréats,10 à 16 Allée E. Ducretet26014 Valence CedexFrance� +33 4 75448436Telefax +33 4 [email protected]

Klüber Lubrication Italia S.a.S.Via Monferrato 57, Sesto Ulteriano20098 S. Giuliano MilaneseCasella postale 438120098 San Giuliano Milanese Centro (MI)Italy� +39 02 98213-1 Telefax +39 02 98281595 [email protected]

Klüber Lubrication Benelux N.V.Energiestraat 51411 AN NaardenPostbus 1111400 AC BussumNetherlands� +31 35 6951464Telefax +31 35 [email protected]

Klüber Lubrication SkandinavienA/S, Filial NorgePostboks 721483 SkyttaNorway� +47 67067840Telefax +47 [email protected]

Klüber Lubrication Polskasp.z o.o.ul. Skoczowska 1961-345 PoznanPoland� +48 61 8700790Telefax +48 61 [email protected]

Klüber Lubrication GmbH Ibérica S. en C.Carretera C-17, Km 15,508150 Parets del Vallés (Barcelona)Spain� +34 93 5738400,Telefax +34 93 [email protected]

Klüber Lubrication SkandinavienA/S, Filial SverigeBox 601194 26 Upplands VäsbySweden� +46 8 59098600Telefax +46 8 [email protected]

Klüber Lubrication AG (Schweiz)Thurgauerstrasse 398050 ZürichSwitzerland� +41 1 3086969Telefax +41 1 [email protected]

Klüber LubricationYaglama ÜrünleriSanayi Ve Ticaret A.S.Cerkezköy Organize Sanayi BölgesiAtatürk Cad. 10 Sok. No: 7Cerkezköy/TekirdagTurkey� +90 282 7581530Telefax +90 282 [email protected]

Klüber Lubrication Great Britain Ltd.Hough MillsNorthowram, Halifax, HX3 7BNGreat Britain� +44 1422 205115Telefax +44 1422 [email protected]

Klüber Lubrication Argentina S.A.Martin J. Haedo 4301/63(1602) FloridaProv. Buenos AiresArgentina� +54 11 4709-1400Telefax +54 11 [email protected]

Klüber LubricationLubrificantes Especiais Ltda. & Cia.Rua São Paulo, 345Distrito Industrial de Alphaville06465-902 Barueri - São PauloBrazil� +55 11 4166-9000Telefax +55 11 4195-6832, [email protected]

Klüber Lubrication North America L.P.North American Headquarters32 Industrial DriveLondonderry, NH 03053USA� +1 603 647-4104Telefax +1 603 [email protected]

Klüber Lubrication North America L.P.Canadian officeOntarioCanada� +1 905 3049485Telefax +1 905 [email protected]

Klüber Lubrication TexasSummit Industrial Products, Inc.9010 County Road 2120Tyler, Texas 75707POB 131359Tyler, Texas 75713USA� +1 903 5348021Telefax +1 903 [email protected]

Klüber Lubrication Chile Ltda.Avda. Pdte. Eduardo Frei M. 9950oficina Nº 5, Cargo ParkQuilicura, Santiago Chile� +56 2 7471188Telefax +56 2 [email protected]

Klüber Lubricación Mexicana, S. A. de C. V.Boleo 62, Col. Maza, Del.Cuauhtemoc06270 Mexico, D.F.Mexico� +52 55 57020048Telefax +52 55 [email protected]

Klüber Lubrication China Ltd.Hong Kong OfficeUnit 18, 1/F., AdvancedTechnology CentreNo. 2, Choi Fat StreetSheung Shui, New TerritoriesHong KongChina� +852 26920191Telefax +852 [email protected]

Klüber Lubrication China Ltd.Beijing Representative OfficeRoom 610, Junefield PlazaNo. 6 Xuanwumenwai StreetXuanwu District, BeijingChinaPost Code: 100052� +8610 6310-3568, 6310-3569,6310-4504Telefax +8610 [email protected]

Klüber Lubrication China Ltd.Shenzhen Representative OfficeRM 2903, Huaneng BuildingShennanzhong RoadFutian District, Shenzhen CityChinaPostal Code: 518031� +86 755 8368-0482Telefax +86 755 [email protected]

Klüber Lubrication (Shanghai) Co. Ltd.Shanghai Liaison OfficeRm 2504, World Trade TowerNo.500 Guang Dong RoadShanghaiChina Postal Code: 200001� +86 21 63620160Telefax +86 21 [email protected]

Klüber Lubrication (Shanghai) Co. Ltd.Chengdu Liaison OfficeNew Times Plaza, 17 CWenwu Road, No. 42, Xinhua StreetChengdu, SichuanChinaPostal Code: 610017� +86 28 8675-2970, +86 28 8675-2971Telefax +86 28 [email protected]

Klüber Lubrication India Pvt. Ltd.504, A-Wing, Navbharat EstatesZakaria Bunder RoadSewri (West), Mumbai – 400 015India� +91 22 24178580,+91 22 24178740Telefax +91 22 [email protected]

NOK Klüber Co. Ltd.5th Floor Seidensha Bldg.1-10-11, Hamamatsu-ChoMinato-Ku, Tokyo, 105-0032Japan� +81 3 3434-1734Telefax +81 3 [email protected]

NOK Klüber Co. Ltd.Kitaibaraki Plant955-4, Aza - Ohishi, IsoharaIsoharamachi, Kitaibaraki-City Ibaraki – 319-15Japan� +81 293 427320, 425365Telefax +81 293 [email protected]

Klüber Lubrication Korea Ltd.Seoul Head OfficeSuite 802, Samhwan Camus Bldg. 17-3Yoido-Dong, Youngdungpo- kuSeoulKorea� +82 2 7825151Telefax +82 2 [email protected]

Klüber Lubrication Korea Ltd.Factory562 Okmyung-ri Daesong-myunNam-ku, Pohang, Gyungbuk 790-840Korea� +82 54 278-5151Telefax +82 54 [email protected]

Klüber Lubrication (Malaysia) Sdn. Bhd.No. 17 Jalan PJU 3/49Sunway Damansara Technology Park47810 Petaling JayaSelangor Darul EhsanMalaysia� +60 3 78034954Telefax +60 3 [email protected]

Klüber Lubrication South East Asia Pte. Ltd.25 International Business Park# 04-54 German CentreSingapore 609916� +65 65 629460Telefax +65 65 [email protected]

Klüber Lubrication (Pty) Ltd.P.O. Box 11461Randhart, Alberton 1457South Africa� +27 11 908-2457, -2458, -2459Telefax +27 11 [email protected]

Klüber Lubrication Australia Pty. Ltd.1st Floor, 3 Brand DriveP.O. Box 4Thomastown, VIC. 3074Australia� +61 3 94647577Telefax +61 3 [email protected]

Klüber Lubrication Australia Pty. Ltd.Sydney OfficeUnit 23, 380 Marion Street Condell Park, NSW 2200, Sydney Australia� +61 2 97908562Telefax +61 2 [email protected]

www.klueber.comKlüber Lubrication München KG a member of the Freudenberg group

special lubricants for textile machinery

Documents

textile machines

special machines

spinning machines

knitting machines

solid lubricants

sizing machines

use of special lubricants

spool winding machines